Sinovoip BananaPi BPi-R64 V1.1

Bananapi BPi-R64 board

ModelVersionSoCCPU MHzCPU CoresFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemSATA portsUSB
Banana Pi BPi-R64V1.1MT7622AV135028192 eMMC1024MediaTek MT7622AVb/g/n--5-1x SATA31x 3.0

Prepare SD Card:

gzip -cd bananapi_bpi-r64-sdcard.img.gz > /dev/mmcblkX

This card can now be used to boot OpenWrt recovery (==initramfs) as well as production (==with f2fs overlay) system from that card. Install of the bootloader and recovery system to the on-board eMMC can be triggered by setting a bootloader environment variable or by using the bootloader menu accessible via the serial console.

fw_setenv bootcmd run emmc_init

At the next reboot the bootloader on the SD Card will write ARM Trusted Firmware, U-Boot and the OpenWrt recovery image contained on the SD card to the eMMC. You can then switch to boot from eMMC and install a production image using sysupgrade.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget https://downloads.openwrt.org/snapshots/targets/mediatek/mt7622/openwrt-mediatek-mt7622-bananapi_bpi-r64-squashfs-sysupgrade.itb
sysupgrade /tmp/openwrt-mediatek-mt7622-bananapi_bpi-r64-squashfs-sysupgrade.itb

setting a permanent MAC address for Ethernet

Being a development board, the Bananapi BPi-R64 doesn't come with (a) MAC address(es) allocated and assigned by the vendor. Hence it is left to the user to assign a permanent address to the device. If there is a MAC address stored in the U-Boot environment used during boot, this address is used by U-Boot and it is handed down to Linux and becomes the default for all downstream interfaces in OpenWrt as well. To set it from inside OpenWrt, run

fw_setenv ethaddr 02:33:44:55:66:77

and reboot.

The 'factory' button next to the power connector on the board can be used to trigger bootloader environment reset if held down during power on. Once OpenWrt is booting and the LED starts flashing, that button can be used to enter failsafe mode. → failsafe_and_factory_reset

The Sinovoip BananaPi BPi-R64 has the following buttons:

BUTTON Event
Factory reset
WPS ses
Nothing.

Hardware interfaces

port.serial general information about the serial port, serial port cable, etc.

There are a 3.3V TTL level serial port pins marked on the board, see photo above 'TTL debug'

Serial connection parameters
for Sinovoip BananaPi BPi-R64 V1.1
115200, 8N1

F0: 102B 0000 F5: 480A 0031 F5: 480A 0031 F3: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 0400 0041 [0000] G0: 1190 0000 T0: 0000 02D9 [000F] Jump to BL NOTICE: BL2: v2.2(release):OpenWrt v2020-11-09-03017334-7 (mt7622-emmc-2ddr) NOTICE: BL2: Built : 09:54:38, Mar 2 2021 NOTICE: BL2: Booting BL31 NOTICE: BL31: v2.2(release):OpenWrt v2020-11-09-03017334-7 (mt7622-emmc-2ddr) NOTICE: BL31: Built : 09:54:38, Mar 2 2021 pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19 U-Boot 2020.10 (Mar 02 2021 - 09:54:38 +0000) CPU: MediaTek MT7622 Model: mt7622-bpi-r64 DRAM: 1 GiB WDT: Started with servicing (60s timeout) MMC: mmc@11230000: 0, mmc@11240000: 1 Loading Environment from MMC... OK In: serial@11002000 Out: serial@11002000 Err: serial@11002000 Loading Environment from MMC... OK Net: Warning: ethernet@1b100000 (eth0) using random MAC address - 7e:28:52:21:af:ec eth0: ethernet@1b100000 ( ( ( OpenWrt ) ) ) [eMMC] U-Boot 2020.10 (Mar 01 2021 - 19:35:08 +0000) Press UP/DOWN to move, ENTER to select 0. Run default boot command. 1. Boot system via TFTP. 2. Boot production system from eMMC. 3. Boot recovery system from eMMC. 4. Load production system via TFTP then write to eMMC. 5. Load recovery system via TFTP then write to eMMC. 6. Reboot. 7. Reset all settings to factory defaults. U-Boot console Hit any key to stop autoboot: 3  2  1  0 switch to partitions #0, OK mmc0(part 0) is current device MMC read: dev # 0, block # 81920, count 8 ... 8 blocks read: OK MMC read: dev # 0, block # 81920, count 19440 ... 19440 blocks read: OK ## Loading kernel from FIT Image at 4007ff28 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM64 OpenWrt Linux-5.10.18 Type: Kernel Image Compression: gzip compressed Data Start: 0x40080f28 Data Size: 4928456 Bytes = 4.7 MiB Architecture: AArch64 OS: Linux Load Address: 0x44000000 Entry Point: 0x44000000 Hash algo: crc32 Hash value: 4269a8f2 Hash algo: sha1 Hash value: a834d420beaff7c446535af9d1ed035f93cd1515 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 4007ff28 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: ARM64 OpenWrt bananapi_bpi-r64 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x40534f28 Data Size: 25453 Bytes = 24.9 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 2e9dde3b Hash algo: sha1 Hash value: 835fb2ce0fbb87c3f03d0f896a539023bb6caa62 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x40534f28 ## Loading loadables from FIT Image at 4007ff28 ... Trying 'rootfs@1' loadables subimage Description: ARM64 OpenWrt bananapi_bpi-r64 rootfs Type: Filesystem Image Compression: uncompressed Data Start: 0x4053bf28 Data Size: 4988928 Bytes = 4.8 MiB Hash algo: crc32 Hash value: 26f139ea Hash algo: sha1 Hash value: fa4f28d067882d6722a6680987fbb0b65a9b520d Verifying Hash Integrity ... crc32+ sha1+ OK Uncompressing Kernel Image Loading Device Tree to 000000007f7f1000, end 000000007f7fa36c ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.18 (daniel@box) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 8.4.0 r15637+17-7d12f29ae1) 8.4.0, GNU ld (GNU Binutils) 2.34) #0 SMP Mon Mar 1 19:35:08 2021 [ 0.000000] Machine model: Bananapi BPI-R64 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] [ 0.000000] node 0: [mem 0x0000000043030000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] On node 0 totalpages: 262096 [ 0.000000] DMA zone: 4096 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 262096 pages, LIFO batch:63 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 20 pages/cpu s44568 r8192 d29160 u81920 [ 0.000000] pcpu-alloc: s44568 r8192 d29160 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] CPU features: detected: ARM erratum 843419 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258000 [ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512 root=/dev/mmcblk0p5 [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1016820K/1048384K available (7486K kernel code, 848K rwdata, 2112K rodata, 448K init, 292K bss, 31564K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x48c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns [ 0.000003] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns [ 0.008484] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=50000) [ 0.019126] pid_max: default: 32768 minimum: 301 [ 0.024006] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.031678] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.040778] rcu: Hierarchical SRCU implementation. [ 0.045872] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.054128] smp: Bringing up secondary CPUs ... [ 0.059137] Detected VIPT I-cache on CPU1 [ 0.059187] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.059255] smp: Brought up 1 node, 2 CPUs [ 0.074413] SMP: Total of 2 processors activated. [ 0.079284] CPU features: detected: 32-bit EL0 Support [ 0.084605] CPU features: detected: CRC32 instructions [ 0.090047] CPU: All CPU(s) started at EL2 [ 0.094296] alternatives: patching kernel code [ 0.102256] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.112384] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.119500] pinctrl core: initialized pinctrl subsystem [ 0.125388] NET: Registered protocol family 16 [ 0.130721] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.138156] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.146276] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.154818] thermal_sys: Registered thermal governor 'fair_share' [ 0.154826] thermal_sys: Registered thermal governor 'bang_bang' [ 0.161179] thermal_sys: Registered thermal governor 'step_wise' [ 0.167416] thermal_sys: Registered thermal governor 'user_space' [ 0.173918] ASID allocator initialised with 65536 entries [ 0.205904] gpio-499 (asm_sel): hogged as output/high [ 0.223676] SCSI subsystem initialized [ 0.227913] libata version 3.00 loaded. [ 0.232120] usbcore: registered new interface driver usbfs [ 0.237917] usbcore: registered new interface driver hub [ 0.243484] usbcore: registered new device driver usb [ 0.249340] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.260793] clocksource: Switched to clocksource arch_sys_counter [ 0.267798] NET: Registered protocol family 2 [ 0.272715] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.281401] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.289474] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.297059] TCP: Hash tables configured (established 8192 bind 8192) [ 0.303763] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.310639] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.318063] NET: Registered protocol family 1 [ 0.322597] PCI: CLS 0 bytes, default 64 [ 0.327745] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.337176] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.343231] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.386514] mtk-tphy 1a0c4000.usb-phy: failed to get ref_clk(id-1) [ 0.398239] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1 [ 0.413111] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.420612] printk: console [ttyS0] disabled [ 0.425122] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 23, base_baud = 1562500) is a 16550A [ 0.434348] printk: console [ttyS0] enabled [ 0.434348] printk: console [ttyS0] enabled [ 0.442722] printk: bootconsole [uart8250] disabled [ 0.442722] printk: bootconsole [uart8250] disabled [ 0.453173] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 24, base_baud = 1562500) is a 16550A [ 0.462947] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 30, base_baud = 17499995) is a MediaTek BTIF [ 0.472684] serial serial0: tty port ttyS2 registered [ 0.478104] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.487472] loop: module loaded [ 0.493464] libphy: Fixed MDIO Bus: probed [ 0.521349] libphy: mdio: probed [ 0.525249] mtk_soc_eth 1b100000.ethernet: generated random MAC address ce:43:f8:e7:16:80 [ 0.533780] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011860000, irq 39 [ 0.542892] mtk_soc_eth 1b100000.ethernet: generated random MAC address ba:09:2c:09:f1:3e [ 0.551388] mtk_soc_eth 1b100000.ethernet eth1: mediatek frame engine at 0xffffffc011860000, irq 39 [ 0.562210] rtc_mt7622 10212800.rtc: registered as rtc0 [ 0.567503] rtc_mt7622 10212800.rtc: setting system clock to 2021-03-02T20:49:47 UTC (1614718187) [ 0.577728] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 0.588217] mtk-msdc 11240000.mmc: Got CD GPIO [ 0.589038] NET: Registered protocol family 10 [ 0.598499] Segment Routing with IPv6 [ 0.602229] NET: Registered protocol family 17 [ 0.606872] 8021q: 802.1Q VLAN Support v1.8 [ 0.621599] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges: [ 0.628174] mtk-pcie 1a143000.pcie: Parsing ranges property... [ 0.634018] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000 [ 0.701511] mtk-msdc 11230000.mmc: phase: [map:7ffffff] [maxlen:27] [final:9] [ 0.709755] mmc0: new HS200 MMC card at address 0001 [ 0.715980] mmcblk0: mmc0:0001 008G30 7.28 GiB [ 0.721466] mmcblk0boot0: mmc0:0001 008G30 partition 1 4.00 MiB [ 0.728422] mmcblk0boot1: mmc0:0001 008G30 partition 2 4.00 MiB [ 0.734445] mmcblk0rpmb: mmc0:0001 008G30 partition 3 4.00 MiB, chardev (250:0) [ 0.742319] mtk-pcie 1a143000.pcie: Port0 link down [ 0.744166] Alternate GPT is invalid, using primary GPT. [ 0.747419] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00 [ 0.753402] FIT: volume size: 2007040 sectors (1027604480 bytes) [ 0.758741] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.764740] FIT: FDT structure size: 4096 bytes [ 0.770211] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff] [ 0.770215] pci_bus 0000:00: scanning bus [ 0.774765] FIT: Default configuration: config@1 (OpenWrt bananapi_bpi-r64) [ 0.782743] pci_bus 0000:00: fixups for bus [ 0.785632] FIT: kernel sub-image 0x00001000 - 0x004b43c8 'kernel@1' (ARM64 OpenWrt Linux-5.10.18) [ 0.792559] pci_bus 0000:00: bus scan returning with max=00 [ 0.792998] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges: [ 0.796760] FIT: flat_dt sub-image 0x004b5000 - 0x004bb36d 'fdt@1' (ARM64 OpenWrt bananapi_bpi-r64 device tree blob) [ 0.806670] mtk-pcie 1a145000.pcie: Parsing ranges property... [ 0.812219] FIT: filesystem sub-image 0x004bc000 - 0x0097e000 'rootfs@1' (ARM64 OpenWrt bananapi_bpi-r64 rootfs) [ 0.818733] mtk-pcie 1a145000.pcie: MEM 0x0028000000..0x002fffffff -> 0x0028000000 [ 0.830113] FIT: selecting configured loadable rootfs@1 to be root filesystem [ 0.860327] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00 [ 0.861854] mmcblk0: p1 p2 p3 p4 p5(rootfs@1) p6(rootfs_data) p130 [ 0.868012] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.879775] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff] [ 0.886657] pci_bus 0001:00: scanning bus [ 0.890850] pci 0001:00:01.0: [14c3:3258] type 01 class 0x060400 [ 0.896892] pci 0001:00:01.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref] [ 0.905658] pci_bus 0001:00: fixups for bus [ 0.909855] pci 0001:00:01.0: scanning [bus 00-00] behind bridge, pass 0 [ 0.916552] pci 0001:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.924563] pci 0001:00:01.0: scanning [bus 00-00] behind bridge, pass 1 [ 0.931404] pci_bus 0001:01: scanning bus [ 0.935602] pci 0001:01:00.0: [14c3:7615] type 00 class 0x000280 [ 0.941787] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 0.949558] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0001:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 0.977999] pci_bus 0001:01: fixups for bus [ 0.982201] pci_bus 0001:01: bus scan returning with max=01 [ 0.987776] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.994392] pci_bus 0001:00: bus scan returning with max=01 [ 0.999979] pci 0001:00:01.0: BAR 0: no space for [mem size 0x200000000 64bit pref] [ 1.007631] pci 0001:00:01.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref] [ 1.015631] pci 0001:00:01.0: BAR 8: assigned [mem 0x28000000-0x280fffff] [ 1.022418] pci 0001:01:00.0: BAR 0: assigned [mem 0x28000000-0x280fffff 64bit] [ 1.029806] pci 0001:00:01.0: PCI bridge to [bus 01] [ 1.034773] pci 0001:00:01.0: bridge window [mem 0x28000000-0x280fffff] [ 1.041590] pci 0001:00:01.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 1.050145] pci 0001:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 [ 1.058662] pcieport 0001:00:01.0: of_irq_parse_pci: failed with rc=-22 [ 1.065272] pcieport 0001:00:01.0: assign IRQ: got 0 [ 1.070241] pcieport 0001:00:01.0: enabling device (0000 -> 0002) [ 1.076347] pcieport 0001:00:01.0: enabling bus mastering [ 1.082239] mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property [ 1.090514] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered [ 1.134657] libphy: dsa slave smi: probed [ 1.139599] mt7530 mdio-bus:00 wan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL) [ 1.150171] mt7530 mdio-bus:00 lan1 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL) [ 1.160832] mt7530 mdio-bus:00 lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL) [ 1.171465] mt7530 mdio-bus:00 lan3 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL) [ 1.182117] mt7530 mdio-bus:00 lan4 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL) [ 1.192425] mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode [ 1.200012] mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 1.200668] DSA: tree 0 setup [ 1.211128] xhci-mtk 1a0c0000.usb: xHCI Host Controller [ 1.216409] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1 [ 1.225481] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010 [ 1.234574] xhci-mtk 1a0c0000.usb: irq 35, io mem 0x1a0c0000 [ 1.240734] hub 1-0:1.0: USB hub found [ 1.244541] hub 1-0:1.0: 2 ports detected [ 1.248847] xhci-mtk 1a0c0000.usb: xHCI Host Controller [ 1.254092] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2 [ 1.261495] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed [ 1.267814] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.276232] hub 2-0:1.0: USB hub found [ 1.280014] hub 2-0:1.0: 1 port detected [ 1.288938] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 1.296271] Freeing unused kernel memory: 448K [ 1.304904] Run /sbin/init as init process [ 1.308999] with arguments: [ 1.311957] /sbin/init [ 1.314657] with environment: [ 1.317792] HOME=/ [ 1.320141] TERM=linux [ 1.477540] init: Console is alive [ 1.481082] init: - watchdog - [ 1.706270] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 1.750773] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.758057] ehci-fsl: Freescale EHCI Host controller driver [ 1.764478] ehci-platform: EHCI generic platform driver [ 1.771580] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.778473] ohci-platform: OHCI generic platform driver [ 1.785767] mt7622-pinctrl 10211000.pinctrl: invalid function func1 in map table [ 1.793194] mt7622-pinctrl 10211000.pinctrl: invalid function func1 in map table [ 1.800589] mt7622-pinctrl 10211000.pinctrl: invalid function func1 in map table [ 1.808765] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 1.817097] init: - preinit - [ 1.974360] random: fast init done [ 2.059084] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 2.067452] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 2.084883] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode [ 2.092048] 8021q: adding VLAN 0 to HW filter on device lan1 [ 2.106272] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.170766] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 6.178347] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 6.198725] mount_root: loading kmods from internal overlay [ 6.209071] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 6.216269] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 6.405375] block: attempting to load /etc/config/fstab [ 6.410691] block: unable to load configuration (fstab: Entry not found) [ 6.417408] block: no usable configuration [ 6.578103] F2FS-fs (mmcblk0p6): Mounted with checkpoint version = 3f02ec04 [ 6.671516] block: attempting to load /etc/config/fstab [ 6.676852] block: unable to load configuration (fstab: Entry not found) [ 6.683573] block: no usable configuration [ 6.689174] mount_root: switching to f2fs overlay [ 6.696010] overlayfs: "xino" feature enabled using 32 upper inode bits. Failed to find nls_cp437. Maybe it is a built in module ? Failed to find nls_iso8859-1. Maybe it is a built in module ? Failed to find fat. Ma[ 6.718452] /dev/mmcblk0p6: Can't open blockdev ybe it is a built in module ? Failed to find vfat. Maybe it is [ 6.728322] urandom-seed: Seeding with /etc/urandom.seed a built in module ? [ 6.766764] mt7530 mdio-bus:00 lan1: Link is Down [ 6.775976] procd: - early - [ 6.778967] procd: - watchdog - [ 7.314049] procd: - watchdog - [ 7.318909] procd: - ubus - [ 7.342518] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.371814] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.378450] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.386361] procd: - init - Please press Enter to activate this console. [ 7.610252] urngd: v1.0.2 started. [ 7.639430] random: crng init done [ 7.642896] random: 6 urandom warning(s) missed due to ratelimiting [ 7.711071] kmodloader: loading kernel modules from /etc/modules.d/* [ 7.787911] fuse: init (API version 7.32) [ 7.794942] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf [ 7.802558] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2 [ 7.865380] xt_time: kernel timezone is -0000 [ 7.907865] mt7615e 0001:01:00.0: assign IRQ: got 147 [ 7.913006] pci 0001:00:01.0: enabling bus mastering [ 7.918020] mt7615e 0001:01:00.0: enabling device (0000 -> 0002) [ 7.924153] mt7615e 0001:01:00.0: enabling bus mastering [ 7.932454] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 7.955114] mt7622-wmac 18000000.wmac: Invalid MAC address, using random address a2:ad:f8:26:d9:c4 [ 7.965513] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 7.965932] mt7615e 0001:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 7.965932] [ 7.988161] PPP generic driver version 2.4.2 [ 7.993402] NET: Registered protocol family 24 [ 8.001396] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a [ 8.001396] [ 8.034416] kmodloader: done loading kernel modules from /etc/modules.d/* [ 8.045507] mt7615e 0001:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 8.059669] mt7615e 0001:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 8.102375] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931 [ 10.283089] mtk_soc_eth 1b100000.ethernet eth0: Link is Down [ 10.292959] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 10.301318] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 10.311125] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.318250] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode [ 10.325748] 8021q: adding VLAN 0 to HW filter on device lan1 [ 10.336372] br-lan: port 1(lan1) entered blocking state [ 10.341651] br-lan: port 1(lan1) entered disabled state [ 10.350660] device lan1 entered promiscuous mode [ 10.355353] device eth0 entered promiscuous mode [ 10.372511] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode [ 10.380885] 8021q: adding VLAN 0 to HW filter on device lan2 [ 10.389533] br-lan: port 2(lan2) entered blocking state [ 10.394841] br-lan: port 2(lan2) entered disabled state [ 10.401291] device lan2 entered promiscuous mode [ 10.411298] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode [ 10.419053] 8021q: adding VLAN 0 to HW filter on device lan3 [ 10.430013] br-lan: port 3(lan3) entered blocking state [ 10.435315] br-lan: port 3(lan3) entered disabled state [ 10.441362] device lan3 entered promiscuous mode [ 10.450812] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode [ 10.458043] 8021q: adding VLAN 0 to HW filter on device lan4 [ 10.466074] br-lan: port 4(lan4) entered blocking state [ 10.471321] br-lan: port 4(lan4) entered disabled state [ 10.477503] device lan4 entered promiscuous mode [ 10.488445] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode [ 10.495526] 8021q: adding VLAN 0 to HW filter on device wan [ 13.402620] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 13.410151] br-lan: port 1(lan1) entered blocking state [ 13.415385] br-lan: port 1(lan1) entered forwarding state [ 13.421335] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.33.0 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r16065-a8a37d4ea5 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


  • There is currently no way to load the WiFi EEPROM for the built-in IEEE 802.11bgn WiFi of the MT7622AV. Method for loading EEPROM from eMMC (preferably protected hardware partition) needs to be implemented.
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/05/01 18:58
  • by daniel