T-Com Speedport W724V Typ C

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR2 SIZ4 SIZ3 SIZ2 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN ro08 SUN2 init clen find flag init clen find flag SUN6 002 002 001 001 RAM1 NAN3 RFS0 NAN5 CFE version 1.0.38-114.185 for BCM963268 (32bit,SP,BE) Build Date: 2014年 02月 28日 星期五 14:56:12 CST (bruce@localhost) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name , id 0x92f1 block 128KB size 131072KB External switch id = 53125 Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 134217728 bytes (128MB) Boot Address: 0xb8000000 read block 1 error find flag begin read flash map Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-26) : 963268MBV Number of MAC Addresses (1-32) : 16 Base MAC Address : 00:0e:8f:xx:xx:xx PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Auxillary File System Size Percent: 0 Main Thread Number [0|1] : 0 Voice Board Configuration (0-5) : LE88266 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Flash Sector Number : 901. *************************************************** Boot Version 1.0.8.0 *************************************************** Entering Firmware : Everything is OK. begin check sum safe value is 255 check sum ok Booting from First image (0xb8520000) ... Decompression OK! Entry at 0x80392f70 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80392f70 Linux version 2.6.30 (root@ubuntu) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Fri Jul 11 02:04:51 CST 2014 BCM Flash API. Flash device is not found. 963268MBV prom init CPU revision is: 0002a080 (Broadcom4350) DSL SDRAM reserved: 0x132000 Determined physical RAM map: memory: 07ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00007ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00007ece On node 0 totalpages: 32462 free_area_init_node: node 0, pgdat 80486130, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 222 pages used for memmap Normal zone: 28144 pages, LIFO batch:7 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32208 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 512 (order: 9, 2048 bytes) console [ttyS0] enabled Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Allocating memory for DSP module core and initialization code Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0 Memory: 123444k/129848k available (3630k kernel code, 6232k reserved, 955k data, 168k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Jul 11 2014 01:35:45 CPU revision is: 0002a080 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 1140 bytes NET: Registered protocol family 16 Total Flash size: 0K with -1 sectors Internal 1P2 VREG will be shutdown if unused...Unused, turn it off (000091ab-000091aa=1<300) registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x007fff] pci 0000:02:00.0: reg 18 64bit mmio: [0x000000-0x1fffff] pci 0000:02:00.0: supports D1 D2 pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:02:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: 0x11000000-0x112fffff pci 0000:01:00.0: PREFETCH window: disabled PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 skbFreeTask created successfully BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Jul 11 2014 01:55:57 initialized Broadcom GBPM v0.1 Jul 11 2014 01:55:59 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 NTFS driver 2.1.29 [Flags: R/O]. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 241 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 PPPoL2TP kernel driver, V1.0 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> bcm963xx_mtd driver v2.0 Failed to read image tag from flash Broadcom DSL NAND controller (BrcmNand Controller) -->brcmnand_scan: CS=0, numchips=1, csi=0 mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0 brcmnand_read_id: CS0: dev_id=92f18095 After: NandSelect=40000001, nandConfig=15142200 DevId 92f18095 may not be supported. Will use config info Spare Area Size = 16B/512B Block size=00020000, erase shift=17 NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff timing1 not adjusted: 6574845b timing2 not adjusted: 00001e96 brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 ECC level changed to 15 OOB size changed to 16 BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0 Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=92f18095, tim1=6574845b, tim2=00001e96 BrcmNAND version = 0x0400 128MB @00000000 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=0, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 brcmnand_scan 220 Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=878ce990, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 brcmnand_scan 99 ==> sc_setup_mtd_partitions [sc_setup_mtd_partitions] try read a page at offset = 0x20000 [sc_setup_mtd_partitions] read page OK at offset = 0x20000 [sc_setup_mtd_partitions] try read a page at offset = 0x40000 [sc_setup_mtd_partitions] read page OK at offset = 0x40000 mmap flag found on oft = 0x40000 [sc_setup_mtd_partitions] try read a page at offset = 0x40800 [sc_setup_mtd_partitions] read page OK at offset = 0x40800 =====> sc_set_running_rootfs bootflags 1 = eRcOmM.002bootflags 2 = eRcOmM.001set booting from kfs 1 <===== sc_set_running_rootfs <== sc_setup_mtd_partitions Creating 12 MTD partitions on "brcmnand.0": 0x000000000000-0x000000020000 : "cferom" 0x0000000c0000-0x000000200000 : "mmap" 0x000000200000-0x000000340000 : "cferam1" 0x000000020000-0x0000000c0000 : "cferam2" 0x000000340000-0x0000003e0000 : "serial" 0x0000003e0000-0x000000520000 : "protect" 0x000000520000-0x000003720000 : "rootfs" 0x000003720000-0x000006920000 : "rootfs_inactive" 0x000006920000-0x000006a60000 : "bootflag1" 0x000006a60000-0x000006ba0000 : "bootflag2" 0x000006ba0000-0x000006e20000 : "xml_cfg" 0x000006e20000-0x0000070a0000 : "app_dat" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmPktDma_init: Broadcom Packet DMA Library initialized bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 Jul 11 2014 01:53:11 IPSEC SPU: SUCCEEDED GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (2028 buckets, 8112 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions ip6tnl0: Disabled Privacy Extensions NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:6. Freeing unused kernel memory: 168k freed init started: BusyBox v1.15.3 () starting pid 271, tty '': '/etc/rcS' mkdir: cannot create directory '/dev/pts': File exists chmod: /var: No such file or directory mkdir: cannot create directory '/var/run': File exists bcm_ingqos: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Broadcom Ingress QoS Module Char Driver v0.1 Jul 11 2014 01:50:50 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132655B (19MB), num of buffers=9460, buf size=2128 Broadcom BPM Module Char Driver v0.1 Jul 11 2014 01:43:59 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Jul 11 2014 01:50:54 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Jul 11 2014 01:50:54 chipId 0x631680D0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Jul 11 2014 01:50:17 Registered <241> Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done FAP Debug values at 0xa5d9e040 0xa5e1e040 Allocated FAP0 GSO Buffers (0xA5DAF0C8) : 1048576 bytes @ 0xA5F00000 Allocated FAP1 GSO Buffers (0xA5E2F0C8) : 1048576 bytes @ 0xA5800000 Allocated FAP0 TM SDRAM Queue Storage (a5daf0cc) : 341376 bytes @ a5e80000 Allocated FAP1 TM SDRAM Queue Storage (a5e2f0cc) : 341376 bytes @ a5900000 [NTC fapProto] fapReset : Reset FAP Protocol layer [FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3968>, free <2688>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3968>, free <2688>, total<8192> [FAP0] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576> [FAP1] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576> [FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948 [FAP1] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948 [FAP0] GSO Buffer set to 0xA5F00000 [FAP1] GSO Buffer set to 0xA5800000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes bcmPktDma_bind: FAP Driver binding successfull [FAP0] FAP TM: ON [FAP1] FAP TM: ON bcmxtmcfg: bcmxtmcfg_init entry Broadcom BCM63168D0 Ethernet Network Device v0.1 Jul 11 2014 01:52:27 Broadcom GMAC Char Driver v0.1 Jul 11 2014 01:52:57 Registered<249> Broadcom GMAC Driver v0.1 Jul 11 2014 01:52:57 Initialized fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000 ETH Init: Ch:0 - 200 tx BDs at 0xb0a20650 fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000 ETH Init: Ch:1 - 200 tx BDs at 0xb0820650 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184 ETH Init: Ch:0 - 600 rx BDs at 0xb0821910 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184 ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth0: MAC Address: 00:0E:8F:XX:XX:XX eth1: MAC Address: 00:0E:8F:XX:XX:XX eth2: MAC Address: 00:0E:8F:XX:XX:XX eth3: MAC Address: 00:0E:8F:XX:XX:XX eth4: MAC Address: 00:0E:8F:XX:XX:XX eth5: MAC Address: 00:0E:8F:XX:XX:XX [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Jul 11 2014 01:43:57 Registered <245> Broadcom 802.1Q VLAN Interface, v0.1 Endpoint: endpoint_init entry [ERROR ept] boardHalProvInit,104: (ts: 21s 872ms):Charles (104),voiceParamsObtained=0 [ERROR ept] boardHalProvInit,122: (ts: 21s 881ms):Charles,boardHalProvInit(122) [ERROR ept] boardHalProvInit,135: (ts: 21s 890ms):Charles,boardHalProvInit(135) BpGetVoiceDectNum(3414),iCnt=0 BpGetVoiceDectNum(3415),(*ppBpVoice)->dectChDes[iCnt].status=0 BpGetVoiceDectNum(3419),iCnt=0 BpGetVoiceDectNum(3419),iCnt=1 BpGetVoiceDectNum(3419),iCnt=2 BpGetVoiceDectNum(3419),iCnt=3 BpGetVoiceParms(3511),numDectLines=4 BpGetVoiceParms(3579),i=0,nDeviceCount=0 BpGetVoiceParms(3582),i=0, (*ppDc)->voiceDevice[i].nDeviceType=15 BpGetVoiceParms(3582),i=1, (*ppDc)->voiceDevice[i].nDeviceType=1 Endpoint: endpoint_init COMPLETED ip6_tables: (C) 2000-2006 Netfilter Core Team NComm TMS V6.80 Kernel Module loaded. Success Success Success Success Success Success Note: Loading 6300 MDK (default) driver for 63168 chip Note: Forcing 53115 driver for 53125 Switch MDK: num_switches = 2 Switch MDK: unit = 0; phy_pbmp = 0x8; config_pbmp = 0x48 Switch MDK link poll thread: unit=0; phypbmp=0x8 Switch MDK link poll thread: unit=1; phypbmp=0x1f get_run_flag: run flag in /dev/mtd8 is eRcOmM.002 get_run_flag: run flag in /dev/mtd9 is eRcOmM.001 get_run_flag: run flag in /dev/mtd8 is eRcOmM.002 get_run_flag: run flag in /dev/mtd9 is eRcOmM.001 get_run_flag: run flag in /dev/mtd8 is eRcOmM.002 get_run_flag: run flag in /dev/mtd9 is eRcOmM.001 mkdir: cannot create directory '/mnt/appdat/dect': File exists run rc script ADDRCONF(NETDEV_UP): eth0: link is not ready adsl: adsl_init entry adduser: /mnt/shares: File exists ================================= rc syslogd start ================================== ================================= rc hwim start ================================== ================================= rc wanif start ================================== ================================= rc lanip start ================================== ================================= /usr/sbin/rc radvd restart ================================== killall: radvd: no process killed killall: radvd: no process killed killall: radvd: no process killed ================================= /usr/sbin/rc dhcp6s restart ================================== killall: dhcp6s: no process killed killall: dhcp6s: no process killed ================================= rc networkmap start ================================== ================================= rc telnetd start ================================== ================================= rc sshd start ================================== ================================= rc dns start ================================== DHCPv6 server start ================================= rc ethaccess start ================================== one_opt: dhcp domain = Speedport_W_724V_09011602_00_012 one_opt: retry_interval = 300000 ================================= rc wlan start ================================== ================================= rc fw_common start ================================== /usr/sbin/wl: wl driver adapter not found wl: wl driver adapter not found wl: wl driver adapter not found ================================= rc firewall6 start basic ================================== ================================= rc ntp start ================================== ================================= rc igmp_proxy start ================================== ================================= rc httpd start ================================== ================================= rc cron start ================================== bind: Address already in use ================================= rc voip start ================================== ================================= rc cpm start ================================== ================================= rc tr064 start ================================== ================================= rc mediaserver start ================================== starting pid 1439, tty '': '/sbin/getty ttyS0 115200' min_time=1,max_time=5, Speedport login: wl: wl driver adapter not found wl: wl driver adapter not found /usr/sbin/wl: Unsupported /usr/sbin/wl: Unsupported wl1: WLC_GET_VAR(psta_if): Invalid argument wl1: WLC_GET_VAR(psta_if): Invalid argument wl1: WLC_GET_VAR(psta_if): Invalid argument wl1: WLC_GET_VAR(psta_if): Invalid argument CMBS Get Registration HandSet List return OKkillall: wps_det: no process killed ================================= /usr/sbin/rc dhcp6s start ================================== DHCPv6 server start /usr/sbin/wl: Unsupported /usr/sbin/wl: Unsupported DECT Encryption Enable ================================= /usr/sbin/rc igmp_proxy stop 2 ================================== Speedport login: root Welcome to IAD2 CLI, you can type '?' to find usage view @ Speedport>