Qxwlan E2600AC C1/C2

Flash instruction (using U-Boot web-based recovery):

  1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
  2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing.
  3. Open your browser and enter 192.168.1.1, if your board is e2600ac c1, select “sysupgrade” image and click the upgrade button.
  4. Open your browser and enter 192.168.1.1, if your board is e2600ac c2, select “ubi” image and click the upgrade button.

Firmware OpenWrt Install:

  1. E2600AC C1/C2, select “xxx-sysupgrade.bin”
U-Boot 2012.07 [local,local] (Dec 27 2018 - 16:15:16)
  Qxwlan E2600AC-C2 Support (nor-nand) 
smem ram ptable found: ver: 1 len: 3
DRAM:  256 MiB
machid : 0x8010206
NAND:  ID = 9580f12c
Vendor = 2c
Device = f1
ONFI device found
SF: Detected W25Q128 with page size 64 KiB, total 16 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x1000000
144 MiB
MMC:   qca_mmc: 0
In:    serial
Out:   serial
Err:   serial
machid: 8010206
flash_type: 0
Net:   MAC0 addr:dc:eb:53:11:bf:a0
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
Hit any key to stop autoboot:  0 
(IPQ40xx) #
1 fixed-partitions partitions found on MTD device qcom_nand.0
Creating 1 MTD partitions on "qcom_nand.0":
0x000000000000-0x000004000000 : "ubi"
m25p80 spi0.0: w25q128 (16384 Kbytes)
8 fixed-partitions partitions found on MTD device spi0.0

NAND Flash

Partition Start End Size Erasesize Name
mtd0 0x000000000000 0x000004000000 0x04000000 0x00010000 ubi

NOR Flash

Partition Start End Size Erasesize Name
mtd1 0x000000000000 0x000000040000 0x00040000 0x00010000 0:SBL1
mtd2 0x000000040000 0x000000060000 0x00020000 0x00010000 0:MIBIB
mtd3 0x000000060000 0x0000000c0000 0x00060000 0x00010000 0:QSEE
mtd4 0x0000000c0000 0x0000000d0000 0x00010000 0x00010000 0:CDT
mtd5 0x0000000d0000 0x0000000e0000 0x00010000 0x00010000 0:DDRPARAMS
mtd6 0x0000000e0000 0x0000000f0000 0x00010000 0x00010000 0:APPSBLENV
mtd7 0x0000000f0000 0x000000170000 0x00080000 0x00010000 0:APPSBL
mtd8 0x000000170000 0x000000180000 0x00010000 0x00010000 0:ART
Architecture ARM
bootloader web u-boot
System-On-Chip IPQ4019 + QCA8075
Flash size 16 M NOR-Flash + 128M Nand-Flash
RAM 256 MB DDR3 RAM
Wireless WiFi 11ac/g/n with IPQ4019
Ethernet 3x 10/100/1000 Base-T(X) (one port support POE)
Antenna 2T2R 2.4 GHz 2T2R 5L/H GHz MMCX*6
USB 1x 3.0 (host)
PCIE 1x miniPCIE
SIM 1x microSIM slot
SD 1x sd card slot
Serial YES ( RS232 (soldering needed))
LED Standard Ethernet LED's, WIFI LED
Hardware buttons reset button
Power 1x DC jack for main power input (9-48 V)
Board Size 155 x 118 x 17mm (L x W x H)
  • 256 MB of RAM (DDR3)
  • 16 MB of FLASH (SPI NOR)
  • 128 MB of FLASH (NAND)
  • 2T2R 2.4 GHz
  • 2T2R 5L/H GHz
  • 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
  • 1x miniPCIe slot
  • 11x LED (10 driven by GPIO)
  • 1x 2-pos switch

Serial connection settings: 115200 8N1, no hardware flow control.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1