User Tools

Site Tools


toh:sinovoip:sinovoip_banana_pi_r2

Sinovoip Banana Pi R2

The Banana Pi R2 is a router based development board, which can run on a variety of open source operating systems including OpenWrt, Android, and Bananian. It has 4 Gigabit LAN ports, 1 Gigabit WAN, and 300Mbs wireless N capabilities

  • MediaTek MT7623N, Quad-core ARM Cortex-A7
  • Mali 450 MP4 GPU
  • 2G DDR3 SDRAM
  • 1x Mini PCIE interface
  • 2x SATA interface
  • 4x Gigabit LAN 1x Gigabit WAN

Banana Pi BPI-R2

Supported Versions

Hardware Highlights

VersionSoCCPU MHzCPU CoresFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0Gbit portsUSB
MediaTek MT7623N13004microSD2048MediaTek MT6625Lb/g/na/n52x 3.0, 1x OTG

Installation

Build linux kernel

The openwrt linux binary kernel from the image builder does not find partitions on MTD devices and as a consequence does not start. To do this, you need to rebuild the linux kernel by changing bootloader options.

Download the build system

Configure it in the minimum configuration.Specify board type

  • Target system → MediaTek Ralink ARM
  • Subtarget → MT7623
  • TargetProfile → Bpi Banana Pi R2

You should to enable Build the OpenWrt Image Builder

Configuration

In order to use the original packages from the openwrt repository, you need to enable build the image builder. Also, in the Kernel modules section mark the necessary kernel modules. Binary modules from the repository will not work

Next, you need to change the kernel configuration

$ make kernel_menuconfig

and change the Boot options

  • [*]Use appended device tree blob to zImage (EXPERIMENTAL)
  • [*] Supplement the appended DTB with traditional ATAG information
  • Kernel command line type (Extend with bootloader kernel arguments) —>
  • (vmalloc=496M) Default kernel command string
  • Kernel command line type (Extend bootloader kernel arguments) —>

Boot option configuration

My original kernel was constantly missing the network connection. The following patch solved the problem. The file must be saved in target/linux/mediatek/patches-4.19

diff -ur a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
--- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts	2020-02-17 20:48:50.237176337 +0200
+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts	2020-02-17 20:53:24.700691493 +0200
@@ -111,7 +111,7 @@
 
 	memory@80000000 {
 		device_type = "memory";
-		reg = <0 0x80000000 0 0x80000000>;
+		reg = <0 0x80000000 0 0x40000000>;
 	};
 };

Now is the time to build a new image builder.

$ make -j4

After completion the built image builder will be in bin/targets/mediatek/mt7623/openwrt-imagebuilder-mediatek-mt7623.Linux-x86_64.tar.xz Unpack it, edit the file repositories.conf

## Place your custom repositories here, they must match the architecture and version.
# src/gz %n http://downloads.openwrt.org/snapshots
# src custom file:///usr/src/openwrt/bin/mediatek/packages

## Remote package repositories
src/gz openwrt_core http://downloads.openwrt.org/snapshots/targets/mediatek/mt7623/packages
src/gz openwrt_base http://downloads.openwrt.org/snapshots/packages/arm_cortex-a7_neon-vfpv4/base
src/gz openwrt_luci http://downloads.openwrt.org/snapshots/packages/arm_cortex-a7_neon-vfpv4/luci
src/gz openwrt_packages http://downloads.openwrt.org/snapshots/packages/arm_cortex-a7_neon-vfpv4/packages
src/gz openwrt_routing http://downloads.openwrt.org/snapshots/packages/arm_cortex-a7_neon-vfpv4/routing
src/gz openwrt_telephony http://downloads.openwrt.org/snapshots/packages/arm_cortex-a7_neon-vfpv4/telephony

## This is the local package repository, do not remove!
src imagebuilder file:packages

and build the firmware according to the instructions of the image builder

Installing the bootloader

You will need a micro sd memory card.

Download the bootloader, this requires an original firmware, such as this one https://drive.google.com/drive/folders/1J-1BmMXu-odVWMJNwPsXtaRaLIlGrj6r

You need both files mkt-bpi-r2-SD.img and mtk-bpi-r2-EMMC.img

Install the original firmware according to this instruction http://wiki.banana-pi.org/Getting_Started_with_R2#OpenWrt_On_SD_.26_Emmc_Steps see item 6.

Installing and upgrade OpenWrt firmware

Now the board will have an old firmware version

Upload two files from the image builder folder to the board kernel

build_dir/target-arm_cortex-a7 + neon-vfpv4_musl_eabi/linux-mediatek_mt7623/bpi_bananapi-r2-kernel.bin

and root file system

build_dir/target-arm_cortex-a7 + neon-vfpv4_musl_eabi/linux-mediatek_mt7623/root.squashfs

for example, with the help of scp

scp build_dir/target-arm_cortex-a7 + neon-vfpv4_musl_eabi/linux-mediatek_mt7623/bpi_bananapi-r2-kernel.bin build_dir/target-arm_cortex-a7 + neon-vfpv4_musl_eabi/linux-mediatek_mt7623/root.squashfs root@192.168.1.1:/tmp

Log in via ssh (e.g. putty) at 192.168.1.1 and write them on the EMMC

mtd write /tmp/bpi_bananapi-r2-kernel.bin kernel
mtd write /tmp/root.squashfs rootfs

Flash Layout

https://www.fw-web.de/dokuwiki/lib/exe/detail.php?id=en%3Abpi-r2%3Astorage&media=bpi-r2:boot-structure.png

# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00080000 00010000 "mbr"
mtd1: 00080000 00010000 "uboot"
mtd2: 00080000 00010000 "config"
mtd3: 00080000 00010000 "factory"
mtd4: 02000000 00010000 "kernel"
mtd5: 02000000 00010000 "recovery"
mtd6: 10000000 00010000 "rootfs"
mtd7: 0f5d0000 00010000 "rootfs_data"
mtd8: 1bde00000 00010000 "usrdata"

Upgrading OpenWrt

Perform the update as described in the install section using the mtd program and the kernel and root filesystem image files

LuCI Web Upgrade Process

Does not work. It is not possible to update via the web interface

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan GB LAN*4 192.168.1.1/24
wan GB WAN DHCP

Hardware

Info

General
Brand Sinovoip
Model Banana Pi R2
Versions
Device Type Single Board Computer
Availability Available 2019
Comments - general
OpenWrt Support
Supported Since Commit http://¿
Supported Since Release 18.06.0
Supported Current Release 19.07.4
Unsupported
Hardware
Bootloader U-Boot
Target mediatek
System-On-Chip
CPU MHz 1300
Flash MB microSD
RAM MB 2048
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
Switch MediaTek MT7530WU
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n
WLAN Hardware MediaTek MT6625L
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports 2x 3.0, 1x OTG
SATA ports 2
Serial Yes
JTAG ¿
Comments - USB & SATA ports
Misc
LED count 3
Button count 3
Power supply 12 VDC, 2.0 A
Links
Forum Topic URL
WikiDevi URL https://wikidevi.wi-cat.ru/Banana_Pi_BPI_R2
OEM device homepage URL http://www.banana-pi.com/eacp_view.asp?id=104
Firmware OEM Stock URL http://wiki.banana-pi.org/Banana_Pi_BPI-R2\
Firmware OpenWrt Install URL http://downloads.openwrt.org/releases/19.07.4/targets/mediatek/mt7623/openwrt-19.07.4-mediatek-mt7623-7623n-bananapi-bpi-r2-initramfs-kernel.bin
Firmware OpenWrt Upgrade URL http://downloads.openwrt.org/releases/19.07.4/targets/mediatek/mt7623/openwrt-19.07.4-mediatek-mt7623-7623n-bananapi-bpi-r2-squashfs-sysupgrade.bin
Edit the underlying data View/Edit data

Photos

Main PCB

Main PCB with PCI-E card inserted

Serial

http://wiki.banana-pi.org/File:R2_debug_console.png

Bits per second: 115200

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

Bootlogs

OpenWrt bootlog

[USBD] USB PRB0 LineState: 0 [USBD] USB cable/ No Cable inserted! [PLFM] Keep stay in USB Mode Platform initialization is ok wait for frequency meter finish, CLK26CALI = 0x81 mt_pll_post_init: mt_get_cpu_freq = 1040000Khz wait for frequency meter finish, CLK26CALI = 0x90 mt_pll_post_init: mt_get_bus_freq = 273000Khz wait for frequency meter finish, CLK26CALI = 0x81 mt_pll_post_init: mt_get_mem_freq = 133250Khz [PWRAP] pwrap_init_preloader [PWRAP] pwrap_init [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=0,rdata=2D52 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=1,rdata=2D52 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=2,rdata=2D52 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=3,rdata=800 [PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=4 rdata=5AA5 [PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=5 rdata=5AA5 [PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=6 rdata=5AA5 [PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=7 rdata=5AA5 [PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=8 rdata=5AA5 [PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=9 rdata=5AA5 [PWRAP] _pwrap_init_sistrobe [Read Test] pass,index=10 rdata=5AA5 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=11,rdata=1001 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=12,rdata=B54B [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=13,rdata=B54B [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=14,rdata=B54B [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=15,rdata=B54B [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=16,rdata=B54B [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=17,rdata=B54B [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=18,rdata=B54B [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=19,rdata=2003 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=20,rdata=6A97 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=21,rdata=6A97 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=22,rdata=6A97 [PWRAP] _pwrap_init_sistrobe [Read Test] fail,index=23,rdata=6A97 [PWRAP] _pwrap_init_reg_clock [PMIC_WRAP]wrap_init pass,the return value=0. [pmic6323_init] Preloader Start.................. [pmic6323_init] PMIC CHIP Code = 0x2023 INT_MISC_CON: 0 TOP_RST_MISC: 0 pl pmic powerkey Press [pmic6323_init] powerKey = 1 [pmic6323_init] is USB in = 0xB004 [pmic6323_init] Reg[0x11A]=0x1B pmic setup LED [pmic6323_init] Done................... mt7623 disable long press reset ->>>>> mt7623 disable long press reset <<<<<- mt7623 VPA supplied by 1.0V to MT7530 -> mt7623 VPA supplied by 1.0V to MT7530 <- mt7623 enables RG_VGP1_EN for LCM -> mt7623 enables RG_VGP1_EN for LCM <- MT7623 E2 setting => MT7623 E2 setting <= [PLFM] Init I2C: OK(0) [PLFM] Init PWRAP: OK(0) [PLFM] Init PMIC: OK(0) [PLFM] chip[CA00] [BLDR] [Support SD/eMMC] Build Time: 20180108-211852 ==== Dump RGU Reg ======== RGU MODE: 4D RGU LENGTH: FFE0 RGU STA: 0 RGU INTERVAL: FFF RGU SWSYSRST: 0 ==== Dump RGU Reg End ==== RGU: g_rgu_satus:0 mtk_wdt_mode_config mode value=10, tmp:22000010 PL P ON WDT does not trigger reboot RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3) kpd read addr: 0x0040: data:0x4001 Enter mtk_kpd_gpio_set! kpd debug column : 0, 0, 0, 0, 0, 0, 0, 0 kpd debug row : 0, 0, 0, 0, 0, 0, 0, 0 after set KP enable: KP_SEL = 0x0 ! MTK_PMIC_RST_KEY is used for this project! [RTC] get_frequency_meter: input=0x0, ouput=5 [RTC] get_frequency_meter: input=0x0, ouput=3967 [RTC] get_frequency_meter: input=0x0, ouput=5 [RTC] get_frequency_meter: input=0x0, ouput=0 [RTC] get_frequency_meter: input=0x0, ouput=0 [RTC] bbpu = 0x1, con = 0x8427 rtc_first_boot_init [RTC] get_frequency_meter: input=0x0, ouput=5 [RTC] get_frequency_meter: input=0x0, ouput=3967 [RTC] get_frequency_meter: input=0x0, ouput=5 [RTC] get_frequency_meter: input=0x0, ouput=0 [RTC] get_frequency_meter: input=0x0, ouput=0 rtc_2sec_stat_clear rtc_2sec_reboot_check cali=0 [RTC] irqsta = 0x0, pdn1 = 0x0, pdn2 = 0x201, spar0 = 0xC0, spar1 = 0x800 [RTC] new_spare0 = 0x0, new_spare1 = 0x1, new_spare2 = 0x1, new_spare3 = 0x1 [RTC] bbpu = 0x1, con = 0x426, cali = 0x0 pl pmic powerkey Press power key is pressed [PLFM] Power key boot! [RTC] rtc_bbpu_power_on done [EMI] mcp_dram_num:0,discrete_dram_num:1,enable_combo_dis:0 [EMI] PCDDR3 [Check]mt_get_mdl_number 0x0 [EMI] eMMC/NAND ID = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 [EMI] MDL number = 0 [EMI] emi_set eMMC/NAND ID = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 [EMI][Vcore]0x21E=0x48,0x220=0x48 [EMI][Vmem]0x554=0x0 wait for frequency meter finish, CLK26CALI = 0x81 [EMI] PCDDR3 DRAM Clock = 1600012 KHz, MEMPLL MODE = 2 [EMI] PCDDR3 RXTDN Calibration: Start REXTDN SW calibration... drvp=0xB,drvn=0x8 [EMI] pinmux = 4 =============================================================================== dramc_write_leveling_swcal =============================================================================== delay byte0 byte1 byte2 byte3 ----------------------------- 0 0 0 0 0 1 0 0 0 0 2 0 0 0 0 3 0 1 0 0 4 0 1 0 0 5 0 1 0 0 6 0 1 0 0 7 0 1 0 0 8 0 1 0 0 9 0 1 0 0 10 0 1 0 0 11 0 1 0 0 12 0 1 0 0 13 0 1 0 0 14 0 1 0 0 15 0 1 0 0 pass bytecount = 1 byte_i status best delay 0 1 0 1 2 3 2 1 0 3 1 0 ======================================== [write leveling]DQS: 0x30, DQM: 0x30 [write leveling after remap]DQ byte0 reg: 0x200 val: 0x3333 [write leveling after remap]DQ byte1 reg: 0x204 val: 0x33330000 [write leveling after remap]DQ byte2 reg: 0x208 val: 0x0 [write leveling after remap]DQ byte3 reg: 0x20C val: 0x0 ============================================= X-axis: DQS Gating Window Delay (Fine Scale) Y-axis: DQS Gating Window Delay (Coarse Scale) ============================================= 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0010:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0011:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0012:| 0 0 0 0 1 1 1 1 1 1 1 1 1 0 1 1 0013:| 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0014:| 1 1 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0015:| 1 1 1 1 1 0 0 0 1 0 1 0 1 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Rank 0 coarse tune value selection : 19, 19 19 40 rank 0 coarse = 19 rank 0 fine = 40 00:| 0 0 0 0 0 0 0 0 1 1 1 0 opt_dle value:13 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-31 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 0 0 0 0 0 0 0 0 0 0 10 | 0 0 0 0 0 0 0 0 0 0 20 | 0 0 0 0 0 0 0 0 0 0 30 | 0 0 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =48 DQS1 = 39 DQS2 =53 DQS3 = 45 ================================================================== bit DQS0 bit DQS1 bit DQS2 bit DQS3 0 (23~67)45 8 (10~60)35 16 (23~64)43 24 (18~56)37 1 (24~68)46 9 (13~61)37 17 (24~64)44 25 (18~56)37 2 (24~69)46 10 (13~62)37 18 (31~72)51 26 (21~58)39 3 (21~64)42 11 (16~62)39 19 (23~65)44 27 (21~58)39 4 (24~70)47 12 (17~61)39 20 (31~72)51 28 (25~66)45 5 (24~67)45 13 (16~62)39 21 (26~70)48 29 (20~64)42 6 (25~67)46 14 (16~60)38 22 (27~70)48 30 (20~59)39 7 (27~70)48 15 (16~61)38 23 (32~74)53 31 (21~60)40 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 3 2 2 6 1 3 2 0 4 2 10 | 2 0 0 0 1 1 10 9 2 9 20 | 2 5 5 0 8 8 6 6 0 3 30 | 6 5 ================================================================== *DQIDLY1 = 0x6020203 *DQIDLY2 = 0x20301 *DQIDLY3 = 0x20204 *DQIDLY4 = 0x1010000 *DQIDLY5 = 0x902090A *DQIDLY6 = 0x50502 *DQIDLY7 = 0x6060808 *DQIDLY8 = 0x5060300 *DRAMC_R0DELDLY = 0x2D352730 [MEM]CONA:F3A2,conf1:F07486A3 DM4BitMux = 1 [Warning] DQSO 0 in TX per-bit = 1 > DQSO 0 in WL = 0 DQSO 1 in TX per-bit = 0 <= DQSO 1 in WL = 3 [Warning] DQSO 2 in TX per-bit = 9 > DQSO 2 in WL = 0 [Warning] DQSO 3 in TX per-bit = 6 > DQSO 3 in WL = 0 Tx DQM dly = 0x161 Tx DQM dly bit4 = 0x0 DRAMC_DQODLY1=215767h DRAMC_DQODLY2=57662112h DRAMC_DQODLY3=2211000h DRAMC_DQODLY4=10003023h Tx DQ dly bit4 = 0x0 Tx DQS dly = 0x6931 Tx DQS dly bit4 = 0x0 TX Byte0: DQ - 16, DQS - 15. win_sum= 30 TX Byte1: DQ - 19, DQS - 13. win_sum= 31 TX Byte2: DQ - 8, DQS - 22. win_sum= 29 TX Byte3: DQ - 10, DQS - 22. win_sum= 31 DRAMC calibration takes 650785087 CPU cycles [EMI] DRAMC calibration passed [MEM] complex R/W mem test pass 0:dram_rank_size:80000000 [Dram_Buffer] dram size:-2147483648 [Dram_Buffer] structure size: 1725560 [Dram_Buffer] MAX_TEE_DRAM_SIZE: 0 Load u-boot from eMMC... [PLFM] Init Boot Device: OK(0) [PART] blksz: 512B [PART] [0x0000000000000000-0x000000000003FFFF] "PRELOADER" (512 blocks) [PART] [0x0000000000000000-0x000000000003FFFF] "MBR" (512 blocks) [PART] [0x0000000000040000-0x00000000000BFFFF] "UBOOT" (1024 blocks) [PART] [0x00000000000C0000-0x00000000000FFFFF] "CONFIG" (512 blocks) [PART] [0x0000000000100000-0x000000000013FFFF] "FACTORY" (512 blocks) [PART] [0x0000000000140000-0x000000000213FFFF] "BOOTIMG" (65536 blocks) [PART] [0x0000000002140000-0x000000000413FFFF] "RECOVERY" (65536 blocks) [PART] [0x0000000004140000-0x000000004413FFFF] "ROOTFS" (2097152 blocks) [PART] [0x0000000044140000-0x000001FFC413FFFF] "USER" (-4194304 blocks) [platform_vusb_on] PASS [TOOL] PMIC not dectect usb cable! [TOOL] <UART> listen ended, receive size:0! [TOOL] <UART> wait sync time 150ms->5ms [TOOL] <UART> receieved data: () Device APC domain init setup: bootloader load uboot ,the address of uboot is 81E00000 [PART]partition name UBOOT [PART]partition start block 0x200 [PART]partition size 0x80000 [PART]partition blks 0x400 [PART]partition flags 0x0 [PART]partition name 0x8 [bean] part->startblk(0x200) bdev->blksz(0x200) part->part_id(8) hdr(0xFFB50000) [BlkDev.c 101 ]partition block size 0x200 ,blks:0xE90000 [BlkDev.c 101 ]partition block erase size 0x200 [PART] load "UBOOT" from 0x0000000000050000 (dev) to 0x81E00000 (mem) [SUCCESS] [PART] load speed: 10462KB/s, 300000 bytes, 28ms [BT_SD_PG] device info 0x8590 0x8A00 0xCB01 0x102 0:dram_rank_size:80000000 [PLFM] md_type[0] = 91 [PLFM] md_type[1] = 163 [PLFM] boot reason: 0 [PLFM] boot mode: 0 [PLFM] META COM0: 0 [PLFM] <0xFFB7CC10>: 0x0 [PLFM] boot time: 3053ms [PLFM] DDR reserve mode: enable = 0, success = 0 [BLDR] jump to 0x81E00000 [BLDR] <0x81E00000>=0xEA00000F [BLDR] <0x81E00004>=0xE59FF014 U-Boot (Feb 06 2020 - 12:58:48) g_nr_bank = 1. g_total_rank_size = 0x80000000 DRAM: 2 GiB WARNING: Caches not enabled MMC: emmc: 0, sdcard: 1 booting from eMMC dev_num = 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial bootargs = board=bpi-r2 earlyprintk console=tty1 fbcon=map:0 console=ttyS0,115200 vmalloc=496M debug=7 initcall_debug=0 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait Net: Eth0 Uip activated Hit any key to stop autoboot: 0 dev_num = 0 Device: emmc SD version 1.0 Capacity: 7.3 GiB 7818182656 dev_num = 0 mmc0 is current device dev_num = 0 MMC read: dev # 0, block # 4096, count 24576 ... 24576 blocks read: OK dev_num = 0 Device: emmc SD version 1.0 Capacity: 7.3 GiB 7818182656 bootm flag=0, states=70f ## Booting kernel from Legacy Image at 84000000 ... Image Name: ARM OpenWrt Linux-4.19.106 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2725510 Bytes = 2.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.106 (vanessa@goofy) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12319-083eb80bf2)) #0 SMP PREEMPT Tue Feb 25 16:15:32 2020 [ 0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Bananapi BPI-R2 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] random: get_random_bytes called from start_kernel+0x7c/0x440 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu s30348 r8192 d22900 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 523117 [ 0.000000] Kernel command line: console=ttyS2,115200n8 earlyprintk console=ttyS0,115200 block2mtd.block2mtd=/dev/mmcblk0,65536,RootFs,5 mtdparts=RootFs:512k(mbr)ro,512k(uboot)ro,512k(config)ro,512k(factory)ro,32M(kernel),32M(recovery),256M(rootfs),7168M(usrdata) rootfstype=squashfs,jffs2 vmalloc=496M [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 2068284K/2097148K available (6144K kernel code, 208K rwdata, 1492K rodata, 1024K init, 233K bss, 28864K reserved, 0K cma-reserved, 1564668K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe1000000 - 0xff800000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0800000 ( 520 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (7136 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 209 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 234 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000007] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.000018] Switching to timer-based delay loop, resolution 76ns [ 0.000171] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 147020034397 ns [ 0.000187] sched_clock: 32 bits at 13MHz, resolution 76ns, wraps every 165191050201ns [ 0.000459] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) [ 0.000474] pid_max: default: 32768 minimum: 301 [ 0.000604] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000618] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001252] CPU: Testing write buffer coherency: ok [ 0.060045] Setting up static identity map for 0x80100000 - 0x80100060 [ 0.080043] rcu: Hierarchical SRCU implementation. [ 0.120102] smp: Bringing up secondary CPUs ... [ 0.360593] smp: Brought up 1 node, 4 CPUs [ 0.360606] SMP: Total of 4 processors activated (104.00 BogoMIPS). [ 0.360613] CPU: All CPU(s) started in SVC mode. [ 0.370598] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 3 [ 0.370888] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.370911] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.371104] pinctrl core: initialized pinctrl subsystem [ 0.371820] NET: Registered protocol family 16 [ 0.372121] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.372981] No ATAGs? [ 0.443695] usbcore: registered new interface driver usbfs [ 0.443751] usbcore: registered new interface driver hub [ 0.443817] usbcore: registered new device driver usb [ 0.445063] clocksource: Switched to clocksource arch_sys_counter [ 0.446090] NET: Registered protocol family 2 [ 0.446567] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.446598] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.446641] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.446702] TCP: Hash tables configured (established 4096 bind 4096) [ 0.446804] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.446835] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.447015] NET: Registered protocol family 1 [ 0.448088] No memory allocated for crashlog [ 0.448241] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.452977] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.452990] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.468162] bounce: pool size: 64 pages [ 0.468185] io scheduler noop registered [ 0.468194] io scheduler deadline registered (default) [ 0.474678] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.495823] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 194, base_baud = 1625000) is a ST16650V2 [ 0.516396] 11003000.serial: ttyS1 at MMIO 0x11003000 (irq = 195, base_baud = 1625000) is a ST16650V2 [ 0.536929] 11004000.serial: ttyS2 at MMIO 0x11004000 (irq = 196, base_baud = 1625000) is a ST16650V2 [ 1.038772] console [ttyS2] enabled [ 1.042759] mtk_rng 1020f000.rng: registered RNG driver [ 1.042905] random: fast init done [ 1.051576] random: crng init done [ 1.051902] loop: module loaded [ 1.058787] mt6323-regulator mt6323-regulator: Chip ID = 0x2023 [ 1.074708] libphy: Fixed MDIO Bus: probed [ 1.101840] libphy: mdio: probed [ 1.105247] mt7530 mdio-bus:00: Linked as a consumer to regulator.6 [ 1.111523] mt7530 mdio-bus:00: Linked as a consumer to regulator.17 [ 1.118049] mt7530 mdio-bus:00: Dropping the link to regulator.17 [ 1.124153] mt7530 mdio-bus:00: Dropping the link to regulator.6 [ 1.130195] mtk_soc_eth 1b100000.ethernet: generated random MAC address c2:2f:e3:9d:b6:b6 [ 1.138826] mtk_soc_eth 1b100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY] [ 1.149567] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xe10e0000, irq 207 [ 1.158015] netif_napi_add() called with weight 256 on device [ 1.164504] xhci-mtk 1a1c0000.usb: Linked as a consumer to regulator.3 [ 1.171071] xhci-mtk 1a1c0000.usb: Linked as a consumer to regulator.2 [ 1.177778] xhci-mtk 1a1c0000.usb: xHCI Host Controller [ 1.182983] xhci-mtk 1a1c0000.usb: new USB bus registered, assigned bus number 1 [ 1.193436] xhci-mtk 1a1c0000.usb: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010 [ 1.202482] xhci-mtk 1a1c0000.usb: irq 204, io mem 0x1a1c0000 [ 1.208921] hub 1-0:1.0: USB hub found [ 1.212678] hub 1-0:1.0: 1 port detected [ 1.216928] xhci-mtk 1a1c0000.usb: xHCI Host Controller [ 1.222122] xhci-mtk 1a1c0000.usb: new USB bus registered, assigned bus number 2 [ 1.229490] xhci-mtk 1a1c0000.usb: Host supports USB 3.0 SuperSpeed [ 1.235789] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.244284] hub 2-0:1.0: USB hub found [ 1.248053] hub 2-0:1.0: 1 port detected [ 1.252430] xhci-mtk 1a240000.usb: Linked as a consumer to regulator.3 [ 1.259014] xhci-mtk 1a240000.usb: Linked as a consumer to regulator.2 [ 1.265713] xhci-mtk 1a240000.usb: xHCI Host Controller [ 1.270920] xhci-mtk 1a240000.usb: new USB bus registered, assigned bus number 3 [ 1.281356] xhci-mtk 1a240000.usb: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010 [ 1.290407] xhci-mtk 1a240000.usb: irq 205, io mem 0x1a240000 [ 1.296799] hub 3-0:1.0: USB hub found [ 1.300549] hub 3-0:1.0: 1 port detected [ 1.304772] xhci-mtk 1a240000.usb: xHCI Host Controller [ 1.309993] xhci-mtk 1a240000.usb: new USB bus registered, assigned bus number 4 [ 1.317355] xhci-mtk 1a240000.usb: Host supports USB 3.0 SuperSpeed [ 1.323637] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.332143] hub 4-0:1.0: USB hub found [ 1.335915] hub 4-0:1.0: 1 port detected [ 1.340245] i2c /dev entries driver [ 1.345175] mtk-thermal 1100b000.thermal: Device not calibrated, using default calibration values [ 1.354674] mtk-wdt 10007000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 1.362773] cpu cpu0: Linked as a consumer to regulator.4 [ 1.368191] cpu cpu0: dummy supplies not allowed for exclusive requests [ 1.376118] sdhci: Secure Digital Host Controller Interface driver [ 1.382248] sdhci: Copyright(c) Pierre Ossman [ 1.387355] mtk-msdc 11230000.mmc: Linked as a consumer to regulator.2 [ 1.394024] mtk-msdc 11230000.mmc: Linked as a consumer to regulator.1 [ 1.426541] mtk-msdc 11240000.mmc: Got CD GPIO [ 1.431198] mtk-msdc 11240000.mmc: Linked as a consumer to regulator.2 [ 1.462734] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.473599] NET: Registered protocol family 10 [ 1.478942] Segment Routing with IPv6 [ 1.482633] NET: Registered protocol family 17 [ 1.483042] mmc0: new high speed MMC card at address 0001 [ 1.492488] 8021q: 802.1Q VLAN Support v1.8 [ 1.496752] ThumbEE CPU extension supported. [ 1.500991] Registering SWP/SWPB emulation handler [ 1.503327] mmcblk0: mmc0:0001 8WPD3R 7.28 GiB [ 1.510932] mmcblk0boot0: mmc0:0001 8WPD3R partition 1 4.00 MiB [ 1.517460] mmcblk0boot1: mmc0:0001 8WPD3R partition 2 4.00 MiB [ 1.523438] mmcblk0rpmb: mmc0:0001 8WPD3R partition 3 512 KiB, chardev (250:0) [ 1.554551] mtk-pcie 1a140000.pcie: PCI host bridge to bus 0000:00 [ 1.560717] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0x1a160000-0x1a16ffff]) [ 1.570138] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.576972] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.584576] PCI: bus0: Fast back to back transfers disabled [ 1.590127] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.598087] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.608033] PCI: bus1: Fast back to back transfers disabled [ 1.613712] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 1.615266] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-mtk [ 1.627708] pci 0000:02:00.0: reg 0x14: initial BAR value 0x00000000 invalid [ 1.634711] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid [ 1.641726] pci 0000:02:00.0: reg 0x1c: initial BAR value 0x00000000 invalid [ 1.648741] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid [ 1.657500] PCI: bus2: Fast back to back transfers disabled [ 1.663071] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.669826] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 1.677004] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 1.683737] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 1.690913] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 1.697661] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 1.704396] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff] [ 1.710455] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x6007ffff 64bit] [ 1.717729] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] [ 1.724892] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.729830] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.736575] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 1.743744] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref] [ 1.750920] pci 0000:02:00.0: BAR 5: assigned [mem 0x60200000-0x602001ff] [ 1.757668] pci 0000:02:00.0: BAR 4: assigned [io 0x1000-0x100f] [ 1.763715] pci 0000:02:00.0: BAR 0: assigned [io 0x1010-0x1017] [ 1.769773] pci 0000:02:00.0: BAR 2: assigned [io 0x1018-0x101f] [ 1.775833] pci 0000:02:00.0: BAR 1: assigned [io 0x1020-0x1023] [ 1.781880] pci 0000:02:00.0: BAR 3: assigned [io 0x1024-0x1027] [ 1.787937] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.792860] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff] [ 1.798921] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 1.805667] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 1.812989] pcieport 0000:00:00.0: enabling device (0140 -> 0142) [ 1.819202] pcieport 0000:00:00.0: Signaling PME with IRQ 217 [ 1.825009] pcieport 0000:00:00.0: AER enabled with IRQ 217 [ 1.830735] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 1.836903] pcieport 0000:00:01.0: Signaling PME with IRQ 218 [ 1.842717] pcieport 0000:00:01.0: AER enabled with IRQ 218 [ 1.848532] mt7530 mdio-bus:00: Linked as a consumer to regulator.6 [ 1.854809] mt7530 mdio-bus:00: Linked as a consumer to regulator.17 [ 1.895008] hub 2-1:1.0: USB hub found [ 1.898867] hub 2-1:1.0: 4 ports detected [ 2.016036] libphy: dsa slave smi: probed [ 2.020188] mt7530 mdio-bus:00 wan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 2.029024] mt7530 mdio-bus:00 lan0 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 2.035084] usb 1-1: new high-speed USB device number 2 using xhci-mtk [ 2.037838] mt7530 mdio-bus:00 lan1 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] [ 2.052510] mt7530 mdio-bus:00 lan2 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] [ 2.061300] mt7530 mdio-bus:00 lan3 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] [ 2.072293] DSA: tree 0 setup [ 2.075777] mtd: RootFs: partitioning exceeds flash size, truncating [ 2.082080] 8 cmdlinepart partitions found on MTD device RootFs [ 2.088121] Creating 8 MTD partitions on "RootFs": [ 2.092874] 0x000000000000-0x000000080000 : "mbr" [ 2.098109] 0x000000080000-0x000000100000 : "uboot" [ 2.103389] 0x000000100000-0x000000180000 : "config" [ 2.108775] 0x000000180000-0x000000200000 : "factory" [ 2.114238] 0x000000200000-0x000002200000 : "kernel" [ 2.119661] 0x000002200000-0x000004200000 : "recovery" [ 2.125257] 0x000004200000-0x000014200000 : "rootfs" [ 2.130635] mtd: device 6 (rootfs) set to be root filesystem [ 2.136866] 1 squashfs-split partitions found on MTD device rootfs [ 2.143001] 0x000004c30000-0x000014200000 : "rootfs_data" [ 2.148855] 0x000014200000-0x0001d2000000 : "usrdata" [ 2.154309] block2mtd: mtd0: [RootFs] erase_size = 64KiB [65536] [ 2.160443] hctosys: unable to open rtc device (rtc0) [ 2.168225] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 2.176356] Freeing unused kernel memory: 1024K [ 2.180958] Run /sbin/init as init process [ 2.228263] hub 1-1:1.0: USB hub found [ 2.232163] hub 1-1:1.0: 4 ports detected [ 2.417741] init: Console is alive [ 2.421863] init: - watchdog - [ 2.575111] usb 1-1.1: new full-speed USB device number 3 using xhci-mtk [ 2.825134] usb 1-1.2: new full-speed USB device number 4 using xhci-mtk [ 2.864746] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.905621] SCSI subsystem initialized [ 2.915806] ahci 0000:02:00.0: enabling device (0140 -> 0143) [ 2.921613] ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled [ 2.928305] ahci 0000:02:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl IDE mode [ 2.936357] ahci 0000:02:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs [ 2.945685] scsi host0: ahci [ 2.958947] scsi host1: ahci [ 2.961967] ata1: SATA max UDMA/133 abar m512@0x60200000 port 0x60200100 irq 218 [ 2.969375] ata2: SATA max UDMA/133 abar m512@0x60200000 port 0x60200180 irq 218 [ 3.085083] usb 1-1.3: new full-speed USB device number 5 using xhci-mtk [ 3.306493] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.951806] ata1.00: ATA-8: WDC WD5000BPVT-22HXZT1, 01.01A01, max UDMA/133 [ 4.958649] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 32), AA [ 5.006754] ata1.00: configured for UDMA/133 [ 5.021407] scsi 0:0:0:0: Direct-Access ATA WDC WD5000BPVT-2 1A01 PQ: 0 ANSI: 5 [ 5.030313] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 5.037765] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 5.042993] sd 0:0:0:0: [sda] Write Protect is off [ 5.047841] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.072317] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.356486] ata2: SATA link down (SStatus 0 SControl 300) [ 5.374550] usbcore: registered new interface driver usb-storage [ 5.380688] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.397260] init: - preinit - [ 5.899788] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode [ 5.906470] IPv6: ADDRCONF(NETDEV_UP): lan1: link is not ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.028677] mount_root: loading kmods from internal overlay [ 10.044386] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 10.052912] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 13.167489] jffs2: notice: (170) jffs2_build_xattr_subsystem: complete building xattr subsystem, 37 of xdatum (3 unchecked, 34 orphan) and 211 of xref (38 dead, 123 orphan) found. [ 13.183782] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 13.194076] block: extroot: not configured [ 13.300946] jffs2: notice: (168) jffs2_build_xattr_subsystem: complete building xattr subsystem, 37 of xdatum (3 unchecked, 34 orphan) and 211 of xref (38 dead, 123 orphan) found. [ 13.384301] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 13.392005] block: extroot: not configured [ 13.435736] mount_root: switching to jffs2 overlay [ 13.449381] overlayfs: upper fs does not support tmpfile. [ 13.458365] urandom-seed: Seeding with /etc/urandom.seed [ 13.520128] procd: - early - [ 13.523041] procd: - watchdog - Failed to connect to ubus [ 14.176077] procd: - watchdog - [ 14.180024] procd: - ubus - [ 14.233684] procd: - init - Please press Enter to activate this console. [ 14.561380] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.569616] tun: Universal TUN/TAP device driver, 1.6 [ 14.581679] usbcore: registered new interface driver cdc_acm [ 14.587439] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 14.595493] urngd: v1.0.2 started. [ 14.596073] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc [ 14.606565] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51 [ 14.620273] usblp 1-1.1:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1D17 [ 14.631647] usblp 1-1.2:1.0: usblp1: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x0924 pid 0x423B [ 14.860716] usblp 1-1.3:1.0: usblp2: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04B8 pid 0x007C [ 14.870875] usbcore: registered new interface driver usblp [ 14.877725] usbcore: registered new interface driver usbserial_generic [ 14.884260] usbserial: USB Serial support registered for generic [ 14.893832] xt_time: kernel timezone is -0000 [ 14.934504] usbcore: registered new interface driver mt76x2u [ 14.948514] PPP generic driver version 2.4.2 [ 14.964630] usbcore: registered new interface driver option [ 14.970517] usbserial: USB Serial support registered for GSM modem (1-port) [ 14.983202] ath9k 0000:01:00.0: enabling device (0140 -> 0142) [ 14.989291] ath: phy0: WB335 1-ANT card detected [ 14.993879] ath: phy0: Set BT/WLAN RX diversity capability [ 15.006869] ath: phy0: Enable LNA combining [ 15.023161] ieee80211 phy0: Atheros AR9565 Rev:1 mem=0xe1780000, irq=217 [ 15.030288] kmodloader: done loading kernel modules from /etc/modules.d/* [ 15.333353] EXT4-fs (sda): mounted filesystem with ordered data mode. Opts: [ 16.825474] mt7530 mdio-bus:00 lan0: configuring for phy/gmii link mode [ 16.832601] br-lan: port 1(lan0) entered blocking state [ 16.837882] br-lan: port 1(lan0) entered disabled state [ 16.843703] device lan0 entered promiscuous mode [ 16.848447] device eth0 entered promiscuous mode [ 16.856264] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 16.864594] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode [ 16.871817] br-lan: port 2(lan1) entered blocking state [ 16.877168] br-lan: port 2(lan1) entered disabled state [ 16.883262] device lan1 entered promiscuous mode [ 16.890777] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode [ 16.897968] br-lan: port 3(lan2) entered blocking state [ 16.903199] br-lan: port 3(lan2) entered disabled state [ 16.909578] device lan2 entered promiscuous mode [ 16.916730] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode [ 16.923795] br-lan: port 4(lan3) entered blocking state [ 16.929085] br-lan: port 4(lan3) entered disabled state [ 16.935486] device lan3 entered promiscuous mode [ 16.946010] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode [ 16.952805] IPv6: ADDRCONF(NETDEV_UP): wan: link is not ready [ 17.425716] ath: EEPROM regdomain: 0x835e [ 17.429699] ath: EEPROM indicates we should expect a country code [ 17.436785] ath: doing EEPROM country->regdmn map search [ 17.442073] ath: country maps to regdmn code: 0x56 [ 17.446898] ath: Country alpha2 being used: VE [ 17.451318] ath: Regpair used: 0x56 [ 17.455185] ath: regdomain 0x835e dynamically updated by user [ 18.615311] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 18.624141] br-lan: port 5(wlan0) entered blocking state [ 18.629508] br-lan: port 5(wlan0) entered disabled state [ 18.635232] device wlan0 entered promiscuous mode [ 18.761366] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 18.768088] br-lan: port 5(wlan0) entered blocking state [ 18.773365] br-lan: port 5(wlan0) entered forwarding state [ 18.779125] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 21.115612] mt7530 mdio-bus:00 lan3: Link is Up - 1Gbps/Full - flow control rx/tx [ 21.123081] br-lan: port 4(lan3) entered blocking state [ 21.128283] br-lan: port 4(lan3) entered forwarding state [ 32.475149] vusb: disabling [ 32.477939] vmc: disabling [ 32.480626] vmch: disabling [ 32.483400] vgp1: disabling [ 32.486297] vcamaf: disabling


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/sinovoip/sinovoip_banana_pi_r2.txt · Last modified: 2020/10/22 10:13 by pcryan