Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
| toh:qxwlan:e1700ac [2018/06/22 02:41] – removed zhangsd20 | toh:qxwlan:e1700ac [2024/02/12 08:58] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Qxwlan E1700AC V2 ====== | ||
| + | {{: | ||
| + | ===== Important Notice ===== | ||
| + | |||
| + | <color # | ||
| + | data at the end. You should not use v2 images on v1 board because it | ||
| + | will result in lost of ART data!</ | ||
| + | |||
| + | ===== Supported Versions ===== | ||
| + | <!-- ToH: { | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | } --> | ||
| + | |||
| + | |||
| + | ===== Hardware Highlights ===== | ||
| + | <!-- ToH: { | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | } --> | ||
| + | |||
| + | |||
| + | ===== Installation ===== | ||
| + | <!-- ToH: { | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | } --> | ||
| + | |||
| + | Flash instruction (using U-Boot CLI and tftp server): | ||
| + | |||
| + | - Configure PC with static IP 192.168.1.10 and tftp server. | ||
| + | - Rename '' | ||
| + | - Connect PC with one of RJ45 ports, power up the board and press " | ||
| + | - Use the following command to update the device to OpenWrt: "run lfw". | ||
| + | |||
| + | Flash instruction (using U-Boot web-based recovery): | ||
| + | |||
| + | - Configure PC with static IP 192.168.1.xxx(2-254). | ||
| + | - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. | ||
| + | - Open your browser and enter 192.168.1.1, | ||
| + | |||
| + | ===== U-boot controller ===== | ||
| + | |||
| + | U-Boot 1.1.4 (Jun 27 2018 - 11: | ||
| + | |||
| + | E1700AC (QCA956X) U-Boot | ||
| + | | ||
| + | DRAM: 16bit ddr2 128 MB | ||
| + | FLASH: | ||
| + | | ||
| + | LED on during eth initialization... | ||
| + | | ||
| + | eth0 up | ||
| + | eth0 | ||
| + | Setting 0x181162c0 to 0xb2d02100 | ||
| + | Hit any key to stop autoboot: | ||
| + | ath> | ||
| + | |||
| + | |||
| + | ===== Default FLASH Layout ===== | ||
| + | |||
| + | m25p80 spi0.0: found w25q128, expected m25p80 | ||
| + | m25p80 spi0.0: w25q128 (16384 Kbytes) | ||
| + | 7 cmdlinepart partitions found on MTD device spi0.0 | ||
| + | |||
| + | ^ Partition | ||
| + | | mtd0 | 0x000000000000 | ||
| + | | mtd1 | 0x000000040000 | ||
| + | | mtd2 | 0x000000050000 | ||
| + | | mtd3 | 0x000000060000 | ||
| + | | mtd4 | 0x000000700000 | ||
| + | | mtd5 | 0x0000001D0000 | ||
| + | | mtd6 | 0x000000070000 | ||
| + | |||
| + | |||
| + | ===== Hardware ===== | ||
| + | |||
| + | ==== Info ==== | ||
| + | ^ [[wp> | ||
| + | ^ [[docs: | ||
| + | ^ [[docs: | ||
| + | ^ [[docs: | ||
| + | ^ Flash size | 16 MB NOR-Flash | | ||
| + | ^ RAM | 128 MB DDR2 RAM | | ||
| + | ^ Wireless | ||
| + | ^ Ethernet | ||
| + | ^ Antenna | ||
| + | ^ USB | 1x 2.0 (host), 1x miniUSB (slave) | | ||
| + | ^ PCIE | 1x miniPCIE | | ||
| + | ^ SIM | 1x microSIM slot| | ||
| + | ^ [[docs: | ||
| + | ^ LED | Standard Ethernet LED's, WIFI LED | | ||
| + | ^ Hardware buttons | reset button | | ||
| + | ^ Power | 1x DC jack for main power input (9-48 V) | | ||
| + | ^ Board Size | 140 x 102 x 10mm (L x W x H) | | ||
| + | |||
| + | |||
| + | ==== Specification ===== | ||
| + | |||
| + | * 750/400/250 MHz (CPU/ | ||
| + | * 128 MB of RAM (DDR2) | ||
| + | * 8/16 MB of FLASH (SPI NOR) | ||
| + | * 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11) | ||
| + | * 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11) | ||
| + | * 2x 10/100/1000 Mbps Ethernet (one port with PoE support) | ||
| + | * 1x miniPCIe slot (USB 2.0 bus only) | ||
| + | * 5x LED (4 driven by GPIO) | ||
| + | * 1x 2-pos switch | ||
| + | * UART (J5) and LEDs (J13) headers on PCB | ||
| + | |||
| + | ==== Photos ==== | ||
| + | {{: | ||
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | ==== Serial ==== | ||
| + | |||
| + | Serial connection settings: 115200 8N1, no hardware flow control. | ||
| + | |||
| + | {{: | ||
| + | |||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||