| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision |
| toh:netgear:wnr1000_v2 [2019/06/24 05:26] – OpenWrt spelling tmomas | toh:netgear:wnr1000_v2 [2020/09/15 21:36] – [Netgear WNR1000 v2] jlpapple |
|---|
| {{section>meta:infobox:432_warning#infobox_for_dataentries&noheader&nofooter&noeditbutton}} | {{section>meta:infobox:432_warning#infobox_for_dataentries&noheader&nofooter&noeditbutton}} |
| |
| WNR1000-100PES - very similar to [[toh:netgear:wnr2000|WNR2000v3]] / [[toh:netgear:wnr612v2|WNR612v2]] | **Note:** Official images are too large as of 17.XX. Use the Community Builds in the forum topic URL below for the latest 17.XX, 18.XX, and 19.XX images. https://forum.openwrt.org/t/builds-for-netgear-wnr1000v2-wnr1000v2-vc-wnr612v2-wpn824n-wnr2000v3/39360 |
| |
| | WNR1000-100PES - very similar to [[toh:netgear:wnr2000|WNR2000v3]] / [[toh:netgear:wnr612v2|WNR612v2]] |
| |
| | WNR1000v2 also exists as WNR1000v2h2 - instructions for WNR1000v2 also work for WNR1000v2h2 without modification. |
| ===== Supported Versions ===== | ===== Supported Versions ===== |
| ---- datatable ---- | ---- datatable ---- |
| -> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]] | -> [[docs:guide-user:installation:generic.flashing|Install OpenWrt (generic explanation)]] |
| |
| FIXME Please add the installation procedure here. | **Note:** Ready-to-install firmware images for OpenWrt 17.01.7 and 18.06.8 and 19.07.3 are available as of June 2020 [[https://forum.openwrt.org/t/wnr1000v2-builds-for-netgear/39360|via OpenWrt Community Builds]]. These are customized builds that do include opkg due to inadequate flash size that cause stock, official OpenWrt builds to bootloop or not retain settings upon reboot. |
| |
| **Note:** Ready-to-install firmware images for OpenWrt 17.01.6 and 18.06.2 are available as of June 2019 [[https://forum.openwrt.org/t/wnr1000v2-builds-for-netgear/39360|via OpenWrt Community Builds]]. These are customized builds that do not include IPV6, PPP, opkg due to inadequate flash size that cause stock OpenWrt builds to bootloop or not retain settings upon reboot. The official OpenWrt images for these devices do not work as of June 2019. | [[https://forum.openwrt.org/t/wnr1000v2-builds-for-netgear/39360|Updated Installation Instructions]] |
| |
| - - - | - - - |
| ==== GPIO ==== | ==== GPIO ==== |
| |
| GPIO LEDs and buttons on this device are connected to either AR7240 SoC or AR9285 wireless chip, so not all of them are accessible to stock version of OpenWrt 15.05 (generic ath9k driver does not register AR9285 GPIOs in kernel). Please read more in __Patches__ section below about current status of addressing these issues. | GPIO LEDs and buttons on this device are connected to GPIO controllers on AR7240 SoC and AR9285 wireless chip. |
| |
| Controlled by **AR7240** SoC (18 GPIOs total, LAN LEDs shared with built-in Ethernet switch) : | Controlled by **AR7240** SoC (18 GPIOs total, LAN LEDs shared with built-in Ethernet switch) : |
| ^ Type ^ Function ^ GPIO ^ Polarity ^ Notes ^ | ^ Type ^ Function ^ GPIO ^ Polarity ^ Notes ^ |
| | LED | WAN AMBER | 0 (0, 0) | active low | | | | LED | WAN AMBER | 0 (0, 0) | active low | | |
| | LED | TEST AMBER | 1 (0, 1) | active low | aka POWER AMBER - see note [3] | | | LED | POWER AMBER | 1 (0, 1) | active low | aka TEST AMBER - see note [3] | |
| | LED | LAN1 AMBER | 6 (0, 6) | active low | shared with JTAG - see note [0] | | | LED | LAN1 AMBER | 6 (0, 6) | active low | shared with JTAG - see note [0] | |
| | LED | LAN2 AMBER | 7 (0, 7) | active low | shared with JTAG - see note [0] | | | LED | LAN2 AMBER | 7 (0, 7) | active low | shared with JTAG - see note [0] | |
| | LED | WAN GREEN | 17 (0, 17) | active low | link activity - see note [1] | | | LED | WAN GREEN | 17 (0, 17) | active low | link activity - see note [1] | |
| |
| Controlled by **AR9285** wireless chip (12 GPIOs total, unaccessible with default ath9k driver, see __Patches__ section below) : | Controlled by **AR9285** wireless chip (12 GPIOs total) : |
| ^ Type ^ Function ^ GPIO ^ Polarity ^ Notes ^ | ^ Type ^ Function ^ GPIO ^ Polarity ^ Notes ^ |
| | LED | WLAN BLUE | 53 (1, 1) | active low | not all triggers work - see note [2] | | | LED | WLAN BLUE | 53 (1, 1) | active low | not all triggers work - see note [2] | |
| *//[2] - 'phy0radio' trigger does not work, use default 'phy0tpt' or 'wlan0' netdevice instead// | *//[2] - 'phy0radio' trigger does not work, use default 'phy0tpt' or 'wlan0' netdevice instead// |
| *//[3] - this is amber light on power LED (labelled TEST in u-boot sources)// | *//[3] - this is amber light on power LED (labelled TEST in u-boot sources)// |
| |
| === Patches === | |
| |
| Patches providing full GPIO support on WNR2000v3 / WNR612v2 / WNR1000v2 have been submitted to trunk ([[https://patchwork.ozlabs.org/project/openwrt/list/?submitter=68145]]). They are included in OpenWrt starting from version r49077.\\ | |
| All above patches and their versions backported to Chaos Chalmer (15.05) are available at [[https://micu.webserwer.pl/pmwiki/pmwiki.php?n=OpenWRT.Patches]]. | |
| |
| === GPIO in OpenWrt === | === GPIO in OpenWrt === |
| gpio-60 (rfkill ) in hi | gpio-60 (rfkill ) in hi |
| </code> | </code> |
| | |
| | ===== Custom u-boot ===== |
| | |
| | There is a project allowing to build custom u-boot image https://github.com/realmicu/uboot-wnrmod2k |
| | It could be used if flash memory chip was replaced or to obtain additional functionality. |
| |
| ===== Tags ===== | ===== Tags ===== |
| [[meta:tags|How to add tags]] | [[meta:tags|How to add tags]] |
| {{tag>4flash 32ram AR7240}} | {{tag>4flash 32ram AR7240}} |