SNR CPE-W4N rev. M

Low cost router that produced in some bodies.

SNR-CPE-W4N rev. M

New design

SNR-CPE-W4N rev. M

Supported Versions

Hardware Highlights

Installation

Original Flash Layout

Layer0 raw flash 8192 KB
Layer1 mtd0 Bootloader 192 KB mtd1 Config 64 KB mtd2 Factory 64 KB mtd6 Kernel_RootFS 7 360 KB mtd5 RW-FS 512 KB
Layer2 mtd3 Kernel_stub 1 041.81 KB mtd4 RootFS_stub 6 318.19 KB

OEM easy installation

Flash by the native uploader in 2 stages:

  1. Use the native uploader to flash an initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by “Administration/Management/Firmware update/Choose File” in vendor's web interface (ip: 192.168.1.10, login: Admin, password: Admin). Wait ~160 seconds.
  2. Flash a sysupgrade image via the initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin file by “System/Backup/Flash Firmware/Flash image...” in LuCI web interface (ip: 192.168.1.1, login: root, no password). Wait ~240 seconds.

OEM installation using the TFTP method

→ generic.flashing.tftp

Specific values needed for tftp

Bootloader tftp server IPv4 address 192.168.1.131
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window approximately 20 seconds
TFTP client required IP address 192.168.1.1

Flash by U-Boot TFTP method:

  1. Configure your PC with IP 192.168.1.131
  2. Set up TFTP server and put the openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin image on your PC
  3. Connect serial port (57600 8N1) and turn on the router. Then interrupt “U-Boot Boot Menu” by hitting 2 key (select “2: Load system code then write to Flash via TFTP.”). Press Y key when show “Warning!! Erase Linux in Flash then burn new one. Are you sure? (Y/N)”. Input device IP (192.168.1.1) ==:192.168.1.1. Input server IP (192.168.1.131) ==:192.168.1.131. Input Linux Kernel filename () ==: openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
  4. Wait ~120 seconds to complete flashing

Upgrading OpenWrt

→ generic.sysupgrade

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Debricking

→ generic.debrick

Failsafe mode

→ failsafe_and_factory_reset

Basic configuration

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
eth0 WAN, LAN ports (1 to 4) None
eth0.1 LAN ports (1 to 4) DHCP
eth0.2 WAN port DHCP
phy0-ap0 WiFi Disabled

Switch Ports

Port Switch port
Internet (WAN) 0
LAN 1 1
LAN 2 2
LAN 3 3
LAN 4 4

Buttons

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The SNR CPE-W4N has the following buttons:

BUTTON Event Pin Active
RST reset GPIO#1 High

LEDs

The SNR CPE-W4N has the following LEDs:

BUTTON Event Pin Active
SYS failsafe, upgrade GPIO#38 Low
WPS running GPIO#39 High
WLAN wlan GPIO#72 Low

Hardware

Info

Opening the case

Note: This will void your warranty!

Main PCB:

Serial

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial connection parameters
for SNR CPE-W4N rev. M 		57600, 8N1, 3.3V

Bootloader mods

→ bootloader

Please choose the operation: 0: Load system code then write to Flash via Serial. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Enter boot command line interface. 7: Load U-Boot code then write to Flash via Serial. 9: Load U-Boot code then write to Flash via TFTP.


Bootlogs

OEM bootlog

U-Boot 1.1.3 (Mar 2 2016 - 14:05:04) Board: MediaTek APSoC DRAM: 64 MB enable ephy clock...done. SSC disabled. MediaTek SPI flash driver, SPI clock: 48MHz spi device id: ef 40 17 0 0 (40170000) find flash: W25Q64BV *** Warning - bad CRC, using default environment ============================================ MediaTek U-Boot Version: 5.0.0.5 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Mar 2 2016 Time:14:05:04 ============================================ icache: sets:512, ways:4, linesz:32, total:65536 dcache: sets:256, ways:4, linesz:32, total:32768 #### The CPU freq = 580 MHZ #### estimate memory size = 64 Mbytes Please choose the operation: 0: Load system code then write to Flash via Serial. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Enter boot command line interface. 7: Load U-Boot code then write to Flash via Serial. 9: Load U-Boot code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Checking image at bc050000 ... Image Name: SNR-CPE-W4N-MT Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 5663406 Bytes = 5.4 MB Load Address: 80000000 Entry Point: 80247580 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80247580) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... DetectRAMsequence MAX memory:[268435456] RAM size detected:[67108864] FullviewRAM:[67108864] Linux version 3.4.111.109 (sfstudio_at_mail.ru@wive-ng.sf.net) (gcc version 4.8.5 (GCC) ) #1 Tue Apr 12 18:55:07 GMT-3 2016 * MediaTek SoC: MT7620N, RevID: 0206, RAM: DDR1, XTAL: 20MHz CPU/OCP/SYS frequency: 580/193/193 MHz CPU revision is: 00019650 (MIPS 24KEc) Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node Early memory PFN ranges 0: 0x00000000 -> 0x00004000 Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,57600n8 root=/dev/mtdblock4 rootfstype=squashfs PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Writing ErrCtl register=00076fdd Readback ErrCtl register=00076fdd Memory: 61784k/65536k available (2388k kernel code, 3752k reserved, 493k data, 188k init, 0k highmem) start_kernel(): bug: interrupts were enabled *very* early, fixing it NR_IRQS:40 console [ttyS0] enabled Calibrating delay loop... 385.02 BogoMIPS (lpj=192512) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 bio: create slab <bio-0> at 0 Switching to clocksource MIPS NET: Registered protocol family 1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) Load Ralink WDG Timer Module squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 120 io scheduler noop registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A Ralink gpio driver initialized Ralink SPI flash driver, SPI clock: 48MHz W25Q64BV (ef 40170000) (8192 Kbytes) Creating 7 MTD partitions on "raspi": 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x00000015473a : "Kernel_stub" 0x00000015473a-0x000000780000 : "RootFS_stub" 0x000000780000-0x000000800000 : "RW-FS" 0x000000050000-0x000000780000 : "Kernel_RootFS" Ralink APSoC Ethernet Driver v3.2.3 (raeth) raeth: PDMA RX ring 256, PDMA TX ring 512. Max packet size 1536 raeth: NAPI support, weight 32 raeth: Byte Queue Limits (BQL) support PPP generic driver version 2.4.2 PPP vpn led has gpio 39 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 8021q: 802.1Q VLAN Support v1.8 NET: Registered protocol family 17 Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 32768 max) gre: GRE over IPv4 demultiplexor driver ip_tables: (C) 2000-2006 Netfilter Core Team TCP: cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 NVRAM: Kernel NVRAM start init. NVRAM: Particion 0 CRC a5fb0865 OK. VFS: Mounted root (squashfs filesystem) readonly on device 31:4. mount /proc file system ok! mount /sys file system ok! mount /dev file system ok! mount /var file system ok! Freeing unused kernel memory: 188k freed Build the /dev/console node. Algorithmics/MIPS FPU Emulator v1.5 INIT Touch mdev. INIT Mount /tmp/rootfs INIT Create some persistent nodes in dev. INIT Init RW particion Start buttons WDG INIT RW File system is ok - preparing. INIT Create start services trees INIT Start services now / # preconfigure >>>>>>>>>>>> NORMAL BOOT <<<<<<<<<<<<<<< preconfigure Factory mac adresess: F8:F0:82:55:04:5C F8:F0:82:55:04:5B F8:F0:82:AD:EF:DC SYSLOG Start klogd SYSLOG Start syslogd local Password for 'Admin' changed Restore time to build time or save time. Tue Apr 12 19:02:00 OMST 2016 raeth: HW IP/TCP/UDP checksum RX/TX offload enabled raeth: HW VLAN TX offload enabled raeth: HW Scatter/Gather TX offload enabled MODULES Loading TV module... TV_MON Starting membd... /var/run/rc0.d/S97tv_membd: line 1: timeout: not found Build config for fist WiFi module. MT76x2 AP Driver version: 3.0.4.0.P1 >>>>> RECONFIGURE WIFI IF = ra0 <<<<<<<<<< Ralink HW NAT v2.52.0 Module Enabled, FoE Size: 16384 c0a865ca 8892 MODULES TV module loaded!


OpenWrt bootlog

U-Boot 1.1.3 (Mar 2 2016 - 14:05:04) Board: MediaTek APSoC DRAM: 64 MB enable ephy clock...done. SSC disabled. MediaTek SPI flash driver, SPI clock: 48MHz spi device id: ef 40 17 0 0 (40170000) find flash: W25Q64BV *** Warning - bad CRC, using default environment ============================================ MediaTek U-Boot Version: 5.0.0.5 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Mar 2 2016 Time:14:05:04 ============================================ icache: sets:512, ways:4, linesz:32, total:65536 dcache: sets:256, ways:4, linesz:32, total:32768 #### The CPU freq = 580 MHZ #### estimate memory size = 64 Mbytes Please choose the operation: 0: Load system code then write to Flash via Serial. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Enter boot command line interface. 7: Load U-Boot code then write to Flash via Serial. 9: Load U-Boot code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Checking image at bc050000 ... Image Name: SNR-CPE-W4N-MT Image Type: MIPS Linux Kernel Image (uncompressed) Data Size: 2181242 Bytes = 2.1 MB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80000000... [ 0.000000] Linux version 5.10.144 (user@debian) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20779+1-c5e167e0d6) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Thu Oct 6 18:24:46 2022 [ 0.000000] Board has DDR1 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is SNR-CPE-W4N (rev.M) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Writing ErrCtl register=000676d9 [ 0.000000] Readback ErrCtl register=000676d9 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 56424K/65536K available (5253K kernel code, 613K rwdata, 1112K rodata, 1204K init, 209K bss, 9112K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.015563] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.087806] pid_max: default: 32768 minimum: 301 [ 0.097188] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.111594] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.129565] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.148538] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.168023] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.181609] pinctrl core: initialized pinctrl subsystem [ 0.193103] NET: Registered protocol family 16 [ 0.267683] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.278756] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.291330] rt2880_gpio 10000638.gpio: registering 16 gpios [ 0.302343] rt2880_gpio 10000638.gpio: registering 16 irq handlers [ 0.314922] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.325758] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.348005] clocksource: Switched to clocksource systick [ 0.359870] NET: Registered protocol family 2 [ 0.368761] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.383859] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.400489] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.415610] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.429619] TCP: Hash tables configured (established 1024 bind 1024) [ 0.442404] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.455319] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.469473] NET: Registered protocol family 1 [ 0.478062] PCI: CLS 0 bytes, default 32 [ 0.491227] rt-timer 10000100.timer: maximum frequency is 1220Hz [ 0.506289] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.524547] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.536052] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.559064] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.572786] printk: console [ttyS0] disabled [ 0.581299] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.600943] printk: console [ttyS0] enabled [ 0.600943] printk: console [ttyS0] enabled [ 0.617504] printk: bootconsole [early0] disabled [ 0.617504] printk: bootconsole [early0] disabled [ 0.647746] spi spi0.0: force spi mode3 [ 0.656880] spi-nor spi0.0: s25fl064k (8192 Kbytes) [ 0.666759] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.679490] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 0.694093] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 0.709230] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 0.723877] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 0.738719] Creating 4 MTD partitions on "spi0.0": [ 0.748333] 0x000000000000-0x000000030000 : "Bootloader" [ 0.762279] 0x000000030000-0x000000040000 : "Config" [ 0.773471] 0x000000040000-0x000000140000 : "Factory" [ 0.786725] 0x000000050000-0x000000800000 : "firmware" [ 0.798593] 2 uimage-fw partitions found on MTD device firmware [ 0.810457] Creating 2 MTD partitions on "firmware": [ 0.820372] 0x000000000000-0x0000002148ba : "kernel" [ 0.830265] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only [ 0.849827] 0x0000002148ba-0x0000007b0000 : "rootfs" [ 0.859813] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 0.880252] mtd: device 5 (rootfs) set to be root filesystem [ 0.891724] 1 squashfs-split partitions found on MTD device rootfs [ 0.904079] 0x000000680000-0x0000007b0000 : "rootfs_data" [ 0.942127] gsw: setting port4 to ephy mode [ 0.950696] mtk_soc_eth 10100000.ethernet: generated random MAC address 22:a1:07:ce:2b:44 [ 0.967021] mtk_soc_eth 10100000.ethernet: no mdio-bus child node found [ 0.980206] mtk_soc_eth 10100000.ethernet: mdio-bus disabled [ 0.991713] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver [ 1.004286] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 1.021460] rt2880_wdt 10000120.watchdog: Initialized [ 1.032899] NET: Registered protocol family 10 [ 1.047792] Segment Routing with IPv6 [ 1.055318] NET: Registered protocol family 17 [ 1.064310] 8021q: 802.1Q VLAN Support v1.8 [ 1.086103] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.107006] Freeing unused kernel memory: 1204K [ 1.116072] This architecture does not have kernel memory protection. [ 1.128921] Run /sbin/init as init process [ 2.165729] init: Console is alive [ 2.173187] init: - watchdog - [ 3.891935] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.132950] usbcore: registered new interface driver usbfs [ 4.144059] usbcore: registered new interface driver hub [ 4.154761] usbcore: registered new device driver usb [ 4.173078] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.190051] ehci-fsl: Freescale EHCI Host controller driver [ 4.203264] ehci-platform: EHCI generic platform driver [ 4.220304] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.235186] ohci-platform: OHCI generic platform driver [ 4.252134] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.271130] init: - preinit - [ 6.025788] random: jshn: uninitialized urandom read (4 bytes read) [ 6.293839] random: jshn: uninitialized urandom read (4 bytes read) [ 6.500148] random: jshn: uninitialized urandom read (4 bytes read) [ 7.551464] 8021q: adding VLAN 0 to HW filter on device eth0 [ 7.754642] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.912643] jffs2: notice: (405) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (5 unchecked, 2 orphan) and 8 of xref (2 dead, 0 orphan) found. [ 8.945695] mount_root: switching to jffs2 overlay [ 8.962742] overlayfs: upper fs does not support tmpfile. [ 8.981876] urandom-seed: Seeding with /etc/urandom.seed [ 9.183698] procd: - early - [ 9.189860] procd: - watchdog - [ 9.620498] procd: - watchdog - [ 9.837477] procd: - ubus - [ 9.978314] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.994394] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.007795] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.030347] procd: - init - Please press Enter to activate this console. [ 11.600571] random: jshn: uninitialized urandom read (4 bytes read) [ 11.658610] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.700558] random: ubus: uninitialized urandom read (4 bytes read) [ 11.985225] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.723792] urngd: jent-rng init failed, err: 2 [ 12.755632] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064 [ 12.770815] Backport generated by backports.git v5.15.58-1-0-g42a95ce7 [ 12.949834] PPP generic driver version 2.4.2 [ 12.963522] NET: Registered protocol family 24 [ 13.016328] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "Factory" [ 13.030819] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected [ 13.046302] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 13.184512] kmodloader: done loading kernel modules from /etc/modules.d/* [ 24.900255] random: crng init done [ 24.907046] random: 87 urandom warning(s) missed due to ratelimiting [ 42.419846] 8021q: adding VLAN 0 to HW filter on device eth0 [ 42.457941] br-lan: port 1(eth0.1) entered blocking state [ 42.468953] br-lan: port 1(eth0.1) entered disabled state [ 42.480135] device eth0.1 entered promiscuous mode [ 42.489729] device eth0 entered promiscuous mode [ 42.579851] br-lan: port 1(eth0.1) entered blocking state [ 42.590687] br-lan: port 1(eth0.1) entered forwarding state [ 43.470912] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.35.0 (2022-10-06 18:24:46 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r20779+49-c5e167e0d6 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


Tags

, , , , , , , , , , , , ,
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1