Netgear RBR40

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The RBR40 is the router part of the RBK40 kit, which consists of a router and one or more satellites, all of them being AC-2200 devices.

None at this time.

→ Install OpenWrt (generic explanation)

Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

How you install OpenWrt from a device freshly opened
The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

Browse to http://192.168.1.1/Upgrade.asp
Upload .bin file to router
Wait for it to reboot
Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

→ generic.flashing.tftp

Specific values needed for tftp

Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address	FILL-IN
Bootloader MAC address (special)	FILL-IN
Firmware tftp image	Latest OpenWrt release (`NOTE:` Name must contain “tftp”)
TFTP transfer window	FILL-IN seconds
TFTP window start	approximately FILL-IN seconds after power on
TFTP client required IP address	FILL-IN

→ generic.sysupgrade

These are generic instructions. Update with your router's specifics.

Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
Upload image file for sysupgrade to LuCI
Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

sysupgrade
mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

Login as root via SSH on 192.168.1.1, then enter the following commands:

cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

Login as root via SSH on 192.168.1.1, then enter the following commands:

cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

→ generic.debrick

→ failsafe_and_factory_reset

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	EXAMPLE LAN & WiFi	EXAMPLE 192.168.1.1/24
vlan0 (eth0.0)	EXAMPLE LAN ports (1 to 4)	EXAMPLE None
vlan1 (eth0.1)	EXAMPLE WAN port	EXAMPLE DHCP
wl0	EXAMPLE WiFi	EXAMPLE Disabled

Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port	Switch port
Internet (WAN)	EXAMPLE 4
LAN 1	EXAMPLE 3
LAN 2	EXAMPLE 2
LAN 3	EXAMPLE 1
LAN 4	EXAMPLE 0

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

Please fill in real values for this device, then remove the EXAMPLEs

The Netgear RBR40 has the following buttons:

BUTTON	Event
EXAMPLE Reset	reset
EXAMPLE Secure Easy Setup	ses
EXAMPLE No buttons at all.	-

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

→ Warranty

Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

Replace EXAMPLE by real values.

Serial connection parameters for Netgear RBR40 @@Version@@	EXAMPLE 115200, 8N1, 3.3V

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

→ bootloader

None so far.

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 S - IMAGE_VARIANT_STRING=DAAAANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000023 S - Reset status Config, 0x00000000 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1339 - bootable_media_detect_entry, Start B - 34603 - bootable_media_detect_success, Start B - 34617 - elf_loader_entry, Start B - 36811 - auth_hash_seg_entry, Start B - 38957 - auth_hash_seg_exit, Start B - 73715 - elf_segs_hash_verify_entry, Start B - 187903 - PBL, End B - 187928 - SBL1, Start B - 279980 - pm_device_init, Start D - 9 - pm_device_init, Delta B - 281489 - boot_flash_init, Start D - 37824 - boot_flash_init, Delta B - 323660 - boot_config_data_table_init, Start D - 2819 - boot_config_data_table_init, Delta - (419 Bytes) B - 331379 - clock_init, Start D - 7530 - clock_init, Delta B - 342672 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 B - 346077 - sbl1_ddr_set_params, Start B - 351170 - cpr_init, Start D - 2 - cpr_init, Delta B - 355552 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13170 - sbl1_ddr_set_params, Delta B - 368848 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 439997 - sbl1_wait_for_ddr_training, Start D - 28 - sbl1_wait_for_ddr_training, Delta B - 456235 - Image Load, Start D - 15036 - QSEE Image Loaded, Delta - (262104 Bytes) B - 471701 - Image Load, Start D - 899 - SEC Image Loaded, Delta - (0 Bytes) B - 481549 - Image Load, Start D - 12513 - APPSBL Image Loaded, Delta - (415855 Bytes) B - 494488 - QSEE Execution, Start D - 60 - QSEE Execution, Delta B - 500663 - SBL1, End D - 314847 - SBL1, Delta S - Flash Throughput, 25166 KB/s (678554 Bytes, 26963 us) S - DDR Frequency, 672 MHz U-Boot 2012.07 [Barrier Breaker unknown,unknown] (Dec 01 2016 - 16:53:29) U-boot dni1 V0.3 for DNI HW ID: 29765515; NOR flash 0MB; EMMC flash 4096MB; RAM 512MB smem ram ptable found: ver: 1 len: 3 DRAM: 512 MiB machid : 0x8010001 NAND: ID = 0 Vendor = 0 Device = 0 Nand Flash error. Status = 64 ONFI Read id cmd failed ONFI probe failed SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 0 MiB MMC: qca_mmc: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Valid chip addresses: 27 48 machid: 8010001 flash_type: 1 Net: MAC0 addr:a0:40:a0:70:09:e6 PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Hit any key to stop autoboot: 2 1 0 eth0 PHY0 Down Speed :10 Half duplex eth0 PHY1 Down Speed :10 Half duplex eth0 PHY2 Down Speed :10 Half duplex eth0 PHY3 Down Speed :10 Half duplex eth0 PHY4 Down Speed :10 Half duplex nmrp server is stopped or failed ! Read BootPart from BOARD DATA... mmc_read will run command: mmc read 0x871cfba8 0x2a22 0x100 MMC read: dev # 0, block # 10786, count 256 ... 256 blocks read: OK boot partition : 1 BootPart = 1 Loading DNI firmware for checking... MMC read: dev # 0, block # 17954, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18210, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24610, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24866, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25122, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25378, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25634, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 25890, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26146, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26402, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26658, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 26914, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27170, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27426, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27682, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 27938, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28194, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28450, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28706, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 28962, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29218, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29474, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29730, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 29986, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30242, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30498, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 30754, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31010, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31266, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31522, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 31778, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32034, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32290, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32546, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 32802, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33058, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33314, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33570, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 33826, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34082, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34338, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34594, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 34850, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35106, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35362, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35618, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 35874, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36130, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36386, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36642, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 36898, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37154, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37410, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37666, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 37922, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38178, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38434, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38690, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 38946, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39202, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39458, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39714, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 39970, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40226, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40482, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40738, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 40994, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41250, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41506, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 41762, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42018, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42274, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42530, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 42786, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43042, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43298, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43554, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 43810, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44066, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44322, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44578, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 44834, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45090, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45346, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45602, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 45858, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46114, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46370, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46626, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 46882, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47138, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47394, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47650, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 47906, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48162, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48418, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48674, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 48930, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49186, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49442, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49698, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 49954, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50210, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 50978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 51746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 52770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 53794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 54818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 55842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56610, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 56866, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57122, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57378, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57634, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 57890, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58146, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58402, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58658, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 58914, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59170, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59426, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59682, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 59938, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60194, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60450, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60706, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 60962, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61218, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61474, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61730, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 61986, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62242, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62498, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 62754, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63010, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63266, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63522, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 63778, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64034, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64290, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64546, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 64802, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65058, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65314, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65570, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 65826, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66082, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66338, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66594, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 66850, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67106, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67362, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67618, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 67874, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68130, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68386, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68642, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 68898, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69154, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69410, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69666, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 69922, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70178, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70434, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70690, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 70946, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71202, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71458, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71714, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 71970, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 72226, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 72482, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 72738, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 72994, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 73250, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 73506, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 73762, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 74018, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 74274, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 74530, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 74786, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 75042, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 75298, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 75554, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 75810, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 76066, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 76322, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 76578, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 76834, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 77090, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 77346, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 77602, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 77858, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 78114, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 78370, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 78626, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 78882, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 79138, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 79394, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 79650, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 79906, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 80162, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 80418, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 80674, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 80930, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 81186, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 81442, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 81698, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 81954, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 82210, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 82466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 82722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 82978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 83234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 83490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 83746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 84002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 84258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 84514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 84770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 85026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 85282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 85538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 17954, count 1 ... 1 blocks read: OK ** rootfs address : 0x8433ffc0 ** ## Checking Image at 84000000 ... FIT image found FIT description: ARM OpenWrt FIT (Flattened Image Tree) Image 0 (kernel@1) Description: ARM OpenWrt Linux-3.14.77 Type: Kernel Image Compression: gzip compressed Data Start: 0x840000e4 Data Size: 3025384 Bytes = 2.9 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 76e4b2db Hash algo: sha1 Hash value: 1a76f28de73ab3c9ce5d03d7136aabfea69f60c5 Image 1 (fdt@1) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842e2c0c Data Size: 38605 Bytes = 37.7 KiB Architecture: ARM Hash algo: crc32 Hash value: b0c59ce9 Hash algo: sha1 Hash value: d26c1dfede344382e260a8ca7cfcd3306a59482a Image 2 (fdt@2) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842ec3e8 Data Size: 43035 Bytes = 42 KiB Architecture: ARM Hash algo: crc32 Hash value: 3ec0046d Hash algo: sha1 Hash value: f68529aa5c64ac8fb3df893db744ab87366cdd3e Image 3 (fdt@3) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842f6d10 Data Size: 42101 Bytes = 41.1 KiB Architecture: ARM Hash algo: crc32 Hash value: 0109faf0 Hash algo: sha1 Hash value: 34ee6bdafd6315d361d6aa99b5ad45a9944b32dd Image 4 (fdt@4) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84301294 Data Size: 34248 Bytes = 33.4 KiB Architecture: ARM Hash algo: crc32 Hash value: 0fa6ee98 Hash algo: sha1 Hash value: dcec33a744cfed6a21c9a9be313791f98b1081ff Image 5 (fdt@5) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x84309968 Data Size: 34407 Bytes = 33.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 96f6beb1 Hash algo: sha1 Hash value: 3a938e8901b816f4fa7d73aacbc3e2b54422c5d0 Image 6 (fdt@6) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843120dc Data Size: 34547 Bytes = 33.7 KiB Architecture: ARM Hash algo: crc32 Hash value: ce835bd9 Hash algo: sha1 Hash value: f48535f83fe16c4d3471b18ddab6dfa5d1a633e7 Image 7 (fdt@7) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8431a8dc Data Size: 38588 Bytes = 37.7 KiB Architecture: ARM Hash algo: crc32 Hash value: bb010bc8 Hash algo: sha1 Hash value: a52a0530438afae1fe5fed13cb380503d0ee576b Image 8 (fdt@8) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843240a4 Data Size: 38467 Bytes = 37.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 311234ec Hash algo: sha1 Hash value: c7be34f25ccb51f0d0eaa6985af77d30b872eaef Image 9 (fdt@9) Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x8432d7f4 Data Size: 38165 Bytes = 37.3 KiB Architecture: ARM Hash algo: crc32 Hash value: f91b53ee Hash algo: sha1 Hash value: 7f783a91e42dc651bb82f01479f5207640db0d53 Default Configuration: 'config@1' Configuration 0 (config@1) Description: OpenWrt Kernel: kernel@1 FDT: fdt@1 Configuration 1 (config@2) Description: OpenWrt Kernel: kernel@1 FDT: fdt@2 Configuration 2 (config@3) Description: OpenWrt Kernel: kernel@1 FDT: fdt@3 Configuration 3 (config@4) Description: OpenWrt Kernel: kernel@1 FDT: fdt@4 Configuration 4 (config@5) Description: OpenWrt Kernel: kernel@1 FDT: fdt@5 Configuration 5 (config@6) Description: OpenWrt Kernel: kernel@1 FDT: fdt@6 Configuration 6 (config@7) Description: OpenWrt Kernel: kernel@1 FDT: fdt@7 Configuration 7 (config@8) Description: OpenWrt Kernel: kernel@1 FDT: fdt@8 Configuration 8 (config@9) Description: OpenWrt Kernel: kernel@1 FDT: fdt@9 ## Checking hash(es) for FIT Image at 84000000 ... Hash(es) for Image 0 (kernel@1): crc32+ sha1+ Hash(es) for Image 1 (fdt@1): crc32+ sha1+ Hash(es) for Image 2 (fdt@2): crc32+ sha1+ Hash(es) for Image 3 (fdt@3): crc32+ sha1+ Hash(es) for Image 4 (fdt@4): crc32+ sha1+ Hash(es) for Image 5 (fdt@5): crc32+ sha1+ Hash(es) for Image 6 (fdt@6): crc32+ sha1+ Hash(es) for Image 7 (fdt@7): crc32+ sha1+ Hash(es) for Image 8 (fdt@8): crc32+ sha1+ Hash(es) for Image 9 (fdt@9): crc32+ sha1+ ## Checking Image at 8433ffc0 ... Legacy image found Image Name: ARM OpenWrt Linux-3.14.77 Image Type: ARM Linux Kernel Image (lzma compressed) Data Size: 31197184 Bytes = 29.8 MiB Load Address: 40908000 Entry Point: 40908000 Verifying Checksum ... OK mmc_read will run command: mmc read 0x871cfba8 0x2a22 0x100 MMC read: dev # 0, block # 10786, count 256 ... 256 blocks read: OK boot partition : 1 MMC read: dev # 0, block # 17954, count 7680 ... 7680 blocks read: OK ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM OpenWrt Linux-3.14.77 Type: Kernel Image Compression: gzip compressed Data Start: 0x840000e4 Data Size: 3025384 Bytes = 2.9 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 76e4b2db Hash algo: sha1 Hash value: 1a76f28de73ab3c9ce5d03d7136aabfea69f60c5 Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt@1' FDT blob subimage Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842e2c0c Data Size: 38605 Bytes = 37.7 KiB Architecture: ARM Hash algo: crc32 Hash value: b0c59ce9 Hash algo: sha1 Hash value: d26c1dfede344382e260a8ca7cfcd3306a59482a Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x842e2c0c Uncompressing Kernel Image ... OK Loading Device Tree to 871e3000, end 871ef6cc ... OK Using machid 0x8010001 from environment Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 3.14.77 (jackie@TWTPEB2S1UB16) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r6043) ) #1 SMP PREEMPT Tue Oct 28 13:35:33 CST 2025 CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK04.1-C1 Flash name: EMMC Memory policy: Data cache writealloc PERCPU: Embedded 8 pages/cpu @dfbc7000 s8448 r8192 d16128 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 128768 Kernel command line: rootwait clk_ignore_unused user_debug=0xff PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 508056K/519168K available (4219K kernel code, 240K rwdata, 1332K rodata, 172K init, 357K bss, 11112K reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0208000 - 0xc07741e0 (5553 kB) .init : 0xc0775000 - 0xc07a0100 ( 173 kB) .data : 0xc07a2000 - 0xc07de378 ( 241 kB) .bss : 0xc07de378 - 0xc0837b00 ( 358 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Preemptible hierarchical RCU implementation. NR_IRQS:16 nr_irqs:16 16 Architected cp15 timer(s) running at 48.00MHz (virt). sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns Switching to timer-based delay loop Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x80213278 - 0x802132d0 CPU1: Booted secondary processor i2c devices info CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU2: Booted secondary processor i2c devices info CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 CPU3: Booted secondary processor i2c devices info CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 Brought up 4 CPUs SMP: Total of 4 processors activated (384.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 2048 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 2 hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 3 hw-breakpoint: CPU 2 failed to disable vector catch hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 Version Rollback Feature Disabled i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2 i2c i2c-0: Failed to register i2c client tlc59208f at 0x27 (-16) i2c i2c-0: Can't create device at 0x27 i2c i2c-0: Failed to register i2c client tlc59208f at 0x27 (-16) i2c i2c-0: Can't create device at 0x27 sps:sps is ready. bio: create slab <bio-0> at 0 SD0 VccQ: 1800 <--> 3000 mV usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb msm_bus_fabric_init_driver msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1 msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1 Neighbour init complete, with restricted-GC and GC-lock enabled 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0. msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready! msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0. msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initialized PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x40200000-0x402fffff] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0014[4] is all FFs PCI: bus0: Fast back to back transfers disabled pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 1:0x00 + 0x0014[4] is all FFs PCI: bus1: Fast back to back transfers disabled msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0028[4] is all FFs pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] msm_pcie_probe: msm_pcie_probe: RC0 is enabled in bootup Switched to clocksource arch_sys_counter NET: Registered protocol family 2 create ipmac proc TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available futex hash table entries: 1024 (order: 4, 65536 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 992 NET: Registered protocol family 38 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler noop registered io scheduler deadline registered (default) tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 tcsr 1953000.ess_tcsr: setting ess interface select = 0 tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled msm_serial_hsl_probe: detected port #0 (ttyMSM0) msm_serial_hsl_probe: Bus scaling is disabled 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM msm_hsl_console_setup: console setup on port #0 console [ttyMSM0] enabled msm_serial_hsl_probe: detected port #1 (ttyMSM1) msm_serial_hsl_probe: Bus scaling is disabled 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 140, base_baud = 115200) is a MSM msm_serial_hsl_init: driver initialized qca_serial_hs module loaded sps: BAM device 0x07884000 is not registered yet. sps:BAM 0x07884000 is registered. sps:BAM 0x07884000 (va:0xe0b00000) enabled: ver:0x19, number of pipes:12 m25p80 spi0.0: Failed to find sector-size libphy: ipq40xx_mdio: probed ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered dwc3 8a00000.dwc3: no usb2 phy configured platform 8a00000.dwc3: Driver dwc3 requests probe deferral dwc3 6000000.dwc3: no usb2 phy configured platform 6000000.dwc3: Driver dwc3 requests probe deferral ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-platform: EHCI generic platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-platform: OHCI generic platform driver i2c /dev entries driver tlc59208f init! tlc59208f probe i2c-core: driver [tlc59208f] using legacy suspend method i2c-core: driver [tlc59208f] using legacy resume method debug defined config_mmc_test in mmc_register_driver debug defined config_mmc_test in mmc_register_driver sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper sdhci_msm 7824900.sdhci: Got SD LDO GPIO #33 sdhci_msm 7824900.sdhci: Got CD GPIO #22. mmc0: no vmmc regulator found mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (7938 buckets, 31752 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered l2tp_core: L2TP core driver, V2.0 l2tp_netlink: L2TP netlink interface 8021q: 802.1Q VLAN Support v1.8 Registering SWP/SWPB emulation handler regulator-dummy: disabling mmc0: BKOPS_EN bit is not set mmc0: new HS200 MMC card at address 0001 mmcblk mmc0:0001: Card claimed for testing. debug mmc_bus_probe mmcblk0: mmc0:0001 M62704 3.53 GiB mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB mmc0: Starting tests of card mmc0:0001... mmc0: Test case 4. ART read (with data verification and return)... mmc_art_verify_read: the board_data is 110401 mmc0: Result: OK mmc0: Tests completed. mmc_dni_art_read_boot_part: rootfs part is #01 read_boot_part_from_art: the rootfs part num is #01 ART part: device [179:20] mmcblk0p20 set to be root filesystem #: vol name is 0:SBL1, start is 0x22, size is 0x400, ssz is 0x1 #: vol name is 0:BOOTCONFIG, start is 0x422, size is 0x400, ssz is 0x1 #: vol name is 0:QSEE, start is 0x822, size is 0x400, ssz is 0x1 #: vol name is 0:QSEE_ALT, start is 0xc22, size is 0x400, ssz is 0x1 #: vol name is 0:CDT, start is 0x1022, size is 0x200, ssz is 0x1 #: vol name is 0:CDT_ALT, start is 0x1222, size is 0x200, ssz is 0x1 #: vol name is 0:DDRPARAMS, start is 0x1422, size is 0x200, ssz is 0x1 #: vol name is 0:APPSBLENV, start is 0x1622, size is 0x200, ssz is 0x1 #: vol name is 0:APPSBL, start is 0x1822, size is 0x800, ssz is 0x1 #: vol name is 0:APPSBL_ALT, start is 0x2022, size is 0x800, ssz is 0x1 #: vol name is 0:ART, start is 0x2822, size is 0x200, ssz is 0x1 #: vol name is ARTMTD, start is 0x2a22, size is 0x200, ssz is 0x1 #: vol name is language, start is 0x2c22, size is 0x1000, ssz is 0x1 #: vol name is config, start is 0x3c22, size is 0x200, ssz is 0x1 #: vol name is pot, start is 0x3e22, size is 0x200, ssz is 0x1 #: vol name is traffic_meter, start is 0x4022, size is 0x200, ssz is 0x1 #: vol name is pot_bak, start is 0x4222, size is 0x200, ssz is 0x1 #: vol name is traffic_meter.bak, start is 0x4422, size is 0x200, ssz is 0x1 #: vol name is kernel, start is 0x4622, size is 0x1a00, ssz is 0x1 #: vol name is rootfs, start is 0x6022, size is 0xfa00, ssz is 0x1 #: vol name is firmware, start is 0x4622, size is 0x11400, ssz is 0x1 #: vol name is mtdoops, start is 0x15a22, size is 0x200, ssz is 0x1 #: vol name is cert, start is 0x15c22, size is 0x80, ssz is 0x1 #: vol name is kernel-2, start is 0x15ca2, size is 0x1a00, ssz is 0x1 #: vol name is rootfs-2, start is 0x176a2, size is 0xfa00, ssz is 0x1 #: vol name is firmware-2, start is 0x15ca2, size is 0x11400, ssz is 0x1 #: vol name is device_table, start is 0x270a2, size is 0x2800, ssz is 0x1 #: vol name is circle, start is 0x298a2, size is 0x18000, ssz is 0x1 #: vol name is streamboost, start is 0x418a2, size is 0x19000, ssz is 0x1 #: vol name is forceshield, start is 0x5a8a2, size is 0xf000, ssz is 0x1 #: vol name is arlo, start is 0x698a2, size is 0x2800, ssz is 0x1 #: vol name is rae, start is 0x6c0a2, size is 0x1000, ssz is 0x1 #: vol name is armor, start is 0x6d0a2, size is 0x19000, ssz is 0x1 #: vol name is ntgrcrydata, start is 0x860a2, size is 0x5000, ssz is 0x1 #: vol name is jdx, start is 0x8b0a2, size is 0x200, ssz is 0x1 #: vol name is reserved, start is 0x8b2a2, size is 0x249aff, ssz is 0x1 mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 p34 p35 p36 mmcblk0boot1: unknown partition table mmcblk0boot0: unknown partition table xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: xHCI Host Controller usb usb1: Manufacturer: Linux 3.14.77 xhci-hcd usb usb1: SerialNumber: xhci-hcd.0.auto hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.14.77 xhci-hcd usb usb2: SerialNumber: xhci-hcd.0.auto hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000 usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.14.77 xhci-hcd usb usb3: SerialNumber: xhci-hcd.1.auto hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.14.77 xhci-hcd usb usb4: SerialNumber: xhci-hcd.1.auto hub 4-0:1.0: USB hub found hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) drivers/rtc/hctosys.c: unable to open rtc device (rtc0) clk: Not disabling unused clocks VFS: Mounted root (squashfs filesystem) readonly on device 179:20. Freeing unused kernel memory: 172K (c0775000 - c07a0000) init: Console is alive init: - watchdog - random: kmodloader: uninitialized urandom read (4 bytes read, 39 bits of entropy available) init: - preinit - random: sh: uninitialized urandom read (4 bytes read, 57 bits of entropy available) random: procd: uninitialized urandom read (4 bytes read, 63 bits of entropy available) random: cat: uninitialized urandom read (4 bytes read, 68 bits of entropy available) random: mkdir: uninitialized urandom read (4 bytes read, 68 bits of entropy available) random: mkdir: uninitialized urandom read (4 bytes read, 68 bits of entropy available) random: grep: uninitialized urandom read (4 bytes read, 68 bits of entropy available) random: mktemp: uninitialized urandom read (4 bytes read, 68 bits of entropy available) random: mktemp: uninitialized urandom read (6 bytes read, 68 bits of entropy available) random: mktemp: uninitialized urandom read (4 bytes read, 68 bits of entropy available) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level Before mount_root Before DNI mount_root After DNI mount_root After mount_root procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. Tue Oct 28 05:36:00 UTC 2025 datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 1/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 2/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 3/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 4/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 5/5) datalib - socket() failed after 5 retries datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 1/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 2/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 3/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 4/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 5/5) datalib - socket() failed after 5 retries datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 1/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 2/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 3/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 4/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 5/5) datalib - socket() failed after 5 retries datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 1/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 2/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 3/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 4/5) datalib - socket connect failed: Network is unreachable datalib - socket() failed! do_config 109 (retry 5/5) datalib - socket() failed after 5 retries Checking env partition first ... /dev/mem opened. Memory mapped at address 0xb6fa5000. Value at address 0x102D000 (0xb6fa5000): 0x4801 Written 0x4902; readback 0x4902 /dev/mem opened. Memory mapped at address 0xb6f7a000. Value at address 0x102E000 (0xb6f7a000): 0x4801 Written 0x4902; readback 0x49atherosgpio init LED = 64, 63,54 ,53, 57,60 02 /dev/mem opened. Memory mapped at address 0xb6ff4000. Value at address 0x103A000 (0xb6ff4000): 0x20C Written 0x4902; readback 0x4902 /dev/mem opened. Memory mapped at address 0xb6fc7000. Value at address 0x103B000 (0xb6fc7000): 0x208 Written 0x4902; readback 0x4902 The region number is: 0x0002 REGION: WW WPSPIN: 33598291 sn:50K174580110C SN: 50K174580110C lan mac: a0:40:a0:70:09:e6 wlan 2g mac: a6:40:a0:70:09:e6 wan mac: a0:40:a0:70:09:e7 wlan5g mac: a0:40:a0:70:09:e8 wlan2nd5g mac: a0:40:a0:70:09:e9 bt mac: a0:40:a0:70:09:ea hw_revision: Invalid MP FW version, please set in mp_fwversion =Link /dev/dni_art => /dev/mmcblk0p12 =Link /dev/dni_language => /dev/mmcblk0p13 =Link /dev/dni_config => /dev/mmcblk0p14 =Link /dev/dni_pot => /dev/mmcblk0p15 =Link /dev/dni_tm => /dev/mmcblk0p16 =Link /dev/dni_fw1 => /dev/mmcblk0p21 Loading data from " config_dev " ... datalib: header->magic is 0x0, not same as 0x20161130... Fail! Resetting to default values ... The data center is Running ... Config commit is not allowed during booting random: nonblocking pool is initialized Generating Rules... Done! QCE50: __qce_init_clk: Unable to get CE core src clk, set to NULL qcrypto 8e20000.qcrypto: Qualcomm Crypto 5.3.1 device found @0x8e20000 qcrypto 8e20000.qcrypto: CE device = 0x0 , IO base, CE = 0xe1140000 , Consumer (IN) PIPE 2, Producer (OUT) PIPE 3 IO base BAM = 0x (null) BAM IRQ 239 Engines Availability = 0x2010453 sps:BAM 0x08e04000 is registered. sps:BAM 0x08e04000 (va:0xe1180000) enabled: ver:0x27, number of pipes:4 QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x0000000008e04000 irq 239 bus_scale_table is NULL qcrypto 8e20000.qcrypto: qcrypto-ecb-aes qcrypto 8e20000.qcrypto: qcrypto-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-ctr-aes qcrypto 8e20000.qcrypto: qcrypto-ecb-des qcrypto 8e20000.qcrypto: qcrypto-cbc-des qcrypto 8e20000.qcrypto: qcrypto-ecb-3des qcrypto 8e20000.qcrypto: qcrypto-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-xts-aes qcrypto 8e20000.qcrypto: qcrypto-sha1 qcrypto 8e20000.qcrypto: qcrypto-sha256 qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha1-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-aes qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-des qcrypto 8e20000.qcrypto: qcrypto-aead-hmac-sha256-cbc-3des qcrypto 8e20000.qcrypto: qcrypto-hmac-sha1 qcrypto 8e20000.qcrypto: qcrypto-hmac-sha256 qcrypto 8e20000.qcrypto: qcrypto-aes-ccm qcrypto 8e20000.qcrypto: qcrypto-rfc4309-aes-ccm qcrypto: FIPS140-2 Known Answer Tests: Skipped clbr: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint client bridge loaded device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com loop: module loaded PPP generic driver version 2.4.2 ess-switch DT exist! switchreg_base_addr: 0xc000000 switchreg_size: 0x80000 switch_access_mode: local bus wan bmp:0x20 ess-psgmii DT exist! mac mode=0 current mac mode = 0 current dts led_source_num is 5 mdio DT exist! ssdk_plat_init start enable ess clk reset ok in probe! PHY ID is 0x4dd0b1 qca probe malibu phy driver succeeded! Dakota Chip version 0x1401 qca-ssdk module init succeeded! tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ********************************************************** * Driver :NSS GMAC Driver for RTL v(3.72a) * Version :1.0 * Copyright :Copyright (c) 2013-2016 The Linux Foundation. All rights reserved. ********************************************************** mdio bus 'mdio-gpio.0' get FAIL.netlink_kernel_create error ... qca-nss-drv.ko is loaded for symbol link dni-qos module init. gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) QCA Hy-Fi multicast installation successfully ip6_tables: (C) 2000-2006 Netfilter Core Team nf_conntrack_rtsp v0.6.21 loading nf_nat_rtsp v0.6.21 loading XHTTP netlink: create netlink OK. ip_set: protocol 6 NET: Registered protocol family 24 ECM init ECM database jhash random seed: 0x103cff31 ECM init complete PPTP driver version 0.8.5 u32 classifier Performance counters on input device check on Actions configured Mirror/redirect action on Loading DNI-ENET driver Ebtables v2.0 registered l2tp_ppp: PPPoL2TP kernel driver, V2.0 ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 . = switch init . cfg02aa45 Config commit is not allowed during booting 62 QoS default rules are Loaded! Config commit is not allowed during booting Config commit is not allowed during booting ssid:ORBI97 passphrase:elegantoboe554 ssid:NETGEAR_ORBI_hidden52 passphrase:LzewabDvLgSI7oKBc6O0z2o9eJGgLfj8wyV4OXJsTX1QOMsRlAaCFBVQ3zYAJlZ Config commit is not allowed during booting Config commit is not allowed during booting Config commit is not allowed during booting Config commit is not allowed during booting Config commit is not allowed during booting Config commit is not allowed during booting Config commit is not allowed during booting /etc/rc.common: /etc/rc.d/S11init-gpio: line 23: syntax error: unexpected "}" EXT4-fs (mmcblk0p35): mounted filesystem without journal. Opts: (null) hyfi_netlink_receive:66:Device not found: br0 hyd: ERROR: Bridge is not attached; start hyfi-bridging first bio: create slab <bio-1> at 1 EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) . = network init SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. device eth1 entered promiscuous mode init.enet: Default LAN MAC is : a0:40:a0:70:09:e6 . Reading all physical volumes. This may take a while... Successfully initialized wpa_supplicant have reset factory,dal partition will be will re-format /dev/mmcblk0p31 contains a ext4 file system last mounted on /tmp/dal on Tue Oct 15 12:18:08 2024 Discarding device blocks: 1024/5120 done Creating filesystem with 5120 1k blocks and 1280 inodes Allocating group tables: 0/1 done Writing inode tables: 0/1 done Creating journal (1024 blocks): done Writing superblocks and filesystem accounting information: 0/1 done EXT4-fs (mmcblk0p31): mounted filesystem with ordered data mode. Opts: (null) mount dal partition successful. 50K174580110C ------------ d2.init:d2 general.fsn ------------ general[0].fsn: 50K174580110C ------------ d2.init:d2 general.fsn ------------ Config commit is not allowed during booting Module name matched: dal_ash LOG level for the dal_ash is: LOG_DEBUG LogToConsole value is: false LogToFile value is: true Log Level changed sucessfully for dal_ash!!! Module name matched: upagent LOG level for the upagent is: LOG_DEBUG LogToConsole value is: false LogToFile value is: true Log Level changed sucessfully for upagent!!! 2788 Enjoy !!!!! D2D running 033405:(29): add subscription General (0) 033405:(29): Registering ntf 033405:(29): (De)registering complete boot ************* start_service ************* switch init SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. 033996:(31): add subscription Dilsignature (0) 033996:(31): Registering ntf 033996:(31): (De)registering complete 033996:(31): add subscription General (0) 033996:(31): add subscription DILGeneral (0) 033997:(31): add subscription dalLogCfg (0) 033997:(31): add subscription DILGeneral (0) 033997:(31): add subscription DeviceIdList (0) 033998:(31): add subscription DeviceIdList (0) 033998:(31): add subscription DeviceIdList (0) 033998:(31): add subscription DeviceIdList (0) opmode = normal device eth1 left promiscuous mode br0: port 1(eth1) entered disabled state ********************* have done something about plug off *********************** device eth1 entered promiscuous mode device eth0 entered promiscuous mode SSDK Init OK! operate done. SSDK Init OK! Illegal parameter(s) SSDK Init OK! operate done. IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready net.bridge.bridge-nf-call-custom = 0 hyfi_netlink_receive:108:hyfi: Not attached to bridge br0 Error running command IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready net.bridge.bridge-nf-call-custom = 1 Deleting static route ... Done! Adding static route ... Done! br0: port 1(eth1) entered forwarding state br0: port 1(eth1) entered forwarding state IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready udhcp server (v0.9.8) started SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. IPv6: ADDRCONF(NETDEV_UP): brwan: link is not ready [wlan]===time:Tue Oct 28 05:36:28 UTC 2025 command:wlan countrycode============== [wlan]===time:Tue Oct 28 05:36:30 UTC 2025 command:wlan updateconf boot============== [wlan]=========time:Tue Oct 28 05:36:30 UTC 2025 wlan updateconf start====== SSDK Init OK! operate done. SSDK Init OK! operate done. SSDK Init OK! operate done. EXT4-fs (mmcblk0p27): recovery complete EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts: (null) [wlan]=========time:Tue Oct 28 05:36:35 UTC 2025 wlan updateconf end====== QCA post_updateconf_qcawifi 044247:(35): add subscription FeatureCfg (0) 044247:(35): Registering ntf 044248:(35): (De)registering complete Run BASE_BOARD net-scan config...The attached devices demo is Running ... Support ssdk switch mac table check function. Config commit is not allowed during booting 045131:(40): add subscription DILGeneral (0) 045131:(40): Registering ntf 045132:(40): (De)registering complete 045140:(41): add subscription Dilsignature (0) 045140:(41): Registering ntf 045141:(41): (De)registering complete The telnetenable is running ... net-scan backgroud start scan... [net-scan] start scan devices... hyd: some interface(s) are not ready. hyd: ERROR: Private network interface checking failed IPv6: ADDRCONF(NETDEV_UP): brwan: link is not ready [wlan]===time:Tue Oct 28 05:36:37 UTC 2025 command:wlan up============== [wlan]=========time:Tue Oct 28 05:36:37 UTC 2025 wlan up start================== Config commit is not allowed during booting qcawifi: enable radio wifi0 __mm_init_module ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_spectral: Version 2.0.0 Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_tx99: Version 2.0 Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_da_pci: (Atheros/multi-bss) *********** IPQ4019 *************Wifi0 CPU frequency 250000000 hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn dba404c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type b __ol_ath_attach: dev name wifi0 ol_ath_attach interface_id 0 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xb, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3803] Get Caldata for wifi0. qdf_fs_read[59], Open File /tmp/wifi0.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 8411file size:12064=====checksum:0==== qc98xx_verify_checksum: flash checksum passed: 0x 6b8 ol_transfer_bin_file 3879: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 4680 First OTP send param 8000 ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660 ol_ath_download_firmware:##Board Id 20 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi0: Selecting board data file name boardData_1_0_IPQ4019_DK04_2G.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_2G.bin ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 4680 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1610612717 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:100109 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 162035 Target address 417c80 scn=dba404c0 target_write_addr=417c80 seg_info=df549210 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 1, Download data len 368384 ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle dc500000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :dc608000-htc_create: (0xde916000) htc_wmi_init() HT Create . de916000 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xdc60c578hif_completion_thread_startup: pipe_num:3 pipe_info:0xdc60c650hif_completion_thread_startup: pipe_num:4 pipe_info:0xdc60c698 -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev db398000 hrtimer db39c890 htt_alloc_peer_map_mem : Alloc Success : host q vaddr ddc66000 paddr 9dc66000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from da820000 Firmware_Build_Number:14 FW wireless modes: 0x680c num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa btcoex_support 0, wlan_prio_gpio 0, coex_gpio_pin 0 0 0 wmi_service_coex_gpio 1, wmi_service_4_wire_coex_support 1, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, idx 6 req 5 num_units 0 num_unit_info 2 unit size 2044 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2044, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x9c554000 chunk 1 len 54272 requested , ptr 0x9a880000 chunk 2 len 217088 requested , ptr 0x9a8c0000 chunk 3 len 395064 requested , ptr 0x9a900000 chunk 4 len 107520 requested , ptr 0x9a8a0000 chunk 5 len 6144 requested , ptr 0x9a818000 chunk 6 len 1085364 requested , ptr 0x9aa00000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 0 ol_ath_attach() connect HTC. bypasswmi : 0 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === udhcp client (v0.9.8) startedNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 no 6RD parameters available, so unset 6rd related config ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: 2884: Netlink socket created:dea06400 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_attach: called; ptr=dab6998c, radar_info=dc51bc30 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[1] ..ptr:bf9d6c0c ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =dc546400 ic->ic_wrap_com=dc546400 &wrap_com->wc_devt=dc546400 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_ahb_probe num_radios=0, wifi_radios[0].sc = dba404c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr *********** IPQ4019 *************Wifi1 CPU frequency 250000000 hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn da9c04c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type b __ol_ath_attach: dev name wifi1 ol_ath_attach interface_id 1 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xb, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3803] Get Caldata for wifi1. qdf_fs_read[59], Open File /tmp/wifi1.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 8414file size:12064=====checksum:0==== qc98xx_verify_checksum: flash checksum passed: 0x9529 ol_transfer_bin_file 3879: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 4680 First OTP send param 8000 ol_ath_download_firmware :First OTP download and Execute is good address:0x5400 return param 4660 ol_ath_download_firmware:##Board Id 21 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi1: Selecting board data file name boardData_1_0_IPQ4019_DK04_5G.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_5G.bin ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 4680 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1610612717 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:100109 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 162035 Target address 417c80 scn=da9c04c0 target_write_addr=417c80 seg_info=dc540810 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 1, Download data len 368384 Config commit is not allowed during booting Config commit is not allowed during booting [net-scan]receive SIG10.. [fing-devices]receive SIG10.. EXT4-fs (mmcblk0p36): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (mmcblk0p36): couldn't mount as ext2 due to feature incompatibilities EXT4-fs (mmcblk0p36): recovery complete EXT4-fs (mmcblk0p36): mounted filesystem with ordered data mode. Opts: (null) [1761629802]collect installation event: sysReboot, /tmp/router-analytics/ra_data/installation/0032 Config commit is not allowed during booting 16+0 records in 16+0 records out 261088 bytes (255.0KB) copied, 0.008204 seconds, 30.3MB/s 1+0 records in 1+0 records out 16384 bytes (16.0KB) copied, 0.001298 seconds, 12.0MB/s 1+0 records in 1+0 records out 16384 bytes (16.0KB) copied, 0.001012 seconds, 15.4MB/s DIL Total device num=0 1+0 records in 1+0 records out 16384 bytes (16.0KB) copied, 0.001104 seconds, 14.2MB/s 1+0 records in 1+0 records out 16384 bytes (16.0KB) copied, 0.001172 seconds, 13.3MB/s mmc0: Starting tests of card mmc0:0001... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 6. Basic proc read (with data verification)... mmc0: Result: OK mmc0: Tests completed. mmc0: Starting tests of card mmc0:0001... mmc0: Test case 5. Basic proc write (with data verification)... mmc0: Result: ERROR (-22) mmc0: Tests completed. ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle dac22000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :dab20000-htc_create: (0xdba09800) htc_wmi_init() HT Create . dba09800 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xdab24578hif_completion_thread_startup: pipe_num:3 pipe_info:0xdab246504096+hif_completion_thread_startup: pipe_num:4 pipe_info:0xdab246980 records in 4096+0 records out 2097152 bytes (2.0MB) copied, 0.074427 seconds, 26.9MB/s -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev d9b08000 hrtimer d9b0c890 htt_alloc_peer_map_mem : Alloc Success : host q vaddr da1f4000 paddr 9a1f4000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d9780000 Firmware_Build_Number:14 FW wireless modes: 0x1f9001 num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 Config commit is not allowed during booting ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, idx 6 req 5 num_units 0 num_unit_info 2 unit size 2044 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2044, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x9a2a0000 chunk 1 len 54272 requested , ptr 0x9a240000 chunk 2 len 217088 requested , ptr 0x99000000 chunk 3 len 395064 requested , ptr 0x99080000 chunk 4 len 107520 requested , ptr 0x997e0000 chunk 5 len 6144 requested , ptr 0x9a88e000 chunk 6 len 1085364 requested , ptr 0x99200000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 mkdir: can't create directory '/tmp/router-analytics': File exists Cannot connect to server , will try 60s later!!Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1 ol_ath_attach() connect HTC. bypasswmi : 0 ol_ath_attach: low_5ghz: 5490 high_5gh: 5850 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === DNI: Freq:5825 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Add VHT80 channel: 5690 Add VHT80 channel: 5775 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5745 POWERLIMIT DISABLE === DNI: Freq:5765 POWERLIMIT DISABLE === DNI: Freq:5785 POWERLIMIT DISABLE === DNI: Freq:5805 POWERLIMIT DISABLE === Skipping VHT80 channel 5825 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=106 freq=122 freq=138 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: Offload using existing sock dea06400 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_attach: called; ptr=d93a998c, radar_info=dc51bc30 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[2] ..ptr:bf9d6c0c ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =dc54e600 ic->ic_wrap_com=dc54e600 &wrap_com->wc_devt=dc54e600 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_ahb_probe num_radios=1, wifi_radios[1].sc = da9c04c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr ath_ol_pci: (Atheros/multi-bss) hif_pci_enable_bus: con_mode = 0x0, device_id = 0x56PCI: enabling device 0000:00:00.0 (0144 -> 0147) PCI: enabling device 0000:01:00.0 (0140 -> 0142) hif_pci_enable_bus: hif_enable_pci done *********** QCA9888 *************hif_pci_enable_bus: hif_type = 0xe, target_type = 0xchif_pci_enable_bus: hif_pci_probe_tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW signal, retries = 1hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_set_hia_extnd: E chip_id 0xc chip_revision 0x0 CLOCK PLL skipped hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn d90404c0 nss is not enabled on this platform nss register id -1 offload mode enabled = 0 nss config 0 Target Type c __ol_ath_attach: dev name wifi2 ol_ath_attach interface_id 2 xt_CT: netfilter: NOTRACK target is deprecated, use CT instead or upgrade iptables Starting Firewall... Done! ol_target_init() BMI inited. Switching to Tx Mode-1 Threshold 280 ol_target_init() BMI Get Target Info. Chip id: 0xc, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3803] Get Caldata for wifi2. qdf_fs_read[59], Open File /tmp/wifi2.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 8417file size:12064=====checksum:0==== qc98xx_verify_checksum: flash checksum passed: 0x9d0b ol_transfer_bin_file 3879: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 9084 Group schedule demon is running! Acl timer init!! Init device timer!! Update guest schedule 0 status 1 for group 11!! Init devices successfull First OTP send param 8000 Oct 28 05:36:44 miniupnpd[7262]: could not open lease file: /tmp/upnp.leases Oct 28 05:36:44 miniupnpd[7262]: ioctl(s, SIOCGIFADDR, ...): Cannot assign requested address Oct 28 05:36:44 miniupnpd[7262]: Cannot get IP address for ext interface brwan. Network is down Oct 28 05:36:44 miniupnpd[7262]: HTTP listening on port 56688 Oct 28 05:36:44 miniupnpd[7262]: no HTTP IPv6 address, disabling IPv6 Oct 28 05:36:44 miniupnpd[7262]: Listening for NAT-PMP/PCP traffic on port 5351 time zone index is : 0 Run NTP Client with setting: pri:time-g.netgear.com sec:time-h.netgear.com ol_ath_download_firmware :First OTP download and Execute is good address:0x6000 return param 4660 ol_ath_download_firmware:##Board Id 24 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi2: Selecting board data file name boardData_2_0_QCA9888_5G_YA105.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9888/hw.2/boardData_2_0_QCA9888_5G_YA105.bin ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 0, Download data len 9084 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version 0 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully Swap: bytes_left to copy: fw:16; dma_page:26209 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 235935 Target address 41a8a8 scn=d90404c0 target_write_addr=41a8a8 seg_info=dabfb710 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3684: downloading file 1, Download data len 373600 [wlan]===time:Tue Oct 28 05:36:45 UTC 2025 command:wlan stainfo============== will set soap sync psk:481eaced5ef13645c5e19af81ee9d77bf55e96017a5ac163a29880104bd1c4a0 Config commit is not allowed during booting EXT4-fs (mmcblk0p35): mounted filesystem without journal. Opts: (null) Switching to Tx Mode-1 Threshold 280 ol_target_init() Download FW done. ol_ath_attach() WMI attached. wmi_handle d9198000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :d9398000-htc_create: (0xdba0a800) htc_wmi_init() HT Create . dba0a800 htc_wmi_init 7549 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xd939c578hif_completion_thread_startup: pipe_num:3 pipe_info:0xd939c650hif_completion_thread_startup: pipe_num:4 pipe_info:0xd939c698 -HWT Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev d8528000 hrtimer d852c890 htt_alloc_peer_map_mem : Alloc Success : host q vaddr d8532000 paddr 98532000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d81a0000 Firmware_Build_Number:14 FW wireless modes: 0x7f9001 num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339979fa vht_supp_mcs:0x0000fffa wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 896 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 896, idx 4 req 5 num_units 0 num_unit_info 2 unit size 1948 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 4 num_units 531 unit_len 1948, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x99314000 chunk 1 len 54272 requested , ptr 0x98200000 chunk 2 len 217088 requested , ptr 0x98240000 chunk 3 len 475776 requested , ptr 0x98280000 chunk 4 len 1034388 requested , ptr 0x98300000 ol_ath_service_ready_event[4264] WAPI MBSSID 2 Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 2 ol_ath_attach() connect HTC. bypasswmi : 0 ol_ath_attach: low_5ghz: 5150 high_5gh: 5330 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Add VHT80 channel: 5690 Add VHT80 channel: 5775 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === freq=58 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: Offload using existing sock dea06400 SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_attach: called; ptr=d821998c, radar_info=dc51bc10 dfs_attach: event log enabled by default >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[3] ..ptr:bf9d6c0c ath_lowi_if_netlink_init NETLINK_KERNEL_CREATE FAILED LOWI driver intferace socket init failed __investigate__ osif_wrap_attach:441 osif wrap attached osif_wrap_devt_init:402 osif wrap dev table init done Wrap Attached: Wrap_com =dc6bca00 ic->ic_wrap_com=dc6bca00 &wrap_com->wc_devt=dc6bca00 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_pci_probe num_radios=2, wifi_radios[2].sc = d90404c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 +hif_update_pipe_callback pipeid 8 -hif_update_pipe_callback __sa_init_module No Direct-Attach chipsets found. Removing athdebug proc file ath_dev: driver unloaded ath_tx99: driver unloaded ath_rate_atheros: driver unloaded ath_hal: driver unloaded isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === DNI: Freq:2412 POWERLIMIT DISABLE === DNI: Freq:2417 POWERLIMIT DISABLE === DNI: Freq:2422 POWERLIMIT DISABLE === DNI: Freq:2427 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2432 POWERLIMIT DISABLE === DNI: Freq:2437 POWERLIMIT DISABLE === DNI: Freq:2442 POWERLIMIT DISABLE === DNI: Freq:2447 POWERLIMIT DISABLE === DNI: Freq:2452 POWERLIMIT DISABLE === DNI: Freq:2457 POWERLIMIT DISABLE === DNI: Freq:2462 POWERLIMIT DISABLE === DNI: Freq:2467 POWERLIMIT DISABLE === DNI: Freq:2472 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 wlan_vap_create : enter. devhandle=0xdba404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = a6:40:a0:70:09:e6: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xdba404c0, vap=0xdc6a8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling TSO bit for the vap ath0 features 4000 Enabling LRO bit for the vap ath0 features 4000 VAP device ath0 created osifp: (de93b4c0) os_if: (dc6a8000) bio: create slab <bio-1> at 1 siwfreq Set freq vap 0 stop send + dc6a8000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7719 Comm:iwconfig :: PPID:6409 Comm:wlan <=< Set freq vap 0 stop send -dc6a8000 EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) Set wait done --dc6a8000 ME Pool succesfully initialized vaddr - dc6c0000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-0(ath0):set SIOC80211NWID, 2 characters DES SSID SET=on vap-0(ath0):set SIOC80211NWID, 6 characters DES SSID SET=ORBI97 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0007040000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath0 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2742 Comm:hostapd :: PPID:1 Comm:procd <=< Sending SCAN START cmd br0: port 2(ath0) entered forwarding state br0: port 2(ath0) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath0 OK ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9207a4 arg=dab80000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdc6a8000 send_vdev_down_cmd_non_tlv for vap 0 (dc500000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7858 Comm:iwpriv :: PPID:6409 Comm:wlan <=< Sending SCAN START cmd wlan_vap_create : enter. devhandle=0xdba404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 1 Type = 1, Subtype = 0 VAP Addr = aa:40:a0:70:09:e6: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xdba404c0, vap=0xd9190000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath01 features 4000 Enabling SG bit for the vap ath01 features 4000 Enabling SG bit for the vap ath01 features 4000 Enabling TSO bit for the vap ath01 features 4000 Enabling LRO bit for the vap ath01 features 4000 VAP device ath01 created osifp: (d9324cc0) os_if: (d9190000) siwfreq Set freq vap 0 stop send + dc6a8000 ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9207a4 arg=dab80000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xdc6a8000 send_vdev_down_cmd_non_tlv for vap 0 (dc500000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7877 Comm:iwconfig :: PPID:6409 Comm:wlan <=< Set freq vap 0 stop send -dc6a8000 Set wait done --dc6a8000 Set freq vap 1 stop send + d9190000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7877 Comm:iwconfig :: PPID:6409 Comm:wlan <=< Set freq vap 1 stop send -d9190000 Set wait done --d9190000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7877 Comm:iwconfig :: PPID:6409 Comm:wlan <=< Sending SCAN START cmd ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9207a4 arg=dab80000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdc6a8000 send_vdev_down_cmd_non_tlv for vap 0 (dc500000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7889 Comm:iwpriv :: PPID:6409 Comm:wlan <=< Sending SCAN START cmd vap-1(ath01):set SIOC80211NWID, 2 characters DES SSID SET=on vap-1(ath01):set SIOC80211NWID, 21 characters DES SSID SET=NETGEAR_ORBI_hidden52 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0407040000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 Switching to Tx Mode-1 Threshold 280 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 0 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 device ath01 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath01 DEVICE IS DOWN ifname=ath01 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9190000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2742 Comm:hostapd :: PPID:1 Comm:procd <=< br0: port 3(ath01) entered forwarding state br0: port 3(ath01) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath01 OK osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9190000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7960 Comm:iwpriv :: PPID:6409 Comm:wlan <=< wlan_vap_create : enter. devhandle=0xdba404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 2 Type = 1, Subtype = 0 VAP Addr = ae:40:a0:70:09:e6: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xdba404c0, vap=0xd7c70000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath02 features 4000 Enabling SG bit for the vap ath02 features 4000 Enabling SG bit for the vap ath02 features 4000 Enabling TSO bit for the vap ath02 features 4000 Enabling LRO bit for the vap ath02 features 4000 VAP device ath02 created osifp: (de93dcc0) os_if: (d7c70000) siwfreq Set freq vap 0 stop send + dc6a8000 ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9207a4 arg=dab80000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xdc6a8000 send_vdev_down_cmd_non_tlv for vap 0 (dc500000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7973 Comm:iwconfig :: PPID:6409 Comm:wlan <=< Set freq vap 0 stop send -dc6a8000 Set wait done --dc6a8000 Set freq vap 1 stop send + d9190000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7973 Comm:iwconfig :: PPID:6409 Comm:wlan <=< Set freq vap 1 stop send -d9190000 Set wait done --d9190000 Set freq vap 2 stop send + d7c70000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7973 Comm:iwconfig :: PPID:6409 Comm:wlan <=< Set freq vap 2 stop send -d7c70000 Set wait done --d7c70000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7973 Comm:iwconfig :: PPID:6409 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9190000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7973 Comm:iwconfig :: PPID:6409 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9207a4 arg=dab80000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdc6a8000 send_vdev_down_cmd_non_tlv for vap 0 (dc500000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7985 Comm:iwpriv :: PPID:6409 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9190000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7985 Comm:iwpriv :: PPID:6409 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9207a4 arg=dab80000 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdc6a8000 send_vdev_down_cmd_non_tlv for vap 0 (dc500000) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7993 Comm:iwpriv :: PPID:6409 Comm:wlan <=< Sending SCAN START cmd osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9190000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:7993 Comm:iwpriv :: PPID:6409 Comm:wlan <=< EXT4-fs (mmcblk0p35): mounted filesystem without journal. Opts: (null) WARNING: Fragmentation with HT mode NOT ALLOWED!! vap-2(ath02):set SIOC80211NWID, 2 characters DES SSID SET=on vap-2(ath02):set SIOC80211NWID, 13 characters DES SSID SET=NETGEAR-Guest ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0007040000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath02 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath02 DEVICE IS DOWN ifname=ath02 osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd7c70000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2742 Comm:hostapd :: PPID:1 Comm:procd <=< br0: port 4(ath02) entered forwarding state br0: port 4(ath02) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath02 OK osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd7c70000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8061 Comm:iwpriv :: PPID:6409 Comm:wlan <=< ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9207a4 arg=dab80000 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xdc6a8000 send_vdev_down_cmd_non_tlv for vap 0 (dc500000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8083 Comm:ifconfig :: PPID:6409 Comm:wlan <=< Sending SCAN START cmd br0: port 2(ath0) entered disabled state osif_vap_init: Scan in progress.. Cancelling it. vap: 0xdc6a8000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8087 Comm:ifconfig :: PPID:6409 Comm:wlan <=< br0: port 2(ath0) entered forwarding state br0: port 2(ath0) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath0 ol_scan_unregister_event_handler: Failed to unregister evhandler=bf9207a4 arg=dab80000 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xd9190000 send_vdev_down_cmd_non_tlv for vap 1 (dc500000) Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8102 Comm:ifconfig :: PPID:6409 Comm:wlan <=< Sending SCAN START cmd br0: port 3(ath01) entered disabled state osif_vap_init: Scan in progress.. Cancelling it. vap: 0xd9190000 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8103 Comm:ifconfig :: PPID:6409 Comm:wlan <=< br0: port 3(ath01) entered forwarding state br0: port 3(ath01) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath01 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xd7c70000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8104 Comm:ifconfig :: PPID:6409 Comm:wlan <=< br0: port 4(ath02) entered disabled state qcawifi: enable radio wifi1 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === DNI: Freq:5700 POWERLIMIT DISABLE === DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5660 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === DNI: Freq:5680 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 DNI: Freq:5500 POWERLIMIT DISABLE === DNI: Freq:5520 POWERLIMIT DISABLE === DNI: Freq:5540 POWERLIMIT DISABLE === DNI: Freq:5560 POWERLIMIT DISABLE === DNI: Freq:5580 POWERLIMIT DISABLE === DNI: Freq:5600 POWERLIMIT DISABLE === DNI: Freq:5620 POWERLIMIT DISABLE === DNI: Freq:5640 POWERLIMIT DISABLE === Skipping VHT80 channel 5660 Skipping VHT80 channel 5680 Skipping VHT80 channel 5700 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=106 freq=122 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 wlan_vap_create : enter. devhandle=0xda9c04c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = a0:40:a0:70:09:e8: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xda9c04c0, vap=0xd7d48000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling TSO bit for the vap ath1 features 4000 Enabling LRO bit for the vap ath1 features 4000 VAP device ath1 created osifp: (de9114c0) os_if: (d7d48000) siwfreq Set freq vap 0 stop send + d7d48000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8257 Comm:iwconfig :: PPID:8173 Comm:wlan <=< Set freq vap 0 stop send -d7d48000 Set wait done --d7d48000 vap-0(ath1):set SIOC80211NWID, 2 characters DES SSID SET=on vap-0(ath1):set SIOC80211NWID, 21 characters DES SSID SET=NETGEAR_ORBI_hidden52 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0407040000000000 -----su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 ----------------------------------- su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 device ath1 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 bio: create slab <bio-1> at 1 EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) DEVICE IS DOWN ifname=ath1 DEVICE IS DOWN ifname=ath1 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2742 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - EXT4-fs (mmcblk0p35): mounted filesystem without journal. Opts: (null) ol_vdev_start_resp_ev for vap 0 (dac22000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 5(ath1) entered forwarding state br0: port 5(ath1) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath1 OK qcawifi: enable radio wifi2 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === DNI: Freq:5180 POWERLIMIT DISABLE === DNI: Freq:5200 POWERLIMIT DISABLE === DNI: Freq:5220 POWERLIMIT DISABLE === DNI: Freq:5240 POWERLIMIT DISABLE === DNI: Freq:5260 POWERLIMIT DISABLE === DNI: Freq:5280 POWERLIMIT DISABLE === DNI: Freq:5300 POWERLIMIT DISABLE === DNI: Freq:5320 POWERLIMIT DISABLE === freq=58 set TXBF_SND_PERIOD: value 100 wmi_status 0 Disconnect_timeout value entered:10 reconfiguration_timeout value entered:60 wlan_vap_create : enter. devhandle=0xd90404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = a0:40:a0:70:09:e9: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd90404c0, vap=0xd7da8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling TSO bit for the vap ath2 features 4000 Enabling LRO bit for the vap ath2 features 4000 VAP device ath2 created osifp: (dba0f4c0) os_if: (d7da8000) siwfreq Set freq vap 0 stop send + d7da8000 Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8576 Comm:iwconfig :: PPID:8484 Comm:wlan <=< Set freq vap 0 stop send -d7da8000 Set wait done --d7da8000 ME Pool succesfully initialized vaddr - d7e00000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST vap-0(ath2):set SIOC80211NWID, 2 characters DES SSID SET=on vap-0(ath2):set SIOC80211NWID, 6 characters DES SSID SET=ORBI97 ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0007040000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath2 entered promiscuous mode ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 DEVICE IS DOWN ifname=ath2 DEVICE IS DOWN ifname=ath2 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2742 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (d9198000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/3 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (d9198000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 6(ath2) entered forwarding state br0: port 6(ath2) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath2 OK wlan_vap_create : enter. devhandle=0xd90404c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 1 Type = 1, Subtype = 0 VAP Addr = a6:40:a0:70:09:e9: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xd90404c0, vap=0xd7e30000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath21 features 4000 Enabling SG bit for the vap ath21 features 4000 Enabling SG bit for the vap ath21 features 4000 Enabling TSO bit for the vap ath21 features 4000 Enabling LRO bit for the vap ath21 features 4000 VAP device ath21 created osifp: (de93d4c0) os_if: (d7e30000) bio: create slab <bio-1> at 1 siwfreq EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8711 Comm:iwpriv :: PPID:8484 Comm:wlan <=< Config commit is not allowed during booting vap 0: drop SWBA event, since vap is not active STOPPED EVENT for vap 0 (d9198000) send_vdev_down_cmd_non_tlv for vap 0 (d9198000) OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (d9198000) Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:8721 Comm:hotplug-call :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (d9198000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 vap-1(ath21):set SIOC80211NWID, 2 characters DES SSID SET=on vap-1(ath21):set SIOC80211NWID, 13 characters DES SSID SET=NETGEAR-Guest ---------------------------------------- Adding or updating following vendor ie Vendor IE info Ioctl Csu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 MD id : 31 ID : dd Len (OUI+ Pcapdata) in Bytes : 11 OUI : 0su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 1 0146c Private capibility_data : 0007040000000000 -----su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 ----------------------------------- Init wifison script su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 device ath21 entered promiscuous mode Config commit is not allowed during booting ieee80211_ioctl_siwmode: imr.ifm_active=18875008, new mode=3, valid=1 DEVICE IS DOWN ifname=ath21 DEVICE IS DOWN ifname=ath21 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:2742 Comm:hostapd :: PPID:1 Comm:procd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 1 (d9198000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/3 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 1 (d9198000) ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 7(ath21) entered forwarding state br0: port 7(ath21) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath21 OK Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:8868 Comm:ifconfig :: PPID:8484 Comm:wlan <=< STOPPED EVENT for vap 1 (d9198000) send_vdev_down_cmd_non_tlv for vap 1 (d9198000) br0: port 7(ath21) entered disabled state iface_mgr: ifacemgr_load_conf_file: 218: No STA VAPs are configured a6:40:a0:70:09:e6 a0:40:a0:70:09:e8 iface_mgr: ifacemgr_conn_to_global_wpa_s: 248: connected to global wpa_s iface_mgr: ifacemgr_display_updated_config: 560: Mode:3 timeout:60 Config commit is not allowed during booting Config commit is not allowed during booting Config commit is not allowed during booting Config commit is not allowed during booting [1761629820]collect installation event: soap server up, /tmp/router-analytics/ra_data/installation/0033 Config commit is not allowed during booting [uci2cfg] Start update config to cfg [wlan]=========time:Tue Oct 28 05:37:02 UTC 2025 wlan up end================== QCA post_lock_qcawifi Restart wsplcd after wlan up [WSPLCD init] After updateconf lock check DHCPv6 client is not running! Return DHCPv6 client is not running! Return Stopping Firewall... IPv6 Done! the ipv6 wan type is disable [wlan]===time:Tue Oct 28 05:37:04 UTC 2025 command:wlan retrycheck============== [uci2cfg] Start update config to cfg ME Pool succesfully initialized vaddr - d7580000 paddr - 0 num_elems = 1424 buf_size - 64 pool_size = 102528 Enable MCAST_TO_UCAST send_vdev_down_cmd_non_tlv for vap 0 (dc500000) mlme_create_infra_bss : Overriding HT40 channel with HT20 channel OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 mlme_create_infra_bss : Overriding HT40 channel with HT20 channel OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 ol_vdev_start_resp_ev for vap 0 (dc500000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/2 :: PPID:1 Comm:procd <=< su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (dc500000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_vdev_start_resp_ev for vap 1 (dc500000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:74 Comm:kworker/2:1 :: PPID:2 Comm:kthreadd <=< su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 1 (dc500000) [wlan]===time:Tue Oct 28 05:37:07 UTC 2025 command:wlan retrycheck============== [wsplcd]WLAN interface is not ready net.bridge.bridge-nf-call-custom = 1 128+0 records in 128+0 records out 65536 bytes (64.0KB) copied, 0.017315 seconds, 3.6MB/s cert.info ca.crt dh1024.pem client.crt client.key server.crt server.key [uci2cfg] Start update config to cfg Starting Firewall... Done! traffic_meter start : Router mode, start trafficmeter. EXT4-fs (mmcblk0p28): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (mmcblk0p28): couldn't mount as ext2 due to feature incompatibilities EXT4-fs (mmcblk0p28): recovery complete EXT4-fs (mmcblk0p28): mounted filesystem with ordered data mode. Opts: (null) $Shutting down igmpproxy: New soap mechanism is on ! The soap_agent demo is Running ... [soap_checkfw]curl_expect_time_hm=6:19 hyd: starting daemon 079806:(62): add subscription CircleCfgInternal (0) 079806:(62): Registering ntf 079807:(62): (De)registering complete 079807:(62): add subscription sealServiceStateUpdates (0) 079809:(62): add subscription CircleCfgInternal (0) 079809:(62): add subscription General (0) 079809:(62): add subscription dalLogCfg (0) 079810:(62): add subscription CircleCfgInternal (0) 079810:(62): add subscription CircleDebug (0) 079825:(64): add subscription CircleStatus (0) 079825:(64): Registering ntf 079825:(64): (De)registering complete 079830:(64): add subscription CircleStatus (0) 079830:(64): add subscription CircleDebug (0) 079831:(64): add subscription dalLogCfg (0) 079831:(64): add subscription RADebugLog (0) 080073:(68): add subscription ArmorStatus (0) 080073:(68): Registering ntf 080074:(68): (De)registering complete 080074:(68): add subscription ArmorStatus (0) 080075:(68): add subscription ArmorStatus (0) 080075:(68): add subscription ArmorStatus (0) 080075:(68): add subscription UpStatus (0) 080076:(68): add subscription dalLogCfg (0) 080084:(68): add subscription DALHNotifyCDIL (0) 080084:(68): add subscription DALHNotifyCDUPDATE (0) 080085:(68): add subscription UpStatus (0) 080085:(68): add subscription RADebugLog (0) 080085:(68): add subscription DALHNotifyNDN (0) 080086:(68): add subscription DALHNotifyDTN (0) 080088:(68): add subscription BSTCfg (0) 080089:(68): add subscription UpStatus (0) 080089:(68): add subscription UpStatus (0) 080089:(68): add subscription CircleCfgInternal (0) 080090:(68): add subscription UpStatus (0) 080090:(68): add subscription CircleCfgInternal (0) 080091:(68): add subscription CircleDebug (0) 080091:(68): add subscription CircleDebug (0) 080092:(68): add subscription CircleDebug (0) 080098:(78): add subscription XagentCfg (0) 080098:(78): Registering ntf 080098:(78): (De)registering complete /dev/mmcblk0p33 contains a ext4 file system last mounted on /tmp/mnt/bitdefender on Tue Oct 15 12:19:04 2024 Discarding device blocks: 1024/51200 done Creating filesystem with 51200 1k blocks and 12824 inodes Filesystem UUID: aef6a789-44c4-4c1e-b029-1ed7b3f09e67 Superblock backups stored on blocks: 8193, 24577, 40961 Allocating group tables: 0/7 done Writing inode tables: 0/7 done Creating journal (4096 blocks): done Writing superblocks and filesystem accounting information: 0/7 [wlan]===time:Tue Oct 28 05:37:11 UTC 2025 command:wlan retrycheck============== [ath0] Band steering events being sent to PID:12791 [ath01] Band steering events being sent to PID:12791 [uci2cfg] Start update config to ath1] Band steering events being sent to PID:12791 [ath2] Band steering events being sent to PID:12791 [ath0] Band steering events being sent to PID:12791 [ath2] Band steering events being sent to PID:12791 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 !!! Takes long time--2 NOT to get hyt td s2 result, please check !!! done EXT4-fs (mmcblk0p33): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (mmcblk0p33): couldn't mount as ext2 due to feature incompatibilities EXT4-fs (mmcblk0p33): mounted filesystem with ordered data mode. Opts: (null) bin/ bin/bdcrypto bin/bdupd bitdefender-release etc/ etc/certs/ etc/certs/ca-certificates.crt etc/bdupd.server.sample etc/logging/ etc/logging/bdupd.json etc/logs-pub.pem etc/bdupd-pub.pem share/ share/scripts/ share/scripts/archive_logs.sh var/ var/tmp/ var/tmp/.keep var/log/ var/log/.keep var/run/ var/run/.keep var/upd/ var/upd/.keep [bdupd] do ping netgear... restart the daemon telnetenable for Thin client !!! The telnetenable is running ... [wlan]===time:Tue Oct 28 05:37:14 UTC 2025 command:wlan retrycheck============== wsplcd: starting daemon net.ipv4.neigh.default.gc_reap_limit = 100 restart klogd process [Orbi]***boot done*** [wifi-listener] Starting daemon [ arlo ] arlo list not found bdbrokerd is not up, delay 2s Restart hyd after wlan up [libstorage] Loop checking wlan LOCK [libstorage] Create wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Create wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Create wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Create wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Create wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Create wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Create wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Loop checking wlan LOCK [libstorage] Create wlan LOCK [WSPLCD] Start update config to datalib Saving Data... from parentid: 14466, parent process: (wifison.sh),presentid: 15005,present: (config) bdbrokerd is not up, delay 2s Done! Starting Firewall... Done! 089618:(62): remove subscription CircleCfgInternal (0) 089618:(62): remove subscription CircleDebug (0) 089618:(62): remove subscription General (0) 089618:(62): remove subscription sealServiceStateUpdates (0) 089618:(62): remove subscription dalLogCfg (0) 089618:(62): De-registering ntf 089618:(62): (De)registering complete Loader version 1.2.2 started with nostart option trusted certs file = /etc/ssl/certs/02265526.0 partition = /dev/mmcblk0p28 DEBUG: dpg_cmdline DEBUG: dpg_getppid_name DEBUG: gdb_columns DEBUG: gdb_path DEBUG: various_ldpreload control-firmware will be Running when Internet status is UP !!! CFU will auto check during 00:00~24:00 local time zone (a random number of sec between 0 to of 86400) [wlan]===time:Tue Oct 28 05:37:21 UTC 2025 command:wlan retrycheck============== [WSPLCD] Start update config to datalib [FW UPGRADE][2025-10-28 05:37:21]:[CFU auto check]expect_time == 57531 seconds [CFU auto check]count time:0 whc (repacd): starting WHC auto-configuration whc (repacd): Managed network: 0 whc (repacd): Device type: CAP decrypting 924400 bytes Verified signature decompress_archive: Executing 'tar zxf /tmp/database.tar.gz -C /mnt/circle/' DEBUG: dpg_cmdline DEBUG: dpg_getppid_name DEBUG: gdb_columns DEBUG: gdb_path DEBUG: various_ldpreload ath0 IEEE 802.11ng ESSID:"ORBI97" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden52" ath1 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden52" ath02 IEEE 802.11b ESSID:"NETGEAR-Guest" ath2 IEEE 802.11ac ESSID:"ORBI97" [wlan]===time:Tue Oct 28 05:37:23 UTC 2025 command:wlan retrycheck============== ath21 IEEE 802.11ac ESSID:"NETGEAR-Guest" [WSPLCD] Start update config to datalib decrypting 1475881 bytes !!! Takes long time--2 NOT to get hyt td s2 result, please check !!! Verified signature decompress_archive: Executing 'tar zxf /tmp/sdfiles.tar.gz -C /mnt/circle/' Hostname: RBR40 url_retrieve: Executing 'curl -s -m 180 -o /tmp/circleinfo.txt --cacert /etc/ssl/certs/02265526.0 https://http.fw.updates1.netgear.com/sw-apps/parental-control/circle/rbr40/mr22//circleinfo.txt' hyd: starting daemon [wlan]=========time:Tue Oct 28 05:37:25 UTC 2025 wlan post up ================== [wlan]========= reload netscan ================== net.bridge.bridge-nf-call-custom = 1 [wlan]===time:Tue Oct 28 05:37:26 UTC 2025 command:wlan retrycheck============== [WSPLCD] Start update config to datalib [wlan]===time:Tue Oct 28 05:37:29 UTC 2025 command:wlan retrycheck============== [WSPLCD] Start update config to datalib ath0 IEEE 802.11ng ESSID:"ORBI97" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden52" ath1 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden52" ath02 IEEE 802.11b ESSID:"NETGEAR-Guest" ath2 IEEE 802.11ac ESSID:"ORBI97" ath21 IEEE 802.11ac ESSID:"NETGEAR-Guest" !!! Takes long time--7 NOT to get hyt td s2 result, please check !!! [wlan]===time:Tue Oct 28 05:37:31 UTC 2025 command:wlan retrycheck============== hyd: starting daemon Set backhaul AP OtherBand BSSID Otherband BSSID a0:40:a0:70:9:e8 Otherband BSSID aa:40:a0:70:9:e6 ************vap on**************** [1761629853]collect installation event: wifi on, /tmp/router-analytics/ra_data/installation/0034 Saving Data... from parentid: 1, parent process: (procd),presentid: 6712,present: (install_agent) [ath0] Band steering events being sent to PID:19964 [ath01] Band steering events being sent to PID:19964 [ath1] Band steering events being sent to PID:19964 [ath2] Band steering events being sent to PID:19964 [ath0] Band steering events being sent to PID:19964 [ath2] Band steering events being sent to PID:19964 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 Done! repacd: checking backhaul_ap interface --> network:0 - iface:ath0 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - iface:ath01 - disabled:0 - mode:ap - device:wifi0 - baOrbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20344 Comm:ifconfig :: PPID:16070 Comm:S98repacd <=< ckhaul_ap:1 repacd: checking backhaul_ap interface --> networkSTOPPED EVENT for vap 0 (dac22000) send_vdev_down_cmd_non_tlv for vap 0 (dac22000) :0 - iface:ath1 - disabled:0 - mode:ap - device:wifi1 - backhaul_ap:1 repacd: checking backhaul_ap interface --> network:0 - iface:ath02 - disabled:0 - mode:ap - device:wifi0 - backhaul_ap:0 repacd: checking backhaul_ap interface --> networbr0: port 5(ath1) entered disabled state k:0 - iface:ath2 - disabled:0 - mode:ap - device:wifi2 - backhaul_ap:0 repacd: checking backhaul_ap interface --> network:0 - Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20347 Comm:ifconfig :: PPID:16070 Comm:S98repacd <=< iface:ath21 - disabled:0 - mode:ap - device:wifi2 - backhaul_ap:STOPPED EVENT for vap 1 (dc500000) 0 send_vdev_down_cmd_non_tlv for vap 1 (dc500000) br0: port 3(ath01) entered disabled state Otherband BSSID a0:40:a0:70:9:e8 Otherband BSSID aa:40:a0:70:9:e6 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20376 Comm:ifconfig :: PPID:16070 Comm:S98repacd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 0 (dac22000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: ETSI domain ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: port 5(ath1) entered forwarding state br0: port 5(ath1) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath1 Orbi : osif_vap_init : 6125 wlan_mlme_stop_bss called with flag Zero : Orbi : ieee80211_vap_stop : 826 IEEE80211_STATE_EVENT_DOWN called >=> PID:20379 Comm:ifconfig :: PPID:16070 Comm:S98repacd <=< OL vap_start + VDEV START OL vap_start - ol_vdev_start_resp_ev for vap 1 (dc500000) send_wmm_update_cmd_non_tlv: Orbi : ieee80211_vap_start : 809 IEEE80211_STATE_EVENT_UP called >=> PID:0 Comm:swapper/2 :: PPID:1 Comm:procd <=< su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 1 (dc500000) ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 br0: port 3(ath01) entered forwarding state br0: port 3(ath01) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath01 The sshenable is running ... 106188:(83): add subscription DALHConfig (0) 106188:(83): Registering ntf 106188:(83): (De)registering complete 106189:(83): add subscription DilFWupgrade (0) 106189:(83): add subscription dalLogCfg (0) Saving Data... from parentid: 20432, parent process: (S99XAgent),presentid: 20475,present: (nvram) Done! ------------ XAgent.init:d2 general.fsn ------------ general[0].fsn: 50K174580110C ---------------------------------------------------- ------------ XAgent.init:d2 general.fsn ------------ general[0].fsn: 50K174580110C ---------------------------------------------------- 108562:(104): add subscription XagentCtrl (0) 108563:(104): Registering ntf 108563:(104): (De)registering complete 108657:(107): add subscription BSTCfg (0) 108657:(107): Registering ntf 108657:(107): (De)registering complete 108664:(108): add subscription General (0) 108664:(108): Registering ntf 108664:(108): (De)registering complete 108664:(108): add subscription dalLogCfg (0) Starting Firewall... Done! time zone index is : 0 Run NTP Client with setting: pri:time-g.netgear.com sec:time-h.netgear.com hyd: boot daemon !!! Takes long time--12 NOT to get hyt td s2 result, please check !!! Cannot connect to server , will try 60s later!!ath0 IEEE 802.11ng ESSID:"ORBI97" ath01 IEEE 802.11ng ESSID:"NETGEAR_ORBI_hidden52" ath1 IEEE 802.11ac ESSID:"NETGEAR_ORBI_hidden52" ath02 IEEE 802.11b ESSID:"NETGEAR-Guest" ath2 IEEE 802.11ac ESSID:"ORBI97" ath21 IEEE 802.11ac ESSID:"NETGEAR-Guest" [bdupd]Conn't connect to www.netgear.com hyd: starting daemon !!! Takes long time--2 NOT to get hyt td s2 result, please check !!! ****************Start of ping-netgear******************** [ath0] Band steering events being sent to PID:21821 [ath01] Band steering events being sent to PID:21821 [ath1] Band steering events being sent to PID:21821 [ath2] Band steering events being sent to PID:21821 [ath0] Band steering events being sent to PID:21821 [ath2] Band steering events being sent to PID:21821 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 send_set_bridge_mac_addr_cmd_non_tlv: set bridge_addr a0:40:a0:70:09:e6 !!! Takes long time--7 NOT to get hyt td s2 result, please check !!! url_retrieve: Executing 'curl -s -m 180 -o /tmp/circleinfo.txt --cacert /etc/ssl/certs/02265526.0 https://http.fw.updates1.netgear.com/sw-apps/parental-control/circle/rbr40/mr22//circleinfo.txt' Restart tail -F /tmp/cloud_backend_log process!!! [Daily Check FW]count time:0 [bdupd]Conn't connect to www.netgear.com url_retrieve: Executing 'curl -s -m 180 -o /tmp/circleinfo.txt --cacert /etc/ssl/certs/02265526.0 https://http.fw.updates1.netgear.com/sw-apps/parental-control/circle/rbr40/mr22//circleinfo.txt' cac_timeout cac expired, chan 5540 curr time 4294835 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 (dac22000) __ieee80211_smart_ant_init: Smart Antenna is not supported Cannot connect to server , will try 60s later!![bdupd]Conn't connect to www.netgear.com url_retrieve: Executing 'curl -s -m 180 -o /tmp/circleinfo.txt --cacert /etc/ssl/certs/02265526.0 https://http.fw.updates1.netgear.com/sw-apps/parental-control/circle/rbr40/mr22//circleinfo.txt' Current RAE Download File Path is /sw-apps/router-analytics/ and Router Model: rbr40 url_retrieve: Executing 'curl -s -m 180 -o /tmp/circleinfo.txt --cacert /etc/ssl/certs/02265526.0 https://http.fw.updates1.netgear.com/sw-apps/parental-control/circle/rbr40/mr22//circleinfo.txt' [bdupd]Conn't connect to www.netgear.com 241764:(108): add subscription DALHNotifyBST (0) url_retrieve: Executing 'curl -s -m 180 -o /tmp/circleinfo.txt --cacert /etc/ssl/certs/02265526.0 https://http.fw.updates1.netgear.com/sw-apps/parental-control/circle/rbr40/mr22//circleinfo.txt' [bdupd]Conn't connect to www.netgear.com

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 S - IMAGE_VARIANT_STRING=DAAAANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000023 S - Reset status Config, 0x00000000 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1339 - bootable_media_detect_entry, Start B - 55850 - bootable_media_detect_success, Start B - 55864 - elf_loader_entry, Start B - 58052 - auth_hash_seg_entry, Start B - 60200 - auth_hash_seg_exit, Start B - 94962 - elf_segs_hash_verify_entry, Start B - 209002 - PBL, End B - 209026 - SBL1, Start B - 301078 - pm_device_init, Start D - 9 - pm_device_init, Delta B - 302586 - boot_flash_init, Start D - 37901 - boot_flash_init, Delta B - 344833 - boot_config_data_table_init, Start D - 2765 - boot_config_data_table_init, Delta - (419 Bytes) B - 352609 - clock_init, Start D - 7535 - clock_init, Delta B - 363907 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 B - 367313 - sbl1_ddr_set_params, Start B - 372406 - cpr_init, Start D - 2 - cpr_init, Delta B - 376788 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13171 - sbl1_ddr_set_params, Delta B - 390085 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 461175 - sbl1_wait_for_ddr_training, Start D - 27 - sbl1_wait_for_ddr_training, Delta B - 477571 - Image Load, Start D - 14941 - QSEE Image Loaded, Delta - (262104 Bytes) B - 492939 - Image Load, Start D - 900 - SEC Image Loaded, Delta - (0 Bytes) B - 502788 - Image Load, Start D - 12538 - APPSBL Image Loaded, Delta - (415855 Bytes) B - 515753 - QSEE Execution, Start D - 60 - QSEE Execution, Delta B - 521928 - SBL1, End D - 315015 - SBL1, Delta S - Flash Throughput, 25272 KB/s (678554 Bytes, 26850 us) S - DDR Frequency, 672 MHz U-Boot 2012.07 [Barrier Breaker unknown,unknown] (Dec 01 2016 - 16:53:29) U-boot dni1 V0.3 for DNI HW ID: 29765515; NOR flash 0MB; EMMC flash 4096MB; RAM 512MB smem ram ptable found: ver: 1 len: 3 DRAM: 512 MiB machid : 0x8010001 NAND: ID = 0 Vendor = 0 Device = 0 Nand Flash error. Status = 64 ONFI Read id cmd failed ONFI probe failed SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 0 MiB MMC: qca_mmc: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Valid chip addresses: 27 48 machid: 8010001 flash_type: 1 Net: MAC0 addr:a0:40:a0:70:09:e6 PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Hit any key to stop autoboot: 2 1 0 eth0 PHY0 Down Speed :10 Half duplex eth0 PHY1 Down Speed :10 Half duplex eth0 PHY2 Down Speed :10 Half duplex eth0 PHY3 up Speed :1000 Full duplex eth0 PHY4 Down Speed :10 Half duplex Client starts...[Listening] for ADVERTISE...TTT Retry count exceeded; boot the image as usual nmrp server is stopped or failed ! Read BootPart from BOARD DATA... mmc_read will run command: mmc read 0x871cfba8 0x2a22 0x100 MMC read: dev # 0, block # 10786, count 256 ... 256 blocks read: OK boot partition : 1 BootPart = 1 Loading DNI firmware for checking... MMC read: dev # 0, block # 17954, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18210, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18466, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18722, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 18978, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19234, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19490, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 19746, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20002, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20258, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20514, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 20770, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21026, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21282, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21538, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 21794, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22050, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22306, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22562, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 22818, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23074, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23330, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23586, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 23842, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24098, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24354, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 24610, count 256 ... 256 blocks read: OK MMC read: dev # 0, block # 17954, count 1 ... 1 blocks read: OK ** rootfs address : 0x8435ffc0 ** ## Checking Image at 84000000 ... FIT image found FIT description: ARM OpenWrt FIT (Flattened Image Tree) Image 0 (kernel-1) Description: ARM OpenWrt Linux-6.12.94 Type: Kernel Image Compression: uncompressed Data Start: 0x840000e4 Data Size: 3419792 Bytes = 3.3 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 8df12ab9 Hash algo: sha1 Hash value: 2c50656c534222e8cb3883ac0032f1ca170e2dcd Image 1 (fdt-1) Description: ARM OpenWrt netgear_rbr40 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843430ac Data Size: 18784 Bytes = 18.3 KiB Architecture: ARM Hash algo: crc32 Hash value: ff2a0305 Hash algo: sha1 Hash value: 6fe02b0860ec96c838231d375a2a64976b1c4e1e Default Configuration: 'config@1' Configuration 0 (config@1) Description: OpenWrt netgear_rbr40 Kernel: kernel-1 FDT: fdt-1 ## Checking hash(es) for FIT Image at 84000000 ... Hash(es) for Image 0 (kernel-1): crc32+ sha1+ Hash(es) for Image 1 (fdt-1): crc32+ sha1+ ## Checking Image at 8435ffc0 ... Legacy image found Image Name: OpenWrt fake filesystem Image Type: ARM Linux Filesystem Image (uncompressed) Data Size: 0 Bytes = 0 Bytes Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK mmc_read will run command: mmc read 0x871cfba8 0x2a22 0x100 MMC read: dev # 0, block # 10786, count 256 ... 256 blocks read: OK boot partition : 1 MMC read: dev # 0, block # 17954, count 7680 ... 7680 blocks read: OK ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-6.12.94 Type: Kernel Image Compression: uncompressed Data Start: 0x840000e4 Data Size: 3419792 Bytes = 3.3 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 8df12ab9 Hash algo: sha1 Hash value: 2c50656c534222e8cb3883ac0032f1ca170e2dcd Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt-1' FDT blob subimage Description: ARM OpenWrt netgear_rbr40 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x843430ac Data Size: 18784 Bytes = 18.3 KiB Architecture: ARM Hash algo: crc32 Hash value: ff2a0305 Hash algo: sha1 Hash value: 6fe02b0860ec96c838231d375a2a64976b1c4e1e Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x843430ac Loading Kernel Image ... OK OK Loading Device Tree to 871e8000, end 871ef95f ... OK Using machid 0x8010001 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.94 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 14.3.0 r33051-f5dae5ece4) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Mon Jun 29 12:59:20 2026 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: NETGEAR RBR40 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x0000000087dfffff] [ 0.000000] node 0: [mem 0x0000000087e00000-0x0000000087ffffff] [ 0.000000] node 0: [mem 0x0000000088000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] OF: reserved mem: 0x87e00000..0x87e7ffff (512 KiB) nomap non-reusable smem@87e00000 [ 0.000000] OF: reserved mem: 0x87e80000..0x87ffffff (1536 KiB) nomap non-reusable tz@87e80000 [ 0.000000] percpu: Embedded 14 pages/cpu s25420 r8192 d23732 u57344 [ 0.000000] Kernel command line: root=/dev/mmcblk0p20 blkdevparts=mmcblk0:512K@17K(0:SBL1)ro,512K(0:BOOTCONFIG)ro,512K(0:QSEE)ro,512K(0:QSEE_ALT)ro,256K(0:CDT)ro,256K(0:CDT_ALT)ro,256K(0:DDRPARAMS)ro,256K(0:APPSBLENV)ro,1M(0:APPSBL)ro,1M(0:APPSBL_ALT)ro,256K(0:ART)ro,256K(ARTMTD)ro,2M(language)ro,256K(config)ro,256K(pot)ro,256K(traffic_meter)ro,256K(pot_bak)ro,256K(traffic_meter.bak)ro,3840K(kernel),31488K(rootfs),35328K@9233K(firmware),256K(mtdoops)ro,1457651200(reserved)ro,-(unallocated) rootfstype=squashfs,ext4 rootwait [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000002] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000020] Switching to timer-based delay loop, resolution 20ns [ 0.000323] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000343] CPU: Testing write buffer coherency: ok [ 0.000401] pid_max: default: 32768 minimum: 301 [ 0.013210] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.013235] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.018772] qcom_scm: convention: smc legacy [ 0.020746] Setting up static identity map for 0x80300000 - 0x8030003c [ 0.020971] rcu: Hierarchical SRCU implementation. [ 0.020980] rcu: Max phase no-delay instances is 1000. [ 0.021462] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.022120] smp: Bringing up secondary CPUs ... [ 0.026208] smp: Brought up 1 node, 4 CPUs [ 0.026232] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.026244] CPU: All CPU(s) started in SVC mode. [ 0.027345] Memory: 503448K/524288K available (7996K kernel code, 635K rwdata, 1224K rodata, 1024K init, 255K bss, 19552K reserved, 0K cma-reserved, 0K highmem) [ 0.035019] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.035238] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.035269] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.041784] pinctrl core: initialized pinctrl subsystem [ 0.045180] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.045583] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.046972] thermal_sys: Registered thermal governor 'step_wise' [ 0.047090] cpuidle: using governor ladder [ 0.047130] cpuidle: using governor menu [ 0.070719] cryptd: max_cpu_qlen set to 1000 [ 0.075706] usbcore: registered new interface driver usbfs [ 0.075776] usbcore: registered new interface driver hub [ 0.075833] usbcore: registered new device driver usb [ 0.075890] pps_core: LinuxPPS API ver. 1 registered [ 0.075898] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.075924] PTP clock support registered [ 0.078770] clocksource: Switched to clocksource arch_sys_counter [ 0.089652] NET: Registered PF_INET protocol family [ 0.089896] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.092299] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.092343] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.092366] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.092435] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.092588] TCP: Hash tables configured (established 4096 bind 4096) [ 0.093225] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.093620] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.093662] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.094399] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.094456] PCI: CLS 0 bytes, default 64 [ 0.096259] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.098410] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.098426] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.422532] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.427710] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.427864] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.427969] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.428093] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.428532] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.429962] qcom-pcie 40000000.pcie: host bridge /soc/pcie@40000000 ranges: [ 0.430035] qcom-pcie 40000000.pcie: IO 0x0040200000..0x00402fffff -> 0x0000000000 [ 0.430077] qcom-pcie 40000000.pcie: MEM 0x0040300000..0x0040ffffff -> 0x0040300000 [ 0.433010] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.433129] msm_serial 78af000.serial: uartclk = 1843200 [ 0.433662] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 31, base_baud = 115200) is a MSM [ 0.433719] msm_serial: console setup on port #0 [ 0.433799] printk: legacy console [ttyMSM0] enabled [ 0.580607] qcom-pcie 40000000.pcie: iATU: unroll F, 32 ob, 8 ib, align 4K, limit 4G [ 0.600353] msm_serial: driver initialized [ 0.607227] qcom-pcie 40000000.pcie: Invalid eDMA IRQs found [ 0.622346] loop: module loaded [ 0.728774] qcom-pcie 40000000.pcie: PCIe Gen.1 x1 link up [ 0.778528] i2c_dev: i2c /dev entries driver [ 0.782487] qcom-pcie 40000000.pcie: PCI host bridge to bus 0000:00 [ 0.787348] i2c_qup 78b7000.i2c: using default clock-frequency 100000 [ 0.801434] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.137681] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] [ 1.143079] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] [ 1.149312] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400 PCIe Root Port [ 1.156181] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x00000fff] [ 1.163397] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.169288] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.174482] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.180751] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref] [ 1.187553] pci 0000:00:00.0: PME# supported from D0 D3hot [ 1.197075] PCI: bus0: Fast back to back transfers disabled [ 1.200991] pci 0000:01:00.0: [168c:0056] type 00 class 0x028000 PCIe Endpoint [ 1.206231] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x001fffff 64bit] [ 1.214259] pci 0000:01:00.0: PME# supported from D0 D3hot [ 1.220731] PCI: bus1: Fast back to back transfers disabled [ 1.225326] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff]: assigned [ 1.230760] pci 0000:00:00.0: BAR 0 [mem 0x40300000-0x40300fff]: assigned [ 1.238377] pci 0000:01:00.0: BAR 0 [mem 0x40400000-0x405fffff 64bit]: assigned [ 1.245228] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.252277] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] [ 1.257472] pci_bus 0000:00: resource 4 [io 0x0000-0xfffff] [ 1.264422] pci_bus 0000:00: resource 5 [mem 0x40300000-0x40ffffff] [ 1.270152] pci_bus 0000:01: resource 1 [mem 0x40400000-0x405fffff] [ 1.280522] pcieport 0000:00:00.0: AER: enabled with IRQ 59 [ 1.288077] sdhci: Secure Digital Host Controller Interface driver [ 1.288127] sdhci: Copyright(c) Pierre Ossman [ 1.294278] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.299390] sdhci_msm 7824900.mmc: Got CD GPIO [ 1.302821] NET: Registered PF_INET6 protocol family [ 1.311445] Segment Routing with IPv6 [ 1.313828] In-situ OAM (IOAM) with IPv6 [ 1.317389] NET: Registered PF_PACKET protocol family [ 1.321374] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.326657] 8021q: 802.1Q VLAN Support v1.8 [ 1.339278] mmc0: SDHCI controller on 7824900.mmc [7824900.mmc] using ADMA 64-bit [ 1.343412] Registering SWP/SWPB emulation handler [ 1.378607] qca8k-ipq4019 c000000.switch: configuring for fixed/internal link mode [ 1.379049] qca8k-ipq4019 c000000.switch: Link is Up - 1Gbps/Full - flow control rx/tx [ 1.395427] mmc0: new HS200 MMC card at address 0001 [ 1.396600] mmcblk0: mmc0:0001 M62704 3.53 GiB [ 1.400442] Overlapping partitions are used in command line partitions. [ 1.400458] Don't use filesystems on overlapping partitions: [ 1.403731] kernel[9192448,3932160] overlaps with firmware[9454592,36175872]. [ 1.410287] rootfs[13124608,32243712] overlaps with firmware[9454592,36175872]. [ 1.416150] mmcblk0: p1(0:SBL1) p2(0:BOOTCONFIG) p3(0:QSEE) p4(0:QSEE_ALT) p5(0:CDT) p6(0:CDT_ALT) p7(0:DDRPARAMS) p8(0:APPSBLENV) p9(0:APPSBL) p10(0:APPSBL_ALT) p11(0:ART) p12(ARTMTD) p13(language) p14(config) p15(pot) p16(traffic_meter) p17(pot_bak) p18(traffic_meter.bak) p19(kernel) p20(rootfs) p21(firmware) p22(mtdoops) p23(reserved) p24(unallocated) [ 1.442755] mmcblk0boot0: mmc0:0001 M62704 2.00 MiB [ 1.463059] mmcblk0boot1: mmc0:0001 M62704 2.00 MiB [ 1.467239] mmcblk0rpmb: mmc0:0001 M62704 512 KiB, chardev (246:0) [ 1.570464] qca8k-ipq4019 c000000.switch wan (uninitialized): PHY [90000.mdio-1:00] driver [Qualcomm QCA8075] (irq=POLL) [ 1.639581] qca8k-ipq4019 c000000.switch lan1 (uninitialized): PHY [90000.mdio-1:01] driver [Qualcomm QCA8075] (irq=POLL) [ 1.709487] qca8k-ipq4019 c000000.switch lan2 (uninitialized): PHY [90000.mdio-1:02] driver [Qualcomm QCA8075] (irq=POLL) [ 1.779524] qca8k-ipq4019 c000000.switch lan3 (uninitialized): PHY [90000.mdio-1:03] driver [Qualcomm QCA8075] (irq=POLL) [ 1.780720] ipqess-edma c080000.ethernet eth0: entered promiscuous mode [ 1.789641] DSA: tree 0 setup \FF[ 1.804403] VFS: Mounted root (squashfs filesystem) readonly on device 259:12. [ 1.806431] Freeing unused kernel image (initmem) memory: 1024K [ 1.810857] Run /sbin/init as init process [ 2.163284] init: Console is alive [ 2.163657] init: - watchdog - [ 2.942735] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.020835] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 3.046593] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.055610] init: - preinit - [ 7.618786] random: crng init done Cannot parse config file '/etc/fw_env.config': No such file or directory Failed to find NVMEM device [ 8.341932] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode [ 8.342723] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode [ 8.348855] qca8k-ipq4019 c000000.switch: PSGMII calibration! [ 8.356566] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.722362] loop0: detected capacity change from 0 to 62976 [ 13.768792] loop0: detected capacity change from 62976 to 51840 [ 13.953245] EXT4-fs (loop0): recovery complete [ 13.954822] EXT4-fs (loop0): mounted filesystem 8275d90a-b1ee-40a3-975b-eaa3db1e0e94 r/w with ordered data mode. Quota mode: disabled. [ 13.957820] mount_root: overlay filesystem has not been fully initialized yet [ 13.980420] mount_root: switching to ext4 overlay [ 13.986860] urandom-seed: Seed file not found (/etc/urandom.seed) - generating board file - [ 14.597433] procd: - early - [ 14.597675] procd: - watchdog - [ 15.198636] procd: - watchdog - [ 15.199773] procd: - ubus - [ 15.295645] procd: - init - Please press Enter to activate this console. [ 16.068445] kmodloader: loading kernel modules from /etc/modules.d/* [ 16.124597] Loading modules backported from Linux version v6.18.26-0-g1fe060681 [ 16.124661] Backport generated by backports.git 6ecbb44 [ 16.343606] PPP generic driver version 2.4.2 [ 16.344911] NET: Registered PF_PPPOX protocol family [ 16.372844] ath10k 6.15 driver, optimized for CT firmware, probing pci device: 0x56. [ 16.373979] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 16.380515] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 16.650416] urngd: v1.0.2 started. [ 17.434331] ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000 [ 17.434408] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 17.446851] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fW-14-fcb240f04 api 5 features mfp,peer-flow-ctrl,peer-fixed-rate,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 d6fa6b4b [ 17.747754] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:24 crc32 81733437 [ 19.463340] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 19.463416] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 19.516691] ath10k_pci 0000:01:00.0: wmi print 'ChipType 1204 ChipTypeID 0 BoardID 10 P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 19.517603] ath10k_pci 0000:01:00.0: wmi print 'free: 114556 iram: 19860 sram: 31156' [ 19.712800] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 21.004810] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 21.004892] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 21.016778] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-14-fcb240f0 api 5 features mfp,peer-flow-ctrl,peer-fixed-rate,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 0cc1593e [ 21.061524] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 4a2bfc5d [ 22.318073] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 22.318154] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 22.366004] ath10k_ahb a000000.wifi: wmi print 'ChipType 1100 ChipTypeID 30 BoardID 14 P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 22.366949] ath10k_ahb a000000.wifi: wmi print 'free: 53428 iram: 20552 sram: 37256' [ 22.517838] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 23.525623] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 23.525719] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 23.537645] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-14-fcb240f0 api 5 features mfp,peer-flow-ctrl,peer-fixed-rate,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 0cc1593e [ 23.581688] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 4a2bfc5d [ 24.839775] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 24.839850] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 24.888260] ath10k_ahb a800000.wifi: wmi print 'ChipType 1100 ChipTypeID 30 BoardID 15 P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 24.889201] ath10k_ahb a800000.wifi: wmi print 'free: 53428 iram: 20552 sram: 37256' [ 25.030208] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 25.151939] kmodloader: done loading kernel modules from /etc/modules.d/* [ 39.054167] ipqess-edma c080000.ethernet eth0: Link is Down [ 39.060590] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode [ 39.060920] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 39.074044] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode [ 39.078028] br-lan: port 1(lan1) entered blocking state [ 39.083540] br-lan: port 1(lan1) entered disabled state [ 39.088689] qca8k-ipq4019 c000000.switch lan1: entered allmulticast mode [ 39.093967] ipqess-edma c080000.ethernet eth0: entered allmulticast mode [ 39.101358] qca8k-ipq4019 c000000.switch lan1: entered promiscuous mode [ 39.137530] qca8k-ipq4019 c000000.switch lan2: configuring for phy/psgmii link mode [ 39.139732] br-lan: port 2(lan2) entered blocking state [ 39.144058] br-lan: port 2(lan2) entered disabled state [ 39.149462] qca8k-ipq4019 c000000.switch lan2: entered allmulticast mode [ 39.155226] qca8k-ipq4019 c000000.switch lan2: entered promiscuous mode [ 39.173430] qca8k-ipq4019 c000000.switch lan3: configuring for phy/psgmii link mode [ 39.175689] br-lan: port 3(lan3) entered blocking state [ 39.180161] br-lan: port 3(lan3) entered disabled state [ 39.185243] qca8k-ipq4019 c000000.switch lan3: entered allmulticast mode [ 39.191006] qca8k-ipq4019 c000000.switch lan3: entered promiscuous mode [ 39.217068] qca8k-ipq4019 c000000.switch wan: configuring for phy/psgmii link mode [ 42.329847] qca8k-ipq4019 c000000.switch lan3: Link is Up - 1Gbps/Full - flow control rx/tx [ 42.329976] br-lan: port 3(lan3) entered blocking state [ 42.337045] br-lan: port 3(lan3) entered forwarding state

Space for additional notes, links to forum threads or other resources.

...

How to add tags

ipq40xx, IPQ4019, 16flash, emmc, 512ram, 4port, gigabitethernet, 4core, 1usb, usb2.0, serial, 2button, 12v powered, vlan, 802.11bgn, 802.11anac, ath10k-ct, u-boot

ipq40xx ipq4019 16flash emmc 512ram 4port gigabitethernet 4core 1usb usb2.0 serial 2button 12v powered vlan 802.11bgn 802.11anac ath10k-ct u-boot

Netgear RBR40

Supported Versions

Experimental Versions

Hardware Highlights

Installation

Flash Layout

OEM easy installation

OEM installation using the TFTP method

Specific values needed for tftp

Upgrading OpenWrt

LuCI Web Upgrade Process

Terminal Upgrade Process

sysupgrade

mtd

Debricking

Failsafe mode

Basic configuration

Specific Configuration

Network interfaces

Switch Ports (for VLANs)

Buttons

Hardware

Info

Photos

Opening the case

Serial

JTAG

Bootloader mods

Hardware mods

Bootlogs

OEM bootlog

OpenWrt bootlog

Notes

Tags