User Tools

Site Tools


toh:netgear:r7800

Netgear R7800

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Netgear R7800 is a dual-core 1.7 GHz AC2600 router based on IPQ8065 SoC and QCA9984 wifi.

Router has 512 MB RAM and 128 MB flash (about 80 MB free flash space after installation in 18.06 and later).

R7800

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
R7800Qualcomm Atheros IPQ80651700128NAND512Qualcomm Atheros QCA9984b/g/na/n/ac-5-2x 3.0

Installation

Master and 18.06 have now a larger kernel partition, so that kernel 4.14 and flow offloading is possible. You will need TFTP flash once to upgrade/downgrade from one group to the other group listed below. Sysupgrade works normally inside each of these groups:

  • kernel 4.4 or 4.9: 17.01, old master builds (<r7000), plus the quite earliest 18.06 builds
  • kernel 4.14: new master builds (>r7000), new 18.06 builds (rc2 and final 18.06.0)

Additionally, the both master and 18.06 use now 70 MB larger area on flash, so installing more packages is possible. That was made the default for master and 18.06 branches in June 2018. Flashing to these new “large flash” builds needs TFTP flashing, again, if you are currently running an older small 19 MB flash build (like 17.01, 18.06.0-rc1 and old master builds).

See TFTP flashing instructions below, originally from forum: R7800 TFTP installation instructions in Openwrt forum

Broken NAND Chips/Blocks

There are some models, which have broken NANDs. when flashing the Kernel, some (mostly one) blocks are skipped. As a result, the start of the root-partition (called “ubi” in this model) comes later.

Result: Bootlop of the device

What you can do is here, edit the file target/linux/ipq806x/files-x.x/arch/arm/boot/dts/qcom-ipq8065-r7800.dts and put the startAddress for “ubi” up. (&nand_controller –> nand@0 –> partitions –> ubi@1880000), currently(04.2020) at line 360 )

Edit the two numbers showing 1880000 to 18A0000. (skip 2 blocks)

Then compile the image using make.

Tuning

The default OpenWRT cpufreq tunables are not suitable for the R7800 (see https://forum.openwrt.org/t/r7800-performance/15780/29 ). To reach peak performance, paste the following lines into System > Startup > Local Startup:

echo 35 > /sys/devices/system/cpu/cpufreq/ondemand/up_threshold
echo 10 > /sys/devices/system/cpu/cpufreq/ondemand/sampling_down_factor    

Debricking

R7800 has an easy-to-use TFTP flashing recovery mode in the bootloader, similar as some other Netgear routers e.g. WNDR3700.

Prerequisites for TFTP flashing

  • A TFTP client for your computer. There are both command-line tools and GUI versions available.
    • (I use currently tftpd64 GUI tool from jounin. TFTP2 tool (from dd-wrt) used to work earlier, but for some reason it does not work with the current master images.)
  • Your computer must have an IP address from the 192.168.1.10 network, network mask 255.255.255.0, and be connected to LAN port 4 on the router. The bootloader's TFTP recovery mode defaults to 192.168.1.1. You might need to manually config the address, as some operating systems change the IP rather quickly to a link-local 196.254.x.x address if there is no DHCP server. Verify that your PC still has 192.168.1.x before trying to TFTP.
  • A new firmware to flash in. Either an original Netgear firmware or an Openwrt “factory.img” firmware. “Sysupgrade” version will not work.
  • Access to router's reset button (on the back panel)

TFTP flashing process

  1. Turn off the power, push and hold the reset button (in a hole on backside) with a pin
  2. Turn on the power and wait till power led starts flashing white (after it first flashes orange for a while)
  3. Release the reset button and tftp the factory img in binary mode. The power led will stop flashing if you succeeded in transferring the image, and the router reboots rather quickly with the new firmware.
  4. Try to ping the router (ping 192.168.1.1). If does not respond, then tftp will not work either.

Note that this TFTP flash / recovery mode is in the u-boot bootloader, so it works before the actual firmware gets started.

Uploading the firmware image with a TFTP client

$ tftp 192.168.1.1
> bin
> put openwrt-ipq806x-netgear_r7800-squashfs-factory.img

Hardware

Info

Architecture ARMv7 Processor rev 0 (v7l), arm_cortex-a15_neon-vfpv4
Vendor Netgear
Bootloader U-Boot
System-On-Chip Qualcomm Atheros IPQ8065, 1.7GHz, 2 cores
Flash-Chip NAND, Micron MT29F1G08ABBEAH4
Flash size 128 MiB
RAM 512 MiB
Wireless Qualcomm Atheros QCA9984, 2.4GHz 802.11bgn, 5GHz a/n/ac
Ethernet 10/100/1000 Mbit/s w/ vlan support
USB 2x USB 3.0, 1x eSATA
Serial Yes
JTAG ?

Flash Layout

Flash layout in 18.06.0-rc2 and later. Since 18.06 Openwrt reserves 4 MB for kernel. ubi contains rootfs (/rom) and rootfs_data (/overlay)

/proc/mtd

dev:    size   erasesize  name
mtd0: 00c80000 00020000 "qcadata"
mtd1: 00500000 00020000 "APPSBL"
mtd2: 00080000 00020000 "APPSBLENV"
mtd3: 00140000 00020000 "art"
mtd4: 00140000 00020000 "artbak"
mtd5: 00400000 00020000 "kernel"
mtd6: 06080000 00020000 "ubi"
mtd7: 00700000 00020000 "reserve"
df

Filesystem           1K-blocks      Used Available Use% Mounted on
/dev/root                 6400      6400         0 100% /rom
tmpfs                   239196      1124    238072   0% /tmp
/dev/ubi0_1              77872        92     73768   0% /overlay
overlayfs:/overlay       77872        92     73768   0% /
tmpfs                      512         0       512   0% /dev

Flash layout in Netgear Original FW:

root@R7800:~# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00c80000 00020000 "qcadata"
mtd1: 00500000 00020000 "APPSBL"
mtd2: 00080000 00020000 "APPSBLENV"
mtd3: 00140000 00020000 "ART"
mtd4: 00140000 00020000 "ART.bak"
mtd5: 00220000 00020000 "kernel"
mtd6: 01de0000 00020000 "rootfs"
mtd7: 04480000 00020000 "netgear"
mtd8: 02000000 00020000 "firmware"
mtd9: 00080000 00020000 "crashdump"
mtd10: 00380000 00020000 "language"
mtd11: 00120000 00020000 "config"
mtd12: 00120000 00020000 "pot"
mtd13: 00010000 00001000 "m25p80"
mtd14: 0001f000 0001f000 "cert"
mtd15: 0005d000 0001f000 "pot.bak"
mtd16: 001b2000 0001f000 "traffic_meter"
mtd17: 001b2000 0001f000 "traffic_meter.bak"
mtd18: 001b2000 0001f000 "dongle"
mtd19: 037b4000 0001f000 "overlay_volume"

root@R7800:~# df
Filesystem           1k-blocks      Used Available Use% Mounted on
tmpfs                      512         0       512   0% /dev
ubi0:overlay_volume      51032      6356     42032  13% /overlay
overlayfs:/overlay       51032      6356     42032  13% /

root@R7800:~# cat /proc/cpuinfo 
Processor       : ARMv7 Processor rev 0 (v7l)
processor       : 0
BogoMIPS        : 12.55

processor       : 1
BogoMIPS        : 12.55

Features        : swp half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 
CPU implementer : 0x51
CPU architecture: 7
CPU variant     : 0x2
CPU part        : 0x04d
CPU revision    : 0

Hardware        : Qualcomm Atheros AP161 reference board
Revision        : 0000
Serial          : 0000000000000000
root@R7800:~# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,relatime,size=0k)
tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
none on /proc/bus/usb type usbfs (rw,relatime)
ubi0:overlay_volume on /overlay type ubifs (rw,relatime)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)

root@R7800:~# uname -a
Linux R7800 3.4.103 #1 SMP Thu Oct 17 15:17:32 CST 2019 armv7l unknown


root@R7800:~# free
              total         used         free       shared      buffers
  Mem:       483520       190152       293368            0        10620
 Swap:            0            0            0
Total:       483520       190152       293368
                     512         0       512   0% /dev
                     
/bin/config show
   
root@R7800:~# ls -lg /etc/ath/
-rw-r--r--    1 root     root         1270 Oct 17 06:59 icm.conf
-rw-r--r--    1 root     root          144 Oct 17 15:20 non_limit_country.conf
-rw-r--r--    1 root     root          775 Oct 17 07:10 wifi.conf
-rw-r--r--    1 root     root          619 Oct 17 07:00 wrap-vma.conf

Photos

 R7800

Insert photo of back of the casing

Insert photo of backside label

 R7800

Opening the case

Detailed advice with pictures on opening the case: https://forum.openwrt.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/2?u=hnyman

Summary:

The case bottom and cover are attached to each other pretty tightly, but the case can be opened once you figure out all necessary steps:

  • The circuitboard is attached to a heatsink that is attached to the top cover. So the bottom panel (with sides) is the one to separate from the others. The heatsink is likely attached with a thermal paste or such (I never removed it).
  • There are five screws (Torx T-10) on the bottom that need to be opened. One screw is visible and four are hidden inside the rubber feet (which are attached with adhesive tape)
  • There are small clips on sides keeping the top cover tight even when the screws have been opened. These clips need to be carefully pronged open with a flat screwdriver or something.
  • Additionally, there are fangs in the vertical backpanel protecting the connectors' holes (by preventing vertical lifting). In practice the front side can be lifted up first and the backside last by pulling forward so that the connectors slide free from the backpanel holes.

 R7800 bottom panel

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

The serial header is right at the edge of the circuitboard, so it can be accessed even while the cover is attached to the circuitboard. I bended sideways the three needed pins (ground, rx, tx) that are luckily nearest to the circuitboard’s edge, so that I could easily attach the serial cable. Using the markings in my USB-ttl converter, the pin order starting from the circuitboard’s edge is: ground, rx, tx, +3.3V

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootlogs

Uboot environment

U-Boot 2012.07 [local,local] (Sep 03 2015 - 17:33:28) U-boot 2012.07 dni1 V0.4 for DNI HW ID: 29764958 NOR flash 0MB; NAND flash 128MB; RAM 512MB; 1st Radio 4x4; 2nd Radio 4x4; Cascade smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: *** Warning - bad CRC, using default environment PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial 131072 bytes read: OK MMC Device 0 not found cdp: get part failed for 0:HLOS Net: MAC1 addr:38:94:ed:b8:d6:dc athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:38:94:ed:b8:d6:db eth0, eth1 Hit any key to stop autoboot: 0 (IPQ) # printenv baudrate=115200 bootargs=console=ttyHSL1,115200n8 bootcmd=sleep 2; nmrp; if loadn_dniimg 0 0x1480000 0x44000000 && chk_dniimg 0x44000000; then bootipq2; else fw_recovery; fi bootdelay=2 eth1addr=xx:xx:xx:xx:xx:xx ethact=eth0 ethaddr=xx:xx:xx:xx:xx:xx ipaddr=192.168.1.1 loadaddr=0x42000000 machid=136c modelid=R7800 serverip=192.168.1.10 stderr=serial stdin=serial stdout=serial updateloader=ipq_nand linux && nand erase 0x01180000 0x00080000 && imgaddr=0x42000000 && source $imgaddr:script Environment size: 527/262140 bytes


OEM bootlog

U-Boot 2012.07 [local,local] (Sep 03 2015 - 17:33:28) U-boot 2012.07 dni1 V0.4 for DNI HW ID: 29764958 NOR flash 0MB; NAND flash 128MB; RAM 512MB; 1st Radio 4x4; 2nd Radio 4x4; Cascade smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: *** Warning - bad CRC, using default environment PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial 131072 bytes read: OK MMC Device 0 not found cdp: get part failed for 0:HLOS Net: MAC1 addr:38:94:ed:b8:d6:dc athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:38:94:ed:b8:d6:db eth0, eth1 Hit any key to stop autoboot: 0 Mac2 unit failed Mac1 unit failed nmrp server is stopped or failed ! Loading from device 0: nand0 (offset 0x1480000) ** check kernel image ** Verifying Checksum ... OK ** check rootfs image ** Verifying Checksum ... OK MMC Device 0 not found Loading from nand0, offset 0x1480000 Image Name: Linux-3.4.103 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2159960 Bytes = 2.1 MiB Load Address: 41508000 Entry Point: 41508000 Automatic boot of image at addr 0x44000000 ... Image Name: Linux-3.4.103 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2159960 Bytes = 2.1 MiB Load Address: 41508000 Entry Point: 41508000 Verifying Checksum ... OK Loading Kernel Image ... OK OK mtdparts variable not set, see 'help mtdparts' no partitions defined defaults: mtdids : nand0=msm_nand mtdparts: none info: "mtdparts" not set Using machid 0x136c from environment Starting kernel ... Booting Linux on physical CPU 0 Linux version 3.4.103 (li.zhang@team-3) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP Mon Dec 10 11:05:40 UTC 2018 CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache Machine: Qualcomm Atheros AP161 reference board QCA command line: console=ttyHSL1,115200n8 DNI command line: console=ttyHSL1,115200n8 ubi.mtd=netgear root=/dev/mtdblock6 msm_reserve_memory: 0x44600000, 0x200000 memory pool 3 (start 5fc00000 size 400000) initialized Memory policy: ECC disabled, Data cache writealloc smem_find(137, 80): wrong size 72 socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0, hw_plat_ver=65536 accessory_chip=0 hw_plat_subtype=0 PERCPU: Embedded 8 pages/cpu @c0d56000 s10624 r8192 d13952 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 123178 Kernel command line: console=ttyHSL1,115200n8 ubi.mtd=netgear root=/dev/mtdblock6 PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 49MB 436MB = 485MB total Memory: 482488k/488632k available, 14152k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xdf000000 - 0xff000000 ( 512 MB) lowmem : 0xc0000000 - 0xdeb00000 ( 491 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0630000 (6304 kB) .init : 0xc0700000 - 0xc0802980 (1035 kB) .data : 0xc0804000 - 0xc08a78e0 ( 655 kB) .bss : 0xc08a7904 - 0xc0952598 ( 684 kB) SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. NR_IRQS:1689 sched_clock: 32 bits at 32kHz, resolution 31240ns, wraps every 134175798ms Console: colour dummy device 80x30 Calibrating delay using timer specific routine.. 12.55 BogoMIPS (lpj=62790) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x41952a18 - 0x41952aa0 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (25.11 BogoMIPS). dummy: NET: Registered protocol family 16 AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver meminfo_init: smem ram ptable found: ver: 0 len: 5 Found 1 memory banks grouped into 8 memory regions gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio smem_find(137, 80): wrong size 72 socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0, hw_plat_ver=65536 accessory_chip=0 hw_plat_subtype=0 msm_rpm_init: RPM firmware 3.0.16777364 clk_tbl_nss_fast - loaded msm_dmov_memcpy_init: Success sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20 sps:BAM 0x12244000 is registered. sps:sps is ready. msm_pcie_setup: link initialized PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fefffff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers disabled msm_pcie_setup: link initialized PCI host bridge to bus 0000:02 pci_bus 0000:02: root bus resource [mem 0x2e000000-0x31efffff] PCI: bus2: Fast back to back transfers disabled pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus3: Fast back to back transfers disabled msm_pcie_setup: link initialization failed pci 0000:02:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] pci 0000:03:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] pci 0000:02:00.0: PCI bridge to [bus 03-03] pci 0000:02:00.0: bridge window [mem 0x2e000000-0x2e1fffff] PCI: enabling device 0000:02:00.0 (0140 -> 0143) pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] PCI: enabling device 0000:00:00.0 (0140 -> 0143) bio: create slab <bio-0> at 0 SCSI subsystem initialized spi_qsd spi_qsd.5: master is unqueued, this is deprecated spi_qsd spi_qsd.6: master is unqueued, this is deprecated usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource gp_timer NET: Registered protocol family 2 create ipmac proc IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 smd: register irq failed on wcnss_a11 smd: deregistering IRQs SMD: smd_core_platform_init() failed Partition (from dni partition table) qcadata -- Offset:0 Size:64 Partition (from dni partition table) APPSBL -- Offset:64 Size:28 Partition (from dni partition table) APPSBLENV -- Offset:8c Size:4 Partition (from dni partition table) ART -- Offset:90 Size:a Partition (from dni partition table) ART.bak -- Offset:9a Size:a Partition (from dni partition table) kernel -- Offset:a4 Size:11 Partition (from dni partition table) rootfs -- Offset:b5 Size:ef Partition (from dni partition table) netgear -- Offset:1a4 Size:224 Partition (from dni partition table) firmware -- Offset:a4 Size:100 Partition (from dni partition table) crashdump -- Offset:3c8 Size:4 Partition (from dni partition table) language -- Offset:3cc Size:1c Partition (from dni partition table) config -- Offset:3e8 Size:9 Partition (from dni partition table) pot -- Offset:3f1 Size:9 smem_find(427, 88): wrong size 96 get_bootconfig_partition 0 0 : v2 magic not found acpuclk-ipq806x acpuclk-ipq806x: SPEED BIN: 0 acpuclk-ipq806x acpuclk-ipq806x: ACPU PVS: 4 acpuclk-ipq806x acpuclk-ipq806x: CPU0: 6 frequencies supported acpuclk-ipq806x acpuclk-ipq806x: CPU1: 6 frequencies supported msm_rpm_log_probe: OK squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 942 Asymmetric key parser 'x509' registered io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled msm_serial_hs: probe of msm_serial_hs.0 failed with error -2 msm_serial_hs module loaded msm_serial_hsl: detected port #1 msm_serial_hsl.1: ttyHSL1 at MMIO 0x16340000 (irq = 184) is a MSM msm_serial_hsl: console setup on port #1 console [ttyHSL1] enabled msm_serial_hsl: driver initialized ahci ahci.0: forcing PORTS_IMPL to 0x1 ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst scsi0 : ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241 msm_nand_probe: phys addr 0x1ac00000 msm_nand_probe: dmac 0x3 msm_nand_probe: allocated dma buffer at ffdfc000, dma_addr 5f658000 status: 20 nandid: 1580a1c2 maker c2 device a1 ONFI probe : Found an ONFI compliant device MX30UF1G18AC ▒ Found a supported NAND device NAND Controller ID : 0x4030 NAND Device ID : 0x1580a1c2 Buswidth : 8 Bits Density : 128 MByte Pagesize : 2048 Bytes Erasesize: 131072 Bytes Oobsize : 64 Bytes CFG0 Init : 0xa8d408c0 CFG1 Init : 0x0004745c ECCBUFCFG : 0x00000203 Creating 13 MTD partitions on "msm_nand": 0x000000000000-0x000000c80000 : "qcadata" 0x000000c80000-0x000001180000 : "APPSBL" 0x000001180000-0x000001200000 : "APPSBLENV" 0x000001200000-0x000001340000 : "ART" 0x000001340000-0x000001480000 : "ART.bak" 0x000001480000-0x0000016a0000 : "kernel" 0x0000016a0000-0x000003480000 : "rootfs" mtd: find squashfs magic at 0x16a0000 of "msm_nand" the correct location of partition "rootfs": 0x0000016a0000-0x000003480000 0x000003480000-0x000007900000 : "netgear" 0x000001480000-0x000003480000 : "firmware" 0x000007900000-0x000007980000 : "crashdump" ata1: SATA link down (SStatus 0 SControl 300) 0x000007980000-0x000007d00000 : "language" 0x000007d00000-0x000007e20000 : "config" 0x000007e20000-0x000007f40000 : "pot" m25p80 spi5.0: found pm25lv512, expected s25fl512s m25p80 spi5.0: pm25lv512 (64 Kbytes) UBI: attaching mtd7 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 119 UBI: attached mtd7 to ubi0 UBI: MTD device name: "netgear" UBI: MTD device size: 68 MiB UBI: number of good PEBs: 548 UBI: number of bad PEBs: 0 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 6 UBI: available PEBs: 33 UBI: total number of reserved PEBs: 515 UBI: number of PEBs reserved for bad PEB handling: 5 UBI: max/mean erase counter: 3/1 UBI: image sequence number: 0 UBI: background thread "ubi_bgt0d" started, PID 662 GPIO Bitbanged MDIO: probed tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> usbcore: registered new interface driver cdc_ether Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual i2c /dev entries driver cpuidle: using governor ladder cpuidle: using governor menu Netfilter messages via NETLINK v0.30. NAT Session Management application ports priority table is loaded! nf_conntrack version 0.5.0 (7538 buckets, 30152 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP: cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 Registering SWP/SWPB emulation handler clock_late_init: Removing enables held for handed-off clocks ipq_nss_get_mac_addr: MAC[0]: 38:94:ed:b8:d6:da ipq_nss_get_mac_addr: MAC[1]: 38:94:ed:b8:d6:db no pmic restart interrupt specified VFS: Mounted root (squashfs filesystem) readonly on device 31:6. Freeing init memory: 1032K UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 5, name "overlay_volume" UBIFS: file system size: 57266176 bytes (55924 KiB, 54 MiB, 451 LEBs) UBIFS: journal size: 2920448 bytes (2852 KiB, 2 MiB, 23 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 2704822 bytes (2641 KiB) board parameter in mtd3 and mtd4 partition are same and valid - init - init started: BusyBox v1.4.2 (2018-12-10 10:26:59 UTC) multi-call binary Boot up procedure is Finished!!! Please press Enter to activate this console. Loading data from /dev/mtd11 ... Done! The data center is Running ... sysinit: Generating Rules... sysinit: Done! ssdk_plat_init start Register QCA PHY driver PHY ID is 0x4dd036 qca probe f1 phy driver succeeded! qca-ssdk module init succeeded! clbr: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint client bridge loaded device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com NTFS driver 2.1.30 [Flags: R/O MODULE]. SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled PPP generic driver version 2.4.2 NET: Registered protocol family 24 ********************************************************** * Driver :NSS GMAC Driver for RTL v(3.72a) * Version :1.0 * Copyright :Copyright (c) 2013-2015 The Linux Foundation. All rights reserved. ********************************************************** Loading DNI-ENET driver L2TP core driver, V2.0 L2TP netlink interface nss_driver - fw of size 434240 bytes copied to load addr: 40000000, nss_id : 0 nss_driver - Turbo Support 1 Supported Frequencies - 110Mhz 600Mhz 800Mhz nss_driver - fw of size 189248 bytes copied to load addr: 40800000, nss_id : 1 Error - Duplicate Interface CB Registered for interface 107 Error - Duplicate Interface CB Registered for interface 110 <NSS-CRYPTO>:Register with NSS driver- Crypto bench loaded build (Dec 10 2018, 10:50:08) dni-qos module init. bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver msm_hsusb_host msm_hsusb_host: unable to find transceiver QCA multicast snooping installed successfully xt_time: kernel timezone is -0000 nf_conntrack_rtsp v0.6.21 loading nf_nat_rtsp v0.6.21 loading NET: Registered protocol family 27 PPPoL2TP kernel driver, V0.16.1 PPTP-GRE-v1.13 2007 (C) Delta Networks Inc. ip_set: protocol 6 ctnetlink v0.93: registering with nfnetlink. ipq-dwc3 ipq-dwc3.0: unable to read platform data num of dbm eps xhci-hcd xhci-hcd.0: xHCI Host Controller xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0: irq 142, io mem 0x11000000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: xHCI Host Controller usb usb1: Manufacturer: Linux 3.4.103 xhci-hcd usb usb1: SerialNumber: xhci-hcd.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd xhci-hcd.0: xHCI Host Controller xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.4.103 xhci-hcd usb usb2: SerialNumber: xhci-hcd.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected ipq-dwc3 ipq-dwc3.1: unable to read platform data num of dbm eps xhci-hcd xhci-hcd.1: xHCI Host Controller xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3 xhci-hcd xhci-hcd.1: irq 237, io mem 0x10000000 usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.4.103 xhci-hcd usb usb3: SerialNumber: xhci-hcd.1 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd xhci-hcd.1: xHCI Host Controller xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4 usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.4.103 xhci-hcd usb usb4: SerialNumber: xhci-hcd.1 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected fuse init (API version 7.18) jnl: driver (UFSD_HEAD lke_9.4.4_b3, LBD=ON) loaded at bf580000 ufsd: driver (UFSD_HEAD lke_9.4.4_b3, acl, ioctl, sd2(5), tr, car) loaded at bf58b000 NTFSJ support included Build_for__Netgear_R7500v2_k3.4.103_2015-04-10_lke_9.4.4_b3 ufsd Kernel .config hash: original 0xb55885e, current matched. <NSS-CRYPTO>:NSS Firmware initialized <NSS-CRYPTO>:probing engine - 0 <NSS-CRYPTO>:init completed for Pipe Pair[0] <NSS-CRYPTO>:init completed for Pipe Pair[1] <NSS-CRYPTO>:init completed for Pipe Pair[2] <NSS-CRYPTO>:init completed for Pipe Pair[3] <NSS-CRYPTO>:probing engine - 1 <NSS-CRYPTO>:init completed for Pipe Pair[0] <NSS-CRYPTO>:init completed for Pipe Pair[1] <NSS-CRYPTO>:init completed for Pipe Pair[2] <NSS-CRYPTO>:init completed for Pipe Pair[3] <NSS-CRYPTO>:probing engine - 2 <NSS-CRYPTO>:init completed for Pipe Pair[0] <NSS-CRYPTO>:init completed for Pipe Pair[1] <NSS-CRYPTO>:init completed for Pipe Pair[2] <NSS-CRYPTO>:init completed for Pipe Pair[3] <NSS-CRYPTO>:probing engine - 3 <NSS-CRYPTO>:init completed for Pipe Pair[0] <NSS-CRYPTO>:init completed for Pipe Pair[1] <NSS-CRYPTO>:init completed for Pipe Pair[2] <NSS-CRYPTO>:init completed for Pipe Pair[3] sysinit: mkdir: cannot create directory '/tmp/mnt': File exists sysinit: ECC failed: 0 sysinit: ECC corrected: 0 sysinit: Number of bad blocks: 0 sysinit: Number of bbt blocks: 0 sysinit: Block size 131072, page size 2048, OOB size 64 sysinit: Dumping data starting at 0x00000000 and ending at 0x00380000... sysinit: wpspin:50100811 sysinit: sn:5K449856A0821 sysinit: SN: 5K449856A0821 sysinit: lan mac: 38:94:ed:b8:d6:da sysinit: wan mac: 38:94:ed:b8:d6:db sysinit: wlan5g mac: 38:94:ed:b8:d6:dc handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 sysinit: switch init ECM init ECM init complete sysinit: net.bridge.bridge-nf-call-ip6tables = 1 sysinit: net.bridge.bridge-nf-call-iptables = 1 sysinit: net.netfilter.nf_conntrack_tcp_no_window_check = 1 sysinit: ifconfig: SIOCSIFADDR: No such device sysinit: ifconfig: SIOCSIFADDR: No such device opmode = normal bonding: bond0: Removing slave eth0. bonding: bond0: Error: cannot release eth0. bonding: bond0: Removing slave eth1. bonding: bond0: Error: cannot release eth1. device ethlan entered promiscuous mode device ethwan entered promiscuous mode sysinit: SSDK Init OK! sysinit: operate done. sysinit: SSDK Init OK! sysinit: operate done. sysinit: SSDK Init OK! sysinit: operate done. handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 sysinit: SSDK Init OK! sysinit: operate done. sysinit: SSDK Init OK! sysinit: operate done. sysinit: SSDK Init OK! sysinit: operate done. sysinit: SSDK Init OK! sysinit: operate done. sysinit: SSDK Init OK! sysinit: operate done. sysinit: killall: acld: no process killed ethlan: 1000 Mbps Full Duplex sysinit: ioctl error (SIOCDEVPRIVATE)!br0: port 1(ethlan) entered forwarding state br0: port 1(ethlan) entered forwarding state br0: port 1(ethlan) entered disabled state br0: port 1(ethlan) entered forwarding state br0: port 1(ethlan) entered forwarding state sysinit: Deleting static route ... Done! sysinit: Adding static route ... Done! check minidlna ... clear list sysinit: grep: /tmp/etc/minidlna.conf: No such file or directory [kwilt] no run, has not been updated ! sysinit: killall: funjsq_redis: no process killed sysinit: killall: funjsq_inetd: no process killed sysinit: killall: funjsq_httpd: no process killed Jan 1 00:00:17 skipd[1984]: opening db:0 path:/data/funjsq/config/redis Jan 1 00:00:17 skipd[1984]: Load count=0 maxPos=33 sysinit: connect: : No such file or directory sysinit: killall: funjsq_detect: no process killed sysinit: killall: funjsq_daemon: no process killed sysinit: killall: funjsq_httpd: no process killed handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 Saving Data... sysinit: killall: funjsq_dns: no process killed handing previous event, sleep 2 sysinit: [httpd] start_ssl running!! Done! ADDRCONF(NETDEV_UP): brwan: link is not ready device br0 entered promiscuous mode device br0 left promiscuous mode sysinit: killall: funjsq_dns: no process killed device br0 entered promiscuous mode sysinit: /bin/sh: Syntax error: word unexpected (expecting ")") sysinit: /bin/sh: Syntax error: word unexpected (expecting ")") sysinit: -------[funjsq_init]--------start----- sysinit: -------[funjsq_init]--------end----- sysinit: iptables v1.4.10: Couldn't load target `funjsq_dns':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_dns':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables: No chain/target/match by that name. sysinit: iptables: No chain/target/match by that name. sysinit: killall: funjsq_dns: no process killed handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 sysinit: awk: /tmp/wifi_update/wireless.old: No such file or directory qcawifi disable radio wifi1 sysinit: phy for wifi device wifi1 not found sysinit: wifi1(qcawifi): disable failed qcawifi disable radio wifi0 sysinit: phy for wifi device wifi0 not found sysinit: wifi0(qcawifi): disable failed qcawifi: enable radio wifi1 handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 handing previous event, sleep 2 ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_spectral: Version 2.0.0 Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved SPECTRAL module built on Dec 10 2018 10:46:21 ath_tx99: Version 2.0 Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_pci: (Atheros/multi-bss) ol_ath_pci_probe: PCI device id 0046 :0046 PCI: enabling device 0000:01:00.0 (0140 -> 0142) *********** Cascade ************* ath_pci 0000:01:00.0: ath DEBUG: sc=0xdcb9ec00 ol_ath_pci_configure : num_desired MSI set to 0 Using PCI Legacy Interrupt chip_id 0xa chip_revision 0x0 nss register id -1 offload mode enabled = 0 nss config 0 Target Type a CLOCK PLL skipped __ol_ath_attach: dev name wifi0 ol_ath_attach() BMI inited. ol_ath_attach() BMI Get Target Info. Chip id: 0xa, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_ath_attach() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined Cal location [0]: 00000000 Wifi0 NAND FLASH Select OFFSET 0x1000 qc98xx_verify_checksum: flash checksum passed: 0x3fc5 ol_transfer_bin_file 4005: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version 0 ol_transfer_bin_file 3847: downloading file 0, Download data len 8920 First OTP send param 8000 sysinit: mkdir: cannot create directory '/dev/pts': File exists sysinit: mknod: /dev/ptmx: File exists sysinit: mknod: /dev/pts/0: Operation not permitted sysinit: mknod: /dev/pts/1: Operation not permitted ethwan: 1000 Mbps Full Duplex ol_ath_download_firmware :First OTP download and Execute is good address:0x400 return param 4660 ol_ath_download_firmware:##Board Id 1 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9984/hw.1/boardData_QCA9984_CUS239_5G_v1_001.bin ol_transfer_bin_file 3847: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version 0 ol_transfer_bin_file 3847: downloading file 0, Download data len 8920 [Flash] : Ignore Module param Second otp download Param 10000 brwan: port 1(ethwan) entered forwarding state brwan: port 1(ethwan) entered forwarding state ADDRCONF(NETDEV_CHANGE): brwan: link becomes ready brwan: port 1(ethwan) entered disabled state dni-qos attached on ethwan. ethwan: 1000 Mbps Full Duplex brwan: port 1(ethwan) entered forwarding state brwan: port 1(ethwan) entered forwarding state brwan: port 1(ethwan) entered disabled state DNI-QOS: Qos is disable ethwan: 1000 Mbps Full Duplex brwan: port 1(ethwan) entered forwarding state brwan: port 1(ethwan) entered forwarding state brwan: port 1(ethwan) entered disabled state DNI-QOS: Qos is disable ethwan: 1000 Mbps Full Duplex brwan: port 1(ethwan) entered forwarding state brwan: port 1(ethwan) entered forwarding state sysinit: net.bridge.bridge-nf-call-ip6tables = 1 sysinit: net.bridge.bridge-nf-call-iptables = 1 sysinit: net.netfilter.nf_conntrack_tcp_no_window_check = 1 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version 0 ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 Swap: bytes_left to copy: fw:16; dma_page:70336 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 191808 Target address 41b608 scn=d8bc04c0 target_write_addr=41b608 seg_info=dd8d7c10 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=QCA9984/hw.1/athwlan.bin swap_filename=/lib/firmware/QCA9984/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: QCA9984/hw.1/athwlan.bin ol_transfer_bin_file 3847: downloading file 1, Download data len 361652 ol_ath_attach() Download FW done. ol_ath_attach() HT Create . ol_ath_attach() HIF Claim. ol_ath_attach() BMI Done. ol_ath_attach 6822 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 ol_ath_attach() WMI attached. wmi_handle d8cf0000 CE_recv_buf_enqueue 853 Populate last entry 512 for CE 5 CE_recv_buf_enqueue 862 CE 5 wi 511 dest_ptr 0x59463040 nbytes 0 recv_ctxt 0xd8b82780 Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> HTC Service:0x0300 ep:1 TX flow control disabled htt_peer_map_timer_init Enter pdev d7fe8000 hrtimer d7fec8b8 htt_alloc_peer_map_mem : Alloc Success : host q vaddr d7c18000 paddr 59118000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts CE_pkt_dl_len_set CE 4 Pkt download length 64 ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d7c20000 HTC Service:0x0100 ep:2 TX flow control disabled wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event Firmware_Build_Number:68 num_rf_chain:0x00000004 ht_cap_info:0x0000085b vht_cap_info:0x339b79f2 vht_supp_mcs:0x0000ffea RES CFG Support wmi_service_bitmap 9778 Sending HOST PLATFORM as 0 to TGT ol_ath_service_ready_event: tt_support: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 1440 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 177 unit_len 1440, ol_ath_alloc_host_mem_chunk req_id 1 idx 4 num_units 177 unit_len 1440, ol_ath_alloc_host_mem_chunk req_id 1 idx 5 num_units 177 unit_len 1440, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 6 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 12288 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 7 num_units 1 unit_len 12288, idx 6 req 5 num_units 0 num_unit_info 2 unit size 1876 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 8 num_units 132 unit_len 1876, ol_ath_alloc_host_mem_chunk req_id 5 idx 9 num_units 133 unit_len 1876, ol_ath_alloc_host_mem_chunk req_id 5 idx 10 num_units 133 unit_len 1876, ol_ath_alloc_host_mem_chunk req_id 5 idx 11 num_units 133 unit_len 1876, chunk 0 len 13568 requested ,ptr 0x59ca4000 chunk 1 len 54272 requested ,ptr 0x59180000 chunk 2 len 217088 requested ,ptr 0x591c0000 chunk 3 len 254880 requested ,ptr 0x59200000 chunk 4 len 254880 requested ,ptr 0x59240000 chunk 5 len 254880 requested ,ptr 0x59280000 chunk 6 len 107520 requested ,ptr 0x591a0000 chunk 7 len 12288 requested ,ptr 0x59190000 chunk 8 len 247632 requested ,ptr 0x592c0000 chunk 9 len 249508 requested ,ptr 0x59300000 chunk 10 len 249508 requested ,ptr 0x59340000 chunk 11 len 249508 requested ,ptr 0x59380000 wmi_ready_event_rx: WMI UNIFIED READY event ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 ol_ath_attach() connect HTC. bypasswmi : 0 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Add VHT80 channel: 5690 Add VHT80 channel: 5775 Skipping VHT80 channel 5825 Add VHT80_80 channels: 5210 : 5290 Add VHT80_80 channels: 5290 : 5210 Add VHT80_80 channels: 5530 : 5610 Add VHT80_80 channels: 5610 : 5530 Add VHT80_80 channels: 5210 : 5530 Add VHT80_80 channels: 5530 : 5210 Add VHT80_80 channels: 5210 : 5610 Add VHT80_80 channels: 5610 : 5210 Add VHT80_80 channels: 5210 : 5690 Add VHT80_80 channels: 5690 : 5210 Add VHT80_80 channels: 5210 : 5775 Add VHT80_80 channels: 5775 : 5210 Add VHT80_80 channels: 5290 : 5530 Add VHT80_80 channels: 5530 : 5290 Add VHT80_80 channels: 5290 : 5610 Add VHT80_80 channels: 5610 : 5290 Add VHT80_80 channels: 5290 : 5690 Add VHT80_80 channels: 5690 : 5290 Add VHT80_80 channels: 5290 : 5775 Add VHT80_80 channels: 5775 : 5290 Add VHT80_80 channels: 5530 : 5690 Add VHT80_80 channels: 5690 : 5530 Add VHT80_80 channels: 5530 : 5775 Add VHT80_80 channels: 5775 : 5530 Add VHT80_80 channels: 5610 : 5775 Add VHT80_80 channels: 5775 : 5610 Add VHT80_80 channels: 5690 : 5775 Add VHT80_80 channels: 5775 : 5690 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach:socket creation has failed SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna. ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. the 1st socket creation has failed ieee80211com_init_netlink: 3343: Wifipos Netlink socket failed ol_if_dfs_attach: called; ptr=d7769984, radar_info=da0efb80 dfs_attach: event log enabled by default ol_ath_attach() UMAC attach . ol_if_dfs_configure: FCC domain ###### FCC BIN5 ##### fcc_b5_threshold = 4, fcc_b5_mindur = 20, fcc_b5_maxdur = 105, fcc_b5_timewindow = 12, fcc_b5_rssithresh = 20, fcc_b5_rssimargin = 10 ol_ath_attach: Calling ol_if_dfs_configure BURSTING enabled by default ol_ath_attach: Set global_ic[1] ..ptr:bfa9a824 osif_wrap_attach:432 osif wrap attached osif_wrap_devt_init:393 osif wrap dev table init done Wrap Attached: Wrap_com =da18fc00 ic->ic_wrap_com=da18fc00 &wrap_com->wc_devt=da18fc00 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_pci_probe: PCI device id 0046 :0046 PCI: enabling device 0000:03:00.0 (0140 -> 0142) *********** Cascade ************* ath_pci 0000:03:00.0: ath DEBUG: sc=0xd7800c00 ol_ath_pci_configure : num_desired MSI set to 0 Using PCI Legacy Interrupt chip_id 0xa chip_revision 0x0 nss register id -1 offload mode enabled = 0 nss config 0 Target Type a CLOCK PLL skipped __ol_ath_attach: dev name wifi1 ol_ath_attach() BMI inited. ol_ath_attach() BMI Get Target Info. Chip id: 0xa, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_ath_attach() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined Cal location [1]: 00004000 wifi1 NAND FLASH Select OFFSET 0x5000 qc98xx_verify_checksum: flash checksum passed: 0x3d47 ol_transfer_bin_file 4005: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version 0 ol_transfer_bin_file 3847: downloading file 0, Download data len 8920 First OTP send param 8000 [wifi0] FWLOG: [33793] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi0] FWLOG: [33793] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi0] FWLOG: [33793] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi0] FWLOG: [33793] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) sysinit: grep: /tmp/openvpn/client/data/openvpn_client.stat: No such file or directory sysinit: killall: miniupnpd: no process killed sysinit: no 6RD parameters available, so unset 6rd related config sysinit: /etc/rc.common: /etc/rc.common: 90: detplc: not found sysinit: mount: mounting none on /proc/bus/usb failed sysinit: syslogd can't open the temp log file: /tmp/log/log-message or /var/log/messages sysinit: 248+0 records in sysinit: 248+0 records out sysinit: ca.crt sysinit: tar: ca.crt: time stamp 2019-08-17 16:37:23 is 1566059807.153423897 s in the future sysinit: cert.info sysinit: tar: cert.info: time stamp 2019-08-17 16:37:35 is 1566059819.152892813 s in the future sysinit: client.crt sysinit: tar: client.crt: time stamp 2019-08-17 16:37:35 is 1566059819.15248669 s in the future sysinit: client.key sysinit: tar: client.key: time stamp 2019-08-17 16:37:33 is 1566059817.152049327 s in the future sysinit: dh1024.pem sysinit: tar: dh1024.pem: time stamp 2019-08-17 16:37:32 is 1566059816.151643204 s in the future sysinit: server.crt sysinit: tar: server.crt: time stamp 2019-08-17 16:37:26 is 1566059810.15120584 s in the future sysinit: server.key sysinit: tar: server.key: time stamp 2019-08-17 16:37:24 is 1566059808.150799717 s in the future ol_ath_download_firmware :First OTP download and Execute is good address:0x800 return param 4660 ol_ath_download_firmware:##Board Id 2 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9984/hw.1/boardData_QCA9984_CUS260_2G_v1_002.bin ol_transfer_bin_file 3847: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version 0 ol_transfer_bin_file 3847: downloading file 0, Download data len 8920 [Flash] : Ignore Module param Second otp download Param 10000 sysinit: cp: cannot stat '/usr/config/shadow': No such file or directory Switching to Tx Mode-1 Threshold 1000 kcg 333 :GPL NetUSB up! kc 90 : run_telnetDBGDServer start kc 227 : init_DebugD end INFO1821: NetUSB 1.02.76, 00030467 : Nov 3 2015 14:05:54 INFO1823: 7423: R7800 :R7800 sysinit: Changing password for admin sysinit: New password:INFO1824: AUTH ISOC INFO1825: MOVE_HEAD emb_lp filterAudio INFO0715: 0 : tunnelID emusblp 0 INFO0715: 1 : tunnelID emusblp 1 INFO0715: 2 : tunnelID emusblp 2 INFO0715: 3 : tunnelID emusblp 3 INFO0715: 4 : tunnelID emusblp 4 INFO0715: 5 : tunnelID emusblp 5 INFO0715: 6 : tunnelID emusblp 6 sysinit: Retype password: INFO0715: 7 : tunnelID emusblp 7 sysinit: passwd: password for admin is unchanged INFO0715: 8 : tunnelID emusblp 8 INFO0715: 9 : tunnelID emusblp 9 INFO0AF8: --- checkSBusTimeoutThread start --- usbcore: registered new interface driver KC NetUSB General Driver INFO015C: init proc : PAGE_SIZE 4096 INFO1715: infomap bfb063a0 INFO1718: sleep to wait br0 to wake up INFO15D0: tcpConnector() started... : br0 sysinit: /etc/rc.common: /etc/rc.d/S62funjsq: 13: Syntax error: "}" unexpected sysinit: iptables v1.4.10: Couldn't load target `funjsq_pre_nat':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_mark':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_nat':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_forward':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_input':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_output':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: Starting Firewall... sysinit: Done! sysinit: POT is Running... sysinit: potval: The POT-(Get/Set) Demo is Running ... Enabling NSS RPS ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version 0 ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 Swap: bytes_left to copy: fw:16; dma_page:70336 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 191808 Target address 41b608 scn=d78404c0 target_write_addr=41b608 seg_info=de0b0510 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=QCA9984/hw.1/athwlan.bin swap_filename=/lib/firmware/QCA9984/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: QCA9984/hw.1/athwlan.bin sysinit: traffic_meter start : killall: ez-ipupdate: no process killed sysinit: killall: updatednsip: no process killed sysinit: killall: updatednsip: no process killed sysinit: killall: phddns: no process killed sysinit: killall: noip2: no process killed ol_transfer_bin_file 3847: downloading file 1, Download data len 361652 sysinit: sh: NETGEAR: bad number sysinit: iptables: No chain/target/match by that name. sysinit: . sysinit: $Shutting down igmpproxy: sysinit: Killed sysinit: Unknown parameter encountered: "display charset" sysinit: Ignoring unknown parameter "display charset" sysinit: ERROR: invalid DOS charset: 'dos charset' must not be UTF8, using (default value) ASCII instead. sysinit: Cannot get device feature names: No such device Saving Data... Done! sysinit: /bin/sh: cannot create /sys/class/net/wifi1/led: Directory nonexistent sysinit: wifi1 no private ioctls. sysinit: restart the daemon telnetenable for Thin client !!! clear list sysinit: ifconfig: ppp0: error fetching interface information: Device not found ol_ath_attach() Download FW done. ol_ath_attach() HT Create . ol_ath_attach() HIF Claim. ol_ath_attach() BMI Done. ol_ath_attach 6822 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 ol_ath_attach() WMI attached. wmi_handle d6750000 CE_recv_buf_enqueue 853 Populate last entry 512 for CE 5 CE_recv_buf_enqueue 862 CE 5 wi 511 dest_ptr 0x57848040 nbytes 0 recv_ctxt 0xd7ad7600 Startup Mode-0 set pdev attach (null) -1 <=== cfg max peer id 1056 ====> HTC Service:0x0300 ep:1 TX flow control disabled htt_peer_map_timer_init Enter pdev d6448000 hrtimer d644c8b8 htt_alloc_peer_map_mem : Alloc Success : host q vaddr d676e000 paddr 57c6e000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts CE_pkt_dl_len_set CE 4 Pkt download length 64 ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from d6080000 [R7800]***boot done*** HTC Service:0x0100 ep:2 TX flow control disabled wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event Firmware_Build_Number:68 num_rf_chain:0x00000004 ht_cap_info:0x0000085b vht_cap_info:0x339b79f2 vht_supp_mcs:0x0000ffea RES CFG Support wmi_service_bitmap 9778 Sending HOST PLATFORM as 0 to TGT ol_ath_service_ready_event: tt_support: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 1440 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 177 unit_len 1440, ol_ath_alloc_host_mem_chunk req_id 1 idx 4 num_units 177 unit_len 1440, ol_ath_alloc_host_mem_chunk req_id 1 idx 5 num_units 177 unit_len 1440, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 6 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 12288 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 7 num_units 1 unit_len 12288, idx 6 req 5 num_units 0 num_unit_info 2 unit size 1876 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 8 num_units 132 unit_len 1876, ol_ath_alloc_host_mem_chunk req_id 5 idx 9 num_units 133 unit_len 1876, ol_ath_alloc_host_mem_chunk req_id 5 idx 10 num_units 133 unit_len 1876, ol_ath_alloc_host_mem_chunk req_id 5 idx 11 num_units 133 unit_len 1876, chunk 0 len 13568 requested ,ptr 0x58ff8000 chunk 1 len 54272 requested ,ptr 0x575e0000 chunk 2 len 217088 requested ,ptr 0x57600000 chunk 3 len 254880 requested ,ptr 0x57640000 chunk 4 len 254880 requested ,ptr 0x57680000 chunk 5 len 254880 requested ,ptr 0x576c0000 chunk 6 len 107520 requested ,ptr 0x57700000 chunk 7 len 12288 requested ,ptr 0x5a208000 chunk 8 len 247632 requested ,ptr 0x57740000 chunk 9 len 249508 requested ,ptr 0x57780000 chunk 10 len 249508 requested ,ptr 0x577c0000 chunk 11 len 249508 requested ,ptr 0x57000000 wmi_ready_event_rx: WMI UNIFIED READY event ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 ol_ath_attach() connect HTC. bypasswmi : 0 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach:socket creation has failed SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Firmware doest not support Smart Antenna. ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. the 1st socket creation has failed ieee80211com_init_netlink: 3343: Wifipos Netlink socket failed ol_if_dfs_attach: called; ptr=d6079984, radar_info=da0efb80 dfs_attach: event log enabled by default ol_ath_attach() UMAC attach . ol_if_dfs_configure: FCC domain ###### FCC BIN5 ##### fcc_b5_threshold = 4, fcc_b5_mindur = 20, fcc_b5_maxdur = 105, fcc_b5_timewindow = 12, fcc_b5_rssithresh = 20, fcc_b5_rssimargin = 10 ol_ath_attach: Calling ol_if_dfs_configure BURSTING enabled by default ol_ath_attach: Set global_ic[2] ..ptr:bfa9a824 osif_wrap_attach:432 osif wrap attached osif_wrap_devt_init:393 osif wrap dev table init done Wrap Attached: Wrap_com =da17d600 ic->ic_wrap_com=da17d600 &wrap_com->wc_devt=da17d600 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 __sa_init_module isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 [wifi1] FWLOG: [41222] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi1] FWLOG: [41222] WAL_DBGID_TX_AC_BUFFER_SET ( set TXBF_SND_PERIOD: value 100 wmi_status 0 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi1] FWLOG: [41222] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi1] FWLOG: [41222] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) ath_ioctl: SIOC80211IFCREATE CALLED wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 38:94:ed:b8:d6:da: Setting dscp for pdev __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling TSO bit for the vap ath1 features 4000 Enabling LRO bit for the vap ath1 features 4000 VAP device ath1 created osifp: (d79e34c0) os_if: (d876c000) siwfreq Set freq vap 0 stop send + d876c000 Set freq vap 0 stop send -d876c000 Set wait done --d876c000 sysinit: Invalid command : dni_vlan_pri WARNING: Fragmentation with HT mode NOT ALLOWED!! sysinit: Error for wireless request "Set Fragmentation Threshold" (8B24) : sysinit: SET failed on device ath1 ; Invalid argument. sysinit: Interface doesn't accept private ioctl... sysinit: stafwd (8BE0): Invalid argument DES SSID SET=on DES SSID SET=NETGEAR35 sysinit: Added user admin. ieee80211_ioctl_setparam-5962, IEEE80211_PARAM_NR_SHARE_RADIO_FLAG, MAX_RADIO_CNT = 2sysinit: watchdog: /dev/watchdog: Device or resource busy su bfee 1 mu bfee 0 su bfer 0 mu bfer 1 impl bf 0 sounding dim 3 su bfee 1 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 sysinit: Interface doesn't accept private ioctl... sysinit: vhtmubfee (8BE0): Invalid argument sysinit: /etc/rc.common: /etc/rc.common: 90: cannot create /sys/fast_classifier/skip_to_bridge_ingress: Directory nonexistent device ath1 entered promiscuous mode sysinit: Unknown parameter encountered: "display charset" sysinit: Ignoring unknown parameter "display charset" sysinit: ERROR: invalid DOS charset: 'dos charset' must not be UTF8, using (default value) ASCII instead. sysinit: Added user guest. Saving Data... Done! Saving Data... Done! sysinit: Configuration file: /var/run/hostapd-ath1.conf ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 DEVICE IS DOWN ifname=ath1 DEVICE IS DOWN ifname=ath1 sysinit: ath1: Could not connect to kernel driver sysinit: Using interface ath1 with hwaddr 38:94:ed:b8:d6:da and ssid "NETGEAR35" sysinit: random: Only 18/20 bytes of strong random data available from /dev/random sysinit: random: Not enough entropy pool available for secure operations sysinit: WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects br0: port 2(ath1) entered forwarding state br0: port 2(ath1) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath1 sysinit: ath1: interface state UNINITIALIZED->ENABLED sysinit: ath1: AP-ENABLED sysinit: /sbin/wlan: eval: 15: scan_interfaces: not found sysinit: /sbin/wlan: eval: 15: setup_interface: not found sysinit: /etc/rc.common: eval: 1: cannot create /sys/devices/sys Scan in progress.. Cancelling it tem/cpu/cpufreq/ondemand/up_threshold_any_cpu_load: Directory nowmi_unified_vdev_down_send for vap 0 (d6750000) nexistent sysinit: /etc/rc.common: eval: 1: cannot create /sys/devices/system/cpu/cpufreq/ondemand/up_threshold_multi_core: Directory nonexistent sysinit: /etc/rc.common: eval: 1: cannot create /sys/devices/system/cpu/cpufreq/ondemand/optimal_freq: Directory nonexistent sysinit: /etc/rc.common: eval: 1: cannot Scan in progress.. Cancelling it create /sys/devices/system/cpu/cpufreq/ondemand/sync_freq: Direwmi_unified_vdev_down_send for vap 0 (d6750000) ctory nonexistent sysinit: DNI streamboost auto_update sysinit: streamboost: StreamBoost: Executing boot all sysinit: streamboost: Skipping qcawifi: enable radio wifi0 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080 Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 Add VHT80 channel: 5610 Add VHT80 channel: 5690 Add VHT80 channel: 5775 Skipping VHT80 channel 5825 Add VHT80_80 channels: 5210 : 5290 Add VHT80_80 channels: 5290 : 5210 Add VHT80_80 channels: 5530 : 5610 Add VHT80_80 channels: 5610 : 5530 Add VHT80_80 channels: 5210 : 5530 Add VHT80_80 channels: 5530 : 5210 Add VHT80_80 channels: 5210 : 5610 Add VHT80_80 channels: 5610 : 5210 Add VHT80_80 channels: 5210 : 5690 Add VHT80_80 channels: 5690 : 5210 Add VHT80_80 channels: 5210 : 5775 Add VHT80_80 channels: 5775 : 5210 Add VHT80_80 channels: 5290 : 5530 Add VHT80_80 channels: 5530 : 5290 Add VHT80_80 channels: 5290 : 5610 Add VHT80_80 channels: 5610 : 5290 Add VHT80_80 channels: 5290 : 5690 Add VHT80_80 channels: 5690 : 5290 Add VHT80_80 channels: 5290 : 5775 Add VHT80_80 channels: 5775 : 5290 Add VHT80_80 channels: 5530 : 5690 Add VHT80_80 channels: 5690 : 5530 Add VHT80_80 channels: 5530 : 5775 Add VHT80_80 channels: 5775 : 5530 Add VHT80_80 channels: 5610 : 5775 Add VHT80_80 channels: 5775 : 5610 Add VHT80_80 channels: 5690 : 5775 Add VHT80_80 channels: 5775 : 5690 set TXBF_SND_PERIOD: value 100 wmi_status 0 WARNING: setting the threshold value > 256 will impact multiclient performance ath_ioctl: SIOC80211IFCREATE CALLED wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 38:94:ed:b8:d6:dc: Setting dscp for pdev __ieee80211_smart_ant_init: Smart Antenna is not supported Enabling TX checksum bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling TSO bit for the vap ath0 features 4000 Enabling LRO bit for the vap ath0 features 4000 sysinit: Mon Dec 10 11:05:00 UTC 2018 VAP device ath0 created osifp: (d79e44c0) os_if: (d5cf0000) [wifi1] FWLOG: [43197] WAL_DBGID_SECURITY_ENCR_EN ( ) [wifi1] FWLOG: [43197] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) [wifi1] FWLOG: [43228] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 siwfreq Set freq vap 0 stop send + d5cf0000 Set freq vap 0 stop send -d5cf0000 [wifi1] FWLOG: [43554] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [43554] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [43595] RESMGR_OCS_GEN_PERIODIC_NOA ( Set wait done --d5cf0000 0x0 ) [wifi1] FWLOG: [43595] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) sysinit: Invalid command : dni_vlan_pri sysinit: 1+0 records in sysinit: 1+0 records out WARNING: Fragmentation with HT mode NOT ALLOWED!! sysinit: Error for wireless request "Set Fragmentation Threshold" (8B24) : sysinit: SET failed on device ath0 ; Invalid argument. sysinit: Interface doesn't accept private ioctl... sysinit: stafwd (8BE0): Invalid argument DES SSID SET=on DES SSID SET=NETGEAR35-5G ieee80211_ioctl_setparam-5962, IEEE80211_PARAM_NR_SHARE_RADIO_FLAG, MAX_RADIO_CNT = 2Saving Data... su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 1 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 1 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 1 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 1 sounding dim 3 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 1 sounding dim 3 sysinit: Interface doesn't accept private ioctl... sysinit: vhtmubfee (8BE0): Invalid argument device ath0 entered promiscuous mode Done! Switching to Tx Mode-1 Threshold 1000 sysinit: cp: cannot stat '/usr/rae.tar.gz': No such file or directory sysinit: tar: /tmp/rae.tar.gz: Cannot open: No such file or directory sysinit: tar: Error is not recoverable: exiting now sysinit: tar: Child returned status 2 sysinit: tar: Error is not recoverable: exiting now Saving Data... Done! sysinit: mkdir: cannot create directory '/tmp/router-analytics': File exists [wifi1] FWLOG: [44661] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 sysinit: Cannot connect to server , will try 60s later!!Configuration file: /var/run/hostapd-ath0.conf ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0 sysinit: ath0: Could not connect to kernel driver sysinit: Using interface ath0 with hwaddr 38:94:ed:b8:d6:dc and ssid "NETGEAR35-5G" sysinit: random: Only 14/20 bytes of strong random data available from /dev/random sysinit: random: Not enough entropy pool available for secure operations sysinit: WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects OL vap_start + wmi_unified_vdev_start_send for vap 0 (d8cf0000) OL vap_start - sysinit: killall: net6conf: no process killed ol_vdev_start_resp_ev for vap 0 (d8cf0000) ol_ath_vap_join: join operation is only for STA/IBSS mode ol_ath_wmm_update: su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 1 sounding dim 3 wmi_unified_vdev_up_send for vap 0 (d8cf0000) __ieee80211_smart_ant_init: Smart Antenna is not supported ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 [wifi0] FWLOG: [45429] WAL_DBGID_SECURITY_ENCR_EN ( ) br0: port 3(ath0) entered forwarding state br0: port 3(ath0) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath0 [wifi0] FWLOG: [45429] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) [wifi0] FWLOG: [45466] vap-0 VDEV_MGR_VDEV_START ( 0x1685, sysinit: ath0: interface state UNINITIALIZED->ENABLED sysinit0x2: ath0: AP-ENABLED , 0x0, 0x0 ) [wifi0] FWLOG: [45466] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 sysinit: /sbin/wlan: eval: 15: scan_interfaces: not found sysinit: /sbin/wlan: eval: 15: setup_interface: not found [wifi1] FWLOG: [45693] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: Sorry, rule does not exist. sysinit: ---------------------------------------- sysinit: Vendor IE info Ioctl CMD id : 29 sysinit: ID : dd sysinit: Len (OUI+ Pcapdata) in Bytes : b sysinit: OUI : 00146c sysinit: Private capibility_data : 0801010110000000 sysinit: Frame Include Mask : 18 sysinit: ---------------------------------------- sysinit: ---------------------------------------- sysinit: Vendor IE info Ioctl CMD id : 29 sysinit: ID : dd sysinit: Len (OUI+ Pcapdata) in Bytes : b sysinit: OUI : 00146c sysinit: Private capibility_data : 0801010110000000 sysinit: Frame Include Mask : 18 sysinit: ---------------------------------------- Scan in progress.. Cancelling it wmi_unified_vdev_down_send for vap 0 (d6750000) br0: port 2(ath1) entered disabled state [wifi0] FWLOG: [45842] VDEV_MGR_HP_START_TIME ( 0x0, 0x1685, 0xb3b000 ) [wifi0] FWLOG: [45842] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 ) [wifi0] FWLOG: [45842] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi0] FWLOG: [45842] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x1685, 0x0, 0x0 ) [wifi1] FWLOG: [46723] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [46749] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [46749] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable br0: port 2(ath1) entered forwarding state br0: port 2(ath1) entered forwarding state 8021q: adding VLAN 0 to HW filter on device ath1 [wifi1] FWLOG: [47816] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 sysinit: killall: proftpd: no process killed sysinit: Changing password for admin sysinit: New password: sysinit: Retype password: sysinit: Passwords don't match sysinit: passwd: password for admin is unchanged sysinit: Unknown parameter encountered: "display charset" sysinit: Ignoring unknown parameter "display charset" sysinit: ERROR: invalid DOS charset: 'dos charset' must not be UTF8, using (default value) ASCII instead. sysinit: Added user admin. sysinit: Unknown parameter encountered: "display charset" sysinit: Ignoring unknown parameter "display charset" sysinit: ERROR: invalid DOS charset: 'dos charset' must not be UTF8, using (default value) ASCII instead. sysinit: Added user guest. [wifi1] FWLOG: [48846] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [49878] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 sysinit: no process in pidfile '/var/run/forked-daapd.pid' found; none killed sysinit: AUTO FW CHECK: power cycle [wifi1] FWLOG: [50908] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1 FW checking ... sysinit: week_day == 1 [wifi1] FWLOG: [51938] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [52969] WAL channel change freq=2437, mode=1 flags=0 rx_ok=1 tx_ok=1 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable [wifi1] FWLOG: [54000] WAL channel change freq=2442, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [55030] WAL channel change freq=2447, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [56061] WAL channel change freq=2452, mode=1 flags=0 rx_ok=1 tx_ok=1 sysinit: ping: www.netgear.com: Unknown host [wifi1] FWLOG: [57092] WAL channel change freq=2457, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [58122] WAL channel change freq=2462, mode=1 flags=0 rx_ok=1 tx_ok=1 wmi_unified_vdev_down_send for vap 0 (d6750000) mlme_create_infra_bss : Overriding HT40 channel with HT20 channel OL vap_start + wmi_unified_vdev_start_send for vap 0 (d6750000) OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 [wifi1] FWLOG: [59157] RESMGR_OCS_GEN_PERIODIC_NOA ( ol_vdev_start_resp_ev for vap 0 (d6750000) ol_ath_vap_join: join operation is only for STA/IBSS mode ol_ath_wmm_update: su bfee 0 mu bfee 0 su bfer 0 mu bfer 0 impl bf 0 sounding dim 3 wmi_unified_vdev_up_send for vap 0 (d6750000) __ieee80211_smart_ant_init: Smart Antenna is not supported 0x0 ) [wifi1] FWLOG: [59157] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [59168] vap-0 VDEV_MGR_VDEV_START ( 0x98a, 0x2, 0x0, 0x0 ) [wifi1] FWLOG: [59169] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable [wifi1] FWLOG: [59625] VDEV_MGR_HP_START_TIME ( 0x0, 0x98a, 0x1130001 ) [wifi1] FWLOG: [59625] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 ) [wifi1] FWLOG: [59625] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [59625] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x98a, 0x0, 0x0 ) sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host The abbreviation of English is Eng! Passed the checksum verification! sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: Cannot connect to server , will try 60s later!!ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: pingping: sendto: Network is unreachable sysinit: : sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: Cannot connect to server , will try 60s later!!ping: www.netgear.com: Unknown host [wifi1] FWLOG: [169938] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [170251] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [170356] WAL channel change freq=2437, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [170669] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [170774] WAL channel change freq=2462, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [171088] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable [wifi1] FWLOG: [171611] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [171924] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [172029] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [172342] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [172447] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [172761] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [172866] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [173179] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [173284] WAL channel change freq=2447, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [173598] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [173702] WAL channel change freq=2452, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [174016] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [174121] WAL channel change freq=2457, mode=1 flags=0 rx_ok=1 tx_ok=1 sysinit: ath1 Scan completed : sysinit: Cell 01 - Address: 5C:6A:80:ED:4B:AD sysinit: ESSID:"MiCasa" sysinit: Mode:Master sysinit: Frequency:2.412 GHz (Channel 1) sysinit: Quality=86/94 Signal level=-64 dBm Noise level=-95 dBm sysinit: Encryption key:on sysinit: Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s sysinit: 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s sysinit: 12 Mb/s; 48 Mb/s sysinit: Extra:bcn_int=100 sysinit: IE: IEEE 802.11i/WPA2 Version 1 sysinit: Group Cipher : CCMP sysinit: Pairwise Ciphers (1) : CCMP sysinit: Authentication Suites (1) : PSK sysinit: Extra:wme_ie=dd070050f202000104 sysinit: Extra:phy_mode=IEEE80211_MODE_11NG_HT20 sysinit: Cell 02 - Address: 5E:AD:80:ED:4B:AF sysinit: ESSID:"MGMT" sysinit: Mode:Master sysinit: Frequency:2.412 GHz (Channel 1) sysinit: Quality=86/94 Signal level=-64 dBm Noise level=-95 dBm sysinit: Encryption key:on sysinit: Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s sysinit: 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s sysinit: 12 Mb/s; 48 Mb/s sysinit: Extra:bcn_int=100 sysinit: IE: IEEE 802.11i/WPA2 Version 1 sysinit: Group Cipher : CCMP sysinit: Pairwise Ciphers (1) : CCMP sysinit: Authentication Suites (1) : PSK sysinit: Extra:wme_ie=dd070050f202000104 sysinit: Extra:phy_mode=IEEE80211_MODE_11NG_HT20 sysinit: Cell 03 - Address: 70:5A:0F:E0:65:C3 sysinit: ESSID:"DIRECT-C2-HP ENVY 7640 series" sysinit: Mode:Master sysinit: Frequency:2.437 GHz (Channel 6) sysinit: Quality=89/94 Signal level=-60 dBm Noise level=-95 dBm sysinit: Encryption key:on sysinit: Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s sysinit: 36 Mb/s; 48 Mb/s; 54 Mb/s sysinit: Extra:bcn_int=100 sysinit: IE: IEEE 802.11i/WPA2 Version 1 sysinit: Group Cipher : CCMP sysinit: Pairwise Ciphers (1) : CCMP sysinit: Authentication Suites (1) : PSK sysinit: Extra:wme_ie=dd180050f2020101880003640[wifi0] 00027a4000041435e0061322f00 sysinit: ExtrFWLOG: [174657] WAL channel change freq=5260, mode=0 flags=0 rx_ok=1 tx_ok=1 a:phy_mode=IEEE80211_MODE_11NG_HT20 sysinit: IE: WPA Version 18960 sysinit: Group Cipher : Proprietary sysinit: Pairwise Ciphers (68) : Cell 04 - Address: 5E:AD:80:ED:4B:AE sysinit: ESSID:"GuestWifi" sysinit: Mode:Master sysinit: Frequency:2.412 GHz (Channel 1) sysinit: Quality=87/94 Signal level=-63 dBm Noise level=-95 dBm sysinit: Encryption key:off sysinit: Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s sysinit: 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s sysinit: 12 Mb/s; 48 Mb/s sysinit: Extra:bcn_int=100 sysinit: Extra:wme_ie=dd070050f202000104 sysinit: Extra:phy_mode=IEEE80211_MODE_11NG_HT20 sysinit: ping: www.netgear.com: Unknown host [wifi1] FWLOG: [174434] WAL channel change freq=2442, mode=5 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [174970] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [175075] WAL channel change freq=5280, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [175389] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [175493] WAL channel change freq=5300, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [175807] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [175912] WAL channel change freq=5320, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [176225] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [176330] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [176643] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [176748] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_ok=1 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable [wifi0] FWLOG: [177062] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [177166] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [177480] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [177585] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [177898] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [178003] WAL channel change freq=5745, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [178187] WAL_DBGID_DEV_RESET ( 0xc01d, 0x494 ) [wifi0] FWLOG: [178231] WAL_DBGID_DEV_RX_TIMEOUT ( 0x1d1e, 0x2b80a, 0x2b1fa, 0x1 ) [wifi0] FWLOG: [178321] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [178844] WAL channel change freq=5785, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [179157] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [179262] WAL channel change freq=5805, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [179576] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [179680] WAL channel change freq=5825, mode=0 flags=0 rx_ok=1 tx_ok=1 sysinit: ping: www.netgear.com: Unknown host [wifi0] FWLOG: [179994] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [180099] WAL channel change freq=5500, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [180412] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [180517] WAL channel change freq=5520, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [180830] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [180935] WAL channel change freq=5540, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [181249] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [181354] WAL channel change freq=5560, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [181667] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [181772] WAL channel change freq=5580, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [182085] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [182190] WAL channel change freq=5600, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [182504] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [182518] WAL_DBGID_BB_WDOG_TRIGGERED ( 0x2c8f6, 0x13000309, 0x0, 0x1 ) [wifi0] FWLOG: [182518] WAL_DBGID_BB_WDOG_TRIGGERED ( 0xc000, 0x0 ) [wifi0] FWLOG: [182875] WAL channel change freq=5620, mode=0 flags=0 rx_ok=1 tx_ok=1 sysinit: ping: sendto: Network is unreachable [wifi0] FWLOG: [183188] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [183293] sysinit: ping: sendto: Network is unreachable WAL channel change freq=5640, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [183606] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [183711] WAL channel change freq=5660, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [184030] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 sysinit: ath0 Scan completed : sysinit: Cell 01 - Address: 5E:AE:80:ED:4B:A8 sysinit: ESSID:"MGMT" sysinit: Mode:Master sysinit: Frequency:5.18 GHz (Channel 36) sysinit: Quality=92/94 Signal level=-56 dBm Noise level=-95 dBm sysinit: Encryption key:on sysinit: Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s sysinit: 36 Mb/s; 48 Mb/s; 54 Mb/s sysinit: Extra:bcn_int=100 sysinit: IE: IEEE 802.11i/WPA2 Version 1 sysinit: Group Cipher : CCMP sysinit: Pairwise Ciphers (1) : CCMP sysinit: Authentication Suites (1) : PSK sysinit: Extra:wme_ie=dd070050f202000104 sysinit: Extra:phy_mode=IEEE80211_MODE_11AC_VHT80 sysinit: [wifi0] Cell 02 - Address: 5C:6A:80:ED:4B:AE sysinit: FWLOG: [184135] ESSID:"MiCasa" sysinit: Mode:MasterWAL channel change freq=5680, mode=0 flags=0 rx_ok=1 tx_ok=1 sysinit: Frequency:5.18 GHz (Channel 36)[wifi0] sysinit: Quality=91/94 Signal level=-57FWLOG: [184448] dBm Noise level=-95 dBm sysinit: EncrypWAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 tion key:on sysinit: Bit Rates:6 Mb/s; 9 [wifi0] Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s sysinit: FWLOG: [184553] 36 Mb/s; 48 Mb/s; 54 Mb/s sysinit: WAL channel change freq=5700, mode=0 flags=0 rx_ok=1 tx_ok=1 Extra:bcn_int=100 sysinit: IE: IEEE 8[wifi0] FWLOG: [184866] WAL channel change freq=5765, mode=10 flags=0 rx_ok=1 tx_ok=1 02.11i/WPA2 Version 1 sysinit: Group Cipher : CCMP sysinit: Pairwise Ciphers (1) : CCMP sysinit: Authentication Suites (1) : PSK sysinit: Extra:wme_ie=dd070050f202000104 sysinit: Extra:phy_mode=IEEE80211_MODE_11AC_VHT80 sysinit: Cell 03 - Address: 5E:AE:80:ED:4B:AF sysinit: ESSID:"GuestWifi" sysinit: Mode:Master sysinit: Frequency:5.18 GHz (Channel 36) sysinit: Quality=91/94 Signal level=-57 dBm Noise level=-95 dBm sysinit: Encryption key:off sysinit: Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s sysinit: 36 Mb/s; 48 Mb/s; 54 Mb/s sysinit: Extra:bcn_int=100 sysinit: Extra:wme_ie=dd070050f202000104 sysinit: Extra:phy_mode=IEEE80211_MODE_11AC_VHT80 sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: mv: cannot rename '/tmp/openvpn/client/configs/providerlist.json.new': No such file or directory sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: Current RAE Download File Path is /sw-apps/router-analytics/ and Router Model: r7800 sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host [wifi1] FWLOG: [249107] WAL_DBGID_DEV_RESET ( 0xc01d, 0x3e8 ) [wifi1] FWLOG: [249146] WAL_DBGID_DEV_RX_TIMEOUT ( 0x1d1e, 0x3cd12, 0x3a33c, 0x1 ) sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: Download file https://http.fw.updates1.netgear.com/sw-apps/router-analytics/r7800/fileinfo.txt failed! sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: ping: sendtoNetwork is unreachable: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: Download file https://http.fw.updates1.netgear.com/sw-apps/router-analytics/r7800/fileinfo.txt failed! sysinit: Download file ftp://http.fw.updates1.netgear.com/sw-apps/router-analytics/r7800/fileinfo.txt failed! sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: mv: cannot rename '/tmp/openvpn/client/configs/providerlist.json.new': No such file or directory sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: Download file ftp://http.fw.updates1.netgear.com/sw-apps/router-analytics/r7800/fileinfo.txt failed! sysinit: pingping: : sendtosendto: : Network is unreachableNetwork is unreachable [wifi1] FWLOG: [483003] WAL_DBGID_DEV_RESET ( 0xc01d, 0x3eb ) [wifi1] FWLOG: [483042] WAL_DBGID_DEV_RX_TIMEOUT ( 0x1d1e, 0x75ebb, 0x721b5, 0x2 ) sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: Download file https://http.fw.updates1.netgear.com/sw-apps/router-analytics/r7800/RAE_Policy.json failed! sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host BusyBox v1.4.2 (2018-12-10 10:26:59 UTC) Built-in shell (ash) Enter 'help' for a list of built-in commands. MM NM MMMMMMM M M $MMMMM MMMMM MMMMMMMMMMM MMM MMM MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMMM MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM' MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM MMMMMM MMMMN M MMMMMMMMM MMMM MMMM MMMM M MMMMMMM M M M --------------------------------------------------------------- For those about to rock... (%C, %R) --------------------------------------------------------------- root@R7800:/# sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable root@R7800:/# pwsysinit: ping: www.netgear.com: Unknown host d / root@R7800:/# pwd / root@R7800:/# sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable [wifi1] FWLOG: [581518] WAL_DBGID_DEV_RESET ( 0xc01d, 0x41b ) [wifi1] FWLOG: [581556] WAL_DBGID_DEV_RX_TIMEOUT ( 0x1d1e, 0x8df8d, 0x8cb18, 0x3 ) sysinit: ping: www.netgear.com: Unknown host sysinit: ping: sendto: Network is unreachable sysinit: ping: sendto: Network is unreachable sysinit: ping: www.netgear.com: Unknown host current version: V1.0.0.352; new version: V1.0.0.352 sysinit: ioctl: Cannot assign requested address sysinit: LAN: 192.168.1.1/255.255.255.0 sysinit: WAN: 192.168.10.52/255.255.255.0 sysinit: WAN status: 1000M/Full sysinit: WAN status: 1000M/Full sysinit: WAN/LAN is NOT conflicting! sysinit: no 6RD parameters available, so unset 6rd related config sysinit: adding dns 192.168.10.1 sysinit: adding dns 192.168.110.10 sysinit: adding dns 8.8.8.8 sysinit: LAN: 192.168.1.1/255.255.255.0 sysinit: WAN: 192.168.10.52/255.255.255.0 sysinit: WAN status: 1000M/Full sysinit: WAN status: 1000M/Full sysinit: WAN/LAN is NOT conflicting! sysinit: ipconflict run done sysinit: deleting routers sysinit: adding router 192.168.10.1 sysinit: Flush conntrack table sysinit: WAN new IP: 192.168.10.52 sysinit: iptables v1.4.10: Couldn't load target `funjsq_pre_nat':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_mark':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_nat':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_forward':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_input':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: iptables v1.4.10: Couldn't load target `funjsq_output':File not found sysinit: Try `iptables -h' or 'iptables --help' for more information. sysinit: Starting Firewall... sysinit: Done! sysinit: Deleting static route ... Done! sysinit: killall: ripd: no process killed sysinit: Deleting static route ... Done! sysinit: Adding static route ... Done! sysinit: iptables: No chain/target/match by that name. sysinit: :) ntpst - (offset 0x00040000 bytes in POT partition) NTP Sync Timestamp record success: 17:13:51, Feb 17, 2020 sysinit: $Shutting down igmpproxy: [kwilt] start to get info from update-sever : https://http.fw.updates1.netgear.com/sw-apps/kwilt/r7800/ sysinit: start to get info from https://http.fw.updates1.netgear.com/sw-apps/ready-genie-cloud/r7800 sysinit: time zone index is : 21 sysinit: Run NTP Client with setting: pri:time-b.netgear.com sec:time-c.netgear.com Saving Data... Done! sysinit: start to download sw-apps/ready-genie-cloud/r7800/readygeniecloud-r7800new2-20191014.tar.gz sysinit: ping: www.netgear.com: Unknown host [kwilt] start to get info from update-sever : ftp://updates1.netgear.com/sw-apps/kwilt/r7800/ sysinit: install ftp://updates1.netgear.com/sw-apps/ready-genie-cloud/r7800/readygeniecloud-r7800new2-20191014.tar.gz to R/W filesystem successfully Saving Data... Done! Saving Data... sysinit: Content-type:text/html sysinit: Done! [kwilt] start to download image : https://http.fw.updates1.netgear.com/sw-apps/kwilt/r7800/kwilt-v20160203-r7800-v1.0.0.4-003.tar.gz Saving Data... Done! Saving Data... Done! Saving Data... Done! sysinit: killall: nslookup: no process killed sysinit: :) netconn - (offset 0x00041800 bytes in POT partition) set netconn result success: Yes [kwilt] install image "kwilt-v20160203-r7800-v1.0.0.4-003.tar.gz" to R/W filesystem successfully. [kwilt] run local version, since the newly installed. [kwilt] no run, dlna has not been run ! sysinit: ping: www.netgear.com: Unknown host sysinit: Download file https://http.fw.updates1.netgear.com/sw-apps/router-analytics/r7800/RAE_Policy.json successfully! device br0 left promiscuous mode sysinit: 0 packets captured sysinit: 0 packets received by filter sysinit: 0 packets dropped by kernel sysinit: killall: funjsq_dl: no process killeddevice br0 entered promiscuous mode sysinit: killall: funjsq_httpd: no process killed root@R7800:/# pwd / root@R7800:/# current version: V1.0.0.352; new version: V1.0.0.352 ls bin hardware_version proc cloud_version hipplay rom data home root default_language_version hw_id sbin dev lib sys etc mnt tmp firmware_region module_name usr firmware_time opt var firmware_version overlay www root@R7800:/# ls -la drwxr-xr-x 1 root root 752 Feb 17 17:13 . drwxr-xr-x 1 root root 752 Feb 17 17:13 .. -rw-r--r-- 1 root root 29 Jan 1 1970 .firmware_time drwxr-xr-x 2 root root 927 Dec 10 2018 bin -rw-r--r-- 1 root root 16 Feb 17 17:13 cloud_version drwxr-xr-x 1 root root 224 Feb 16 03:31 data -rw-r--r-- 1 root root 11 Dec 10 2018 default_language_version drwxr-xr-x 8 root root 4620 Jan 1 1970 dev drwxr-xr-x 1 root root 432 Feb 16 03:31 etc -rw-r--r-- 1 root root 1 Dec 10 2018 firmware_region -rw-r--r-- 1 root root 29 Dec 10 2018 firmware_time -rw-r--r-- 1 root root 10 Dec 10 2018 firmware_version -rw-r--r-- 1 root root 6 Dec 10 2018 hardware_version drwxr-xr-x 15 root root 1312 Feb 17 17:13 hipplay lrwxrwxrwx 1 root root 4 Dec 10 2018 home -> /tmp -rw-r--r-- 1 root root 35 Dec 10 2018 hw_id drwxr-xr-x 1 root root 232 Dec 10 2018 lib lrwxrwxrwx 1 root root 8 Dec 10 2018 mnt -> /tmp/mnt -rw-r--r-- 1 root root 6 Dec 10 2018 module_name drwxr-xr-x 6 root root 552 Feb 17 17:13 opt drwxr-xr-x 9 root root 752 Feb 17 17:13 overlay dr-xr-xr-x 160 root root 0 Jan 1 1970 proc drwxr-xr-x 16 root root 448 Dec 10 2018 rom drwxr-xr-x 2 root root 3 Dec 10 2018 root drwxr-xr-x 3 root root 2381 Dec 10 2018 sbin dr-xr-xr-x 15 root root 0 Jan 1 1970 sys drwxrwxrwt 25 root root 2100 Feb 17 17:14 tmp drwxr-xr-x 1 root root 224 Oct 14 14:39 usr lrwxrwxrwx 1 root root 4 Dec 10 2018 var -> /tmp drwxr-xr-x 1 root root 224 Oct 14 14:35 www root@R7800:/# cat firmware_version V1.0.2.62 root@R7800:/# cat hardware_version R7800 root@R7800:/# cat firmware_time Mon Dec 10 11:05:46 UTC 2018 root@R7800:/# cat firmware_region root@R7800:/# current version: V1.0.0.352; new version: V1.0.0.352 [wifi1] FWLOG: [716284] WAL_DBGID_DEV_RESET ( 0xc01d, 0x3ea ) [wifi1] FWLOG: [716323] WAL_DBGID_DEV_RX_TIMEOUT ( 0x1d1e, 0xaedfc, 0xae717, 0x4 ) [wifi1] FWLOG: [751307] WAL_DBGID_DEV_RESET ( 0xc01d, 0x3eb ) [wifi1] FWLOG: [751346] WAL_DBGID_DEV_RX_TIMEOUT ( 0x1d1e, 0xb76cb, 0xb3eac, 0x5 ) current version: V1.0.0.352; new version: V1.0.0.352 Original firmware looks like to have OpenWrt origin: @R7800:/# cat /etc/openwrt_version %V @R7800:/# cat /etc/openwrt_release DISTRIB_ID="%D" DISTRIB_RELEASE="%C" DISTRIB_REVISION="%R" DISTRIB_CODENAME="standard" DISTRIB_TARGET="%S" DISTRIB_DESCRIPTION="%D %N %V" @R7800:/# uname -a Linux R7800 3.4.103 #1 SMP Thu Oct 17 15:17:32 CST 2019 armv7l unknown @R7800:/# cat /proc/mtd dev: size erasesize name mtd0: 00c80000 00020000 "qcadata" mtd1: 00500000 00020000 "APPSBL" mtd2: 00080000 00020000 "APPSBLENV" mtd3: 00140000 00020000 "ART" mtd4: 00140000 00020000 "ART.bak" mtd5: 00220000 00020000 "kernel" mtd6: 01de0000 00020000 "rootfs" mtd7: 04480000 00020000 "netgear" mtd8: 02000000 00020000 "firmware" mtd9: 00080000 00020000 "crashdump" mtd10: 00380000 00020000 "language" mtd11: 00120000 00020000 "config" mtd12: 00120000 00020000 "pot" mtd13: 00010000 00001000 "m25p80" mtd14: 0001f000 0001f000 "cert" mtd15: 0005d000 0001f000 "pot.bak" mtd16: 001b2000 0001f000 "traffic_meter" mtd17: 001b2000 0001f000 "traffic_meter.bak" mtd18: 001b2000 0001f000 "dongle" mtd19: 037b4000 0001f000 "overlay_volume" @R7800:/# mount rootfs on / type rootfs (rw) /dev/root on /rom type squashfs (ro,relatime) proc on /proc type proc (rw,relatime) sysfs on /sys type sysfs (rw,relatime) tmpfs on /tmp type tmpfs (rw,nosuid,nodev,relatime,size=0k) tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755) devpts on /dev/pts type devpts (rw,relatime,mode=600) none on /proc/bus/usb type usbfs (rw,relatime) ubi0:overlay_volume on /overlay type ubifs (rw,relatime) overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay) debugfs on /sys/kernel/debug type debugfs (rw,relatime) @R7800:/# iwconfig ifb0 no wireless extensions. ethwan no wireless extensions. qca-nss-dev0 no wireless extensions. wifi0 no wireless extensions. lo no wireless extensions. br0 no wireless extensions. qca-nss-dev3 no wireless extensions. sit0 no wireless extensions. qca-nss-dev2 no wireless extensions. ath1 IEEE 802.11ng ESSID:"NETGEAR39" Mode:Master Frequency:2.427 GHz Access Point: 8C:3B:AD:B3:B3:E3 Bit Rate:800 Mb/s Tx-Power:19 dBm RTS thr:off Fragment thr:off Encryption key:C0F8-4EEB-AFB4-74F6-ACE6-74A8-3E82-8764 [2] Security mode:open Power Management:off Link Quality=0/94 Signal level=-95 dBm Noise level=-95 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pas0 no wireless extensions. brwan no wireless extensions. ifb1 no wireless extensions. qca-nss-dev1 no wireless extensions. ath0 IEEE 802.11ac ESSID:"NETGEAR39-5G" Mode:Master Frequency:5.22 GHz Access Point: 8C:3B:AD:B3:B3:E5 Bit Rate:1.7333 Gb/s Tx-Power:21 dBm RTS thr:off Fragment thr:off Encryption key:37A9-1FEC-E8B2-0CA7-5F80-2F53-04C2-5F01 [2] Security mode:open Power Management:off Link Quality=0/94 Signal level=-95 dBm Noise level=-95 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wifi1 no wireless extensions. ethlan no wireless extensions. bond0 no wireless extensions. @R7800:/# netstat -natu Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 192.168.1.1:49152 0.0.0.0:* LISTEN tcp 0 0 192.168.1.1:49153 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:3333 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:20005 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5555 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:443 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:36594 127.0.0.1:80 TIME_WAIT tcp 0 0 :::548 :::* LISTEN tcp 0 0 :::80 :::* LISTEN tcp 0 0 :::53 :::* LISTEN tcp 0 0 :::443 :::* LISTEN udp 0 0 127.0.0.1:2313 0.0.0.0:* udp 0 0 192.168.1.1:23 0.0.0.0:* udp 0 0 0.0.0.0:33319 0.0.0.0:* udp 0 0 127.0.0.1:60202 127.0.0.1:2313 ESTABLISHED udp 0 0 127.0.0.1:53548 127.0.0.1:2313 ESTABLISHED udp 0 0 0.0.0.0:53 0.0.0.0:* udp 0 0 127.0.0.1:44095 127.0.0.1:2313 ESTABLISHED udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 127.0.0.1:39494 127.0.0.1:2313 ESTABLISHED udp 0 0 127.0.0.1:55623 127.0.0.1:2313 ESTABLISHED udp 0 0 127.0.0.1:35912 127.0.0.1:2313 ESTABLISHED udp 0 0 0.0.0.0:56650 0.0.0.0:* udp 0 0 192.168.1.1:59737 0.0.0.0:* udp 0 0 0.0.0.0:1900 0.0.0.0:* udp 0 0 0.0.0.0:1900 0.0.0.0:* udp 0 0 0.0.0.0:1900 0.0.0.0:* udp 0 0 127.0.0.1:36734 127.0.0.1:53 ESTABLISHED udp 0 0 127.0.0.1:46489 127.0.0.1:2313 ESTABLISHED udp 0 0 0.0.0.0:52637 0.0.0.0:* udp 0 0 127.0.0.1:43168 127.0.0.1:2313 ESTABLISHED udp 0 0 127.0.0.1:34464 127.0.0.1:2313 ESTABLISHED udp 0 0 127.0.0.1:59045 127.0.0.1:53 ESTABLISHED udp 0 0 127.0.0.1:42194 127.0.0.1:53 ESTABLISHED udp 0 0 127.0.0.1:43748 127.0.0.1:2313 ESTABLISHED udp 0 0 0.0.0.0:5353 0.0.0.0:* udp 0 0 0.0.0.0:5353 0.0.0.0:* udp 0 0 :::53 :::* udp 0 0 :::5353 :::* ps PID Uid VmSize Stat Command 1 root 400 S init 2 root SW [kthreadd] 3 root SW [ksoftirqd/0] 4 root DW [kworker/0:0] 5 root DW [kworker/u:0] 6 root SW [migration/0] 7 root SW [migration/1] 8 root SW [kworker/1:0] 9 root SW [ksoftirqd/1] 10 root SW< [khelper] 11 root SW [kworker/u:1] 32 root SW [kworker/0:1] 111 root SW [irq/202-msmdata] 276 root SW [sync_supers] 278 root SW [bdi-default] 279 root SW< [crypto] 280 root SW< [kblockd] 285 root SW< [ata_sff] 289 root SW< [spi_qsd.5] 292 root SW [msm-spi-thread] 303 root SW [khubd] 395 root SW< [modem_notifier] 397 root SW< [smd_channel_clo] 398 root SW< [smsm_cb_wq] 423 root SW< [qmi] 452 root SW< [nmea] 454 root SW< [rpcrouter] 470 root SW [kswapd0] 515 root SW [fsnotify_mark] 544 root SW< [smux_notify_wq] 545 root SW< [smux_tx_wq] 546 root SW< [smux_rx_wq] 547 root SW< [smux_loopback_w] 563 root SW [scsi_eh_0] 566 root SW [kworker/u:2] 578 root SW [mtdblock0] 583 root SW [mtdblock1] 588 root SW [mtdblock2] 593 root SW [mtdblock3] 598 root SW [mtdblock4] 603 root SW [mtdblock5] 606 root SW [kworker/1:1] 609 root SW [mtdblock6] 614 root SW [mtdblock7] 619 root SW [mtdblock8] 624 root SW [mtdblock9] 629 root SW [mtdblock10] 634 root SW [mtdblock11] 639 root SW [mtdblock12] 649 root SW [mtdblock13] 662 root SW [ubi_bgt0d] 669 root SW [mtdblock14] 678 root SW [mtdblock15] 687 root SW [mtdblock16] 696 root SW [mtdblock17] 705 root SW [mtdblock18] 714 root SW [mtdblock19] 763 root SW< [usbnet] 783 root SW< [iewq] 784 root DW [kinteractiveup] 793 root SW< [msm-cpufreq] 797 root SW< [rq_stats] 804 root SW< [deferwq] 1284 root SW [ubifs_bgt0_5] 1315 root 252 S /bin/sh /etc/init.d/rcS S boot 1318 root 388 S logger -s -p 6 -t sysinit 1323 root 544 S /bin/ash --login 1339 root 304 S klogd 1342 root 804 S /bin/datalib 1360 root 232 S /sbin/watchdog -t 5 /dev/watchdog 1379 root SW< [xfsalloc] 1380 root SW< [xfs_mru_cache] 1381 root SW< [xfslogd] 1397 root SW< [gmac_workqueue] 1403 root SW< [nss_freq_queue] 1404 root SW< [coredump_wait] 1434 root SW< [bond0] 1573 root 540 S /sbin/hotplug2 --override --persistent --set-rules-fi 1651 root 248 S /sbin/ubusd 1680 root 660 S /usr/bin/detcable 2 1782 root DW [kworker/u:3] 1783 root SW [kworker/u:4] 1925 root SW [kworker/1:2] 1966 root 780 S udhcpd /tmp/udhcpd.conf 2492 root SW [flush-ubifs_0_5] 3507 root SW [kworker/0:2] 3529 root 260 S /usr/sbin/net-scan 3533 root 288 S lld2d br0 3554 root SW [kworker/0:3] 3769 root 160 S udhcpc -b -i brwan -h /tmp/dhcp_name.conf -r 0.0.0.0 3781 root 296 S /usr/sbin/uhttpd -h /www -r R7800 -x /cgi-bin -t 80 - 3794 root 852 S /usr/sbin/uhttpd -h /www -r R7800 -x /cgi-bin -t 80 - 3796 root 380 S inetd 3800 root 644 S acld 3801 root 212 S aclhijackdns 3810 root 624 S /usr/sbin/ntpclient 3839 root 228 S /usr/bin/hd-idle -i 1800 3874 root 448 S /bin/sh /etc/openvpn/client/ovpn_sync_configs.sh 3943 root SW [checkSBusTimeou] 3944 root SW [NU Work:6789] 3946 root SW [NU TCP] 3947 root 436 S /sbin/KC_BONJOUR 3948 root 408 S /sbin/KC_PRINT 3949 root SW [NU UDP] 3969 root 1140 S /usr/sbin/miniupnpd 4016 root 820 S /usr/sbin/dnsmasq --except-interface=lo -u root -r /t 4023 root 652 S /usr/sbin/ntgrddns -c /tmp/ntgrdns.conf 4060 root 364 S syslogd -m 0 -T GMT-0 -c 1151 4384 root SW< [ecm_nss_ipv4_wo] 4385 root SW< [ecm_nss_ipv6_wo] 4396 root 396 S crond -c /tmp/etc/crontabs -T GMT-0 4407 root 204 S potval 4408 root 448 S /bin/sh /usr/sbin/netconn.sh 4459 root 704 S /sbin/traffic_meter 4525 root 172 S /usr/sbin/telnetenable 4532 root 436 S /bin/sh /sbin/check_status.sh 4575 root 620 S /usr/sbin/dbus-daemon --system 4601 root 240 S atd 4604 root 1024 S avahi-daemon: running [R7800.local] 4751 root 724 S hostapd -P /var/run/wifi-ath1.pid -B /var/run/hostapd 4754 root 304 S hostapd_cli -i ath1 -P /var/run/hostapd_cli-ath1.pid 4975 root 816 S /usr/sbin/ra_check 4986 root 672 S hostapd -P /var/run/wifi-ath0.pid -B /var/run/hostapd 4988 root 304 S hostapd_cli -i ath0 -P /var/run/hostapd_cli-ath0.pid 5043 root 1376 S N /usr/sbin/afpd -F /etc/netatalk/afpd.conf -P /var/run 5110 root 432 S /bin/sh /usr/sbin/check_time_machine 6489 root 292 S sleep 60 6536 root 388 S /bin/sh -c curl -k -L -g -Y 1 -y 30 --connect-timeout 6537 root 1232 S curl -k -L -g -Y 1 -y 30 --connect-timeout 20 https:/ 6538 root 1228 S curl -s -k --retry 5 https://http.fw.updates1.netgear 6552 root 292 S sleep 60 6900 root 292 S sleep 3 6920 root 404 R ps @R7800:/# ls -ls /etc/ath/ 4 -rw-r--r-- 1 root root 1270 Oct 17 06:59 icm.conf 4 -rw-r--r-- 1 root root 129 Oct 17 2019 non_limit_country.conf 4 -rw-r--r-- 1 root root 775 Oct 17 07:10 wifi.conf 1 -rw-r--r-- 1 root root 619 Oct 17 07:00 wrap-vma.conf @R7800:/# /bin/config show @R7800:/# lsmod Module Size Used by Tainted: P smart_antenna 31095 0 ath_pktlog 14371 0 mtdoops 1716 0 ecm 1709955 0 NetUSB 158739 0 GPL_NetUSB 3788 1 NetUSB umac 2030333 2 smart_antenna,ath_pktlog ath_dev 308797 2 ath_pktlog,umac hst_tx99 8098 2 umac,ath_dev ath_spectral 31598 2 umac,ath_dev ath_dfs 55087 1 umac ath_rate_atheros 35591 3 ath_pktlog,umac,ath_dev ath_hal 598106 5 ath_pktlog,umac,ath_dev,hst_tx99,ath_rate_atheros adf 14205 4 umac,ath_dev,hst_tx99,ath_hal asf 6062 6 ath_pktlog,umac,ath_dev,ath_spectral,ath_dfs,ath_hal wlan_ext 1745 2 umac,ath_dfs ufsd 374066 0 jnl 25428 1 ufsd nf_nat_dnisip 4976 0 nf_conntrack_dnisip 15353 1 nf_nat_dnisip fuse 56795 0 snd_soc_core 78887 0 dwc3_ipq 12069 0 xt_mark2prio 663 0 nf_conntrack_netlink 14646 0 xt_set 7052 0 ip_set_list_set 6970 0 ip_set_hash_netport 24507 0 ip_set_hash_netiface 24630 0 ip_set_hash_net 23039 0 ip_set_hash_ipportnet 25665 0 ip_set_hash_ipportip 20946 0 ip_set_hash_ipport 20088 0 ip_set_hash_mac 9722 0 ip_set_hash_ip 19072 0 ip_set_bitmap_port 5803 0 ip_set_bitmap_ipmac 6391 0 ip_set_bitmap_ip 6503 0 ip_set 20608 13 xt_set,ip_set_list_set,ip_set_hash_netport,ip_set_hash_netiface,ip_set_hash_net,ip_set_hash_ipportnet,ip_set_hash_ipportip,ip_set_hash_ipport,ip_set_hash_map ip6t_rt 1597 0 ip6t_hbh 1251 0 ip6t_mh 745 0 ip6t_frag 909 0 ip6t_eui64 723 0 ip6t_ah 841 0 ip6table_raw 661 0 ip6_queue 3973 0 nf_conntrack_ipv6 5108 0 nf_defrag_ipv6 5015 1 nf_conntrack_ipv6 ebt_snat 851 0 ebt_dnat 751 0 ebt_arpreply 1043 0 ebt_arp 1565 0 ebt_vlan 967 0 ebt_stp 1865 0 ebt_pkttype 625 0 ebt_limit 1081 0 ebt_among 2045 0 ebt_802_3 749 0 ebtable_nat 1061 0 nf_nat_ftp 1420 0 nf_conntrack_ftp 4614 1 nf_nat_ftp ipt_urlBlock 4432 0 ipt_TRIGGER 2335 1 ipt_spiDoS 25544 0 ipt_spiadvDoS 12042 0 nf_nat_pptp 1531 0 nf_conntrack_pptp 3176 1 nf_nat_pptp pptp 5194 0 l2tp 4069 0 ip6t_CONE 1529 0 xt_RAWNAT 2893 0 ipt_dnshijack 878 1 nf_nat_dnirtsp 3319 0 nf_conntrack_dnirtsp 4076 1 nf_nat_dnirtsp nf_nat_dnih323 4774 0 nf_conntrack_dnih323 33188 1 nf_nat_dnih323 ipt_CONENAT 1212 2 ipt_NETGEAR_REJECT 5861 0 nf_nat_tftp 498 0 nf_conntrack_tftp 2378 1 nf_nat_tftp nf_nat_snmp_basic 6979 0 nf_conntrack_snmp 705 1 nf_nat_snmp_basic nf_nat_proto_gre 928 1 nf_nat_pptp nf_conntrack_proto_gre 2986 1 nf_conntrack_pptp nf_nat_amanda 662 0 nf_conntrack_amanda 1585 1 nf_nat_amanda nf_conntrack_broadcast 758 1 nf_conntrack_snmp nf_nat_irc 855 0 nf_conntrack_irc 2476 1 nf_nat_irc xt_HL 1345 0 xt_hl 879 0 xt_ecn 1365 0 ipt_ECN 1317 0 xt_CLASSIFY 601 0 xt_time 1503 0 xt_tcpmss 963 0 xt_statistic 882 0 xt_layer7 9728 0 xt_quota 818 0 xt_pkttype 628 0 xt_physdev 1361 0 xt_owner 746 0 compat_xtables 1725 1 xt_RAWNAT nf_nat_STARCRAFT 962 0 ipt_NETMAP 739 0 xt_recent 5739 0 xt_helper 865 0 xt_connbytes 1334 0 qca_mcs 42514 1 ecm xt_CT 2365 0 ehci_hcd 49800 0 dwc3 34483 1 dwc3_ipq sd_mod 25011 0 xt_LOG 9624 0 xt_comment 512 0 bonding 79569 1 ecm dni_qos 5382 0 ifb 2959 0 qca_nss_qdisc 29613 0 qca_nss_crypto_tool 8256 0 qca_nss_crypto 15148 1 qca_nss_crypto_tool qca_nss_drv 127211 4 ecm,umac,qca_nss_qdisc,qca_nss_crypto pppoe 9231 1 ecm l2tp_netlink 6273 0 l2tp_core 12639 1 l2tp_netlink dni_enet 1318 0 qca_nss_gmac 38238 3 qca_nss_drv,dni_enet pppox 1212 1 pppoe snd_pcm_oss 31975 0 snd_mixer_oss 11939 1 snd_pcm_oss snd_pcm 59304 2 snd_soc_core,snd_pcm_oss snd_timer 15259 1 snd_pcm snd_rawmidi 15011 0 snd_seq_device 4063 1 snd_rawmidi snd_hwdep 4617 0 snd_page_alloc 4429 1 snd_pcm snd 38575 8 snd_soc_core,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_rawmidi,snd_seq_device,snd_hwdep soundcore 4102 1 snd ppp_async 6230 0 ppp_generic 22235 7 ecm,pptp,l2tp,pppoe,pppox,ppp_async slhc 4339 1 ppp_generic xfs 472888 0 ntfs 84242 0 dm_crypt 12824 0 dm_mirror 11459 0 dm_region_hash 6457 1 dm_mirror dm_log 7817 2 dm_mirror,dm_region_hash dm_mod 54770 3 dm_crypt,dm_mirror,dm_log nls_iso8859_1 2931 0 nls_cp437 4463 0 crc_ccitt 980 1 ppp_async exportfs 3032 1 xfs clbr 19626 1 umac shortcut_fe_drv 7401 1 ecm regmap_spi 932 1 snd_soc_core regmap_i2c 968 1 snd_soc_core qca_ssdk 825384 0 shortcut_fe_ipv6 52242 1 shortcut_fe_drv shortcut_fe 50218 1 shortcut_fe_drv @R7800:/sys/kernel/debug# cat /proc/cpuinfo Processor : ARMv7 Processor rev 0 (v7l) processor : 0 BogoMIPS : 12.55 processor : 1 BogoMIPS : 12.55 Features : swp half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 CPU implementer : 0x51 CPU architecture: 7 CPU variant : 0x2 CPU part : 0x04d CPU revision : 0 Hardware : Qualcomm Atheros AP161 reference board Revision : 0000 Serial : 0000000000000000 @R7800:/sys/kernel/debug# free total used free shared buffers Mem: 483520 155260 328260 0 8892 Swap: 0 0 0 Total: 483520 155260 328260


OpenWrt bootlog

Bootlog after a reset, OpenWrt master r12237-d2b8ccb1c0:

U-Boot 2012.07 [local,local] (Sep 03 2015 - 17:33:28) U-boot 2012.07 dni1 V0.4 for DNI HW ID: 29764958 NOR flash 0MB; NAND flash 128MB; RAM 512MB; 1st Radio 4x4; 2nd Radio 4x4; Cascade smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: *** Warning - bad CRC, using default environment PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial 131072 bytes read: OK MMC Device 0 not found cdp: get part failed for 0:HLOS Net: MAC1 addr:38:94:ed:b8:d6:dc athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:38:94:ed:b8:d6:db eth0, eth1 Hit any key to stop autoboot: 0 Client starts...[Listening] for ADVERTISE...TTT Retry count exceeded; boot the image as usual nmrp server is stopped or failed ! Loading from device 0: nand0 (offset 0x1480000) ** check kernel image ** Verifying Checksum ... OK ** check rootfs image ** Verifying Checksum ... OK MMC Device 0 not found Loading from nand0, offset 0x1480000 Image Name: ARM OpenWrt Linux-4.19.101 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2471625 Bytes = 2.4 MiB Load Address: 42208000 Entry Point: 42208000 Automatic boot of image at addr 0x44000000 ... Image Name: ARM OpenWrt Linux-4.19.101 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2471625 Bytes = 2.4 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK mtdparts variable not set, see 'help mtdparts' no partitions defined defaults: mtdids : nand0=msm_nand mtdparts: none info: "mtdparts" not set Using machid 0x136c from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.101 (zenotec@hornet) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12237-d2b8ccb1c0)) #0 SMP Sun Feb 16 14:36:29 2020 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] random: get_random_bytes called from start_kernel+0x80/0x47c with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu s29964 r8192 d23284 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800 [ 0.000000] Kernel command line: [ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 475876K/491520K available (5252K kernel code, 180K rwdata, 1356K rodata, 1024K init, 228K bss, 15644K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (6245 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 181 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 229 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000006] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000020] Switching to timer-based delay loop, resolution 160ns [ 0.000233] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000256] pid_max: default: 32768 minimum: 301 [ 0.000431] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000451] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001365] CPU: Testing write buffer coherency: ok [ 0.002505] Setting up static identity map for 0x42300000 - 0x42300060 [ 0.002690] rcu: Hierarchical SRCU implementation. [ 0.003528] smp: Bringing up secondary CPUs ... [ 0.005450] smp: Brought up 1 node, 2 CPUs [ 0.005466] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.005477] CPU: All CPU(s) started in SVC mode. [ 0.016406] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.016569] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016600] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.016761] pinctrl core: initialized pinctrl subsystem [ 0.017900] NET: Registered protocol family 16 [ 0.018191] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.019545] cpuidle: using governor ladder [ 0.019613] cpuidle: using governor menu [ 0.043637] usbcore: registered new interface driver usbfs [ 0.043723] usbcore: registered new interface driver hub [ 0.043809] usbcore: registered new device driver usb [ 0.043882] pps_core: LinuxPPS API ver. 1 registered [ 0.043895] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.043936] PTP clock support registered [ 0.045581] clocksource: Switched to clocksource dg_timer [ 0.048876] NET: Registered protocol family 2 [ 0.049440] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.049476] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.049516] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.049569] TCP: Hash tables configured (established 4096 bind 4096) [ 0.049669] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.049702] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.049927] NET: Registered protocol family 1 [ 0.051213] No memory allocated for crashlog [ 0.051481] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.058044] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.058065] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.067403] io scheduler noop registered [ 0.067422] io scheduler deadline registered (default) [ 0.069389] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator [ 0.069519] qcom-pcie 1b500000.pci: Linked as a consumer to regulator.0 [ 0.069548] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.069667] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.069945] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges: [ 0.070004] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.070037] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.290827] qcom-pcie 1b500000.pci: Link up [ 0.290987] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.291012] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.291033] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.291048] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.295363] PCI: bus0: Fast back to back transfers disabled [ 0.301565] PCI: bus1: Fast back to back transfers disabled [ 0.301668] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.301694] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.301822] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.301848] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.302452] pcieport 0000:00:00.0: AER enabled with IRQ 36 [ 0.302964] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator [ 0.303074] qcom-pcie 1b700000.pci: Linked as a consumer to regulator.0 [ 0.303100] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.303217] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.303498] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges: [ 0.303553] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.303581] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.533122] qcom-pcie 1b700000.pci: Link up [ 0.533272] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.533292] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.533308] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.537604] PCI: bus0: Fast back to back transfers disabled [ 0.539788] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 0.543853] PCI: bus1: Fast back to back transfers disabled [ 0.543943] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.543967] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.544099] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.544120] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.544652] pcieport 0001:00:00.0: AER enabled with IRQ 38 [ 0.547220] L2 @ QSB rate. Forcing new rate. [ 0.547437] L2 @ 384000 KHz [ 0.547623] CPU0 @ 800000 KHz [ 0.547636] CPU1 @ QSB rate. Forcing new rate. [ 0.547767] CPU1 @ 384000 KHz [ 0.551513] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.553650] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.554470] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.554525] msm_serial 16340000.serial: uartclk = 7372800 [ 0.554599] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM [ 0.554645] msm_serial: console setup on port #0 [ 1.308766] console [ttyMSM0] enabled [ 1.313742] msm_serial: driver initialized [ 1.322256] loop: module loaded [ 1.324174] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xa1 [ 1.324210] nand: Macronix MX30UF1G18AC [ 1.330894] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.334463] 8 fixed-partitions partitions found on MTD device qcom_nand.0 [ 1.342077] Creating 8 MTD partitions on "qcom_nand.0": [ 1.348964] 0x000000000000-0x000000c80000 : "qcadata" [ 1.359209] random: fast init done [ 1.375314] 0x000000c80000-0x000001180000 : "APPSBL" [ 1.384355] 0x000001180000-0x000001200000 : "APPSBLENV" [ 1.386041] 0x000001200000-0x000001340000 : "art" [ 1.391243] 0x000001340000-0x000001480000 : "artbak" [ 1.396150] 0x000001480000-0x000001880000 : "kernel" [ 1.405588] 0x000001880000-0x000007900000 : "ubi" [ 1.564429] 0x000007900000-0x000008000000 : "reserve" [ 1.578043] libphy: GPIO Bitbanged MDIO: probed [ 1.599562] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0 [ 2.469701] ar8327: qca,phy-rgmii-en is not specified [ 2.470094] libphy: Fixed MDIO Bus: probed [ 2.475980] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock [ 2.478501] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.484250] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000 [ 2.491801] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported [ 2.497621] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported [ 2.505251] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2 [ 2.513237] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported [ 2.519048] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported [ 2.526422] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors [ 2.533113] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors [ 2.540728] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled [ 2.547758] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.555564] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock [ 2.562984] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.569002] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000 [ 2.576404] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported [ 2.582161] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported [ 2.589962] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2 [ 2.597865] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported [ 2.603600] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported [ 2.611048] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors [ 2.617837] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors [ 2.625300] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled [ 2.632417] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.639306] i2c /dev entries driver [ 2.650495] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 2.650711] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 2.658720] sdhci: Secure Digital Host Controller Interface driver [ 2.664973] sdhci: Copyright(c) Pierre Ossman [ 2.671315] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.679161] NET: Registered protocol family 10 [ 2.683691] Segment Routing with IPv6 [ 2.685780] NET: Registered protocol family 17 [ 2.689836] 8021q: 802.1Q VLAN Support v1.8 [ 2.693752] Registering SWP/SWPB emulation handler [ 2.725827] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364 [ 2.741775] s1a: supplied by regulator-dummy [ 2.741926] s1a: Bringing 0uV into 1050000-1050000uV [ 2.745569] s1b: supplied by regulator-dummy [ 2.750320] s1b: Bringing 0uV into 1050000-1050000uV [ 2.754737] s2a: supplied by regulator-dummy [ 2.759484] s2a: Bringing 0uV into 775000-775000uV [ 2.763933] s2b: supplied by regulator-dummy [ 2.768343] s2b: Bringing 0uV into 775000-775000uV [ 2.774871] Speed bin: 0 [ 2.777249] PVS bin: 4 [ 2.780374] cpu cpu0: Linked as a consumer to regulator.4 [ 2.782136] cpu cpu0: Dropping the link to regulator.4 [ 2.787926] cpu cpu0: Linked as a consumer to regulator.4 [ 2.794713] cpu cpu0: Linked as a consumer to regulator.2 [ 2.798694] cpu cpu1: Linked as a consumer to regulator.5 [ 2.805498] cpu cpu1: Linked as a consumer to regulator.2 [ 2.816036] UBI: auto-attach mtd6 [ 2.816053] ubi0: attaching mtd6 [ 2.925252] UBI: EOF marker found, PEBs from 25 will be erased [ 2.962523] random: crng init done [ 3.024379] ubi0: scanning is finished [ 3.052413] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 725 LEBs [ 3.052838] ubi0: attached mtd6 (name "ubi", size 96 MiB) [ 3.057900] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.063292] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.070119] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.076984] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0 [ 3.083692] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 3.090012] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1581863789 [ 3.097039] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20 [ 3.106425] ubi0: background thread "ubi_bgt0d" started, PID 63 [ 3.107037] block ubiblock0_0: created from ubi0:0(rootfs) [ 3.121201] ubiblock: device ubiblock0_0 (rootfs) set to be root file[ 3.818957] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 3.820655] Freeing unused kernel memory: 1024K [ 3.826642] Run /sbin/init as init process [ 4.518726] init: Console is alive [ 4.518861] init: - watchdog - [ 5.089248] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.129732] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.132296] SCSI subsystem initialized [ 5.140569] ahci 29000000.sata: forcing port_map 0x0 -> 0x1 [ 5.140616] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.144946] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 5.154149] scsi host0: ahci [ 5.162036] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26 [ 5.497002] ata1: SATA link down (SStatus 0 SControl 300) [ 5.502597] ehci-platform: EHCI generic platform driver [ 5.511098] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.511689] ohci-platform: OHCI generic platform driver [ 5.522104] dwc3 11000000.dwc3: Failed to get clk 'ref': -2 [ 5.577380] dwc3 10000000.dwc3: Failed to get clk 'ref': -2 [ 5.638338] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.638391] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 5.642896] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 5.650402] xhci-hcd xhci-hcd.0.auto: irq 43, io mem 0x11000000 [ 5.660563] hub 1-0:1.0: USB hub found [ 5.665579] hub 1-0:1.0: 1 port detected [ 5.669653] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.673457] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 5.678819] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 5.686436] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.693222] hub 2-0:1.0: USB hub found [ 5.701219] hub 2-0:1.0: 1 port detected [ 5.704957] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.708846] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 5.714200] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 5.721729] xhci-hcd xhci-hcd.1.auto: irq 44, io mem 0x10000000 [ 5.731568] hub 3-0:1.0: USB hub found [ 5.736980] hub 3-0:1.0: 1 port detected [ 5.740902] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.744800] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 5.750168] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 5.757768] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.764560] hub 4-0:1.0: USB hub found [ 5.772598] hub 4-0:1.0: 1 port detected [ 5.777662] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.788165] init: - preinit - [ 7.356507] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL) [ 7.357273] dwmac1000: Master AXI performs any burst length [ 7.365398] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found [ 7.370868] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 7.378924] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 7.388161] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.398102] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 8.399863] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 11.563314] UBIFS (ubi0:1): default file-system created [ 11.564339] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 149 [ 11.641756] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 11.641781] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 11.648623] UBIFS (ubi0:1): FS size: 90660864 bytes (86 MiB, 714 LEBs), journal size 4571136 bytes (4 MiB, 36 LEBs) [ 11.658532] UBIFS (ubi0:1): reserved for root: 4282136 bytes (4181 KiB) [ 11.668767] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID EED824E3-31C4-4ED8-AD98-66D7AC3E2706, small LPT model [ 11.677159] mount_root: overlay filesystem has not been fully initialized yet [ 11.687075] mount_root: switching to ubifs overlay [ 11.713958] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 11.717807] urandom-seed: Seed file not found (/etc/urandom.seed) [ 11.811936] procd: - early - [ 11.812039] procd: - watchdog - [ 12.451261] procd: - watchdog - [ 12.451901] procd: - ubus - [ 12.621932] procd: - init - Please press Enter to activate this console. [ 12.854502] urngd: v1.0.2 started. [ 12.858158] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.865066] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc [ 12.865091] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51 [ 12.879843] xt_time: kernel timezone is -0000 [ 12.904909] PPP generic driver version 2.4.2 [ 12.905748] NET: Registered protocol family 24 [ 12.921239] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46. [ 12.921661] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 12.928689] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 13.207819] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed [ 13.331008] firmware ath10k!QCA9984!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed [ 13.374721] firmware ath10k!QCA9984!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed [ 13.423584] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed [ 13.684727] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 13.684796] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 13.702522] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-013-e0e3a0aae api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 3febdfdc [ 16.031816] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734 [ 21.897876] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 21.897911] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 21.980277] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 21.981130] ath10k_pci 0000:01:00.0: wmi print 'free: 81784 iram: 13028 sram: 14440' [ 22.176800] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 22.333355] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46. [ 22.334530] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 22.341258] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 22.837521] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed [ 22.954356] firmware ath10k!QCA9984!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed [ 22.997882] firmware ath10k!QCA9984!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed [ 23.041736] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed [ 23.041922] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 23.049688] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 23.062131] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-013-e0e3a0aae api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 3febdfdc [ 25.411644] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734 [ 31.311976] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 31.312005] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 31.396561] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 31.397449] ath10k_pci 0001:01:00.0: wmi print 'free: 81784 iram: 13028 sram: 14440' [ 31.632308] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 31.782506] kmodloader: done loading kernel modules from /etc/modules.d/* [ 40.244708] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL) [ 40.245470] dwmac1000: Master AXI performs any burst length [ 40.253716] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found [ 40.259056] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 40.267152] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 40.276134] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 40.284752] br-lan: port 1(eth1.1) entered blocking state [ 40.288835] br-lan: port 1(eth1.1) entered disabled state [ 40.295463] device eth1.1 entered promiscuous mode [ 40.299688] device eth1 entered promiscuous mode [ 40.305599] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 40.314086] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL) [ 40.315945] dwmac1000: Master AXI performs any burst length [ 40.324871] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found [ 40.330379] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 40.338411] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 40.347630] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 40.358284] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready [ 41.355991] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 41.355999] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 41.364014] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 41.372957] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready [ 41.379018] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 41.385600] br-lan: port 1(eth1.1) entered blocking state [ 41.391538] br-lan: port 1(eth1.1) entered forwarding state [ 41.405204] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.31.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r12237-d2b8ccb1c0 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


Notes

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/netgear/r7800.txt · Last modified: 2020/06/03 11:34 by tcolov