Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:qxwlan:e750g [2018/08/07 07:39] – created zhangsd20 | toh:qxwlan:e750g [2018/09/12 01:08] – [Qxwlan E750G V8] zhangsd20 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | {{: | + | ====== Qxwlan E750G V8====== |
| + | {{: | ||
| + | |||
| + | ====== Important notice ====== | ||
| + | |||
| + | <color # | ||
| + | data at the end. You should not use v2 images on v1 board because it | ||
| + | will result in lost of ART data!</ | ||
| + | |||
| + | ====== Supported Versions ====== | ||
| + | ---- datatable ---- | ||
| + | cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | ||
| + | headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data | ||
| + | align : c, | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | |||
| + | ====== Hardware Highlights ====== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | ||
| + | header | ||
| + | align : c, | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | |||
| + | ====== Installation ====== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| + | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| + | align : l,c,c | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | ====== U-boot controller ====== | ||
| + | |||
| + | U-Boot 1.1.4 (Jun 27 2018 - 11: | ||
| + | |||
| + | AR9344 U-Boot for E750G | ||
| + | |||
| + | DRAM: 128 MB DDR2 32-bit | ||
| + | FLASH: | ||
| + | |||
| + | LED on during eth initialization... | ||
| + | |||
| + | eth0 up | ||
| + | eth0 | ||
| + | Setting 0xb8116290 to 0xc0802d0f | ||
| + | Hit any key to stop autobooting: | ||
| + | ath> | ||
| + | |||
| + | ====== Upgrading firmware ====== | ||
| + | |||
| + | Flash instruction (using U-Boot CLI and tftp server): | ||
| + | |||
| + | 1. Configure PC with static IP 192.168.1.10 and tftp server. | ||
| + | |||
| + | 2. Rename " | ||
| + | tftp server directory. | ||
| + | |||
| + | 3. Connect PC with one of RJ45 ports, power up the board and press " | ||
| + | key to access U-Boot CLI. | ||
| + | |||
| + | 4. Use the following command to update the device to OpenWrt: "run lfw" | ||
| + | |||
| + | Flash instruction (using U-Boot web-based recovery): | ||
| + | |||
| + | 1. Configure PC with static IP 192.168.1.xxx(2-254)/ | ||
| + | |||
| + | 2. Connect PC with one of RJ45 ports, press the reset button, | ||
| + | power up the board and keep button pressed for around 6-7 seconds, | ||
| + | until LEDs start flashing. | ||
| + | |||
| + | 3. Open your browser and enter 192.168.1.1, | ||
| + | and click the upgrade button. | ||
| + | |||
| + | ====== Default FLASH Layout ====== | ||
| + | ,, | ||
| + | m25p80 spi0.0: found s25fl064k, expected m25p80 | ||
| + | m25p80 spi0.0: s25fl064k (8192 Kbytes) | ||
| + | 7 cmdlinepart partitions found on MTD device spi0.0 | ||
| + | '' | ||
| + | |||
| + | ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ||
| + | | mtd0 | 0x000000000000 | 0x000000040000 | 0x00040000 | 0x00010000 | u-boot | | ||
| + | | mtd1 | 0x000000040000 | 0x000000050000 | 0x00010000 | 0x00010000 | u-boot-env | | ||
| + | | mtd2 | 0x000000050000 | 0x000000060000 | 0x00010000 | 0x00010000 | pri-data | | ||
| + | | mtd3 | 0x000000060000 | 0x000000070000 | 0x00010000 | 0x00010000 | art | | ||
| + | | mtd4 | 0x000000700000 | 0x0000001D0000 | 0x00160000 | 0x00010000 | kernel | | ||
| + | | mtd5 | 0x0000001D0000 | 0x000000800000 | 0x00630000 | 0x00010000 | rootfs | ||
| + | | mtd6 | 0x000000070000 | 0x000000800000 | 0x00790000 | 0x00010000 | firmware | | ||
| + | |||
| + | ====== photos ====== | ||
| + | {{: | ||
| + | ====== Hardware ====== | ||
| + | |||
| + | ===== Info ===== | ||
| + | ^ [[wp> | ||
| + | ^ [[docs: | ||
| + | ^ [[docs: | ||
| + | ^ [[docs: | ||
| + | ^ Flash size | 8 MB NOR-Flash | | ||
| + | ^ RAM | 128 MB DDR2 RAM | | ||
| + | ^ Wireless | ||
| + | ^ Ethernet | ||
| + | ^ Antenna | ||
| + | ^ PCIE | 1x miniPCIE | | ||
| + | ^ [[docs: | ||
| + | ^ LED | Standard Ethernet LED's, WIFI LED | | ||
| + | ^ Hardware buttons | reset button | | ||
| + | ^ Power | 1x DC jack for main power input (12-48V) | | ||
| + | ^ Board Size | 120 x 74x 16mm (L x W x H) | | ||
| + | |||
| + | ===== Specification ===== | ||
| + | |||
| + | * 560/450/225 MHz (CPU/ | ||
| + | * 64/128 MB of RAM (DDR2) | ||
| + | * 8/16 MB of FLASH (SPI NOR) | ||
| + | * 2T2R 2.4 GHz (AR9344) | ||
| + | * 1x 10/100 Mbps, 1x 10/100/1000 Ethernet (one port support POE) | ||
| + | * 7x LED (1x RGB, 6 driven by GPIO) | ||
| + | * 1x button (reset) | ||
| + | * 1x miniPCIE slot | ||
| + | * 1x DC jack for main power input (12-48V) | ||
| + | * UART (J23), USB, LEDs header on PCB | ||
| + | |||
| + | ===== Board Photos Info ====== | ||
| + | | ||
| + | |||
| + | 115200 8N1, no hardware flow control. | ||
| + | {{: | ||