Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:sim:simax1800t [2024/07/23 20:41] – added tftp server required and client ip details along with timing stevescot | toh:sim:simax1800t [2024/12/13 09:45] – [Specific Configuration] frollic | ||
|---|---|---|---|
| Line 7: | Line 7: | ||
| <WRAP center round important 60%> | <WRAP center round important 60%> | ||
| **This Device have multiple brand, but come from the same OEM, OEM may minor change hardware in the future** | **This Device have multiple brand, but come from the same OEM, OEM may minor change hardware in the future** | ||
| - | </ | ||
| - | 30$ AX1800 | + | **Haier HAR-20S2U1 = EDUP EP-RT2960 |
| + | |||
| + | **EDUP users, see the warning in the [[: | ||
| + | </ | ||
| /*****/ | /*****/ | ||
| Line 17: | Line 19: | ||
| {{media: | {{media: | ||
| - | Haier HAR-20S2U1 = EDUP EP-RT2960 AX1800 = fenvi AX1800 = SIM SIMAX1800T (but different shell) | + | **Forum link** https:// |
| - | + | ||
| - | **relate forum** https:// | + | |
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| <!-- ToH: { | <!-- ToH: { | ||
| Line 93: | Line 93: | ||
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| - | <WRAP BOX> | + | :!: EDUP version has two flash firmware partitions |
| - | FIXME //[[:docs:techref: | + | |
| - | + | ||
| - | Please check out the article [[docs: | + | |
| - | </ | + | |
| - | + | ||
| - | ==== OEM easy installation ==== | + | |
| - | + | ||
| - | <WRAP BOX> | + | |
| - | FIXME //The instructions below are for Broadcom devices | + | |
| - | **//Remove / modify | + | |
| - | + | ||
| - | This section deals with | + | |
| - | * How you install OpenWrt from a device freshly opened | + | |
| - | * The steps required | + | |
| - | + | ||
| - | **Note:** Reset router to factory defaults if it has been previously configured. | + | |
| - | * Browse to ''< | + | |
| - | * Upload .bin file to router | + | |
| - | * Wait for it to reboot | + | |
| - | * Telnet to 192.168.1.1 and set a root password, or browse to ''< | + | |
| - | </ | + | |
| ==== OEM installation using the TFTP method ==== | ==== OEM installation using the TFTP method ==== | ||
| Line 170: | Line 149: | ||
| -> [[docs: | -> [[docs: | ||
| + | Connecting to the internal serial port can allow changes to be made to partitions (mtd commands) and flashing through tftp by a connected tftp server. | ||
| ===== Failsafe mode ===== | ===== Failsafe mode ===== | ||
| -> [[docs: | -> [[docs: | ||
| Line 177: | Line 157: | ||
| Set up your Internet connection, configure wireless, configure USB port, etc. | Set up your Internet connection, configure wireless, configure USB port, etc. | ||
| - | ===== Specific Configuration ===== | ||
| - | |||
| - | <WRAP BOX> | ||
| - | FIXME Please fill in real values for this device, then remove the EXAMPLEs | ||
| - | |||
| - | ==== Network interfaces ==== | ||
| - | The default network configuration is: | ||
| - | ^ Interface Name ^ Description | ||
| - | | br-lan | ||
| - | | vlan0 (eth0.0) | ||
| - | | vlan1 (eth0.1) | ||
| - | | wl0 | EXAMPLE WiFi | EXAMPLE Disabled | ||
| - | |||
| - | </ | ||
| ==== Switch Ports (for VLANs) ==== | ==== Switch Ports (for VLANs) ==== | ||
| Line 655: | Line 621: | ||
| ===== Tags ===== | ===== Tags ===== | ||
| - | <WRAP BOX> | ||
| - | FIXME //Add tags below, then remove this fixme.// | ||
| - | </ | ||
| - | [[meta: | + | {{tag>MT7621}} {{tag> |
| - | {{tag>EXAMPLETAG}} | + | |