Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:netgear:wn802t [2013/08/06 11:12] airetoh:netgear:wn802t [2015/12/14 18:11] – New bootlog formatting applied tmomas
Line 1: Line 1:
 +====== Netgear WN802T ======
  
 +The WN802T is a b/g/n wireless access point, capable of running OpenWRT. 
 +
 +===== Version 2.x =====
 +
 +
 +==== Features ====
 +  * Atheros AR9132 CPU
 +  * 8 MB Flash Memory
 +  * 32 MB DDR400B RAM (Hynix HY5DU561622FTP-D43) 
 +  * Atheros AR9103 wireless chip
 +  * Atheros AR8021 Ethernet chip
 +
 +==== Serial console ====
 +
 +The serial console connector (JP1) has the usual Netgear pinout: GND - TX - RX - VCC
 +
 +It's 115200 8N1, software flow control. It's a TTL serial port, so don't plug it directly into a RS232 port. You have to build a TTL-RS232 adaptor to attach your WN802T to your computer. With that, you can now use a null modem cable to attach it to your PCs COM port. 
 +
 +To access the boot menu, press space bar when you see "Enter SPACE to drop into boot loader:" and countdown from 5 to zero.
 +
 +The ethernet port is enabled in the boot loader (cable must be plugged in on boot). TFTP can be used to transfer the firmware.
 +
 +==== BootLogs ====
 +
 +
 +=== Factory Bootlog ===
 +<WRAP bootlog>
 +<nowiki>U-Boot 1.1.4-WN802TV2-V1.1.2 (Sep  3 2009 - 10:09:11)
 +
 +AP83 (ar9100 with SPI flash)
 +DRAM:  32 MB
 +        Finding MXIC Flash. ID c22017
 +Flash:  8 MB
 +In:    serial
 +Out:   serial
 +Err:   serial
 +Net:   ag7100_enet_initialize...
 +        Fetching MAC Address from 0xbf7f1000
 +        MAC_CFG1 0xf MAC_CFG2 0x7114
 +        PHY Setting up...
 +        VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
 +PHY:   Atheros AR8021
 +eth0:  00:00:00:00:00:00
 +        eth0 up
 +
 +Manu data is valid!
 +Enter SPACE to drop into boot loader:  0
 +## Booting image at bf6e0000 ...
 +   Image Name:   Linux Kernel Image
 +   Created:      2012-06-07   6:12:17 UTC
 +   Image Type:   MIPS Linux Kernel Image (gzip compressed)
 +   Data Size:    913746 Bytes = 892.3 kB
 +   Load Address: 80060000
 +   Entry Point:  8022d000
 +   Verifying Kernel Checksum ... OK
 +   Uncompressing Kernel Image ... OK
 +
 +Starting kernel @8022d000...
 +
 +Linux version 2.6.15--LSDK-7.1.3.29-WN802Tv2_V3.1.12 (root@localhost.localdomain) (gcc version 3.4.4) #200 Thu Jun 7 11:42:02 IST 2012
 +flash_size passed from bootloader = 8
 +arg 1: console=ttyS0,115200
 +arg 2: rootfstype=jffs2
 +arg 3: root=31:02
 +init=/sbin/init
 +arg 4: mtdparts=ar7100-nor0:256k(u-boot),64k(u-boot-env),6720k(rootfs),1024k(uImage),64k(manufacturing-data),64k(ART)
 +arg 5: mem=32M
 +CPU revision is: 00019374
 +Determined physical RAM map:
 + memory: 02000000 @ 00000000 (usable)
 +User-defined physical RAM map:
 + memory: 02000000 @ 00000000 (usable)
 +Built 1 zonelists
 +Kernel command line: console=ttyS0,115200 rootfstype=jffs2 root=31:02
 +init=/sbin/init mtdparts=ar7100-nor0:256k(u-boot),64k(u-boot-env),6720k(rootfs),1024k(uImage),64k(manufacturing-data),64k(ART) mem=32M
 +Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
 +Primary data cache 32kB, 4-way, linesize 32 bytes.
 +Synthesized TLB refill handler (20 instructions).
 +Synthesized TLB load handler fastpath (32 instructions).
 +Synthesized TLB store handler fastpath (32 instructions).
 +Synthesized TLB modify handler fastpath (31 instructions).
 +Cache parity protection disabled
 +PID hash table entries: 256 (order: 8, 4096 bytes)
 +Using 200.000 MHz high precision timer.
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 30020k/32768k available (1520k kernel code, 2732k reserved, 319k data, 104k init, 0k highmem)
 +Mount-cache hash table entries: 512
 +Checking for 'wait' instruction...  available.
 +NET: Registered protocol family 16
 +reset dev success
 +SCSI subsystem initialized
 +AR7100 GPIOC major 0
 +JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
 +Initializing Cryptographic API
 +io scheduler noop registered
 +io scheduler deadline registered
 +Serial: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled
 +serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A
 +6 cmdlinepart partitions found on MTD device ar7100-nor0
 +Creating 6 MTD partitions on "ar7100-nor0":
 +0x00000000-0x00040000 : "u-boot"
 +0x00040000-0x00050000 : "u-boot-env"
 +0x00050000-0x006e0000 : "rootfs"
 +0x006e0000-0x007e0000 : "uImage"
 +0x007e0000-0x007f0000 : "manufacturing-data"
 +0x007f0000-0x00800000 : "ART"
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 512 (order: -1, 2048 bytes)
 +TCP established hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +TCP bic registered
 +NET: Registered protocol family 1
 +NET: Registered protocol family 17
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +ar7100wdt_init: Registering WDT success
 +VFS: Mounted root (jffs2 filesystem) readonly.
 +Freeing unused kernel memory: 104k freed
 +init started:  BusyBox v1.01 (2012.06.07-06:08+0000) multi-call binary
 +ag7100_mod: module license 'unspecified' taints kernel.
 +AG7100: Length per segment 1536
 +AG7100: Max segments per packet 1
 +AG7100: Max tx descriptor count    100
 +AG7100: Max rx descriptor count    252
 +AG7100: fifo cfg 3 00780008
 +AG7100CHH: Mac address for unit 0
 +AG7100CHH: e0:91:f5:cd:31:90
 +*** Loading wlandriver
 +*** Country code is 840
 +*** Base MAC address is 00:00:00:00:00:00
 +ath_hal: 0.9.17.1 ( AR5416,DEBUG,REGOPS_FUNC,DFS)
 +asc: no version for "ath_hal_tx_txpc" found: kernel tainted.
 +arada_softchip: 0.1.0.0
 +ath ratectrl: ath_rate_atherosCopyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
 +wlan: mac acl policy registered
 +ath_ahb: 1.0 (Atheros/multi-bss)
 + In asc_attach , enable_pktlog = 0
 +ath ratectrl: ath_rate_atherosCopyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
 +mac 20.0 phy 10.2 radio 13.0
 +wifi0: Atheros AR9100 WiSoC: mem=0xb80c0000, irq=2
 +Creating AP mode
 +Creating wds vaps
 +*** Starting configd
 +*** Starting watchdog
 +*** Starting reset_detect
 +wn802t_reset_open: called
 +wn302t_sys_ioctl: cmd issued is  1015
 +*** Starting httpd server
 +1999-12-31 16:00:05: (server.c.918) WARNING: unknown config-key: accesslog.filename (ignored)
 +*** Creating soft link for syslog binary
 +ln: /bin/syslogd: File exists
 +*** Creating softlink for syslog messages
 +killall: syslogd: no process killed
 +passwd: Unknown user admin
 +
 +kill: Could not kill pid '129': No such process
 +time-b.netgear.com: Unknown host
 +device eth0 entered promiscuous mode
 +ag7100_ring_alloc Allocated 1200 at 0x81ee6000
 +ag7100_ring_alloc Allocated 3024 at 0x818f4000
 +AG7100: cfg1 0xf cfg2 0x7014
 +VSC8601: Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
 +VSC8601: PHY is an Atheros F1E
 +VSC8601: unit 0  phy_addr 1
 +VSC8601: unit 0  phy_addr 1
 +AG7100: unit 0: phy not up carrier 1
 +Writing 4
 +never heard of command [brtrunk]
 +Usage: brctl [commands]
 +commands:
 +        addbr           <bridge>                add bridge
 +        delbr           <bridge>                delete bridge
 +        addif           <bridge> <device>       add idevice wifi0vap0 entered promiscuous mode
 +nterface to bridge
 +        delif           <bridge> <device>       delete interface from bridge
 +        setageing       <bridge> <time>         set ageing time
 +        setbridgeprio   <bridge> <prio>         set bridge prioritdevice wifi0wds0 entered promiscuous mode
 +y
 +        setfd           <bridge> <time>         set bridge forward delay
 +        sethello        <bridge> <time>         set hello time
 +        setmaxage       <bridge> <time>         set max message age
 +        setpathcost     <bridge> <device wifi0wds1 entered promiscuous mode
 +port> <cost>    set path cost
 +        setportprio     <bridge> <port> <prio>  set port priority
 +        show                                    show a list of bridges
 +        showmacs        <bridge>                show a list of mac addrs
 +        showsdevice wifi0wds2 entered promiscuous mode
 +tp      <bridge>                show bridge stp info
 +        stp             <bridge> {on|off}       turn stp on/off
 +device wifi0wds3 entered promiscuous mode
 +device wifi0wds4 entered promiscuous mode
 +device wifi0wds5 entered promiscuous mode
 +route: SIOC[ADD|DEL]RT: Invalid argument
 +no /usr/sbin/nmbd found; none killed.
 +brtrunk: port 2(wifi0vap0) entering learning state
 +brtrunk: port 2(wifi0vap0) entering disabled state
 +brtrunk: port 2(wifi0vap0) entering learning state
 +VSC8601: unit 0  phy_addr 1
 +AG7100: unit 0 phy is up...RGMii 1000Mbps full duplex
 +AG7100: pll reg 0x18050014: 0x13000a44  AG7100: cfg_1: 0x7ff0000
 +AG7100: cfg_2: 0xfff
 +AG7100: cfg_3: 0x780008
 +AG7100: cfg_4: 0xffff
 +AG7100: cfg_5: 0x7ffef
 +AG7100: done cfg2 0x7115 ifctl 0x10000 miictrl 0x12
 +brtrunk: port 1(eth0) entering learning state
 +
 + netgearCD3190 mips #200 Thu Jun 7 11:42:02 IST 2012 (none)
 +netgearCD3190 login: Value = 3
 +brtrunk: topology change detected, propagating
 +brtrunk: port 2(wifi0vap0) entering forwarding state
 +brtrunk: topology change detected, propagating
 +brtrunk: port 1(eth0) entering forwarding state
 +
 + netgearCD3190 mips #200 Thu Jun 7 11:42:02 IST 2012 (none)
 +netgearCD3190 login: root
 +Password:
 +
 +
 +BusyBox v1.01 (2012.06.07-06:08+0000) Built-in shell (ash)
 +Enter 'help' for a list of built-in commands.
 +
 +~ # cat /proc/cpuinfo
 +system type             : Atheros AR9100
 +processor               : 0
 +cpu model               : MIPS 24K V7.4
 +BogoMIPS                : 265.21
 +wait instruction        : yes
 +microsecond timers      : yes
 +tlb_entries             : 16
 +extra interrupt vector  : yes
 +hardware watchpoint     : yes
 +ASEs implemented        : mips16
 +VCED exceptions         : not available
 +VCEI exceptions         : not available
 +~ # cat /proc/meminfo
 +MemTotal:        30140 kB
 +MemFree:         19860 kB
 +Buffers:             0 kB
 +Cached:           2624 kB
 +SwapCached:          0 kB
 +Active:           1860 kB
 +Inactive:         1504 kB
 +HighTotal:           0 kB
 +HighFree:            0 kB
 +LowTotal:        30140 kB
 +LowFree:         19860 kB
 +SwapTotal:           0 kB
 +SwapFree:            0 kB
 +Dirty:               0 kB
 +Writeback:           0 kB
 +Mapped:           2188 kB
 +Slab:             5056 kB
 +CommitLimit:     15068 kB
 +Committed_AS:     7664 kB
 +PageTables:        180 kB
 +VmallocTotal:  1048560 kB
 +VmallocUsed:      1504 kB
 +VmallocChunk:  1046772 kB
 +~ # cat /proc/mtd
 +dev:    size   erasesize  name
 +mtd0: 00040000 00010000 "u-boot"
 +mtd1: 00010000 00010000 "u-boot-env"
 +mtd2: 00690000 00010000 "rootfs"
 +mtd3: 00100000 00010000 "uImage"
 +mtd4: 00010000 00010000 "manufacturing-data"
 +mtd5: 00010000 00010000 "ART"
 +~ # cat /proc/partitions
 +major minor  #blocks  name
 +
 +  31            256 mtdblock0
 +  31             64 mtdblock1
 +  31           6720 mtdblock2
 +  31           1024 mtdblock3
 +  31             64 mtdblock4
 +  31             64 mtdblock5
 +~ # cat /proc/version
 +Linux version 2.6.15--LSDK-7.1.3.29-WN802Tv2_V3.1.12 (root@localhost.localdomain) (gcc version 3.4.4) #200 Thu Jun 7 11:42:02 IST 2012
 +~ #</nowiki>
 +</WRAP>\\
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>atheros-ap83}}
  • Last modified: 2021/12/05 11:52
  • by tmomas