Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revisionBoth sides next revision
toh:openembed:openembed_som9331_v1 [2018/06/22 09:48] – Datatables added, cleanup tmomastoh:openembed:som9331_v1 [2023/03/12 19:12] – [Table] marc0
Line 3: Line 3:
 /* This template is intended to be used via https://openwrt.org/meta/create_new_device_page . */ /* This template is intended to be used via https://openwrt.org/meta/create_new_device_page . */
  
-{{page>meta:infobox:construction&noheader&nofooter&noeditbtn}} +{{page>meta:infobox:construction&noheader&nofooter&noeditbtn}}
- +
-//The SOM9331 is a Single Board Computer (SBC) with 8MiB of NOR flash and 64MiB of ram. It is made by the Chinese manufacturer OpenEmbed and comes in two form factors: a System on Module (SOM) with castellated pins, and an SBC with the hardware peripherals broken out; including 3x100Mb Ethernet ports, USB to UART for debug and a USB Host.//+
  
 +The SOM9331 is a Single Board Computer (SBC) with 8MiB of NOR flash and 64MiB of ram. It is made by the Chinese manufacturer OpenEmbed and comes in two form factors: a System on Module (SOM) with castellated pins, and an SBC with the hardware peripherals broken out; including 3x100Mb Ethernet ports, USB to UART for debug and a USB Host.
 +SOM9331 Ships with OpenWrt 12.09 Attitude Adjustment. 
  
 /*****/ /*****/
Line 43: Line 43:
  
 FIXME Please add the installation procedure here. FIXME Please add the installation procedure here.
- 
- 
-===== OpenWrt support ===== 
- 
-SOM9331 Ships with OpenWrt v12.09 Attitude Adjustment.  
- 
-Cannot find the vendor's stock firmware online but Barrier Breaker v14.07 can be found [[http://openwrt.jaru.eu.org/barrier_breaker/ar71xx/|here]]. 
- 
- 
-===== Supporting activities ===== 
- 
-//There is a github that has a patch for the SOM9331 running OpenWrt v12.09 AA.// 
- 
-  * [[https://github.com/10to7/SOM9331|Github repo]] 
-  
-It adds the new target profile to buildroot and enabled the LED's to work with the ethernet.  
- 
- 
-//__This has not yet been tested__.// 
- 
  
  
Line 170: Line 150:
  
 ==== Opening the case ==== ==== Opening the case ====
- 
-__ATTENTION!__ 
  
 This board does not come in a package, it only comes with a plastic base separated by copper spacers and screwed together. Therefore it is really easy to take it apart. This board does not come in a package, it only comes with a plastic base separated by copper spacers and screwed together. Therefore it is really easy to take it apart.
- 
  
 All you will need is a Phillips head screw driver. All you will need is a Phillips head screw driver.
  
-Use the Following steps to remove the base:+Use the following steps to remove the base:
  
-      1. Remove the four screws from the top of the device, using your Phillips head screwdriver. +  - Remove the four screws from the top of the device, using your Phillips head screwdriver. 
-      2. Remove the plastic casing from the bottom.+  Remove the plastic casing from the bottom.
  
 +You now have access to the front and back of the pcb.
  
-You now have access to the front and back of the pcb. 
 ==== Serial ==== ==== Serial ====
 -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc. -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc.
Line 199: Line 176:
 </WRAP> </WRAP>
  
-^ Serial connection parameters\\ for OpenEmbed SOM9331 v1 | EXAMPLE 115200, 8N1 |+^ Serial connection parameters\\ for OpenEmbed SOM9331 v1  | 115200, 8N1  |
  
 ==== JTAG ==== ==== JTAG ====
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1