Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:surecom:ep-9600-gp [2015/10/18 15:22] – ↷ Links adapted because of a move operation toh:surecom:ep-9600-gp [2018/02/20 18:51] – ↷ Links adapted because of a move operation bobafetthotmail
Line 1: Line 1:
 +====== Surecom EP-9600-gp ======
 +The Surecom EP-9600-gp is an wireless acccess point with two antennas.
  
 +The board should be the same as [[toh:d-link:dwl-2100ap|D-Link DWL2100AP]]
 +
 +{{page>meta:infobox:construction&noheader&nofooter&noeditbtn}}
 +
 +===== Supported Versions =====
 +^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^
 +| EP-9600-gp A1  |  :?:  | - | Backfire 10.03.1 :?: | - |
 +
 +**NOTE:** Untested: information based on [[toh:d-link:dwl-2100ap|D-Link DWL2100AP]].
 +
 +===== Hardware Highlights =====
 +^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
 +| Atheros AR2313A@ :?: | 16MiB | 4MiB | 1 | No | Yes | Yes |
 +
 +
 +===== Installation =====
 +Please refer to [[toh:d-link:dwl-2100ap|D-Link DWL2100AP]].
 +
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>Instruction set]]:**               | [[wp>MIPS architecture|MIPS]] |
 +| **Vendor:**                               | [[wp>Atheros]] |
 +| **[[docs:techref:bootloader]]:**           | VxWorks |
 +| **[[docs:hardware:soc|System-On-Chip]]:**  | [[docs:hardware:soc:soc.qualcomm.ar5xxx|Atheros AR2313A]] |
 +| **[[docs:hardware:cpu|CPU]] @Frq**         | :?: |
 +| **Flash size:**                 | 4 MB |
 +| **Flash Chip:**                 | [[http://pdf1.alldatasheet.com/datasheet-pdf/view/164984/SPANSION/S29GL032M.html|Spansion S29GL032M90TFIR4]] |
 +| **RAM size:**                   | 16 MB |
 +| **RAM Chip:**                   | [[http://www.esmt.com.tw/DB/manager/upload/M12L128168A.pdf|ESMT M12L128168A]] |
 +| **Wireless:**               | Atheros AR2112A :?: w/ 2 external antennas for 802.11b/g |
 +| **[[docs:hardware:switch]]:**    | [[http://www.icplus.com.tw/pp-IP101A.html|IC+ IP101A]] |
 +| **[[docs:hardware:internet.access.technologies|Modem]]:**   | none |
 +| **USB:**                        | No |
 +| **[[docs:hardware:port.serial|Serial]]:**  | [[#Serial|Yes]] |
 +| **[[docs:hardware:port.jtag|JTAG]]:**      | [[#JTAG|Yes]] |
 +
 +==== Photos ====
 +
 +//Front://
 +
 +{{media:surecom:ep-9600-gp_front.jpg?200|}}
 +
 +//Back://
 +
 +{{media:surecom:ep-9600-gp_back.jpg?200|}}
 +
 +==== Opening the case ====
 +**Note:** This will void your warranty!
 +
 +  *Remove two screws under the AP
 +  *Gently unhook two latches in the front 
 +
 +//Main PCB//
 +
 +{{media:surecom:ep-9600-gp_board.jpg?200|}}
 +
 +==== Serial ====
 +-> [[docs:hardware:port.serial]] general information about the serial port, serial port cable, etc.
 +
 +Serial console could be plugged to JP1: connector lacks, it has to be soldered on the board.
 +
 +For further instructions please refer to the [[toh:d-link:dwl-2100ap#serial|D-link DWL-2100AP]] page.
 +
 +
 +{{media:surecom:ep-9600-gp_serial_jtag.jpg?200|}}
 +
 +
 +The settings are: 9600 bauds, 8 bits, no parity, 1 stop bit (**9600 8N1**)
 +
 +^ terminal configuration ^^
 +| Bits per second   | 9600   |
 +| Data bits         | 8      |
 +| Parity            | None   |
 +| Stop bits         | 1      |
 +| Flow control      | None   |
 +
 +==== JTAG ====
 +-> [[docs:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +Jtag pins are located in J1, but the connector lacks. The pinout and specifications should be the same of [[toh:d-link:dwl-2100ap#serial|D-link DWL-2100AP]]
 +
 +===== Notes =====
 +
 +This Access Point should use the same board as [[toh:d-link:dwl-2100ap|D-link DWL-2100AP]]; so everything on there should also apply to this model.
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>FastEthernet AP 1NIC 1WNIC 16RAM 8Flash Atheros ar5xxx}}
  • Last modified: 2021/01/15 18:26
  • by danitool