Netgear SRR60

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The SRR60 is the router part of the SRK60 kit, which consists of a router and one or more satellites, all of them being AC-3000 devices.

None at this time.

NMRPflash Method

Download nmrpflash
Put the OpenWRT factory image file in the same folder of the nmrpflash executable
Connect your PC to the router using the port near the power button
Start nmrpflash. Replace XXX with your network interface (can be identified by running nmrpflash -L) and FILE with the file you downloaded

$ nmrpflash -i XXX -f FILE

Power on the router and wait for the flash to complete

After about a minute the router should boot directly to OpenWRT. If nothing happens try to reboot the router. If you have problems flashing try to set “10.164.183.253” as your computer IP address.

Vendor-UI Method

The Vendor web interface will always flash on the partition currently not booted, so to flash OpenWRT for the first time you have to switch to boot partition 2 and then flash the factory image directly from the Vendor web interface. To switch on partition 2 you have to enable telnet first.

Go to http://192.168.1.250/debug.htm and check “Enable Telnet”.
Connect through telnet and login using admin/password.

$ telnet 192.168.1.250

Read the current boot partition

$ artmtd -r boot_part

Write the new boot_part

$ artmtd -w boot_part 02

Reboot and re-check that the currently booted partition is partition 2
Flash the OpenWRT image trough the Vendor-UI

Revert to stock firmware

Download the stock firmware from official NETGEAR support
Follow the nmrpflash procedure like above, using the official Netgear firmware (for example SRR60-V2.2.1.210.img)

$ nmrpflash -i XXX -f FILE

Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

→ generic.sysupgrade

→ generic.debrick

→ failsafe_and_factory_reset

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	EXAMPLE LAN & WiFi	EXAMPLE 192.168.1.1/24
vlan0 (eth0.0)	EXAMPLE LAN ports (1 to 4)	EXAMPLE None
vlan1 (eth0.1)	EXAMPLE WAN port	EXAMPLE DHCP
wl0	EXAMPLE WiFi	EXAMPLE Disabled

Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port	Switch port
Internet (WAN)	EXAMPLE 4
LAN 1	EXAMPLE 3
LAN 2	EXAMPLE 2
LAN 3	EXAMPLE 1
LAN 4	EXAMPLE 0

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The Netgear SRR60 has the following buttons:

BUTTON	Event
Reset	restart
Sync	WPS

Front:

Back:

Backside label:

→ Warranty

1. Cut trough the rubber feet and bottom label, following the slit of the case

2. Remove the label around the ports to reveal the screws

3. Unscrew the two screws using a TX10 (Torx) bit

4. Carefully! slide the front side down and take it off

Main PCB:

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

Serial connection parameters for Netgear SRR60	115200, 8N1, Voltage unknown

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

→ bootloader

None so far.

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 S - IMAGE_VARIANT_STRING=DAAAANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000023 S - Reset status Config, 0x00000000 S - Core 0 Frequency, 0 MHz B - 262 - PBL, Start B - 1343 - bootable_media_detect_entry, Start B - 39962 - bootable_media_detect_success, Start B - 39976 - elf_loader_entry, Start B - 42188 - auth_hash_seg_entry, Start B - 44361 - auth_hash_seg_exit, Start B - 81476 - elf_segs_hash_verify_entry, Start B - 196807 - PBL, End B - 196831 - SBL1, Start B - 289039 - pm_device_init, Start D - 9 - pm_device_init, Delta B - 290558 - boot_flash_init, Start D - 37182 - boot_flash_init, Delta B - 332048 - boot_config_data_table_init, Start D - 2714 - boot_config_data_table_init, Delta - (419 Bytes) B - 339715 - clock_init, Start D - 7541 - clock_init, Delta B - 351025 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 B - 354432 - sbl1_ddr_set_params, Start B - 359526 - cpr_init, Start D - 2 - cpr_init, Delta B - 363909 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13172 - sbl1_ddr_set_params, Delta B - 377206 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 448463 - sbl1_wait_for_ddr_training, Start D - 27 - sbl1_wait_for_ddr_training, Delta B - 464667 - Image Load, Start D - 15025 - QSEE Image Loaded, Delta - (268920 Bytes) B - 480121 - Image Load, Start D - 898 - SEC Image Loaded, Delta - (0 Bytes) B - 489974 - Image Load, Start D - 12663 - APPSBL Image Loaded, Delta - (421607 Bytes) B - 503063 - QSEE Execution, Start D - 60 - QSEE Execution, Delta B - 509239 - SBL1, End D - 314521 - SBL1, Delta S - Flash Throughput, 25171 KB/s (691298 Bytes, 27463 us) S - DDR Frequency, 672 MHz U-Boot 2012.07-g9274bc2-dirty [Barrier Breaker unknown,unknown] (Jun 16 2017 - 16:27:21) U-boot dni1 V1.1 for DNI HW ID: 29765352; NOR flash 0MB; EMMC flash 4096MB; RAM 512MB smem ram ptable found: ver: 1 len: 3 DRAM: 512 MiB machid : 0x8010001 NAND: ID = 0 Vendor = 0 Device = 0 Nand Flash error. Status = 64 ONFI Read id cmd failed ONFI probe failed SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 0 MiB MMC: qca_mmc: 0 *** Warning - bad CRC, using default environment PCI0 Link Intialized In: serial Out: serial Err: serial Valid chip addresses: 27 48 machid: 8010001 flash_type: 1 Net: MAC0 addr:38:94:ed:d1:7a:40 PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Hit any key to stop autoboot: 2 1 0 eth0 PHY0 Down Speed :10 Half duplex eth0 PHY1 Down Speed :10 Half duplex eth0 PHY2 Down Speed :10 Half duplex eth0 PHY3 Down Speed :10 Half duplex eth0 PHY4 Down Speed :10 Half duplex nmrp server is stopped or failed ! Read BootPart from BOARD DATA... mmc_read will run command: mmc read 0x871cfba8 0x2c22 0x100 MMC read: dev # 0, block # 11298, count 256 ... 256 blocks read: OK boot partition : 1 BootPart = 1 Loading DNI firmware for checking... MMC read: dev # 0, block # 18466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24610, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24866, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25122, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25378, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25634, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25890, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26146, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26402, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26658, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26914, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27170, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27426, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27682, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27938, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28194, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28450, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28706, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28962, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29218, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29474, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29730, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29986, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30242, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30498, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30754, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31010, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31266, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31522, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31778, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32034, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32290, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32546, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32802, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33058, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33314, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33570, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33826, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34082, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34338, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34594, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34850, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35106, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35362, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35618, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35874, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36130, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36386, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36642, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36898, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37154, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37410, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37666, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37922, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38178, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38434, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38690, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38946, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39202, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39458, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39714, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39970, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40226, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40482, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40738, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40994, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41250, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41506, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41762, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42018, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42274, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42530, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42786, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43042, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43298, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43554, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43810, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44066, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44322, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44578, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44834, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45090, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45346, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45602, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45858, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46114, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46370, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46626, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46882, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47138, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47394, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47650, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47906, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48162, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48418, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48674, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48930, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49186, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49442, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49698, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49954, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50210, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56610, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56866, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57122, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57378, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57634, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57890, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58146, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58402, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58658, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58914, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59170, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59426, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59682, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59938, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60194, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60450, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60706, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60962, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61218, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61474, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61730, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61986, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62242, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62498, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62754, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63010, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63266, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63522, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63778, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64034, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64290, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64546, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64802, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65058, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65314, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65570, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65826, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66082, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66338, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66594, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66850, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67106, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67362, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67618, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67874, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68130, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68386, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68642, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68898, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69154, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69410, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69666, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69922, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70178, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70434, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70690, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70946, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71202, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71458, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71714, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71970, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 72226, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 72482, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 72738, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 72994, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 73250, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 73506, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 73762, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 74018, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 74274, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 74530, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 74786, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 75042, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 75298, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 75554, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 75810, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 76066, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 76322, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 76578, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 76834, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 77090, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 77346, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 77602, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 77858, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 78114, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 78370, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 78626, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 78882, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 79138, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 79394, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 79650, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 79906, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 80162, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 80418, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 80674, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 80930, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 81186, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 81442, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 81698, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18466, count 1 ... 1 blocks read: OK ** rootfs address : 0x843dffc0 ** ## Checking Image at 84000000 ... FIT image found FIT description: ARM OpenWrt FIT (Flattened Image Tree) Image 0 (kernel@1) Description: ARM OpenWrt Linux-3.14.77 Type: Kernel Image Compression: gzip compressed Data Start: 0x840000e4 Data Size: 3651472 Bytes = 3.5 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 370eedd4 Hash algo: sha1 Hash value: f278dd5addecd5cb8acd59a4e6a95a4f33202deb Image 1 (fdt@1) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8437b9b4 Data Size: 39067 Bytes = 38.2 KiB Architecture: ARM Hash algo: crc32 Hash value: 2fbe7ae7 Hash algo: sha1 Hash value: 10a7fad2926d324e8b06b192c3531c391f78a6ed Image 2 (fdt@2) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8438535c Data Size: 43035 Bytes = 42 KiB Architecture: ARM Hash algo: crc32 Hash value: 3ec0046d Hash algo: sha1 Hash value: f68529aa5c64ac8fb3df893db744ab87366cdd3e Image 3 (fdt@3) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8438fc84 Data Size: 42101 Bytes = 41.1 KiB Architecture: ARM Hash algo: crc32 Hash value: 0109faf0 Hash algo: sha1 Hash value: 34ee6bdafd6315d361d6aa99b5ad45a9944b32dd Image 4 (fdt@4) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8439a208 Data Size: 34248 Bytes = 33.4 KiB Architecture: ARM Hash algo: crc32 Hash value: 0fa6ee98 Hash algo: sha1 Hash value: dcec33a744cfed6a21c9a9be313791f98b1081ff Image 5 (fdt@5) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843a28dc Data Size: 34407 Bytes = 33.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 96f6beb1 Hash algo: sha1 Hash value: 3a938e8901b816f4fa7d73aacbc3e2b54422c5d0 Image 6 (fdt@6) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843ab050 Data Size: 34547 Bytes = 33.7 KiB Architecture: ARM Hash algo: crc32 Hash value: ce835bd9 Hash algo: sha1 Hash value: f48535f83fe16c4d3471b18ddab6dfa5d1a633e7 Image 7 (fdt@7) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843b3850 Data Size: 38588 Bytes = 37.7 KiB Architecture: ARM Hash algo: crc32 Hash value: bb010bc8 Hash algo: sha1 Hash value: a52a0530438afae1fe5fed13cb380503d0ee576b Image 8 (fdt@8) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843bd018 Data Size: 38467 Bytes = 37.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 311234ec Hash algo: sha1 Hash value: c7be34f25ccb51f0d0eaa6985af77d30b872eaef Image 9 (fdt@9) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843c6768 Data Size: 38165 Bytes = 37.3 KiB Architecture: ARM Hash algo: crc32 Hash value: f91b53ee Hash algo: sha1 Hash value: 7f783a91e42dc651bb82f01479f5207640db0d53 Default Configuration: 'config@1' Configuration 0 (config@1) Description: OpenWrt Kernel: kernel@1 FDT: fdt@1 Configuration 1 (config@2) Description: OpenWrt Kernel: kernel@1 FDT: fdt@2 Configuration 2 (config@3) Description: OpenWrt Kernel: kernel@1 FDT: fdt@3 Configuration 3 (config@4) Description: OpenWrt Kernel: kernel@1 FDT: fdt@4 Configuration 4 (config@5) Description: OpenWrt Kernel: kernel@1 FDT: fdt@5 Configuration 5 (config@6) Description: OpenWrt Kernel: kernel@1 FDT: fdt@6 Configuration 6 (config@7) Description: OpenWrt Kernel: kernel@1 FDT: fdt@7 Configuration 7 (config@8) Description: OpenWrt Kernel: kernel@1 FDT: fdt@8 Configuration 8 (config@9) Description: OpenWrt Kernel: kernel@1 FDT: fdt@9 ## Checking hash(es) for FIT Image at 84000000 ... Hash(es) for Image 0 (kernel@1): crc32+ sha1+ Hash(es) for Image 1 (fdt@1): crc32+ sha1+ Hash(es) for Image 2 (fdt@2): crc32+ sha1+ Hash(es) for Image 3 (fdt@3): crc32+ sha1+ Hash(es) for Image 4 (fdt@4): crc32+ sha1+ Hash(es) for Image 5 (fdt@5): crc32+ sha1+ Hash(es) for Image 6 (fdt@6): crc32+ sha1+ Hash(es) for Image 7 (fdt@7): crc32+ sha1+ Hash(es) for Image 8 (fdt@8): crc32+ sha1+ Hash(es) for Image 9 (fdt@9): crc32+ sha1+ ## Checking Image at 843dffc0 ... Legacy image found Image Name: ARM OpenWrt Linux-3.14.77 Image Type: ARM Linux Kernel Image (lzma compressed) Data Size: 28313600 Bytes = 27 MiB Load Address: 40908000 Entry Point: 40908000 Verifying Checksum ... OK mmc_read will run command: mmc read 0x871cfba8 0x2c22 0x100 MMC read: dev # 0, block # 11298, count 256 ... 256 blocks read: OK boot partition : 1 MMC read: dev # 0, block # 18466, count 7680 ... 7680 blocks read: OK ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM OpenWrt Linux-3.14.77 Type: Kernel Image Compression: gzip compressed Data Start: 0x840000e4 Data Size: 3651472 Bytes = 3.5 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 370eedd4 Hash algo: sha1 Hash value: f278dd5addecd5cb8acd59a4e6a95a4f33202deb Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt@1' FDT blob subimage Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8437b9b4 Data Size: 39067 Bytes = 38.2 KiB Architecture: ARM Hash algo: crc32 Hash value: 2fbe7ae7 Hash algo: sha1 Hash value: 10a7fad2926d324e8b06b192c3531c391f78a6ed Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x8437b9b4 Uncompressing Kernel Image ... OK Loading Device Tree to 871e3000, end 871ef89a ... OK Using machid 0x8010001 from environment Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 3.14.77 (june.lin@CNXMDNICP02) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r35193) ) #1 SMP PREEMPT Fri Sep 17 09:23:09 CST 2021 CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK04.1-C1 Flash name: EMMC Memory policy: Data cache writealloc PERCPU: Embedded 8 pages/cpu @dfbc7000 s9088 r8192 d15488 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 128768 Kernel command line: rootwait clk_ignore_unused user_debug=0xff PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 506888K/519168K available (5086K kernel code, 346K rwdata, 1584K rodata, 184K init, 293K bss, 12280K reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0208000 - 0xc088baec (6671 kB) .init : 0xc088c000 - 0xc08ba380 ( 185 kB) .data : 0xc08bc000 - 0xc0912948 ( 347 kB) .bss : 0xc0912948 - 0xc095be8c ( 294 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Preemptible hierarchical RCU implementation. NR_IRQS:16 nr_irqs:16 16 Architected cp15 timer(s) running at 48.00MHz (virt). sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns Switching to timer-based delay loop Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x802131c8 - 0x80213220 CPU1: Booted secondary processor i2c devices info CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU2: Booted secondary processor i2c devices info CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 CPU3: Booted secondary processor i2c devices info CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 Brought up 4 CPUs SMP: Total of 4 processors activated (384.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 2048 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 3 hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 2 hw-breakpoint: CPU 3 failed to disable vector catch hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 Version Rollback Feature Disabled i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2 i2c i2c-0: Failed to register i2c client tlc59208f at 0x27 (-16) i2c i2c-0: Can't create device at 0x27 i2c i2c-0: Failed to register i2c client tlc59208f at 0x27 (-16) i2c i2c-0: Can't create device at 0x27 sps:sps is ready. bio: create slab <bio-0> at 0 SD0 VccQ: 1800 <--> 3000 mV SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb msm_bus_fabric_init_driver msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1 msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1 Neighbour init complete, with restricted-GC and GC-lock enabled 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0. msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready! msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0. msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initialized PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x40200000-0x402fffff] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0014[4] is all FFs PCI: bus0: Fast back to back transfers disabled pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 1:0x00 + 0x0014[4] is all FFs PCI: bus1: Fast back to back transfers disabled msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0028[4] is all FFs pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] msm_pcie_probe: msm_pcie_probe: RC0 is enabled in bootup Switched to clocksource arch_sys_counter NET: Registered protocol family 2 create ipmac proc TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available futex hash table entries: 1024 (order: 4, 65536 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled msgmni has been set to 990 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler noop registered io scheduler deadline registered (default) tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 tcsr 1953000.ess_tcsr: setting ess interface select = 0 tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled msm_serial_hsl_probe: detected port #0 (ttyMSM0) msm_serial_hsl_probe: Bus scaling is disabled 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM msm_hsl_console_setup: console setup on port #0 console [ttyMSM0] enabled msm_serial_hsl_init: driver initialized uart_tx_gpio is not available uart_rx_gpio is not available uart_cts_gpio is not available uart_rfr_gpio is not available Wakeup irq not specified. BLSP UART: Bus scaling is disabled. sps: BAM device 0x07884000 is not registered yet. sps:BAM 0x07884000 is registered. 78b0000.uart: ttyQHS0 at MMIO 0x78b0000 (irq = 140, base_baud = 460800) is a MSM HS UART qca_serial_hs module loaded sps:BAM 0x07884000 (va:0xe0b40000) enabled: ver:0x19, number of pipes:12 m25p80 spi0.0: Failed to find sector-size libphy: ipq40xx_mdio: probed ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered dwc3 8a00000.dwc3: no usb2 phy configured platform 8a00000.dwc3: Driver dwc3 requests probe deferral dwc3 6000000.dwc3: no usb2 phy configured platform 6000000.dwc3: Driver dwc3 requests probe deferral ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-platform: EHCI generic platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-platform: OHCI generic platform driver usbcore: registered new interface driver usb-storage i2c /dev entries driver tlc59208f init! tlc59208f probe Init I2c register 27 i2c-core: driver [tlc59208f] using legacy suspend method i2c-core: driver [tlc59208f] using legacy resume method debug defined config_mmc_test in mmc_register_driver debug defined config_mmc_test in mmc_register_driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper sdhci_msm 7824900.sdhci: Got SD LDO GPIO #33 sdhci_msm 7824900.sdhci: Got CD GPIO #22. mmc0: no vmmc regulator found mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (7920 buckets, 31680 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered 8021q: 802.1Q VLAN Support v1.8 Registering SWP/SWPB emulation handler regulator-dummy: disabling mmc0: BKOPS_EN bit is not set mmc0: new HS200 MMC card at address 0001 mmcblk mmc0:0001: Card claimed for testing. debug mmc_bus_probe mmcblk0: mmc0:0001 M62704 3.53 GiB mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB mmc0: Starting tests of card mmc0:0001... mmc0: Test case 4. ART read (with data verification and return)... mmc_art_verify_read: the board_data is 140601 mmc0: Result: OK mmc0: Tests completed. mmc_dni_art_read_boot_part: rootfs part is #01 read_boot_part_from_art: the rootfs part num is #01 ART part: device [179:20] mmcblk0p20 set to be root filesystem #: vol name is 0:SBL1, start is 0x22, size is 0x400, ssz is 0x1 #: vol name is 0:BOOTCONFIG, start is 0x422, size is 0x400, ssz is 0x1 #: vol name is 0:QSEE, start is 0x822, size is 0x400, ssz is 0x1 #: vol name is 0:QSEE_1, start is 0xc22, size is 0x400, ssz is 0x1 #: vol name is 0:CDT, start is 0x1022, size is 0x200, ssz is 0x1 #: vol name is 0:CDT_1, start is 0x1222, size is 0x200, ssz is 0x1 #: vol name is 0:BOOTCONFIG1, start is 0x1422, size is 0x400, ssz is 0x1 #: vol name is 0:APPSBLENV, start is 0x1822, size is 0x200, ssz is 0x1 #: vol name is 0:APPSBL, start is 0x1a22, size is 0x800, ssz is 0x1 #: vol name is 0:APPSBL_1, start is 0x2222, size is 0x800, ssz is 0x1 #: vol name is 0:ART, start is 0x2a22, size is 0x200, ssz is 0x1 #: vol name is ARTMTD, start is 0x2c22, size is 0x200, ssz is 0x1 #: vol name is language, start is 0x2e22, size is 0x1000, ssz is 0x1 #: vol name is config, start is 0x3e22, size is 0x200, ssz is 0x1 #: vol name is pot, start is 0x4022, size is 0x200, ssz is 0x1 #: vol name is traffic_meter, start is 0x4222, size is 0x200, ssz is 0x1 #: vol name is pot_bak, start is 0x4422, size is 0x200, ssz is 0x1 #: vol name is traffic_meter.bak, start is 0x4622, size is 0x200, ssz is 0x1 #: vol name is kernel, start is 0x4822, size is 0x1f00, ssz is 0x1 #: vol name is rootfs, start is 0x6722, size is 0xf500, ssz is 0x1 #: vol name is firmware, start is 0x4822, size is 0x11400, ssz is 0x1 #: vol name is mtdoops, start is 0x15c22, size is 0x200, ssz is 0x1 #: vol name is cert, start is 0x15e22, size is 0x80, ssz is 0x1 #: vol name is kernel-2, start is 0x15ea2, size is 0x1f00, ssz is 0x1 #: vol name is rootfs-2, start is 0x17da2, size is 0xf500, ssz is 0x1 #: vol name is firmware-2, start is 0x15ea2, size is 0x11400, ssz is 0x1 #: vol name is device_table, start is 0x272a2, size is 0x2800, ssz is 0x1 #: vol name is cp_file, start is 0x29aa2, size is 0x8800, ssz is 0x1 #: vol name is streamboost, start is 0x322a2, size is 0x19000, ssz is 0x1 #: vol name is forceshield, start is 0x4b2a2, size is 0xf000, ssz is 0x1 #: vol name is arlo, start is 0x5a2a2, size is 0x2800, ssz is 0x1 #: vol name is insight, start is 0x622a2, size is 0x4000, ssz is 0x1 #: vol name is rae, start is 0x662a2, size is 0x1000, ssz is 0x1 #: vol name is https_cert, start is 0x672a2, size is 0x100, ssz is 0x1 #: vol name is config_backup, start is 0x673a2, size is 0x2800, ssz is 0x1 #: vol name is reserved, start is 0x69ba2, size is 0x2633ff, ssz is 0x1 mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 p34 p35 p36 mmcblk0boot1: unknown partition table mmcblk0boot0: unknown partition table xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: xHCI Host Controller usb usb1: Manufacturer: Linux 3.14.77 xhci-hcd usb usb1: SerialNumber: xhci-hcd.0.auto hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.14.77 xhci-hcd usb usb2: SerialNumber: xhci-hcd.0.auto hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000 usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.14.77 xhci-hcd usb usb3: SerialNumber: xhci-hcd.1.auto hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.14.77 xhci-hcd usb usb4: SerialNumber: xhci-hcd.1.auto hub 4-0:1.0: USB hub found hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) drivers/rtc/hctosys.c: unable to open rtc device (rtc0) clk: Not disabling unused clocks VFS: Mounted root (squashfs filesystem) readonly on device 179:20. Freeing unused kernel memory: 184K (c088c000 - c08ba000) init: Console is alive init: - watchdog - init: - preinit - random: mktemp: uninitialized urandom read (6 bytes read, 68 bits of entropy available) random: mktemp: uninitialized urandom read (6 bytes read, 68 bits of entropy available) random: mktemp: uninitialized urandom read (6 bytes read, 68 bits of entropy available) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level Before mount_root Before DNI mount_root After DNI mount_root After mount_root 377+0 records in 377+0 records out 12064 bytes (11.8KB) copied, 0.005456 seconds, 2.1MB/s 377+0 records in 377+0 records out 12064 bytes (11.8KB) copied, 0.004074 seconds, 2.8MB/s 377+0 records in 377+0 records out 12064 bytes (11.8KB) copied, 0.003964 seconds, 2.9MB/s procd: - early - procd: - watchdog - procd: - ubus - random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available) random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available) random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available) random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available) random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available) random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available) random: ubusd: uninitialized urandom read (4 bytes read, 80 bits of entropy available) procd: - init - Please press Enter to activate this console. Fri Sep 17 01:23:34 UTC 2021 Checking env partition first ... /dev/mem opened. Memory mapped at address 0xb6fbc000. Value at address 0x102D000 (0xb6fbc000): 0x4801 Written 0x4902; readback 0x4902 /dev/mem opened. Memory mapped at address 0xb6efd000. Value at address 0x102E000 (0xb6efd000): 0x4801 Written 0x4902; readback 0x49atherosgpio init LED = 64, 63,54 ,53, 57,60 02 /dev/mem opened. Memory mapped at address 0xb6fc8000. Value at address 0x103A000 (0xb6fc8000): 0x20C Written 0x4902; readback 0x4902 /dev/mem opened. Memory mapped at address 0xb6f39000. Value at address 0x103B000 (0xb6f39000): 0x208 Written 0x4902; readback 0x4902 The region number is: 0x0002 REGION: WW PIN should be a number, using fixed 12345670 WPSPIN: 12345670 sn:5826985B077C6 SN: 5826985B077C6 lan mac: 38:94:ed:d1:7a:40 wlan 2g mac: 3e:94:ed:d1:7a:40 wan mac: 38:94:ed:d1:7a:41 wlan5g mac: 38:94:ed:d1:7a:42 wlan2nd5g mac: 38:94:ed:d1:7a:43 bt mac: 38:94:ed:d1:7a:44 hw_revision: Loading data from " config_dev " ... datalib: header->magic is 0x0, not same as 0x20170328... Fail! Resetting to default values ... The data center is Running ... Saving Data... random: nonblocking pool is initialized Done! Saving Data... Done! Saving Data... Done! Generating Rules... Done! QCE50: __qce_init_clk: Unable to get CE core src clk, set to NULL qcrypto 8e20000.qcrypto: Qualcomm Crypto 5.3.1 device found @0x8e20000 qcrypto 8e20000.qcrypto: CE device = 0x0 , IO base, CE = 0xe11c0000 , Consumer (IN) PIPE 2, Producer (OUT) PIPE 3 IO base BAM = 0x (null) BAM IRQ 239 Engines Availability = 0x2010453 sps:BAM 0x08e04000 is registered. sps:BAM 0x08e04000 (va:0xe1400000) enabled: ver:0x27, number of pipes:4 QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000008e04000 irq 239 bus_scale_table is NULL qcrypto 8e20000.qcrypto: qcrypto-ecb-aes qcrypto 8e20000.qcrypto: qcrypto-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-ctr-aes qcrypto 8e20000.qcrypto: qcrypto-ecb-des qcrypto 8e20000.qcrypto: qcrypto-cbc-des qcrypto 8e20000.qcrypto: qcrypto-ecb-3des qcrypto 8e20000.qcrypto: qcrypto-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-xts-aes qcrypto 8e20000.qcrypto: qcrypto-sha1 qcrypto 8e20000.qcrypto: qcrypto-sha256 qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-hmac-sha1 qcrypto 8e20000.qcrypto: qcrypto-hmac-sha256 qcrypto 8e20000.qcrypto: qcrypto-aes-ccm qcrypto 8e20000.qcrypto: qcrypto-rfc4309-aes-ccm qcrypto: FIPS140-2 Known Answer Tests: Skipped clbr: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint client bridge loaded device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com NTFS driver 2.1.30 [Flags: R/O MODULE]. PPP generic driver version 2.4.2 ess-switch DT exist! switchreg_base_addr: 0xc000000 switchreg_size: 0x80000 switch_access_mode: local bus wan bmp:0x20 ess-psgmii DT exist! mac mode=0 current mac mode = 0 current dts led_source_num is 5 mdio DT exist! ssdk_plat_init start enable ess clk reset ok in probe! PHY ID is 0x4dd0b1 qca probe malibu phy driver succeeded! Dakota Chip version 0x1401 qca-ssdk module init succeeded! tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ********************************************************** * Driver :NSS GMAC Driver for RTL v(3.72a) * Version :1.0 * Copyright :Copyright (c) 2013-2016 The Linux Foundation. All rights reserved. ********************************************************** mdio bus 'mdio-gpio.0' get FAIL. l2tp_core: L2TP core driver, V2.0 l2tp_netlink: L2TP netlink interface qca-nss-drv.ko is loaded for symbol link dni-qos module init. gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) QCA Hy-Fi multicast installation successfully ip6_tables: (C) 2000-2006 Netfilter Core Team nf_conntrack_rtsp v0.6.21 loading nf_nat_rtsp v0.6.21 loading XHTTP netlink: create netlink OK. ip_set: protocol 6 NET: Registered protocol family 24 ECM init ECM database jhash random seed: 0xeca7e677 ECM init complete PPTP driver version 0.8.5 u32 classifier Performance counters on input device check on Actions configured Mirror/redirect action on fuse init (API version 7.22) Loading DNI-ENET driver Ebtables v2.0 registered l2tp_ppp: PPPoL2TP kernel driver, V2.0 ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 . = switch init . cfg02aa45 Saving Data... Done! 62 QoS default rules are Loaded! Saving Data... Done! Saving Data... Done! ssid:ORBI08 passphrase:deeppotato215 ssid:NETGEAR_ORBI_hidden10 passphrase:Gs3SjOsBA3tSrZL5yNHSVjJz8wp4JvUSVve3EWONuZnWwPYvR2Z4oDHftQmZJEb Saving Data... Done! Saving Data... Done! Saving Data... Done! Saving Data... Done! Saving Data... Done! Saving Data... hyfi_netlink_receive:66:Device not found: br0 hyd: ERROR: Bridge is not attached; start hyfi-bridging first Done! exception condition Saving Data... Done! Saving Data... Done! Saving Data... Done! Saving Data... Done! . = network init SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. device eth1 entered promiscuous mode init.enet: Default LAN MAC is : 38:94:ed:d1:7a:40 . Successfully initialized wpa_supplicant have reset factory,dal partition will be will re-format /dev/mmcblk0p31 contains a ext4 file system last mounted on /tmp/dal on Fri Apr 19 14:28:53 2024 Discarding device blocks: 1024/5120 done Creating filesystem with 5120 1k blocks and 1280 inodes Allocating group tables: 0/1 done Writing inode tables: 0/1 done Creating journal (1024 blocks): done Writing superblocks and filesystem accounting information: 0/1 done EXT4-fs (mmcblk0p31): mounted filesystem with ordered data mode. Opts: (null) mount dal partition successful. Saving Data... Done! D2D stopped running boot ************* start time = 01:24:02 end time = 01:24:05 start_service ************* switch init SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. 043712:(277): add subscription Dilsignature (0) 043712:(277): Registering ntf 043712:(277): (De)registering complete 043712:(277): add subscription General (0) 043713:(277): add subscription DILGeneral (0) EXT4-fs (mmcblk0p34): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (mmcblk0p34): couldn't mount as ext2 due to feature incompatibilities EXT4-fs (mmcblk0p34): warning: mounting unchecked fs, running e2fsck is recommended EXT4-fs (mmcblk0p34): mounted filesystem without journal. Opts: (null) opmode = normal ********************* have done something about plug off *********************** device eth1 left promiscuous mode br0: port 1(eth1) entered disabled state device eth1 entered promiscuous mode device eth0 entered promiscuous mode SSDK Init OK! operate done. SSDK Init OK! Illegal parameter(s) SSDK Init OK! operate done. IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready net.bridge.bridge-nf-call-custom = 0 hyfi_netlink_receive:108:hyfi: Not attached to bridge br0 Error running command IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready net.bridge.bridge-nf-call-custom = 1 Deleting static route ... Done! Adding static route ... Done! udhcp server (v0.9.8) started SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. br0: port 1(eth1) entered forwarding state br0: port 1(eth1) entered forwarding state IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready IPv6: ADDRCONF(NETDEV_UP): brwan: link is not ready hyd: starting daemon [wlan]===time:Fri Sep 17 01:24:12 UTC 2021 command:wlan countrycode============== [wlan]===time:Fri Sep 17 01:24:14 UTC 2021 command:wlan updateconf boot============== [wlan]=========time:Fri Sep 17 01:24:14 UTC 2021 wlan updateconf start====== SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. EXT4-fs (mmcblk0p27): recovery complete EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts: (null) Run BASE_BOARD net-scan config...The attached devices demo is Running ... Support ssdk switch mac table check function. Saving Data... Done! net-scan backgroud start scan... [net-scan] start scan devices... 056533:(283): add subscription DILGeneral (0) 056534:(283): Registering ntf 056534:(283): (De)registering complete 056535:(284): add subscription FeatureCfg (0) 056535:(284): Registering ntf 056535:(284): (De)registering complete 056536:(285): add subscription Dilsignature (0) 056536:(285): Registering ntf 056537:(285): (De)registering complete IPv6: ADDRCONF(NETDEV_UP): brwan: link is not ready hyd: updateconf not ready for hyd [wlan]=========time:Fri Sep 17 01:24:23 UTC 2021 wlan updateconf end====== QCA post_updateconf_qcawifi udhcp client (v0.9.8) started no 6RD parameters available, so unset 6rd related config [net-scan]receive SIG10.. [fing-devices]receive SIG10.. EXT4-fs (mmcblk0p32): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (mmcblk0p32): couldn't mount as ext2 due to feature incompatibilities DIL Total device num=0 EXT4-fs (mmcblk0p32): recovery complete EXT4-fs (mmcblk0p32): mounted filesystem with ordered data mode. Opts: (null) time zone index is : 0 Run NTP Client with setting: pri:time-g.netgear.com sec:time-h.netgear.com Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 [wlan]===time:Fri Sep 17 01:24:26 UTC 2021 command:wlan down============== [wlan]=========time:Fri Sep 17 01:24:26 UTC 2021 wlan down start================== will set soap sync psk:0b64c362af829d5895a4e8bbf21979a681ca52a01104fc71615dbae19c7ba85c Saving Data... Reading configuration from file /tmp/etc/miniupnpd.conf Sep 17 01:24:27 miniupnpd[11960]: listening on 192.168.1.1:5555 Done! Saving Data... AUTO FW CHECK: power cycle Done! Init wifison script Not get NTP time temporarily, save uptime instead Invalid IP Address:www.netgear.com echo '' > /tmp/ping_result echo "Unknown host" > /tmp/ping_result_error [FW UPGRADE][2021-09-17 01:24:28]:ping netgear_domain failed!!! Saving Data... Done! week_day == 3 count time:0 qcawifi disable radio wifi0 qcawifi disable radio wifi1 qcawifi disable radio wifi2 Saving Data... Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 Done! [wlan]===time:Fri Sep 17 01:24:30 UTC 2021 command:wlan stainfo============== Saving Data... Done! Saving Data... Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 Done! [wlan]=========time:Fri Sep 17 01:24:32 UTC 2021 wlan down end================== [wlan]=========time:Fri Sep 17 01:24:32 UTC 2021 wlan post down ================== net.bridge.bridge-nf-call-custom = 1 Saving Data... Done! net.bridge.bridge-nf-call-custom = 1 128+0 records in 128+0 records out 65536 bytes (64.0KB) copied, 0.002816 seconds, 22.2MB/s cert.info tar: cert.info: time stamp 2025-09-22 13:11:41 is 126704827.024186224 s in the future ca.crt tar: ca.crt: time stamp 2025-09-22 13:11:38 is 126704824.023655079 s in the future dh1024.pem tar: dh1024.pem: time stamp 2025-09-22 13:11:39 is 126704825.023340474 s in the future client.crt tar: client.crt: time stamp 2025-09-22 13:11:41 is 126704827.023024329 s in the future client.key tar: client.key: time stamp 2025-09-22 13:11:41 is 126704827.022752474 s in the future server.crt tar: server.crt: time stamp 2025-09-22 13:11:39 is 126704825.022455245 s in the future server.key tar: server.key: time stamp 2025-09-22 13:11:39 is 126704825.02219312 s in the future Changing password for root New password: Bad password: too weak Password for root changed by root Changing password for admin New password: Bad password: too weak Password for admin changed by root Starting Firewall... xt_CT: netfilter: NOTRACK target is deprecated, use CT instead or upgrade iptables Done! traffic_meter start : . $Shutting down igmpproxy: New soap mechanism is on ! The soap_agent demo is Running ... [soap_checkfw]expect_time=17400 [soap_checkfw]expect_time_hm=4:50 [soap_checkfw]expect_time=17400, current_time=5075, diff_time=12325 [soap_checkfw]expect_time_hm=4:50 [soap_checkfw]curl_expect_time_hm=6:36 EXT4-fs (mmcblk0p28): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (mmcblk0p28): couldn't mount as ext2 due to feature incompatibilities EXT4-fs (mmcblk0p28): recovery complete EXT4-fs (mmcblk0p28): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (mmcblk0p35): recovery complete EXT4-fs (mmcblk0p35): mounted filesystem with ordered data mode. Opts: (null) hyd: some interface(s) are not ready. hyd: ERROR: Private network interface checking failed Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 net.ipv4.neigh.default.gc_reap_limit = 100 restart klogd process [Orbi]***boot done*** [wifi-listener] Starting daemon [ arlo ] arlo list not found [wlan]===time:Fri Sep 17 01:24:39 UTC 2021 command:wlan up============== [wlan]=========time:Fri Sep 17 01:24:39 UTC 2021 wlan up start================== insight-cli (14967): undefined instruction: pc=b6b98f48 Code: f2000c40 e12fff1e f3000c40 e12fff1e (f2a00e00) insight-cli (14967): undefined instruction: pc=b6b98f30 Code: f2200150 e12fff1e ec510f1e e12fff1e (f3b00300) insight-cli (14967): undefined instruction: pc=b6b98f38 Code: ec510f1e e12fff1e f3b00300 e12fff1e (f2000c40) insight-cli (14967): undefined instruction: pc=b6b98f40 Code: f3b00300 e12fff1e f2000c40 e12fff1e (f3000c40) insight-cli (14967): undefined instruction: pc=b6b98f28 Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e) Saving Data... Done! qcawifi: enable radio wifi0 __mm_init_module ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_spectral: Version 2.0.0 Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved xagent (15423): undefined instruction: pc=b6c84f48 Code: f2000c40 e12fff1e f3000c40 e12fff1e (f2a00e00) xagent (15423): undefined instruction: pc=b6c84f30 Code: f2200150 e12fff1e ec510f1e e12fff1e (f3b00300) xagent (15423): undefined instruction: pc=b6c84f38 Code: ec510f1e e12fff1e f3b00300 e12fff1e (f2000c40) xagent (15423): undefined instruction: pc=b6c84f40 Code: f3b00300 e12fff1e f2000c40 e12fff1e (f3000c40) ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D) xagent (15423): undefined instruction: pc=b6c84f28 ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_tx99: Version 2.0 Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e) ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_da_pci: (Atheros/multi-bss) insight-brokerd (15457): undefined instruction: pc=b6c8df48 *********** IPQ4019 *************Wifi0 CPU frequency 250000000 Code: f2000c40 e12fff1e f3000c40 e12fff1e (f2a00e00) hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: E insight-brokerd (15457): undefined instruction: pc=b6c8df30 hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn da6c04c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type b __ol_ath_attach: dev name wifi0 ol_ath_attach interface_id 0 Code: f2200150 e12fff1e ec510f1e e12fff1e (f3b00300) ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xb, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3799] Get Caldata for wifi0. qdf_fs_read[59], Open File /tmp/wifi0.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 3107file size:12064qc98xx_verify_checksum: flash checksum passed: 0x1d89 ol_transfer_bin_file 3875: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 0, Download data len 4680 insight-brokerd (15457): undefined instruction: pc=b6c8df38 Code: ec510f1e e12fff1e f3b00300 e12fff1e (f2000c40) First OTP send param 8000 insight-brokerd (15457): undefined instruction: pc=b6c8df40 ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660 ol_ath_download_firmware:##Board Id 20 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi0: Selecting board data file name boardData_1_0_IPQ4019_DK04_2G.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_2G.bin ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 0, Download data len 4680 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1610612717 Code: f3b00300 e12fff1e f2000c40 e12fff1e (f3000c40) insight-brokerd (15457): undefined instruction: pc=b6c8df28 Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e) ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:101685 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 160459 Target address 417c40 scn=da6c04c0 target_write_addr=417c40 seg_info=deb95410 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin whc (repacd): starting WHC auto-configuration whc (repacd): Managed network: 0 whc (repacd): Device type: CAP ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 1, Download data len 368932 insight-configd (15442): undefined instruction: pc=b6cabf48 Code: f2000c40 e12fff1e f3000c40 e12fff1e (f2a00e00) insight-configd (15442): undefined instruction: pc=b6cabf30 Code: f2200150 e12fff1e ec510f1e e12fff1e (f3b00300) insight-configd (15442): undefined instruction: pc=b6cabf38 Code: ec510f1e e12fff1e f3b00300 e12fff1e (f2000c40) insight-configd (15442): undefined instruction: pc=b6cabf40 Code: f3b00300 e12fff1e f2000c40 e12fff1e (f3000c40) insight-configd (15442): undefined instruction: pc=b6cabf28 Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e) The abbreviation of English is Eng! Didn't find the language table we need! ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle dec52000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :db698000-htc_create: (0xdcf67800) htc_wmi_init() HT Create . dcf67800 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xdb69c578hif_completion_thread_startup: pipe_num:3 pipe_info:0xdb69c650hif_completion_thread_startup: pipe_num:4 pipe_info:0xdb69c698 -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev d9440000 hrtimer d9444888 htt_alloc_peer_map_mem : Alloc Success : host q vaddr de324000 paddr 9e324000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d90c0000 Firmware_Build_Number:14 FW wireless modes: 0x680c num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa btcoex_support 1, wlan_prio_gpio 52, coex_gpio_pin 0 0 0 wmi_service_coex_gpio 1, wmi_service_4_wire_coex_support 1, coex_version 2 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 52 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 SOAP Len:400 Action:DeviceInfo Method:GetInfo IP:127.0.0.1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, [DeviceInfo][GetInfo] soap_auth MAC[], have_auth = 0 [127.0.0idx 6 req 5 num_units 0 num_unit_info 2 unit size 2044 actual units 531 .1] AUTH = -1 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2044, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x9b530000 chunk 1 len 54272 requested , ptr 0x99120000 chunk 2 len 217088 requested , ptr 0x99140000 chunk 3 len 395064 requested , ptr 0x99180000 chunk 4 len 107520 requested , ptr 0x99200000 chunk 5 len 6144 requested , ptr 0x9b68e000 chunk 6 len 1085364 requested , ptr 0x98c00000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 0 ol_ath_attach() connect HTC. bypasswmi : 0 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: 2884: Netlink socket created:de9d7800 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_attach: called; ptr=d917998c, radar_info=da4e1c20 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[1] ..ptr:bfb37e48 ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =dcf0be00 ic->ic_wrap_com=dcf0be00 &wrap_com->wc_devt=dcf0be00 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_ahb_probe num_radios=0, wifi_radios[0].sc = da6c04c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr *********** IPQ4019 *************Wifi1 CPU frequency 250000000 hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn d8d404c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type b __ol_ath_attach: dev name wifi1 ol_ath_attach interface_id 1 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xb, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3799] Get Caldata for wifi1. qdf_fs_read[59], Open File /tmp/wifi1.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 736file size:12064qc98xx_verify_checksum: flash checksum passed: 0x9331 ol_transfer_bin_file 3875: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 0, Download data len 4680 First OTP send param 8000 ol_ath_download_firmware :First OTP download and Execute is good address:0x5400 return param 4660 ol_ath_download_firmware:##Board Id 21 , CHIP Id 0 DHCPv6 client is not running! Return ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi1: Selecting board data file name boardData_1_0_IPQ4019_DK04_5G.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_5G.bin ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 0, Download data len 4680 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:101685 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 160459 Target address 417c40 scn=d8d404c0 target_write_addr=417c40 seg_info=db549410 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 1, Download data len 368932 DHCPv6 client is not running! Return Stopping Firewall... IPv6 Done! the ipv6 wan type is disable ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle da782000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :d8dc8000-htc_create: (0xdcf66000) htc_wmi_init() HT Create . dcf66000 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xd8dcc578hif_completion_thread_startup: pipe_num:3 pipe_info:0xd8dcc650hif_completion_thread_startup: pipe_num:4 pipe_info:0xd8dcc698 -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev d85f0000 hrtimer d85f4888 htt_alloc_peer_map_mem : Alloc Success : host q vaddr d9304000 paddr 99304000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d8260000 Firmware_Build_Number:14 FW wireless modes: 0x1f9001 num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, idx 6 req 5 num_units 0 num_unit_info 2 unit size 2044 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2044, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x992bc000 chunk 1 len 54272 requested , ptr 0x982c0000 chunk 2 len 217088 requested , ptr 0x98300000 chunk 3 len 395064 requested , ptr 0x98380000 chunk 4 len 107520 requested , ptr 0x982e0000 chunk 5 len 6144 requested , ptr 0x9b430000 chunk 6 len 1085364 requested , ptr 0x97c00000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 SOAP Len:400 Action:DeviceConfig Method:GetInfo IP:127.0.0.1ersion = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 [DeviceConfig][GetInfo] soap_auth MAC[], have_auth = 0 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1 [127.0.0.1] AUTH = -1 ol_ath_attach() connect HTC. bypasswmi : 0 ol_ath_attach: low_5ghz: 5150 high_5gh: 5330 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === SOAP Len:400 Action:DeviceInfo Method:GetInfo IP:127.0.0.1 [DDNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === eviceInfo][GetInfo] soap_auth MAC[], have_auth = 0 [127.0.0.1DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === ] AUTH = -1 DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Add VHT80 channel: 5690 Add VHT80 channel: 5775 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=58 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: Offload using existing sock de9d7800 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_attach: called; ptr=d7d8998c, radar_info=da4e1c20 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[2] ..ptr:bfb37e48 ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =db56f800 ic->ic_wrap_com=db56f800 &wrap_com->wc_devt=db56f800 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_ahb_probe num_radios=1, wifi_radios[1].sc = d8d404c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr ath_ol_pci: (Atheros/multi-bss) hif_pci_enable_bus: con_mode = 0x0, device_id = 0x46PCI: enabling device 0000:00:00.0 (0144 -> 0147) PCI: enabling device 0000:01:00.0 (0140 -> 0142) hif_pci_enable_bus: hif_enable_pci done *********** QCA9984 *************hif_pci_enable_bus: hif_type = 0xc, target_type = 0xahif_pci_enable_bus: hif_pci_probe_tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW signal, retries = 0hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_set_hia_extnd: E chip_id 0xa chip_revision 0x0 CLOCK PLL skipped hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL hif_set_hia_extnd: targ_clk is not provided, skipping pre-configuring PLL hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn d7e004c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type a __ol_ath_attach: dev name wifi2 ol_ath_attach interface_id 2 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xa, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 Switching to Tx Mode-1 Threshold 280 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3799] Get Caldata for wifi2. qdf_fs_read[59], Open File /tmp/wifi2.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 3110file size:12064qc98xx_verify_checksum: flash checksum passed: 0xcc7d ol_transfer_bin_file 3875: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 0, Download data len 9024 First OTP send param 8000 SOAP Len:400 Action:WLANConfiguration Method:GetInfo IP:127.0.0.1 [WLANConfiguration][GetInfo] soap_auth MAC[], have_auth = 0 [127.0.0.1] AUTH = -1 SOAP Len:400 Action:WLANConfiguration Method:GetWPASecurityKeys IP:127.0.0.1 [WLANConfiguration][GetWPASecurityKeys] soap_auth MAC[], have_auth = 0 [127.0.0.1] AUTH = -1 SOAP Len:400 Action:WLANConfiguration Method:GetWEPSecurityKeys IP:127.0.0.1 [WLANConfiguration][GetWEPSecurityKeys] soap_auth MAC[], have_auth = 0 [127.0.0.1] AUTH = -1 ol_ath_download_firmware :First OTP download and Execute is good address:0x1800 return param 4660 ol_ath_download_firmware:##Board Id 6 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9984/hw.1/boardData_QCA9984_CUS239_high_band_5G_v1_006.bin ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 Switching to Tx Mode-1 Threshold 280 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 0, Download data len 9024 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:28372 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 233772 Target address 4233c8 scn=d7e004c0 target_write_addr=4233c8 seg_info=db549710 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=QCA9984/hw.1/athwlan.bin swap_filename=/lib/firmware/QCA9984/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: QCA9984/hw.1/athwlan.bin ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3680: downloading file 1, Download data len 379644 ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle d7eb0000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :d9290000-htc_create: (0xde2e4800) htc_wmi_init() HT Create . de2e4800 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xd9294578hif_completion_thread_startup: pipe_num:3 pipe_info:0xd9294650hif_completion_thread_startup: pipe_num:4 pipe_info:0xd9294698 -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev d7bc0000 hrtimer d7bc4888 htt_alloc_peer_map_mem : Alloc Success : host q vaddr d7bca000 paddr 97bca000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d7040000 Firmware_Build_Number:14 FW wireless modes: 0x7f9001 num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339b79fa vht_supp_mcs:0x0000ffaa wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 2216 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 2216, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 12288 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 12288, idx 6 req 5 num_units 0 num_unit_info 2 unit size 1980 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 1980, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x97e8c000 chunk 1 len 54272 requested , ptr 0x970a0000 chunk 2 len 217088 requested , ptr 0x970c0000 chunk 3 len 1176696 requested , ptr 0x97200000 chunk 4 len 107520 requested , ptr 0x97340000 chunk 5 len 12288 requested , ptr 0x9b630000 chunk 6 len 1051380 requested , ptr 0x96c00000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 2 ol_ath_attach() connect HTC. bypasswmi : 0 ol_ath_attach: low_5ghz: 5490 high_5gh: 5850 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Add VHT80 channel: 5690 Add VHT80 channel: 5775 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === Skipping VHT80 channel 5825 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === freq=106 freq=122 freq=138 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: Offload using existing sock de9d7800 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_if_dfs_attach: called; ptr=d6d0998c, radar_info=da4e1c00 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[3] ..ptr:bfb37e48 ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =d7d9fa00 ic->ic_wrap_com=d7d9fa00 &wrap_com->wc_devt=d7d9fa00 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_pci_probe num_radios=2, wifi_radios[2].sc = d7e004c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback __sa_init_module No Direct-Attach chipsets found. Removing athdebug proc file ath_dev: driver unloaded ath_tx99: driver unloaded ath_rate_atheros: driver unloaded ath_hal: driver unloaded isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 wlan_vap_create : enter. devhandle=0xda6c04c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 3e:94:ed:d1:7a:40: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xda6c04c0, vap=0xda4b0000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling TSO bit for the vap ath0 features 4000 Enabling LRO bit for the vap ath0 features 4000 VAP device ath0 created osifp: (de99ecc0) os_if: (da4b0000) siwfreq Set freq vap 0 stop send + da4b0000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17021 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 0 stop send -da4b0000 Set wait done --da4b0000 ME Pool succesfully initialized vaddr - d6dc0000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-0(ath0):set SIOC80211NWID, 2 characters DES SSID SET=on vap-0(ath0):set SIOC80211NWID, 6 characters DES SSID SET=ORBI08 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath0 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< Sending SCAN START cmd br0: port 2(ath0) entered forwarding state br0: port 2(ath0) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath0 OK ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17153 Comm:iwpriv :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd wlan_vap_create : enter. devhandle=0xda6c04c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 1 Type = 1, Subtype = 0 VAP Addr = 42:94:ed:d1:7a:40: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xda6c04c0, vap=0xdb5a0000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath01 features 4000 Enabling SG bit for the vap ath01 features 4000 Enabling SG bit for the vap ath01 features 4000 Enabling TSO bit for the vap ath01 features 4000 Enabling LRO bit for the vap ath01 features 4000 VAP device ath01 created osifp: (db5424c0) os_if: (db5a0000) siwfreq Set freq vap 0 stop send + da4b0000 ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17164 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 0 stop send -da4b0000 Set wait done --da4b0000 Set freq vap 1 stop send + db5a0000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17164 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 1 stop send -db5a0000 Set wait done --db5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17164 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 Sending SCAN START cmd ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17178 Comm:iwpriv :: PPID:15359 Comm:wlan <=< Switching to Tx Mode-1 Threshold 280 Sending SCAN START cmd ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17185 Comm:iwpriv :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd vap-1(ath01):set SIOC80211NWID, 2 characters DES SSID SET=on vap-1(ath01):set SIOC80211NWID, 21 characters DES SSID SET=NETGEAR_ORBI_hidden10 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 00146c Privatesu bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 capibility_data : 0408010000000000 -------------------su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 --------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 device ath01 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath01 DEVICE IS DOWN ifname=ath01 repacd: checking backhaul_ap interface --> network:0 - iface:ath0 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath01 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:1 repacd: checking backhaul_ap interface --> network:0 - iface:ath1 - disabled:0 - mode:ap - device:wifi1 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath02 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath11 - disabled:0 - mode:ap - device:wifi1 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath03 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath12 - disabled:0 - mode:ap - device:wifi1 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath04 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:0 repacd: checkingOtherband BSSID 0:0:0:0:0:0 backhaul_ap interface --> network:0 - iface:ath13 - disabled:0osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 - mode:ap - device:wifi1 - backhaul_ap:0 repacd: checking backOrbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : haul_ap interface --> network:0 - iface:ath2 - disabled:0 - modOrbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< e:ap - device:wifi2 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath21 - disabled:0 - mode:ap - device:wifi2 - backhaul_ap:1 repacd: checking backhaul_ap interface --> network:0 - iface:ath22 - disabled:0 - mode:ap - device:wifi2 - backhaul_ap:0 repacd: checking backhaul_ap interfacbr0: port 3(ath01) entered forwarding state br0: port 3(ath01) entered forwarding state e --> network:0 - iface:ath23 - disabled:0 - mode:ap - device:w8021q: adding VLAN 0 to HW filter on device ath01 ifi2 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath24 - disabled:0 - mode:ap - device:wifi2 - backhaul_ap:0 OK osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17344 Comm:iwpriv :: PPID:15359 Comm:wlan <=< wlan_vap_create : enter. devhandle=0xda6c04c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 2 Type = 1, Subtype = 0 VAP Addr = 46:94:ed:d1:7a:40: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xda6c04c0, vap=0xda650000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath02 features 4000 Enabling SG bit for the vap ath02 features 4000 Enabling SG bit for the vap ath02 features 4000 Enabling TSO bit for the vap ath02 features 4000 Enabling LRO bit for the vap ath02 features 4000 VAP device ath02 created osifp: (de99dcc0) os_if: (da650000) siwfreq Set freq vap 0 stop send + da4b0000 ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17375 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 0 stop send -da4b0000 Set wait done --da4b0000 Set freq vap 1 stop send + db5a0000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17375 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 1 stop send -db5a0000 Set wait done --db5a0000 Set freq vap 2 stop send + da650000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17375 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 2 stop send -da650000 Set wait done --da650000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17375 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17375 Comm:iwconfig :: PPID:15359 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17410 Comm:iwpriv :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17410 Comm:iwpriv :: PPID:15359 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17442 Comm:iwpriv :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17442 Comm:iwpriv :: PPID:15359 Comm:wlan <=< hyd: boot daemon WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-2(ath02):set SIOC80211NWID, 2 characters DES SSID SET=on vap-2(ath02):set SIOC80211NWID, 12 characters DES SSID SET=ORBI08-GUEST ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath02 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath02 DEVICE IS DOWN ifname=ath02 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda650000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< br0: port 4(ath02) entered forwarding state br0: port 4(ath02) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath02 OK osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xda650000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17584 Comm:ifconfig :: PPID:15359 Comm:wlan <=< br0: port 4(ath02) entered disabled state wlan_vap_create : enter. devhandle=0xda6c04c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 3 Type = 1, Subtype = 0 VAP Addr = 4a:94:ed:d1:7a:40: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xda6c04c0, vap=0xda660000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath03 features 4000 Enabling SG bit for the vap ath03 features 4000 Enabling SG bit for the vap ath03 features 4000 Enabling TSO bit for the vap ath03 features 4000 Enabling LRO bit for the vap ath03 features 4000 VAP device ath03 created osifp: (de9d9cc0) os_if: (da660000) siwfreq Set freq vap 0 stop send + da4b0000 ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17607 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 0 stop send -da4b0000 Set wait done --da4b0000 Set freq vap 1 stop send + db5a0000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17607 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 1 stop send -db5a0000 Set wait done --db5a0000 Set freq vap 2 stop send + da650000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17607 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 2 stop send -da650000 Set wait done --da650000 Set freq vap 3 stop send + da660000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17607 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 3 stop send -da660000 Set wait done --da660000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17607 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17607 Comm:iwconfig :: PPID:15359 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17625 Comm:iwpriv :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17625 Comm:iwpriv :: PPID:15359 Comm:wlan <=< WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-3(ath03):set SIOC80211NWID, 2 characters DES SSID SET=on vap-3(ath03):set SIOC80211NWID, 8 characters DES SSID SET=ORBI08-2 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath03 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath03 DEVICE IS DOWN ifname=ath03 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda660000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< br0: port 5(ath03) entered forwarding state br0: port 5(ath03) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath03 OK osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xda660000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17719 Comm:ifconfig :: PPID:15359 Comm:wlan <=< br0: port 5(ath03) entered disabled state wlan_vap_create : enter. devhandle=0xda6c04c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 4 Type = 1, Subtype = 0 VAP Addr = 4e:94:ed:d1:7a:40: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xda6c04c0, vap=0xd6d80000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath04 features 4000 Enabling SG bit for the vap ath04 features 4000 Enabling SG bit for the vap ath04 features 4000 Enabling TSO bit for the vap ath04 features 4000 Enabling LRO bit for the vap ath04 features 4000 VAP device ath04 created osifp: (de998cc0) os_if: (d6d80000) siwfreq Set freq vap 0 stop send + da4b0000 ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17738 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 0 stop send -da4b0000 Set wait done --da4b0000 Set freq vap 1 stop send + db5a0000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17738 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 1 stop send -db5a0000 Set wait done --db5a0000 Set freq vap 2 stop send + da650000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17738 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 2 stop send -da650000 Set wait done --da650000 Set freq vap 3 stop send + da660000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17738 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 3 stop send -da660000 Set wait done --da660000 Set freq vap 4 stop send + d6d80000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17738 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Set freq vap 4 stop send -d6d80000 Set wait done --d6d80000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17738 Comm:iwconfig :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17738 Comm:iwconfig :: PPID:15359 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17755 Comm:iwpriv :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17755 Comm:iwpriv :: PPID:15359 Comm:wlan <=< WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-4(ath04):set SIOC80211NWID, 2 characters DES SSID SET=on vap-4(ath04):set SIOC80211NWID, 8 characters DES SSID SET=ORBI08-3 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath04 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath04 DEVICE IS DOWN ifname=ath04 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd6d80000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< br0: port 6(ath04) entered forwarding state br0: port 6(ath04) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath04 OK osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xd6d80000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17864 Comm:ifconfig :: PPID:15359 Comm:wlan <=< br0: port 6(ath04) entered disabled state ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xda4b0000 send_vdev_down_cmd_non_tlv for vap 0 (dec52000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17888 Comm:ifconfig :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd br0: port 2(ath0) entered disabled state osif_vap_init: Scan in progress.. Cancelling it. vap: 0xda4b0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17891 Comm:ifconfig :: PPID:15359 Comm:wlan <=< br0: port 2(ath0) entered forwarding state br0: port 2(ath0) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath0 ol_scan_unregister_event_handler: Failed to unregister evhandler=bfa81784 arg=d8d20000 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xdb5a0000 send_vdev_down_cmd_non_tlv for vap 1 (dec52000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17906 Comm:ifconfig :: PPID:15359 Comm:wlan <=< Sending SCAN START cmd br0: port 3(ath01) entered disabled state osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdb5a0000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:17912 Comm:ifconfig :: PPID:15359 Comm:wlan <=< br0: port 3(ath01) entered forwarding state br0: port 3(ath01) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath01 ath0 IEEE 802.11b ESSID:"ORBI08" ath01 IEEE 802.11b ESSID:"NETGEAR_ORBI_hidden10" ath02 IEEE 802.11b ESSID:"ORBI08-GUEST" qcawifi: enable radio wifi1 ath03 IEEE 802.11b ESSID:"ORBI08-2" ath04 IEEE 802.11b ESSID:"ORBI08-3" isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=58 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 hyd: some interface(s) are not ready. hyd: ERROR: Private network interface checking failed wlan_vap_create : enter. devhandle=0xd8d404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 38:94:ed:d1:7a:42: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd8d404c0, vap=0xd7148000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling TSO bit for the vap ath1 features 4000 Enabling LRO bit for the vap ath1 features 4000 VAP device ath1 created osifp: (de9dc4c0) os_if: (d7148000) siwfreq Set freq vap 0 stop send + d7148000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:18327 Comm:iwconfig :: PPID:18110 Comm:wlan <=< Set freq vap 0 stop send -d7148000 Set wait done --d7148000 ME Pool succesfully initialized vaddr - d73e0000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-0(ath1):set SIOC80211NWID, 2 characters DES SSID SET=on ****************Start of ping-netgear******************** vap-0(ath1):set SIOC80211NWID, 6 characters DES SSID SET=ORBI08 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath1 entered promiscuous mode Saving Data... Done! 16+0 records in 16+0 records out 261088 bytes (255.0KB) copied, 0.005322 seconds, 46.8MB/s 15+0 records in 15+0 records out 244770 bytes (239.0KB) copied, 0.005554 seconds, 42.0MB/s 1+0 records in 1+0 records out 16318 bytes (15.9KB) copied, 0.001147 seconds, 13.6MB/s mmc0: Starting tests of card mmc0:0001... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 4096+0 records in 4096+0 records out 2097152 bytes (2.0MB) copied, 0.084263 seconds, 23.7MB/s DEVICE IS DOWN ifname=ath1 DEVICE IS DOWN ifname=ath1 tar: rae_version: time stamp 2021-09-30 05:19:23 is 1137257.741024129 s in the future Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< Saving Data... OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (da782000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/3 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (da782000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 7(ath1) entered forwarding state br0: port 7(ath1) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath1 OK wlan_vap_create : enter. devhandle=0xd8d404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 1 Type = 1, Subtype = 0 VAP Addr = 3e:94:ed:d1:7a:42: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd8d404c0, vap=0xd6f18000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath11 features 4000 Enabling SG bit for the vap ath11 features 4000 Enabling SG bit for the vap ath11 features 4000 Enabling TSO bit for the vap ath11 features 4000 Enabling LRO bit for the vap ath11 features 4000 VAP device ath11 created osifp: (de9db4c0) os_if: (d6f18000) siwfreq Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:18926 Comm:iwpriv :: PPID:18110 Comm:wlan <=< Done! vap 0: drop SWBA event, since vap is not active STOPPED EVENT for vap 0 (da782000) send_vdev_down_cmd_non_tlv for vap 0 (da782000) killall: aws-iot: no process killed rm: can't remove '/var/run/aws_iot.pid': No such file or direL vap_start + VDEV START ry OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 ol_vdev_start_resp_ev for vap 0 (da782000) Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:18943 Comm:aws-iot :: PPID:18451 Comm:S99zzaws <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (da782000) __ieee80211_smart_ant_init: Smart Antenna is not supported Saving Data... WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-1(ath11):set SIOC80211NWID, 2 characters DES SSID SET=on vap-1(ath11):set SIOC80211NWID, 12 characters DES SSID SET=ORBI08-GUEST ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath11 entered promiscuous mode Done! AWS-IOT: expect time 2:24:1 ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath11 DEVICE IS DOWN ifname=ath11 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 1 (da782000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/3 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 1 (da782000) ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 8(ath11) entered forwarding state br0: port 8(ath11) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath11 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:19061 Comm:ifconfig :: PPID:18110 Comm:wlan <=< STOPPED EVENT for vap 1 (da782000) send_vdev_down_cmd_non_tlv for vap 1 (da782000) br0: port 8(ath11) entered disabled state wlan_vap_create : enter. devhandle=0xd8d404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 2 Type = 1, Subtype = 0 VAP Addr = 42:94:ed:d1:7a:42: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd8d404c0, vap=0xd71c8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath12 features 4000 Enabling SG bit for the vap ath12 features 4000 Enabling SG bit for the vap ath12 features 4000 Enabling TSO bit for the vap ath12 features 4000 Enabling LRO bit for the vap ath12 features 4000 VAP device ath12 created osifp: (d71b9cc0) os_if: (d71c8000) siwfreq Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:19091 Comm:iwpriv :: PPID:18110 Comm:wlan <=< vap 0: drop SWBA event, since vap is not active STOPPED EVENT for vap 0 (da782000) send_vdev_down_cmd_non_tlv for vap 0 (da782000) OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (da782000) Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/3 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (da782000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-2(ath12):set SIOC80211NWID, 2 characters DES SSID SET=on vap-2(ath12):set SIOC80211NWID, 8 characters DES SSID SET=ORBI08-2 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath12 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath12 DEVICE IS DOWN ifname=ath12 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 2 (da782000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/3 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 2 (da782000) ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 9(ath12) entered forwarding state br0: port 9(ath12) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath12 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:19194 Comm:ifconfig :: PPID:18110 Comm:wlan <=< STOPPED EVENT for vap 2 (da782000) send_vdev_down_cmd_non_tlv for vap 2 (da782000) br0: port 9(ath12) entered disabled state wlan_vap_create : enter. devhandle=0xd8d404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 3 Type = 1, Subtype = 0 VAP Addr = 46:94:ed:d1:7a:42: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd8d404c0, vap=0xd6f40000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath13 features 4000 Enabling SG bit for the vap ath13 features 4000 Enabling SG bit for the vap ath13 features 4000 Enabling TSO bit for the vap ath13 features 4000 Enabling LRO bit for the vap ath13 features 4000 VAP device ath13 created osifp: (d6d99cc0) os_if: (d6f40000) siwfreq Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:19225 Comm:iwpriv :: PPID:18110 Comm:wlan <=< vap 0: drop SWBA event, since vap is not active STOPPED EVENT for vap 0 (da782000) send_vdev_down_cmd_non_tlv for vap 0 (da782000) OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (da782000) Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:19227 Comm:30-hyd :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (da782000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-3(ath13):set SIOC80211NWID, 2 characters DES SSID SET=on vap-3(ath13):set SIOC80211NWID, 8 characters DES SSID SET=ORBI08-3 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath13 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath13 DEVICE IS DOWN ifname=ath13 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 3 (da782000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/3 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 3 (da782000) ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 10(ath13) entered forwarding state br0: port 10(ath13) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath13 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:19292 Comm:ifconfig :: PPID:18110 Comm:wlan <=< STOPPED EVENT for vap 3 (da782000) send_vdev_down_cmd_non_tlv for vap 3 (da782000) br0: port 10(ath13) entered disabled state qcawifi: enable radio wifi2 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === Skipping VHT80 channel 5660 Skipping VHT80 channel 5680 Skipping VHT80 channel 5700 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === freq=106 freq=122 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 wlan_vap_create : enter. devhandle=0xd7e004c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 38:94:ed:d1:7a:43: su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 1 sounding dim 0 ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd7e004c0, vap=0xd6fc0000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling TSO bit for the vap ath2 features 4000 Enabling LRO bit for the vap ath2 features 4000 VAP device ath2 created osifp: (d7329cc0) os_if: (d6fc0000) siwfreq Set freq vap 0 stop send + d6fc0000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:19583 Comm:iwconfig :: PPID:19455 Comm:wlan <=< Set freq vap 0 stop send -d6fc0000 Set wait done --d6fc0000 ME Pool succesfully initialized vaddr - d6fe0000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST vap-0(ath2):set SIOC80211NWID, 2 characters DES SSID SET=on vap-0(ath2):set SIOC80211NWID, 6 characters DES SSID SET=ORBI08 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 3 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 device ath2 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 DEVICE IS DOWN ifname=ath2 DEVICE IS DOWN ifname=ath2 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (d7eb0000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 11(ath2) entered forwarding state br0: port 11(ath2) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath2 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:19708 Comm:ifconfig :: PPID:19455 Comm:wlan <=< STOPPED EVENT for vap 0 (d7eb0000) send_vdev_down_cmd_non_tlv for vap 0 (d7eb0000) br0: port 11(ath2) entered disabled state wlan_vap_create : enter. devhandle=0xd7e004c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 1 Type = 1, Subtype = 0 VAP Addr = 3e:94:ed:d1:7a:43: su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 1 sounding dim 0 ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd7e004c0, vap=0xd6470000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath21 features 4000 Enabling SG bit for the vap ath21 features 4000 Enabling SG bit for the vap ath21 features 4000 Enabling TSO bit for the vap ath21 features 4000 Enabling LRO bit for the vap ath21 features 4000 VAP device ath21 created osifp: (d71bc4c0) os_if: (d6470000) siwfreq vap-1(ath21):set SIOC80211NWID, 2 characters DES SSID SET=on vap-1(ath21):set SIOC80211NWID, 21 characters DES SSID SET=NETGEAR_ORBI_hidden10 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 3 0146c Private capibility_data : 0408010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 device ath21 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath21 DEVICE IS DOWN ifname=ath21 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 1 (d7eb0000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 12(ath21) entered forwarding state br0: port 12(ath21) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath21 OK wlan_vap_create : enter. devhandle=0xd7e004c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 2 Type = 1, Subtype = 0 VAP Addr = 42:94:ed:d1:7a:43: su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 1 sounding dim 0 ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd7e004c0, vap=0xd64f8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath22 features 4000 Enabling SG bit for the vap ath22 features 4000 Enabling SG bit for the vap ath22 features 4000 Enabling TSO bit for the vap ath22 features 4000 Enabling LRO bit for the vap ath22 features 4000 VAP device ath22 created osifp: (d6d9c4c0) os_if: (d64f8000) siwfreq Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:19915 Comm:iwpriv :: PPID:19455 Comm:wlan <=< send_vdev_down_cmd_non_tlv for vap 1 (d7eb0000) OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 STOPPED EVENT for vap 1 (d7eb0000) ol_vdev_start_resp_ev for vap 1 (d7eb0000) ol_if_dfs_configure: ETSI domain vap-2(ath22):set SIOC80211NWID, 2 characters DES SSID SET=on vap-2(ath22):set SIOC80211NWID, 12 characters DES SSID SET=ORBI08-GUEST ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 3 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 device ath22 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath22 DEVICE IS DOWN ifname=ath22 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 2 (d7eb0000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 13(ath22) entered forwarding state br0: port 13(ath22) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath22 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20005 Comm:ifconfig :: PPID:19455 Comm:wlan <=< STOPPED EVENT for vap 2 (d7eb0000) send_vdev_down_cmd_non_tlv for vap 2 (d7eb0000) br0: port 13(ath22) entered disabled state wlan_vap_create : enter. devhandle=0xd7e004c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 3 Type = 1, Subtype = 0 VAP Addr = 46:94:ed:d1:7a:43: su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 1 sounding dim 0 ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd7e004c0, vap=0xd6590000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath23 features 4000 Enabling SG bit for the vap ath23 features 4000 Enabling SG bit for the vap ath23 features 4000 Enabling TSO bit for the vap ath23 features 4000 Enabling LRO bit for the vap ath23 features 4000 VAP device ath23 created osifp: (db5454c0) os_if: (d6590000) siwfreq Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20086 Comm:iwpriv :: PPID:19455 Comm:wlan <=< send_vdev_down_cmd_non_tlv for vap 1 (d7eb0000) OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 vap-3(ath23):set SIOC80211NWID, 2 characters DES SSID SET=on vap-3(ath23):set SIOC80211NWID, 8 characters STOPPED EVENT for vap 1 (d7eb0000) ol_vdev_start_resp_ev for vap 1 (d7eb0000) ol_if_dfs_configure: ETSI domain DES SSID SET=ORBI08-2 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 3 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 device ath23 entered promiscuous mode Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath23 DEVICE IS DOWN ifname=ath23 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - send_vdev_down_cmd_non_tlv for vap 0 (dec52000) mlme_create_infra_bss : Overriding HT40 channel with HT20 channel OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 mlme_create_infra_bss : Overriding HT40 channel with HT20 channel OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 ol_vdev_start_resp_ev for vap 0 (dec52000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/2 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (dec52000) ol_vdev_start_resp_ev for vap 3 (d7eb0000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_vdev_start_resp_ev for vap 1 (dec52000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/2 :: PPID:1 Comm:procd <=< su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 1 (dec52000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 14(ath23) entered forwarding state br0: port 14(ath23) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath23 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20178 Comm:ifconfig :: PPID:19455 Comm:wlan <=< STOPPED EVENT for vap 3 (d7eb0000) send_vdev_down_cmd_non_tlv for vap 3 (d7eb0000) br0: port 14(ath23) entered disabled state wlan_vap_create : enter. devhandle=0xd7e004c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 4 Type = 1, Subtype = 0 VAP Addr = 4a:94:ed:d1:7a:43: su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 1 sounding dim 0 ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd7e004c0, vap=0xd6628000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath24 features 4000 Enabling SG bit for the vap ath24 features 4000 Enabling SG bit for the vap ath24 features 4000 Enabling TSO bit for the vap ath24 features 4000 Enabling LRO bit for the vap ath24 features 4000 VAP device ath24 created osifp: (db5474c0) os_if: (d6628000) siwfreq Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20256 Comm:iwpriv :: PPID:19455 Comm:wlan <=< send_vdev_down_cmd_non_tlv for vap 1 (d7eb0000) OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 vap-4(ath24):set SIOC80211NWID, 2 characters DES SSID SET=on STOPPED EVENT for vap 1 (d7eb0000) ol_vdev_start_resp_ev for vap 1 (d7eb0000) ol_if_dfs_configure: ETSI domain vap-4(ath24):set SIOC80211NWID, 8 characters DES SSID SET=ORBI08-3 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 3 0146c Private capibility_data : 0008010000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 device ath24 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath24 DEVICE IS DOWN ifname=ath24 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:3622 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 4 (d7eb0000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 15(ath24) entered forwarding state br0: port 15(ath24) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath24 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20307 Comm:ifconfig :: PPID:19455 Comm:wlan <=< STOPPED EVENT for vap 4 (d7eb0000) send_vdev_down_cmd_non_tlv for vap 4 (d7eb0000) br0: port 15(ath24) entered disabled state iface_mgr: ifacemgr_load_conf_file: 218: No STA VAPs are configured 3e:94:ed:d1:7a:40 38:94:ed:d1:7a:43 iface_mgr: ifacemgr_conn_to_global_wpa_s: 248: connected to global wpa_s iface_mgr: ifacemgr_display_updated_config: 560: Mode:3 timeout:60 [wlan]=========time:Fri Sep 17 01:25:22 UTC 2021 wlan up end================== QCA post_lock_qcawifi Restart hyd after wlan up Saving Data... Done! Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 hyd: starting daemon ath0 IEEE 802.11ng ESSID:"ORBI08" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden10" ath1 IEEE 802.11ac ESSID:"ORBI08" ath02 IEEE 802.11b ESSID:"ORBI08-GUEST" ath11 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath03 IEEE 802.11b ESSID:"ORBI08-2" ath12 IEEE 802.11ac ESSID:"ORBI08-2" ath04 IEEE 802.11b ESSID:"ORBI08-3" ath13 IEEE 802.11ac ESSID:"ORBI08-3" ath2 IEEE 802.11ac ESSID:"ORBI08" ath21 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden10" ath22 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath23 IEEE 802.11ac ESSID:"ORBI08-2" ath24 IEEE 802.11ac ESSID:"ORBI08-3" [ath0] Band steering events being sent to PID:22674 [ath01] Band steering events being sent to PID:22674 [ath1] Band steering events being sent to PID:22674 [ath02] Band steering events being sent to PID:22674 [ath11] Band steering events being sent to PID:22674 [ath03] Band steering events being sent to PID:22674 [ath12] Band steering events being sent to PID:22674 [ath04] Band steering events being sent to PID:22674 [ath13] Band steering events being sent to PID:22674 [ath21] Band steering events being sent to PID:22674 [ath0] Band steering events being sent to PID:22674 [ath1] Band steering events being sent to PID:22674 [ath2] Band steering events being sent to PID:22674 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 hyd: starting daemon [wlan]=========time:Fri Sep 17 01:25:31 UTC 2021 wlan post up ================== [wlan]========= reload netscan ================== [fing-devices]receive SIG15.. Receive SIGTERM, fing-devices process will exit normally!!! 128766:(285): remove subscription Dilsignature (0) 128766:(285): De-registering ntf 128767:(285): (De)registering complete 128770:(284): remove subscription FeatureCfg (0) 128770:(284): De-registering ntf 128770:(284): (De)registering complete 128771:(283): remove subscription DILGeneral (0) 128771:(283): De-registering ntf 128771:(283): (De)registering complete EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts: (null) Run BASE_BOARD net-scan config...The attached devices demo is Running ... Support ssdk switch mac table check function. 129383:(307): add subscription DILGeneral (0) 129383:(307): Registering ntf 129384:(307): (De)registering complete 129385:(308): add subscription FeatureCfg (0) 129385:(308): Registering ntf 129385:(308): (De)registering complete 129387:(309): add subscription Dilsignature (0) 129387:(309): Registering ntf 129387:(309): (De)registering complete net-scan backgroud start scan... [net-scan] start scan devices... [wifi-listener] Starting daemon soap_agent receive AttachDevice SIG net.bridge.bridge-nf-call-custom = 1 Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 ath0 IEEE 802.11ng ESSID:"ORBI08" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden10" ath1 IEEE 802.11ac ESSID:"ORBI08" ath02 IEEE 802.11b ESSID:"ORBI08-GUEST" ath11 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath03 IEEE 802.11b ESSID:"ORBI08-2" ath12 IEEE 802.11ac ESSID:"ORBI08-2" ath04 IEEE 802.11b ESSID:"ORBI08-3" ath13 IEEE 802.11ac ESSID:"ORBI08-3" ath2 IEEE 802.11ac ESSID:"ORBI08" ath21 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden10" ath22 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath23 IEEE 802.11ac ESSID:"ORBI08-2" ath24 IEEE 802.11ac ESSID:"ORBI08-3" [net-scan]receive SIG10.. [fing-devices]receive SIG10.. DIL Total device num=0 Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 hyd: starting daemon Set backhaul AP OtherBand BSSID Otherband BSSID 3e:94:ed:d1:7a:43 Otherband BSSID 42:94:ed:d1:7a:40 [ath0] Band steering events being sent to PID:25316 [ath01] Band steering events being sent to PID:25316 [ath1] Band steering events being sent to PID:25316 [ath02] Band steering events being sent to PID:25316 [ath11] Band steering events being sent to PID:25316 [ath03] Band steering events being sent to PID:25316 [ath12] Band steering events being sent to PID:25316 [ath04] Band steering events being sent to PID:25316 [ath13] Band steering events being sent to PID:25316 [ath21] Band steering events being sent to PID:25316 [ath0] Band steering events being sent to PID:25316 [ath1] Band steering events being sent to PID:25316 [ath2] Band steering events being sent to PID:25316 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 [wlan]===time:Fri Sep 17 01:25:41 UTC 2021 command:wlan stainfo============== soap_agent receive AttachDevice SIG Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 cac_timeout cac expired, chan 5540 curr time 4294843 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 send_vdev_up_cmd_non_tlv for vap 1 (d7eb0000) __ieee80211_smart_ant_init: Smart Antenna is not supported Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 BusyBox v1.24.1 (2021-09-17 08:31:05 CST) multi-call binary. Usage: grep [-HhnlLoqvsriwFE] [-m N] [-A/B/C N] PATTERN/-e PATTERN.../-f FILE [FILE]... Search for PATTERN in FILEs (or stdin) -H Add 'filename:' prefix -h Do not add 'filename:' prefix -n Add 'line_no:' prefix -l Show only names of files that match -L Show only names of files that don't match -c Show only count of matching lines -o Show only the matching part of line -q Quiet. Return 0 if PATTERN is found, 1 otherwise -v Select non-matching lines -s Suppress open and read errors -r Recurse -i Ignore case -w Match whole words only -x Match whole lines only -F PATTERN is a literal (not regexp) -E PATTERN is an extended regexp -m N Match up to N times per file -A N Print N lines of trailing context -B N Print N lines of leading context -C N Same as '-A N -B N' -e PTRN Pattern to match -f FILE Read pattern from file Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 [wlan]===time:Fri Sep 17 01:26:45 UTC 2021 command:wlan updateconf============== [wlan]=========time:Fri Sep 17 01:26:45 UTC 2021 wlan updateconf start====== sh: bad number [wlan]=========time:Fri Sep 17 01:26:53 UTC 2021 wlan updateconf end====== QCA post_updateconf_qcawifi Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 ath0 IEEE 802.11ng ESSID:"ORBI08" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden10" ath1 IEEE 802.11ac ESSID:"ORBI08" ath02 IEEE 802.11b ESSID:"ORBI08-GUEST" ath11 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath03 IEEE 802.11b ESSID:"ORBI08-2" ath12 IEEE 802.11ac ESSID:"ORBI08-2" ath04 IEEE 802.11b ESSID:"ORBI08-3" ath13 IEEE 802.11ac ESSID:"ORBI08-3" ath2 IEEE 802.11ac ESSID:"ORBI08" ath21 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden10" ath22 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath23 IEEE 802.11ac ESSID:"ORBI08-2" ath24 IEEE 802.11ac ESSID:"ORBI08-3" hyd: starting daemon [ath0] Band steering events being sent to PID:1784 [ath01] Band steering events being sent to PID:1784 [ath1] Band steering events being sent to PID:1784 [ath02] Band steering events being sent to PID:1784 [ath03] Band steering events being sent to PID:1784 [ath12] Band steering events being sent to PID:1784 [ath04] Band steering events being sent to PID:1784 [ath13] Band steering events being sent to PID:1784 [ath21] Band steering events being sent to PID:1784 [ath0] Band steering events being sent to PID:1784 [ath1] Band steering events being sent to PID:1784 [ath2] Band steering events being sent to PID:1784 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 [wlan]===time:Fri Sep 17 01:27:02 UTC 2021 command:wlan updateconf============== [wlan]=========time:Fri Sep 17 01:27:02 UTC 2021 wlan updateconf start====== sh: bad number [wlan]=========time:Fri Sep 17 01:27:11 UTC 2021 wlan updateconf end====== QCA post_updateconf_qcawifi Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 ath0 IEEE 802.11ng ESSID:"ORBI08" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden10" ath1 IEEE 802.11ac ESSID:"ORBI08" ath02 IEEE 802.11b ESSID:"ORBI08-GUEST" ath11 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath03 IEEE 802.11b ESSID:"ORBI08-2" ath12 IEEE 802.11ac ESSID:"ORBI08-2" ath04 IEEE 802.11b ESSID:"ORBI08-3" ath13 IEEE 802.11ac ESSID:"ORBI08-3" ath2 IEEE 802.11ac ESSID:"ORBI08" ath21 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden10" ath22 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath23 IEEE 802.11ac ESSID:"ORBI08-2" ath24 IEEE 802.11ac ESSID:"ORBI08-3" hyd: starting daemon [ath0] Band steering events being sent to PID:6050 [ath01] Band steering events being sent to PID:6050 [ath1] Band steering events being sent to PID:6050 [ath03] Band steering events being sent to PID:6050 [ath12] Band steering events being sent to PID:6050 [ath04] Band steering events being sent to PID:6050 [ath13] Band steering events being sent to PID:6050 [ath21] Band steering events being sent to PID:6050 [ath0] Band steering events being sent to PID:6050 [ath1] Band steering events being sent to PID:6050 [ath2] Band steering events being sent to PID:6050 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 [wlan]===time:Fri Sep 17 01:27:20 UTC 2021 command:wlan updateconf============== [wlan]=========time:Fri Sep 17 01:27:20 UTC 2021 wlan updateconf start====== Configuration: NTP server : time-h.netgear.com Interval : 10 Local port :123 sh: bad number [wlan]=========time:Fri Sep 17 01:27:29 UTC 2021 wlan updateconf end====== QCA post_updateconf_qcawifi Configuration: NTP server : time-g.netgear.com Interval : 10 Local port :123 ath0 IEEE 802.11ng ESSID:"ORBI08" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden10" ath1 IEEE 802.11ac ESSID:"ORBI08" ath02 IEEE 802.11b ESSID:"ORBI08-GUEST" ath11 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath03 IEEE 802.11b ESSID:"ORBI08-2" ath12 IEEE 802.11ac ESSID:"ORBI08-2" ath04 IEEE 802.11b ESSID:"ORBI08-3" ath13 IEEE 802.11ac ESSID:"ORBI08-3" ath2 IEEE 802.11ac ESSID:"ORBI08" ath21 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden10" ath22 IEEE 802.11ac ESSID:"ORBI08-GUEST" ath23 IEEE 802.11ac ESSID:"ORBI08-2" ath24 IEEE 802.11ac ESSID:"ORBI08-3" hyd: starting daemon [ath0] Band steering events being sent to PID:10256 [ath01] Band steering events being sent to PID:10256 [ath1] Band steering events being sent to PID:10256 [ath03] Band steering events being sent to PID:10256 [ath04] Band steering events being sent to PID:10256 [ath13] Band steering events being sent to PID:10256 [ath21] Band steering events being sent to PID:10256 [ath0] Band steering events being sent to PID:10256 [ath1] Band steering events being sent to PID:10256 [ath2] Band steering events being sent to PID:10256 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 38:94:ed:d1:7a:40 [wlan]===time:Fri Sep 17 01:27:38 UTC 2021 command:wlan updateconf============== [wlan]=========time:Fri Sep 17 01:27:38 UTC 2021 wlan updateconf start====== sh: bad number

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 S - IMAGE_VARIANT_STRING=DAAAANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000023 S - Reset status Config, 0x00000000 S - Core 0 Frequency, 0 MHz B - 262 - PBL, Start B - 1343 - bootable_media_detect_entry, Start B - 34636 - bootable_media_detect_success, Start B - 34651 - elf_loader_entry, Start B - 36864 - auth_hash_seg_entry, Start B - 39039 - auth_hash_seg_exit, Start B - 76161 - elf_segs_hash_verify_entry, Start B - 191489 - PBL, End B - 191513 - SBL1, Start B - 283722 - pm_device_init, Start D - 9 - pm_device_init, Delta B - 285240 - boot_flash_init, Start D - 37033 - boot_flash_init, Delta B - 326582 - boot_config_data_table_init, Start D - 2717 - boot_config_data_table_init, Delta - (419 Bytes) B - 334252 - clock_init, Start D - 7518 - clock_init, Delta B - 345540 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 B - 348946 - sbl1_ddr_set_params, Start B - 354040 - cpr_init, Start D - 2 - cpr_init, Delta B - 358423 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13172 - sbl1_ddr_set_params, Delta B - 371718 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 442965 - sbl1_wait_for_ddr_training, Start D - 27 - sbl1_wait_for_ddr_training, Delta B - 459145 - Image Load, Start D - 15031 - QSEE Image Loaded, Delta - (268920 Bytes) B - 474604 - Image Load, Start D - 898 - SEC Image Loaded, Delta - (0 Bytes) B - 484453 - Image Load, Start D - 12615 - APPSBL Image Loaded, Delta - (421607 Bytes) B - 497494 - QSEE Execution, Start D - 60 - QSEE Execution, Delta B - 503669 - SBL1, End D - 314268 - SBL1, Delta S - Flash Throughput, 25207 KB/s (691298 Bytes, 27424 us) S - DDR Frequency, 672 MHz U-Boot 2012.07-g9274bc2-dirty [Barrier Breaker unknown,unknown] (Jun 16 2017 - 16:27:21) U-boot dni1 V1.1 for DNI HW ID: 29765352; NOR flash 0MB; EMMC flash 4096MB; RAM 512MB smem ram ptable found: ver: 1 len: 3 DRAM: 512 MiB machid : 0x8010001 NAND: ID = 0 Vendor = 0 Device = 0 Nand Flash error. Status = 64 ONFI Read id cmd failed ONFI probe failed SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 0 MiB MMC: qca_mmc: 0 *** Warning - bad CRC, using default environment PCI0 Link Intialized In: serial Out: serial Err: serial Valid chip addresses: 27 48 machid: 8010001 flash_type: 1 Net: MAC0 addr:38:94:ed:d1:7a:40 PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Hit any key to stop autoboot: 2 1 0 eth0 PHY0 Down Speed :10 Half duplex eth0 PHY1 Down Speed :10 Half duplex eth0 PHY2 Down Speed :10 Half duplex eth0 PHY3 Down Speed :10 Half duplex eth0 PHY4 Down Speed :10 Half duplex nmrp server is stopped or failed ! Read BootPart from BOARD DATA... mmc_read will run command: mmc read 0x871cfba8 0x2c22 0x100 MMC read: dev # 0, block # 11298, count 256 ... 256 blocks read: OK boot partition : 1 BootPart = 1 Loading DNI firmware for checking... MMC read: dev # 0, block # 18466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24610, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24866, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25122, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18466, count 1 ... 1 blocks read: OK ** rootfs address : 0x8435ffc0 ** ## Checking Image at 84000000 ... FIT image found FIT description: ARM OpenWrt FIT (Flattened Image Tree) Image 0 (kernel-1) Description: ARM OpenWrt Linux-6.12.94 Type: Kernel Image Compression: uncompressed Data Start: 0x840000e4 Data Size: 3419792 Bytes = 3.3 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 8df12ab9 Hash algo: sha1 Hash value: 2c50656c534222e8cb3883ac0032f1ca170e2dcd Image 1 (fdt-1) Description: ARM OpenWrt netgear_srr60 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843430ac Data Size: 18912 Bytes = 18.5 KiB Architecture: ARM Hash algo: crc32 Hash value: da81d487 Hash algo: sha1 Hash value: 53de94c95e1d960c42761089fad6b3d61b0d4ffe Default Configuration: 'config@1' Configuration 0 (config@1) Description: OpenWrt netgear_srr60 Kernel: kernel-1 FDT: fdt-1 ## Checking hash(es) for FIT Image at 84000000 ... Hash(es) for Image 0 (kernel-1): crc32+ sha1+ Hash(es) for Image 1 (fdt-1): crc32+ sha1+ ## Checking Image at 8435ffc0 ... Legacy image found Image Name: OpenWrt fake filesystem Image Type: ARM Linux Filesystem Image (uncompressed) Data Size: 0 Bytes = 0 Bytes Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK mmc_read will run command: mmc read 0x871cfba8 0x2c22 0x100 MMC read: dev # 0, block # 11298, count 256 ... 256 blocks read: OK boot partition : 1 MMC read: dev # 0, block # 18466, count 7680 ... 7680 blocks read: OK ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-6.12.94 Type: Kernel Image Compression: uncompressed Data Start: 0x840000e4 Data Size: 3419792 Bytes = 3.3 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 8df12ab9 Hash algo: sha1 Hash value: 2c50656c534222e8cb3883ac0032f1ca170e2dcd Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt-1' FDT blob subimage Description: ARM OpenWrt netgear_srr60 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843430ac Data Size: 18912 Bytes = 18.5 KiB Architecture: ARM Hash algo: crc32 Hash value: da81d487 Hash algo: sha1 Hash value: 53de94c95e1d960c42761089fad6b3d61b0d4ffe Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x843430ac Loading Kernel Image ... OK OK Loading Device Tree to 871e7000, end 871ee9df ... OK Using machid 0x8010001 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.94 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 14.3.0 r33051-f5dae5ece4) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Mon Jun 29 12:59:20 2026 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: NETGEAR SRR60 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x0000000087dfffff] [ 0.000000] node 0: [mem 0x0000000087e00000-0x0000000087ffffff] [ 0.000000] node 0: [mem 0x0000000088000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] OF: reserved mem: 0x87e00000..0x87e7ffff (512 KiB) nomap non-reusable smem@87e00000 [ 0.000000] OF: reserved mem: 0x87e80000..0x87ffffff (1536 KiB) nomap non-reusable tz@87e80000 [ 0.000000] percpu: Embedded 14 pages/cpu s25420 r8192 d23732 u57344 [ 0.000000] Kernel command line: root=/dev/mmcblk0p20 blkdevparts=mmcblk0:512K@17K(0:SBL1)ro,512K(0:BOOTCONFIG)ro,512K(0:QSEE)ro,512K(0:QSEE_1)ro,256K(0:CDT)ro,256K(0:CDT_1)ro,512K(0:BOOTCONFIG1)ro,256K(0:APPSBLENV)ro,1M(0:APPSBL)ro,1M(0:APPSBL_1)ro,256K(0:ART)ro,256K(ARTMTD)ro,2M(language)ro,256K(config)ro,256K(pot)ro,256K(traffic_meter)ro,256K(pot_bak)ro,256K(traffic_meter.bak)ro,3840K(kernel),31488K(rootfs),35328K@9233K(firmware),256K(mtdoops)ro,64K(cert)ro,3840K(kernel-2)ro,31488K(rootfs-2)ro,35328K@44881K(firmware-2)ro,5M(device_table)ro,17M(cp_file)ro,102737K(reserved)ro,-(unallocated) rootfstype=squashfs,ext4 rootwait [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000002] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000020] Switching to timer-based delay loop, resolution 20ns [ 0.000323] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000345] CPU: Testing write buffer coherency: ok [ 0.000405] pid_max: default: 32768 minimum: 301 [ 0.013305] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.013330] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.018863] qcom_scm: convention: smc legacy [ 0.020835] Setting up static identity map for 0x80300000 - 0x8030003c [ 0.021066] rcu: Hierarchical SRCU implementation. [ 0.021075] rcu: Max phase no-delay instances is 1000. [ 0.021551] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.022211] smp: Bringing up secondary CPUs ... [ 0.026289] smp: Brought up 1 node, 4 CPUs [ 0.026314] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.026328] CPU: All CPU(s) started in SVC mode. [ 0.027422] Memory: 503448K/524288K available (7996K kernel code, 635K rwdata, 1224K rodata, 1024K init, 255K bss, 19552K reserved, 0K cma-reserved, 0K highmem) [ 0.035094] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.035314] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.035344] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.041858] pinctrl core: initialized pinctrl subsystem [ 0.045271] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.045676] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.047064] thermal_sys: Registered thermal governor 'step_wise' [ 0.047180] cpuidle: using governor ladder [ 0.047223] cpuidle: using governor menu [ 0.070803] cryptd: max_cpu_qlen set to 1000 [ 0.075739] usbcore: registered new interface driver usbfs [ 0.075804] usbcore: registered new interface driver hub [ 0.075862] usbcore: registered new device driver usb [ 0.075919] pps_core: LinuxPPS API ver. 1 registered [ 0.075927] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.075953] PTP clock support registered [ 0.078842] clocksource: Switched to clocksource arch_sys_counter [ 0.089724] NET: Registered PF_INET protocol family [ 0.089969] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.092367] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.092414] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.092435] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.092504] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.092657] TCP: Hash tables configured (established 4096 bind 4096) [ 0.093297] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.093696] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.093736] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.094472] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.094528] PCI: CLS 0 bytes, default 64 [ 0.096338] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.098486] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.098501] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.422930] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.427975] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.428132] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.428237] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.428362] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.428882] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.429970] qcom-pcie 40000000.pcie: host bridge /soc/pcie@40000000 ranges: [ 0.430044] qcom-pcie 40000000.pcie: IO 0x0040200000..0x00402fffff -> 0x0000000000 [ 0.430080] qcom-pcie 40000000.pcie: MEM 0x0040300000..0x0040ffffff -> 0x0040300000 [ 0.433369] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.433480] msm_serial 78af000.serial: uartclk = 1843200 [ 0.433993] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 31, base_baud = 115200) is a MSM [ 0.434046] msm_serial: console setup on port #0 [ 0.434102] printk: legacy console [ttyMSM0] enabled [ 0.560703] qcom-pcie 40000000.pcie: iATU: unroll F, 32 ob, 8 ib, align 4K, limit 4G [ 0.587382] msm_serial: driver initialized [ 0.609212] qcom-pcie 40000000.pcie: Invalid eDMA IRQs found [ 0.708858] qcom-pcie 40000000.pcie: PCIe Gen.2 x1 link up [ 0.720458] loop: module loaded [ 0.723800] qcom-pcie 40000000.pcie: PCI host bridge to bus 0000:00 [ 0.775373] i2c_dev: i2c /dev entries driver [ 0.777026] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.781576] i2c_qup 78b7000.i2c: using default clock-frequency 100000 [ 0.785373] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] [ 1.152498] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] [ 1.158624] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400 PCIe Root Port [ 1.165534] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x00000fff] [ 1.172725] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.178604] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.183828] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.190094] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref] [ 1.196882] pci 0000:00:00.0: PME# supported from D0 D3hot [ 1.206395] PCI: bus0: Fast back to back transfers disabled [ 1.210309] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000 PCIe Endpoint [ 1.215528] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x001fffff 64bit] [ 1.223375] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.229948] PCI: bus1: Fast back to back transfers disabled [ 1.235318] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff]: assigned [ 1.240705] pci 0000:00:00.0: BAR 0 [mem 0x40300000-0x40300fff]: assigned [ 1.248314] pci 0000:01:00.0: BAR 0 [mem 0x40400000-0x405fffff 64bit]: assigned [ 1.255157] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.262214] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] [ 1.267408] pci_bus 0000:00: resource 4 [io 0x0000-0xfffff] [ 1.274362] pci_bus 0000:00: resource 5 [mem 0x40300000-0x40ffffff] [ 1.280092] pci_bus 0000:01: resource 1 [mem 0x40400000-0x405fffff] [ 1.290355] pcieport 0000:00:00.0: AER: enabled with IRQ 59 [ 1.297798] sdhci: Secure Digital Host Controller Interface driver [ 1.297872] sdhci: Copyright(c) Pierre Ossman [ 1.304163] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.309544] sdhci_msm 7824900.mmc: Got CD GPIO [ 1.312661] NET: Registered PF_INET6 protocol family [ 1.321563] Segment Routing with IPv6 [ 1.323733] In-situ OAM (IOAM) with IPv6 [ 1.327347] NET: Registered PF_PACKET protocol family [ 1.331294] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.336699] 8021q: 802.1Q VLAN Support v1.8 [ 1.349568] Registering SWP/SWPB emulation handler [ 1.372367] mmc0: SDHCI controller on 7824900.mmc [7824900.mmc] using ADMA 64-bit [ 1.380935] qca8k-ipq4019 c000000.switch: configuring for fixed/internal link mode [ 1.381257] qca8k-ipq4019 c000000.switch: Link is Up - 1Gbps/Full - flow control rx/tx [ 1.425327] mmc0: new HS200 MMC card at address 0001 [ 1.426508] mmcblk0: mmc0:0001 M62704 3.53 GiB [ 1.430368] Overlapping partitions are used in command line partitions. [ 1.430384] Don't use filesystems on overlapping partitions: [ 1.433634] kernel[9454592,3932160] overlaps with firmware[9454592,36175872]. [ 1.440170] rootfs[13386752,32243712] overlaps with firmware[9454592,36175872]. [ 1.446050] kernel-2[45958144,3932160] overlaps with firmware-2[45958144,36175872]. [ 1.453104] rootfs-2[49890304,32243712] overlaps with firmware-2[45958144,36175872]. [ 1.460222] mmcblk0: p1(0:SBL1) p2(0:BOOTCONFIG) p3(0:QSEE) p4(0:QSEE_1) p5(0:CDT) p6(0:CDT_1) p7(0:BOOTCONFIG1) p8(0:APPSBLENV) p9(0:APPSBL) p10(0:APPSBL_1) p11(0:ART) p12(ARTMTD) p13(language) p14(config) p15(pot) p16(traffic_meter) p17(pot_bak) p18(traffic_meter.bak) p19(kernel) p20(rootfs) p21(firmware) p22(mtdoops) p23(cert) p24(kernel-2) p25(rootfs-2) p26(firmware-2) p27(device_table) p28(cp_file) p29(reserved) p30(unallocated) [ 1.495763] mmcblk0boot0: mmc0:0001 M62704 2.00 MiB [ 1.515238] mmcblk0boot1: mmc0:0001 M62704 2.00 MiB [ 1.519636] mmcblk0rpmb: mmc0:0001 M62704 512 KiB, chardev (246:0) [ 1.560546] qca8k-ipq4019 c000000.switch wan (uninitialized): PHY [90000.mdio-1:00] driver [Qualcomm QCA8075] (irq=POLL) [ 1.629583] qca8k-ipq4019 c000000.switch lan1 (uninitialized): PHY [90000.mdio-1:01] driver [Qualcomm QCA8075] (irq=POLL) [ 1.699562] qca8k-ipq4019 c000000.switch lan2 (uninitialized): PHY [90000.mdio-1:02] driver [Qualcomm QCA8075] (irq=POLL) [ 1.769563] qca8k-ipq4019 c000000.switch lan3 (uninitialized): PHY [90000.mdio-1:03] driver [Qualcomm QCA8075] (irq=POLL) [ 1.770811] ipqess-edma c080000.ethernet eth0: entered promiscuous mode [ 1.779676] DSA: tree 0 setup\8A[ 1.794234] VFS: Mounted root (squashfs filesystem) readonly on device 259:12. [ 1.796277] Freeing unused kernel image (initmem) memory: 1024K [ 1.800677] Run /sbin/init as init process [ 2.154788] init: Console is alive [ 2.155126] init: - watchdog - [ 2.926814] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.004663] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 3.024643] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.027153] init: - preinit - [ 7.588870] random: crng init done Cannot parse config file '/etc/fw_env.config': No such file or directory Failed to find NVMEM device [ 8.283345] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode [ 8.284149] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode [ 8.290237] qca8k-ipq4019 c000000.switch: PSGMII calibration! [ 8.297939] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.695227] loop0: detected capacity change from 0 to 62976 [ 13.748878] loop0: detected capacity change from 62976 to 51712 [ 13.799490] EXT4-fs (loop0): recovery complete [ 13.800839] EXT4-fs (loop0): mounted filesystem bf3d0e4f-1d56-4cb6-b685-a6feb5b38c28 r/w with ordered data mode. Quota mode: disabled. [ 13.804052] mount_root: overlay filesystem has not been fully initialized yet [ 13.826642] mount_root: switching to ext4 overlay [ 13.832691] urandom-seed: Seed file not found (/etc/urandom.seed) - generating board file - [ 14.381609] procd: - early - [ 14.381852] procd: - watchdog - [ 14.984135] procd: - watchdog - [ 14.985207] procd: - ubus - [ 15.075946] procd: - init - Please press Enter to activate this console. [ 15.867180] kmodloader: loading kernel modules from /etc/modules.d/* [ 15.923920] Loading modules backported from Linux version v6.18.26-0-g1fe060681 [ 15.923982] Backport generated by backports.git 6ecbb44 [ 16.151274] PPP generic driver version 2.4.2 [ 16.152557] NET: Registered PF_PPPOX protocol family [ 16.180756] ath10k 6.15 driver, optimized for CT firmware, probing pci device: 0x46. [ 16.181845] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 16.188247] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 16.426906] urngd: v1.0.2 started. [ 17.243107] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 17.243189] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 17.256210] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-14-fcb240f048 api 5 features mfp,peer-flow-ctrl,peer-fixed-rate,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 ba7d918c [ 19.597017] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:6 crc32 0bfe5c35 [ 23.101458] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 23.101538] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 23.184796] ath10k_pci 0000:01:00.0: wmi print 'ChipType 1100 ChipTypeID 0 BoardID 2 P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 23.185607] ath10k_pci 0000:01:00.0: wmi print 'free: 85096 iram: 19604 sram: 12824' [ 23.385131] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 24.718651] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 24.718729] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 24.730639] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-14-fcb240f0 api 5 features mfp,peer-flow-ctrl,peer-fixed-rate,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 0cc1593e [ 24.860208] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 9eac77d9 [ 26.116702] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 26.116794] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 26.164689] ath10k_ahb a000000.wifi: wmi print 'ChipType 1100 ChipTypeID 30 BoardID 14 P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 26.165530] ath10k_ahb a000000.wifi: wmi print 'free: 53428 iram: 20552 sram: 37256' [ 26.339582] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 27.346347] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 27.346441] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 27.358355] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-14-fcb240f0 api 5 features mfp,peer-flow-ctrl,peer-fixed-rate,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 0cc1593e [ 27.415473] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 9eac77d9 [ 28.673449] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 28.673530] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 28.720603] ath10k_ahb a800000.wifi: wmi print 'ChipType 1100 ChipTypeID 30 BoardID 15 P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 28.721551] ath10k_ahb a800000.wifi: wmi print 'free: 53428 iram: 20552 sram: 37256' [ 28.860833] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 28.981255] kmodloader: done loading kernel modules from /etc/modules.d/* [ 44.866832] ipqess-edma c080000.ethernet eth0: Link is Down [ 44.874030] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode [ 44.874423] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 44.891170] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode [ 44.891957] br-lan: port 1(lan1) entered blocking state [ 44.897690] br-lan: port 1(lan1) entered disabled state [ 44.903098] qca8k-ipq4019 c000000.switch lan1: entered allmulticast mode [ 44.908110] ipqess-edma c080000.ethernet eth0: entered allmulticast mode [ 44.915625] qca8k-ipq4019 c000000.switch lan1: entered promiscuous mode [ 44.943777] qca8k-ipq4019 c000000.switch lan2: configuring for phy/psgmii link mode [ 44.945428] br-lan: port 2(lan2) entered blocking state [ 44.950467] br-lan: port 2(lan2) entered disabled state [ 44.955619] qca8k-ipq4019 c000000.switch lan2: entered allmulticast mode [ 44.961481] qca8k-ipq4019 c000000.switch lan2: entered promiscuous mode [ 44.977866] qca8k-ipq4019 c000000.switch lan3: configuring for phy/psgmii link mode [ 44.979626] br-lan: port 3(lan3) entered blocking state [ 44.984389] br-lan: port 3(lan3) entered disabled state [ 44.989806] qca8k-ipq4019 c000000.switch lan3: entered allmulticast mode [ 44.995509] qca8k-ipq4019 c000000.switch lan3: entered promiscuous mode [ 45.016001] qca8k-ipq4019 c000000.switch wan: configuring for phy/psgmii link mode

You can check and edit the boot partition in the Uboot shell using the UART connection
- boot_partition_show shows the current boot partition
- boot_partition_set 1 sets the current boot partition to 1
Router MAC addresses:
- LAN XX:XX:XX:XX:XX:69
- WAN XX:XX:XX:XX:XX:6a
- WIFI 2G XX:XX:XX:XX:XX:69
- WIFI 5G XX:XX:XX:XX:XX:6b
- WIFI 5G (2nd) XX:XX:XX:XX:XX:6c
- LABEL XX:XX:XX:XX:XX:69

How to add tags

ipq40xx, 4096emmc, 512ram, 4port, GigabitEthernet, srk60

ipq40xx 4096emmc 512ram 4port gigabitethernet srk60

Netgear SRR60

Supported Versions

Experimental Versions

Hardware Highlights

Installation

NMRPflash Method

Vendor-UI Method

Revert to stock firmware

Flash Layout

Upgrading OpenWrt

Debricking

Failsafe mode

Basic configuration

Specific Configuration

Network interfaces

Switch Ports (for VLANs)

Buttons

Hardware

Info

Photos

Opening the case

Serial

JTAG

Bootloader mods

Hardware mods

Bootlogs

OEM bootlog

OpenWrt bootlog

Notes

Tags