Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
toh:tenda:4g301 [2015/10/23 15:08] – created ufotoh:tenda:4g301 [2015/12/02 18:49] – tags added tmomas
Line 1: Line 1:
 +====== Tenda 4G301 ======
  
 +
 +====Serial Port====
 +===Pinout===
 +On the other side of the PCB there are 2 test points.
 +
 +The serial interface is 3.3V TTL levels (need USB cable and/or level converter to connect to a PC). Settings are 57k6 8N1 no flow control.
 +
 +====GPIO====
 +  * in 2: button or usb-charging power
 +  * out 0: usb-power
 +  * out 2: LED 1
 +  * out 40: LED 5
 +  * out 41/42: LED 2 (incl.red one)
 +  * out 43: LED 4
 +
 +===== Bootlogs =====
 +==== OEM bootlog ====
 +
 +<WRAP bootlog>
 +<nowiki>U-Boot 1.1.3 (Oct 21 2013 - 14:54:35)
 +
 +
 +Board: Ralink APSoC DRAM:  64 MB
 +
 +relocate_code Pointer at: 83fb4000
 +
 +enable ephy clock...done. rf reg 29 = 5
 +
 +SSC disabled.
 +
 +spi_wait_nsec: 29
 +
 +spi device id: ef 40 16 0 0 (40160000)
 +
 +find flash: W25Q32BV
 +
 +raspi_read: from:30000 len:1000
 +
 +*** Warning - bad CRC, using default environment
 +
 +
 +============================================
 +
 +Ralink UBoot Version: 4.1.1.0
 +
 +--------------------------------------------
 +
 +ASIC 7620_MP (Port5<->None)
 +
 +DRAM component: 512 Mbits DDR, width 16
 +
 +DRAM bus: 16 bit
 +
 +Total memory: 64 MBytes
 +
 +Flash component: SPI Flash
 +
 +Date:Oct 21 2013  Time:14:54:35
 +
 +============================================
 +
 +icache: sets:512, ways:4, linesz:32 ,total:65536
 +
 +dcache: sets:256, ways:4, linesz:32 ,total:32768
 +
 +
 + ##### The CPU freq = 580 MHZ ####
 +
 + estimate memory size =64 Mbytes
 +
 +
 +Please choose the operation:
 +
 +   1: Load system code to SDRAM via TFTP.
 +
 +   2: Load system code then write to Flash via TFTP.
 +
 +   3: Boot system code via Flash (default).
 +
 +   4: Entr boot command line interface.
 +
 +   7: Load Boot Loader code then write to Flash via Serial.
 +
 +   9: Load Boot Loader code then write to Flash via TFTP. 0
 +
 +
 +
 +3: System Boot system code via Flash.
 +
 +## Booting image at bc050000 ...
 +
 +raspi_read: from:50000 len:40
 +
 +   Image Name:   Linux Kernel Image
 +
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +
 +   Data Size:    2970642 Bytes =  2.8 MB
 +
 +   Load Address: 80000000
 +
 +   Entry Point:  8000c310
 +
 +raspi_read: from:50040 len:2d5412
 +
 +   Verifying Checksum ... OK
 +
 +   Uncompressing Kernel Image ... OK
 +
 +No initrd
 +
 +## Transferring control to Linux (at address 8000c310) ...
 +
 +## Giving linux memsize in MB, 64
 +
 +
 +Starting kernel ...
 +
 +
 +
 +LINUX started...
 +
 + THIS IS ASIC
 +Linux version 2.6.36 (root@bogon) (gcc version 3.4.2) #143 Sat Jun 21
 +06:03:01 EDT 2014
 +
 + The CPU feqenuce set to 580 MHz
 +
 + MIPS CPU sleep mode enabled.
 + PCIE: bypass PCIe DLL.
 + PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 + disable all power about PCIe
 + PCIE: PLL power down for MT7620N
 +CPU revision is: 00019650 (MIPS 24Kc)
 +Determined physical RAM map:
 + memory: 04000000 @ 00000000 (usable)
 +Initrd not found or empty - disabling initrd
 +Zone PFN ranges:
 +  Normal   0x00000000 -> 0x00004000
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00004000
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
 +PID hash table entries: 256 (order: -2, 1024 bytes)
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
 +Writing ErrCtl register=0003e67a
 +Readback ErrCtl register=0003e67a
 +Memory: 53100k/65536k available (4394k kernel code, 12436k reserved,
 +821k data, 6428k init, 0k highmem)
 +NR_IRQS:128
 +MTK/Ralink System Tick Counter init... cd:804ffe78, m:214748, s:32
 +console [ttyS1] enabled
 +Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
 +pid_max: default: 32768 minimum: 301
 +Mount-cache hash table entries: 512
 +NET: Registered protocol family 16
 +bio: create slab <bio-0> at 0
 +SCSI subsystem initialized
 +usbcore: registered new interface driver usbfs
 +usbcore: registered new interface driver hub
 +usbcore: registered new device driver usb
 +cfg80211: Calling CRDA to update world regulatory domain
 +Switching to clocksource Ralink external timer
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +UDP hash table entries: 256 (order: 0, 4096 bytes)
 +UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +NET: Registered protocol family 1
 +Load Ralink Timer0 Module
 +Load Ralink Timer1 Module
 +RT3xxx EHCI/OHCI init.
 +fuse init (API version 7.15)
 +msgmni has been set to 103
 +Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
 +io scheduler noop registered (default)
 +Ralink gpio driver initialized
 +Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
 +serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
 +serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
 +brd: module loaded
 +deice id : ef 40 16 0 0 (40160000)
 +W25Q32BV(ef 40160000) (4096 Kbytes)
 +mtd .name = raspi, .size = 0x00400000 (0M) .erasesize = 0x00000004 (0K)
 +.numeraseregions = 65536
 +Creating 6 MTD partitions on "raspi":
 +0x000000000000-0x000000400000 : "ALL"
 +0x000000000000-0x000000030000 : "Bootloader"
 +0x000000030000-0x000000040000 : "Config"
 +0x000000040000-0x000000050000 : "Factory"
 +0x000000050000-0x0000003f0000 : "Kernel"
 +0x0000003f0000-0x000000400000 : "Backup_config"
 +rdm_major = 253
 +SMACCR1 -- : 0x0000000c
 +SMACCR0 -- : 0x43762077
 +Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors
 +allocated, mtu = 1500!
 +SMACCR1 -- : 0x0000000c
 +SMACCR0 -- : 0x43762077
 +PROC INIT OK!
 +PPP generic driver version 2.4.2
 +PPP BSD Compression module registered
 +PPP MPPE Compression module registered
 +NET: Registered protocol family 24
 +
 +
 +=== pAd = c0003000, size = 806048 ===
 +
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +<-- RTMPAllocAdapterBlock, Status=0
 +AP Driver version-2.7.1.6
 +ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 +rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
 +rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
 +rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
 +rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
 +hub 1-0:1.0: USB hub found
 +hub 1-0:1.0: 1 port detected
 +ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 +rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
 +rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
 +rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
 +hub 2-0:1.0: USB hub found
 +hub 2-0:1.0: 1 port detected
 +usbcore: registered new interface driver cdc_acm
 +cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN
 +adapters
 +Initializing USB Mass Storage driver...
 +usbcore: registered new interface driver usb-storage
 +USB Mass Storage support registered.
 +usbcore: registered new interface driver ums-usbat
 +Netfilter messages via NETLINK v0.30.
 +nf_conntrack version 0.5.0 (829 buckets, 3316 max)
 +ctnetlink v0.93: registering with nfnetlink.
 +Create proc webstr success.
 +matchsize=264
 +xt_time: kernel timezone is -0000
 +net/netfilter/xt_netcheck.c 137 ipt_netcheck init
 +IPVS: Registered protocols ()
 +IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
 +IPVS: ipvs loaded.
 +ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
 +TCP cubic registered
 +NET: Registered protocol family 17
 +L2TP core driver, V2.0
 +PPPoL2TP kernel driver, V2.0
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +Freeing unused kernel memory: 6428k freed
 +
 +init started: BusyBox v1.12Algorithmics/MIPS FPU Emulator v1.5
 +.1 (2014-04-15 05:58:40 EDT)
 +
 +starting pid 32, tty '': '/etc_ro/rcS'
 +Welcome to
 +    _______  _______  ___     __  ____    _   ___
 +    |  ___  \|   __  ||     |__||    \ | || | /  /
 +    | |___| ||  |__| ||   |__  __ |     \| || |/  /
 +    |     /    ||      ||  || |\     ||     \
 +    |__| \__\|__| |__||______||__||_| \____||_|\___\
 +
 +                 =System Architecture Department=
 +
 +
 +starting pid 47, tty '/dev/ttyS1': '/bin/login'
 +(none) login: SOFT_WARE_VERSION V1.01.27
 +SOFT_WARE_VERSION V1.01.27
 +LANGUAGE_INFO en
 +HW_VERSION V1.0
 +SVN_VERSION 537
 +BUILD_TIME Jun 21 2014 05:57:25
 +BACK config init OK, old crc=ace7c67b, real crc=ace7c67b
 +##########
 +nvramDestroy=0
 +backUPDestroy=0
 +##########
 +none config destroy..., nothing to do
 +
 +
 +Yes:
 +
 +      ****** WeLoveLinux ******
 +
 + Welcome to ...
 +cat: can't open '/var/tenda_httpd.log': No such file or directory
 +sh: cannot create /proc/sys/net/ipv4/conf/br0/accept_local: nonexistent
 +directory
 +usbcore: registered new interface driver usbserial
 +USB Serial support registered for generic
 +usbcore: registered new interface driver usbserial_generic
 +usbserial: USB Serial Driver core
 +USB Serial support registered for Sierra USB modem
 +usbcore: registered new interface driver sierra
 +sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
 +USB Serial support registered for GSM modem (1-port)
 +usbcore: registered new interface driver option
 +option: v0.7.2:USB Driver for GSM modems
 +USB Serial support registered for debug
 +usbcore: registered new interface driver debug
 +
 +==>down wireless interface!
 +RX DESC a32d0000  size = 2048
 +RTMP_TimerListAdd: add timer obj c0098438!
 +RTMP_TimerListAdd: add timer obj c00638e8!
 +RTMP_TimerListAdd: add timer obj c00638bc!
 +RTMP_TimerListAdd: add timer obj c0063890!
 +RTMP_TimerListAdd: add timer obj c000b018!
 +RTMP_TimerListAdd: add timer obj c000ac0c!
 +RTMP_TimerListAdd: add timer obj c000afe8!
 +RTMP_TimerListAdd: add timer obj c000b324!
 +RTMP_TimerListAdd: add timer obj c000b264!
 +RTMP_TimerListAdd: add timer obj c000b294!
 +RTMP_TimerListAdd: add timer obj c0065cec!
 +RTMP_TimerListAdd: add timer obj c00658e0!
 +RTMP_TimerListAdd: add timer obj c0065cbc!
 +RTMP_TimerListAdd: add timer obj c0065ff8!
 +RTMP_TimerListAdd: add timer obj c0065d1c!
 +RTMP_TimerListAdd: add timer obj c0065d4c!
 +RTMP_TimerListAdd: add timer obj c0065d7c!
 +RTMP_TimerListAdd: add timer obj c006eda4!
 +RTMP_TimerListAdd: add timer obj c006eec0!
 +RTMP_TimerListAdd: add timer obj c006edd0!
 +RTMP_TimerListAdd: add timer obj c00663a4!
 +RTMP_TimerListAdd: add timer obj c00084d8!
 +RTMP_TimerListAdd: add timer obj c00660b4!
 +APSDCapable[0]=0
 +APSDCapable[1]=0
 +APSDCapable[2]=0
 +APSDCapable[3]=0
 +APSDCapable[4]=0
 +APSDCapable[5]=0
 +APSDCapable[6]=0
 +APSDCapable[7]=0
 +APSDCapable[8]=0
 +APSDCapable[9]=0
 +APSDCapable[10]=0
 +APSDCapable[11]=0
 +APSDCapable[12]=0
 +APSDCapable[13]=0
 +APSDCapable[14]=0
 +APSDCapable[15]=0
 +default ApCliAPSDCapable[0]=0
 +1. Phy Mode = 9
 +2. Phy Mode = 9
 +E2PROM: D0 target power=0xff20
 +E2PROM: 40 MW Power Delta= 0
 +3. Phy Mode = 9
 +AntCfgInit: primary/secondary ant 0/1
 +Initialize RF Central Registers for E2 !!!
 +Initialize RF Central Registers for E3 !!!
 +Initialize RF Channel Registers for E2 !!!
 +Initialize RF Channel Registers for E3 !!!
 +Initialize RF DCCal Registers for E2 !!!
 +Initialize RF DCCal Registers for E3 !!!
 +D1 = 0, D2 = 12, CalCode = 28 !!!
 +RT6352_Temperature_Init : BBPR49 = 0x0
 +RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff6
 +Current Temperature from BBP_R49=0xfffffff2
 + TX BW Filter Calibration !!!
 + RX BW Filter Calibration !!!
 +LOFT Calibration Done!
 +IQCalibration Start!
 +IQCalibration Done! CH = 0, (gain= f, phase= 1)
 +IQCalibration Start!
 +IQCalibration Done! CH = 1, (gain= f, phase= 0)
 +TX IQ Calibration Done!
 +internal ALC is not enabled in NVM !
 +MCS Set = ff ff 00 00 01
 +RTMP_TimerListAdd: add timer obj c0066680!
 +Main bssid = c8:3a:35:2f:32:58
 +<==== rt28xx_init, Status=0
 +0x1300 = 00064380
 +Raeth v3.0 (Tasklet,SkbRecycle)
 +
 +phy_tx_ring = 0x02d72000, tx_ring = 0xa2d72000
 +
 +phy_rx_ring0 = 0x02d73000, rx_ring0 = 0xa2d73000
 +SMACCR1 -- : 0x0000000c
 +SMACCR0 -- : 0x43762077
 +CDMA_CSG_CFG = 81000000
 +GDMA1_FWD_CFG = 20710000
 +This crc is same as Old, ace7c67b, no need to write to flash.
 +maclist:
 +WLan[C8:3A:35:2F:32:58]
 +Lan[C8:3A:35:2F:ra2880stop()...32Done
 +:58]
 +Wan[C8:3A:35:2F:32:5D]
 +Free TX/RX Ring Memory!
 +Raeth v3.0 (Tasklet,SkbRecycle)
 +
 +phy_tx_ring = 0x02d76000, tx_ring = 0xa2d76000
 +
 +phy_rx_ring0 = 0x0336f000, rx_ring0 = 0xa336f000
 +SMACCR1 -- : 0x0000c83a
 +SMACCR0 -- : 0x352f3258
 +CDMA_CSG_CFG = 81000000
 +GDMA1_FWD_CFG = 20710000
 +ifconfig: SIOCSIFHWADDR: Device or resource busy
 +-------------
 +WISP_MODE
 +--------------
 +vconfig: ioctl error for set_ingress_map: No such device
 +vconfig: ioctl error for set_ingress_map: No such device
 +vconfig: ioctl error for set_ingress_map: No such device
 +vconfig: ioctl error for set_ingress_map: No such device
 +vconfig: ioctl error for set_ingress_map: No such device
 +vconfig: ioctl error for set_ingress_map: No such device
 +vconfig: ioctl error for set_ingress_map: No such device
 +vconfig: ioctl error for set_ingress_map: No such device
 +vconfig: ioctl error for set_egress_map: No such device
 +vconfig: ioctl error for set_egress_map: No such device
 +vconfig: ioctl error for set_egress_map: No such device
 +vconfig: ioctl error for set_egress_map: No such device
 +vconfig: ioctl error for set_egress_map: No such device
 +vconfig: ioctl error for set_egress_map: No such device
 +vconfig: ioctl error for set_egress_map: No such device
 +vconfig: ioctl error for set_egress_map: No such device
 +switch reg write offset=2004, value=ff0003
 +switch reg write offset=2104, value=ff0003
 +switch reg write offset=2204, value=ff0003
 +switch reg write offset=2304, value=ff0003
 +switch reg write offset=2404, value=ff0003
 +switch reg write offset=2504, value=ff0003
 +switch reg write offset=2010, value=810000c0
 +switch reg write offset=2110, value=810000c0
 +switch reg write offset=2210, value=810000c0
 +switch reg write offset=2310, value=810000c0
 +switch reg write offset=2410, value=810000c0
 +switch reg write offset=2510, value=810000c0
 +switch reg write offset=2610, value=81000000
 +switch reg write offset=2710, value=81000000
 +switch reg write offset=2604, value=20ff0003
 +switch reg write offset=2704, value=20ff0003
 +switch reg write offset=2610, value=81000000
 +switch reg write offset=2014, value=10001
 +switch reg write offset=2114, value=10001
 +switch reg write offset=2214, value=10001
 +switch reg write offset=2314, value=10001
 +switch reg write offset=2414, value=10002
 +switch reg write offset=2514, value=10001
 +device eth2.1 entered promiscuous mode
 +device eth2 entered promiscuous mode
 +device eth2.2 entered promiscuous mode
 +br0: port 2(eth2.2) entering learning state
 +br0: port 2(eth2.2) entering learning state
 +br0: port 1(eth2.1) entering learning state
 +br0: port 1(eth2.1) entering learning state
 +Unable to open /etc/udhcpd.leases for reading
 +Init tQoS dev success.
 +open /dev/tQoS failed.
 +Set: phy[0].reg[1] = 3900
 +Set: phy[0].reg[2] = 3900
 +Set: phy[0].reg[3] = 3900
 +device ra0 entered promiscuous mode
 +br0: port 3(ra0) entering learning state
 +br0: port 3(ra0) entering learning state
 +br0: port 2(eth2.2) entering forwarding state
 +br0: port 1(eth2.1) entering forwarding state
 +2000, 1, 1
 +usbcore: registered new interface driver cdc_ether
 +/var/run/dnrd.pid /var/run/dnrd.pid
 +==>up wireless interface sucess!Create check wan thread, tid=00000402, ret=0
 +=====>func:main line:563 netctrl Go to loop NOW, soft
 +version=V1.01.27-------------
 +br0: port 3(ra0) entering forwarding state
 +
 +
 +Httpd listen 192.168.2.1:80
 +
 +main--504
 +semget error: or exist: File exists
 +semId has exist 0
 +=====>func:handleMessage line:129 type=51-------------
 +
 +(none) login:</nowiki>
 +</WRAP>\\
 +
 +==== OpenWrt bootlog ====
 +
 +starting openwrt via ram-image
 +<WRAP bootlog>
 +<nowiki>============================================
 +
 +Ralink UBoot Version: 4.1.1.0
 +
 +--------------------------------------------
 +
 +ASIC 7620_MP (Port5<->None)
 +
 +DRAM component: 512 Mbits DDR, width 16
 +
 +DRAM bus: 16 bit
 +
 +Total memory: 64 MBytes
 +
 +Flash component: SPI Flash
 +
 +Date:Oct 21 2013  Time:14:54:35
 +
 +============================================
 +
 +icache: sets:512, ways:4, linesz:32 ,total:65536
 +
 +dcache: sets:256, ways:4, linesz:32 ,total:32768
 +
 +
 + ##### The CPU freq = 580 MHZ ####
 +
 + estimate memory size =64 Mbytes
 +
 +
 +Please choose the operation:
 +
 +   1: Load system code to SDRAM via TFTP.
 +
 +   2: Load system code then write to Flash via TFTP.
 +
 +   3: Boot system code via Flash (default).
 +
 +   4: Entr boot command line interface.
 +
 +   7: Load Boot Loader code then write to Flash via Serial.
 +
 +   9: Load Boot Loader code then write to Flash via TFTP.
 +
 +
 +
 +You choosed 1
 + 0
 +
 +raspi_read: from:40028 len:6
 +
 +
 +
 +
 +1: System Load Linux to SDRAM via TFTP.
 +
 + Please Input new ones /or Ctrl-C to discard
 +
 + Input device IP (192.168.2.1) ==:192.168.2.11
 +
 + Input server IP (192.168.2.64) ==:192.168.2.64
 +
 + Input Linux Kernel filename () ==:uImage
 +
 +
 + netboot_common, argc= 3
 +
 +
 + NetTxPacket = 0x83FE4E80
 +
 +
 + KSEG1ADDR(NetTxPacket) = 0xA3FE4E80
 +
 +
 + NetLoop,call eth_halt !
 +
 +
 + NetLoop,call eth_init !
 +
 +Trying Eth0 (10/100-M)
 +
 +
 + Waitting for RX_DMA_BUSY status Start... done
 +
 +
 +
 + ETH_STATE_ACTIVE!!
 +
 +TFTP from server 192.168.2.64; our IP address is 192.168.2.11
 +
 +Filename 'uImage'.
 +
 +
 + TIMEOUT_COUNT=10,Load address: 0x80a00000
 +
 +Loading: Got ARP REPLY, set server/gtwy eth addr (00:1c:ad:77:f2:0e)
 +
 +Got it
 +
 +#################################################################
 +
 + #################################################################
 +
 + #################################################################
 +
 + #################################################################
 +
 + #################################################################
 +
 + #################################################################
 +
 + #################################################################
 +
 + #################################################################
 +
 + #################################################################
 +
 + ###################
 +
 +done
 +
 +Bytes transferred = 3090502 (2f2846 hex)
 +
 +NetBootFileXferSize= 002f2846
 +
 +raspi_read: from:30000 len:10000
 +
 +Erasing SPI Flash...
 +
 +raspi_erase: offs:30000 len:10000
 +
 +.
 +
 +Writing to SPI Flash...
 +
 +raspi_write: to:30000 len:10000
 +
 +.
 +
 +done
 +
 +Automatic boot of image at addr 0x80A00000 ...
 +
 +## Booting image at 80a00000 ...
 +
 +   Image Name:   MIPS OpenWrt Linux-3.18.21
 +
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +
 +   Data Size:    3090438 Bytes =  2.9 MB
 +
 +   Load Address: 80000000
 +
 +   Entry Point:  80000000
 +
 +   Verifying Checksum ... OK
 +
 +   Uncompressing Kernel Image ... OK
 +
 +No initrd
 +
 +## Transferring control to Linux (at address 80000000) ...
 +
 +## Giving linux memsize in MB, 64
 +
 +
 +Starting kernel ...
 +
 +
 +[    0.000000] Linux version 3.18.21 (daniel@box) (gcc version 4.8.3
 +(OpenWrt/Linaro GCC 4.8-2014.04 r47238) ) #2 Fri Oct 23 04:42:48 CEST 2015
 +[    0.000000] Board has DDR2
 +[    0.000000] Analog PMU set to hw control
 +[    0.000000] Digital PMU set to hw control
 +[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:3
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
 +[    0.000000] MIPS: machine is Tenda 4G301
 +[    0.000000] Determined physical RAM map:
 +[    0.000000]  memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
 +[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
 +bytes.
 +[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases,
 +linesize 32 bytes
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.
 +Total pages: 16256
 +[    0.000000] Kernel command line: console=ttyS0,57600
 +rootfstype=squashfs,jffs2
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Writing ErrCtl register=0003e66e
 +[    0.000000] Readback ErrCtl register=0003e66e
 +[    0.000000] Memory: 59320K/65536K available (2750K kernel code, 131K
 +rwdata, 544K rodata, 1940K init, 192K bss, 6216K reserved)
 +[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
 +[    0.000000] NR_IRQS:256
 +[    0.000000] CPU Clock: 580MHz
 +[    0.000000] systick: enable autosleep mode
 +[    0.000000] systick: running - mult: 214748, shift: 32
 +[    0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
 +[    0.070000] pid_max: default: 32768 minimum: 301
 +[    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
 +bytes)
 +[    0.090000] pinctrl core: initialized pinctrl subsystem
 +[    0.100000] NET: Registered protocol family 16
 +[    0.120000] rt2880_gpio 10000600.gpio: registering 24 gpios
 +[    0.130000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
 +[    0.140000] rt2880_gpio 10000638.gpio: registering 16 gpios
 +[    0.150000] rt2880_gpio 10000638.gpio: registering 16 irq handlers
 +[    0.160000] rt2880_gpio 10000660.gpio: registering 32 gpios
 +[    0.170000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
 +[    0.180000] rt2880_gpio 10000688.gpio: registering 1 gpios
 +[    0.190000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
 +[    0.200000] Switched to clocksource systick
 +[    0.210000] NET: Registered protocol family 2
 +[    0.210000] TCP established hash table entries: 1024 (order: 0, 4096
 +bytes)
 +[    0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.240000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.250000] TCP: reno registered
 +[    0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.270000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.280000] NET: Registered protocol family 1
 +[    2.950000] rt-timer 10000100.timer: maximum frequency is 2441Hz
 +[    2.970000] futex hash table entries: 256 (order: -1, 3072 bytes)
 +[    2.990000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    3.000000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
 +(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    3.030000] msgmni has been set to 115
 +[    3.040000] io scheduler noop registered
 +[    3.040000] io scheduler deadline registered (default)
 +[    3.060000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
 +[    3.070000] console [ttyS0] disabled
 +[    3.080000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20,
 +base_baud = 2500000) is a 16550A
 +[    3.090000] console [ttyS0] enabled
 +[    3.090000] console [ttyS0] enabled
 +[    3.110000] bootconsole [early0] disabled
 +[    3.110000] bootconsole [early0] disabled
 +[    3.130000] m25p80 spi32766.0: found w25q32, expected gd25q32
 +[    3.140000] m25p80 spi32766.0: w25q32 (4096 Kbytes)
 +[    3.150000] 5 ofpart partitions found on MTD device spi32766.0
 +[    3.160000] Creating 5 MTD partitions on "spi32766.0":
 +[    3.170000] 0x000000000000-0x000000030000 : "u-boot"
 +[    3.180000] 0x000000030000-0x000000040000 : "u-boot-env"
 +[    3.200000] 0x000000040000-0x000000050000 : "factory"
 +[    3.210000] 0x000000050000-0x0000003f0000 : "firmware"
 +[    3.250000] 0x0000003f0000-0x000000400000 : "u-boot-env2"
 +[    3.260000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
 +[    3.280000] ralink_soc_eth 10100000.ethernet eth0: ralink at
 +0xb0100000, irq 5
 +[    3.290000] rt2880_wdt 10000120.watchdog: Initialized
 +[    3.300000] TCP: cubic registered
 +[    3.310000] NET: Registered protocol family 10
 +[    3.320000] NET: Registered protocol family 17
 +[    3.330000] bridge: automatic filtering via arp/ip/ip6tables has been
 +deprecated. Update your scripts to load br_netfilter if you need this.
 +[    3.360000] 8021q: 802.1Q VLAN Support v1.8
 +[    3.380000] Freeing unused kernel memory: 1940K (8035b000 - 80540000)
 +[    3.400000] init: Console is alive
 +[    3.410000] init: - watchdog -
 +[    3.440000] usbcore: registered new interface driver usbfs
 +[    3.450000] usbcore: registered new interface driver hub
 +[    3.460000] usbcore: registered new device driver usb
 +[    3.480000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 +[    3.490000] ehci-platform: EHCI generic platform driver
 +[    3.700000] phy phy-usbphy.0: remote usb device wakeup disabled
 +[    3.710000] phy phy-usbphy.0: UTMI 16bit 30MHz
 +[    3.720000] ehci-platform 101c0000.ehci: EHCI Host Controller
 +[    3.730000] ehci-platform 101c0000.ehci: new USB bus registered,
 +assigned bus number 1
 +[    3.750000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
 +[    3.780000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
 +[    3.790000] hub 1-0:1.0: USB hub found
 +[    3.800000] hub 1-0:1.0: 1 port detected
 +[    3.810000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 +[    3.820000] ohci-platform: OHCI generic platform driver
 +[    3.830000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
 +[    3.850000] ohci-platform 101c1000.ohci: new USB bus registered,
 +assigned bus number 2
 +[    3.860000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
 +[    3.930000] hub 2-0:1.0: USB hub found
 +[    3.940000] hub 2-0:1.0: 1 port detected
 +[    4.420000] init: - preinit -
 +[    4.520000] 8021q: adding VLAN 0 to HW filter on device eth0
 +Press the [f] key and hit [enter] to enter failsafe mode
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
 +[    7.690000] procd: - early -
 +[    7.700000] procd: - watchdog -
 +[    8.270000] procd: - ubus -
 +[    9.280000] random: ubusd urandom read with 14 bits of entropy available
 +[    9.300000] procd: - init -
 +Please press Enter to activate this console.
 +[    9.880000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[    9.900000] Loading modules backported from Linux version
 +master-2015-07-21-0-g47cd203
 +[    9.920000] Backport generated by backports.git
 +backports-20150626-0-gc1a4168
 +[    9.950000] cfg80211: World regulatory domain updated:
 +[    9.960000] cfg80211:  DFS Master region: unset
 +[    9.970000] cfg80211:   (start_freq - end_freq @ bandwidth),
 +(max_antenna_gain, max_eirp), (dfs_cac_time)
 +[    9.990000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz),
 +(N/A, 2000 mBm), (N/A)
 +[   10.000000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz),
 +(N/A, 2000 mBm), (N/A)
 +[   10.020000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz),
 +(N/A, 2000 mBm), (N/A)
 +[   10.030000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz,
 +160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
 +[   10.050000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz,
 +160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
 +[   10.070000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz),
 +(N/A, 2000 mBm), (0 s)
 +[   10.090000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz),
 +(N/A, 2000 mBm), (N/A)
 +[   10.100000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz),
 +(N/A, 0 mBm), (N/A)
 +[   10.180000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   10.200000] nf_conntrack version 0.5.0 (957 buckets, 3828 max)
 +[   10.260000] xt_time: kernel timezone is -0000
 +[   10.280000] PPP generic driver version 2.4.2
 +[   10.290000] NET: Registered protocol family 24
 +[   10.310000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390,
 +rev 0500 detected
 +[   10.330000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620
 +detected
 +[   16.090000] 8021q: adding VLAN 0 to HW filter on device eth0
 +[   16.100000] device eth0.1 entered promiscuous mode
 +[   16.110000] device eth0 entered promiscuous mode
 +[   16.140000] br-lan: port 1(eth0.1) entered forwarding state
 +[   16.150000] br-lan: port 1(eth0.1) entered forwarding state
 +[   18.150000] br-lan: port 1(eth0.1) entered forwarding state
 +
 +
 +
 +BusyBox v1.23.2 (2015-10-23 04:36:59 CEST) built-in shell (ash)
 +
 +  _______                     ________        __
 +       |.-----.-----.-----.|  |  |  |.----.|  |_
 +     ||  _  |  -__|     ||  |  |  ||   _||   _|
 + |_______||   __|_____|__|__||________||__|  |____|
 +          |__| W I R E L E S S   F R E E D O M
 + -----------------------------------------------------
 + DESIGNATED DRIVER (Bleeding Edge, r47238)
 + -----------------------------------------------------
 +  * 2 oz. Orange Juice         Combine all juices in a
 +  * 2 oz. Pineapple Juice      tall glass filled with
 +  * 2 oz. Grapefruit Juice     ice, stir well.
 +  * 2 oz. Cranberry Juice
 + -----------------------------------------------------
 +root@OpenWrt:/#
 +root@OpenWrt:/# cat /tmp/sysinfo/
 +*
 +v7t4g301
 +Tenda 4G301
 +root@OpenWrt:/# uptime
 +
 + 00:03:50 up 0 min,  load average: 0.86, 0.22, 0.07</nowiki>
 +</WRAP>\\
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>4flash 64ram}}