Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:qxwlan:e600g [2018/06/27 06:35] – [Info] zhangsd20 | toh:qxwlan:e600g [2018/09/12 08:34] – Section heading levels corrected, some cleanup tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Qxwlan E600G ====== | + | ====== Qxwlan E600G V2====== |
| - | {{: | + | {{: |
| ===== Important notice ===== | ===== Important notice ===== | ||
| - | First version of these boards are using different mtd layout, with ART | + | <color #ed1c24>First version of these boards are using different mtd layout, with ART data at the end. You should not use v2 images on v1 board because it will result in lost of ART data!</ |
| - | data at the end. You should not use v2 images on v1 board because it | + | |
| - | will result in lost of ART data! | + | |
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| Line 30: | Line 28: | ||
| cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| - | align : | + | align : |
| filter | filter | ||
| ---- | ---- | ||
| + | |||
| + | Flash instruction (using U-Boot CLI and tftp server): | ||
| + | |||
| + | - Configure PC with static IP 192.168.1.10 and tftp server. | ||
| + | - Rename '' | ||
| + | - Connect PC with one of RJ45 ports, power up the board and press " | ||
| + | - Use the following command to update the device to OpenWrt: '' | ||
| + | |||
| + | Flash instruction (using U-Boot web-based recovery): | ||
| + | |||
| + | - Configure PC with static IP 192.168.1.xxx(2-254)/ | ||
| + | - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. | ||
| + | - Open your browser and enter 192.168.1.1, | ||
| ===== U-boot controller ===== | ===== U-boot controller ===== | ||
| Line 38: | Line 49: | ||
| U-Boot 1.1.4 (Jun 27 2018 - 11: | U-Boot 1.1.4 (Jun 27 2018 - 11: | ||
| - | E600G (QCA95xX) U-Boot | + | E600G (QCA953X) U-Boot |
| | | ||
| DRAM: 16bit ddr2 128 MB | DRAM: 16bit ddr2 128 MB | ||
| Line 51: | Line 62: | ||
| ath> | ath> | ||
| - | ===== Upgrading firmware ===== | ||
| - | |||
| - | Flash instruction (using U-Boot CLI and tftp server): | ||
| - | |||
| - | 1. Configure PC with static IP 192.168.1.10 and tftp server. | ||
| - | | ||
| - | 2. Rename " | ||
| - | tftp server directory. | ||
| - | | ||
| - | 3. Connect PC with one of RJ45 ports, power up the board and press " | ||
| - | key to access U-Boot CLI. | ||
| - | | ||
| - | 4. Use the following command to update the device to OpenWrt: "run lfw". | ||
| - | |||
| - | Flash instruction (using U-Boot web-based recovery): | ||
| - | |||
| - | 1. Configure PC with static IP 192.168.1.xxx(2-254)/ | ||
| - | | ||
| - | 2. Connect PC with one of RJ45 ports, press the reset button, | ||
| - | power up the board and keep button pressed for around 6-7 seconds, | ||
| - | until LEDs start flashing. | ||
| - | |||
| - | 3. Open your browser and enter 192.168.1.1, | ||
| - | and click the upgrade button. | ||
| ===== Default FLASH Layout ===== | ===== Default FLASH Layout ===== | ||
| - | ,, | + | |
| m25p80 spi0.0: found w25q128, expected m25p80 | m25p80 spi0.0: found w25q128, expected m25p80 | ||
| m25p80 spi0.0: w25q128 (16384 Kbytes) | m25p80 spi0.0: w25q128 (16384 Kbytes) | ||
| 7 cmdlinepart partitions found on MTD device spi0.0 | 7 cmdlinepart partitions found on MTD device spi0.0 | ||
| - | '' | ||
| ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ||
| Line 89: | Line 75: | ||
| | mtd3 | 0x000000060000 | 0x000000070000 | 0x00010000 | 0x00010000 | art | | | mtd3 | 0x000000060000 | 0x000000070000 | 0x00010000 | 0x00010000 | art | | ||
| | mtd4 | 0x000000700000 | 0x0000001D0000 | 0x00160000 | 0x00010000 | kernel | | | mtd4 | 0x000000700000 | 0x0000001D0000 | 0x00160000 | 0x00010000 | kernel | | ||
| - | | mtd5 | 0x0000001D0000 | 0x000001000000 | 0x00e30000 | 0x00010000 | rootfs | + | | mtd5 | 0x0000001D0000 | 0x000001000000 | 0x00e30000 | 0x00010000 | rootfs | |
| | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | ||
| - | ==== photos | + | |
| - | {{: | + | |
| + | ===== Hardware | ||
| ==== Info ==== | ==== Info ==== | ||
| ^ [[wp> | ^ [[wp> | ||
| - | ^ [[docs: | + | ^ [[docs: |
| ^ [[docs: | ^ [[docs: | ||
| ^ [[docs: | ^ [[docs: | ||
| Line 105: | Line 92: | ||
| ^ Ethernet | ^ Ethernet | ||
| ^ Antenna | ^ Antenna | ||
| - | ^ PCIE | + | ^ PCIE | 1x miniPCIE | |
| ^ SIM | 1x microSIM slot| | ^ SIM | 1x microSIM slot| | ||
| - | ^ [[docs: | + | ^ [[docs: |
| ^ LED | Standard Ethernet LED's, WIFI LED | | ^ LED | Standard Ethernet LED's, WIFI LED | | ||
| ^ Hardware buttons | reset button | | ^ Hardware buttons | reset button | | ||
| - | ^ Power | 1x DC jack for main power input (9-12 V) | | + | ^ Power | 1x DC jack for main power input (9-48 V) | |
| ^ Board Size | 85 x 85x 16mm (L x W x H) | | ^ Board Size | 85 x 85x 16mm (L x W x H) | | ||
| - | ==== Specification ==== | ||
| * 650/391/216 MHz (CPU/ | * 650/391/216 MHz (CPU/ | ||
| * 64/128 MB of RAM (DDR2) | * 64/128 MB of RAM (DDR2) | ||
| * 8/16 MB of FLASH (SPI NOR) | * 8/16 MB of FLASH (SPI NOR) | ||
| - | * 2T2R 2.4 GHz (QCA9531) | ||
| * 2x 10/100 Mbps Ethernet (one port support POE) | * 2x 10/100 Mbps Ethernet (one port support POE) | ||
| * 6x LED (1x RGB, 5 driven by GPIO) | * 6x LED (1x RGB, 5 driven by GPIO) | ||
| - | * 1x button (reset) | ||
| - | * 1x miniPCIE slot | ||
| * 1x microSIM slot | * 1x microSIM slot | ||
| - | * 1x DC jack for main power input (9-12 V) | ||
| * UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB | * UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB | ||
| - | ==== Board Photos | + | ==== Photos ==== |
| - | {{: | + | {{: |
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | ==== Serial ==== | ||
| + | Serial connection settings: 115200 8N1, no hardware flow control. | ||
| + | |||
| + | {{: | ||
| + | |||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||