Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:telsey:cpa-znte60t [2016/04/04 20:33] – RT2661T is 802.11b/g, doesn't support 802.11n Berninitoh:telsey:cpa-znte60t [2019/08/19 17:07] – Dead link removed tmomas
Line 1: Line 1:
 ====== Telsey CPA-ZNTE60T ====== ====== Telsey CPA-ZNTE60T ======
 +
 +{{section>meta:infobox:432_warning#infobox_for_dataentries&noheader&nofooter&noeditbutton}}
 +
 ADSL Wireless Voice Gateway, series CPVA642. ADSL Wireless Voice Gateway, series CPVA642.
 Some Fastweb HAGs (italian broadband provider) have this hardware. Some Fastweb HAGs (italian broadband provider) have this hardware.
  
 ===== Supported Versions ===== ===== Supported Versions =====
-Supported, but without ADSL. +---- datatable ---- 
-  * Attitude Adjustment (12.09):\\ [[http://downloads.openwrt.org/attitude_adjustment/12.09/brcm63xx/generic/openwrt-CPA-ZNTE60T-squashfs-cfe.bin|openwrt-CPA-ZNTE60T-squashfs-cfe.bin]] +cols    : Brand, Model, Versions, Supported Current RelOEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid 
-  * Trunk:\\ [[http://downloads.openwrt.org/snapshots/trunk/brcm63xx/openwrt-CPA-ZNTE60T-squashfs-cfe.bin|openwrt-CPA-ZNTE60T-squashfs-cfe.bin]]+headers Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data 
 +align   c,c,c,c,c,c,
 +filter  : Model=CPA-ZNTE60T 
 +---- 
 + 
 +---- datatable ---
 +cols    : Unsupported Functions_unsupporteds 
 +filter  : Model=CPA-ZNTE60T 
 +----
  
  
 ===== Hardware Highlights ===== ===== Hardware Highlights =====
-CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ Other ^ +---- datatable ---- 
-| BCM96358 | 32MiB | 8MiB | x 1| Yes | Yes | Yes | ADSL |+cols    : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, RAM MB_mbram, WLAN Hardware, WLAN 2.4GHz, WLAN 5.0GHz, Ethernet 100M ports_, Ethernet Gbit ports_, Modem, USB ports_ 
 +header  : Model, Version,SoC,CPU MHz,Flash MB,RAM MB,WLAN Hardware,WLAN2.4,WLAN5.0,100M ports,Gbit ports,Modem,USB 
 +align   : c,c,c,c,c,c,c,c,c,c,c,c,
 +filter  : Model=CPA-ZNTE60T 
 +---- 
  
 ===== Installation ===== ===== Installation =====
 +---- datatable ----
 +cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url
 +headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock
 +align   : c,c,c
 +filter  : Model=CPA-ZNTE60T
 +----
 +
 +-> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]]
 +
  
 Initial installation can be done from the stock firmware web interface, or from the CFE web interface.  Unfortunately installation via TFTP seems to have been disabled for this device. Initial installation can be done from the stock firmware web interface, or from the CFE web interface.  Unfortunately installation via TFTP seems to have been disabled for this device.
  
-One important note is that the CPVA642 models have a dual image setup.  That means if an image fails to boot, the system will fall back to the other image installed, for the stock firmware.  We don't actually want this, because it means that if you flash via the CFE web interface when there is already a good image, the image will not be written to the start of flash but to a point 4MB from the start (i.e. as if there were two 4MB images).  This confuses OpenWRT.  +One important note is that the CPVA642 models have a dual image setup. That means if an image fails to boot, the system will fall back to the other image installed, for the stock firmware. We don't actually want this, because it means that if you flash via the CFE web interface when there is already a good image, the image will not be written to the start of flash but to a point 4MB from the start (i.e. as if there were two 4MB images). This confuses OpenWrt.  
  
 That means if you have a successfully flash image and you want to flash via the CFE web interface, you need to erase everthing except the bootloader first. That means if you have a successfully flash image and you want to flash via the CFE web interface, you need to erase everthing except the bootloader first.
Line 23: Line 48:
 ===== Hardware ===== ===== Hardware =====
 ==== Info ==== ==== Info ====
-| **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] | +[[wp>Instruction set|Architecture]]    | [[wp>MIPS architecture|MIPS]] | 
-| **Vendor:**          | [[wp>Broadcom]] | +Vendor          | [[wp>Broadcom]] | 
-| **[[doc:techref:Bootloader]]:**     | [[doc:techref:bootloader:CFE]] | +[[docs:techref:bootloader]]  | [[docs:techref:bootloader:cfe]] | 
-| **Board Id:**     | CPVA642 | +Board Id        | CPVA642 | 
-| **[[doc:hardware:soc|System-On-Chip]]:**  | BCM6358 | +[[docs:techref:hardware:soc|System-On-Chip]]  | BCM6358 | 
-| **[[doc:hardware:cpu|CPU]]/Speed**        | BMIPS4350 V1.0 / 300 Mhz [[doc:hardware:soc:soc.broadcom.bcm63xx:smp|BMIPS Dual Core]] | +[[docs:techref:hardware:cpu|CPU]]/Speed       | BMIPS4350 V1.0 / 300 MHz [[docs:techref:hardware:soc:soc.broadcom.bcm63xx:smp|BMIPS Dual Core]] | 
-| **Flash-Chip:**      | Macronix 29LV640D | +Flash-Chip      | Macronix 29LV640D | 
-| **Flash size:**      | 8 MiB | +Flash size      | 8 MiB | 
-| **RAM size :**             | 32 MiB | +RAM size        | 32 MiB | 
-| **Wireless:**        | Ralink RT2661T +Wireless        | Ralink RT2661T 
-| **Wireless standard:** | 802.11b/g | +Wireless standard | 802.11b/g | 
-| **Ethernet:**        | Broadcom  {{:media:datasheets:bcm5325_pinout.png?linkonly|BCM5325}} w/ vlan support [[doc:uci:network#swconfig]] | +Ethernet        | Broadcom  {{:media:datasheets:bcm5325_pinout.png?linkonly|BCM5325}} w/ vlan support [[docs:techref:swconfig]] | 
-| **Internet:**        | ADSL2+ +Internet        | ADSL2+ 
-| **USB:**             | 1x2.0H | +USB             | 1x2.0H | 
-| **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|Yes]] | +[[docs:techref:hardware:port.serial|Serial]]          | [[#Serial|Yes]] | 
-| **[[doc:hardware:port.jtag|JTAG]]:**            | [[#JTAG|Yes]]  |+[[docs:techref:hardware:port.jtag|JTAG]]            | [[#JTAG|Yes]]  |
  
  
Line 74: Line 99:
 ==== JTAG ==== ==== JTAG ====
  
-How to connect to JTAG interface, and how to reflash the device with [[http://downloads.openwrt.org/tools/oem/jtag/tools.zip|JTAG tools]]+How to connect to JTAG interface, and how to reflash the device with JTAG tools
  
-See [[doc:hardware:port.jtag]] for more JTAG details.+See [[docs:techref:hardware:port.jtag]] for more JTAG details.
  
 ==== Failsafe mode ==== ==== Failsafe mode ====
Line 109: Line 134:
  
 ===== Tags ===== ===== Tags =====
-{{tag>bcm6358 bcm63xx}}+{{tag>bcm6358 bcm63xx 8flash 32ram ADSL2+}}
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1