Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:qxwlan:e600gac [2018/06/22 03:28] – zhangsd20 | toh:qxwlan:e600gac [2018/09/12 10:31] – Section heading levels corrected, some cleanup tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Qxwlan E600GAC V2====== | ||
| + | {{: | ||
| + | |||
| + | ===== Important notice ==== | ||
| + | |||
| + | <color # | ||
| + | |||
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| ---- datatable ---- | ---- datatable ---- | ||
| Line 6: | Line 13: | ||
| filter | filter | ||
| ---- | ---- | ||
| + | |||
| + | |||
| + | ===== Hardware Highlights ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | ||
| + | header | ||
| + | align : c, | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | |||
| + | ===== Installation ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| + | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| + | align : l,c,c | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | |||
| + | Flash instruction (using U-Boot CLI and tftp server): | ||
| + | 1. Configure PC with static IP 192.168.1.10 and tftp server. | ||
| + | 2. Rename '' | ||
| + | 3. Connect PC with one of RJ45 ports, power up the board and press " | ||
| + | 4. Use the following command to update the device to OpenWrt: "run lfw". | ||
| + | |||
| + | Flash instruction (using U-Boot web-based recovery): | ||
| + | 1. Configure PC with static IP 192.168.1.xxx(2-254)/ | ||
| + | 2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. | ||
| + | 3. Open your browser and enter 192.168.1.1, | ||
| + | |||
| + | ===== U-boot controller ===== | ||
| + | |||
| + | U-Boot 1.1.4 (Jun 27 2018 - 11: | ||
| + | |||
| + | E600G (QCA953X) U-Boot | ||
| + | | ||
| + | DRAM: 16bit ddr2 128 MB | ||
| + | FLASH: | ||
| + | | ||
| + | LED on during eth initialization... | ||
| + | | ||
| + | eth0 up | ||
| + | eth0 | ||
| + | Setting 0x181162c0 to 0x68d02100 | ||
| + | Hit any key to stop autoboot: | ||
| + | ath> | ||
| + | |||
| + | |||
| + | |||
| + | ===== Default FLASH Layout ===== | ||
| + | |||
| + | m25p80 spi0.0: found w25q128, expected m25p80 | ||
| + | m25p80 spi0.0: w25q128 (16384 Kbytes) | ||
| + | 7 cmdlinepart partitions found on MTD device spi0.0 | ||
| + | |||
| + | ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ||
| + | | mtd0 | 0x000000000000 | 0x000000040000 | 0x00040000 | 0x00010000 | u-boot | | ||
| + | | mtd1 | 0x000000040000 | 0x000000050000 | 0x00010000 | 0x00010000 | u-boot-env | | ||
| + | | mtd2 | 0x000000050000 | 0x000000060000 | 0x00010000 | 0x00010000 | pri-data | | ||
| + | | mtd3 | 0x000000060000 | 0x000000070000 | 0x00010000 | 0x00010000 | art | | ||
| + | | mtd4 | 0x000000700000 | 0x0000001D0000 | 0x00160000 | 0x00010000 | kernel | | ||
| + | | mtd5 | 0x0000001D0000 | 0x000001000000 | 0x00e30000 | 0x00010000 | rootfs | ||
| + | | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | ||
| + | |||
| + | |||
| + | ===== Hardware ===== | ||
| + | |||
| + | ==== Info ==== | ||
| + | ^ [[wp> | ||
| + | ^ [[docs: | ||
| + | ^ [[docs: | ||
| + | ^ [[docs: | ||
| + | ^ Flash size | 16 MB NOR-Flash | | ||
| + | ^ RAM | 128 MB DDR2 RAM | | ||
| + | ^ Wireless | ||
| + | ^ Ethernet | ||
| + | ^ Antenna | ||
| + | ^ [[docs: | ||
| + | ^ LED | Standard Ethernet LED's, WIFI LED | | ||
| + | ^ Hardware buttons | reset button | | ||
| + | ^ Power | 1x DC jack for main power input (9-48 V) | | ||
| + | ^ Board Size | 85 x 85x 16mm (L x W x H) | | ||
| + | |||
| + | ==== Specification ==== | ||
| + | |||
| + | * 650/391/216 MHz (CPU/ | ||
| + | * 64/128 MB of RAM (DDR2) | ||
| + | * 8/16 MB of FLASH (SPI NOR) | ||
| + | * 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601) | ||
| + | * 2x 10/100 Mbps Ethernet (one port with PoE support) | ||
| + | * 5x LED (4 driven by GPIO) | ||
| + | * UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB | ||
| + | |||
| + | ==== Photos ==== | ||
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | ==== Serial ==== | ||
| + | Serial connection settings: 115200 8N1, no hardware flow control. | ||
| + | |||
| + | {{: | ||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||