NETGEAR RBS50

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The RBS50 is the satellite part of the RBK50 kit, which consists of a router and one or more satellites, all of them being AC-3000 devices.

The current instructions are for the v1 of the RBK50 devices only! There currently is no stable v2 release.

Currently not supported.

None at this time.

NMRPflash Method

Download nmrpflash
Put the OpenWRT factory image file in the same folder of the nmrpflash executable
Connect your PC to the router using the port near the power button
Power on the router while holding down the reset button with a pin
Once the power LED starts flashing red, while still holding the reset button, start nmrpflash. Replace XXX with your network interface (can be identified by running nmrpflash -L) and FILE with the file you downloaded

$ nmrpflash -i XXX -f FILE

The power LED will briefly flash green after about 7 red flashes. Remove the pin and quickly unplug and replug the power to the device. The flashing process should then complete.
Reboot the device once prompted.

After about a minute the router should boot directly to OpenWRT and the halo LED should be solid green. If nothing happens, try to reboot the router. If you have problems flashing try to set “10.164.183.253” as your computer IP address. Additionally, you can reference this thread.

Vendor-UI Method

The Vendor web interface will always flash on the partition currently not booted, so to flash OpenWRT for the first time you have to switch to boot partition 2 and then flash the factory image directly from the Vendor web interface. To switch on partition 2 you have to enable telnet first.

Go to http://192.168.1.250/debug.htm and check “Enable Telnet”.
Connect through telnet and login using admin/password.

$ telnet 192.168.1.250

Read the current boot partition

$ artmtd -r boot_part

Write the new boot_part

$ artmtd -w boot_part 02

Reboot and re-check that the currently booted partition is partition 2
Flash the OpenWRT image trough the Vendor-UI

Revert to stock firmware

Download the stock firmware from official NETGEAR support
Follow the nmrpflash procedure like above, using the official Netgear firmware (for example RBS50-V2.2.1.210.img)

$ nmrpflash -i XXX -f FILE

Currently not available.

Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

→ generic.sysupgrade

→ generic.debrick

If the router is bricked it can still be saved through nrmpflash. Please refer to the installation steps above.

Currently not available.

→ failsafe_and_factory_reset

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	EXAMPLE LAN & WiFi	EXAMPLE 192.168.1.1/24
vlan0 (eth0.0)	EXAMPLE LAN ports (1 to 4)	EXAMPLE None
vlan1 (eth0.1)	EXAMPLE WAN port	EXAMPLE DHCP
wl0	EXAMPLE WiFi	EXAMPLE Disabled

Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port	Switch port
Internet (WAN)	EXAMPLE 4
LAN 1	EXAMPLE 3
LAN 2	EXAMPLE 2
LAN 3	EXAMPLE 1
LAN 4	EXAMPLE 0

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The NETGEAR RBS50 has the following buttons:

BUTTON	Event
Reset	restart
WPS	wps

Front:

Back:

Backside label:

→ Warranty

1. Remove the label on the the backside to reveal two screws

2. Unscrew the screws using a TR10 (Torx) bit

3. Remove the two smaller rubber feets on the bottom

4. Slide the front part of the case (with the “Orbi” text) down a bit

5. “Unfold” the case

Main PCB:
Insert photo of PCB

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial connection parameters for NETGEAR RBS 50 v1	115200, 8N1, Voltage unknown

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

→ bootloader

None so far.

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 S - IMAGE_VARIANT_STRING=DAAAANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000023 S - Reset status Config, 0x00000000 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1339 - bootable_media_detect_entry, Start B - 145161 - bootable_media_detect_success, Start B - 145175 - elf_loader_entry, Start B - 147549 - auth_hash_seg_entry, Start B - 149694 - auth_hash_seg_exit, Start B - 186591 - elf_segs_hash_verify_entry, Start B - 300833 - PBL, End B - 300857 - SBL1, Start B - 392867 - pm_device_init, Start D - 9 - pm_device_init, Delta B - 394369 - boot_flash_init, Start D - 27940 - boot_flash_init, Delta B - 426659 - boot_config_data_table_init, Start D - 2848 - boot_config_data_table_init, Delta - (419 Bytes) B - 434408 - clock_init, Start D - 7528 - clock_init, Delta B - 445701 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 B - 449107 - sbl1_ddr_set_params, Start B - 454201 - cpr_init, Start D - 2 - cpr_init, Delta B - 458584 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13171 - sbl1_ddr_set_params, Delta B - 471880 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 543200 - sbl1_wait_for_ddr_training, Start D - 27 - sbl1_wait_for_ddr_training, Delta B - 559375 - Image Load, Start D - 14839 - QSEE Image Loaded, Delta - (262104 Bytes) B - 574642 - Image Load, Start D - 899 - SEC Image Loaded, Delta - (0 Bytes) B - 584495 - Image Load, Start D - 12478 - APPSBL Image Loaded, Delta - (416039 Bytes) B - 597400 - QSEE Execution, Start D - 60 - QSEE Execution, Delta B - 603575 - SBL1, End D - 304830 - SBL1, Delta S - Flash Throughput, 25954 KB/s (678738 Bytes, 26151 us) S - DDR Frequency, 672 MHz U-Boot 2012.07 [Barrier Breaker unknown,unknown] (Jan 04 2017 - 13:54:09) U-boot dni1 V1.4 for DNI HW ID: 29765352; NOR flash 32MB; EMMC flash 4000MB; RAM 512MB smem ram ptable found: ver: 1 len: 3 DRAM: 512 MiB machid : 0x8010001 NAND: ID = 0 Vendor = 0 Device = 0 Nand Flash error. Status = 64 ONFI Read id cmd failed ONFI probe failed SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 0 MiB MMC: qca_mmc: 0 *** Warning - bad CRC, using default environment PCI0 Link Intialized In: serial Out: serial Err: serial Valid chip addresses: 27 48 machid: 8010001 flash_type: 1 Net: MAC0 addr:8c:3b:ad:24:db:89 PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Hit any key to stop autoboot: 2 1 0 eth0 PHY0 Down Speed :10 Half duplex eth0 PHY1 Down Speed :10 Half duplex eth0 PHY2 Down Speed :10 Half duplex eth0 PHY3 Down Speed :10 Half duplex eth0 PHY4 Down Speed :10 Half duplex nmrp server is stopped or failed ! Read BootPart from BOARD DATA... mmc_read will run command: mmc read 0x871cfca8 0x2a22 0x100 MMC read: dev # 0, block # 10786, count 256 ... 256 blocks read: OK boot partition : 1 BootPart = 1 Loading DNI firmware for checking... MMC read: dev # 0, block # 17954, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18210, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24610, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24866, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25122, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25378, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25634, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25890, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26146, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26402, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26658, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26914, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27170, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27426, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27682, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27938, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28194, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28450, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28706, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28962, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29218, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29474, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29730, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29986, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30242, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30498, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30754, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31010, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31266, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31522, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31778, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32034, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32290, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32546, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32802, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33058, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33314, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33570, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33826, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34082, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34338, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34594, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34850, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35106, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35362, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35618, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35874, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36130, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36386, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36642, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36898, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37154, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37410, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37666, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37922, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38178, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38434, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38690, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38946, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39202, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39458, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39714, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39970, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40226, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40482, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40738, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40994, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41250, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41506, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41762, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42018, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42274, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42530, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42786, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43042, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43298, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43554, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43810, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44066, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44322, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44578, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44834, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45090, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45346, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45602, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45858, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46114, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46370, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46626, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46882, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47138, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47394, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47650, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47906, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48162, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48418, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48674, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48930, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49186, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49442, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49698, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49954, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50210, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56610, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56866, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57122, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57378, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57634, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57890, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58146, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58402, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58658, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58914, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59170, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59426, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59682, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59938, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60194, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60450, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60706, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60962, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61218, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61474, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61730, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61986, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62242, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62498, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62754, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63010, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63266, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63522, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63778, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64034, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64290, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64546, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64802, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65058, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65314, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65570, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65826, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66082, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66338, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66594, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66850, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67106, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67362, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67618, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67874, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68130, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68386, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68642, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68898, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69154, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69410, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69666, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69922, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70178, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70434, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70690, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70946, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71202, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 17954, count 1 ... 1 blocks read: OK ** rootfs address : 0x8433ffc0 ** ## Checking Image at 84000000 ... FIT image found FIT description: ARM OpenWrt FIT (Flattened Image Tree) Image 0 (kernel@1) Description: ARM OpenWrt Linux-3.14.77 Type: Kernel Image Compression: gzip compressed Data Start: 0x840000e4 Data Size: 3056294 Bytes = 2.9 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: e7747ae9 Hash algo: sha1 Hash value: 3ef2932a82d4bc46fd4600d69ca9b7b066b4fec9 Image 1 (fdt@1) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842ea4d0 Data Size: 39067 Bytes = 38.2 KiB Architecture: ARM Hash algo: crc32 Hash value: f94716db Hash algo: sha1 Hash value: 7e37e5ed95940f74e51add9aab58a3766e853729 Image 2 (fdt@2) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842f3e7c Data Size: 38617 Bytes = 37.7 KiB Architecture: ARM Hash algo: crc32 Hash value: 50582aa9 Hash algo: sha1 Hash value: 2a3fbefc43355e6855fe31bf63c7cbffee5067c8 Image 3 (fdt@3) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842fd668 Data Size: 42101 Bytes = 41.1 KiB Architecture: ARM Hash algo: crc32 Hash value: a86a5a0f Hash algo: sha1 Hash value: d6d121dcb507c188204ead82dd13e451c38d3798 Image 4 (fdt@4) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84307bf0 Data Size: 34248 Bytes = 33.4 KiB Architecture: ARM Hash algo: crc32 Hash value: 020c9585 Hash algo: sha1 Hash value: e3dce04fd31148b508565288a48559278eca0a3e Image 5 (fdt@5) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843102c8 Data Size: 34407 Bytes = 33.6 KiB Architecture: ARM Hash algo: crc32 Hash value: d8a9f287 Hash algo: sha1 Hash value: ca425f024e3af1bcfc679d8c5409c542d186bc07 Image 6 (fdt@6) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84318a40 Data Size: 34547 Bytes = 33.7 KiB Architecture: ARM Hash algo: crc32 Hash value: 711c73d8 Hash algo: sha1 Hash value: 347ce97a2b403bb1d87023ce01c6cc07e2af5080 Image 7 (fdt@7) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84321244 Data Size: 38588 Bytes = 37.7 KiB Architecture: ARM Hash algo: crc32 Hash value: 9b9516a6 Hash algo: sha1 Hash value: 7d30817862d583b090c115f68fa6b4ab184c27e2 Image 8 (fdt@8) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8432aa10 Data Size: 38467 Bytes = 37.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 311234ec Hash algo: sha1 Hash value: c7be34f25ccb51f0d0eaa6985af77d30b872eaef Image 9 (fdt@9) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84334164 Data Size: 38165 Bytes = 37.3 KiB Architecture: ARM Hash algo: crc32 Hash value: dfaf8be6 Hash algo: sha1 Hash value: 1d0624d02a55608a2f590a8fa44719e2ba0b21e5 Default Configuration: 'config@1' Configuration 0 (config@1) Description: OpenWrt Kernel: kernel@1 FDT: fdt@1 Configuration 1 (config@2) Description: OpenWrt Kernel: kernel@1 FDT: fdt@2 Configuration 2 (config@3) Description: OpenWrt Kernel: kernel@1 FDT: fdt@3 Configuration 3 (config@4) Description: OpenWrt Kernel: kernel@1 FDT: fdt@4 Configuration 4 (config@5) Description: OpenWrt Kernel: kernel@1 FDT: fdt@5 Configuration 5 (config@6) Description: OpenWrt Kernel: kernel@1 FDT: fdt@6 Configuration 6 (config@7) Description: OpenWrt Kernel: kernel@1 FDT: fdt@7 Configuration 7 (config@8) Description: OpenWrt Kernel: kernel@1 FDT: fdt@8 Configuration 8 (config@9) Description: OpenWrt Kernel: kernel@1 FDT: fdt@9 ## Checking hash(es) for FIT Image at 84000000 ... Hash(es) for Image 0 (kernel@1): crc32+ sha1+ Hash(es) for Image 1 (fdt@1): crc32+ sha1+ Hash(es) for Image 2 (fdt@2): crc32+ sha1+ Hash(es) for Image 3 (fdt@3): crc32+ sha1+ Hash(es) for Image 4 (fdt@4): crc32+ sha1+ Hash(es) for Image 5 (fdt@5): crc32+ sha1+ Hash(es) for Image 6 (fdt@6): crc32+ sha1+ Hash(es) for Image 7 (fdt@7): crc32+ sha1+ Hash(es) for Image 8 (fdt@8): crc32+ sha1+ Hash(es) for Image 9 (fdt@9): crc32+ sha1+ ## Checking Image at 8433ffc0 ... Legacy image found Image Name: ARM OpenWrt Linux-3.14.77 Image Type: ARM Linux Kernel Image (lzma compressed) Data Size: 23986176 Bytes = 22.9 MiB Load Address: 40908000 Entry Point: 40908000 Verifying Checksum ... OK mmc_read will run command: mmc read 0x871cfca8 0x2a22 0x100 MMC read: dev # 0, block # 10786, count 256 ... 256 blocks read: OK boot partition : 1 MMC read: dev # 0, block # 17954, count 7680 ... 7680 blocks read: OK ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM OpenWrt Linux-3.14.77 Type: Kernel Image Compression: gzip compressed Data Start: 0x840000e4 Data Size: 3056294 Bytes = 2.9 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: e7747ae9 Hash algo: sha1 Hash value: 3ef2932a82d4bc46fd4600d69ca9b7b066b4fec9 Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt@1' FDT blob subimage Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx_cc device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842ea4d0 Data Size: 39067 Bytes = 38.2 KiB Architecture: ARM Hash algo: crc32 Hash value: f94716db Hash algo: sha1 Hash value: 7e37e5ed95940f74e51add9aab58a3766e853729 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x842ea4d0 Uncompressing Kernel Image ... OK Loading Device Tree to 871e3000, end 871ef89a ... OK Using machid 0x8010001 from environment Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 3.14.77 (jackie@TWTPEB2S1UB16) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r6043) ) #2 SMP PREEMPT Fri Oct 17 07:49:46 CST 2025 CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK04.1-C1 Flash name: EMMC Memory policy: Data cache writealloc PERCPU: Embedded 8 pages/cpu @dfbc7000 s8448 r8192 d16128 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 128768 Kernel command line: rootwait clk_ignore_unused user_debug=0xff PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 507984K/519168K available (4264K kernel code, 258K rwdata, 1348K rodata, 172K init, 356K bss, 11184K reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0208000 - 0xc0783500 (5614 kB) .init : 0xc0784000 - 0xc07af100 ( 173 kB) .data : 0xc07b0000 - 0xc07f0a78 ( 259 kB) .bss : 0xc07f0a78 - 0xc0849b40 ( 357 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Preemptible hierarchical RCU implementation. NR_IRQS:16 nr_irqs:16 16 Architected cp15 timer(s) running at 48.00MHz (virt). sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns Switching to timer-based delay loop Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x80213278 - 0x802132d0 CPU1: Booted secondary processor i2c devices info CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU2: Booted secondary processor i2c devices info CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 CPU3: Booted secondary processor i2c devices info CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 Brought up 4 CPUs SMP: Total of 4 processors activated (384.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 2048 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 2 hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 3 hw-breakpoint: CPU 2 failed to disable vector catch hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 Version Rollback Feature Disabled i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2 i2c i2c-0: Failed to register i2c client tlc59208f at 0x27 (-16) i2c i2c-0: Can't create device at 0x27 i2c i2c-0: Failed to register i2c client tlc59208f at 0x27 (-16) i2c i2c-0: Can't create device at 0x27 sps:sps is ready. bio: create slab <bio-0> at 0 SD0 VccQ: 1800 <--> 3000 mV usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb msm_bus_fabric_init_driver msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1 msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1 Neighbour init complete, with restricted-GC and GC-lock enabled 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0. msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready! msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0. msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initialized PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x40200000-0x402fffff] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0014[4] is all FFs PCI: bus0: Fast back to back transfers disabled pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 1:0x00 + 0x0014[4] is all FFs PCI: bus1: Fast back to back transfers disabled msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0028[4] is all FFs pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] msm_pcie_probe: msm_pcie_probe: RC0 is enabled in bootup Switched to clocksource arch_sys_counter NET: Registered protocol family 2 create ipmac proc TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available futex hash table entries: 1024 (order: 4, 65536 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 992 NET: Registered protocol family 38 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler noop registered io scheduler deadline registered (default) tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 tcsr 1953000.ess_tcsr: setting ess interface select = 0 tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled msm_serial_hsl_probe: detected port #0 (ttyMSM0) msm_serial_hsl_probe: Bus scaling is disabled 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM msm_hsl_console_setup: console setup on port #0 console [ttyMSM0] enabled msm_serial_hsl_init: driver initialized uart_tx_gpio is not available uart_rx_gpio is not available uart_cts_gpio is not available uart_rfr_gpio is not available Wakeup irq not specified. BLSP UART: Bus scaling is disabled. sps: BAM device 0x07884000 is not registered yet. sps:BAM 0x07884000 is registered. 78b0000.uart: ttyQHS0 at MMIO 0x78b0000 (irq = 140, base_baud = 460800) is a MSM HS UART qca_serial_hs module loaded sps:BAM 0x07884000 (va:0xe0b00000) enabled: ver:0x19, number of pipes:12 m25p80 spi0.0: Failed to find sector-size libphy: ipq40xx_mdio: probed ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered dwc3 8a00000.dwc3: no usb2 phy configured platform 8a00000.dwc3: Driver dwc3 requests probe deferral dwc3 6000000.dwc3: no usb2 phy configured platform 6000000.dwc3: Driver dwc3 requests probe deferral ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-platform: EHCI generic platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-platform: OHCI generic platform driver i2c /dev entries driver tlc59208f init! tlc59208f probe Init I2c register 27 i2c-core: driver [tlc59208f] using legacy suspend method i2c-core: driver [tlc59208f] using legacy resume method debug defined config_mmc_test in mmc_register_driver debug defined config_mmc_test in mmc_register_driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper sdhci_msm 7824900.sdhci: Got SD LDO GPIO #33 sdhci_msm 7824900.sdhci: Got CD GPIO #22. mmc0: no vmmc regulator found mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (7937 buckets, 31748 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered l2tp_core: L2TP core driver, V2.0 l2tp_netlink: L2TP netlink interface 8021q: 802.1Q VLAN Support v1.8 Registering SWP/SWPB emulation handler regulator-dummy: disabling mmc0: BKOPS_EN bit is not set mmc0: new HS200 MMC card at address 0001 mmcblk mmc0:0001: Card claimed for testing. debug mmc_bus_probe mmcblk0: mmc0:0001 4FPD3R 3.64 GiB mmcblk0boot0: mmc0:0001 4FPD3R partition 1 4.00 MiB mmcblk0boot1: mmc0:0001 4FPD3R partition 2 4.00 MiB mmcblk0rpmb: mmc0:0001 4FPD3R partition 3 512 KiB GPT:Primary header thinks Alt. header is not at the end of the disk. GPT:7405567 != 7634943 GPT:Alternate GPT header not at the end of the disk. GPT:7405567 != 7634943 GPT: Use GNU Parted to correct GPT errors. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 4. ART read (with data verification and return)... mmc_art_verify_read: the board_data is 110201 mmc0: Result: OK mmc0: Tests completed. mmc_dni_art_read_boot_part: rootfs part is #01 read_boot_part_from_art: the rootfs part num is #01 ART part: device [179:20] mmcblk0p20 set to be root filesystem #: vol name is 0:SBL1, start is 0x22, size is 0x400, ssz is 0x1 #: vol name is 0:BOOTCONFIG, start is 0x422, size is 0x400, ssz is 0x1 #: vol name is 0:QSEE, start is 0x822, size is 0x400, ssz is 0x1 #: vol name is 0:QSEE_ALT, start is 0xc22, size is 0x400, ssz is 0x1 #: vol name is 0:CDT, start is 0x1022, size is 0x200, ssz is 0x1 #: vol name is 0:CDT_ALT, start is 0x1222, size is 0x200, ssz is 0x1 #: vol name is 0:DDRPARAMS, start is 0x1422, size is 0x200, ssz is 0x1 #: vol name is 0:APPSBLENV, start is 0x1622, size is 0x200, ssz is 0x1 #: vol name is 0:APPSBL, start is 0x1822, size is 0x800, ssz is 0x1 #: vol name is 0:APPSBL_ALT, start is 0x2022, size is 0x800, ssz is 0x1 #: vol name is 0:ART, start is 0x2822, size is 0x200, ssz is 0x1 #: vol name is ARTMTD, start is 0x2a22, size is 0x200, ssz is 0x1 #: vol name is language, start is 0x2c22, size is 0x1000, ssz is 0x1 #: vol name is config, start is 0x3c22, size is 0x200, ssz is 0x1 #: vol name is pot, start is 0x3e22, size is 0x200, ssz is 0x1 #: vol name is traffic_meter, start is 0x4022, size is 0x200, ssz is 0x1 #: vol name is pot_bak, start is 0x4222, size is 0x200, ssz is 0x1 #: vol name is traffic_meter.bak, start is 0x4422, size is 0x200, ssz is 0x1 #: vol name is kernel, start is 0x4622, size is 0x1a00, ssz is 0x1 #: vol name is rootfs, start is 0x6022, size is 0x17600, ssz is 0x1 #: vol name is firmware, start is 0x4622, size is 0x19000, ssz is 0x1 #: vol name is mtdoops, start is 0x1d622, size is 0x200, ssz is 0x1 #: vol name is kernel-2, start is 0x1d822, size is 0x1a00, ssz is 0x1 #: vol name is rootfs-2, start is 0x1f222, size is 0x17600, ssz is 0x1 #: vol name is firmware-2, start is 0x1d822, size is 0x19000, ssz is 0x1 #: vol name is cert, start is 0x36822, size is 0x200, ssz is 0x1 #: vol name is device_table, start is 0x36a22, size is 0x2800, ssz is 0x1 #: vol name is circle, start is 0x39222, size is 0x18000, ssz is 0x1 #: vol name is streamboost, start is 0x51222, size is 0x19000, ssz is 0x1 #: vol name is forceshield, start is 0x6a222, size is 0xf000, ssz is 0x1 #: vol name is arlo, start is 0x79222, size is 0x2800, ssz is 0x1 #: vol name is rae, start is 0x7ba22, size is 0x1000, ssz is 0x1 #: vol name is armor, start is 0x7ca22, size is 0x19000, ssz is 0x1 #: vol name is ntgrcrydata, start is 0x95a22, size is 0x5000, ssz is 0x1 #: vol name is jdx, start is 0x9aa22, size is 0x200, ssz is 0x1 #: vol name is reserved, start is 0x9ac22, size is 0x23aaff, ssz is 0x1 mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 p34 p35 p36 mmcblk0boot1: unknown partition table mmcblk0boot0: unknown partition table xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: xHCI Host Controller usb usb1: Manufacturer: Linux 3.14.77 xhci-hcd usb usb1: SerialNumber: xhci-hcd.0.auto hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.14.77 xhci-hcd usb usb2: SerialNumber: xhci-hcd.0.auto hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000 usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.14.77 xhci-hcd usb usb3: SerialNumber: xhci-hcd.1.auto hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.14.77 xhci-hcd usb usb4: SerialNumber: xhci-hcd.1.auto hub 4-0:1.0: USB hub found hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) drivers/rtc/hctosys.c: unable to open rtc device (rtc0) clk: Not disabling unused clocks VFS: Mounted root (squashfs filesystem) readonly on device 179:20. Freeing unused kernel memory: 172K (c0784000 - c07af000) init: Console is alive init: - watchdog - random: kmodloader: uninitialized urandom read (4 bytes read, 45 bits of entropy available) init: - preinit - random: sh: uninitialized urandom read (4 bytes read, 59 bits of entropy available) random: procd: uninitialized urandom read (4 bytes read, 63 bits of entropy available) random: cat: uninitialized urandom read (4 bytes read, 69 bits of entropy available) random: mkdir: uninitialized urandom read (4 bytes read, 69 bits of entropy available) random: mkdir: uninitialized urandom read (4 bytes read, 69 bits of entropy available) random: grep: uninitialized urandom read (4 bytes read, 69 bits of entropy available) random: mktemp: uninitialized urandom read (4 bytes read, 69 bits of entropy available) random: mktemp: uninitialized urandom read (6 bytes read, 69 bits of entropy available) random: mktemp: uninitialized urandom read (4 bytes read, 69 bits of entropy available) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level Before mount_root Before DNI mount_root After DNI mount_root After mount_root procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. Thu Oct 16 23:50:12 UTC 2025 Checking env partition first ... /dev/mem opened. Memory mapped at address 0xb6fc4000. Value at address 0x102D000 (0xb6fc4000): 0x4801 Written 0x4902; readback 0x4902 /dev/mem opened. Memory mapped at address 0xb6fd4000. Value at address 0x102E000 (0xb6fd4000): 0x4801 Written 0x4902; readback 0x4902atherosgpio init /dev/mem opened. Memory mapped at address 0xb6f7f000. Value LED = 64, 63,54 ,53, 57,60 at address 0x103A000 (0xb6f7f000): 0x20C Written 0x4902; readback 0x4902 /dev/mem opened. Memory mapped at address 0xb6f05000. Value at address 0x103B000 (0xb6f05000): 0x208 Written 0x4902; readback 0x4902 The region number is: 0x0002 REGION: WW WPSPIN: 33598291 sn:4RPC7B5U00062 SN: 4RPC7B5U00062 lan mac: 8c:3b:ad:24:db:89 wlan 2g mac: 92:3b:ad:24:db:89 wan mac: 8c:3b:ad:24:db:8a wlan5g mac: 8c:3b:ad:24:db:8b wlan2nd5g mac: 8c:3b:ad:24:db:8c bt mac: 8c:3b:ad:24:db:8d hw_revision: Invalid MP FW version, please set in mp_fwversion Loading data from " config_dev " ... Done! The data center is Running ... random: nonblocking pool is initialized QCE50: __qce_init_clk: Unable to get CE core src clk, set to NULL qcrypto 8e20000.qcrypto: Qualcomm Crypto 5.3.1 device found @0x8e20000 qcrypto 8e20000.qcrypto: CE device = 0x0 , IO base, CE = 0xe1180000 , Consumer (IN) PIPE 2, Producer (OUT) PIPE 3 IO base BAM = 0x (null) BAM IRQ 239 Engines Availability = 0x2010453 sps:BAM 0x08e04000 is registered. sps:BAM 0x08e04000 (va:0xe11c0000) enabled: ver:0x27, number of pipes:4 QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000008e04000 irq 239 bus_scale_table is NULL qcrypto 8e20000.qcrypto: qcrypto-ecb-aes qcrypto 8e20000.qcrypto: qcrypto-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-ctr-aes qcrypto 8e20000.qcrypto: qcrypto-ecb-des qcrypto 8e20000.qcrypto: qcrypto-cbc-des qcrypto 8e20000.qcrypto: qcrypto-ecb-3des qcrypto 8e20000.qcrypto: qcrypto-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-xts-aes qcrypto 8e20000.qcrypto: qcrypto-sha1 qcrypto 8e20000.qcrypto: qcrypto-sha256 qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-hmac-sha1 qcrypto 8e20000.qcrypto: qcrypto-hmac-sha256 qcrypto 8e20000.qcrypto: qcrypto-aes-ccm qcrypto 8e20000.qcrypto: qcrypto-rfc4309-aes-ccm qcrypto: FIPS140-2 Known Answer Tests: Skipped clbr: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint client bridge loaded device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com loop: module loaded PPP generic driver version 2.4.2 ess-switch DT exist! switchreg_base_addr: 0xc000000 switchreg_size: 0x80000 switch_access_mode: local bus wan bmp:0x20 ess-psgmii DT exist! mac mode=0 current mac mode = 0 current dts led_source_num is 5 mdio DT exist! ssdk_plat_init start enable ess clk reset ok in probe! PHY ID is 0x4dd0b1 qca probe malibu phy driver succeeded! Dakota Chip version 0x1401 qca-ssdk module init succeeded! tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ********************************************************** * Driver :NSS GMAC Driver for RTL v(3.72a) * Version :1.0 * Copyright :Copyright (c) 2013-2016 The Linux Foundation. All rights reserved. ********************************************************** mdio bus 'mdio-gpio.0' get FAIL.netlink_kernel_create error ... qca-nss-drv.ko is loaded for symbol link dni-qos module init. gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) QCA Hy-Fi multicast installation successfully ip6_tables: (C) 2000-2006 Netfilter Core Team nf_conntrack_rtsp v0.6.21 loading nf_nat_rtsp v0.6.21 loading XHTTP netlink: create netlink OK. ip_set: protocol 6 NET: Registered protocol family 24 ECM init ECM database jhash random seed: 0xee775bc9 ECM init complete PPTP driver version 0.8.5 u32 classifier Performance counters on input device check on Actions configured Mirror/redirect action on Loading DNI-ENET driver Ebtables v2.0 registered l2tp_ppp: PPPoL2TP kernel driver, V2.0 ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 . = switch init . cfg02aa45 Config commit is not allowed during booting not need do overwrite lbd Also not need do overwrite lbd Also not need do overwrite lbd Also not need do overwrite lbd Also not need do overwrite DFS Config commit is not allowed during booting /etc/rc.common: /etc/rc.d/S11init-gpio: line 23: syntax error: unexpected "}" EXT4-fs (mmcblk0p35): mounted filesystem without journal. Opts: (null) bio: create slab <bio-1> at 1 EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) . = network init SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. device eth1 entered promiscuous mode init.enet: Default LAN MAC is : 8c:3b:ad:24:db:89 . Reading all physical volumes. This may take a while... Successfully initialized wpa_supplicant switch init SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. hyd: ERROR: Bridge is not attached; start hyfi-bridging first opmode = normal device eth1 left promiscuous mode br0: port 1(eth1) entered disabled state device eth1 entered promiscuous mode device eth0 entered promiscuous mode SSDK Init OK! operate done. SSDK Init OK! Illegal parameter(s) SSDK Init OK! operate done. . = net-lan init IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready =====before lan bridge down,should down backhaul ap ath01 first======= net.bridge.bridge-nf-call-custom = 0 hyfi_netlink_receive:108:hyfi: Not attached to bridge br0 Error running command br0: port 1(eth1) entered forwarding state br0: port 1(eth1) entered forwarding state net.bridge.bridge-nf-call-custom = 1 =====bridge up,should up backhaul ap ath01 first======= udhcp client (v0.9.8) started Sending discover... Sending discover... Sending discover... No lease, forking to background. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. hyd: starting daemon SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. EXT4-fs (mmcblk0p27): recovery complete EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts: (null) Run SATELLITE_BOARD net-scan config...The attached devices demo is Running ... Support ssdk switch mac table check function. The telnetenable is running ... . 16+0 records in 16+0 records out 261088 bytes (255.0KB) copied, 0.004306 seconds, 57.8MB/s 1+0 records in 1+0 records out 16384 bytes (16.0KB) copied, 0.000999 seconds, 15.6MB/s 1+0 records in 1+0 records out 16384 bytes (16.0KB) copied, 0.001347 seconds, 11.6MB/s mmc0: Starting tests of card mmc0:0001... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... Sending discover... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. 4096+0 records in 4096+0 records out 2097152 bytes (2.0MB) copied, 0.066260 seconds, 30.2MB/s Config commit is not allowed during booting mkdir: can't create directory '/tmp/router-analytics': File exists Cannot connect to server , will try 60s later!!time zone index is : 0 Run NTP Client with setting: pri:time-g.netgear.com sec:time-h.netgear.com Sending discover... net-scan backgroud start scan... [net-scan] start scan devices... [wlan]===time:Thu Oct 16 23:50:55 UTC 2025 command:wlan countrycode============== will set soap sync psk:f3a4e923c0a1d4daae329c82b397c157fdcf4523dd6d05451102e6517dc692a2 Config commit is not allowed during booting EXT4-fs (mmcblk0p35): mounted filesystem without journal. Opts: (null) Sending discover... [wlan]===time:Thu Oct 16 23:50:58 UTC 2025 command:wlan updateconf boot============== [wlan]=========time:Thu Oct 16 23:50:58 UTC 2025 wlan updateconf start====== bio: create slab <bio-1> at 1 EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (mmcblk0p35): mounted filesystem without journal. Opts: (null) bio: create slab <bio-1> at 1 EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) Init wifison script [net-scan]receive SIG10.. [wlan]=========time:Thu Oct 16 23:51:03 UTC 2025 wlan updateconf end====== QCA post_updateconf_qcawifi Config commit is not allowed during booting Config commit is not allowed during booting Config commit is not allowed during booting [wsplcd] Ignore wsplcd start before Soap sync net.bridge.bridge-nf-call-custom = 1 quagga.init: Starting zebra ... failed. quagga.init: Starting ripd ... failed. quagga.init: Starting ripngd ... failed. quagga.init: Starting watchquagga ... done. kcg 359 :GPL NetUSB up! INFO1ADF: NetUSB 1.12.16, 00030E4D : Nov 4 2021 04:46:40 INFO1AE1: 7423: RBR50 :RBR50 INFO1AE2: AUTH ISOC INFO1AE3: MOVE_HEAD emb_lp filterAudio INFO0789: 0 : tunnelID emusblp 0 INFO0789: 1 : tunnelID emusblp 1 INFO0789: 2 : tunnelID emusblp 2 INFO0789: 3 : tunnelID emusblp 3 INFO0789: 4 : tunnelID emusblp 4 INFO0789: 5 : tunnelID emusblp 5 INFO0789: 6 : tunnelID emusblp 6 INFO0789: 7 : tunnelID emusblp 7 INFO0789: 8 : tunnelID emusblp 8 INFO0789: 9 : tunnelID emusblp 9 Changing password for admin New password: INFO0AA2: --- checkSBusTimeoutThread start --- INFO0081: Add device intf dee0a800, dev dede1800 INFO054C: isHub usbcore: registered new interface driver KC NetUSB General Driver INFO1B4A: Reset device when disconnect INFO01D7: init proc : PAGE_SIZE 4096 INFO19D4: infomap bf87e3d8 INFO19D8: bndev : br0 INFO19DD: sleep to wait br0 to wake up INFO17C0: tcpConnector() started... : br0 [Bonjour] Interface: br0 is connected [KC] RBS50 IPP v1.5 Start (Jun 6 2017 17:15:40) traffic_meter start : Router mode, start trafficmeter. Retype password: $Shutting down igmpproxy: $Starting igmpproxy: ****** start ISP IPTV/VOD service with igmpproxy ****** SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. pgd = dc674000 [00000004] *pgd=9c57b831, *pte=00000000, *ppte=00000000 CPU: 1 PID: 6518 Comm: dal_ra Tainted: P 3.14.77 #2 task: dc59d580 ti: dc672000 task.ti: dc672000 PC is at 0xb6f13db0 LR is at 0x185f8 pc : [<b6f13db0>] lr : [<000185f8>] psr: 60000010 sp : bea77ca8 ip : 0003324c fp : bea77cbc r10: b6f71f70 r9 : 00000000 r8 : 00000000 r7 : 00000000 r6 : 00012cb8 r5 : 00000000 r4 : bea77f9b r3 : 00000000 r2 : 00000000 r1 : 00000001 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode USER_32 ISA ARM Segment user Control: 10c5387d Table: 9c67406a DAC: 00000015 CPU: 1 PID: 6518 Comm: dal_ra Tainted: P 3.14.77 #2 [<c021ea68>] (unwind_backtrace) from [<c021bb60>] (show_stack+0x10/0x14) [<c021bb60>] (show_stack) from [<c03b5780>] (dump_stack+0x78/0x98) [<c03b5780>] (dump_stack) from [<c02234b0>] (__do_user_fault+0x74/0xbc) [<c02234b0>] (__do_user_fault) from [<c022385c>] (do_page_fault+0x2f0/0x370) [<c022385c>] (do_page_fault) from [<c02083dc>] (do_DataAbort+0x34/0x98) [<c02083dc>] (do_DataAbort) from [<c02096f4>] (__dabt_usr+0x34/0x40) Exception stack(0xdc673fb0 to 0xdc673ff8) 3fa0: 00000000 00000001 00000000 00000000 3fc0: bea77f9b 00000000 00012cb8 00000000 00000000 00000000 b6f71f70 bea77cbc 3fe0: 0003324c bea77ca8 000185f8 b6f13db0 60000010 ffffffff restart the daemon telnetenable for Thin client !!! The telnetenable is running ... net.ipv4.neigh.default.gc_reap_limit = 100 restart klogd process [Orbi]***boot done*** [wifi-listener] Starting daemon [ arlo ] arlo list not found whc (repacd): starting WHC auto-configuration whc (repacd): Managed network: 0 whc (repacd): Device type: RE Sending discover... whc (repacd): Initialized 0 VAPs Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 6926,present: (config) [Bonjour] MDNS_CheckName: receive packet timeout [Bonjour] default device name = RBS50_8C-3B-AD-24-DB-89 [Bonjour] Answer Name Start (192.168.1.250) [KC] RBS50 Bonjour v1.9 Start (Jun 6 2017 17:17:49) Done! [REPACD-INIT] __repacd_config_re_mode whc (repacd): Using SON mode for NonCAP Sending discover... whc (repacd): Set VAP cfg0a3579 to Disabled=0 whc (repacd): Set VAP cfg143579 to Disabled=0 whc (repacd): Set VAP cfg063579 to Disabled=0 whc (repacd): Set VAP cfg083579 to Disabled=0 When run by root: smbpasswd [options] [username] otherwise: smbpasswd [options] options: -L local mode (must be first option) -h print this usage message -s use stdin for password prompt -c smb.conf file Use the given path to the smb.conf file -D LEVEL debug level -r MACHINE remote machine -U USER remote username (e.g. SAM/user) extra options when run by root or in local mode: -a add user -d disable user -e enable user -i interdomain trust account -m machine trust account -n set no password -W use stdin ldap admin password -w PASSWORD ldap admin password -x delete user -R ORDER name resolve order whc (repacd): Set VAP cfg0c3579 to Disabled=0 whc (repacd): Set VAP cfg0e3579 to Disabled=0 whc (repacd): Set VAP cfg103579 to Disabled=0 whc (repacd): Set VAP cfg123579 to Disabled=0 whc (repacd): Set radio wifi0 to QWrap DBDC Enabled=0 whc (repacd): Set radio wifi1 to QWrap Enabled=0 whc (repacd): Set radio wifi2 to QWrap Enabled=0 whc (repacd): Set iface cfg063579 to WDS=1 whc (repacd): Set iface cfg063579 to QWrapAP=0 whc (repacd): Set iface cfg063579 to BlockDFSChan=0 whc (repacd): Set iface cfg063579 to ExtAP=0 Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 7443,present: (config) Done! whc (repacd): Set iface cfg063579 to RootDistance=255 whc (repacd): Set iface cfg083579 to QWrapAP=0 whc (repacd): Set iface cfg083579 to BlockDFSChan=0 whc (repacd): Set iface cfg083579 to RRM=1 whc (repacd): Set iface cfg083579 to ExtAP=0 whc (repacd): Set iface cfg0a3579 to ExtAP=0 Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 7457,present: (config) When run by root: smbpasswd [options] [username] otherwise: smbpasswd [options] options: -L local mode (must be first option) -h print this usage message -s use stdin for password prompt -c smb.conf file Use the given path to the smb.conf file -D LEVEL debug level -r MACHINE remote machine -U USER remote username (e.g. SAM/user) extra options when run by root or in local mode: -a add user -d disable user -e enable user -i interdomain trust account -m machine trust account -n set no password -W use stdin ldap admin password -w PASSWORD ldap admin password -x delete user -R ORDER name resolve order Done! whc (repacd): Set iface cfg0a3579 to BSSID=00:00:00:00:00:00 whc (repacd): Set iface cfg0a3579 to RE_ScalingFactor=85 Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 7644,present: (config) Done! whc (repacd): Set iface cfg0a3579 to caprssi=30 Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 7697,present: (config) Done! whc (repacd): Set iface cfg0a3579 to RootDistance=255 whc (repacd): Set iface cfg0c3579 to WDS=1 whc (repacd): Set iface cfg0c3579 to QWrapAP=0 whc (repacd): Set iface cfg0c3579 to BlockDFSChan=0 whc (repacd): Set iface cfg0c3579 to ExtAP=0 Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 7729,present: (config) Done! whc (repacd): Set iface cfg0c3579 to RootDistance=255 whc (repacd): Set iface cfg0e3579 to WDS=1 whc (repacd): Set iface cfg0e3579 to QWrapAP=0 whc (repacd): Set iface cfg0e3579 to BlockDFSChan=0 whc (repacd): Set iface cfg0e3579 to ExtAP=0 Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 7755,present: (config) Done! whc (repacd): Set iface cfg0e3579 to RootDistance=255 whc (repacd): Set iface cfg103579 to WDS=1 whc (repacd): Set iface cfg103579 to QWrapAP=0 whc (repacd): Set iface cfg103579 to BlockDFSChan=0 whc (repacd): Set iface cfg103579 to ExtAP=0 Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 7782,present: (config) Done! whc (repacd): Set iface cfg103579 to RootDistance=255 whc (repacd): Set iface cfg123579 to QWrapAP=0 whc (repacd): Set iface cfg123579 to BlockDFSChan=0 whc (repacd): Set iface cfg123579 to RRM=1 whc (repacd): Set iface cfg123579 to ExtAP=0 whc (repacd): Set iface cfg143579 to ExtAP=0 whc (repacd): Set iface cfg143579 to RE_ScalingFactor=85 Saving Data... from parentid: 6706, parent process: (S98repacd),presentid: 7819,present: (config) Done! whc (repacd): Set iface cfg143579 to RootDistance=255 whc (repacd): Station device list = wifi0 wifi2 Sending discover... whc (repacd): Set wsplcd to ENROLLEE mode whc (repacd): Set wsplcd DeepCloneNoBSSID=1 whc (repacd): Set wsplcd ManageVAPInd=0 whc (repacd): Restarting network stack... [wlan]===time:Thu Oct 16 23:51:19 UTC 2025 command:wlan down============== [wlan]=========time:Thu Oct 16 23:51:19 UTC 2025 wlan down start================== Saving Data... from parentid: 8253, parent process: (wlan),presentid: 9169,present: (config) Done! qcawifi disable radio wifi0 qcawifi disable radio wifi1 qcawifi disable radio wifi2 [wlan]=========time:Thu Oct 16 23:51:24 UTC 2025 wlan down end================== [wlan]=========time:Thu Oct 16 23:51:24 UTC 2025 wlan post down ================== net.bridge.bridge-nf-call-custom = 1 hyd: some interface(s) are not ready. hyd: ERROR: Private network interface checking failed Sending discover... [wlan]===time:Thu Oct 16 23:51:30 UTC 2025 command:wlan up============== [wlan]=========time:Thu Oct 16 23:51:30 UTC 2025 wlan up start================== Sending discover... Saving Data... from parentid: 10173, parent process: (wlan),presentid: 10905,present: (config) Done! qcawifi: enable radio wifi0 Sending discover... __mm_init_module ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_spectral: Version 2.0.0 Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_tx99: Version 2.0 Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_da_pci: (Atheros/multi-bss) *********** IPQ4019 *************Wifi0 CPU frequency 250000000 hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn d9f804c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type b __ol_ath_attach: dev name wifi0 ol_ath_attach interface_id 0 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xb, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3803] Get Caldata for wifi0. qdf_fs_read[59], Open File /tmp/wifi0.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 2536file size:12064=====checksum:0==== qc98xx_verify_checksum: flash checksum passed: 0x5b11 ol_transfer_bin_file 3879: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 4680 First OTP send param 8000 ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660 ol_ath_download_firmware:##Board Id 20 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi0: Selecting board data file name boardData_1_0_IPQ4019_DK04_2G.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_2G.bin ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 4680 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1610612717 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:100109 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 162035 Target address 417c80 scn=d9f804c0 target_write_addr=417c80 seg_info=debf5410 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 1, Download data len 368384 ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle dec32000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :d9c30000-htc_create: (0xde93e800) htc_wmi_init() HT Create . de93e800 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xd9c34578hif_completion_thread_startup: pipe_num:3 pipe_info:0xd9c34650hif_completion_thread_startup: pipe_num:4 pipe_info:0xd9c34698 -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev d90c8000 hrtimer d90cc890 htt_alloc_peer_map_mem : Alloc Success : host q vaddr d942a000 paddr 9942a000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d8d40000 Firmware_Build_Number:14 FW wireless modes: 0x680c num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa btcoex_support 1, wlan_prio_gpio 52, coex_gpio_pin 0 0 0 wmi_service_coex_gpio 1, wmi_service_4_wire_coex_support 1, coex_version 2 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 52 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, idx 6 req 5 num_units 0 num_unit_info 2 unit size 2044 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2044, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x99f64000 chunk 1 len 54272 requested , ptr 0x98d30000 chunk 2 len 217088 requested , ptr 0x98dc0000 chunk 3 len 395064 requested , ptr 0x98e00000 chunk 4 len 107520 requested , ptr 0x98da0000 chunk 5 len 6144 requested , ptr 0x9c534000 chunk 6 len 1085364 requested , ptr 0x98800000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 0 ol_ath_attach() connect HTC. bypasswmi : 0 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: 2884: Netlink socket created:dc44e400 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_attach: called; ptr=d894198c, radar_info=dd6c1c30 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[1] ..ptr:bfa07b90 ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =dd322a00 ic->ic_wrap_com=dd322a00 &wrap_com->wc_devt=dd322a00 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_ahb_probe num_radios=0, wifi_radios[0].sc = d9f804c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr *********** IPQ4019 *************Wifi1 CPU frequency 250000000 hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn d8f004c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type b __ol_ath_attach: dev name wifi1 ol_ath_attach interface_id 1 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xb, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3803] Get Caldata for wifi1. qdf_fs_read[59], Open File /tmp/wifi1.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 2539file size:12064=====checksum:0==== qc98xx_verify_checksum: flash checksum passed: 0xb6e2 ol_transfer_bin_file 3879: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 4680 First OTP send param 8000 ol_ath_download_firmware :First OTP download and Execute is good address:0x5400 return param 4660 ol_ath_download_firmware:##Board Id 21 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi1: Selecting board data file name boardData_1_0_IPQ4019_DK04_5G.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_5G.bin ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 4680 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:100109 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 162035 Target address 417c80 scn=d8f004c0 target_write_addr=417c80 seg_info=dc462410 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 1, Download data len 368384 ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle d942e000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :d8ec8000-htc_create: (0xdd1a5800) htc_wmi_init() HT Create . dd1a5800 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xd8ecc578hif_completion_thread_startup: pipe_num:3 pipe_info:0xd8ecc650hif_completion_thread_startup: pipe_num:4 pipe_info:0xd8ecc698 -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev d8618000 hrtimer d861c890 htt_alloc_peer_map_mem : Alloc Success : host q vaddr ddc8c000 paddr 9dc8c000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d82a0000 Firmware_Build_Number:14 FW wireless modes: 0x1f9001 num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, idx 6 req 5 num_units 0 num_unit_info 2 unit size 2044 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2044, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x9c7a8000 chunk 1 len 54272 requested , ptr 0x98960000 chunk 2 len 217088 requested , ptr 0x98300000 chunk 3 len 395064 requested , ptr 0x98380000 chunk 4 len 107520 requested , ptr 0x98360000 chunk 5 len 6144 requested , ptr 0x9ead8000 chunk 6 len 1085364 requested , ptr 0x97c00000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1 target uses HTT version 2.2; host uses 2.2 ol_ath_attach() connect HTC. bypasswmi : 0 ol_ath_attach: low_5ghz: 5150 high_5gh: 5330 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Add VHT80 channel: 5690 Add VHT80 channel: 5775 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=58 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: Offload using existing sock dc44e400 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_attach: called; ptr=d89d998c, radar_info=dd6c1c30 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[2] ..ptr:bfa07b90 ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =d9412c00 ic->ic_wrap_com=d9412c00 &wrap_com->wc_devt=d9412c00 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_ahb_probe num_radios=1, wifi_radios[1].sc = d8f004c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr ath_ol_pci: (Atheros/multi-bss) hif_pci_enable_bus: con_mode = 0x0, device_id = 0x46PCI: enabling device 0000:00:00.0 (0144 -> 0147) PCI: enabling device 0000:01:00.0 (0140 -> 0142) hif_pci_enable_bus: hif_enable_pci done *********** QCA9984 *************hif_pci_enable_bus: hif_type = 0xc, target_type = 0xahif_pci_enable_bus: hif_pci_probe_tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW signal, retries = 0hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_set_hia_extnd: E chip_id 0xa chip_revision 0x0 CLOCK PLL skipped hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL hif_set_hia_extnd: targ_clk is not provided, skipping pre-configuring PLL hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn d7e404c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type a __ol_ath_attach: dev name wifi2 ol_ath_attach interface_id 2 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xa, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3803] Get Caldata for wifi2. qdf_fs_read[59], Open File /tmp/wifi2.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 2542file size:12064=====checksum:0==== qc98xx_verify_checksum: flash checksum passed: 0x80fd ol_transfer_bin_file 3879: Download Flash data len 12064 Board extended Data download address: 0x0 Switching to Tx Mode-1 Threshold 280 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 9024 First OTP send param 8000 ol_ath_download_firmware :First OTP download and Execute is good address:0x1800 return param 4660 ol_ath_download_firmware:##Board Id 6 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9984/hw.1/boardData_QCA9984_CUS239_high_band_5G_v1_006.bin ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 9024 Switching to Tx Mode-1 Threshold 280 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:26616 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 235528 Target address 423408 scn=d7e404c0 target_write_addr=423408 seg_info=dd263b10 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=QCA9984/hw.1/athwlan.bin swap_filename=/lib/firmware/QCA9984/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: QCA9984/hw.1/athwlan.bin ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 1, Download data len 379056 ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle d8eee000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :d7d68000-htc_create: (0xdd1a4800) htc_wmi_init() HT Create . dd1a4800 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xd7d6c578hif_completion_thread_startup: pipe_num:3 pipe_info:0xd7d6c650hif_completion_thread_startup: pipe_num:4 pipe_info:0xd7d6c698 -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev d7be8000 hrtimer d7bec890 htt_alloc_peer_map_mem : Alloc Success : host q vaddr d7430000 paddr 97430000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d7060000 Firmware_Build_Number:14 FW wireless modes: 0x7f9001 num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339b79fa vht_supp_mcs:0x0000ffaa wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 2216 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 2216, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 12288 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 12288, idx 6 req 5 num_units 0 num_unit_info 2 unit size 1980 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 1980, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x97ec8000 chunk 1 len 54272 requested , ptr 0x970c0000 chunk 2 len 217088 requested , ptr 0x97100000 chunk 3 len 1176696 requested , ptr 0x97200000 chunk 4 len 107520 requested , ptr 0x97320000 chunk 5 len 12288 requested , ptr 0x97350000 chunk 6 len 1051380 requested , ptr 0x96c00000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 2 ol_ath_attach() connect HTC. bypasswmi : 0 ol_ath_attach: low_5ghz: 5490 high_5gh: 5850 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Add VHT80 channel: 5690 Add VHT80 channel: 5775 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === Skipping VHT80 channel 5825 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === freq=106 freq=122 freq=138 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: Offload using existing sock dc44e400 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_if_dfs_attach: called; ptr=d7db198c, radar_info=dd6c1c10 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[3] ..ptr:bfa07b90 ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =dd26e800 ic->ic_wrap_com=dd26e800 &wrap_com->wc_devt=dd26e800 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_pci_probe num_radios=2, wifi_radios[2].sc = d7e404c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback __sa_init_module No Direct-Attach chipsets found. Removing athdebug proc file ath_dev: driver unloaded ath_tx99: driver unloaded ath_rate_atheros: driver unloaded ath_hal: driver unloaded isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 wlan_vap_create : enter. devhandle=0xd9f804c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 92:3b:ad:24:db:89: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd9f804c0, vap=0xd9dc8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling TSO bit for the vap ath0 features 4000 Enabling LRO bit for the vap ath0 features 4000 VAP device ath0 created osifp: (dd1a24c0) os_if: (d9dc8000) siwfreq Set freq vap 0 stop send + d9dc8000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12241 Comm:iwconfig :: PPID:11015 Comm:wlan <=< Set freq vap 0 stop send -d9dc8000 Set wait done --d9dc8000 ME Pool succesfully initialized vaddr - d6dc0000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-0(ath0):set SIOC80211NWID, 2 characters DES SSID SET=on vap-0(ath0):set SIOC80211NWID, 6 characters DES SSID SET=ORBI37 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0007020000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath0 entered promiscuous mode Sending discover... ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2138 Comm:hostapd :: PPID:1 Comm:procd <=< Sending SCAN START cmd br0: port 3(ath0) entered forwarding state br0: port 3(ath0) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath0 OK ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9545fc arg=d8920000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9dc8000 send_vdev_down_cmd_non_tlv for vap 0 (dec32000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12360 Comm:iwpriv :: PPID:11015 Comm:wlan <=< Sending SCAN START cmd wlan_vap_create : enter. devhandle=0xd9f804c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 1 Type = 1, Subtype = 0 VAP Addr = 96:3b:ad:24:db:89: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd9f804c0, vap=0xd6d18000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath01 features 4000 Enabling SG bit for the vap ath01 features 4000 Enabling SG bit for the vap ath01 features 4000 Enabling TSO bit for the vap ath01 features 4000 Enabling LRO bit for the vap ath01 features 4000 VAP device ath01 created osifp: (de93d4c0) os_if: (d6d18000) siwfreq Set freq vap 0 stop send + d9dc8000 ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9545fc arg=d8920000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xd9dc8000 send_vdev_down_cmd_non_tlv for vap 0 (dec32000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12386 Comm:iwconfig :: PPID:11015 Comm:wlan <=< Set freq vap 0 stop send -d9dc8000 Set wait done --d9dc8000 Set freq vap 1 stop send + d6d18000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12386 Comm:iwconfig :: PPID:11015 Comm:wlan <=< Set freq vap 1 stop send -d6d18000 Set wait done --d6d18000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12386 Comm:iwconfig :: PPID:11015 Comm:wlan <=< Sending SCAN START cmd ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9545fc arg=d8920000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9dc8000 Switching to Tx Mode-1 Threshold 280 send_vdev_down_cmd_non_tlv for vap 0 (dec32000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12419 Comm:iwpriv :: PPID:11015 Comm:wlan <=< Sending SCAN START cmd vap-1(ath01):set SIOC80211NWID, 2 characters DES SSID SET=on vap-1(ath01):set SIOC80211NWID, 21 characters DES SSID SET=NETGEAR_ORBI_hidden76 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0407020000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 device ath01 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath01 DEVICE IS DOWN ifname=ath01 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd6d18000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2138 Comm:hostapd :: PPID:1 Comm:procd <=< br0: port 4(ath01) entered forwarding state br0: port 4(ath01) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath01 OK osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd6d18000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12555 Comm:iwpriv :: PPID:11015 Comm:wlan <=< wlan_vap_create : enter. devhandle=0xd9f804c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 2 Type = 1, Subtype = 0 VAP Addr = 9a:3b:ad:24:db:89: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd9f804c0, vap=0xd7340000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath03 features 4000 Enabling SG bit for the vap ath03 features 4000 Enabling SG bit for the vap ath03 features 4000 Enabling TSO bit for the vap ath03 features 4000 Enabling LRO bit for the vap ath03 features 4000 VAP device ath03 created osifp: (dde21cc0) os_if: (d7340000) siwfreq Set freq vap 0 stop send + d9dc8000 ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9545fc arg=d8920000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xd9dc8000 send_vdev_down_cmd_non_tlv for vap 0 (dec32000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12575 Comm:iwconfig :: PPID:11015 Comm:wlan <=< Sending discover... Set freq vap 0 stop send -d9dc8000 Set wait done --d9dc8000 Set freq vap 1 stop send + d6d18000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12575 Comm:iwconfig :: PPID:11015 Comm:wlan <=< Set freq vap 1 stop send -d6d18000 Set wait done --d6d18000 Set freq vap 2 stop send + d7340000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12575 Comm:iwconfig :: PPID:11015 Comm:wlan <=< Set freq vap 2 stop send -d7340000 Set wait done --d7340000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12575 Comm:iwconfig :: PPID:11015 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd6d18000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12575 Comm:iwconfig :: PPID:11015 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9545fc arg=d8920000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9dc8000 send_vdev_down_cmd_non_tlv for vap 0 (dec32000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12589 Comm:iwpriv :: PPID:11015 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd6d18000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12589 Comm:iwpriv :: PPID:11015 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9545fc arg=d8920000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9dc8000 send_vdev_down_cmd_non_tlv for vap 0 (dec32000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12595 Comm:iwpriv :: PPID:11015 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd6d18000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12595 Comm:iwpriv :: PPID:11015 Comm:wlan <=< WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-2(ath03):set SIOC80211NWID, 2 characters DES SSID SET=on vap-2(ath03):set SIOC80211NWID, 13 characters DES SSID SET=NETGEAR-Guest ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0007020000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath03 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath03 DEVICE IS DOWN ifname=ath03 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd7340000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2138 Comm:hostapd :: PPID:1 Comm:procd <=< br0: port 5(ath03) entered forwarding state br0: port 5(ath03) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath03 OK osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd7340000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:12720 Comm:iwpriv :: PPID:11015 Comm:wlan <=< wlan_vap_create : enter. devhandle=0xd9f804c0, opmode=IEEE80211_M_STA, flags=0x3 send_vdev_create_cmd_non_tlv: ID = 3 Type = 2, Subtype = 0 VAP Addr = 9e:3b:ad:24:db:89: send_set_ps_mode_cmd_non_tlv:set psmode=1 wlan_vap_create : exit. devhandle=0xd9f804c0, vap=0xd70f0000, opmode=IEEE80211_M_STA, flags=0x3. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath02 features 4000 Enabling SG bit for the vap ath02 features 4000 Enabling SG bit for the vap ath02 features 4000 Enabling TSO bit for the vap ath02 features 4000 Enabling LRO bit for the vap ath02 features 4000 VAP device ath02 created osifp: (dd3354c0) os_if: (d70f0000) siwfreq send_set_ps_mode_cmd_non_tlv:set psmode=0 send_set_ps_mode_cmd_non_tlv:set psmode=0 vap-3(ath02):set SIOC80211NWID, 2 characters DES SSID SET=on vap-3(ath02):set SIOC80211NWID, 21 characters DES SSID SET=NETGEAR_ORBI_hidden76 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 1 su bfer 1 mu bfer 0 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 1 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 0146c Private capibility_data : 0407020000000000 -----su bfee 0 mu bfee 1 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 1 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 1 su bfer 1 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 1 su bfer 1 mu bfer 0 impl bf 0 sounding dim 1 device ath02 entered promiscuous mode ieee80211_ucfg_getparam : parameter 0x284 not supported br0: port 6(ath02) entered forwarding state br0: port 6(ath02) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath02 Sending discover... Cannot connect to server , will try 60s later!!br0: port 6(ath02) entered disabled state OK send_vdev_down_cmd_non_tlv for vap 0 (dec32000) OL vap_start + VDEV START OL vap_start - OL vap_start + VDEV START OL vap_start - Sending SCAN START cmd OL vap_start + VDEV START OL vap_start - vap0: Init in progress. Delay vap_stop vap0: Init in progress. Delay vap_stop vap0: Init in progress. Delay vap_stop vap0: Init in progress. Delay vap_stop vap0: Init in progress. Delay vap_stop vap0: Init in progress. Delay vap_stop vap0: Init in progress. Delay vap_stop vap0: Init in progress. Delay vap_stop ol_vdev_start_resp_ev for vap 0 (dec32000) send_wmm_update_cmd_non_tlv: vap0: Init in progress. Delay vap_stop Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:13116 Comm:button_detect :: PPID:6352 Comm:button_detect <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (dec32000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_vdev_start_resp_ev for vap 1 (dec32000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:13116 Comm:button_detect :: PPID:6352 Comm:button_detect <=< su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 1 (dec32000) ol_vdev_start_resp_ev for vap 2 (dec32000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:13116 Comm:button_detect :: PPID:6352 Comm:button_detect <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 2 (dec32000) osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xd9dc8000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:13074 Comm:ifconfig :: PPID:11015 Comm:wlan <=< STOPPED EVENT for vap 0 (dec32000) send_vdev_down_cmd_non_tlv for vap 0 (dec32000) br0: port 3(ath0) entered disabled state osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9dc8000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:13117 Comm:ifconfig :: PPID:11015 Comm:wlan <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (dec32000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/0 :: PPID:0 Comm:swapper/0 <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (dec32000) ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 br0: port 3(ath0) entered forwarding state br0: port 3(ath0) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath0 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xd7340000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:13166 Comm:ifconfig :: PPID:11015 Comm:wlan <=< STOPPED EVENT for vap 2 (dec32000) send_vdev_down_cmd_non_tlv for vap 2 (dec32000) br0: port 5(ath03) entered disabled state The extender led demo is Running ... qcawifi: enable radio wifi1 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=58 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 wlan_vap_create : enter. devhandle=0xd8f004c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 8c:3b:ad:24:db:8b: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd8f004c0, vap=0xd6e48000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling TSO bit for the vap ath1 features 4000 Enabling LRO bit for the vap ath1 features 4000 VAP device ath1 created osifp: (d73e24c0) os_if: (d6e48000) siwfreq Set freq vap 0 stop send + d6e48000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:13439 Comm:iwconfig :: PPID:13297 Comm:wlan <=< Set freq vap 0 stop send -d6e48000 Set wait done --d6e48000 ME Pool succesfully initialized vaddr - d6e80000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-0(ath1):set SIOC80211NWID, 2 characters DES SSID SET=on vap-0(ath1):set SIOC80211NWID, 6 characters DES SSID SET=ORBI37 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0007020000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath1 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 DEVICE IS DOWN ifname=ath1 DEVICE IS DOWN ifname=ath1 hyd: some interface(s) are not ready. hyd: ERROR: Private network interface checking failed Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2138 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (d942e000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/3 :: PPID:1 Comm:procd <=< Sending discover... su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (d942e000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 7(ath1) entered forwarding state br0: port 7(ath1) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath1 OK wlan_vap_create : enter. devhandle=0xd8f004c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 1 Type = 1, Subtype = 0 VAP Addr = 92:3b:ad:24:db:8b: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd8f004c0, vap=0xd6ea8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath11 features 4000 Enabling SG bit for the vap ath11 features 4000 Enabling SG bit for the vap ath11 features 4000 Enabling TSO bit for the vap ath11 features 4000 Enabling LRO bit for the vap ath11 features 4000 VAP device ath11 created osifp: (de93fcc0) os_if: (d6ea8000) siwfreq Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:13698 Comm:iwpriv :: PPID:13297 Comm:wlan <=< vap 0: drop SWBA event, since vap is not active STOPPED EVENT for vap 0 (d942e000) send_vdev_down_cmd_non_tlv for vap 0 (d942e000) OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (d942e000) Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:13698 Comm:iwpriv :: PPID:13297 Comm:wlan <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (d942e000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-1(ath11):set SIOC80211NWID, 2 characters DES SSID SET=on vap-1(ath11):set SIOC80211NWID, 13 characters DES SSID SET=NETGEAR-Guest ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0007020000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath11 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath11 DEVICE IS DOWN ifname=ath11 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2138 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 1 (d942e000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:2138 Comm:hostapd :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 1 (d942e000) ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 8(ath11) entered forwarding state br0: port 8(ath11) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath11 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:13791 Comm:ifconfig :: PPID:13297 Comm:wlan <=< STOPPED EVENT for vap 1 (d942e000) send_vdev_down_cmd_non_tlv for vap 1 (d942e000) br0: port 8(ath11) entered disabled state qcawifi: enable radio wifi2 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === Skipping VHT80 channel 5660 Skipping VHT80 channel 5680 Skipping VHT80 channel 5700 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === freq=106 freq=122 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 Sending discover... wlan_vap_create : enter. devhandle=0xd7e404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 8c:3b:ad:24:db:8c: su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 1 sounding dim 0 ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd7e404c0, vap=0xd6f98000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling TSO bit for the vap ath2 features 4000 Enabling LRO bit for the vap ath2 features 4000 VAP device ath2 created osifp: (dd336cc0) os_if: (d6f98000) siwfreq Set freq vap 0 stop send + d6f98000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:14005 Comm:iwconfig :: PPID:13893 Comm:wlan <=< Set freq vap 0 stop send -d6f98000 Set wait done --d6f98000 vap-0(ath2):set SIOC80211NWID, 2 characters DES SSID SET=on vap-0(ath2):set SIOC80211NWID, 21 characters DES SSID SET=NETGEAR_ORBI_hidden76 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 3 : 00146c Private capibility_data : 040702su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 0000000000 ---------------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 device ath2 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 DEVICE IS DOWN ifname=ath2 DEVICE IS DOWN ifname=ath2 2.4G_backhaul_disconnected... flow soap start action= now...... Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2138 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (d8eee000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 9(ath2) entered forwarding state br0: port 9(ath2) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath2 OK Sending discover... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd wlan_vap_create : enter. devhandle=0xd7e404c0, opmode=IEEE80211_M_STA, flags=0x3 send_vdev_create_cmd_non_tlv: ID = 1 Type = 2, Subtype = 0 VAP Addr = 92:3b:ad:24:db:8c: send_set_ps_mode_cmd_non_tlv:set psmode=1 wlan_vap_create : exit. devhandle=0xd7e404c0, vap=0xd68c0000, opmode=IEEE80211_M_STA, flags=0x3. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath21 features 4000 Enabling SG bit for the vap ath21 features 4000 Enabling SG bit for the vap ath21 features 4000 Enabling TSO bit for the vap ath21 features 4000 Enabling LRO bit for the vap ath21 features 4000 VAP device ath21 created osifp: (d9f184c0) os_if: (d68c0000) siwfreq send_set_ps_mode_cmd_non_tlv:set psmode=0 send_set_ps_mode_cmd_non_tlv:set psmode=0 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 1 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 1 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 0146c Private capibility_data : 0407020000000000 ---------------------------------------- su bfee 0 mu bfee 1 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 1 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 1 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3 su bfee 1 mu bfee 1 su bfer 1 mu bfer 0 impl bf 0 sounding dim 3 device ath21 entered promiscuous mode ieee80211_ucfg_getparam : parameter 0x284 not supported br0: port 10(ath21) entered forwarding state br0: port 10(ath21) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath21 br0: port 10(ath21) entered disabled state OK The 5G extender led demo is Running ... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd iface_mgr: ifacemgr_load_conf_file: 218: No STA VAPs are configured 92:3b:ad:24:db:89 92:3b:ad:24:db:89 8c:3b:ad:24:db:8c 8c:3b:ad:24:db:8c Its a Repeater! iface_mgr: ifacemgr_conn_to_global_wpa_s: 248: connected to global wpa_s iface_mgr: ifacemgr_display_updated_config: 560: Mode:3 timeout:60 [wlan]=========time:Thu Oct 16 23:52:14 UTC 2025 wlan up end================== QCA post_lock_qcawifi Restart wsplcd after wlan up [WSPLCD init] After updateconf lock check [wsplcd] Ignore wsplcd start before Soap sync Restart hyd after wlan up Saving Data... from parentid: 15201, parent process: (wifison.sh),presentid: 15736,present: (config) Done! ME Pool succesfully initialized vaddr - d6660000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Performing a DHCP renew Sending discover... Kick_backhaul... 5G_backhaul_disconnected... flow soap start action= now...... hyd: starting daemon Sending discover... ath0 IEEE 802.11ng ESSID:"ORBI37" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden76" ath02 IEEE 802.11b ESSID:"NETGEAR_ORBI_hidden76" ath1 IEEE 802.11ac ESSID:"ORBI37" ath03 IEEE 802.11ng ESSID:"NETGEAR-Guest" ath11 IEEE 802.11ac ESSID:"NETGEAR-Guest" ath2 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden76" ath21 IEEE 802.11ac ESSID:"" [ath0] Band steering events being sent to PID:17177 [ath01] Band steering events being sent to PID:17177 [ath02] Band steering events being sent to PID:17177 [ath1] Band steering events being sent to PID:17177 [ath2] Band steering events being sent to PID:17177 [ath21] Band steering events being sent to PID:17177 [ath0] Band steering events being sent to PID:17177 [ath1] Band steering events being sent to PID:17177 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 8c:3b:ad:24:db:89 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 8c:3b:ad:24:db:89 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 8c:3b:ad:24:db:89 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 8c:3b:ad:24:db:89 Sending SCAN START cmd Sending discover... hyd: starting daemon [wlan]=========time:Thu Oct 16 23:52:25 UTC 2025 wlan post up ================== [wlan]========= reload netscan ================== net.bridge.bridge-nf-call-custom = 1 not restart eth_handle when /tmp/disable_satelite_dhcpd existed ath0 IEEE 802.11ng ESSID:"ORBI37" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden76" ath02 IEEE 802.11b ESSID:"NETGEAR_ORBI_hidden76" ath1 IEEE 802.11ac ESSID:"ORBI37" ath03 IEEE 802.11ng ESSID:"NETGEAR-Guest" ath11 IEEE 802.11ac ESSID:"NETGEAR-Guest" ath2 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden76" ath21 IEEE 802.11ac ESSID:"" send_vdev_down_cmd_non_tlv for vap 3 (dec32000) hyd: starting daemon [ath0] Band steering events being sent to PID:19409 [ath01] Band steering events being sent to PID:19409 [ath02] Band steering events being sent to PID:19409 [ath1] Band steering events being sent to PID:19409 [ath2] Band steering events being sent to PID:19409 [ath21] Band steering events being sent to PID:19409 [ath0] Band steering events being sent to PID:19409 [ath1] Band steering events being sent to PID:19409 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 8c:3b:ad:24:db:89 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 8c:3b:ad:24:db:89 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 8c:3b:ad:24:db:89 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr 8c:3b:ad:24:db:89 Sending SCAN START cmd Sending discover... Sending discover... Sending discover... [WSPLCD init] After updateconf lock check [wsplcd] Ignore wsplcd start before Soap sync repacd: checking backhaul_ap interface --> network:0 - iface:ath0 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath01 - disabled:0 - mode:ap - device:wifi0 - baOrbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20403 Comm:ifconfig :: PPID:6706 Comm:S98repacd <=< ckhaul_ap:1 repacd: checking backhaul_ap interface --> networkSTOPPED EVENT for vap 0 (d8eee000) :0 - iface:ath02 - disabled:0 - mode:sta - device:wifi0 - backhasend_vdev_down_cmd_non_tlv for vap 0 (d8eee000) ul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath1 - disabled:0 - mode:ap - device:wifi1 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath03 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:0 rebr0: port 9(ath2) entered disabled state pacd: checking backhaul_ap interface --> network:0 - iface:ath11 - disabled:0 - mode:ap - device:wifi1 - backhaul_ap:0 repacd:osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xd6d18000 checking backhaul_ap interface --> network:0 - iface:ath2 - diOrbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20404 Comm:ifconfig :: PPID:6706 Comm:S98repacd <=< sabled:0 - mode:ap - device:wifi2 - backhaul_ap:1 repacd: checkSTOPPED EVENT for vap 1 (dec32000) ing backhaul_ap interface --> network:0 - iface:ath21 - disablesend_vdev_down_cmd_non_tlv for vap 1 (dec32000) d:0 - mode:sta - device:wifi2 - backhaul_ap:0 br0: port 4(ath01) entered disabled state Otherband BSSID 8c:3b:ad:24:db:8c Otherband BSSID 96:3b:ad:24:db:89 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20433 Comm:ifconfig :: PPID:6706 Comm:S98repacd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (d8eee000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 9(ath2) entered forwarding state br0: port 9(ath2) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath2 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd6d18000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20434 Comm:ifconfig :: PPID:6706 Comm:S98repacd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 1 (dec32000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/2 :: PPID:1 Comm:procd <=< su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 1 (dec32000) ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 br0: port 4(ath01) entered forwarding state br0: port 4(ath01) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath01 whc (repacd): Starting RE Placement and Auto-config Daemon send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd The sshenable is running ... not restart eth_handle when /tmp/disable_satelite_dhcpd existed send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Cannot connect to server , will try 60s later!!Sending SCAN START cmd Sending discover... Sending discover... Sending discover... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) not restart eth_handle when /tmp/disable_satelite_dhcpd existed Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending discover... Sending discover... Sending discover... Sending SCAN START cmd not restart eth_handle when /tmp/disable_satelite_dhcpd existed send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd Sending discover... Sending discover... Sending discover... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) not restart eth_handle when /tmp/disable_satelite_dhcpd existed Sending SCAN START cmd cac_timeout cac expired, chan 5540 curr time 4294889 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 3 send_vdev_up_cmd_non_tlv for vap 0 (d8eee000) __ieee80211_smart_ant_init: Smart Antenna is not supported Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd Sending discover... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) Sending discover... Current RAE Download File Path is /sw-apps/router-analytics/ and Router Model: rbs50 Sending discover... Download file https://http.fw.updates1.netgear.com/sw-apps/router-analytics/rbs50/fileinfo.txt failed! Sending SCAN START cmd not restart eth_handle when /tmp/disable_satelite_dhcpd existed send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) Sending discover... Sending SCAN START cmd Sending discover... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd Sending discover... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) not restart eth_handle when /tmp/disable_satelite_dhcpd existed [wlan]===time:Thu Oct 16 23:54:18 UTC 2025 command:wlan kickallclient============== send_vdev_down_cmd_non_tlv for vap 3 (dec32000) [wlan]===time:Thu Oct 16 23:54:20 UTC 2025 command:wlan connection deny============== Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:1595 Comm:ifconfig :: PPID:1594 Comm:wlan <=< STOPPED EVENT for vap 0 (dec32000) send_vdev_down_cmd_non_tlv for vap 0 (dec32000) br0: port 3(ath0) entered disabled state Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:1598 Comm:ifconfig :: PPID:1597 Comm:wlan <=< STOPPED EVENT for vap 0 (d942e000) send_vdev_down_cmd_non_tlv for vap 0 (d942e000) br0: port 7(ath1) entered disabled state Sending SCAN START cmd Sending SCAN START cmd Sending discover... send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) Sending discover... Sending discover... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd not restart eth_handle when /tmp/disable_satelite_dhcpd existed Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending discover... Sending discover... Sending SCAN START cmd Sending discover... send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) not restart eth_handle when /tmp/disable_satelite_dhcpd existed Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Download file https://http.fw.updates1.netgear.com/sw-apps/router-analytics/rbs50/fileinfo.txt failed! Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) Download file https://http.fw.updates1.netgear.com/sw-apps/router-analytics/rbs50/RAE_Policy.json failed! Sending discover... Sending discover... Sending SCAN START cmd Sending discover... send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd not restart eth_handle when /tmp/disable_satelite_dhcpd existed send_vdev_down_cmd_non_tlv for vap 1 (d8eee000) send_vdev_down_cmd_non_tlv for vap 3 (dec32000) Sending SCAN START cmd Sending discover... Sending SCAN START cmd Sending discover...

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 S - IMAGE_VARIANT_STRING=DAAAANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000023 S - Reset status Config, 0x00000000 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1339 - bootable_media_detect_entry, Start B - 118619 - bootable_media_detect_success, Start B - 118633 - elf_loader_entry, Start B - 121008 - auth_hash_seg_entry, Start B - 123151 - auth_hash_seg_exit, Start B - 160050 - elf_segs_hash_verify_entry, Start B - 274253 - PBL, End B - 274277 - SBL1, Start B - 366289 - pm_device_init, Start D - 9 - pm_device_init, Delta B - 367791 - boot_flash_init, Start D - 27900 - boot_flash_init, Delta B - 400039 - boot_config_data_table_init, Start D - 2995 - boot_config_data_table_init, Delta - (419 Bytes) B - 407720 - clock_init, Start D - 7533 - clock_init, Delta B - 419122 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 B - 422527 - sbl1_ddr_set_params, Start B - 427620 - cpr_init, Start D - 2 - cpr_init, Delta B - 432003 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13170 - sbl1_ddr_set_params, Delta B - 445298 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 516523 - sbl1_wait_for_ddr_training, Start D - 27 - sbl1_wait_for_ddr_training, Delta B - 532917 - Image Load, Start D - 14829 - QSEE Image Loaded, Delta - (262104 Bytes) B - 548174 - Image Load, Start D - 899 - SEC Image Loaded, Delta - (0 Bytes) B - 558023 - Image Load, Start D - 12424 - APPSBL Image Loaded, Delta - (416039 Bytes) B - 570873 - QSEE Execution, Start D - 60 - QSEE Execution, Delta B - 577067 - SBL1, End D - 304902 - SBL1, Delta S - Flash Throughput, 25922 KB/s (678738 Bytes, 26183 us) S - DDR Frequency, 672 MHz U-Boot 2012.07 [Barrier Breaker unknown,unknown] (Jan 04 2017 - 13:54:09) U-boot dni1 V1.4 for DNI HW ID: 29765352; NOR flash 32MB; EMMC flash 4000MB; RAM 512MB smem ram ptable found: ver: 1 len: 3 DRAM: 512 MiB machid : 0x8010001 NAND: ID = 0 Vendor = 0 Device = 0 Nand Flash error. Status = 64 ONFI Read id cmd failed ONFI probe failed SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 0 MiB MMC: qca_mmc: 0 *** Warning - bad CRC, using default environment PCI0 Link Intialized In: serial Out: serial Err: serial Valid chip addresses: 27 48 machid: 8010001 flash_type: 1 Net: MAC0 addr:8c:3b:ad:24:db:89 PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Hit any key to stop autoboot: 2 1 0 eth0 PHY0 Down Speed :10 Half duplex eth0 PHY1 Down Speed :10 Half duplex eth0 PHY2 Down Speed :10 Half duplex eth0 PHY3 Down Speed :10 Half duplex eth0 PHY4 Down Speed :10 Half duplex nmrp server is stopped or failed ! Read BootPart from BOARD DATA... mmc_read will run command: mmc read 0x871cfca8 0x2a22 0x100 MMC read: dev # 0, block # 10786, count 256 ... 256 blocks read: OK boot partition : 1 BootPart = 1 Loading DNI firmware for checking... MMC read: dev # 0, block # 17954, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18210, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 17954, count 1 ... 1 blocks read: OK ** rootfs address : 0x8433ffc0 ** ## Checking Image at 84000000 ... FIT image found FIT description: ARM OpenWrt FIT (Flattened Image Tree) Image 0 (kernel-1) Description: ARM OpenWrt Linux-6.6.119 Type: Kernel Image Compression: uncompressed Data Start: 0x840000e4 Data Size: 3316856 Bytes = 3.2 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: c3fd818b Hash algo: sha1 Hash value: f72bc69e95d0d4d3b6458a7d841a18a58f9235f1 Image 1 (fdt-1) Description: ARM OpenWrt netgear_rbr50 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84329e94 Data Size: 18468 Bytes = 18 KiB Architecture: ARM Hash algo: crc32 Hash value: 927eb7f5 Hash algo: sha1 Hash value: dcef9dea8c728445eda4fc04697bdd1987d29b83 Default Configuration: 'config@1' Configuration 0 (config@1) Description: OpenWrt netgear_rbr50 Kernel: kernel-1 FDT: fdt-1 ## Checking hash(es) for FIT Image at 84000000 ... Hash(es) for Image 0 (kernel-1): crc32+ sha1+ Hash(es) for Image 1 (fdt-1): crc32+ sha1+ ## Checking Image at 8433ffc0 ... Legacy image found Image Name: OpenWrt fake filesystem Image Type: ARM Linux Filesystem Image (uncompressed) Data Size: 0 Bytes = 0 Bytes Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK mmc_read will run command: mmc read 0x871cfca8 0x2a22 0x100 MMC read: dev # 0, block # 10786, count 256 ... 256 blocks read: OK boot partition : 1 MMC read: dev # 0, block # 17954, count 7680 ... 7680 blocks read: OK ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-6.6.119 Type: Kernel Image Compression: uncompressed Data Start: 0x840000e4 Data Size: 3316856 Bytes = 3.2 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: c3fd818b Hash algo: sha1 Hash value: f72bc69e95d0d4d3b6458a7d841a18a58f9235f1 Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt-1' FDT blob subimage Description: ARM OpenWrt netgear_rbr50 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84329e94 Data Size: 18468 Bytes = 18 KiB Architecture: ARM Hash algo: crc32 Hash value: 927eb7f5 Hash algo: sha1 Hash value: dcef9dea8c728445eda4fc04697bdd1987d29b83 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x84329e94 Loading Kernel Image ... OK OK Loading Device Tree to 871e8000, end 871ef823 ... OK Using machid 0x8010001 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.6.119 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 13.3.0 r29087-d9c5716d1d) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Wed Dec 17 21:08:22 2025 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: NETGEAR RBR50 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OF: reserved mem: 0x87e00000..0x87e7ffff (512 KiB) nomap non-reusable smem@87e00000 [ 0.000000] OF: reserved mem: 0x87e80000..0x87ffffff (1536 KiB) nomap non-reusable tz@87e80000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x0000000087dfffff] [ 0.000000] node 0: [mem 0x0000000087e00000-0x0000000087ffffff] [ 0.000000] node 0: [mem 0x0000000088000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 13 pages/cpu s21268 r8192 d23788 u53248 [ 0.000000] Kernel command line: root=/dev/mmcblk0p20 blkdevparts=mmcblk0:512K@17K(0:SBL1)ro,512K(0:BOOTCONFIG)ro,512K(0:QSEE)ro,512K(0:QSEE_ALT)ro,256K(0:CDT)ro,256K(0:CDT_ALT)ro,256K(0:DDRPARAMS)ro,256K(0:APPSBLENV)ro,1M(0:APPSBL)ro,1M(0:APPSBL_ALT)ro,256K(0:ART)ro,256K(ARTMTD)ro,2M(language)ro,256K(config)ro,256K(pot)ro,256K(traffic_meter)ro,256K(pot_bak)ro,256K(traffic_meter.bak)ro,3840K(kernel),31488K(rootfs),35328K@9233K(firmware),256K(mtdoops)ro,1457651200(reserved)ro,-(unallocated) rootfstype=squashfs,ext4 rootwait [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 505776K/524288K available (7681K kernel code, 644K rwdata, 1136K rodata, 1024K init, 251K bss, 18512K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000004] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000020] Switching to timer-based delay loop, resolution 20ns [ 0.000321] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000343] CPU: Testing write buffer coherency: ok [ 0.000397] pid_max: default: 32768 minimum: 301 [ 0.010126] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.010150] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.018567] qcom_scm: convention: smc legacy [ 0.020064] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.020243] Setting up static identity map for 0x80300000 - 0x8030003c [ 0.020450] rcu: Hierarchical SRCU implementation. [ 0.020458] rcu: Max phase no-delay instances is 1000. [ 0.021144] smp: Bringing up secondary CPUs ... [ 0.024857] smp: Brought up 1 node, 4 CPUs [ 0.024880] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.024893] CPU: All CPU(s) started in SVC mode. [ 0.033019] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.033267] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.033294] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.038372] pinctrl core: initialized pinctrl subsystem [ 0.041720] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.042156] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.043557] thermal_sys: Registered thermal governor 'step_wise' [ 0.043681] cpuidle: using governor ladder [ 0.043723] cpuidle: using governor menu [ 0.061895] cryptd: max_cpu_qlen set to 1000 [ 0.066713] usbcore: registered new interface driver usbfs [ 0.066783] usbcore: registered new interface driver hub [ 0.066841] usbcore: registered new device driver usb [ 0.066895] pps_core: LinuxPPS API ver. 1 registered [ 0.066904] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.066928] PTP clock support registered [ 0.069639] clocksource: Switched to clocksource arch_sys_counter [ 0.080280] NET: Registered PF_INET protocol family [ 0.080525] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.082856] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.082897] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.082918] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.082980] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.083132] TCP: Hash tables configured (established 4096 bind 4096) [ 0.084173] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.084561] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.084604] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.085340] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.085395] PCI: CLS 0 bytes, default 64 [ 0.087168] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.088207] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.088223] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.431288] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.436938] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.437080] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.437179] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.437273] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.437705] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.440602] qcom-pcie 40000000.pci: host bridge /soc/pci@40000000 ranges: [ 0.440676] qcom-pcie 40000000.pci: IO 0x0040200000..0x00402fffff -> 0x0000000000 [ 0.440708] qcom-pcie 40000000.pci: MEM 0x0040300000..0x0040ffffff -> 0x0040300000 [ 0.442257] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.442339] msm_serial 78af000.serial: uartclk = 1843200 [ 0.442751] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 31, base_baud = 115200) is a MSM [ 0.442792] msm_serial: console setup on port #0 [ 0.442847] printk: console [ttyMSM0] enabled [ 0.581466] qcom-pcie 40000000.pci: iATU: unroll F, 32 ob, 8 ib, align 4K, limit 4G [ 0.587102] msm_serial: driver initialized [ 0.608911] qcom-pcie 40000000.pci: Invalid eDMA IRQs found [ 0.624306] loop: module loaded [ 0.729636] qcom-pcie 40000000.pci: PCIe Gen.2 x1 link up [ 0.781804] i2c_dev: i2c /dev entries driver [ 0.782941] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00 [ 0.787409] i2c_qup 78b7000.i2c: using default clock-frequency 100000 [ 0.791361] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.791379] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] [ 0.791394] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] [ 0.800780] sdhci: Secure Digital Host Controller Interface driver [ 0.802425] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400 [ 0.809772] sdhci: Copyright(c) Pierre Ossman [ 0.819829] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff] [ 0.826485] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.831679] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.838852] sdhci_msm 7824900.mmc: Got CD GPIO [ 0.846196] PCI: bus0: Fast back to back transfers disabled [ 1.194441] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000 [ 1.199717] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 1.206392] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.213257] PCI: bus1: Fast back to back transfers disabled [ 1.218623] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] [ 1.223996] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff] [ 1.230940] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] [ 1.237746] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.244817] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] [ 1.254273] pcieport 0000:00:00.0: AER: enabled with IRQ 61 [ 1.262502] NET: Registered PF_INET6 protocol family [ 1.265214] Segment Routing with IPv6 [ 1.267621] In-situ OAM (IOAM) with IPv6 [ 1.271312] NET: Registered PF_PACKET protocol family [ 1.275145] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.280437] 8021q: 802.1Q VLAN Support v1.8 [ 1.292693] mmc0: SDHCI controller on 7824900.mmc [7824900.mmc] using ADMA 64-bit [ 1.293362] Registering SWP/SWPB emulation handler [ 1.332451] qca8k-ipq4019 c000000.switch: configuring for fixed/internal link mode [ 1.332842] qca8k-ipq4019 c000000.switch: Link is Up - 1Gbps/Full - flow control rx/tx [ 1.363320] mmc0: new HS200 MMC card at address 0001 [ 1.364444] mmcblk0: mmc0:0001 4FPD3R 3.64 GiB [ 1.368196] Overlapping partitions are used in command line partitions. [ 1.368212] Don't use filesystems on overlapping partitions: [ 1.371708] kernel[9192448,3932160] overlaps with firmware[9454592,36175872]. [ 1.378129] rootfs[13124608,32243712] overlaps with firmware[9454592,36175872]. [ 1.384094] mmcblk0: p1(0:SBL1) p2(0:BOOTCONFIG) p3(0:QSEE) p4(0:QSEE_ALT) p5(0:CDT) p6(0:CDT_ALT) p7(0:DDRPARAMS) p8(0:APPSBLENV) p9(0:APPSBL) p10(0:APPSBL_ALT) p11(0:ART) p12(ARTMTD) p13(language) p14(config) p15(pot) p16(traffic_meter) p17(pot_bak) p18(traffic_meter.bak) p19(kernel) p20(rootfs) p21(firmware) p22(mtdoops) p23(reserved) p24(unallocated) [ 1.410639] mmcblk0boot0: mmc0:0001 4FPD3R 4.00 MiB [ 1.430960] mmcblk0boot1: mmc0:0001 4FPD3R 4.00 MiB [ 1.435088] mmcblk0rpmb: mmc0:0001 4FPD3R 512 KiB, chardev (246:0) [ 1.531550] qca8k-ipq4019 c000000.switch wan (uninitialized): PHY [90000.mdio-1:00] driver [Qualcomm QCA8075] (irq=POLL) [ 1.610451] qca8k-ipq4019 c000000.switch lan1 (uninitialized): PHY [90000.mdio-1:01] driver [Qualcomm QCA8075] (irq=POLL) [ 1.690509] qca8k-ipq4019 c000000.switch lan2 (uninitialized): PHY [90000.mdio-1:02] driver [Qualcomm QCA8075] (irq=POLL) [ 1.770532] qca8k-ipq4019 c000000.switch lan3 (uninitialized): PHY [90000.mdio-1:03] driver [Qualcomm QCA8075] (irq=POLL) [ 1.771792] ipqess-edma c080000.ethernet eth0: entered promiscuous mode [ 1.780643] DSA: tree 0 setup [[ 1.795614] VFS: Mounted root (squashfs filesystem) readonly on device 259:12. [ 1.797715] Freeing unused kernel image (initmem) memory: 1024K [ 1.802069] Run /sbin/init as init process [ 2.134346] init: Console is alive [ 2.134732] init: - watchdog - [ 2.898242] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.956140] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 3.060536] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.060623] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.065206] xhci-hcd xhci-hcd.0.auto: USB3 root hub has no ports [ 3.072549] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000008002000010 [ 3.078810] xhci-hcd xhci-hcd.0.auto: irq 65, io mem 0x06000000 [ 3.088966] hub 1-0:1.0: USB hub found [ 3.093859] hub 1-0:1.0: 1 port detected [ 3.105924] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.107831] init: - preinit - [ 7.189663] random: crng init done Cannot parse config file '/etc/fw_env.config': No such file or directory Failed to find NVMEM device [ 7.846316] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode [ 7.847085] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode [ 7.853235] qca8k-ipq4019 c000000.switch: PSGMII calibration! [ 7.860941] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.201112] loop0: detected capacity change from 0 to 62976 [ 13.239696] loop0: detected capacity change from 62976 to 52352 [ 13.277053] EXT4-fs (loop0): recovery complete [ 13.278416] EXT4-fs (loop0): mounted filesystem eb39f4eb-5875-4ef7-be7f-9eb565872961 r/w with ordered data mode. Quota mode: disabled. [ 13.281598] mount_root: switching to ext4 overlay [ 13.293539] platform 8a00000.usb: deferred probe pending [ 13.300043] urandom-seed: Seeding with /etc/urandom.seed [ 13.422755] procd: - early - [ 13.422987] procd: - watchdog - [ 14.024342] procd: - watchdog - [ 14.036183] procd: - ubus - [ 14.197383] procd: - init - Please press Enter to activate this console. [ 14.746176] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.782828] Loading modules backported from Linux version v6.12.61-0-gdcbeffaf66d0 [ 14.782885] Backport generated by backports.git v6.1.110-1-35-g410656ef [ 14.963467] PPP generic driver version 2.4.2 [ 14.965852] NET: Registered PF_PPPOX protocol family [ 15.006429] ath10k 6.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 15.007461] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 15.013986] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 15.612247] urngd: v1.0.2 started. [ 15.972279] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 15.972355] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 15.985428] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 [ 18.325054] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:6 crc32 0bfe5c35 [ 21.847578] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 21.847649] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 21.930959] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 21.931778] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 22.221144] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 23.219385] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 23.219458] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 23.231417] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 23.373821] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 2d972a4b [ 24.661221] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 24.661302] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 24.708638] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 24.709595] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 24.855074] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 25.611178] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 25.611272] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 25.623203] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 25.687326] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 2d972a4b [ 26.976218] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 26.976289] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 27.023364] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 27.024328] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 27.160550] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 27.281084] kmodloader: done loading kernel modules from /etc/modules.d/* [ 33.929529] ipqess-edma c080000.ethernet eth0: Link is Down [ 33.936813] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode [ 33.937155] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 33.946851] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode [ 33.954160] br-lan: port 1(lan1) entered blocking state [ 33.959737] br-lan: port 1(lan1) entered disabled state [ 33.964890] qca8k-ipq4019 c000000.switch lan1: entered allmulticast mode [ 33.970214] ipqess-edma c080000.ethernet eth0: entered allmulticast mode [ 33.977518] qca8k-ipq4019 c000000.switch lan1: entered promiscuous mode [ 34.004694] qca8k-ipq4019 c000000.switch lan2: configuring for phy/psgmii link mode [ 34.006470] br-lan: port 2(lan2) entered blocking state [ 34.011292] br-lan: port 2(lan2) entered disabled state [ 34.016480] qca8k-ipq4019 c000000.switch lan2: entered allmulticast mode [ 34.022196] qca8k-ipq4019 c000000.switch lan2: entered promiscuous mode [ 34.036957] qca8k-ipq4019 c000000.switch lan3: configuring for phy/psgmii link mode [ 34.038523] br-lan: port 3(lan3) entered blocking state [ 34.043637] br-lan: port 3(lan3) entered disabled state [ 34.048743] qca8k-ipq4019 c000000.switch lan3: entered allmulticast mode [ 34.054690] qca8k-ipq4019 c000000.switch lan3: entered promiscuous mode [ 34.078257] qca8k-ipq4019 c000000.switch wan: configuring for phy/psgmii link mode

You can check and edit the boot partition in the Uboot shell using the UART connection
- boot_partition_show shows the current boot partition
- boot_partition_set 1 sets the current boot partition to 1
Router MAC addresses:
- LAN XX:XX:XX:XX:XX:69
- WAN XX:XX:XX:XX:XX:6a
- WIFI 2G XX:XX:XX:XX:XX:6a
- WIFI 5G XX:XX:XX:XX:XX:6b
- WIFI 5G (2nd) XX:XX:XX:XX:XX:6c
- LABEL XX:XX:XX:XX:XX:69

How to add tags

ipq40xx, IPQ4019, 4096emmc, 512ram, 4port, GigabitEthernet, 1usb, usb2.0, rbk50, orbi

ipq40xx ipq4019 4096emmc 512ram 4port gigabitethernet 1usb usb2.0 rbk50 orbi

NETGEAR RBS50

Supported Versions

v1

v2

Experimental Versions

Hardware Highlights

Installation

v1

NMRPflash Method

Vendor-UI Method

Revert to stock firmware

v2

Flash Layout

Upgrading OpenWrt

Debricking

v1

v2

Failsafe mode

Basic configuration

Specific Configuration

Network interfaces

Switch Ports (for VLANs)

Buttons

Hardware

Info

Photos

Opening the case

Serial

JTAG

Bootloader mods

Hardware mods

Bootlogs

OEM bootlog

OpenWrt bootlog

Notes

Tags