Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
toh:surecom:ep-9600-gp [2015/01/16 10:59] – created M3m3nt0toh:surecom:ep-9600-gp [2018/02/20 18:51] – ↷ Links adapted because of a move operation bobafetthotmail
Line 1: Line 1:
 +====== Surecom EP-9600-gp ======
 +The Surecom EP-9600-gp is an wireless acccess point with two antennas.
  
 +The board should be the same as [[toh:d-link:dwl-2100ap|D-Link DWL2100AP]]
 +
 +{{page>meta:infobox:construction&noheader&nofooter&noeditbtn}}
 +
 +===== Supported Versions =====
 +^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^
 +| EP-9600-gp A1  |  :?:  | - | Backfire 10.03.1 :?: | - |
 +
 +**NOTE:** Untested: information based on [[toh:d-link:dwl-2100ap|D-Link DWL2100AP]].
 +
 +===== Hardware Highlights =====
 +^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
 +| Atheros AR2313A@ :?: | 16MiB | 4MiB | 1 | No | Yes | Yes |
 +
 +
 +===== Installation =====
 +Please refer to [[toh:d-link:dwl-2100ap|D-Link DWL2100AP]].
 +
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>Instruction set]]:**               | [[wp>MIPS architecture|MIPS]] |
 +| **Vendor:**                               | [[wp>Atheros]] |
 +| **[[docs:techref:bootloader]]:**           | VxWorks |
 +| **[[docs:hardware:soc|System-On-Chip]]:**  | [[docs:hardware:soc:soc.qualcomm.ar5xxx|Atheros AR2313A]] |
 +| **[[docs:hardware:cpu|CPU]] @Frq**         | :?: |
 +| **Flash size:**                 | 4 MB |
 +| **Flash Chip:**                 | [[http://pdf1.alldatasheet.com/datasheet-pdf/view/164984/SPANSION/S29GL032M.html|Spansion S29GL032M90TFIR4]] |
 +| **RAM size:**                   | 16 MB |
 +| **RAM Chip:**                   | [[http://www.esmt.com.tw/DB/manager/upload/M12L128168A.pdf|ESMT M12L128168A]] |
 +| **Wireless:**               | Atheros AR2112A :?: w/ 2 external antennas for 802.11b/g |
 +| **[[docs:hardware:switch]]:**    | [[http://www.icplus.com.tw/pp-IP101A.html|IC+ IP101A]] |
 +| **[[docs:hardware:internet.access.technologies|Modem]]:**   | none |
 +| **USB:**                        | No |
 +| **[[docs:hardware:port.serial|Serial]]:**  | [[#Serial|Yes]] |
 +| **[[docs:hardware:port.jtag|JTAG]]:**      | [[#JTAG|Yes]] |
 +
 +==== Photos ====
 +
 +//Front://
 +
 +{{media:surecom:ep-9600-gp_front.jpg?200|}}
 +
 +//Back://
 +
 +{{media:surecom:ep-9600-gp_back.jpg?200|}}
 +
 +==== Opening the case ====
 +**Note:** This will void your warranty!
 +
 +  *Remove two screws under the AP
 +  *Gently unhook two latches in the front 
 +
 +//Main PCB//
 +
 +{{media:surecom:ep-9600-gp_board.jpg?200|}}
 +
 +==== Serial ====
 +-> [[docs:hardware:port.serial]] general information about the serial port, serial port cable, etc.
 +
 +Serial console could be plugged to JP1: connector lacks, it has to be soldered on the board.
 +
 +For further instructions please refer to the [[toh:d-link:dwl-2100ap#serial|D-link DWL-2100AP]] page.
 +
 +
 +{{media:surecom:ep-9600-gp_serial_jtag.jpg?200|}}
 +
 +
 +The settings are: 9600 bauds, 8 bits, no parity, 1 stop bit (**9600 8N1**)
 +
 +^ terminal configuration ^^
 +| Bits per second   | 9600   |
 +| Data bits         | 8      |
 +| Parity            | None   |
 +| Stop bits         | 1      |
 +| Flow control      | None   |
 +
 +==== JTAG ====
 +-> [[docs:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +Jtag pins are located in J1, but the connector lacks. The pinout and specifications should be the same of [[toh:d-link:dwl-2100ap#serial|D-link DWL-2100AP]]
 +
 +===== Notes =====
 +
 +This Access Point should use the same board as [[toh:d-link:dwl-2100ap|D-link DWL-2100AP]]; so everything on there should also apply to this model.
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>FastEthernet AP 1NIC 1WNIC 16RAM 8Flash Atheros ar5xxx}}
  • Last modified: 2021/01/15 18:26
  • by danitool