Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:qxwlan:e600gac [2018/07/02 01:03] – zhangsd20 | toh:qxwlan:e600gac [2018/09/12 10:31] – Section heading levels corrected, some cleanup tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Qxwlan E600GAC V2====== | ====== Qxwlan E600GAC V2====== | ||
| - | {{: | + | {{: |
| - | ====== Important notice ===== | + | |
| - | <color # | + | ===== Important notice ==== |
| - | data at the end. You should not use v2 images on v1 board because it | + | |
| - | will result in lost of ART data!</ | + | |
| - | ====== Supported Versions | + | <color # |
| + | |||
| + | ===== Supported Versions ===== | ||
| ---- datatable ---- | ---- datatable ---- | ||
| cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | ||
| Line 16: | Line 15: | ||
| - | ====== Hardware Highlights | + | ===== Hardware Highlights ===== |
| ---- datatable ---- | ---- datatable ---- | ||
| cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | ||
| Line 25: | Line 24: | ||
| - | ====== Installation | + | ===== Installation ===== |
| ---- datatable ---- | ---- datatable ---- | ||
| cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| Line 33: | Line 32: | ||
| ---- | ---- | ||
| - | ====== Upgrading firmware ====== | ||
| Flash instruction (using U-Boot CLI and tftp server): | Flash instruction (using U-Boot CLI and tftp server): | ||
| 1. Configure PC with static IP 192.168.1.10 and tftp server. | 1. Configure PC with static IP 192.168.1.10 and tftp server. | ||
| - | | + | 2. Rename |
| - | | + | 3. Connect PC with one of RJ45 ports, power up the board and press " |
| - | tftp server directory. | + | |
| - | | + | |
| - | 3. Connect PC with one of RJ45 ports, power up the board and press | + | |
| - | " | + | |
| - | + | ||
| 4. Use the following command to update the device to OpenWrt: "run lfw". | 4. Use the following command to update the device to OpenWrt: "run lfw". | ||
| Flash instruction (using U-Boot web-based recovery): | Flash instruction (using U-Boot web-based recovery): | ||
| 1. Configure PC with static IP 192.168.1.xxx(2-254)/ | 1. Configure PC with static IP 192.168.1.xxx(2-254)/ | ||
| - | | + | 2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. |
| - | | + | 3. Open your browser and enter 192.168.1.1, |
| - | power up the board and keep button pressed for around 6-7 seconds, | + | |
| - | until LEDs start flashing. | + | ===== U-boot controller ===== |
| - | + | ||
| - | 3. Open your browser and enter 192.168.1.1, | + | U-Boot 1.1.4 (Jun 27 2018 - 11: |
| - | image and click the upgrade button. | + | |
| + | E600G (QCA953X) U-Boot | ||
| + | |||
| + | DRAM: 16bit ddr2 128 MB | ||
| + | FLASH: | ||
| + | |||
| + | LED on during eth initialization... | ||
| + | |||
| + | eth0 up | ||
| + | eth0 | ||
| + | Setting 0x181162c0 to 0x68d02100 | ||
| + | Hit any key to stop autoboot: | ||
| + | ath> | ||
| + | |||
| + | |||
| + | |||
| + | ===== Default FLASH Layout ===== | ||
| - | ====== Default FLASH Layout ====== | ||
| - | ,, | ||
| m25p80 spi0.0: found w25q128, expected m25p80 | m25p80 spi0.0: found w25q128, expected m25p80 | ||
| m25p80 spi0.0: w25q128 (16384 Kbytes) | m25p80 spi0.0: w25q128 (16384 Kbytes) | ||
| 7 cmdlinepart partitions found on MTD device spi0.0 | 7 cmdlinepart partitions found on MTD device spi0.0 | ||
| - | '' | ||
| ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ||
| Line 72: | Line 78: | ||
| | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | ||
| - | ====== photos ===== | ||
| - | {{: | ||
| - | ====== Hardware | + | ===== Hardware ===== |
| ==== Info ==== | ==== Info ==== | ||
| ^ [[wp> | ^ [[wp> | ||
| - | ^ [[docs: | + | ^ [[docs: |
| ^ [[docs: | ^ [[docs: | ||
| ^ [[docs: | ^ [[docs: | ||
| Line 93: | Line 97: | ||
| ^ Board Size | 85 x 85x 16mm (L x W x H) | | ^ Board Size | 85 x 85x 16mm (L x W x H) | | ||
| - | ====== Specification | + | ==== Specification ==== |
| * 650/391/216 MHz (CPU/ | * 650/391/216 MHz (CPU/ | ||
| Line 101: | Line 105: | ||
| * 2x 10/100 Mbps Ethernet (one port with PoE support) | * 2x 10/100 Mbps Ethernet (one port with PoE support) | ||
| * 5x LED (4 driven by GPIO) | * 5x LED (4 driven by GPIO) | ||
| - | * 1x button (reset) | ||
| - | * 1x DC jack for main power input (9-48 V) | ||
| * UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB | * UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB | ||
| - | ====== | + | ==== Photos |
| - | | + | {{: |
| + | {{: | ||
| + | |||
| + | ==== Serial | ||
| + | Serial connection settings: | ||
| - | 115200 8N1, no hardware flow control. | ||
| {{: | {{: | ||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||