Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:qxwlan:e600g [2018/06/22 10:46] – zhangsd20 | toh:qxwlan:e600g [2018/09/12 08:34] – Section heading levels corrected, some cleanup tmomas | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Qxwlan E600G ====== | + | ====== Qxwlan E600G V2====== |
| - | {{: | + | {{: |
| + | |||
| + | ===== Important notice ===== | ||
| + | |||
| + | <color # | ||
| ===== Supported Versions ===== | ===== Supported Versions ===== | ||
| Line 24: | Line 28: | ||
| cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| - | align : | + | align : |
| filter | filter | ||
| ---- | ---- | ||
| - | |||
| - | ===== Upgrading OpenWrt ===== | ||
| Flash instruction (using U-Boot CLI and tftp server): | Flash instruction (using U-Boot CLI and tftp server): | ||
| - | | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| Flash instruction (using U-Boot web-based recovery): | Flash instruction (using U-Boot web-based recovery): | ||
| - | | + | |
| - | | + | |
| - | | + | |
| + | |||
| + | ===== U-boot controller ===== | ||
| + | |||
| + | U-Boot 1.1.4 (Jun 27 2018 - 11: | ||
| + | |||
| + | E600G (QCA953X) U-Boot | ||
| + | |||
| + | DRAM: 16bit ddr2 128 MB | ||
| + | FLASH: | ||
| + | |||
| + | LED on during eth initialization... | ||
| + | |||
| + | eth0 up | ||
| + | eth0 | ||
| + | Setting 0x181162c0 to 0x68d02100 | ||
| + | Hit any key to stop autoboot: | ||
| + | ath> | ||
| + | |||
| + | |||
| + | ===== Default FLASH Layout ===== | ||
| + | |||
| + | m25p80 spi0.0: found w25q128, expected m25p80 | ||
| + | m25p80 spi0.0: w25q128 (16384 Kbytes) | ||
| + | 7 cmdlinepart partitions found on MTD device spi0.0 | ||
| + | |||
| + | ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | ||
| + | | mtd0 | 0x000000000000 | 0x000000040000 | 0x00040000 | 0x00010000 | u-boot | | ||
| + | | mtd1 | 0x000000040000 | 0x000000050000 | 0x00010000 | 0x00010000 | u-boot-env | | ||
| + | | mtd2 | 0x000000050000 | 0x000000060000 | 0x00010000 | 0x00010000 | pri-data | | ||
| + | | mtd3 | 0x000000060000 | 0x000000070000 | 0x00010000 | 0x00010000 | art | | ||
| + | | mtd4 | 0x000000700000 | 0x0000001D0000 | 0x00160000 | 0x00010000 | kernel | | ||
| + | | mtd5 | 0x0000001D0000 | 0x000001000000 | 0x00e30000 | 0x00010000 | rootfs | | ||
| + | | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | ||
| + | |||
| + | |||
| + | |||
| + | ===== Hardware ===== | ||
| + | |||
| + | ==== Info ==== | ||
| + | ^ [[wp> | ||
| + | ^ [[docs: | ||
| + | ^ [[docs: | ||
| + | ^ [[docs: | ||
| + | ^ Flash size | 16 MB NOR-Flash | | ||
| + | ^ RAM | 128 MB DDR2 RAM | | ||
| + | ^ Wireless | ||
| + | ^ Ethernet | ||
| + | ^ Antenna | ||
| + | ^ PCIE | 1x miniPCIE | | ||
| + | ^ SIM | 1x microSIM slot| | ||
| + | ^ [[docs: | ||
| + | ^ LED | Standard Ethernet LED's, WIFI LED | | ||
| + | ^ Hardware buttons | reset button | | ||
| + | ^ Power | 1x DC jack for main power input (9-48 V) | | ||
| + | ^ Board Size | 85 x 85x 16mm (L x W x H) | | ||
| - | ==== Specification ==== | ||
| * 650/391/216 MHz (CPU/ | * 650/391/216 MHz (CPU/ | ||
| * 64/128 MB of RAM (DDR2) | * 64/128 MB of RAM (DDR2) | ||
| * 8/16 MB of FLASH (SPI NOR) | * 8/16 MB of FLASH (SPI NOR) | ||
| - | | + | * 2x 10/100 Mbps Ethernet |
| - | * 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11) | + | |
| - | | + | |
| * 6x LED (1x RGB, 5 driven by GPIO) | * 6x LED (1x RGB, 5 driven by GPIO) | ||
| - | * 1x button (reset) | + | * 1x microSIM slot |
| - | * 1x DC jack for main power input (9-12 V) | + | |
| * UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB | * UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB | ||
| + | ==== Photos ==== | ||
| + | {{: | ||
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | ==== Serial ==== | ||
| + | Serial connection settings: 115200 8N1, no hardware flow control. | ||
| + | |||
| + | {{: | ||
| + | |||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||