Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:snr:cpe-me2-lite [2024/12/11 12:15] – [SNR CPE-ME2-Lite] wertwert4pda | toh:snr:cpe-me2-lite [2024/12/11 14:41] – [OEM easy installation] wertwert4pda | ||
|---|---|---|---|
| Line 12: | Line 12: | ||
| {{media: | {{media: | ||
| + | {{media: | ||
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| Line 81: | Line 82: | ||
| -> [[docs: | -> [[docs: | ||
| - | FIXME Please add the installation procedure here. | + | |
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| Line 102: | Line 103: | ||
| <WRAP BOX> | <WRAP BOX> | ||
| - | FIXME //The instructions below are for Broadcom devices and only serve as an example.// | ||
| - | **//Remove / modify them if they do not apply to this particular device!//** | ||
| - | |||
| This section deals with | This section deals with | ||
| * How you install OpenWrt from a device freshly opened | * How you install OpenWrt from a device freshly opened | ||
| Line 110: | Line 108: | ||
| **Note:** Reset router to factory defaults if it has been previously configured. | **Note:** Reset router to factory defaults if it has been previously configured. | ||
| - | | + | |
| - | * Upload | + | **Flash instruction via WEB (old factory firmware 1.10.x)** |
| - | | + | 1. Boot SNR-CPE-ME2-Lite normally with " |
| - | * Telnet to 192.168.1.1 and set a root password, or browse | + | 2. Access |
| + | 3. Select the OpenWrt sysupgrade image in " | ||
| + | | ||
| + | |||
| + | **Note: For new factory firmware (EasyWRT 2.6.x) need downgrade | ||
| + | |||
| </ | </ | ||
| Line 127: | Line 130: | ||
| ^ Bootloader MAC address (special) | ^ Bootloader MAC address (special) | ||
| ^ Firmware tftp image | [[: | ^ Firmware tftp image | [[: | ||
| - | ^ TFTP transfer window | + | ^ TFTP transfer window |
| - | ^ TFTP window start | approximately | + | ^ TFTP window start | approximately |
| - | ^ TFTP client required IP address | + | ^ TFTP client required IP address |
| </ | </ | ||
| Line 137: | Line 140: | ||
| <WRAP BOX> | <WRAP BOX> | ||
| - | |||
| - | FIXME These are generic instructions. Update with your router' | ||
| ==== LuCI Web Upgrade Process ==== | ==== LuCI Web Upgrade Process ==== | ||
| Line 149: | Line 150: | ||
| If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. | If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. | ||
| - | There are two command line methods for upgrading: | ||
| - | |||
| - | * '' | ||
| - | * '' | ||
| Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | ||
| Line 164: | Line 161: | ||
| wget http:// | wget http:// | ||
| sysupgrade / | sysupgrade / | ||
| - | </ | ||
| - | |||
| - | === mtd === | ||
| - | |||
| - | If '' | ||
| - | |||
| - | * Login as root via SSH on 192.168.1.1, | ||
| - | |||
| - | < | ||
| - | cd /tmp | ||
| - | wget http:// | ||
| - | mtd write / | ||
| </ | </ | ||
| Line 244: | Line 229: | ||
| /* =====>>>>> | /* =====>>>>> | ||
| /* When uploading photos, **name them** intelligently. Nobody knows what 20100930_000602.jpg is! */ | /* When uploading photos, **name them** intelligently. Nobody knows what 20100930_000602.jpg is! */ | ||
| - | /* e.g. {{: | + | /* e.g. {{: |
| /* Thanks, your wiki administration - Oct. 2015 */ | /* Thanks, your wiki administration - Oct. 2015 */ | ||
| // | // | ||
| - | **Insert photo of front of the casing** | + | {{: |
| //Back://\\ | //Back://\\ | ||
| - | **Insert photo of back of the casing** | + | {{: |
| //Backside label://\\ | //Backside label://\\ | ||
| - | **Insert photo of backside | + | {{: |
| ==== Opening the case ==== | ==== Opening the case ==== | ||
| Line 261: | Line 246: | ||
| <WRAP BOX> | <WRAP BOX> | ||
| - | FIXME //Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...// | + | |
| - | | + | - Ordered List Item Unscrew the 4 Phillips screws from the bottom of the device. |
| + | - There are 6 latches around the perimeter between the halves of the case. They need to be pressed by inserting | ||
| </ | </ | ||
| + | {{media: | ||
| //Main PCB://\\ | //Main PCB://\\ | ||
| - | **Insert photo of PCB** | + | {{media: |
| + | |||
| + | //Chips on board:// | ||
| + | {{media: | ||
| + | |||
| + | // | ||
| + | {{media: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| Line 272: | Line 266: | ||
| How to connect to the Serial Port of this specific device:\\ | How to connect to the Serial Port of this specific device:\\ | ||
| - | **Insert photo of PCB with markings for serial port** | + | {{: |
| ^ Serial connection parameters\\ for SNR CPE-ME2-Lite rev.B | 57600, 8N1, 3.3V | | ^ Serial connection parameters\\ for SNR CPE-ME2-Lite rev.B | 57600, 8N1, 3.3V | | ||
| Line 280: | Line 274: | ||
| How to connect to the JTAG Port of this specific device:\\ | How to connect to the JTAG Port of this specific device:\\ | ||
| - | **Insert photo of PCB with markings for JTAG port** | + | JTAG not found |
| ===== Bootloader mods ===== | ===== Bootloader mods ===== | ||