Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:sim:simax1800t [2024/07/23 23:18] – [Debricking] stevescottoh:sim:simax1800t [2024/12/13 09:45] – [Specific Configuration] frollic
Line 7: Line 7:
 <WRAP center round important 60%> <WRAP center round important 60%>
 **This Device have multiple brand, but come from the same OEM, OEM may minor change hardware in the future** **This Device have multiple brand, but come from the same OEM, OEM may minor change hardware in the future**
-</WRAP> 
  
-30$ AX1800 routerwith MT7621 dual core CPU with 256MB RAM+**Haier HAR-20S2U1 = EDUP EP-RT2960 AX1800 = fenvi AX1800 = SIM SIMAX1800T (but different casing)** 
 + 
 +**EDUP userssee the warning in the [[:toh:sim:simax1800t#flash_layout|Flash layout]] section** 
 +</WRAP>
  
 /*****/ /*****/
Line 17: Line 19:
 {{media:oem-ax1800.png?200|Generic Router}} {{media:oem-ax1800.png?200|Generic Router}}
  
-Haier HAR-20S2U1 = EDUP EP-RT2960 AX1800 = fenvi AX1800 = SIM SIMAX1800T (but different shell) +**Forum link** https://forum.openwrt.org/t/edup-ep-rt2960-ax1800-strange-openwrt-router/198933
- +
-**relate forum** https://forum.openwrt.org/t/edup-ep-rt2960-ax1800-strange-openwrt-router/198933+
 ===== Supported Versions ===== ===== Supported Versions =====
 <!-- ToH: { <!-- ToH: {
Line 93: Line 93:
  
 ==== Flash Layout ==== ==== Flash Layout ====
-<WRAP BOX> +:!EDUP version has two flash firmware partitions (firmware and firmware2) these are a different size to the other models and cause problems. Deleting them and creating partitions of the right size was required after uploading images of the wrong size.
-FIXME //[[:docs:techref:flash.layout#discovery_how_to_find_out|Find out flash layout]], then add the flash layout table here (copy, paste, modify the [[docs:techref:flash.layout#partitioning_of_the_flash|example]]).// +
- +
-Please check out the article [[docs:techref:flash.layout|Flash layout]]. It contains examples and explanations that describe how to document the flash layout. +
-</WRAP> +
- +
-Note, edup version has two flash firmware partitions (firmware and firmware2) these are a different size to the other models and cause problems. Deleting them and creating partitions of the right size was required after uploading images of the wrong size. +
-==== OEM easy installation ==== +
- +
-<WRAP BOX> +
-FIXME //The instructions below are for Broadcom devices and only serve as an example.//\\ +
-**//Remove / modify them if they do not apply to this particular device!//** +
- +
-This section deals with +
-  * How you install OpenWrt from a device freshly opened +
-  * The steps required such as reset to factory defaults if the device has already been configured +
- +
-**Note:** Reset router to factory defaults if it has been previously configured. +
-  * Browse to ''<nowiki>http://192.168.1.1/Upgrade.asp</nowiki>'' +
-  * Upload .bin file to router +
-  * Wait for it to reboot +
-  * Telnet to 192.168.1.1 and set a root password, or browse to ''<nowiki>http://192.168.1.1</nowiki>'' if LuCI is installed. +
-</WRAP>+
  
 ==== OEM installation using the TFTP method ==== ==== OEM installation using the TFTP method ====
Line 179: Line 157:
 Set up your Internet connection, configure wireless, configure USB port, etc. Set up your Internet connection, configure wireless, configure USB port, etc.
  
-===== Specific Configuration ===== 
- 
-<WRAP BOX> 
-FIXME Please fill in real values for this device, then remove the EXAMPLEs 
- 
-==== Network interfaces ==== 
-The default network configuration is: 
-^ Interface Name   ^ Description                  ^ Default configuration    ^ 
-| br-lan           | EXAMPLE LAN & WiFi           | EXAMPLE 192.168.1.1/24   | 
-| vlan0 (eth0.0)   | EXAMPLE LAN ports (1 to 4)   | EXAMPLE None             | 
-| vlan1 (eth0.1)   | EXAMPLE WAN port             | EXAMPLE DHCP             | 
-| wl0              | EXAMPLE WiFi                 | EXAMPLE Disabled         | 
- 
-</WRAP> 
  
 ==== Switch Ports (for VLANs) ==== ==== Switch Ports (for VLANs) ====
Line 657: Line 621:
  
 ===== Tags ===== ===== Tags =====
-<WRAP BOX> 
-FIXME //Add tags below, then remove this fixme.// 
-</WRAP> 
  
-[[meta:tags|How to add tags]] +{{tag>MT7621}} {{tag>256RAM}} {{tag>128Flash}} {{tag>GigabitEthernet}} {{tag>wlan}} {{tag>802.11ax}} {{tag>802.11abgn}} {{tag>NonDetachableAntenna}}
-{{tag>EXAMPLETAG}}+
  • Last modified: 2024/12/13 09:59
  • by frollic