QNAP QHora-301w
Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.
Supported Versions
Hardware Highlights
CPU | Ram | Flash | Network | WLAN2.4 | WLAN5.0 | USB | Serial |
---|---|---|---|---|---|---|---|
Qualcomm IPQ8072A @ 2.2 GHz | 1024 MiB | 4GB eMMC/ 8MB NOR | 4x 10/100/1000 2x 1000/2500/5000/10000 | b/g/n/ax | a/n/ac/ax | 2x 3.2 Gen 1 | Yes |
Installation
→ Device specific installation instructions in the commit message
Decide whether that will stay the recommended installation procedure, and copy over here.
Hardware
Info
Architecture | ARMv8 |
---|---|
Vendor | Qualcomm |
Bootloader | U-Boot |
System-On-Chip | Qualcomm IPQ8072A |
CPU/Speed | 2.2 GHz |
Flash-Chip | Winbond W25Q64DW |
Flash size | 8 MiB |
eMMC | 4096 MiB MTFC4GACAJCN-1M |
RAM | 1024 MiB |
Wireless 2.4GHz | QCN5024 + SKY85347 802.11b/g/n/ax |
Wireless 5GHz | QCN5054 + SKY85755 802.11a/g/n/ac/ax |
Ethernet | 4x 10/100/1000 Mbit/s (QCA8075) 2x 1000/2500/5000/10000 Mbit/s (Aquantia AQR113c) |
Switch | integrated in the SoC |
USB | 2x 3.0 |
Serial | Yes |
Flash Layout SPI NOR
dev: size erasesize name mtd0: 00050000 00010000 "0:SBL1" mtd1: 00010000 00010000 "0:MIBIB" mtd2: 00180000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:DEVCFG" mtd4: 00010000 00010000 "0:APDP" mtd5: 00040000 00010000 "0:RPM" mtd6: 00010000 00010000 "0:CDT" mtd7: 00020000 00010000 "0:APPSBLENV" mtd8: 00100000 00010000 "0:APPSBL" mtd9: 00040000 00010000 "0:ART" mtd10: 00080000 00010000 "0:ETHPHYFW" mtd11: 003d0000 00010000 "reserved"
Flash Layout eMMC
Command (m for help): p Disk /dev/mmcblk0: 3.7 GiB, 3909091328 bytes, 7634944 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: gpt Disk identifier: 98101B32-BBE2-4BF2-A06E-2BB33D000C20 Device Start End Sectors Size Type /dev/mmcblk0p1 34 32801 32768 16M unknown /dev/mmcblk0p2 32802 65569 32768 16M unknown /dev/mmcblk0p3 65570 98337 32768 16M unknown /dev/mmcblk0p4 98338 1146913 1048576 512M unknown /dev/mmcblk0p5 1146914 2195489 1048576 512M unknown /dev/mmcblk0p6 2195490 3244065 1048576 512M unknown /dev/mmcblk0p7 3244066 3252257 8192 4M unknown /dev/mmcblk0p8 3252258 3285025 32768 16M Linux reserved /dev/mmcblk0p9 3285026 7591969 4306944 2.1G unknown
Photos
Opening the case
Device has 6 screws, 4 behind the rubber feet, 1 in the middle and one is hidden behind the device label (the smaller one on the right side)
Serial
Use the 3 pins in the middle, the 2 outer pins are VCC, do not connect them.
Middle pin is GND (blue wire), left pin is TX (purple wire), right pin is RX (green wire)
Serial connection parameters for QNAP 301w | 115200, 8N1, 3.3 V |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootlogs
OEM bootlog
Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158 S - IMAGE_VARIANT_STRING=HAABANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x000002e1 B - 201 - PBL, Start B - 2737 - bootable_media_detect_entry, Start B - 2883 - bootable_media_detect_success, Start B - 2888 - elf_loader_entry, Start B - 11378 - auth_hash_seg_entry, Start B - 11621 - auth_hash_seg_exit, Start B - 250658 - elf_segs_hash_verify_entry, Start B - 311327 - PBL, End B - 322903 - SBL1, Start B - 374814 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4 B - 381250 - pm_device_init, Start B - 502365 - PM_SET_VAL:Skip D - 120658 - pm_device_init, Delta B - 504775 - pm_driver_init, Start D - 5337 - pm_driver_init, Delta B - 511149 - clock_init, Start D - 2104 - clock_init, Delta B - 515175 - boot_flash_init, Start D - 15677 - boot_flash_init, Delta B - 534512 - boot_config_data_table_init, Start D - 1006 - boot_config_data_table_init, Delta - (575 Bytes) B - 542168 - Boot Setting : 0x00000618 B - 545889 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0 B - 552812 - sbl1_ddr_set_params, Start B - 556625 - CPR configuration: 0x30c B - 560071 - cpr_init, Start B - 562847 - Rail:0 Mode: 5 Voltage: 824000 B - 568062 - CL CPR settled at 776000mV B - 570899 - Rail:1 Mode: 5 Voltage: 880000 B - 575077 - Rail:1 Mode: 7 Voltage: 928000 D - 16531 - cpr_init, Delta B - 581970 - Pre_DDR_clock_init, Start B - 585966 - Pre_DDR_clock_init, End B - 589290 - DDR Type : PCDDR3 B - 595024 - do ddr sanity test, Start D - 1067 - do ddr sanity test, Delta B - 599874 - DDR: Start of HAL DDR Boot Training B - 604510 - DDR: End of HAL DDR Boot Training B - 610183 - DDR: Checksum to be stored on flash is 2070595187 B - 620583 - Image Load, Start D - 335958 - QSEE Image Loaded, Delta - (1376448 Bytes) B - 956632 - Image Load, Start D - 30 - SEC Image Loaded, Delta - (0 Bytes) B - 964288 - Image Load, Start D - 9760 - DEVCFG Image Loaded, Delta - (26008 Bytes) B - 974139 - Image Load, Start D - 25986 - RPM Image Loaded, Delta - (86584 Bytes) B - 1000217 - Image Load, Start D - 136579 - APPSBL Image Loaded, Delta - (556008 Bytes) B - 1136918 - QSEE Execution, Start D - 61 - QSEE Execution, Delta B - 1142713 - USB D+ check, Start D - 0 - USB D+ check, Delta B - 1149118 - SBL1, End D - 828502 - SBL1, Delta S - Flash Throughput, 4430 KB/s (2045623 Bytes, 461732 us) S - DDR Frequency, 466 MHz S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Aug 18 2020 - 16:35:27 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, no defaults defined
Nand Flash error. Status = 80
Reset cmd status failed
SPI_ADDR_LEN=3
SF: Detected W25Q64DW with page size 256 Bytes, erase size 4 KiB, total 8 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x800000
8 MiB
MMC: <NULL>: 0
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010000
Hit any key to stop autoboot: 2 1 0
MMC read: dev # 0, block # 34, count 32768 ... 32768 blocks read: OK
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk01' configuration
Trying 'kernel@1' kernel subimage
Description: ARM64 OpenWrt Linux-4.4.60
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 5080168 Bytes = 4.8 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41080000
Entry Point: 0x41080000
Hash algo: crc32
Hash value: 601db371
Hash algo: sha1
Hash value: 67168a753639fd8d3f357b58320dbf11e7604e87
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk01' configuration
Trying 'fdt@hk01' fdt subimage
Description: ARM64 OpenWrt qcom-ipq807x-hk01 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x444d8698
Data Size: 91662 Bytes = 89.5 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 909da436
Hash algo: sha1
Hash value: c518be5f9b045495141d5217890e256f4433cec1
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x444d8698
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3e6000, end 4a3ff60d ... OK
Using machid 0x8010000 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.60 (root@Hank) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 0784228+r49254) ) #5 SMP PREEMPT Thu Apr 29 17:21:32 CST 2021 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Ignoring memory range 0x40000000 - 0x41000000 [ 0.000000] Machine: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: OVERLAP DETECTED! [ 0.000000] wifi_dump@51100000 (0x0000000051100000--0x0000000051700000) overlaps with wigig_dump@51300000 (0x0000000051300000--0x0000000051700000) [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 15 pages/cpu @ffffffc03ef3f000 s21248 r8192 d32000 u61440 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 225036 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 root=PARTUUID=2a213133-47f8-80a1-5d66-1d565a2ec756 rootwait swiotlb=1 coherent_pool=2M [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] software IO TLB [mem 0x7fd3a000-0x7fd7a000] (0MB) mapped at [ffffffc03ed3a000-ffffffc03ed79fff] [ 0.000000] Memory: 883932K/914432K available (5716K kernel code, 643K rwdata, 2412K rodata, 2024K init, 488K bss, 30500K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc0040000 - 0xffffffbdc1000000 ( 15 MB actual) [ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03f000000 ( 1008 MB) [ 0.000000] .init : 0xffffffc000872000 - 0xffffffc000a6c000 ( 2024 KB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000872000 ( 8136 KB) [ 0.000000] .data : 0xffffffc000a7c000 - 0xffffffc000b1ce00 ( 644 KB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000485] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000498] pid_max: default: 32768 minimum: 301 [ 0.000598] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000608] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.001165] Initializing cgroup subsys io [ 0.001182] Initializing cgroup subsys memory [ 0.001208] Initializing cgroup subsys devices [ 0.001219] Initializing cgroup subsys freezer [ 0.001230] Initializing cgroup subsys net_cls [ 0.001239] Initializing cgroup subsys pids [ 0.001483] EFI services will not be available. [ 0.001508] ASID allocator initialised with 65536 entries [ 0.052142] MSM Memory Dump base table set up [ 0.052164] MSM Memory Dump apps data table set up [ 0.090054] Detected VIPT I-cache on CPU1 [ 0.090101] CPU1: Booted secondary processor [410fd034] [ 0.120041] Detected VIPT I-cache on CPU2 [ 0.120070] CPU2: Booted secondary processor [410fd034] [ 0.150070] Detected VIPT I-cache on CPU3 [ 0.150098] CPU3: Booted secondary processor [410fd034] [ 0.150150] Brought up 4 CPUs [ 0.150177] SMP: Total of 4 processors activated. [ 0.150187] CPU: All CPU(s) started at EL1 [ 0.150210] alternatives: patching kernel code [ 0.150703] devtmpfs: initialized [ 0.171287] DMI not present or invalid. [ 0.171530] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.171554] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.171905] pinctrl core: initialized pinctrl subsystem [ 0.172838] NET: Registered protocol family 16 [ 0.200018] cpuidle: using governor ladder [ 0.230036] cpuidle: using governor menu [ 0.230252] NET: Registered protocol family 42 [ 0.230339] vdso: 2 pages (1 code @ ffffffc000a81000, 1 data @ ffffffc000a80000) [ 0.230368] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.231018] DMA: preallocated 2048 KiB pool for atomic allocations [ 0.231156] CPU: IPQ8072A, SoC Version: 2.0 [ 0.231602] IPC logging disabled [ 0.231608] IPC logging disabled [ 0.231612] IPC logging disabled [ 0.231617] IPC logging disabled [ 0.231622] IPC logging disabled [ 0.233823] Soc version is not 1, changing clock offsets [ 0.242871] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.245668] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.249106] sps:sps is ready. [ 0.256004] spmi spmi-0: PMIC Arb Version-2 (0x20010000) [ 0.262719] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 0.263016] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2 [ 0.301945] pps_core: LinuxPPS API ver. 1 registered [ 0.301954] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 0.301977] PTP clock support registered [ 0.302134] dmi: Firmware registration failed. [ 0.303584] Advanced Linux Sound Architecture Driver Initialized. [ 0.304243] clocksource: Switched to clocksource arch_sys_counter [ 0.307804] NET: Registered protocol family 2 [ 0.308549] default registered [ 0.308557] default registered [ 0.308562] MPTCP: Stable release v0.92.2 [ 0.308604] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.308712] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 0.308897] TCP: Hash tables configured (established 8192 bind 8192) [ 0.308953] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.308990] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.309177] NET: Registered protocol family 1 [ 0.319677] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 0.330602] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.330620] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.334405] Key type asymmetric registered [ 0.334423] Asymmetric key parser 'x509' registered [ 0.334455] io scheduler noop registered [ 0.334469] io scheduler deadline registered (default) [ 0.336115] hora_gpio: Register a char device 246:0 [ 0.337460] 20000000.pci supply vdda not found, using dummy regulator [ 0.337534] 20000000.pci supply vdda_phy not found, using dummy regulator [ 0.337571] 20000000.pci supply vdda_refclk not found, using dummy regulator [ 0.338256] PCI host bridge /soc/pci@20000000 ranges: [ 0.338283] IO 0x20200000..0x2020ffff → 0x20200000 [ 0.338298] MEM 0x20220000..0x2fffffff → 0x20220000 [ 1.485907] qcom-pcie 20000000.pci: phy link never came up [ 1.487465] qcom-pcie 20000000.pci: hostinit failed [ 1.487475] qcom-pcie 20000000.pci: cannot initialize host [ 1.487623] qcom-pcie: probe of 20000000.pci failed with error -110 [ 1.487807] 10000000.pci supply vdda not found, using dummy regulator [ 1.487849] 10000000.pci supply vdda_phy not found, using dummy regulator [ 1.487882] 10000000.pci supply vdda_refclk not found, using dummy regulator [ 1.488467] PCI host bridge /soc/pci@10000000 ranges: [ 1.488490] IO 0x10200000..0x1020ffff → 0x10200000 [ 1.488504] MEM 0x10220000..0x1fffffff → 0x10220000 [ 2.634295] qcom-pcie 10000000.pci: phy link never came up [ 2.635852] qcom-pcie 10000000.pci: hostinit failed [ 2.635861] qcom-pcie 10000000.pci: cannot initialize host [ 2.635978] qcom-pcie: probe of 10000000.pci failed with error -110 [ 2.636368] MDSS QPIC HW Base phy_Address=0x7980000 virt=ffffff80005c0000 [ 2.636750] mdss_qpic_panel_probe: Panel Name = qpic lcd panel [ 2.638062] mdss_fb_register: FrameBuffer[0] 800×480 registered successfully! [ 2.642014] msm_rpm_log_probe: OK [ 2.642351] msm-dcc b3000.dcc: DCC XPU is not specified [ 2.642655] msm-dcc b3000.dcc: jiffies_64: 0xffff8bd7, cntvct_64: 0x9e41fe4 [ 2.642668] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff80005bc004) [ 2.642678] msm-dcc b3000.dcc: gcnt_lo: 0x09e421bd(0xffffff80005bc000) [ 2.643255] TZ SMMU State: SMMU Stage2 Enabled [ 2.643311] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set [ 2.644983] msm_serial 78b3000.serial: msm_serial: detected port #0 [ 2.645027] msm_serial 78b3000.serial: uartclk = 3686400 [ 2.645069] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) is a MSM [ 2.645090] msm_serial: console setup on port #0 [ 3.513476] console [ttyMSM0] enabled [ 3.518529] msm_serial: driver initialized [ 3.522003] msm_serial_hsl_init: driver initialized [ 3.535425] brd: module loaded [ 3.540114] loop: module loaded [ 3.540725] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 3.543539] m25p80 spi32766.0: found w25q64dw, expected n25q128a11 [ 3.549387] m25p80 spi32766.0: w25q64dw (8192 Kbytes) [ 3.555407] 12 ofpart partitions found on MTD device spi32766.0 [ 3.560460] Creating 12 MTD partitions on “spi32766.0”: [ 3.566214] 0x000000000000-0x000000050000 : “0:SBL1” [ 3.572181] 0x000000050000-0x000000060000 : “0:MIBIB” [ 3.577343] 0x000000060000-0x0000001e0000 : “0:QSEE” [ 3.582238] 0x0000001e0000-0x0000001f0000 : “0:DEVCFG” [ 3.587328] 0x0000001f0000-0x000000200000 : “0:APDP” [ 3.592234] 0x000000200000-0x000000240000 : “0:RPM” [ 3.597398] 0x000000240000-0x000000250000 : “0:CDT” [ 3.601969] 0x000000250000-0x000000270000 : “0:APPSBLENV” [ 3.606873] 0x000000270000-0x000000370000 : “0:APPSBL” [ 3.612396] 0x000000370000-0x0000003b0000 : “0:ART” [ 3.617473] 0x0000003b0000-0x000000430000 : “0:ETHPHYFW” [ 3.622182] 0x000000430000-0x000000800000 : “reserved” [ 3.628797] libphy: Fixed MDIO Bus: probed [ 4.292783] libphy: qca_mdio: probed [ 4.300999] qca-mdio 90000.mdio: qca-mdio driver was registered [ 4.301311] Unable to create IPC log context! [ 4.306047] Skip QCA8074V1 in V2 platform [ 4.310480] cnss: Platform driver probed successfully. plat ffffffc03cdf6018 tgt 0xfffe [ 4.314495] i2c /dev entries driver [ 4.329363] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 4.329853] sdhci: Secure Digital Host Controller Interface driver [ 4.336887] sdhci: Copyright© Pierre Ossman [ 4.342852] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.347872] qcom_ice_get_pdevice: invalid device list [ 4.353009] sdhci_msm 7824900.sdhci: sdhci_msm_ice_get_dev: ICE device not probed yet [ 4.357984] sdhci_msm 7824900.sdhci: sdhci_msm_probe: required ICE device not probed yet err = -517 [ 4.368669] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed [ 4.374716] ICE IRQ = 80 [ 4.383548] [ 4.383548] Version Rollback Feature Disabled [ 4.396271] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000008b04000 [ 4.396301] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04000 [ 4.412481] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04000 [ 4.428347] sps:BAM 0x0000000008b04000 is registered.[ 4.438261] remoteproc remoteproc0: releasing cd00000.qcom_q6v5_wcss [ 4.441560] SPMI VADC - Min ch: 0 Max ch: 15 [ 4.448923] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000 [ 4.451337] coresight-csr 6001000.csr: CSR initialized [ 4.458809] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000 [ 4.463756] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000 [ 4.471294] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000 [ 4.478676] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000 [ 4.486050] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000 [ 4.493413] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000 [ 4.500805] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000 [ 4.508187] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000 [ 4.515562] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000 [ 4.522928] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000 [ 4.530323] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000 [ 4.537694] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000 [ 4.545080] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000 [ 4.552440] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000 [ 4.559845] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000 [ 4.567215] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000 [ 4.574591] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000 [ 4.582156] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000 [ 4.589497] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000 [ 4.596922] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000 [ 4.604346] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000 [ 4.611679] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000 [ 4.618718] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000 [ 4.635810] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000 [ 4.651696] sps:BAM 0x0000000006044000 is registered.[ 4.659461] coresight-tmc 6028000.tmc: TMC initialized [ 4.664189] coresight-tmc 6027000.tmc: TMC initialized [ 4.669309] coresight-funnel 6021000.funnel: FUNNEL initialized [ 4.674326] coresight-funnel 6100000.funnel: FUNNEL initialized [ 4.680134] coresight-funnel 6120000.funnel: FUNNEL initialized [ 4.686044] coresight-funnel 6130000.funnel: FUNNEL initialized [ 4.691951] coresight-funnel 61a1000.funnel: FUNNEL initialized [ 4.698470] coresight-etm4x 619c000.etm: ETM 4.0 initialized [ 4.704099] coresight-etm4x 619d000.etm: ETM 4.0 initialized [ 4.710071] coresight-etm4x 619e000.etm: ETM 4.0 initialized [ 4.715744] coresight-etm4x 619f000.etm: ETM 4.0 initialized [ 4.720960] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized [ 4.726764] coresight-stm 6002000.stm: STM initialized [ 4.735325] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000 [ 4.739119] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized [ 4.749771] Netfilter messages via NETLINK v0.30. [ 4.754371] nf_conntrack version 0.5.0 (6905 buckets, 27620 max) [ 4.759329] ip_set: protocol 6 [ 4.765161] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.768637] NET: Registered protocol family 10 [ 4.784110] fullmesh registered [ 4.784136] NET: Registered protocol family 17 [ 4.786112] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 4.790604] Bridge firewalling registered [ 4.803364] 8021q: 802.1Q VLAN Support v1.8 [ 4.808881] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 4.811373] pmd9655_s3: supplied by e-smps1-reg [ 4.818704] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 [ 4.823031] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1 [ 4.829661] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 [ 4.837317] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable [ 4.844822] cpr3_mem_acc_init: apc: not using memory accelerator regulator [ 4.853937] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV [ 4.860898] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 840000 uV [ 4.870879] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 912000 uV [ 4.880685] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop=1000000 uV [ 4.890558] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 674, quot_offset[ 7]= 0 [ 4.900311] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 921, quot_offset[ 7]= 245 [ 4.911160] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1036, quot_offset[ 7]= 115 [ 4.922096] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1185, quot_offset[ 7]= 145 [ 4.933165] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop [ 4.944524] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2 [ 4.950830] pmd9655_s4: supplied by e-smps1-reg [ 4.957986] cpr3_mem_acc_init: npu: not using memory accelerator regulator [ 4.962269] npu_corner: fused NOM: open-loop= 808000 uV [ 4.969223] npu_corner: fused TURBO: open-loop= 872000 uV [ 4.975077] npu_corner: fused NOM: open-loop= 808000 uV [ 4.980668] npu_corner: fused TURBO: open-loop= 872000 uV [ 4.986342] npu_corner: Normal and Cold condition init done. Default to normal. [ 4.993132] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz [ 4.999166] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz [ 5.006893] qcom_ice_get_pdevice: found ice device ffffffc03c50a400 [ 5.014981] qcom_ice_get_pdevice: matching platform device ffffffc03d6b4400 [ 5.021060] sdhci_msm 7824900.sdhci: No vreg data found for vdd [ 5.027990] sdhci_msm 7824900.sdhci: No vreg data found for vdd-io [ 5.034056] qcom_ice 7803000.sdcc1ice: QC ICE 2.1.44 device found @0xffffff8000f6c000 [ 5.041200] sdhci_msm 7824900.sdhci: No vmmc regulator found [ 5.048050] sdhci_msm 7824900.sdhci: No vqmmc regulator found [ 5.094241] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit [ 5.100290] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss [ 5.101071] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available [ 5.111812] hctosys: unable to open rtc device (rtc0) [ 5.121141] pmd9655_ldo11: disabling [ 5.121772] ALSA device list: [ 5.125025] No soundcards found. [ 5.127906] Warning: unable to open an initial console. [ 5.131762] Freeing unused kernel memory: 2024K (ffffffc000872000 - ffffffc000a6c000) [ 5.136309] Freeing alternatives memory: 44K (ffffffc000a6c000 - ffffffc000a77000) + exec + mkdir -p /sys /proc + echo_dbg Making /sys... + echo -e \033[01;32mMaking /sys...\033[00m e[01;32mMaking /sys...e[00m + mount -t sysfs -o nodev,noexec,nosuid none /sys + echo_db[ 5.167878] mmc0: MAN_BKOPS_EN bit is not set g Making /proc... + echo -e \033[01;32mMaking /proc...\033[00m e[01;32mMaking /proc...e[00m + mount -t proc -o nodev,noexec,nosuid none /proc + wait_detect_emmc + local devname=/dev/mmcblk0p + local emmc_all_partition_exist=1 + seq 6 + emmc_all_par[ 5.193138] mmc0: new HS200 MMC card at address 0001 [ 5.195591] mmcblk0: mmc0:0001 Q2J54A 3.64 GiB [ 5.200586] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB [ 5.206205] GPT: device [179:4] (rootfs) set to be root filesystem [ 5.210668] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 tition_exist=1 + [ ! -e /dev/mmcblk0p1 ] + emmc_all_partition_exist=0 + break + [ 0 -eq 0 ] + sleep 1 + echo_dbg sleep 1 wait for emmc device /dev/mmcblk0p1 + echo -e \033[01;32msleep 1 wait for emmc device /dev/mmcblk0p1\033[00m e[01;32msleep 1 wait for emmc device /dev/mmcblk0p1e[00m + seq 6 + emmc_all_partition_exist=1 + [ ! -e /dev/mmcblk0p1 ] + emmc_all_partition_exist=1 + [ ! -e /dev/mmcblk0p2 ] + emmc_all_partition_exist=1 + [ ! -e /dev/mmcblk0p3 ] + emmc_all_partition_exist=1 + [ ! -e /dev/mmcblk0p4 ] + emmc_all_partition_exist=1 + [ ! -e /dev/mmcblk0p5 ] + emmc_all_partition_exist=1 + [ ! -e /dev/mmcblk0p6 ] + [ 1 -eq 0 ] + break + [ 1 -eq 0 ] + mount_rootfs + get_current_fw_entry + grep current_entry + fw_printenv + awk -F= {print $2} + local current_entry=0 + [ x0 = x ] + echo 0 + local current_entry=0 + local dev_rootfs= + [ 0 = 0 ] + findfs PARTLABEL=rootfs + dev_rootfs=/dev/mmcblk0p4 + echo_dbg rootfs boot from rootfs + echo -e \033[01;32mrootf[ 6.526591] EXT4-fs (mmcblk0p4): couldn't mount as ext3 due to feature incompatibilities [ 6.532961] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null) s boot from rootfs\033[00m e[01;32mrootfs boot from rootfse[00m + mkdir -p /mnt/rootfs + mount -o ro /dev/mmcblk0p4 /mnt/rootfs + mount_rootfs_data + findfs PARTLABEL=rootfs_data + local dev_rootfs_data=/dev/mmcblk0p9 + echo_dbg rootfs data: /dev/mmcblk0p9 + echo -e \033[01;32mr[ 6.884195] EXT4-fs (mmcblk0p9): couldn't mount as ext3 due to feature incompatibilities ootfs data: /dev/mmcblk0p9\033[00m e[01;32mrootfs data: /dev/mmcblk0p9e[00m + [ x/dev/mmcblk0p9 != x ] + [ -e /dev/mmcblk0p9 ] + blkid /dev/mmcblk0p9 + grep -q ext4 + echo_dbg Mount rootfs data to /mnt/rootfs_data + echo -e \033[01;32mMount rootfs data to /mnt/rootfs_data\033[00m e[01;32mMount rootfs data to /mnt/rootfs_datae[00m + mkdir -p /mnt/rootfs_data + mount /dev/mmcblk0p9 /mnt/rootfs_data [ 7.236964] EXT4-fs (mmcblk0p9): recovery complete [ 7.238250] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: (null) + [ ! -d /mnt/rootfs_data/etc ] + [ -e /mnt/rootfs_data/etc/reset_to_default ] + mount_usr_squahsfs + echo_dbg Mount usr.squahsfs to /mnt/rootfs_data/usr + echo -e \033[01;32mMount usr.squahsfs to /mnt/rootfs_data/usr\033[00m e[01;32mMount usr.squahsfs to /mnt/rootfs_data/usre[00m + [ ! -d /mnt/rootfs_data/usr ] + mount -t squashfs -o ro,loop /mnt/rootfs/usr.squashfs /mnt/rootfs_data/usr + check_and_restore_ubootenv + mount_reserved + findfs PARTLABEL=reserved [ 7.530081] random: nonblocking pool is initialized + dev_reserved=/dev/mmcblk0p8 + echo_dbg reserved partition from reserved + echo -e \033[01[ 7.602548] EXT4-fs (mmcblk0p8): couldn't mount as ext3 due to feature incompatibilities [ 7.608876] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null) ;32mreserved partition from reserved\033[00m e[01;32mreserved partition from reservede[00m + mkdir -p /mnt/reserved + mount -o ro /dev/mmcblk0p8 /mnt/reserved + [ -e /mnt/reserved/uboot-env.bin ] + fw_printenv + grep BMAC + awk -F= {print $2} + local BMAC=* + fw_printenv + grep MN + awk -F= {print $2} + local MN=A03 + fw_printenv + grep QSN + awk -F= {print $2} + local QSN=Q209Q01034 + fw_printenv + grep FWMode + awk -F= {print $2} + local FWMode=Normal + [ x245EBE529FDB == x ] + [ xA03 == x ] + [ xQ209Q01034 == x ] + [ xNormal == x ] + umount /mnt/reserved + get_fw_mode + fw_printenv + grep FWMode + awk -F= {print $2} + local FWMode=Normal + [ xNormal = x ] + echo Normal + fw_mode=Normal + [ Normal == Normal ] + fw_printenv + grep ipaddr + ipaddr_found= + [ x != x ] + fw_printenv + grep serverip + serverip_found= + [ x != x ] + fw_printenv + grep tftptimeoutcountmax + tftptimeoutcountmax_found= + [ x != x ] + echo watchdog close null + echo exit 0 + mount --move /sys /mnt/rootfs_data/sys + mount --move /proc /mnt/rootfs_data/proc + mount --move /dev /mnt/rootfs_data/dev + add_necessary_rootfs + [ ! -d /mnt/rootfs_data/run ] + mount -t tmpfs tmpfs /mnt/rootfs_data/run + [ ! -L /mnt/rootfs_data/var/run ] + mkdir -p /mnt/rootfs_data/run/lock + [ ! -L /mnt/rootfs_data/var/lock ] + [ ! -L /mnt/rootfs_data/etc/rc.common ] + [ ! -L /mnt/rootfs_data/etc/preinit ] + [ ! -L /mnt/rootfs_data/etc/hotplug-preinit.json ] + [ ! -L /mnt/rootfs_data/etc/hotplug.json ] + echo_dbg Switch to real root file system + echo -e \033[01;32mSwitch to real root file system\033[00m e[01;32mSwitch to real root file systeme[00m + exec switch_root /mnt/rootfs_data /sbin/init [ 8.014723] init: Console is alive [ 8.014803] init: - watchdog - [ 9.017321] init: - preinit - [ 9.127423] procd: - early - [ 9.127460] procd: - watchdog - [ 9.732603] procd: - ubus - [ 10.739257] procd: - init - (none) login: [ 10.903243] ssdk_switch_device_num_init[1084]:INFO:ess-switch dts node number: 1 [ 10.906999] ssdk_dt_get_switch_node[919]:INFO:ess-switch DT exist! [ 10.913945] ssdk_dt_parse_access_mode[820]:INFO:switch_access_mode: local bus [ 10.920103] ssdk_dt_parse_access_mode[833]:INFO:switchreg_base_addr: 0x3a000000 [ 10.927231] ssdk_dt_parse_access_mode[834]:INFO:switchreg_size: 0x1000000 [ 10.934534] ssdk_dt_parse_mac_mode[288]:INFO:mac mode = 0x0 [ 10.940934] ssdk_dt_parse_mac_mode[297]:INFO:mac mode1 = 0xd [ 10.946495] ssdk_dt_parse_mac_mode[306]:INFO:mac mode2 = 0xd [ 10.952132] ssdk_dt_parse_phy_info[564]:INFO:qcom,port_phyinfo DT doesn't exist! [ 10.957789] ssdk_dt_parse_mdio[678]:INFO:mdio DT exist! [ 10.964829] ssdk_dt_parse_uniphy[325]:INFO:ess-uniphy DT exist! [ 10.970446] ssdk_dt_parse_intf_mac[766]:INFO:dp1 MAC 24:5e:be:52:: [ 10.976312] ssdk_dt_parse_intf_mac[766]:INFO:dp2 MAC 24:5e:be:52:: [ 10.982793] ssdk_dt_parse_intf_mac[766]:INFO:dp3 MAC 24:5e:be:52:: [ 10.989304] ssdk_dt_parse_intf_mac[766]:INFO:dp4 MAC 24:5e:be:52:: [ 10.995820] ssdk_dt_parse_intf_mac[766]:INFO:dp5 MAC 24:5e:be:52:: [ 11.002325] ssdk_dt_parse_intf_mac[766]:INFO:dp6 MAC 24:5e:be:52:: [ 11.008832] ssdk_plat_init start [ 11.086286] ssdk_gcc_clock_init[629]:INFO:SSDK gcc clock init successfully! [ 11.089465] ssdk_probe[1922]:INFO:ess_rst doesn't exist! [ 11.096104] HPPE initializing... [ 11.097358] ssdk_phy_driver_init[292]:INFO:*port_id is 1, phy_addr is 10 [ 11.104751] ssdk_phy_driver_init[292]:INFO:*port_id is 2, phy_addr is 11 [ 11.112283] ssdk_phy_driver_init[292]:INFO:*port_id is 3, phy_addr is 12 [ 11.119837] ssdk_phy_driver_init[292]:INFO:*port_id is 4, phy_addr is 13 [ 11.127394] ssdk_phy_driver_init[292]:INFO:*port_id is 5, phy_addr is 8 [ 11.134968] ssdk_phy_driver_init[292]:INFO:*port_id is 6, phy_addr is 0 [ 11.142426] ssdk_phy_driver_init[292]:INFO:*port_id is 7, phy_addr is 6 [ 11.149870] ssdk_phy_driver_init[301]:INFO:dev_id = 0, phy_adress = 6, phy_id = 0xffffffff phytype doesn't match [ 11.157322] malibu_phy_api_ops_init[2849]:INFO:qca probe malibu phy driver succeeded! [ 11.170514] aquantia_phy_api_ops_init[2180]:INFO:qca probe aquantia phy driver succeeded! [ 11.176404] regi_init[3368]:INFO:Initializing HPPE!! [ 11.394235] ssdk_ppe_reset_init[860]:INFO:ppe reset successfully! [ 11.400213] qca_hppe_tdm_hw_init[674]:INFO:tdm setup num=96 [ 11.403558] qca_hppe_portctrl_hw_init[105]:INFO:Hawkeye PPE port initializing [ 14.934268] ssdk_switch_register[1631]:INFO:Chip version 0x1500 [ 14.937251] qca_link_polling_select[1281]:INFO:link-polling-required node does not exist [ 14.943488] ssdk_switch_register[1656]:INFO:polling is selected [ 14.951212] regi_init[3372]:INFO:Initializing HPPE Done!! [ 14.956128] regi_init[3423]:INFO:qca-ssdk module init succeeded! [ 14.970584] EDMA ver 1 hw init [ 14.970824] EDMA HW Reset completed succesfully [ 14.972553] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7) [ 14.977001] RxDesc:1 (15-15) RxFill:1 (7-7) [ 14.986850] [ 14.986875] * NSS Data Plane driver [ 14.992916] [ 15.022275] usbcore: registered new interface driver usbfs [ 15.022337] usbcore: registered new interface driver hub [ 15.026728] usbcore: registered new device driver usb [ 15.069491] msm-usb-ssphy-qmp 78000.ssphy: Initializing QMP phy [ 15.076342] msm-usb-ssphy-qmp 78000.ssphy: QMP PHY initialization timeout [ 15.076363] msm-usb-ssphy-qmp 78000.ssphy: USB3_PHY_PCS_STATUS:68686868 [ 15.283260] msm-usb-ssphy-qmp 58000.ssphy: Initializing QMP phy [ 15.290715] msm-usb-ssphy-qmp 58000.ssphy: QMP PHY initialization timeout [ 15.290736] msm-usb-ssphy-qmp 58000.ssphy: USB3_PHY_PCS_STATUS:68686868 [ 15.517049] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 15.517084] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 15.521559] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010 [ 15.529022] xhci-hcd xhci-hcd.0.auto: irq 211, io mem 0x08a00000 [ 15.538497] hub 1-0:1.0: USB hub found [ 15.544094] hub 1-0:1.0: 1 port detected [ 15.547693] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 15.551546] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 15.556878] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 15.565053] hub 2-0:1.0: USB hub found [ 15.572893] hub 2-0:1.0: 1 port detected [ 15.576534] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 15.580366] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 15.585831] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010 [ 15.593240] xhci-hcd xhci-hcd.1.auto: irq 212, io mem 0x08c00000 [ 15.602594] hub 3-0:1.0: USB hub found [ 15.608163] hub 3-0:1.0: 1 port detected [ 15.611859] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 15.615795] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 15.621105] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 15.628945] hub 4-0:1.0: USB hub found [ 15.636991] hub 4-0:1.0: 1 port detected [ 15.655386] SCSI subsystem initialized [ 15.668047] usbcore: registered new interface driver usb-storage [ 15.690177] ntfs: driver 2.1.32 [Flags: R/O MODULE]. [ 15.700726] fuse init (API version 7.23) [ 15.727911] diag: IPC Logging disabled [ 15.728291] TRACK: P[0] PMask[4] [ 15.730538] TRACK: P[1] PMask[4] [ 15.733923] TRACK: P[2] PMask[4] [ 15.737319] TRACK: P[3] PMask[4] [ 15.740390] nik 4097 info→svc_id [ 15.874351] nss_driver - fw of size 739972 bytes copied to load addr: 40000000, nss_id : 0 [ 15.876037] Supported Frequencies - [ 15.881494] 748.8 MHz 1.4976 GHz [ 15.887478] 1.6896 GHz [ 15.888522] [ 15.890884] ffffffbffc580080: set sdma ffffffc03c301600 [ 15.892410] ffffffbffc580080: meminfo init succeed [ 15.926518] node size 2 # items 4 [ 15.926542] memory: 40000000 1073741824 (avl 931807232) items 4 active_cores 2 [ 15.928838] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 [ 15.935950] ffffffbffc580080: nss core 0 booted successfully [ 15.943911] nss_driver - fw of size 289444 bytes copied to load addr: 40800000, nss_id : 1 [ 15.951273] Supported Frequencies - [ 15.956789] 748.8 MHz 1.4976 GHz [ 15.962763] 1.6896 GHz [ 15.963821] [ 15.966733] ffffffbffc587600: set sdma ffffffc03b282a00 [ 15.967830] ffffffbffc587600: meminfo init succeed [ 15.976844] node size 2 # items 4 [ 15.977327] memory: 40000000 1073741824 (avl 931831808) items 4 active_cores 2 [ 15.980849] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 [ 15.987911] ffffffbffc587600: nss core 1 booted successfully [ 15.989077] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 16.069888] PPP generic driver version 2.4.2 [ 16.077114] l2tp_core: L2TP core driver, V2.0 [ 16.117783] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded. [ 16.147272] NET: Registered protocol family 24 [ 16.177459] QCA multicast snooping installed successfully [ 16.183640] <NSS-CRYPTO>:module loaded Build_ID - 04/28/21, 21:26:33 SoC=ipq807x_64 [ 16.193535] cannot find nss-macsec0 node [ 16.193591] cannot find nss-macsec1 node [ 16.196553] cannot find nss-macsec2 node [ 16.200417] nss_macsec init success [ 16.531322] sit: IPv6 over IPv4 tunneling driver /usr/bin/iotd[698]: Started iot daemon qcawifi configuration is disable [ 38.551662] configuring additional NSS pbufs [ 38.577895] additional pbufs of size 9003008 got added to NSS [ 38.615688] cfg80211: World regulatory domain updated: [ 38.615715] cfg80211: DFS Master region: unset [ 38.619763] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 38.624346] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 38.634024] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 38.641822] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 38.651155] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 38.659109] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 38.668850] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 38.674687] mem_manager: module license 'Proprietary' taints kernel. [ 38.674689] Disabling lock debugging due to kernel taint [ 38.692780] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 38.697965] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 38.971615] wlan: [801:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50 *starting cnssdaemon* *initiating cold boot calibration* *cnssdaemon pid=834* [ 39.231028] wlan: [839:I:ANY]
ol_if_register_wifi3_0
[ 39.231028] [ 39.231063] wlan: [839:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd0f05a0 [ 39.237876] wlan: [839:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 2 bus_type 1 [ 39.249571] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss [ 39.263503] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 39.950245] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up [ 39.950312] wlan: [839:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 3 bus_type 1 [ 39.950705] rpmsg_dev_probe: No pm domain [ 39.950911] rpmsg_dev_probe: No pm domain [ 39.969519] cnss: QMI WLFW service connected, state: 0x1 [ 39.969520] wlan: [839:I:ANY] ol_ath_check_fw_ready: 614: Waiting for FW ready device fffe [ 39.973454] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, ffffffbffc443248 [ 39.987184] cnss: device_id : 65534 mem mode : [0] [ 40.039410] cnss: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x220284a5, fw_build_timestamp: 2020-06-05 00:18, otp_version: 0x0 eeprom_caldata_read_timeout 0s [ 40.039493] cnss: Downloading BDF: bdwlan.bin, size: 64 [ 40.057456] cnss: No board_id entry in device tree [ 40.064798] cnss: BDF location : 0x4b0c0000 [ 40.067339] cnss: BDF IPQ8074/bdwlan.bin size 131072 [ 40.071718] cnss: Downloading BDF: caldata.bin, size: 64 [ 40.076879] cnss: per device BDF location : 0x4b0e0000 [ 40.082007] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000 [ 40.184247] wlan: [839:I:ANY] ol_ath_check_fw_ready: 624: FW ready received for device fffe [ 40.185308] wlan: [839:I:ANY] pld_ahb_wlan_enable: 691: cnss_mode: Cold boot calibration [ 40.267261] wlan: [839:I:ANY] Coldboot calibration wait started [ 40.267261] [ 40.767318] wlan: [839:I:ANY] Coldboot calibration wait ended [ 40.767318] [ 40.768998] wlan: [839:I:ANY] ol_ath_do_cold_boot_calibration: 598: Coldboot calib successful: radio_id 0x65534 [ 40.769139] cnss: QMI WLFW service disconnected, state: 0x6 [ 40.783943] wlan: [839:I:ANY] init_ath_pci_3_0: 179: 6ath_ol_pci_wifi3.0 : (Atheros/multi-bss) [ 40.792553] wlan: [845:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 0 bus_type 1 [ 40.823848] remoteproc remoteproc0: stopped remote processor cd00000.qcom_q6v5_wcss [ 40.823900] wlan: [845:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 1 bus_type 1 [ 41.084200] wlan: [852:I:ANY]
ol_if_register_wifi3_0
[ 41.084200] [ 41.084265] wlan: [852:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd4275a0 [ 41.091030] wlan: [852:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 2 bus_type 1 [ 41.102745] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss [ 41.111198] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 41.469359] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up [ 41.469423] wlan: [852:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 3 bus_type 1 [ 41.469773] rpmsg_dev_probe: No pm domain [ 41.469924] rpmsg_dev_probe: No pm domain [ 41.488547] wlan: [852:I:ANY] ol_ath_check_fw_ready: 614: Waiting for FW ready device fffe [ 41.488832] cnss: QMI WLFW service connected, state: 0x1 [ 41.489252] cnss: device_id : 65534 mem mode : [0] [ 41.490284] cnss: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x220284a5, fw_build_timestamp: 2020-06-05 00:18, otp_version: 0x0 eeprom_caldata_read_timeout 0s [ 41.490290] cnss: Downloading BDF: bdwlan.bin, size: 64 [ 41.490295] cnss: No board_id entry in device tree [ 41.490501] cnss: BDF location : 0x4b0c0000 [ 41.490502] cnss: BDF IPQ8074/bdwlan.bin size 131072 [ 41.490765] cnss: Downloading BDF: caldata.bin, size: 64 [ 41.490944] cnss: per device BDF location : 0x4b0e0000 [ 41.490990] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000 [ 41.559242] wlan: [852:I:ANY] ol_ath_check_fw_ready: 624: FW ready received for device fffe [ 41.566518] wlan: [852:I:ANY] pld_ahb_wlan_enable: 699: cnss_mode: Mission mode [ 41.582976] wlan: [852:I:ANY] qca_napi_create: 364: qca_napi_create: napi instance 0 created on pipe 4 [ 41.583164] wlan: [852:I:ANY] ol_ath_attach: 3920: Allocated soc ffffffc032900880 [ 41.592176] wlan: [852:E:CONFIG] cfg_uint_item_handler: 171: dp_int_timer_threshold_tx=1000 - Out of range [8, 100]; Using 1000 [ 41.598978] wlan: [852:I:ANY] osif_nss_wifi_soc_setup: 192: nss-wifili:#1 register wifili function for soc [ 41.610186] wlan: [852:I:ANY] osif_nss_wifi_soc_setup: 204: nss register id -1 nss config 3 Target Type 18 [ 41.619920] wlan: [852:I:ANY] ol_ath_attach: 4127: dev name soc0 [ 41.629769] wlan: [852:I:ANY] ol_ath_soc_attach: 7157: WMI attached. wmi_handle ffffffc03d785800 [ 41.635957] wlan: [852:I:ANY] htc_wmi_init: 6167: htc_wmi_init() HT Create . ffffffc034ff3000 [ 41.644819] wlan: [852:I:ANY] htc_wmi_init: 6174: htc_wmi_init() Skipping BMI Done. [ 41.653319] wlan: [852:I:ANY] htc_wmi_init: 6231: [htc_wmi_init:6231] host_enable 0 nss_nwifi_offload 0 [ 41.663832] wlan: [852:I:ANY] ol_target_init_complete: 6353: CDP soc attach success [ 41.670261] wlan: [852:I:ANY] ol_target_init_complete: 6360: Soc attach success NSS config 0 [ 41.677935] wlan: [852:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc034ff3000, ep 2, value 1 [ 41.686612] wlan: [852:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc034ff3000, ep 3, value 1 [ 41.697177] wlan: [855:I:TIF] HE_CAP Info = 1a08010d [ 41.707057] wlan: [855:I:TIF] Num HW modes = 1 [ 41.712077] wlan: [855:I:TIF] Num PHY = 2 [ 41.716337] wlan: [855:I:TIF] Preferred HW Mode = 1 Num Radios = 2 [ 41.720417] wlan: [855:I:TIF] init_deinit_add_11ax_modes: 1779: Adding 11ax regulatory modes, [ 41.726501] wlan: [855:I:TIF] init_deinit_add_11ax_modes: 1783: phy_id = 0 wireless modes = f97f9001 [ 41.735095] wlan: [855:I:TIF] init_deinit_add_11ax_modes: 1779: Adding 11ax regulatory modes, [ 41.744296] wlan: [855:I:TIF] init_deinit_add_11ax_modes: 1783: phy_id = 1 wireless modes = 680680c [ 41.752800] wlan: [855:I:TIF] init_deinit_add_11ax_modes: 1806: hw_mode_id = 1 phy_id = 0 wireless modes = f97f9001 [ 41.762011] wlan: [855:I:TIF] init_deinit_add_11ax_modes: 1806: hw_mode_id = 1 phy_id = 1 wireless modes = 680688c [ 41.772409] wlan: [855:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 421: dfs_offload 1 [ 41.782582] wlan: [855:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 2850: dfs→dfs_psoc_idx: 0 [ 41.792561] wlan: [855:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 2856: dfs_soc_obj→num_dfs_privs: 1 [ 41.802484] wlan: [855:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 393: Do not allocate DFS object for 2G, pdev_id = 1 [ 41.812568] wlan: [855:I:ANY] init_deinit_update_pdev_tgt_info: 1347: pdev id:0 wmi_handle:ffffffc03d785800 [ 41.831521] wlan: [855:I:ANY] init_deinit_update_pdev_tgt_info: 1403: Pdev = 0 Number of peers = 529 vdevs = 17 [ 41.835123] wlan: [855:I:TIF] init_deinit_update_pdev_tgt_info: 1406: CDP PDEV ATTACH success [ 41.845290] wlan: [855:I:ANY] init_deinit_update_pdev_tgt_info: 1347: pdev id:1 wmi_handle:ffffffc0378a5400 [ 41.856323] wlan: [855:I:ANY] init_deinit_update_pdev_tgt_info: 1403: Pdev = 1 Number of peers = 529 vdevs = 17 [ 41.863392] wlan: [855:I:TIF] init_deinit_update_pdev_tgt_info: 1406: CDP PDEV ATTACH success [ 41.973830] wlan: [855:I:ANY] copy_fw_abi_version_tlv: 6960: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0 [ 42.193765] wlan: [855:I:ANY] ready_extract_init_status_tlv: 9002: ready_extract_init_status_tlv:0 [ 42.193796] wlan: [855:I:ANY] dp_peer_map_attach_wifi3: 9799: dp_peer_map_attach_wifi3 max_peers 1109, max_ast_index: 4112 [ 42.193796] [ 42.201812] wlan: [852:I:ANY] ol_ath_connect_htc: 1216: WMI is ready [ 42.265946] wlan: [852:E:TIF] target_if_lro_hash_config: 254: pdev with id 0 is NULL [ 42.268564] wlan: [852:E:TIF] target_if_lro_hash_config: 254: pdev with id 1 is NULL [ 42.273033] wlan: [852:I:ANY] ol_ath_soc_attach: 7248: connect HTC [ 42.280512] wlan: [852:I:ANY] ol_ath_soc_attach: 7249: bypasswmi : 0 [ 42.286482] wlan: [852:I:ANY] ol_ath_soc_attach: 7323: ol_ath_soc_attach() UMAC attach . [ 42.293053] wlan: [852:I:ANY] ol_ath_attach: 4240: pdev_netdev name wifi0 [ 42.301061] wlan: [852:I:ANY] ol_ath_attach: 4287: Skip txrx_pdev_attach_target [ 42.307822] wlan: [852:I:ANY] ol_ath_attach: 4313: BURSTING enabled by default [ 42.315512] wlan: [852:I:ANY] ol_ath_pdev_attach: 9110: interface_id 0 [ 42.322927] wlan: [852:I:TIF] ol_ath_pdev_regdmn_init: 7477: phy id = 0 Modes supported [ 42.329264] wlan: [852:I:TIF] ol_ath_pdev_regdmn_init: 7484: 11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1 [ 42.337515] wlan: [852:I:TIF] ol_ath_pdev_regdmn_init: 7493: Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4900, hi_5g = 6100 [ 42.347332] wlan: [852:I:ANY] ol_ath_update_wireless_modes: 1346: wireless_modes = f97f9001 before update [ 42.361905] wlan: [852:I:ANY] ol_ath_update_wireless_modes: 1362: Wireless_modes = f97f9001 after update [ 42.371540] wlan: [852:I:ANY] ol_ath_update_ext_caps: 1944: 11ax 5G supported case [ 42.381192] wlan: [852:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed [ 42.388580] wlan: [852:I:ANY] acfg_attach: 3519: acfg_attach: 3519: Netlink socket created:ffffffc02d1c0400 [ 42.394985] wlan: [852:I:ANY] ol_ath_stats_attach: 2275: periodic_chan_stats: 1 [ 42.405575] wlan: [852:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 25 [ 42.411933] wlan: [0:I:ANY] ol_ath_pdev_attach: 9454: Set global_ic[1], ptr:ffffffbffcbff8e8 [ 42.419197] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc0378a6008) Enabling DBDC Repeater 1 [ 42.427895] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(ffffffc0378a6008) is_primary 1 [ 42.427971] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 42.445987] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 14683: twt enabled. [ 42.445987] [ 42.447189] wlan: [852:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 543: cfg block channel list is empty [ 42.447192] wlan: [852:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3848: pdev_idx = 0 tx_desc_limit = 32768 [ 42.447205] wlan: [852:I:ANY] osif_wrap_attach: 239: osif wrap attached [ 42.447205] [ 42.447208] wlan: [852:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done [ 42.447208] [ 42.447212] wlan: [852:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc02d1c0800 ic→ic_wrap_com=ffffffc02d1c0800 &wrap_com→wc_devt=ffffffc02d1c0800 [ 42.447212] [ 42.447233] wlan: [852:I:ANY] ol_ath_attach: 4483: needed_headroom reservation 60 [ 42.447237] wlan: [852:I:ANY] ol_ath_enable_fraglist: 3272: Enabled Fraglist bit for the radio wifi0 features 41 [ 42.447450] wlan: [852:I:ANY] ieee80211_cfg80211_radio_attach: 11804: ic: 0xffffffc032680880, wdev: 0xffffffc032698a58, wiphy: 0xffffffc0357d6aa0, netdev: 0xffffffc032680000 [ 42.447909] wlan: [852:I:ANY] ol_ath_attach: 4240: pdev_netdev name wifi1 [ 42.447923] wlan: [852:I:ANY] ol_ath_attach: 4287: Skip txrx_pdev_attach_target [ 42.447927] wlan: [852:I:ANY] ol_ath_attach: 4313: BURSTING enabled by default [ 42.447965] wlan: [852:I:ANY] ol_ath_pdev_attach: 9110: interface_id 1 [ 42.447976] wlan: [852:I:TIF] ol_ath_pdev_regdmn_init: 7477: phy id = 1 Modes supported [ 42.447980] wlan: [852:I:TIF] ol_ath_pdev_regdmn_init: 7484: 11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1 [ 42.447984] wlan: [852:I:TIF] ol_ath_pdev_regdmn_init: 7493: Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0 [ 42.447986] wlan: [852:I:ANY] ol_ath_update_wireless_modes: 1346: wireless_modes = 680680c before update [ 42.447989] wlan: [852:I:ANY] ol_ath_update_wireless_modes: 1362: Wireless_modes = 680680c after update [ 42.447993] wlan: [852:I:ANY] ol_ath_update_ext_caps: 1952: 11ax 2G supported case [ 42.448081] wlan: [852:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed [ 42.448192] wlan: [852:I:ANY] acfg_attach: 3494: Offload using existing sock ffffffc02d1c0400 [ 42.448200] wlan: [852:I:ANY] ol_ath_stats_attach: 2275: periodic_chan_stats: 1 [ 42.448367] wlan: [852:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 11 [ 42.448391] wlan: [0:I:ANY] ol_ath_pdev_attach: 9454: Set global_ic[2], ptr:ffffffbffcbff8e8 [ 42.448396] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc0378a5008) Enabling DBDC Repeater 1 [ 42.448420] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(ffffffc0378a5008) is_primary 0 [ 42.449884] wlan: [852:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 543: cfg block channel list is empty [ 42.449888] wlan: [852:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3848: pdev_idx = 1 tx_desc_limit = 32768 [ 42.449901] wlan: [852:I:ANY] osif_wrap_attach: 239: osif wrap attached [ 42.449901] [ 42.449903] wlan: [852:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done [ 42.449903] [ 42.449907] wlan: [852:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc02d1c3400 ic→ic_wrap_com=ffffffc02d1c3400 &wrap_com→wc_devt=ffffffc02d1c3400 [ 42.449907] [ 42.449921] wlan: [852:I:ANY] ol_ath_attach: 4483: needed_headroom reservation 60 [ 42.449925] wlan: [852:I:ANY] ol_ath_enable_fraglist: 3272: Enabled Fraglist bit for the radio wifi1 features 41 [ 42.449940] wlan: [852:I:ANY] wlan_cfg80211_init: 11678: Number of 2G channels: 11 [ 42.450070] wlan: [852:I:ANY] ieee80211_cfg80211_radio_attach: 11804: ic: 0xffffffc0326c0880, wdev: 0xffffffc0326d8a58, wiphy: 0xffffffc02ceaa2a0, netdev: 0xffffffc0326c0000 [ 42.450427] wlan: [852:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3817: Running with HW mode = 1 [ 42.450612] wlan: [852:E:QLD] qld_register: 108: Handle or address is NULL [ 42.450625] wlan: [852:I:ANY] wlan_pdev_operation: 727: num_radios=1, wifi_radios[0].sc = ffffffc032680880_radio_type = 2 [ 42.450629] wlan: [852:I:ANY] wlan_pdev_operation: 727: num_radios=2, wifi_radios[1].sc = ffffffc0326c0880_radio_type = 2 [ 42.450648] wlan: [852:I:ANY] init_ath_pci_3_0: 179: 6ath_ol_pci_wifi3.0 : (Atheros/multi-bss) [ 42.826098] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 42.835469] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 14683: twt enabled. [ 42.835469] [ 42.885079] wlan: [858:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd522e60 [ 42.885438] wlan: [858:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0: (Atheros/multi-bss) No Direct-Attach chipsets found. acfg_tool: Issuing blocking call to wait for events [ 43.756790] gre: GRE over IPv4 demultiplexor driver [ 43.761991] l2tp_netlink: L2TP netlink interface [ 43.762923] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 43.771127] PPTP driver version 0.8.5 [ 43.830179] ECM init [ 43.830233] ECM database jhash random seed: 0x813c8e66 [ 43.831660] ECM Connection maximum number: 8192 [ 43.847044] ECM init complete acfg_tool: Issuing blocking call to wait for events [ 46.102545] ctnetlink v0.93: registering with nfnetlink. [ 46.455184] xt_time: kernel timezone is -0000 [ 46.466258] arp_tables: (C) 2002 David S. Miller [ 46.703778] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 46.836279] Ebtables v2.0 registered [ 47.107421] swdev1: renamed from eth3 [ 47.135282] IPv6: ADDRCONF(NETDEV_UP): swdev1: link is not ready [ 47.136609] swdev2: renamed from eth2 [ 47.195227] IPv6: ADDRCONF(NETDEV_UP): swdev2: link is not ready [ 47.196488] swdev3: renamed from eth1 [ 47.235190] IPv6: ADDRCONF(NETDEV_UP): swdev3: link is not ready [ 47.236465] swdev4: renamed from eth0 [ 47.275220] IPv6: ADDRCONF(NETDEV_UP): swdev4: link is not ready [ 47.276485] swdev5: renamed from eth4 [ 47.315230] IPv6: ADDRCONF(NETDEV_UP): swdev5: link is not ready [ 47.316494] swdev6: renamed from eth5 [ 47.355248] IPv6: ADDRCONF(NETDEV_UP): swdev6: link is not ready [ 48.005712] ipip: IPv4 over IPv4 tunneling driver [ 48.264140] ifb4: renamed from ifb2 [ 48.374639] network.sh wrote to bridge-nf-call-iptables when file position was not 0! [ 48.374639] This will not be supported in the future. To silence this [ 48.374639] warning, set kernel.sysctl_writes_strict = -1 [ 48.965505] PPP MPPE Compression module registered [ 52.475947] device swdev2 entered promiscuous mode [ 52.490995] device swdev3 entered promiscuous mode [ 52.505578] device swdev4 entered promiscuous mode [ 52.519567] device swdev5 entered promiscuous mode [ 52.531990] IPv6: ADDRCONF(NETDEV_UP): swdev6.3: link is not ready [ 52.532560] device swdev6 entered promiscuous mode [ 52.543425] device swdev6.3 entered promiscuous mode [ 52.548203] IPv6: ADDRCONF(NETDEV_UP): swdev6.6: link is not ready [ 52.554806] device swdev6.6 entered promiscuous mode [ 52.559761] IPv6: ADDRCONF(NETDEV_UP): swdev6.7: link is not ready [ 52.566754] device swdev6.7 entered promiscuous mode [ 52.571393] IPv6: ADDRCONF(NETDEV_UP): swdev6.8: link is not ready [ 52.578858] device swdev6.8 entered promiscuous mode [ 59.243651] br_v0: port 1(swdev2) entered disabled state [ 59.245703] br_v0: port 2(swdev3) entered disabled state [ 59.249812] br_v0: port 3(swdev4) entered disabled state [ 59.255275] br_v0: port 4(swdev5) entered disabled state [ 64.260202] IPv6: ADDRCONF(NETDEV_UP): swdev2: link is not ready [ 64.260704] IPv6: ADDRCONF(NETDEV_UP): swdev3: link is not ready [ 64.266223] IPv6: ADDRCONF(NETDEV_UP): swdev4: link is not ready [ 64.271976] IPv6: ADDRCONF(NETDEV_UP): swdev5: link is not ready [ 64.345622] br_v3: port 1(swdev6.3) entered disabled state [ 69.346906] IPv6: ADDRCONF(NETDEV_UP): swdev6.3: link is not ready [ 69.482718] br_v6: port 1(swdev6.6) entered disabled state
Login timed out after 60QHora301W529FDB login: [ 74.484132] IPv6: ADDRCONF(NETDEV_UP): swdev6.6: link is not ready [ 74.549916] br_v7: port 1(swdev6.7) entered disabled state [ 79.551198] IPv6: ADDRCONF(NETDEV_UP): swdev6.7: link is not ready [ 79.619825] br_v8: port 1(swdev6.8) entered disabled state [ 84.621151] IPv6: ADDRCONF(NETDEV_UP): swdev6.8: link is not ready [ 84.954605] NET: Registered protocol family 15 [ 84.985220] Initializing XFRM netlink socket lbd: require both 2.4 GHz and 5 GHz to be configured. Aborting start. lbd: stopping daemon lbd: stopping daemon qcawifi qcawificfg80211 disable radio wifi0 qcawifi qcawificfg80211 disable radio wifi1 qcawifi qcawificfg80211: enable radio wifi0 [ 91.748038] wlan: [4183:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 19 [ 91.748293] wlan: [4183:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=58 [ 91.754524] wlan: [4183:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=106 [ 91.762863] wlan: [4183:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=122 [ 91.771670] wlan: [4183:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 19 [ 91.779261] wlan: [4183:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=58 [ 91.786798] wlan: [4183:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=106 [ 91.794869] wlan: [4183:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=122 [ 91.803143] wlan: [4183:I:ANY] number of channels: 2G = 0 5G = 19, 6G = 0 [ 91.811449] wlan: [4183:I:ANY] wlan_cfg80211_set_country: 6518: wlan_cfg80211_set_country: Country: DE ret: 0 [ 91.818430] wlan: [1175:I:ANY] ol_acfg_handle_wifi_ioctl: 446: ol_acfg_handle_wifi_ioctl: req→cmd=76 not valid for radio interface, it's for VAP Error received: -22 Could not send NL command [ 91.948513] wlan: [4202:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 2 Max_mac_rings 1 [ 91.948580] wlan: [4202:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 1 Max_mac_rings 1 [ 91.992362] wlan: [4206:I:ANY] wlan_cfg80211_set_hwaddr: 6591: wlan_cfg80211_set_hwaddr :24:5e:be:52:: ret: 0 [ 92.012882] wlan: [4208:I:ANY] ol_ath_set_config_param: 1640: set TXBF_SND_PERIOD: value 100 wmi_status 0 [ 92.074973] wlan: [0:I:ANY] ol_ath_set_config_param: 2392: Disconnect_timeout value: 10 [ 92.097787] wlan: [0:I:ANY] ol_ath_set_config_param: 2398: Reconfiguration_timeout value:60 number of vifs: vap2 vap4 vap6 vap8 [ 92.357683] wlan: [4315:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath0 : clone params: 0x00000001 [ 92.357755] wlan: [4315:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create 24:5e:be:52:: [ 92.368775] wlan: [4315:I:ANY] wlan_vap_create: 1599: devhandle=0xffffffc032680880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 92.368775] [ 92.377184] wlan: [4315:I:ANY] ol_ath_vap_set_param: 1208: Setting SGI value: 1 [ 92.389272] wlan: [4315:I:ANY] ol_ath_vap_set_param: 2240: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 92.396372] wlan: [4315:I:ANY] ol_ath_vap_set_param: 2253: he_bf_cap=0x7b [ 92.411643] wlan: [4315:I:ANY] ol_ath_vap_set_param: 2268: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 92.418459] wlan: [4315:I:ANY] MBO Initialized [ 92.432461] wlan: [4315:I:ANY] OCE Initialized [ 92.436812] wlan: [4315:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 40 nss_id -1 [ 92.441231] wlan: [4315:I:ANY] NSS radio_if 28 [ 92.450917] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0 [ 92.455224] wlan: [4315:I:ANY] osif_nss_ol_vap_create: 1393: vap create ffffffc026f0c880 : if_num 40 [ 92.463686] wlan: [4315:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 92.472838] wlan: [4315:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 92.482006] wlan: [4315:I:ANY] VAP device ath0 created osifp: (ffffffc026f0c880) os_if: (ffffffc0201c0000) [ 92.916937] wlan: [4361:I:ANY] wlan_set_param: 3031: HE MU BFER already set with this value =1 [ 93.018595] 8021q: adding VLAN 0 to HW filter on device ath0 [ 93.019884] device ath0 entered promiscuous mode [ 93.023511] br_v8: port 2(ath0) entered forwarding state [ 93.028016] br_v8: port 2(ath0) entered forwarding state [ 93.174804] wlan: [1184:I:ANY] DES SSID SET=C [ 93.174831] wlan: [1184:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 31 [ 93.202429] wlan: [4414:E:ANY] ieee80211_ucfg_set_txpow: 1027: Exceeding Max Tx power of 23 [ 93.209698] wlan: [0:I:CMN_MLME] vdev[0] ieee chan:100 freq:5500 [ 93.209915] wlan: [0:I:ANY] vdev[0]: Mgt Rate:6000(kbps) [ 93.216375] wlan: [34:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5500. [ 93.216375] [ 93.221409] wlan: [34:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5520. [ 93.221409] [ 93.228569] wlan: [4424:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath01 : clone params: 0x00000001 [ 93.228601] wlan: [4424:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create 2a:5e:be:52:: [ 93.228638] wlan: [4424:I:ANY] wlan_vap_create: 1599: devhandle=0xffffffc032680880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 93.228638] [ 93.243370] wlan: [4424:I:ANY] ol_ath_vap_set_param: 1208: Setting SGI value: 1 [ 93.243450] wlan: [4424:I:ANY] ol_ath_vap_set_param: 2240: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 93.243452] wlan: [4424:I:ANY] ol_ath_vap_set_param: 2253: he_bf_cap=0x7b [ 93.243463] wlan: [4424:I:ANY] ol_ath_vap_set_param: 2268: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 93.243501] wlan: [4424:I:ANY] MBO Initialized [ 93.243503] wlan: [4424:I:ANY] OCE Initialized [ 93.243522] wlan: [4424:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 41 nss_id -1 [ 93.243548] wlan: [4424:I:ANY] NSS radio_if 28 [ 93.255340] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0 [ 93.255350] wlan: [4424:I:ANY] osif_nss_ol_vap_create: 1393: vap create ffffffc026f08880 : if_num 41 [ 93.255579] wlan: [4424:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 93.255582] wlan: [4424:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 93.256368] wlan: [4424:I:ANY] VAP device ath01 created osifp: (ffffffc026f08880) os_if: (ffffffc020298000) [ 93.374217] wlan: [34:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5540. [ 93.374217] [ 93.383857] wlan: [34:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5560. [ 93.383857] [ 93.395035] wlan: [34:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5640. [ 93.395035] [ 93.406178] wlan: [34:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5620. [ 93.406178] [ 93.417174] wlan: [34:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5600. [ 93.417174] [ 93.428285] wlan: [34:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5580. [ 93.428285] [ 93.796425] wlan: [4533:I:ANY] wlan_set_param: 3031: HE MU BFER already set with this value =1 [ 93.924979] 8021q: adding VLAN 0 to HW filter on device ath01 [ 93.926125] device ath01 entered promiscuous mode [ 93.929851] br_v7: port 2(ath01) entered forwarding state [ 93.934428] br_v7: port 2(ath01) entered forwarding state [ 94.044681] wlan: [1184:I:ANY] DES SSID SET=C [ 94.044709] wlan: [1184:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 31 [ 94.049016] wlan: [0:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_set_current_channel_for_freq: 879: dfs_curchan already updated [ 94.082334] wlan: [0:I:CMN_MLME] vdev[1] ieee chan:100 freq:5500 [ 94.082510] wlan: [0:I:ANY] vdev[1]: Mgt Rate:6000(kbps) [ 94.108591] wlan: [4609:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath02 : clone params: 0x00000001 [ 94.108669] wlan: [4609:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create 2e:5e:be:52:: [ 94.119756] wlan: [4609:I:ANY] wlan_vap_create: 1599: devhandle=0xffffffc032680880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 94.119756] [ 94.128307] wlan: [4609:I:ANY] ol_ath_vap_set_param: 1208: Setting SGI value: 1 [ 94.140339] wlan: [4609:I:ANY] ol_ath_vap_set_param: 2240: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 94.147420] wlan: [4609:I:ANY] ol_ath_vap_set_param: 2253: he_bf_cap=0x7b [ 94.162707] wlan: [4609:I:ANY] ol_ath_vap_set_param: 2268: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 94.169491] wlan: [4609:I:ANY] MBO Initialized [ 94.183508] wlan: [4609:I:ANY] OCE Initialized [ 94.187854] wlan: [4609:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 42 nss_id -1 [ 94.192239] wlan: [4609:I:ANY] NSS radio_if 28 [ 94.201960] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0 [ 94.206232] wlan: [4609:I:ANY] osif_nss_ol_vap_create: 1393: vap create ffffffc026f0a880 : if_num 42 [ 94.214720] wlan: [4609:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 94.223821] wlan: [4609:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 94.233829] wlan: [4609:I:ANY] VAP device ath02 created osifp: (ffffffc026f0a880) os_if: (ffffffc0203a0000) [ 94.838775] wlan: [4708:I:ANY] wlan_set_param: 3031: HE MU BFER already set with this value =1 [ 94.965905] 8021q: adding VLAN 0 to HW filter on device ath02 [ 94.967642] device ath02 entered promiscuous mode [ 94.971026] br_v8: port 3(ath02) entered forwarding state [ 94.975361] br_v8: port 3(ath02) entered forwarding state [ 95.084640] wlan: [1184:I:ANY] DES SSID SET=C [ 95.084667] wlan: [1184:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 31 [ 95.089189] wlan: [0:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_set_current_channel_for_freq: 879: dfs_curchan already updated [ 95.104385] wlan: [0:I:CMN_MLME] vdev[2] ieee chan:100 freq:5500 [ 95.107264] wlan: [0:I:ANY] vdev[2]: Mgt Rate:6000(kbps) [ 95.138802] wlan: [4789:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: gt0 : clone params: 0x00000001 [ 95.138873] wlan: [4789:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create 32:5e:be:52:: [ 95.150140] wlan: [4789:I:ANY] wlan_vap_create: 1599: devhandle=0xffffffc032680880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 95.150140] [ 95.158253] wlan: [4789:I:ANY] ol_ath_vap_set_param: 1208: Setting SGI value: 1 [ 95.170344] wlan: [4789:I:ANY] ol_ath_vap_set_param: 2240: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 95.177418] wlan: [4789:I:ANY] ol_ath_vap_set_param: 2253: he_bf_cap=0x7b [ 95.192701] wlan: [4789:I:ANY] ol_ath_vap_set_param: 2268: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 95.199515] wlan: [4789:I:ANY] MBO Initialized [ 95.213510] wlan: [4789:I:ANY] OCE Initialized [ 95.217856] wlan: [4789:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 43 nss_id -1 [ 95.222266] wlan: [4789:I:ANY] NSS radio_if 28 [ 95.232010] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0 [ 95.236267] wlan: [4789:I:ANY] osif_nss_ol_vap_create: 1393: vap create ffffffc03be28880 : if_num 43 [ 95.244746] wlan: [4789:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 95.253860] wlan: [4789:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 95.263880] wlan: [4789:I:ANY] VAP device gt0 created osifp: (ffffffc03be28880) os_if: (ffffffc01b848000) [ 95.777640] wlan: [4874:I:ANY] wlan_set_param: 3031: HE MU BFER already set with this value =1 [ 95.903537] 8021q: adding VLAN 0 to HW filter on device gt0 [ 95.904463] device gt0 entered promiscuous mode [ 95.908096] br_v4094: port 1(gt0) entered forwarding state [ 95.912481] br_v4094: port 1(gt0) entered forwarding state [ 95.935345] wlan: [1184:I:ANY] DES SSID SET=C [ 95.935375] wlan: [1184:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 31 [ 95.939678] wlan: [0:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_set_current_channel_for_freq: 879: dfs_curchan already updated [ 95.976322] wlan: [0:I:CMN_MLME] vdev[3] ieee chan:100 freq:5500 [ 95.976502] wlan: [0:I:ANY] vdev[3]: Mgt Rate:6000(kbps) qcawifi qcawificfg80211: enable radio wifi1 [ 96.417475] wlan: [5042:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 13 [ 96.417607] wlan: [5042:I:ANY] number of channels: 2G = 13 5G = 0, 6G = 0 [ 96.424402] wlan: [5042:I:ANY] wlan_cfg80211_set_country: 6518: wlan_cfg80211_set_country: Country: DE ret: 0 [ 96.590076] wlan: [5066:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 2 Max_mac_rings 1 [ 96.590431] wlan: [5066:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 1 Max_mac_rings 1 [ 96.666622] wlan: [5082:I:ANY] wlan_cfg80211_set_hwaddr: 6591: wlan_cfg80211_set_hwaddr :24:5e:be:52:: ret: 0 [ 96.700559] wlan: [5092:I:ANY] ol_ath_set_config_param: 1640: set TXBF_SND_PERIOD: value 100 wmi_status 0 [ 96.793107] wlan: [0:I:ANY] ol_ath_set_config_param: 2392: Disconnect_timeout value: 10 [ 96.823828] wlan: [0:I:ANY] ol_ath_set_config_param: 2398: Reconfiguration_timeout value:60 number of vifs: vap1 vap3 vap5 vap7 [ 97.110488] wlan: [5246:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath1 : clone params: 0x00000001 [ 97.110557] wlan: [5246:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create 24:5e:be:52:: [ 97.121814] wlan: [5246:I:ANY] wlan_vap_create: 1599: devhandle=0xffffffc0326c0880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 97.121814] [ 97.130105] wlan: [5246:I:ANY] ol_ath_vap_set_param: 1208: Setting SGI value: 1 [ 97.142108] wlan: [5246:I:ANY] ol_ath_vap_set_param: 2240: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 97.149254] wlan: [5246:I:ANY] ol_ath_vap_set_param: 2253: he_bf_cap=0x7b [ 97.164640] wlan: [5246:I:ANY] ol_ath_vap_set_param: 2268: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 97.171263] wlan: [5246:I:ANY] MBO Initialized [ 97.185300] wlan: [5246:I:ANY] OCE Initialized [ 97.189616] wlan: [5246:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 44 nss_id -1 [ 97.194036] wlan: [5246:I:ANY] NSS radio_if 29 [ 97.203755] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0 [ 97.208052] wlan: [5246:I:ANY] osif_nss_ol_vap_create: 1393: vap create ffffffc0260a4880 : if_num 44 [ 97.216560] wlan: [5246:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 97.225663] wlan: [5246:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 97.234937] wlan: [5246:I:ANY] VAP device ath1 created osifp: (ffffffc0260a4880) os_if: (ffffffc01ba30000) [ 97.781613] wlan: [5329:I:ANY] wlan_set_param: 3031: HE MU BFER already set with this value =1 [ 97.892660] 8021q: adding VLAN 0 to HW filter on device ath1 [ 97.893904] device ath1 entered promiscuous mode [ 97.897634] br_v8: port 4(ath1) entered forwarding state [ 97.902021] br_v8: port 4(ath1) entered forwarding state [ 98.034722] wlan: [1184:I:ANY] DES SSID SET=C [ 98.034753] wlan: [1184:I:ANY] wlan_cfg80211_chan_to_phymode: 1239: wlan_cfg80211_chan_to_phymode: band:0 width: 2 channel_cfreq: 2457 center_freq1: 2447 chandef.center_freq2: 0 flags: 0 [ 98.079610] wlan: [5403:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath11 : clone params: 0x00000001 [ 98.079691] wlan: [5403:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create 2a:5e:be:52:: [ 98.093508] wlan: [5403:I:ANY] wlan_vap_create: 1599: devhandle=0xffffffc0326c0880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 98.093508] [ 98.101203] wlan: [5403:I:ANY] ol_ath_vap_set_param: 1208: Setting SGI value: 1 [ 98.111587] wlan: [5403:I:ANY] ol_ath_vap_set_param: 2240: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 98.118402] wlan: [5403:I:ANY] ol_ath_vap_set_param: 2253: he_bf_cap=0x7b [ 98.133760] wlan: [5403:I:ANY] ol_ath_vap_set_param: 2268: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 98.140506] wlan: [5403:I:ANY] MBO Initialized [ 98.153050] wlan: [0:I:CMN_MLME] vdev[4] ieee chan:10 freq:2457 [ 98.153218] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms. [ 98.153218] FD Interval should be a factor of BI. [ 98.153218] Disabling FD [ 98.153218] [ 98.153323] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms. [ 98.153323] FD Interval should be a factor of BI. [ 98.153323] Disabling FD [ 98.153323] [ 98.153358] wlan: [0:I:ANY] vdev[4]: Mgt Rate:1000(kbps) [ 98.153380] wlan: [0:I:ANY] vdev[4]: Mgt Rate:1000(kbps) [ 98.209945] wlan: [5403:I:ANY] OCE Initialized [ 98.215261] wlan: [5403:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 45 nss_id -1 [ 98.219496] wlan: [5403:I:ANY] NSS radio_if 29 [ 98.229230] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0 [ 98.233492] wlan: [5403:I:ANY] osif_nss_ol_vap_create: 1393: vap create ffffffc026f0e880 : if_num 45 [ 98.242000] wlan: [5403:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 98.251110] wlan: [5403:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 98.260340] wlan: [5403:I:ANY] VAP device ath11 created osifp: (ffffffc026f0e880) os_if: (ffffffc01bac0000) [ 98.835753] wlan: [5496:I:ANY] wlan_set_param: 3031: HE MU BFER already set with this value =1 [ 98.961113] 8021q: adding VLAN 0 to HW filter on device ath11 [ 98.962102] device ath11 entered promiscuous mode [ 98.966017] br_v7: port 3(ath11) entered forwarding state [ 98.970557] br_v7: port 3(ath11) entered forwarding state [ 99.094650] wlan: [1184:I:ANY] DES SSID SET=C [ 99.094681] wlan: [1184:I:ANY] wlan_cfg80211_chan_to_phymode: 1239: wlan_cfg80211_chan_to_phymode: band:0 width: 2 channel_cfreq: 2457 center_freq1: 2447 chandef.center_freq2: 0 flags: 0 [ 99.099708] wlan: [0:I:CMN_MLME] vdev[5] ieee chan:10 freq:2457 [ 99.115564] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms. [ 99.115564] FD Interval should be a factor of BI. [ 99.115564] Disabling FD [ 99.115564] [ 99.121374] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms. [ 99.121374] FD Interval should be a factor of BI. [ 99.121374] Disabling FD [ 99.121374] [ 99.141537] wlan: [0:I:ANY] vdev[5]: Mgt Rate:1000(kbps) [ 99.161365] wlan: [0:I:ANY] vdev[5]: Mgt Rate:1000(kbps) [ 99.182833] wlan: [5577:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath12 : clone params: 0x00000001 [ 99.182988] wlan: [5577:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create 2e:5e:be:52:: [ 99.194318] wlan: [5577:I:ANY] wlan_vap_create: 1599: devhandle=0xffffffc0326c0880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 99.194318] [ 99.202690] wlan: [5577:I:ANY] ol_ath_vap_set_param: 1208: Setting SGI value: 1 [ 99.214965] wlan: [5577:I:ANY] ol_ath_vap_set_param: 2240: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 99.221878] wlan: [5577:I:ANY] ol_ath_vap_set_param: 2253: he_bf_cap=0x7b [ 99.237502] wlan: [5577:I:ANY] ol_ath_vap_set_param: 2268: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 99.243968] wlan: [5577:I:ANY] MBO Initialized [ 99.258052] wlan: [5577:I:ANY] OCE Initialized [ 99.262302] wlan: [5577:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 46 nss_id -1 [ 99.266760] wlan: [5577:I:ANY] NSS radio_if 29 [ 99.276503] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0 [ 99.280677] wlan: [5577:I:ANY] osif_nss_ol_vap_create: 1393: vap create ffffffc033df0880 : if_num 46 [ 99.289536] wlan: [5577:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 99.298414] wlan: [5577:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 99.307444] wlan: [5577:I:ANY] VAP device ath12 created osifp: (ffffffc033df0880) os_if: (ffffffc01b988000) [ 99.835069] wlan: [5668:I:ANY] wlan_set_param: 3031: HE MU BFER already set with this value =1 [ 99.946693] 8021q: adding VLAN 0 to HW filter on device ath12 [ 99.947627] device ath12 entered promiscuous mode [ 99.951900] br_v8: port 5(ath12) entered forwarding state [ 99.956193] br_v8: port 5(ath12) entered forwarding state [ 100.074706] wlan: [1184:I:ANY] DES SSID SET=C [ 100.074738] wlan: [1184:I:ANY] wlan_cfg80211_chan_to_phymode: 1239: wlan_cfg80211_chan_to_phymode: band:0 width: 2 channel_cfreq: 2457 center_freq1: 2447 chandef.center_freq2: 0 flags: 0 [ 100.081029] wlan: [0:I:CMN_MLME] vdev[6] ieee chan:10 freq:2457 [ 100.095656] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms. [ 100.095656] FD Interval should be a factor of BI. [ 100.095656] Disabling FD [ 100.095656] [ 100.101491] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms. [ 100.101491] FD Interval should be a factor of BI. [ 100.101491] Disabling FD [ 100.101491] [ 100.121575] wlan: [0:I:ANY] vdev[6]: Mgt Rate:1000(kbps) [ 100.135252] wlan: [5753:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: gt1 : clone params: 0x00000001 [ 100.135285] wlan: [5753:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create 32:5e:be:52:: [ 100.135327] wlan: [5753:I:ANY] wlan_vap_create: 1599: devhandle=0xffffffc0326c0880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 100.135327] [ 100.166755] wlan: [0:I:ANY] vdev[6]: Mgt Rate:1000(kbps) [ 100.180051] wlan: [5753:I:ANY] ol_ath_vap_set_param: 1208: Setting SGI value: 1 [ 100.185153] wlan: [5753:I:ANY] ol_ath_vap_set_param: 2240: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 100.191425] wlan: [5753:I:ANY] ol_ath_vap_set_param: 2253: he_bf_cap=0x7b [ 100.207150] wlan: [5753:I:ANY] ol_ath_vap_set_param: 2268: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 100.213525] wlan: [5753:I:ANY] MBO Initialized [ 100.228073] wlan: [5753:I:ANY] OCE Initialized [ 100.231879] wlan: [5753:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 47 nss_id -1 [ 100.236660] wlan: [5753:I:ANY] NSS radio_if 29 [ 100.246041] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0 [ 100.250284] wlan: [5753:I:ANY] osif_nss_ol_vap_create: 1393: vap create ffffffc0326fc880 : if_num 47 [ 100.258791] wlan: [5753:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 100.267911] wlan: [5753:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 100.277251] wlan: [5753:I:ANY] VAP device gt1 created osifp: (ffffffc0326fc880) os_if: (ffffffc01b090000) [ 100.791346] wlan: [5853:I:ANY] wlan_set_param: 3031: HE MU BFER already set with this value =1
OpenWrt bootlog
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.75 (dirk@nitropc) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r17769+169-333f93333e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Fri Oct 29 18:36:13 2021 [ 0.000000] Machine model: QNAP 301w [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff] [ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff] [ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff] [ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 4096 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 262144 pages, LIFO batch:63 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s41112 r8192 d32616 u81920 [ 0.000000] pcpu-alloc: s41112 r8192 d32616 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 root=PARTUUID=2a213133-47f8-80a1-5d66-1d565a2ec756 rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 888836K/1048576K available (7166K kernel code, 844K rwdata, 1844K rodata, 1152K init, 302K bss, 159740K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] random: get_random_bytes called from start_kernel+0x350/0x558 with crng_init=0 [ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000173] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.000189] pid_max: default: 32768 minimum: 301 [ 0.000316] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.000329] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.001729] rcu: Hierarchical SRCU implementation. [ 0.001873] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.002364] smp: Bringing up secondary CPUs ... [ 0.002902] Detected VIPT I-cache on CPU1 [ 0.002969] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.003536] Detected VIPT I-cache on CPU2 [ 0.003577] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.004191] Detected VIPT I-cache on CPU3 [ 0.004229] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.004302] smp: Brought up 1 node, 4 CPUs [ 0.004315] SMP: Total of 4 processors activated. [ 0.004324] CPU features: detected: 32-bit EL0 Support [ 0.004332] CPU features: detected: CRC32 instructions [ 0.004384] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.004393] CPU: All CPU(s) started at EL1 [ 0.004414] alternatives: patching kernel code [ 0.012529] KASLR disabled due to lack of seed [ 0.012668] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.012687] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.012823] pinctrl core: initialized pinctrl subsystem [ 0.013846] NET: Registered protocol family 16 [ 0.014325] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.014364] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.014400] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.014983] thermal_sys: Registered thermal governor 'step_wise' [ 0.016730] cpuidle: using governor ladder [ 0.016942] NET: Registered protocol family 42 [ 0.017095] ASID allocator initialised with 65536 entries [ 0.088301] usbcore: registered new interface driver usbfs [ 0.088357] usbcore: registered new interface driver hub [ 0.088412] usbcore: registered new device driver usb [ 0.088675] qcom_scm: convention: smc arm 64 [ 0.090018] clocksource: Switched to clocksource arch_sys_counter [ 0.090919] NET: Registered protocol family 2 [ 0.091046] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.091787] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.091816] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.091903] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.092051] TCP: Hash tables configured (established 8192 bind 8192) [ 0.092147] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.092236] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.092413] NET: Registered protocol family 1 [ 0.092445] PCI: CLS 0 bytes, default 64 [ 0.093910] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.097594] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.097609] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.098998] qcom-qmp-phy 58000.phy: supply vdda-phy not found, using dummy regulator [ 0.099146] qcom-qmp-phy 58000.phy: supply vdda-pll not found, using dummy regulator [ 0.100113] qcom-qmp-phy 58000.phy: Registered Qcom-QMP phy [ 0.100369] qcom-qmp-phy 78000.phy: supply vdda-phy not found, using dummy regulator [ 0.100486] qcom-qmp-phy 78000.phy: supply vdda-pll not found, using dummy regulator [ 0.101338] qcom-qmp-phy 78000.phy: Registered Qcom-QMP phy [ 0.101985] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator [ 0.102177] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator [ 0.102330] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy [ 0.102512] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator [ 0.102620] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator [ 0.102760] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy [ 0.104000] bam-dma-engine 704000.dma: num-channels unspecified in dt [ 0.104015] bam-dma-engine 704000.dma: num-ees unspecified in dt [ 0.108881] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.109469] msm_serial 78b3000.serial: msm_serial: detected port #0 [ 0.109506] msm_serial 78b3000.serial: uartclk = 3686400 [ 0.109559] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 24, base_baud = 230400) is a MSM [ 0.109586] msm_serial: console setup on port #0 [ 0.777000] printk: console [ttyMSM0] enabled [ 0.782160] msm_serial: driver initialized [ 0.790103] loop: module loaded [ 0.790981] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 0.793838] spi-nor spi0.0: found w25q64dw, expected n25q128a11 [ 0.800518] spi-nor spi0.0: w25q64dw (8192 Kbytes) [ 0.806313] 12 qcomsmem partitions found on MTD device spi0.0 [ 0.810761] Creating 12 MTD partitions on “spi0.0”: [ 0.816577] 0x000000000000-0x000000050000 : “0:sbl1” [ 0.821694] 0x000000050000-0x000000060000 : “0:mibib” [ 0.826824] 0x000000060000-0x0000001e0000 : “0:qsee” [ 0.831779] 0x0000001e0000-0x0000001f0000 : “0:devcfg” [ 0.836804] 0x0000001f0000-0x000000200000 : “0:apdp” [ 0.841749] 0x000000200000-0x000000240000 : “0:rpm” [ 0.846873] 0x000000240000-0x000000250000 : “0:cdt” [ 0.851511] 0x000000250000-0x000000270000 : “0:appsblenv” [ 0.856344] 0x000000270000-0x000000370000 : “0:appsbl” [ 0.861904] 0x000000370000-0x0000003b0000 : “0:art” [ 0.866926] 0x0000003b0000-0x000000430000 : “0:ethphyfw” [ 0.871707] 0x000000430000-0x000000800000 : “reserved” [ 0.881264] spmi spmi-0: PMIC arbiter version v2 (0x20010000) [ 0.882797] pmd9655_s3: supplied by e-smps1-reg [ 0.888002] pmd9655_s4: supplied by e-smps1-reg [ 0.892389] pmd9655_ldo11: supplied by e-smps1-reg [ 0.897698] libphy: Fixed MDIO Bus: probed [ 0.902030] libphy: ipq4019_mdio: probed [ 0.911853] i2c /dev entries driver [ 0.916252] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz [ 0.917176] sdhci: Secure Digital Host Controller Interface driver [ 0.925876] sdhci: Copyright© Pierre Ossman [ 0.932001] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.938995] remoteproc remoteproc0: cd00000.q6v5_wcss is available [ 0.942957] NET: Registered protocol family 10 [ 0.948755] Segment Routing with IPv6 [ 0.952615] NET: Registered protocol family 17 [ 0.956361] Bridge firewalling registered [ 0.960649] 8021q: 802.1Q VLAN Support v1.8 [ 0.973336] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit [ 0.974154] Waiting for root device PARTUUID=2a213133-47f8-80a1-5d66-1d565a2ec756... [ 1.027448] mmc0: new high speed MMC card at address 0001 [ 1.027961] mmcblk0: mmc0:0001 Q2J54A 3.64 GiB [ 1.032000] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 2.00 MiB [ 1.036337] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 2.00 MiB [ 1.042128] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB, chardev (249:0) [ 1.050102] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 [ 1.073316] VFS: Mounted root (squashfs filesystem) readonly on device 179:4. [ 1.073709] Freeing unused kernel memory: 1152K [ 1.106190] Run /sbin/init as init process [ 1.106213] with arguments: [ 1.106216] /sbin/init [ 1.106219] with environment: [ 1.106222] HOME=/ [ 1.106225] TERM=linux [ 1.233909] init: Console is alive [ 1.234060] init: - watchdog - [ 1.778882] random: fast init done [ 1.836093] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 1.858971] raid6: skip pq benchmark and using algorithm neonx8 [ 1.859002] raid6: using neon recovery algorithm [ 1.864385] xor: measuring software checksum speed [ 1.871279] 8regs : 3630 MB/sec [ 1.875443] 32regs : 4299 MB/sec [ 1.880284] arm64_neon : 3650 MB/sec [ 1.881920] xor: using function: 32regs (4299 MB/sec) [ 1.969455] Btrfs loaded, crc32c=crc32c-generic [ 1.978742] genirq: irq_chip msmgpio did not update eff. affinity mask of irq 107 [ 1.981466] SCSI subsystem initialized [ 1.988416] dwc3-qcom 8af8800.usb: IRQ hs_phy_irq not found [ 1.988846] dwc3-qcom 8af8800.usb: IRQ dp_hs_phy_irq not found [ 1.994333] dwc3-qcom 8af8800.usb: IRQ dm_hs_phy_irq not found [ 2.000222] dwc3-qcom 8af8800.usb: IRQ ss_phy_irq not found [ 2.007886] dwc3-qcom 8cf8800.usb: IRQ hs_phy_irq not found [ 2.011515] dwc3-qcom 8cf8800.usb: IRQ dp_hs_phy_irq not found [ 2.017069] dwc3-qcom 8cf8800.usb: IRQ dm_hs_phy_irq not found [ 2.022964] dwc3-qcom 8cf8800.usb: IRQ ss_phy_irq not found [ 2.036127] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.036168] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 2.040649] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000002010010 [ 2.048100] xhci-hcd xhci-hcd.1.auto: irq 109, io mem 0x08a00000 [ 2.057529] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.063686] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 2.068985] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 2.076895] hub 1-0:1.0: USB hub found [ 2.083178] hub 1-0:1.0: 1 port detected [ 2.087170] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.091304] hub 2-0:1.0: USB hub found [ 2.099032] hub 2-0:1.0: 1 port detected [ 2.102919] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 2.106670] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 2.112082] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000002010010 [ 2.119547] xhci-hcd xhci-hcd.2.auto: irq 110, io mem 0x08c00000 [ 2.128975] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 2.135131] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 2.140431] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 2.148284] hub 3-0:1.0: USB hub found [ 2.154585] hub 3-0:1.0: 1 port detected [ 2.158473] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.162583] hub 4-0:1.0: USB hub found [ 2.170468] hub 4-0:1.0: 1 port detected [ 2.177362] usbcore: registered new interface driver usb-storage [ 2.178891] usbcore: registered new interface driver uas [ 2.184303] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.197182] init: - preinit - [ 2.427206] random: jshn: uninitialized urandom read (4 bytes read) [ 2.441687] random: jshn: uninitialized urandom read (4 bytes read) [ 2.454421] random: jshn: uninitialized urandom read (4 bytes read) [ 6.713457] EXT4-fs (loop0): recovery complete [ 6.717129] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 6.721167] mount_root: switching to ext4 overlay [ 6.726304] overlayfs: “xino” feature enabled using 32 upper inode bits. [ 6.731577] urandom-seed: Seeding with /etc/urandom.seed [ 7.473106] procd: - early - [ 7.473187] procd: - watchdog - [ 8.028946] procd: - watchdog - [ 8.029991] procd: - ubus - [ 8.051379] urandom_read: 3 callbacks suppressed [ 8.051385] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.082026] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.082247] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.090935] procd: - init - [ 8.259416] urngd: v1.0.2 started. [ 8.273542] random: crng init done [ 8.273570] random: 1 urandom warning(s) missed due to ratelimiting [ 8.286298] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.330352] RPC: Registered named UNIX socket transport module. [ 8.330383] RPC: Registered udp transport module. [ 8.335083] RPC: Registered tcp transport module. [ 8.339960] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.429233] ssdk_switch_device_num_init[1160]:INFO:ess-switch dts node number: 1 [ 8.429313] ssdk_dt_get_switch_node[971]:INFO:ess-switch DT exist! [ 8.435706] ssdk_dt_parse_access_mode[857]:INFO:switch_access_mode: local bus [ 8.441686] ssdk_dt_parse_access_mode[870]:INFO:switchreg_base_addr: 0x3a000000 [ 8.448896] ssdk_dt_parse_access_mode[871]:INFO:switchreg_size: 0x1000000 [ 8.456011] ssdk_dt_parse_mac_mode[295]:INFO:mac mode = 0x0 [ 8.462951] ssdk_dt_parse_mac_mode[304]:INFO:mac mode1 = 0xd [ 8.468333] ssdk_dt_parse_mac_mode[313]:INFO:mac mode2 = 0xd [ 8.474294] ssdk_dt_parse_uniphy[332]:INFO:ess-uniphy DT exist! [ 8.480008] ssdk_dt_parse_intf_mac[800]:INFO:dp1 MAC 24:5e:be:52:e4:0b [ 8.485569] ssdk_dt_parse_intf_mac[800]:INFO:dp2 MAC 24:5e:be:52:e4:0c [ 8.492162] ssdk_dt_parse_intf_mac[800]:INFO:dp3 MAC 24:5e:be:52:e4:0d [ 8.498672] ssdk_dt_parse_intf_mac[800]:INFO:dp4 MAC 24:5e:be:52:e4:0e [ 8.505182] ssdk_dt_parse_intf_mac[800]:INFO:dp5 MAC 24:5e:be:52:e4:0f [ 8.511693] ssdk_dt_parse_intf_mac[800]:INFO:dp6 MAC 24:5e:be:52:e4:10 [ 8.518171] ssdk_plat_init start [ 8.575541] ssdk_gcc_clock_init[1033]:INFO:SSDK gcc clock init successfully! [ 8.576558] HPPE initializing... [ 8.582110] ssdk_phy_driver_init[327]:INFO:dev_id = 0, phy_adress = 6, phy_id = 0xffffffff phytype doesn't match [ 8.584872] malibu_phy_api_ops_init[2848]:INFO:qca probe malibu phy driver succeeded! [ 8.599221] aquantia_phy_api_ops_init[2180]:INFO:qca probe aquantia phy driver succeeded! [ 8.603895] regi_init[3567]:INFO:Initializing HPPE!! [ 8.830021] ssdk_ppe_reset_init[1265]:INFO:ppe reset successfully! [ 8.833259] qca_hppe_tdm_hw_init[684]:INFO:tdm setup num=96 [ 8.835413] qca_hppe_portctrl_hw_init[110]:INFO:Hawkeye PPE port initializing [ 12.202051] ssdk_switch_register[1718]:INFO:Chip version 0x1500 [ 12.202093] qca_link_polling_select[1315]:INFO:link-polling-required node does not exist [ 12.206787] ssdk_switch_register[1744]:INFO:polling is selected [ 12.215113] regi_init[3571]:INFO:Initializing HPPE Done!! [ 12.220809] regi_init[3631]:INFO:qca-ssdk module init succeeded! [ 12.232550] EDMA ver 1 hw init [ 12.232798] EDMA HW Reset completed succesfully [ 12.235288] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7) [ 12.239673] RxDesc:1 (15-15) RxFill:1 (7-7) [ 12.248954] Aquantia AQR113C 90000.mdio-1:08: FW 5.4, Build 4, Provisioning 1 [ 12.250306] Aquantia AQR113C 90000.mdio-1:00: FW 5.4, Build 4, Provisioning 1 [ 12.257407] [ 12.263495] * NSS Data Plane driver [ 12.269941] [ 12.358220] nss_driver - fw of size 833304 bytes copied to load addr: 40000000, nss_id : 0 [ 12.360056] Supported Frequencies - [ 12.360063] 187.2 MHz [ 12.365454] 748.8 MHz [ 12.369203] 1.4976 GHz
[ 12.376137] ffffffc008bd5900: set sdma ffffff8004346800 [ 12.377862] ffffffc008bd5900: meminfo init succeed [ 12.417451] nss_driver - fw of size 292296 bytes copied to load addr: 40800000, nss_id : 1 [ 12.418032] node size 2 # items 4 [ 12.418195] Supported Frequencies - [ 12.424604] memory: 40000000 1073741824 (avl 930783232) items 4 active_cores 2 [ 12.424604] 187.2 MHz [ 12.424607] 748.8 MHz [ 12.428087] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 [ 12.431728] 1.4976 GHz [ 12.438752] ffffffc008bd5900: nss core 0 booted successfully
[ 12.458623] ffffffc008bdd140: set sdma ffffff8004bc7400 [ 12.460073] ffffffc008bdd140: meminfo init succeed [ 12.465111] debugfs: Directory 'dynamic_if' with parent 'stats' already present! [ 12.469849] debugfs: File 'n2h' in directory 'strings' already present! [ 12.477388] debugfs: File 'drv' in directory 'strings' already present! [ 12.487741] node size 2 # items 4 [ 12.490402] memory: 40000000 1073741824 (avl 930783232) items 4 active_cores 2 [ 12.493817] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 [ 12.500939] ffffffc008bdd140: nss core 1 booted successfully [ 12.501371] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 12.521625] PPP generic driver version 2.4.2 [ 12.522409] NET: Registered protocol family 24 [ 12.528696] fuse: init (API version 7.32) [ 12.531984] Loading modules backported from Linux version v5.15-rc6-0-g519d81956ee2 [ 12.533319] Backport generated by backports.git v5.15-rc6-1-0-gd44432d6 [ 12.555535] xt_time: kernel timezone is -0000 [ 12.598302] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 12.598335] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved. [ 12.616066] ath11k c000000.wifi: ipq8074 hw2.0 [ 12.616265] remoteproc remoteproc0: powering up cd00000.q6v5_wcss [ 12.629145] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 13.491522] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up [ 13.494168] ath11k c000000.wifi: qmi ignore invalid mem req type 3 [ 13.498574] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff [ 13.498719] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.503995] ath11k c000000.wifi: fw_version 0x250684a5 fw_build_timestamp 2021-07-13 10:57 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 [ 14.416056] ECM init [ 14.416115] ECM database jhash random seed: 0x77f37101 [ 14.418234] ECM init complete [ 15.075845] br-lan: port 1(eth0) entered blocking state [ 15.075878] br-lan: port 1(eth0) entered disabled state [ 15.080249] device eth0 entered promiscuous mode [ 15.090892] br-lan: port 2(eth1) entered blocking state [ 15.090924] br-lan: port 2(eth1) entered disabled state [ 15.095314] device eth1 entered promiscuous mode [ 15.103270] br-lan: port 3(eth2) entered blocking state [ 15.104997] br-lan: port 3(eth2) entered disabled state [ 15.110418] device eth2 entered promiscuous mode [ 15.117555] nss-dp 3a001600.dp4 eth3: PHY Link up speed: 1000 [ 15.120700] br-lan: port 4(eth3) entered blocking state [ 15.125767] br-lan: port 4(eth3) entered disabled state [ 15.131025] device eth3 entered promiscuous mode [ 15.138930] br-lan: port 5(eth4) entered blocking state [ 15.140757] br-lan: port 5(eth4) entered disabled state [ 15.145967] device eth4 entered promiscuous mode [ 16.094102] br-lan: port 4(eth3) entered blocking state [ 16.094138] br-lan: port 4(eth3) entered forwarding state [ 16.098657] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 105.883075] br-lan: port 6(wlan1) entered blocking state [ 105.883109] br-lan: port 6(wlan1) entered disabled state [ 105.887792] device wlan1 entered promiscuous mode [ 105.892915] br-lan: port 6(wlan1) entered blocking state [ 105.897410] br-lan: port 6(wlan1) entered forwarding state [ 105.903311] br-lan: port 6(wlan1) entered disabled state [ 106.073859] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 106.074098] br-lan: port 6(wlan1) entered blocking state [ 106.079312] br-lan: port 6(wlan1) entered forwarding state [ 107.619024] wlan0: authenticate with 00:03:7f:12:99:43 [ 107.931150] wlan0: send auth to 00:03:7f:12:99:43 (try 1/3) [ 107.949286] wlan0: authenticate with 00:03:7f:12:99:43 [ 107.949321] wlan0: send auth to 00:03:7f:12:99:43 (try 1/3) [ 107.955067] wlan0: authenticated [ 107.962062] wlan0: associate with 00:03:7f:12:99:43 (try 1/3) [ 107.965767] wlan0: RX AssocResp from 00:03:7f:12:99:43 (capab=0x11 status=0 aid=3) [ 107.970406] wlan0: associated [ 108.354314] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 244.478730] nss-dp 3a001600.dp4 eth3: PHY Link is down [ 244.479030] br-lan: port 4(eth3) entered disabled state