User Tools

Site Tools


toh:powercloud_systems:powercloud_systems_cr5000

PowerCloud Systems CR5000

Originally a cloud managed router the CR5000 (aka Skydog) is now only usable with OpenWrt (since the cloud service has gone away). It's a basic AR934x gigabit 5-port switch (no separate WAN) with dual band wifi and a USB 2.0 port.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
CR5000Atheros AR1022535864Atheros AR1022, Atheros AR9382b/g/na/n-5-1x 2.0

Installation

OEM installation using the TFTP method (via ramdisk)

generic.flashing.tftp

installation

One boots a ramdisk image and then does a normal OpenWrt sysupgrade (generic.sysupgrade)

Specific values needed for tftp

If one holds the WPS button and then (with button pressed) powers on the device (holding WPS button for 5-7 seconds) the device will attempt to download a ramdisk image named ap.bin from a tftp server (but only using the WAN port) at 192.168.1.10. Note that for 17.xx or 18.xx using the snapshot below will require the use of sysupgrade -F. Also note that some devices will attempt to load from 192.168.1.17 and that if the u-boot environment has been corrupted the ramdisk image will need to be named vmlinux.uImage.

Bootloader tftp client IPv4 address 192.168.1.1 on the WAN port
Firmware tftp image Ramdisk from 'snapshots' (NOTE: Must renamed as ap.bin (or, if u-boot environment is corrupt, vmlinux.uImage))
TFTP window start approximately 5-7 seconds after power on
TFTP server required IP address 192.168.1.10 (on some devices 192.168.1.17)

OEM installation using the Serial method

→ Flashing from stock firmware requires Generic Flashing over the Serial Port

The correct commands for this device are:

setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.234
tftpboot 0x80060000 firm.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
bootm 0x9f050000

Flash Layout

Current Snapshots or 'no-cloud' images for 17.xx/18.xx

Layer0 raw flash, 8192 KiB
Layer1 mtd0
u-boot
256 KiB
mtd1
u-boot-env
64 KiB
mtd2
firmware
7872 KiB (= FlashSize-(256+64+64))
mtd6
art 64 KiB
Layer2 mtd3
kernel
about 1 MiB
mtd4
rootfs
Layer3 /dev/root
around 2 MiB
mtd5
rootfs_data
around 4.5 MiB

OEM or regular (not no-cloud) images for 17.xx/18.xx

Layer0 raw flash, 8192 KiB
Layer1 mtd0
u-boot
256 KiB
mtd1
u-boot-env
64 KiB
mtd2
firmware
7232 KiB (= FlashSize-(256+64+640+64))
mtd6
certs 640 KiB
mtd7
art 64 KiB
Layer2 mtd3
kernel
about 1 MiB
mtd4
rootfs
Layer3 /dev/root
around 2 MiB
mtd5
rootfs_data
around 4.5 MiB

OEM easy installation

There is no 'easy installation' from the OEM firmware for this device. TFTP (either a TFTP server to load a ramdisk and do sysupgrade, or adding a serial port and using TFTP from U-Boot) is required.

Upgrading OpenWrt

Debricking

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan Lan & WiFi 192.168.1.1/24
vlan1 (eth0.1) Parent of br-lan see br-lan
vlan2 (eth0.2) WAN port DHCP
wlan0 2.4 GHz WiFi Disabled
wlan1 5 GHz WiFi Disabled

Switch Ports (for VLANs)

Numbers 1-5 are Ports 1-5 as labeled on the unit, number 5 is the Internet (WAN) on the unit, 0 is the internal connection to the router itself.

Port Switch port
Internet (WAN) 5
LAN 1 1
LAN 2 2
LAN 3 3
LAN 4 4

Buttons

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The PowerCloud Systems CR5000 has the following buttons:

BUTTON Event
Reset reset
WiFi Protected Setup wps

Hardware

Info

General
Brand PowerCloud Systems
Model CR5000
Versions
Device Type WiFi Router
Availability Discontinued
Comments - general aka "Senao WBR4200AGN", aka"Skydog", serial header is not populated
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fb1273dfddd89ff487dae16265a2870e9d175dfb
Supported Since Release 17.01.0
Supported Current Release 18.06.5
Unsupported
Hardware
Instruction set
Sub Instruction Set
Bootloader U-Boot
Target ar71xx-ath79
System-On-Chip
CPU MHz 535
Flash MB 8
RAM MB 64
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
Switch Atheros AR8327
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n
WLAN Hardware Atheros AR1022, Atheros AR9382
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports 1x 2.0
SATA ports -
Serial Yes
JTAG No
Comments - USB & SATA ports
Misc
LED count 3
Button count 2
Power supply 12 VDC, 1.25 A
Links
Forum Topic URL
WikiDevi URL https://wikidevi.com/wiki/Senao_WBR4200AGN
OEM device homepage URL http://skydog.com/
Firmware OEM Stock URL
Firmware OpenWrt Install URL http://downloads.openwrt.org/releases/18.06.5/targets/ar71xx/generic/openwrt-18.06.5-ar71xx-generic-cr5000-nocloud-squashfs-sysupgrade.bin
Firmware OpenWrt Upgrade URL http://downloads.openwrt.org/releases/18.06.5/targets/ar71xx/generic/openwrt-18.06.5-ar71xx-generic-cr5000-nocloud-squashfs-sysupgrade.bin
Edit the underlying data View/Edit data

Photos

Front:

Back:

Bottom label:

Opening the case

Note: This will void your warranty!

  1. Remove four (4) rubber feet on bottom of device.
  2. Remove four (4) screws in the recesses that were covered by the feet.
  3. Separate top and bottom (the top should just lift off).

Main PCB:

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Need to solder on a header. (see below)

Pin 1 is marked with an arrow and is partly covered by the wireless antenna pigtail above.

Pin 4 3 2 1
Signal RX TX GND VCC

Vcc is 3.3V NOT 5V (so a PL2023 or FTDI 3.3V cable is appropriate).

Serial connection parameters
for PowerCloud Systems CR5000
115200, 8N1

Bootloader mods

Hardware mods

None so far.

Bootlogs

OEM bootlog

U-Boot 1.1.4 (Mar 4 2013 - 19:23:50) U-boot MI124 DRAM: sri Wasp 1.1 wasp_ddr_initial_config(255): (16bit) ddr2 init 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 251k for U-Boot at: 83fc0000 Reserving 192k for malloc() at: 83f90000 Reserving 44 Bytes for Board Info at: 83f8ffd4 Reserving 36 Bytes for Global Data at: 83f8ffb0 Reserving 128k for boot params() at: 83f6ffb0 Stack Pointer at: 83f6ff98 Now running in RAM - U-Boot at: 83fc0000 id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MB pcie module ID is correct 0x30168c BOARD IS NOT CALIBRATED!!! In: serial Out: serial Err: serial Net: ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0x7 cfg2 0x7114 eth0: 00:03:7f:09:0b:ad athrs17_reg_init: complete eth0 up eth0 Hit any key to stop autoboot: 6 ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0xf cfg2 0x7114 eth0: 00:03:7f:09:0b:ad eth0 up eth0 ## Booting image at 9f050000 ... Image Name: MIPS OpenWrt Linux-3.3.8 Created: 2014-01-15 9:30:13 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1022128 Bytes = 998.2 kB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum at 0x9f050040 ...OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... [ 0.000000] Linux version 3.3.8 (enable@enable-buildsvr2) (collect2: ld returned 1 exit status) #1 Tue Jan 14 20:12:51 PST 2014 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9342 rev 1 [ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=CR5000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),5696k(rootfs),640k(certs),64k(nvram),64k(art)ro,7104k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61372k/65536k available (2176k kernel code, 4164k reserved, 572k data, 212k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79 [ 0.100000] MIPS: machine is CR5000 Cloud Router [ 0.100000] registering PCI controller with io_map_base unset [ 0.310000] bio: create slab <bio-0> at 0 [ 0.320000] PCI host bridge to bus 0000:00 [ 0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.330000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.330000] pci 0000:00:00.0: invalid calibration data [ 0.340000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 0.350000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.350000] Switching to clocksource MIPS [ 0.360000] NET: Registered protocol family 2 [ 0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.360000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.370000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.370000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.380000] TCP reno registered [ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.390000] NET: Registered protocol family 1 [ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.430000] msgmni has been set to 119 [ 0.430000] io scheduler noop registered [ 0.440000] io scheduler deadline registered (default) [ 0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.470000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.480000] console [ttyS0] enabled, bootconsole disabled [ 0.480000] console [ttyS0] enabled, bootconsole disabled [ 0.490000] m25p80 spi0.0: found mx25l6405d, expected m25p80 [ 0.500000] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 0.500000] 8 cmdlinepart partitions found on MTD device spi0.0 [ 0.510000] Creating 8 MTD partitions on "spi0.0": [ 0.510000] 0x000000000000-0x000000040000 : "u-boot" [ 0.520000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.530000] 0x000000050000-0x0000001b0000 : "kernel" [ 0.530000] 0x0000001b0000-0x000000740000 : "rootfs" [ 0.540000] mtd: partition "rootfs" set to be root filesystem [ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=5F0000, len=150000 [ 0.560000] 0x0000005f0000-0x000000740000 : "rootfs_data" [ 0.560000] 0x000000740000-0x0000007e0000 : "certs" [ 0.570000] 0x0000007e0000-0x0000007f0000 : "nvram" [ 0.580000] 0x0000007f0000-0x000000800000 : "art" [ 0.580000] 0x000000050000-0x000000740000 : "firmware" [ 0.610000] ag71xx_mdio: probed [ 0.740000] ag71xx_mdio: probed [ 0.750000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.320000] eth0: Atheros AR8327 switch driver attached. [ 2.480000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 2.500000] ag71xx_hw_probe: clear tx clock delay [ 2.500000] ag71xx_hw_probe: clear rx clock delay [ 2.510000] TCP cubic registered [ 2.510000] NET: Registered protocol family 17 [ 2.510000] Bridge firewalling registered [ 2.520000] 8021q: 802.1Q VLAN Support v1.8 [ 2.530000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.540000] Freeing unused kernel memory: 212k freed - preinit - - regular preinit - [ 4.750000] JFFS2 notice: (468) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 0 orphan) and 3 of xref (0 dead, 0 orphan) found. switching to jffs2 - init - Please press Enter to activate this console. [ 6.140000] Compat-drivers backport release: compat-drivers-2013-01-21-1 [ 6.140000] Backport based on wireless-testing.git master-2013-02-22 [ 6.150000] compat.git: wireless-testing.git [ 6.300000] cfg80211: Calling CRDA to update world regulatory domain [ 6.300000] cfg80211: World regulatory domain updated: [ 6.310000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 6.320000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.330000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.330000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.340000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.350000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.680000] usbcore: registered new interface driver usbfs [ 6.690000] usbcore: registered new interface driver hub [ 6.700000] usbcore: registered new device driver usb [ 7.290000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47 [ 7.290000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 7.410000] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=40 [ 7.420000] cfg80211: Calling CRDA for country: US [ 7.420000] cfg80211: Regulatory domain changed to country: US [ 7.430000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 7.440000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.440000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.450000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.460000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.470000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.480000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.630000] PPP generic driver version 2.4.2 [ 7.660000] tun: Universal TUN/TAP device driver, 1.6 [ 7.670000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 7.690000] PPP MPPE Compression module registered [ 7.790000] GRE over IPv4 demultiplexor driver [ 7.810000] GRE over IPv4 tunneling driver [ 8.040000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.260000] NET: Registered protocol family 24 [ 8.360000] nf_conntrack version 0.5.0 (962 buckets, 3848 max) [ 8.750000] PPTP driver version 0.8.5 [ 9.410000] xt_time: kernel timezone is -0000 [ 9.890000] Netfilter messages via NETLINK v0.30. [ 10.070000] Ebtables v2.0 registered [ 10.330000] ip_set: protocol 6 [ 10.840000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 14.700000] device eth0.3 entered promiscuous mode [ 14.710000] device eth0 entered promiscuous mode [ 16.040000] eth0: link up (1000Mbps/Full duplex) [ 16.060000] br-setup: port 1(eth0.3) entered forwarding state [ 16.060000] br-setup: port 1(eth0.3) entered forwarding state [ 18.060000] br-setup: port 1(eth0.3) entered forwarding state [ 21.100000] device wlan0 entered promiscuous mode [ 21.140000] br-setup: port 2(wlan0) entered forwarding state [ 21.140000] br-setup: port 2(wlan0) entered forwarding state [ 23.140000] br-setup: port 2(wlan0) entered forwarding state [ 25.390000] device wlan1 entered promiscuous mode [ 25.410000] br-setup: port 3(wlan1) entered forwarding state [ 25.420000] br-setup: port 3(wlan1) entered forwarding state [ 27.420000] br-setup: port 3(wlan1) entered forwarding state


OEM factory reset log

[ 34.080000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 34.100000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 34.100000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 42.750000] JFFS2 notice: (1657) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 42.770000] Removing MTD device #4 (rootfs_data) with use count 1 [ 42.790000] Restarting system. U-Boot 1.1.4 (Mar 4 2013 - 19:23:50) U-boot MI124 DRAM: sri Wasp 1.1 wasp_ddr_initial_config(255): (16bit) ddr2 init 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 251k for U-Boot at: 83fc0000 Reserving 192k for malloc() at: 83f90000 Reserving 44 Bytes for Board Info at: 83f8ffd4 Reserving 36 Bytes for Global Data at: 83f8ffb0 Reserving 128k for boot params() at: 83f6ffb0 Stack Pointer at: 83f6ff98 Now running in RAM - U-Boot at: 83fc0000 id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MB pcie module ID is correct 0x30168c BOARD IS NOT CALIBRATED!!! In: serial Out: serial Err: serial Net: ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0x7 cfg2 0x7114 eth0: 00:03:7f:09:0b:ad athrs17_reg_init: complete eth0 up eth0 Hit any key to stop autoboot: 6 ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0xf cfg2 0x7114 eth0: 00:03:7f:09:0b:ad eth0 up eth0 ## Booting image at 9f050000 ... Image Name: MIPS OpenWrt Linux-3.3.8 Created: 2014-01-15 9:30:13 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1022128 Bytes = 998.2 kB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum at 0x9f050040 ...OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... [ 0.000000] Linux version 3.3.8 (enable@enable-buildsvr2) (collect2: ld returned 1 exit status) #1 Tue Jan 14 20:12:51 PST 2014 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9342 rev 1 [ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=CR5000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),5696k(rootfs),640k(certs),64k(nvram),64k(art)ro,7104k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61372k/65536k available (2176k kernel code, 4164k reserved, 572k data, 212k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79 [ 0.100000] MIPS: machine is CR5000 Cloud Router [ 0.100000] registering PCI controller with io_map_base unset [ 0.310000] bio: create slab <bio-0> at 0 [ 0.320000] PCI host bridge to bus 0000:00 [ 0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.330000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.330000] pci 0000:00:00.0: invalid calibration data [ 0.340000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 0.350000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.350000] Switching to clocksource MIPS [ 0.360000] NET: Registered protocol family 2 [ 0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.360000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.370000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.370000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.380000] TCP reno registered [ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.390000] NET: Registered protocol family 1 [ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.430000] msgmni has been set to 119 [ 0.430000] io scheduler noop registered [ 0.440000] io scheduler deadline registered (default) [ 0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.470000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.480000] console [ttyS0] enabled, bootconsole disabled [ 0.480000] console [ttyS0] enabled, bootconsole disabled [ 0.490000] m25p80 spi0.0: found mx25l6405d, expected m25p80 [ 0.500000] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 0.500000] 8 cmdlinepart partitions found on MTD device spi0.0 [ 0.510000] Creating 8 MTD partitions on "spi0.0": [ 0.510000] 0x000000000000-0x000000040000 : "u-boot" [ 0.520000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.530000] 0x000000050000-0x0000001b0000 : "kernel" [ 0.530000] 0x0000001b0000-0x000000740000 : "rootfs" [ 0.540000] mtd: partition "rootfs" set to be root filesystem [ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=5F0000, len=150000 [ 0.560000] 0x0000005f0000-0x000000740000 : "rootfs_data" [ 0.560000] 0x000000740000-0x0000007e0000 : "certs" [ 0.570000] 0x0000007e0000-0x0000007f0000 : "nvram" [ 0.580000] 0x0000007f0000-0x000000800000 : "art" [ 0.580000] 0x000000050000-0x000000740000 : "firmware" [ 0.610000] ag71xx_mdio: probed [ 0.740000] ag71xx_mdio: probed [ 0.750000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.320000] eth0: Atheros AR8327 switch driver attached. [ 2.480000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 2.500000] ag71xx_hw_probe: clear tx clock delay [ 2.500000] ag71xx_hw_probe: clear rx clock delay [ 2.510000] TCP cubic registered [ 2.510000] NET: Registered protocol family 17 [ 2.510000] Bridge firewalling registered [ 2.520000] 8021q: 802.1Q VLAN Support v1.8 [ 2.530000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.540000] Freeing unused kernel memory: 212k freed - preinit - - regular preinit - [ 4.690000] JFFS2 notice: (468) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. switching to jffs2 - init - [ 6.060000] Compat-drivers backport release: compat-drivers-2013-01-21-1 [ 6.060000] Backport based on wireless-testing.git master-2013-02-22 [ 6.070000] compat.git: wireless-testing.git [ 6.220000] cfg80211: Calling CRDA to update world regulatory domain [ 6.220000] cfg80211: World regulatory domain updated: [ 6.230000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 6.240000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.250000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.250000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 6.260000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.270000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 6.600000] usbcore: registered new interface driver usbfs [ 6.600000] usbcore: registered new interface driver hub [ 6.610000] usbcore: registered new device driver usb [ 7.200000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47 [ 7.200000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 7.320000] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=40 [ 7.330000] cfg80211: Calling CRDA for country: US [ 7.330000] cfg80211: Regulatory domain changed to country: US [ 7.340000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 7.350000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 7.360000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 7.360000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.370000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.380000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.390000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 7.540000] PPP generic driver version 2.4.2 [ 7.580000] tun: Universal TUN/TAP device driver, 1.6 [ 7.580000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 7.600000] PPP MPPE Compression module registered [ 7.710000] GRE over IPv4 demultiplexor driver [ 7.730000] GRE over IPv4 tunneling driver [ 7.950000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.180000] NET: Registered protocol family 24 [ 8.270000] nf_conntrack version 0.5.0 (962 buckets, 3848 max) [ 8.660000] PPTP driver version 0.8.5 [ 9.320000] xt_time: kernel timezone is -0000 [ 9.790000] Netfilter messages via NETLINK v0.30. [ 9.970000] Ebtables v2.0 registered [ 10.240000] ip_set: protocol 6 [ 10.740000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Please press Enter to activate this console. [ 17.340000] device eth0.3 entered promiscuous mode [ 17.340000] device eth0 entered promiscuous mode [ 18.930000] eth0: link up (1000Mbps/Full duplex) [ 18.940000] br-setup: port 1(eth0.3) entered forwarding state [ 18.950000] br-setup: port 1(eth0.3) entered forwarding state [ 20.950000] br-setup: port 1(eth0.3) entered forwarding state


OpenWrt 18.06.2 bootlog

(19:23:50)U-boot MI124 DRAM: sri Wasp 1.1 wasp_ddr_initial_config(255): (16bit) ddr2 init 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 251k for U-Boot at: 83fc0000 Reserving 192k for malloc() at: 83f90000 Reserving 44 Bytes for Board Info at: 83f8ffd4 Reserving 36 Bytes for Global Data at: 83f8ffb0 Reserving 128k for boot params() at: 83f6ffb0 Stack Pointer at: 83f6ff98Now running in RAM - U-Boot at: 83fc0000 id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MBpcie module ID is correct 0x30168c BOARD IS NOT CALIBRATED!!! In: serial Out: serial Err: serial Net: ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0x7 cfg2 0x7114 Meth0: 00:03:7f:09:0b:ad athrs17_reg_init: comp leteeth0 up eth0 Hit any key to stop autoboot: 6 5 4 3 2 1 0 ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0xf cfg2 0x7114 Meth0: 00:03:7f:09:0b:adeth0 up eth0 ## Booting image at 9f050000 ... Image Name: MIPS OpenWrt Linux-4.9.152 Created: 2019-01-30 12:21:02 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1376708 Bytes = 1.3 MB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum at 0x9f050040 ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 67108864Starting kernel ...[ 0.000000] Linux version 4.9.152 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7549-217219e) ) #0 Mon Jan 28 08:54:32 2019 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9342 rev 1 [ 0.000000] Determined physical RAM map:[ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=CR5000 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7808k(firmware),64k(art)ro console=ttyS0,115200 rootfstype=squashfs noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 60028K/65536K available (3388K kernel code, 175K rwdata, 448K rodata, 268K init, 211K bss, 5508K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns [ 0.000011] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns [ 0.008257] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248) [ 0.091054] pid_max: default: 32768 minimum: 301 [ 0.096052] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.103041] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.113812] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.124231] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.132145] NET: Registered protocol family 16 [ 0.138692] MIPS: machine is PowerCloud CR5000 [ 0.149666] registering PCI controller with io_map_base unset[ 0.387288] Can't analyze schedule() prologue at 803ab68 4 [ 0.406011] PCI host bridge to bus 0000:00 [ 0.410411] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.417654] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.423541] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.430692] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.439584] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.447311] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref][ 0.454968] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.464189] clocksource: Switched to clocksource MIPS [ 0.470839] NET: Registered protocol family 2 [ 0.476587] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.483952] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.490722] TCP: Hash tables configured (established 1024 bind 1024) [ 0.497544] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.503726] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.510680] NET: Registered protocol family 1 [ 0.518788] Crashlog allocated RAM at address 0x3f00000 [ 0.525746] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.540744] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.546943] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.568579] io scheduler noop registered [ 0.572718] io scheduler deadline registered (default) [ 0.578711] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.588626] console [ttyS0] disabled[ 0.612530] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A [ 0.621648] console [ttyS0] enabled [ 0.621648] console [ttyS0] enabled [ 0.629215] bootconsole [early0] disabled [ 0.629215] bootconsole [early0] disabled [ 0.645346] m25p80 spi0.0: found mx25l6405d, expected m25p80 [ 0.651912] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 0.657049] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.663158] Creating 4 MTD partitions on "spi0.0": [ 0.668144] 0x000000000000-0x000000040000 : "u-boot" [ 0.675650] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.683576] 0x000000050000-0x0000007f0000 : "firmware" [ 0.701044] 2 uimage-fw partitions found on MTD device firmware [ 0.707234] 0x000000050000-0x0000001b0000 : "kernel" [ 0.714103] 0x0000001b0000-0x0000007f0000 : "rootfs" [ 0.721322] mtd: device 4 (rootfs) set to be root filesystem [ 0.727279] 1 squashfs-split partitions found on MTD device rootfs [ 0.733684] 0x000000400000-0x0000007f0000 : "rootfs_data" [ 0.741855] 0x0000007f0000-0x000000800000 : "art" [ 0.750436] libphy: Fixed MDIO Bus: probed [ 0.768835] switch0: Atheros AR8327 rev. 2 switch registered on ag71xx-mdio.0 M[ 1.438260] libphy: ag71xx_mdio: probed[ 2.065598] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 2.077438] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 2.086029] NET: Registered protocol family 10 [ 2.095046] NET: Registered protocol family 17 [ 2.099695] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.113262] 8021q: 802.1Q VLAN Support v1.8 [ 2.119675] hctosys: unable to open rtc device (rtc0) [ 2.130347] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 2.139462] Freeing unused kernel memory: 268K [ 2.144058] This architecture does not have kernel memory protection.[ 2.5642 02] random: fast init done[ 2.899459] init: Console is alive [ 2.903243] init: - watchdog - M[ 3.935446] kmodloader: loading kernel modules from /etc/modules-boot.d/*[ 4.009994] usbcore: registered new interface driver usbfs [ 4.015856] usbcore: registered new interface driver hub [ 4.021462] usbcore: registered new device driver usb [ 4.033167] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.041863] ehci-platform: EHCI generic platform driver [ 4.047440] ehci-platform ehci-platform: EHCI Host Controller [ 4.053433] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 4.063764] ehci-pl atform ehci-platform: irq 3, io mem 0x1b000000[ 4.094236] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 4.101787] hub 1-0:1.0: USB hub found [ 4.106129] hub 1-0:1.0: 1 port detected [ 4.111251] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.121397] init: - preinit -[ 4.929451] IPv6: ADDRCONF(NETDEV_U P): eth0: link is not ready[ 4.959584] random: procd: uninitialized urandom read (4 bytes read)Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level[ 5.955452] eth0: link up (1000Mbps/Full duplex) [ 5.960324] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready[ 8.243604] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 8.261858] mount_root: overlay filesystem has not been fully initialized yet [ 8.274151] mount_root: switching to jffs2 overlay M[ 8.311937] urandom-seed: Seed file not found (/etc/urandom.seed) M[ 8.533159] eth0: link down[ 8.550170] procd: - early - [ 8.553279] procd: - watchdog -[ 9.205262] procd: - watchdog - [ 9.208857] procd: - ubus - M[ 9.326376] random: ubusd: uninitialized urandom read (4 bytes read)[ 9.387343] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.394537] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.402306] procd: - init - MPlease press Enter to activate this console.[ 9.794586] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.806705] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 9.827009] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180 [ 9.835358] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d [ 9.845927] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.861964 ] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) M[ 9.934069] xt_time: kernel timezone is -0000[ 10.006411] PPP generic driver version 2.4.2 [ 10.013793] NET: Registered protocol family 24[ 10.087772] ieee80211 phy0: Atheros AR9340 Rev:1 mem=0xb8100000, irq=47 [ 10.094894] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) M[ 10.216325] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=40 M[ 10.420433] kmodloader: done loading kernel modules from /etc/modules.d/*[ 11.881730] urandom_read: 5 callbacks suppressed [ 11.881740] random: jshn: uninitialized urandom read (4 bytes read) [0] 0:picocom* "krswitch" 02:40 14-May-19 M[ 30.177441] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready[ 30.220335] br-lan: port 1(eth0.1) entered blocking state [ 30.225999] br-lan: port 1(eth0.1) entered disabled state [ 30.232063] device eth0.1 entered promiscuous mode [ 30.237082] device eth0 entered promiscuous mode M[ 30.334489] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready[ 30.450217] IP v6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready[ 31.235755] eth0: link up (1000Mbps/Full duplex) [ 31.240619] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready[ 31.350210] br-lan: port 1(eth0.1) entered blocking state [ 31.355862] br-lan: port 1(eth0.1) entered forwarding state [ 31.361820] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready M[ 31.534330] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.28.4 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 18.06.2, r7676-cddd7b4c77 -----------------------------------------------------

OpenWrt snapshot bootlog

U-Boot 1.1.4 (Mar 4 2013 - 19:23:50) U-boot MI124 DRAM: sri Wasp 1.1 wasp_ddr_initial_config(255): (16bit) ddr2 init 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 251k for U-Boot at: 83fc0000 Reserving 192k for malloc() at: 83f90000 Reserving 44 Bytes for Board Info at: 83f8ffd4 Reserving 36 Bytes for Global Data at: 83f8ffb0 Reserving 128k for boot params() at: 83f6ffb0 Stack Pointer at: 83f6ff98 Now running in RAM - U-Boot at: 83fc0000 id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MB pcie module ID is correct 0x30168c BOARD IS NOT CALIBRATED!!! In: serial Out: serial Err: serial Net: ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0x7 cfg2 0x7114 eth0: 00:03:7f:09:0b:ad athrs17_reg_init: complete eth0 up eth0 Hit any key to stop autoboot: 6 5 4 3 2 1 0 ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0xf cfg2 0x7114 eth0: 00:03:7f:09:0b:ad eth0 up eth0 ## Booting image at 9f050000 ... Image Name: MIPS OpenWrt Linux-4.14.118 Created: 2019-05-13 17:17:41 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1703486 Bytes = 1.6 MB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum at 0x9f050040 ...OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... [ 0.000000] Linux version 4.14.118 (buildbot@slashdirt-03) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9992-86fd8cb)) #0 Mon May 13 17:17:41 2019 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] MIPS: machine is PowerCloud Systems CR5000 [ 0.000000] SoC: Atheros AR9342 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x47c with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 57948K/65536K available (4006K kernel code, 162K rwdata, 956K rodata, 1204K init, 211K bss, 7588K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 535.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns [ 0.000011] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns [ 0.008255] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248) [ 0.094824] pid_max: default: 32768 minimum: 301 [ 0.099919] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.106914] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.119494] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.129915] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.136449] pinctrl core: initialized pinctrl subsystem [ 0.144757] NET: Registered protocol family 16 [ 0.157987] PCI host bridge /ahb/apb/pcie-controller@180c0000 ranges: [ 0.164858] MEM 0x0000000010000000..0x0000000013ffffff [ 0.170367] IO 0x0000000000000000..0x0000000000000000 [ 0.195885] PCI host bridge to bus 0000:00 [ 0.200282] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.207532] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.213423] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.220578] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.229534] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.237262] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 0.248404] clocksource: Switched to clocksource MIPS [ 0.255107] NET: Registered protocol family 2 [ 0.260774] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.268140] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.274911] TCP: Hash tables configured (established 1024 bind 1024) [ 0.281786] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.287960] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.294904] NET: Registered protocol family 1 [ 0.303100] Crashlog allocated RAM at address 0x3f00000 [ 0.310200] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.323275] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.329473] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.350771] io scheduler noop registered [ 0.354908] io scheduler deadline registered (default) [ 0.360823] ar7200-usb-phy usb-phy: phy reset is missing [ 0.368702] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68 [ 0.377275] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.387108] console [ttyS0] disabled [ 0.390989] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A [ 0.400109] console [ttyS0] enabled [ 0.400109] console [ttyS0] enabled [ 0.407654] bootconsole [early0] disabled [ 0.407654] bootconsole [early0] disabled [ 0.426714] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 0.431883] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.438463] Creating 4 MTD partitions on "spi0.0": [ 0.443420] 0x000000000000-0x000000040000 : "u-boot" [ 0.449583] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.456004] 0x000000050000-0x0000007f0000 : "firmware" [ 0.465362] 2 uimage-fw partitions found on MTD device firmware [ 0.471545] Creating 2 MTD partitions on "firmware": [ 0.476686] 0x000000000000-0x0000001a0000 : "kernel" [ 0.482807] 0x0000001a0000-0x0000007a0000 : "rootfs" [ 0.488874] mtd: device 4 (rootfs) set to be root filesystem [ 0.494764] 1 squashfs-split partitions found on MTD device rootfs [ 0.501207] 0x0000003b0000-0x0000007a0000 : "rootfs_data" [ 0.507746] 0x0000007f0000-0x000000800000 : "art" [ 0.515027] libphy: Fixed MDIO Bus: probed [ 0.860310] libphy: ag71xx_mdio: probed [ 0.867276] switch0: Atheros AR8327 rev. 2 switch registered on mdio-bus.0 [ 1.529377] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 1.541222] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii [ 1.550655] NET: Registered protocol family 10 [ 1.561974] Segment Routing with IPv6 [ 1.565884] NET: Registered protocol family 17 [ 1.570610] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.584018] 8021q: 802.1Q VLAN Support v1.8 [ 1.591130] hctosys: unable to open rtc device (rtc0) [ 1.601947] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.617117] Freeing unused kernel memory: 1204K [ 1.621837] This architecture does not have kernel memory protection. [ 2.278850] init: Console is alive [ 2.282639] init: - watchdog - [ 2.515600] random: fast init done [ 3.275620] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.413154] usbcore: registered new interface driver usbfs [ 3.419009] usbcore: registered new interface driver hub [ 3.424609] usbcore: registered new device driver usb [ 3.436941] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.445871] ehci-platform: EHCI generic platform driver [ 3.451660] ehci-platform 1b000000.usb: EHCI Host Controller [ 3.457581] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 3.465849] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000 [ 3.498457] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 3.505896] hub 1-0:1.0: USB hub found [ 3.510256] hub 1-0:1.0: 1 port detected [ 3.515839] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.525949] init: - preinit - [ 4.528464] random: jshn: uninitialized urandom read (4 bytes read) [ 4.711682] random: jshn: uninitialized urandom read (4 bytes read) [ 4.942848] random: jshn: uninitialized urandom read (4 bytes read) [ 6.452023] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.458141] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 6.522549] urandom_read: 4 callbacks suppressed [ 6.522558] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.479696] eth0: link up (1000Mbps/Full duplex) [ 7.484554] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.491508] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 9.778464] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 9.816160] urandom-seed: Seed file not found (/etc/urandom.seed) [ 9.939765] eth0: link down [ 9.974867] procd: - early - [ 9.977972] procd: - watchdog - [ 10.673750] procd: - watchdog - [ 10.677343] procd: - ubus - [ 10.709622] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.730570] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.738943] procd: - init - Please press Enter to activate this console. [ 11.203437] kmodloader: loading kernel modules from /etc/modules.d/* [ 11.218471] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.234916] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7 [ 11.242803] Backport generated by backports.git v4.19.32-1-0-g1c4f7569 [ 11.253254] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.270237] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 11.352008] xt_time: kernel timezone is -0000 [ 11.431892] PPP generic driver version 2.4.2 [ 11.439497] NET: Registered protocol family 24 [ 11.516328] ieee80211 phy0: Atheros AR9340 Rev:1 mem=0xb8100000, irq=12 [ 11.523715] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 11.644938] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=14 [ 11.828933] kmodloader: done loading kernel modules from /etc/modules.d/* [ 61.506861] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 61.542586] jffs2_build_filesystem(): unlocking the mtd device... [ 61.542598] done. [ 61.551036] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 66.607848] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 66.667934] br-lan: port 1(eth0.1) entered blocking state [ 66.673591] br-lan: port 1(eth0.1) entered disabled state [ 66.679587] device eth0.1 entered promiscuous mode [ 66.684544] device eth0 entered promiscuous mode [ 66.767828] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 66.861470] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready [ 67.640221] eth0: link up (1000Mbps/Full duplex) [ 67.645075] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 67.710517] br-lan: port 1(eth0.1) entered blocking state [ 67.716113] br-lan: port 1(eth0.1) entered forwarding state [ 67.722300] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready [ 67.898517] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 87.701307] done. [ 87.703348] jffs2: notice: (1124) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 87.904992] overlayfs: upper fs does not support tmpfile. [ 130.748465] random: crng init done BusyBox v1.30.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r9992-86fd8cb ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


Notes

None at present.

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/powercloud_systems/powercloud_systems_cr5000.txt · Last modified: 2019/10/26 07:34 by tmomas