Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
toh:t-com:spw724vtypc [2015/10/04 15:42] – created dangoletoh:t-com:spw724vtypc [2019/10/16 10:37] – Tags section added tmomas
Line 1: Line 1:
 +====== T-Com Speedport W724V Typ C ======
 +THIS PAGE IS IN WORK IN PROGRESS!
  
 +===== Hardware =====
 +
 +^ SOC                      | 1     | Broadcom BCM63168D0   | brcm63xx   |
 +^ Flash                    | 1     | NAND                  | ?          |
 +^ RAM                      | 2     | 128MB                 | ?          |
 +^ WLAN B/G/N               | 1     | integrated            | broadcom   |
 +^ WLAN AC                  | 1     | mPCIe module          | broadcom   |
 +^ LAN                      | 5     | Broadcom BCM53125     | b53        |
 +^ Dect                     | 1     | ?                     | ?          |
 +^ Modem                    | 1     | integrated            | broadcom   |
 +^ Analog telephone ports   | 2     | ?                     | ?          |
 +^ USB                      | YES   |
 +^ Serial Port              | YES   |
 +^ JTAG                     | ?     |
 +^ mPCIe slot (!)           | YES (used for 802.11a WiFi module) |
 +
 +===== Serial Port =====
 +3.3V TTL serial on unpopulated pin-header 'J4'
 +
 +^ 1   | VCC   |
 +^ 2   | RX    |
 +^ 3   | TX    |
 +^ 4   | GND   |
 +
 +pin 1 is the pin market with an arrow.
 +
 +===== Bootlogs =====
 +==== OEM bootlog ====
 +<WRAP bootlog>
 +<nowiki>HELO
 +CPUI
 +L1CI
 +HELO
 +CPUI
 +L1CI
 +DRAM
 +----
 +PHYS
 +STRF
 +400H
 +PHYE
 +DDR2
 +SIZ4
 +SIZ3
 +SIZ2
 +DINT
 +USYN
 +LSYN
 +MFAS
 +LMBE
 +RACE
 +PASS
 +----
 +ZBSS
 +CODE
 +DATA
 +L12F
 +MAIN
 +ro08
 +SUN2
 +init
 +clen
 +find
 +flag
 +init
 +clen
 +find
 +flag
 +SUN6
 +002
 +002
 +001
 +001
 +RAM1
 +NAN3
 +RFS0
 +NAN5
 +
 +
 +CFE version 1.0.38-114.185 for BCM963268 (32bit,SP,BE)
 +Build Date: 2014年 02月 28日 星期五 14:56:12 CST (bruce@localhost)
 +Copyright (C) 2000-2011 Broadcom Corporation.
 +
 +NAND flash device: name , id 0x92f1 block 128KB size 131072KB
 +External switch id = 53125 
 +Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 134217728 bytes (128MB)
 +Boot Address: 0xb8000000
 +
 +read block 1 error
 +find flag begin read flash map
 +Board IP address                  : 192.168.1.1:ffffff00  
 +Host IP address                   : 192.168.1.100  
 +Gateway IP address                :   
 +Run from flash/host (f/h)         : f  
 +Default host run file name        : vmlinux  
 +Default host flash file name      : bcm963xx_fs_kernel  
 +Boot delay (0-9 seconds)          : 1  
 +Board Id (0-26)                   : 963268MBV  
 +Number of MAC Addresses (1-32)    : 16  
 +Base MAC Address                  : 00:0e:8f:xx:xx:xx  
 +PSI Size (1-64) KBytes            : 24  
 +Enable Backup PSI [0|1]           : 0  
 +System Log Size (0-256) KBytes    : 0  
 +Auxillary File System Size Percent: 0  
 +Main Thread Number [0|1]          : 0  
 +Voice Board Configuration (0-5)   : LE88266  
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 110
 +Flash Sector Number : 901.
 +
 +***************************************************
 +         Boot Version 1.0.8.0
 +
 +***************************************************
 +Entering Firmware : Everything is OK.
 +begin check sum
 +safe value is 255
 +check sum ok 
 +Booting from First image (0xb8520000) ...
 +Decompression OK!
 +Entry at 0x80392f70
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x80392f70
 +Linux version 2.6.30 (root@ubuntu) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Fri Jul 11 02:04:51 CST 2014
 +BCM Flash API. Flash device is not found.
 +963268MBV prom init
 +CPU revision is: 0002a080 (Broadcom4350)
 +DSL SDRAM reserved: 0x132000
 +Determined physical RAM map:
 + memory: 07ece000 @ 00000000 (usable)
 +Zone PFN ranges:
 +  DMA      0x00000000 -> 0x00001000
 +  Normal   0x00001000 -> 0x00007ece
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00007ece
 +On node 0 totalpages: 32462
 +free_area_init_node: node 0, pgdat 80486130, node_mem_map 81000000
 +  DMA zone: 32 pages used for memmap
 +  DMA zone: 0 pages reserved
 +  DMA zone: 4064 pages, LIFO batch:0
 +  Normal zone: 222 pages used for memmap
 +  Normal zone: 28144 pages, LIFO batch:7
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32208
 +Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200
 +wait instruction: enabled
 +Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
 +Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +NR_IRQS:128
 +PID hash table entries: 512 (order: 9, 2048 bytes)
 +console [ttyS0] enabled
 +Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
 +Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Allocating memory for DSP module core and initialization code
 +Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
 +Memory: 123444k/129848k available (3630k kernel code, 6232k reserved, 955k data, 168k init, 0k highmem)
 +Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)
 +Mount-cache hash table entries: 512
 +--Kernel Config--
 +  SMP=1
 +  PREEMPT=1
 +  DEBUG_SPINLOCK=0
 +  DEBUG_MUTEXES=0
 +Broadcom Logger v0.1 Jul 11 2014 01:35:45
 +CPU revision is: 0002a080 (Broadcom4350)
 +Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
 +Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)
 +Brought up 2 CPUs
 +net_namespace: 1140 bytes
 +NET: Registered protocol family 16
 +Total Flash size: 0K with -1 sectors
 +Internal 1P2 VREG will be shutdown if unused...Unused, turn it off (000091ab-000091aa=1<300)
 +registering PCI controller with io_map_base unset
 +registering PCI controller with io_map_base unset
 +bio: create slab <bio-0> at 0
 +SCSI subsystem initialized
 +usbcore: registered new interface driver usbfs
 +usbcore: registered new interface driver hub
 +usbcore: registered new device driver usb
 +pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff]
 +pci 0000:00:00.0: supports D1 D2
 +pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
 +pci 0000:00:00.0: PME# disabled
 +pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
 +pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
 +pci 0000:01:00.0: PME# supported from D0 D3hot
 +pci 0000:01:00.0: PME# disabled
 +pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x007fff]
 +pci 0000:02:00.0: reg 18 64bit mmio: [0x000000-0x1fffff]
 +pci 0000:02:00.0: supports D1 D2
 +pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
 +pci 0000:02:00.0: PME# disabled
 +pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
 +pci 0000:01:00.0:   IO window: disabled
 +pci 0000:01:00.0:   MEM window: 0x11000000-0x112fffff
 +pci 0000:01:00.0:   PREFETCH window: disabled
 +PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:01:00.0 to 64
 +skbFreeTask created successfully
 +BLOG v3.0 Initialized
 +BLOG Rule v1.0 Initialized
 +Broadcom IQoS v0.1 Jul 11 2014 01:55:57 initialized
 +Broadcom GBPM v0.1 Jul 11 2014 01:55:59 initialized
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 4096 (order: 3, 32768 bytes)
 +TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
 +TCP: Hash tables configured (established 4096 bind 4096)
 +TCP reno registered
 +NET: Registered protocol family 1
 +NTFS driver 2.1.29 [Flags: R/O].
 +JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
 +fuse init (API version 7.11)
 +msgmni has been set to 241
 +io scheduler noop registered (default)
 +PCI: Setting latency timer of device 0000:01:00.0 to 64
 +Driver 'sd' needs updating - please use bus_type methods
 +PPP generic driver version 2.4.2
 +PPP Deflate Compression module registered
 +PPP BSD Compression module registered
 +NET: Registered protocol family 24
 +PPPoL2TP kernel driver, V1.0
 +tun: Universal TUN/TAP device driver, 1.6
 +tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
 +bcm963xx_mtd driver v2.0
 +Failed to read image tag from flash
 +Broadcom DSL NAND controller (BrcmNand Controller)
 +-->brcmnand_scan: CS=0, numchips=1, csi=0
 +mtd->oobsize=0, mtd->eccOobSize=0
 +NAND_CS_NAND_XOR=00000000
 +Disabling XOR on CS#0
 +brcmnand_scan: Calling brcmnand_probe for CS=0
 +B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0
 +brcmnand_read_id: CS0: dev_id=92f18095
 +After: NandSelect=40000001, nandConfig=15142200
 +DevId 92f18095 may not be supported.  Will use config info
 +Spare Area Size = 16B/512B
 +Block size=00020000, erase shift=17
 +NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
 +busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
 +timing1 not adjusted: 6574845b
 +timing2 not adjusted: 00001e96
 +brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010
 +ECC level changed to 15
 +OOB size changed to 16
 +BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0
 +
 +Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=92f18095, tim1=6574845b, tim2=00001e96
 +BrcmNAND version = 0x0400 128MB @00000000
 +brcmnand_scan: Done brcmnand_probe
 +brcmnand_scan: B4 nand_select = 40000001
 +brcmnand_scan: After nand_select = 40000001
 +100 CS=0, chip->ctrl->CS[0]=0
 +ECC level 15, threshold at 1 bits
 +reqEccLevel=0, eccLevel=15
 +190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010
 +brcmnand_scan 10
 +200 CS=0, chip->ctrl->CS[0]=0
 +200 chip->ecclevel=15, acc=f7ff1010
 +page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
 +brcmnand_scan 220
 +Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000
 +brcmnand_scan 230
 +brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000
 +brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0
 +ECC layout=brcmnand_oob_bch4_4k
 +brcmnand_scan:  mtd->oobsize=64
 +brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
 +brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
 +300 CS=0, chip->ctrl->CS[0]=0
 +500 chip=878ce990, CS=0, chip->ctrl->CS[0]=0
 +-->brcmnand_default_bbt
 +brcmnand_default_bbt: bbt_td = bbt_main_descr
 +Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0
 +Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0
 +brcmnand_scan 99
 +==> sc_setup_mtd_partitions
 +[sc_setup_mtd_partitions] try read a page at offset = 0x20000
 +[sc_setup_mtd_partitions] read page OK at offset = 0x20000
 +[sc_setup_mtd_partitions] try read a page at offset = 0x40000
 +[sc_setup_mtd_partitions] read page OK at offset = 0x40000
 +mmap flag found on oft = 0x40000
 +[sc_setup_mtd_partitions] try read a page at offset = 0x40800
 +[sc_setup_mtd_partitions] read page OK at offset = 0x40800
 +=====> sc_set_running_rootfs
 +bootflags 1 = eRcOmM.002bootflags 2 = eRcOmM.001set booting from kfs 1
 +<===== sc_set_running_rootfs
 +<== sc_setup_mtd_partitions
 +Creating 12 MTD partitions on "brcmnand.0":
 +0x000000000000-0x000000020000 : "cferom"
 +0x0000000c0000-0x000000200000 : "mmap"
 +0x000000200000-0x000000340000 : "cferam1"
 +0x000000020000-0x0000000c0000 : "cferam2"
 +0x000000340000-0x0000003e0000 : "serial"
 +0x0000003e0000-0x000000520000 : "protect"
 +0x000000520000-0x000003720000 : "rootfs"
 +0x000003720000-0x000006920000 : "rootfs_inactive"
 +0x000006920000-0x000006a60000 : "bootflag1"
 +0x000006a60000-0x000006ba0000 : "bootflag2"
 +0x000006ba0000-0x000006e20000 : "xml_cfg"
 +0x000006e20000-0x0000070a0000 : "app_dat"
 +ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 +PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:00:0a.0 to 64
 +ehci_hcd 0000:00:0a.0: EHCI Host Controller
 +ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
 +ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
 +ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500
 +ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
 +usb usb1: configuration #1 chosen from 1 choice
 +hub 1-0:1.0: USB hub found
 +hub 1-0:1.0: 2 ports detected
 +ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 +PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:00:09.0 to 64
 +ohci_hcd 0000:00:09.0: OHCI Host Controller
 +ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
 +ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600
 +usb usb2: configuration #1 chosen from 1 choice
 +hub 2-0:1.0: USB hub found
 +hub 2-0:1.0: 2 ports detected
 +usbcore: registered new interface driver usblp
 +Initializing USB Mass Storage driver...
 +usbcore: registered new interface driver usb-storage
 +USB Mass Storage support registered.
 +brcmboard: brcm_board_init entry
 +Serial: BCM63XX driver $Revision: 3.00 $
 +ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX
 +ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX
 +Total # RxBds=1448
 +bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
 +
 +bcmPktDma_init: Broadcom Packet DMA Library initialized
 +bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 Jul 11 2014 01:53:11
 +IPSEC SPU: SUCCEEDED 
 +GACT probability NOT on
 +Mirror/redirect action on
 +u32 classifier
 +    input device check on 
 +    Actions configured 
 +Netfilter messages via NETLINK v0.30.
 +nf_conntrack version 0.5.0 (2028 buckets, 8112 max)
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +TCP cubic registered
 +Initializing XFRM netlink socket
 +NET: Registered protocol family 10
 +lo: Disabled Privacy Extensions
 +IPv6 over IPv4 tunneling driver
 +sit0: Disabled Privacy Extensions
 +ip6tnl0: Disabled Privacy Extensions
 +NET: Registered protocol family 17
 +NET: Registered protocol family 15
 +Initializing MCPD Module
 +Ebtables v2.0 registered
 +ebt_time registered
 +ebt_ftos registered
 +ebt_wmm_mark registered
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +VFS: Mounted root (jffs2 filesystem) readonly on device 31:6.
 +Freeing unused kernel memory: 168k freed
 +init started: BusyBox v1.15.3 ()
 +starting pid 271, tty '': '/etc/rcS'
 +mkdir: cannot create directory '/dev/pts': File exists
 +chmod: /var: No such file or directory
 +mkdir: cannot create directory '/var/run': File exists
 +bcm_ingqos: module license 'Proprietary' taints kernel.
 +Disabling lock debugging due to kernel taint
 +Broadcom Ingress QoS Module  Char Driver v0.1 Jul 11 2014 01:50:50 Registered<243>
 +
 +Broadcom Ingress QoS ver 0.1 initialized
 +BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132655B (19MB), num of buffers=9460, buf size=2128
 +Broadcom BPM Module Char Driver v0.1 Jul 11 2014 01:43:59 Registered<244>
 +[NTC bpm] bpm_set_status: BPM status : enabled 
 +
 +NBUFF v1.0 Initialized
 +Initialized fcache state
 +Broadcom Packet Flow Cache  Char Driver v2.2 Jul 11 2014 01:50:54 Registered<242>
 +Created Proc FS /procfs/fcache
 +Broadcom Packet Flow Cache registered with netdev chain
 +Broadcom Packet Flow Cache learning via BLOG enabled.
 +Constructed Broadcom Packet Flow Cache v2.2 Jul 11 2014 01:50:54
 +chipId 0x631680D0
 +Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Jul 11 2014 01:50:17 Registered <241>
 +Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000
 +FAP Soft Reset Done
 +4ke Reset Done
 +Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000
 +FAP Soft Reset Done
 +4ke Reset Done
 +FAP Debug values at 0xa5d9e040 0xa5e1e040
 +Allocated FAP0 GSO Buffers (0xA5DAF0C8) : 1048576 bytes @ 0xA5F00000
 +Allocated FAP1 GSO Buffers (0xA5E2F0C8) : 1048576 bytes @ 0xA5800000
 +Allocated FAP0 TM SDRAM Queue Storage (a5daf0cc) : 341376 bytes @ a5e80000
 +Allocated FAP1 TM SDRAM Queue Storage (a5e2f0cc) : 341376 bytes @ a5900000
 +[NTC fapProto] fapReset  : Reset FAP Protocol layer
 +[FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3968>, free <2688>, total<8192>
 +[FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3968>, free <2688>, total<8192>
 +[FAP0] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576>
 +[FAP1] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576>
 +[FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948
 +[FAP1] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948
 +[FAP0] GSO Buffer set to 0xA5F00000
 +[FAP1] GSO Buffer set to 0xA5800000
 +[FAP0] FAP BPM Initialized.
 +[FAP1] FAP BPM Initialized.
 +fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes
 +fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes
 +bcmPktDma_bind: FAP Driver binding successfull
 +[FAP0] FAP TM: ON
 +[FAP1] FAP TM: ON
 +bcmxtmcfg: bcmxtmcfg_init entry
 +Broadcom BCM63168D0 Ethernet Network Device v0.1 Jul 11 2014 01:52:27
 +Broadcom GMAC Char Driver v0.1 Jul 11 2014 01:52:57 Registered<249>
 +Broadcom GMAC Driver v0.1 Jul 11 2014 01:52:57 Initialized
 +fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000
 +ETH Init: Ch:0 - 200 tx BDs at 0xb0a20650
 +fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000
 +ETH Init: Ch:1 - 200 tx BDs at 0xb0820650
 +fapDrv_psmAlloc: wastage 8 bytes
 +fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184
 +ETH Init: Ch:0 - 600 rx BDs at 0xb0821910
 +fapDrv_psmAlloc: wastage 8 bytes
 +fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184
 +ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910
 +dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered 
 +eth0: MAC Address: 00:0E:8F:XX:XX:XX
 +eth1: MAC Address: 00:0E:8F:XX:XX:XX
 +eth2: MAC Address: 00:0E:8F:XX:XX:XX
 +eth3: MAC Address: 00:0E:8F:XX:XX:XX
 +eth4: MAC Address: 00:0E:8F:XX:XX:XX
 +eth5: MAC Address: 00:0E:8F:XX:XX:XX
 +[NTC arl] arlEnable : Enabled ARL binding to FAP
 +Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Jul 11 2014 01:43:57 Registered <245>
 +Broadcom 802.1Q VLAN Interface, v0.1
 +Endpoint: endpoint_init entry
 +[ERROR ept] boardHalProvInit,104: (ts: 21s 872ms):Charles (104),voiceParamsObtained=0
 +[ERROR ept] boardHalProvInit,122: (ts: 21s 881ms):Charles,boardHalProvInit(122)
 +[ERROR ept] boardHalProvInit,135: (ts: 21s 890ms):Charles,boardHalProvInit(135)
 +BpGetVoiceDectNum(3414),iCnt=0
 +BpGetVoiceDectNum(3415),(*ppBpVoice)->dectChDes[iCnt].status=0
 +BpGetVoiceDectNum(3419),iCnt=0
 +BpGetVoiceDectNum(3419),iCnt=1
 +BpGetVoiceDectNum(3419),iCnt=2
 +BpGetVoiceDectNum(3419),iCnt=3
 +BpGetVoiceParms(3511),numDectLines=4
 +BpGetVoiceParms(3579),i=0,nDeviceCount=0
 +BpGetVoiceParms(3582),i=0, (*ppDc)->voiceDevice[i].nDeviceType=15
 +BpGetVoiceParms(3582),i=1, (*ppDc)->voiceDevice[i].nDeviceType=1
 +Endpoint: endpoint_init COMPLETED
 +ip6_tables: (C) 2000-2006 Netfilter Core Team
 +NComm TMS V6.80 Kernel Module loaded.
 +Success 
 +Success 
 +Success 
 +Success 
 +Success 
 +Success 
 +Note: Loading 6300 MDK (default) driver for 63168 chip 
 +Note: Forcing 53115 driver for 53125 
 +Switch MDK: num_switches = 2
 +Switch MDK: unit = 0; phy_pbmp = 0x8; config_pbmp = 0x48 
 +Switch MDK link poll thread: unit=0; phypbmp=0x8
 +Switch MDK link poll thread: unit=1; phypbmp=0x1f
 +get_run_flag: run flag in /dev/mtd8 is eRcOmM.002
 +get_run_flag: run flag in /dev/mtd9 is eRcOmM.001
 +get_run_flag: run flag in /dev/mtd8 is eRcOmM.002
 +get_run_flag: run flag in /dev/mtd9 is eRcOmM.001
 +get_run_flag: run flag in /dev/mtd8 is eRcOmM.002
 +get_run_flag: run flag in /dev/mtd9 is eRcOmM.001
 +mkdir: cannot create directory '/mnt/appdat/dect': File exists
 +run rc script
 +ADDRCONF(NETDEV_UP): eth0: link is not ready
 +adsl: adsl_init entry
 +adduser: /mnt/shares: File exists
 +
 +=================================
 +rc syslogd start 
 +==================================
 +
 +=================================
 +rc hwim start 
 +==================================
 +
 +=================================
 +rc wanif start 
 +==================================
 +
 +=================================
 +rc lanip start 
 +==================================
 +
 +=================================
 +/usr/sbin/rc radvd restart 
 +==================================
 +killall: radvd: no process killed
 +killall: radvd: no process killed
 +killall: radvd: no process killed
 +
 +=================================
 +/usr/sbin/rc dhcp6s restart 
 +==================================
 +killall: dhcp6s: no process killed
 +killall: dhcp6s: no process killed
 +
 +=================================
 +rc networkmap start 
 +==================================
 +
 +=================================
 +rc telnetd start 
 +==================================
 +
 +=================================
 +rc sshd start 
 +==================================
 +
 +=================================
 +rc dns start 
 +==================================
 +DHCPv6 server start
 +
 +=================================
 +rc ethaccess start 
 +==================================
 +one_opt: dhcp domain = Speedport_W_724V_09011602_00_012
 +one_opt: retry_interval = 300000
 +
 +=================================
 +rc wlan start 
 +==================================
 +
 +=================================
 +rc fw_common start 
 +==================================
 +/usr/sbin/wl: wl driver adapter not found
 +wl: wl driver adapter not found
 +wl: wl driver adapter not found
 +
 +=================================
 +rc firewall6 start basic 
 +==================================
 +
 +=================================
 +rc ntp start 
 +==================================
 +
 +=================================
 +rc igmp_proxy start 
 +==================================
 +
 +=================================
 +rc httpd start 
 +==================================
 +
 +=================================
 +rc cron start 
 +==================================
 +bind: Address already in use
 +
 +=================================
 +rc voip start 
 +==================================
 +
 +=================================
 +rc cpm start 
 +==================================
 +
 +=================================
 +rc tr064 start 
 +==================================
 +
 +=================================
 +rc mediaserver start 
 +==================================
 +starting pid 1439, tty '': '/sbin/getty ttyS0 115200'
 +min_time=1,max_time=5,
 +
 +Speedport login: wl: wl driver adapter not found
 +wl: wl driver adapter not found
 +/usr/sbin/wl: Unsupported
 +/usr/sbin/wl: Unsupported
 +wl1: WLC_GET_VAR(psta_if): Invalid argument
 +wl1: WLC_GET_VAR(psta_if): Invalid argument
 +wl1: WLC_GET_VAR(psta_if): Invalid argument
 +wl1: WLC_GET_VAR(psta_if): Invalid argument
 +CMBS Get Registration HandSet List return OKkillall: wps_det: no process killed
 +
 +=================================
 +/usr/sbin/rc dhcp6s start 
 +==================================
 +DHCPv6 server start
 +/usr/sbin/wl: Unsupported
 +/usr/sbin/wl: Unsupported
 +
 +DECT Encryption Enable
 +
 +=================================
 +/usr/sbin/rc igmp_proxy stop 2 
 +==================================
 +
 +Speedport login: root
 +Welcome to IAD2 CLI, you can type '?' to find usage
 +
 +view @ Speedport> </nowiki>
 +</WRAP>\\
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>BCM63168 128RAM unsupported}}
  • Last modified: 2020/06/10 19:19
  • by danitool