Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:qxwlan:e600g [2018/07/02 02:06] – zhangsd20 | toh:qxwlan:e600g [2018/09/12 08:34] – Section heading levels corrected, some cleanup tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Qxwlan E600G V2====== | ====== Qxwlan E600G V2====== | ||
| - | {{: | + | {{: |
| - | ====== Important notice | + | ===== Important notice ===== |
| - | <color # | + | <color # |
| - | data at the end. You should not use v2 images on v1 board because it | + | |
| - | will result in lost of ART data!</ | + | |
| - | ====== Supported Versions | + | ===== Supported Versions ===== |
| ---- datatable ---- | ---- datatable ---- | ||
| cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | ||
| Line 17: | Line 15: | ||
| - | ====== Hardware Highlights | + | ===== Hardware Highlights ===== |
| ---- datatable ---- | ---- datatable ---- | ||
| cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | ||
| Line 26: | Line 24: | ||
| - | ====== Installation | + | ===== Installation ===== |
| ---- datatable ---- | ---- datatable ---- | ||
| cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| - | align : | + | align : |
| filter | filter | ||
| ---- | ---- | ||
| - | ====== U-boot controller | + | Flash instruction (using U-Boot CLI and tftp server): |
| + | |||
| + | - Configure PC with static IP 192.168.1.10 and tftp server. | ||
| + | - Rename '' | ||
| + | - Connect PC with one of RJ45 ports, power up the board and press " | ||
| + | - Use the following command to update the device to OpenWrt: '' | ||
| + | |||
| + | Flash instruction (using U-Boot web-based recovery): | ||
| + | |||
| + | - Configure PC with static IP 192.168.1.xxx(2-254)/ | ||
| + | - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. | ||
| + | - Open your browser and enter 192.168.1.1, | ||
| + | |||
| + | ===== U-boot controller ===== | ||
| U-Boot 1.1.4 (Jun 27 2018 - 11: | U-Boot 1.1.4 (Jun 27 2018 - 11: | ||
| - | E600G (QCA95xX) U-Boot | + | E600G (QCA953X) U-Boot |
| | | ||
| DRAM: 16bit ddr2 128 MB | DRAM: 16bit ddr2 128 MB | ||
| Line 51: | Line 62: | ||
| ath> | ath> | ||
| - | ====== Upgrading firmware ====== | ||
| - | Flash instruction (using U-Boot CLI and tftp server): | + | ===== Default FLASH Layout ===== |
| - | + | ||
| - | 1. Configure PC with static IP 192.168.1.10 and tftp server. | + | |
| - | + | ||
| - | 2. Rename " | + | |
| - | tftp server directory. | + | |
| - | + | ||
| - | 3. Connect PC with one of RJ45 ports, power up the board and press " | + | |
| - | key to access U-Boot CLI. | + | |
| - | + | ||
| - | 4. Use the following command to update the device to OpenWrt: "run lfw" | + | |
| - | + | ||
| - | Flash instruction (using U-Boot web-based recovery): | + | |
| - | + | ||
| - | 1. Configure PC with static IP 192.168.1.xxx(2-254)/ | + | |
| - | + | ||
| - | 2. Connect PC with one of RJ45 ports, press the reset button, | + | |
| - | power up the board and keep button pressed for around 6-7 seconds, | + | |
| - | until LEDs start flashing. | + | |
| - | + | ||
| - | 3. Open your browser and enter 192.168.1.1, | + | |
| - | and click the upgrade button. | + | |
| - | ====== Default FLASH Layout ====== | ||
| - | ,, | ||
| m25p80 spi0.0: found w25q128, expected m25p80 | m25p80 spi0.0: found w25q128, expected m25p80 | ||
| m25p80 spi0.0: w25q128 (16384 Kbytes) | m25p80 spi0.0: w25q128 (16384 Kbytes) | ||
| 7 cmdlinepart partitions found on MTD device spi0.0 | 7 cmdlinepart partitions found on MTD device spi0.0 | ||
| - | '' | ||
| ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ||
| Line 89: | Line 75: | ||
| | mtd3 | 0x000000060000 | 0x000000070000 | 0x00010000 | 0x00010000 | art | | | mtd3 | 0x000000060000 | 0x000000070000 | 0x00010000 | 0x00010000 | art | | ||
| | mtd4 | 0x000000700000 | 0x0000001D0000 | 0x00160000 | 0x00010000 | kernel | | | mtd4 | 0x000000700000 | 0x0000001D0000 | 0x00160000 | 0x00010000 | kernel | | ||
| - | | mtd5 | 0x0000001D0000 | 0x000001000000 | 0x00e30000 | 0x00010000 | rootfs | + | | mtd5 | 0x0000001D0000 | 0x000001000000 | 0x00e30000 | 0x00010000 | rootfs | |
| | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | ||
| - | ====== photos ====== | ||
| - | {{: | ||
| - | ====== Hardware ====== | ||
| - | ===== Info ===== | + | ===== Hardware |
| + | |||
| + | ==== Info ==== | ||
| ^ [[wp> | ^ [[wp> | ||
| - | ^ [[docs: | + | ^ [[docs: |
| ^ [[docs: | ^ [[docs: | ||
| ^ [[docs: | ^ [[docs: | ||
| Line 107: | Line 92: | ||
| ^ Ethernet | ^ Ethernet | ||
| ^ Antenna | ^ Antenna | ||
| - | ^ PCIE | + | ^ PCIE | 1x miniPCIE | |
| ^ SIM | 1x microSIM slot| | ^ SIM | 1x microSIM slot| | ||
| - | ^ [[docs: | + | ^ [[docs: |
| ^ LED | Standard Ethernet LED's, WIFI LED | | ^ LED | Standard Ethernet LED's, WIFI LED | | ||
| ^ Hardware buttons | reset button | | ^ Hardware buttons | reset button | | ||
| - | ^ Power | 1x DC jack for main power input (9-12 V) | | + | ^ Power | 1x DC jack for main power input (9-48 V) | |
| ^ Board Size | 85 x 85x 16mm (L x W x H) | | ^ Board Size | 85 x 85x 16mm (L x W x H) | | ||
| - | ===== Specification ===== | ||
| * 650/391/216 MHz (CPU/ | * 650/391/216 MHz (CPU/ | ||
| * 64/128 MB of RAM (DDR2) | * 64/128 MB of RAM (DDR2) | ||
| * 8/16 MB of FLASH (SPI NOR) | * 8/16 MB of FLASH (SPI NOR) | ||
| - | * 2T2R 2.4 GHz (QCA9531) | ||
| * 2x 10/100 Mbps Ethernet (one port support POE) | * 2x 10/100 Mbps Ethernet (one port support POE) | ||
| * 6x LED (1x RGB, 5 driven by GPIO) | * 6x LED (1x RGB, 5 driven by GPIO) | ||
| - | * 1x button (reset) | ||
| - | * 1x miniPCIE slot | ||
| * 1x microSIM slot | * 1x microSIM slot | ||
| - | * 1x DC jack for main power input (9-12 V) | ||
| * UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB | * UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB | ||
| - | ===== Board Photos | + | ==== Photos ==== |
| - | | + | {{: |
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | ==== Serial | ||
| + | Serial connection settings: | ||
| - | 115200 8N1, no hardware flow control. | ||
| {{: | {{: | ||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||