Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:qxwlan:e1700ac [2018/06/27 05:45] – [Default FLASH Layout] zhangsd20 | toh:qxwlan:e1700ac [2019/08/05 08:33] – [Qxwlan E1700AC V2] zhangsd20 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Qxwlan E1700AC V2 ====== | ====== Qxwlan E1700AC V2 ====== | ||
| - | {{: | + | {{: |
| - | ====== Important | + | ===== Important |
| <color # | <color # | ||
| Line 34: | Line 33: | ||
| filter | filter | ||
| ---- | ---- | ||
| - | |||
| - | ===== Upgrading Firmware ===== | ||
| Flash instruction (using U-Boot CLI and tftp server): | Flash instruction (using U-Boot CLI and tftp server): | ||
| - | | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| Flash instruction (using U-Boot web-based recovery): | Flash instruction (using U-Boot web-based recovery): | ||
| - | | + | |
| - | | + | |
| - | | + | |
| + | |||
| + | ===== U-boot controller ===== | ||
| + | |||
| + | U-Boot 1.1.4 (Jun 27 2018 - 11: | ||
| + | |||
| + | E1700AC (QCA956X) U-Boot | ||
| + | |||
| + | DRAM: 16bit ddr2 128 MB | ||
| + | FLASH: | ||
| + | |||
| + | LED on during eth initialization... | ||
| + | |||
| + | eth0 up | ||
| + | eth0 | ||
| + | Setting 0x181162c0 to 0xb2d02100 | ||
| + | Hit any key to stop autoboot: | ||
| + | ath> | ||
| ===== Default FLASH Layout ===== | ===== Default FLASH Layout ===== | ||
| - | ,, | + | |
| m25p80 spi0.0: found w25q128, expected m25p80 | m25p80 spi0.0: found w25q128, expected m25p80 | ||
| m25p80 spi0.0: w25q128 (16384 Kbytes) | m25p80 spi0.0: w25q128 (16384 Kbytes) | ||
| 7 cmdlinepart partitions found on MTD device spi0.0 | 7 cmdlinepart partitions found on MTD device spi0.0 | ||
| - | '' | ||
| - | ^ Partition ^ Start ^ End ^ Size ^ Erasesize ^ Name ^ | + | ^ Partition |
| - | | mtd0 | 0x000000000000 | 0x000000040000 | 0x00040000 | 0x00010000 | u-boot | + | | mtd0 | 0x000000000000 |
| - | | mtd1 | 0x000000040000 | 0x000000050000 | 0x00010000 | 0x00010000 | u-boot-env | + | | mtd1 | 0x000000040000 |
| - | | mtd2 | 0x000000050000 | 0x000000060000 | 0x00010000 | 0x00010000 | pri-data | + | | mtd2 | 0x000000050000 |
| - | | mtd3 | 0x000000060000 | 0x000000070000 | 0x00010000 | 0x00010000 | art | | | + | | mtd3 | 0x000000060000 |
| - | | mtd4 | 0x000000700000 | 0x0000001D0000 | 0x00160000 | 0x00010000 | kernel | + | | mtd4 | 0x000000700000 |
| - | | mtd5 | 0x0000001D0000 | 0x000001000000 | 0x00e30000 | 0x00010000 | rootfs | + | | mtd5 | 0x0000001D0000 |
| - | | mtd6 | 0x000000070000 | 0x000001000000 | 0x00F90000 | 0x00010000 | firmware | | | + | | mtd6 | 0x000000070000 |
| - | ===== Photos ===== | ||
| - | {{: | ||
| - | {{: | ||
| - | {{: | ||
| ===== Hardware ===== | ===== Hardware ===== | ||
| + | |||
| ==== Info ==== | ==== Info ==== | ||
| ^ [[wp> | ^ [[wp> | ||
| Line 79: | Line 90: | ||
| ^ Flash size | 16 MB NOR-Flash | | ^ Flash size | 16 MB NOR-Flash | | ||
| ^ RAM | 128 MB DDR2 RAM | | ^ RAM | 128 MB DDR2 RAM | | ||
| - | ^ Wireless | + | ^ Wireless |
| - | ^ Ethernet | + | ^ Ethernet |
| - | ^ Antenna | + | ^ Antenna |
| ^ USB | 1x 2.0 (host), 1x miniUSB (slave) | | ^ USB | 1x 2.0 (host), 1x miniUSB (slave) | | ||
| + | ^ PCIE | 1x miniPCIE | | ||
| ^ SIM | 1x microSIM slot| | ^ SIM | 1x microSIM slot| | ||
| ^ [[docs: | ^ [[docs: | ||
| ^ LED | Standard Ethernet LED's, WIFI LED | | ^ LED | Standard Ethernet LED's, WIFI LED | | ||
| ^ Hardware buttons | reset button | | ^ Hardware buttons | reset button | | ||
| + | ^ Power | 1x DC jack for main power input (9-48 V) | | ||
| + | ^ Board Size | 140 x 102 x 10mm (L x W x H) | | ||
| Line 98: | Line 112: | ||
| * 2x 10/100/1000 Mbps Ethernet (one port with PoE support) | * 2x 10/100/1000 Mbps Ethernet (one port with PoE support) | ||
| * 1x miniPCIe slot (USB 2.0 bus only) | * 1x miniPCIe slot (USB 2.0 bus only) | ||
| - | * 1x microSIM slot | ||
| - | * 1x USB 2.0 | ||
| * 5x LED (4 driven by GPIO) | * 5x LED (4 driven by GPIO) | ||
| - | * 1x button (reset) | ||
| * 1x 2-pos switch | * 1x 2-pos switch | ||
| - | * 1x DC jack for main power input (9-48 V) | ||
| * UART (J5) and LEDs (J13) headers on PCB | * UART (J5) and LEDs (J13) headers on PCB | ||
| + | ==== Photos ==== | ||
| + | {{: | ||
| + | {{: | ||
| + | {{: | ||
| + | ==== Serial ==== | ||
| + | Serial connection settings: 115200 8N1, no hardware flow control. | ||
| - | + | {{: | |
| - | ==== Board Photos Info ==== | + | |
| - | + | ||
| - | Serial connection settings: | + | |
| - | * 115200 8N1, no hardware flow control. | + | |
| - | + | ||
| - | {{: | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||