NETGEAR R6800
The Netgear R6800 is an AC1900 simultaneous dual band N/AC (2.4 & 5 GHz) WiFi router with three removable external antennas. It features four Gbit LAN ports, one Gbit WAN port, dual core (quad thread) MIPS CPU, 128 MB NAND flash ROM, and 256 MB RAM.
It is based on the MT7621AT and MT7615E chips and has several clones of the same FCC ID PY316200344: Nighthawk AC2100 and AC2400, R6700v2, R6900 v2, and R7450
R6900 v2 and R7450 support was added in 22.03.00 when this device, R6700 v2, and AC2400 were already supported. Differences in clones include no USB 2.0 port and a Guest WiFi LED replacing the USB 2.0 LED.
OpenWrt support
Hardware Highlights
Installation
Installing OpenWrt
OEM easy installation
Apply factory OpenWrt image via OEM web-gui.
Debricking / back to stock firmware
Debricking of the R6800 can be done by using the tool nmrpflash tool. See details over here: https://github.com/jclehner/nmrpflash
This tool can also be used to go back to stock firmware. For Windows users, ethernet cable must be connected to a switch or nmrpflash would fail to operate.
This process only works with OEM firmware, don't try to flash OpenWrt images with nmrpflash.
Hardware
Info
Flash Layout
Netgear R6800 Flash Layout | ||||||||
---|---|---|---|---|---|---|---|---|
Layer0 | NAND flash memory chip (Macronix 3,3V 8-bit SLC) 128 MiB | |||||||
Layer1 | mtd0 u-boot 1 MiB | mtd1 PART_MAP 1 MiB | mtd2 kernel 4 MiB | mtd3 ubi 40 MiB | mtd4 ureserved0 24 MiB | mtd5 factory 2 MiB | mtd6 reserved1 56 MiB | |
mountpoint | / | /rom | ||||||
filesystem | SquashFS | OverlayFS | ||||||
Size in KiB | 1024 KiB | 1024 KiB | 4096 KiB | 40960 KiB | 24576 KiB | 2048 KiB | 57344 KiB |
Photos
Opening the case
Netgear R6800 case have five screws: four torx under leg tape (red mark on photo) and one secure torx in the middle (green). After screws removal, top case can be removed easily.
Serial
→ port.serial general information about the serial port, serial port cable, etc.
Serial connector isn't connected to CPU by default. Is required to solder two jumpers on resistors: R195, R26.
JP1 connector:
pin | function |
---|---|
1 | Vcc (~3.3V) |
2 | RX |
3 | TX |
4 | GND |
Serial connection parameters for Netgear R6800 | JP1: 57600, 8N1 |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
Board has no JTAG connector.
Bootlogs
OEM bootlog
=================================================================== MT7621 stage1 code Mar 12 2015 14:42:52 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0x8, 1/0 = 585/439 21000000 PLL2 FB_DL: 0x14, 1/0 = 550/474 51000000 PLL4 FB_DL: 0x18, 1/0 = 572/452 61000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DRAMC_DQSCTL1[0e0]=14000000 DRAMC_DQSGCTL[124]=80000000 rank 0 coarse = 16 rank 0 fine = 40 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_DDR2CTL[07c]=C287221D DRAMC_PADCTL4[0e4]=000022B3 DRAMC_DQIDLY1[210]=090C060C DRAMC_DQIDLY2[214]=040C070B DRAMC_DQIDLY3[218]=0C040A02 DRAMC_DQIDLY4[21c]=0A030C07 DRAMC_R0DELDLY[018]=00001E1F ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 10 2 11 6 11 3 11 2 0 8 10 | 2 11 7 9 3 9 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =31 DQS1 = 30 ================================================================== bit DQS0 bit DQS1 0 (1~58)29 8 (3~54)28 1 (1~53)27 9 (1~56)28 2 (1~59)30 10 (1~56)28 3 (1~56)28 11 (1~58)29 4 (1~61)31 12 (1~60)30 5 (1~53)27 13 (1~54)27 6 (1~60)30 14 (1~59)30 7 (1~58)29 15 (1~58)29 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 12 6 12 9 11 7 12 4 2 10 10 | 4 12 7 12 3 10 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff01aa DQ loop=14, cmp_err_1 = ffff01a8 DQ loop=13, cmp_err_1 = ffff01a0 DQ loop=12, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=12, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=12, finish count=2 byte:0, (DQS,DQ)=(9,8) byte:1, (DQS,DQ)=(9,8) DRAMC_DQODLY1[200]=88888888 DRAMC_DQODLY2[204]=88888888 20,data:99 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Jul 26 2016 - 00:50:05) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ff34000 Config XHCI 40M PLL Allocate 16 byte aligned buffer: 8ff7cd70 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device not found, ID: c2f1 Not Support this Device! chip_mode=00000001 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 .*** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.3.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Jul 26 2016 Time:00:50:05 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes reset PHY #Reset_MT7530 SC_DEBUG: Nand Partition Table Magic Found at 100000. .. Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. 0 0006fffa *************************************************** Sercomm Boot Version 1.0.1.0 *************************************************** Enter NMRP_main Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done ETH_STATE_ACTIVE!! NMRP_FLASH_SIZE_buffer --> 03000000. NMRP:LISTENING ### No NMRP Server found ### check upgrade flag read flag 05400000 ## Booting image at bc200000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3351447 Bytes = 3.2 MB Load Address: 81001000 Entry Point: 8100d1d0 .................................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8100d1d0) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Linux version 2.6.36 (eason@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #2 SMP Fri Jul 5 10:53:47 CST 2019 The CPU feqenuce set to 880 MHz GCMP present CPU revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 0f900000 @ 00000000 (usable) memory: 00008000 @ 0f900000 (reserved) memory: 006f8000 @ 0f908000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00010000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00010000 Detected 3 available secondary CPU(s) PERCPU: Embedded 7 pages/cpu @81af3000 s6528 r8192 d13952 u65536 pcpu-alloc: s6528 r8192 d13952 u65536 alloc=16*4096 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 console=ttyS0 PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Writing ErrCtl register=00000e60 Readback ErrCtl register=00000e60 Memory: 250592k/262112k available (5390k kernel code, 11520k reserved, 2653k data, 212k init, 0k highmem) Hierarchical RCU implementation. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Trying to install interrupt handler for IRQ24 Trying to install interrupt handler for IRQ25 Trying to install interrupt handler for IRQ22 Trying to install interrupt handler for IRQ9 Trying to install interrupt handler for IRQ10 Trying to install interrupt handler for IRQ11 Trying to install interrupt handler for IRQ12 Trying to install interrupt handler for IRQ13 Trying to install interrupt handler for IRQ14 Trying to install interrupt handler for IRQ16 Trying to install interrupt handler for IRQ17 Trying to install interrupt handler for IRQ18 Trying to install interrupt handler for IRQ19 Trying to install interrupt handler for IRQ20 Trying to install interrupt handler for IRQ21 Trying to install interrupt handler for IRQ23 Trying to install interrupt handler for IRQ26 Trying to install interrupt handler for IRQ27 Trying to install interrupt handler for IRQ28 Trying to install interrupt handler for IRQ15 Trying to install interrupt handler for IRQ8 Trying to install interrupt handler for IRQ29 Trying to install interrupt handler for IRQ30 Trying to install interrupt handler for IRQ31 console [ttyS1] enabled Calibrating delay loop... 575.48 BogoMIPS (lpj=1150976) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. launch: starting cpu2 launch: cpu2 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. launch: starting cpu3 launch: cpu3 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Brought up 4 CPUs Synchronize counters across 4 CPUs: done. NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x60200000-0x6020ffff] (PCI address [0x60200000-0x6020ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] pci 0000:00:01.0: BAR 1: set to [mem 0x60210000-0x6021ffff] (PCI address [0x60210000-0x6021ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:00:00.0: bridge window [mem pref disabled] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] pci 0000:02:00.0: BAR 0: set to [mem 0x60100000-0x601fffff 64bit] (PCI address [0x60100000-0x601fffff] pci 0000:00:01.0: PCI bridge to [bus 02-02] pci 0000:00:01.0: bridge window [io disabled] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] pci 0000:00:01.0: bridge window [mem pref disabled] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60200000 res[1]->end = 6020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60210000 res[1]->end = 6021ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60100000 res[0]->end = 601fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource Ralink Systick timer NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 128 (order: 0, 4096 bytes) UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1167360) squashfs: version 4.0 (2009/01/31) Phillip Lougher fuse init (API version 7.15) msgmni has been set to 489 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) Ralink gpio driver initialized spidrv_major = 217 spdif_mod_init: start SPDIF module Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A brd: module loaded MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 818449e0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02, 00809502] Device not found, ID: c2f1 Not Support this Device! chip_mode=00000001 Support this Device in MTK table! c2f1 NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit) [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Scanning device for bad blocks Signature matched and data read! load_fact_bbt success 1023 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Go to read Magic at 100000 page: 200 SC_DEBUG: NAND Partition Table Magic Fount at 100000. page: 201 part 0,real_offset 00000000, real_length 00100000 page: 201 part 1,real_offset 00100000, real_length 00100000 page: 201 part 2,real_offset 00200000, real_length 00400000 page: 201 part 3,real_offset 00600000, real_length 02800000 page: 201 part 4,real_offset 02e00000, real_length 00200000 page: 201 part 5,real_offset 03000000, real_length 00200000 page: 201 part 6,real_offset 03200000, real_length 00200000 page: 201 part 7,real_offset 03400000, real_length 00200000 page: 201 part 8,real_offset 03600000, real_length 00200000 page: 201 part 9,real_offset 03800000, real_length 00200000 page: 201 part 10,real_offset 03a00000, real_length 00200000 page: 201 part 11,real_offset 03c00000, real_length 00200000 page: 201 part 12,real_offset 03e00000, real_length 00200000 page: 201 part 13,real_offset 04000000, real_length 00200000 page: 201 part 14,real_offset 04200000, real_length 00200000 page: 201 part 15,real_offset 04400000, real_length 00200000 page: 201 part 16,real_offset 04600000, real_length 00200000 page: 201 part 17,real_offset 04800000, real_length 00200000 page: 201 part 18,real_offset 04a00000, real_length 00200000 page: 201 part 19,real_offset 04c00000, real_length 00200000 page: 201 part 20,real_offset 04e00000, real_length 00200000 page: 201 part 21,real_offset 05000000, real_length 00200000 page: 201 part 22,real_offset 05200000, real_length 00200000 page: 201 part 23,real_offset 05400000, real_length 00200000 page: 201 part 24,real_offset 05600000, real_length 00200000 page: 201 part 25,real_offset 05800000, real_length 00200000 page: 201 part 26,real_offset 05a00000, real_length 00200000 page: 201 part 27,real_offset 05c00000, real_length 00200000 page: 201 part 28,real_offset 05e00000, real_length 02180000 Creating 29 MTD partitions on "MT7621-NAND": 0x000000000000-0x000000100000 : "Bootloader" 0x000000100000-0x000000200000 : "SC_PART_MAP" 0x000000200000-0x000000600000 : "Kernel" 0x000000600000-0x000002e00000 : "Rootfs" 0x000002e00000-0x000003000000 : "English UI" 0x000003000000-0x000003200000 : "ML1" 0x000003200000-0x000003400000 : "ML2" 0x000003400000-0x000003600000 : "ML3" 0x000003600000-0x000003800000 : "ML4" 0x000003800000-0x000003a00000 : "ML5" 0x000003a00000-0x000003c00000 : "ML6" 0x000003c00000-0x000003e00000 : "ML7" 0x000003e00000-0x000004000000 : "ML8" 0x000004000000-0x000004200000 : "ML9" 0x000004200000-0x000004400000 : "ML10" 0x000004400000-0x000004600000 : "ML11" 0x000004600000-0x000004800000 : "Factory" 0x000004800000-0x000004a00000 : "SC Private Data" 0x000004a00000-0x000004c00000 : "POT" 0x000004c00000-0x000004e00000 : "Traffic Meter" 0x000004e00000-0x000005000000 : "SC PID" 0x000005000000-0x000005200000 : "SC Nvram" 0x000005200000-0x000005400000 : "Ralink Nvram" 0x000005400000-0x000005600000 : "Reserved Block1" 0x000005600000-0x000005800000 : "Reserved Block2" 0x000005800000-0x000005a00000 : "Reserved Block3" 0x000005a00000-0x000005c00000 : "Reserved Block4" 0x000005c00000-0x000005e00000 : "Reserved Block5" 0x000005e00000-0x000007f80000 : "Reserved Block6" [mtk_nand] probe successfully! rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288039 Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x432880e5 PROC INIT OK! PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 IMQ driver loaded successfully. Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. register mt_drv === pAd = c0182000, size = 3653048 === <-- RTMPAllocAdapterBlock, Status=0 get_wdev_by_idx: invalid idx(0) pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000! get_wdev_by_idx: invalid idx(0) RTMPInitPCIeDevice():device_id=0x7615 DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 RtmpChipOpsHook(493): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 1st iPAiLNA default bin. Use 0st /etc_ro/wlan/MT7615E_EEPROM1.bin default bin. <--mt7615_init() ChipOpsMCUHook cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8f34df88,8f34df88 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8f34df98,8f34df98 <-- RTMPAllocTxRxRingMemory, Status=0 get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) pci probe count=1 === pAd = c0602000, size = 3653048 === <-- RTMPAllocAdapterBlock, Status=0 get_wdev_by_idx: invalid idx(0) pAd->PciHif.CSRBaseAddress =0xc0500000, csr_addr=0xc0500000! get_wdev_by_idx: invalid idx(0) RTMPInitPCIeDevice():device_id=0x7615 DriverOwn()::Try to Clear FW Own... DriverOwn()::Success to clear FW Own mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 RtmpChipOpsHook(493): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 2nd ePAeLNA default bin. Use 1st /etc_ro/wlan/MT7615E_EEPROM2.bin default bin. <--mt7615_init() ChipOpsMCUHook cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8f34d208,8f34d208 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 8f34d218,8f34d218 <-- RTMPAllocTxRxRingMemory, Status=0 get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) pci probe count=2 Ralink APSoC Hardware Watchdog Timer Netfilter messages via NETLINK v0.30 with ipset netlink.patch. nf_conntrack version 0.5.0 (3915 buckets, 15660 max) nf_conntrack_rtsp v0.6.21 loading IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. GRE over IPv4 demultiplexor driver gre: can't add protocol nf_nat_rtsp v0.6.21 loading ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 10 NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NOTIFY NOTIFY NOTIFY NOTIFY NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 L2TP IP encapsulation support (L2TPv3) L2TP netlink interface L2TP ethernet pseudowire support (L2TPv3) 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 212k freed Algorithmics/MIPS FPU Emulator v1.5 init started: BusyBox v1.12.1 (2019-07-05 11:16:38 CST) starting pid 1, tty '': '/usr/etc/rcS' mount: mounting none on /dev/pts failed: No such file or directory mount: mounting none on /proc/bus/usb failed: No such file or directory mknod: /dev/fuse: File exists Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= [board_init/board_init.c::configure_mt7621_register():32] set from jtag to gpio mode [SYSTEM]/sbin/reg s 0 switch register base addr to system register 0xbe000000 [SYSTEM]/sbin/reg r 0x60a85a8 m [SYSTEM]/sbin/reg w 0x60 0xwrite offset 0x60, value 0xa05a8 a05a8 ^[[2;1;1;112;112;1;0x[SYSTEM]/sbin/reg r 0x60a05a8 m ^[[2;1;1;112;112[SYSTEM]/bin/echo 1 > /proc/sNOTIFY ys/net/ipv6/confNOTIFY /all/disable_ipvNOTIFY 6 ;1;0xNOTIFY NOTIFY NOTIFY NOTIFY NOTIFY [SYSTEM]/bin/echo ==============insmod start > /dev/console ==============insmod start [SYSTEM]/sbin/insmod /lib/modules/`uname -r`/kernel/drivers/char/i2c_drv.ko i2cdrv_major = 218 [SYSTEM]/sbin/insmod /lib/modules/led_pb_api.ko led_pb_api: module license 'Sercomm' taints kernel. Disabling lock debugging due to kernel taint [SYSTEM]/sbin/insmod /lib/modules/led_hw.koinit led gpio 17 Register LED ID <45> init led gpio 5 Register LED ID <44> init button gpio 12 Register LED ID <90> init button gpio 18 Register LED ID <91> init button gpio 14 Register LED ID <92> init led gpio 178 this is i2c exp Register LED ID <71> init led gpio 179 this is i2c exp Register LED ID <70> init led gpio 180 this is i2c exp Register LED ID <30> init led gpio 181 this is i2c exp Register LED ID <20> init led gpio 182 this is i2c exp Register LED ID <41> init led gpio 183 this is i2c exp Register LED ID <42> init led gpio 184 this is i2c exp Register LED ID <61> init led gpio 185 this is i2c exp Register LED ID <60> init led gpio 170 this is i2c exp Register LED ID <13> init led gpio 171 this is i2c exp Register LED ID <12> init led gpio 172 this is i2c exp Register LED ID <15> init led gpio 173 this is i2c exp Register LED ID <14> init led gpio 174 this is i2c exp Register LED ID <17> init led gpio 175 this is i2c exp Register LED ID <16> init led gpio 176 this is i2c exp Register LED ID <19> init led gpio 177 this is i2c exp Register LED ID <18> [SYSTEM]/sbin/insmod /lib/modules/2.6.30.9/kernel/fs/jbd2/jbd2.ko insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/jbd2/jbd2.ko': No such file or directory [SYSTEM]/sbin/insmod /lib/modules/2.6.30.9/kernel/fs/ext4/ext4.ko insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/ext4/enetfilter dnshj choose interested dns queries module loaded ! xt4.ko': No such file or directory [SYSTEM]/sbin/insmod /lib/modules/ipt_condition.ko [SYSTEM]/sbin/insmod /lib/modules/ipt_http_string.ko [SYSTEM]/sbin/insmod /lib/modules/ipt_dnshj.ko [SYSTEM]/sbin/insmod /lib/modules/ipt_DLOG.ko [SYSTEM]/sbin/insmod /lib/modules/ipt_macblock_dnshj.ko insmod: can't read '/lib/modules/ipt_macblock_dnshj.ko': No such file or directory [SYSTEM]/sbin/insmod /lib/modules/xt_ct_dir.ko [SYSTEM]/sbin/insmod /lib/modules/cnapt_core.ko [SYSTEM]/sbin/insmod /lib/modules/cnapt.ko [SYSTEM]/sbin/insmod /lib/modules/cpt.ko [SYSTEM]/sbin/insmod /lib/modules/cpm.ko [SYSTEM]/sbin/insmod /lib/modules/calg.ko [SYSTEM]/sbin/insmod /lib/modules/cdmz.ko [SYSTEM]/sbin/insmod /lib/modules/cudp.ko [SYSTEM]/sbin/insmod /lib/modules/hairpin.ko [SYSTEM]/sbin/insmod /lib/modules/natlimit.ko [SYSTEM]/sbin/insmod /lib/modules/jnl.ko jnl: driver (UFSD_HEAD lke_9.4.4_b3, LBD=ON) loaded at c0ab5000 [SYSTEM]/sbin/insmod /lib/modules/ufsd.ko ufsd: driver (UFSD_HEAD lke_9.4.4_b3, paragon, ioctl, sd2(5), tr, car) loaded at c0b7f000 NTFSJ support included Build_for__Netgear_R6800_k2.6.36_2016-11-09_lke_9.4.4_b3 ufsd Kernel .config hash: original 0x1086fa24, current can't check. [SYSTEM]/sbin/insmod /lib/modules/arp_protect_enable.ko [SYSTEM]/sbin/insmod /libinit common module successful /modules/common.ko [SYSTEM]/sbin/insmod /lib/modules/firewall_block.ko insert firewall block module success [SYSTEM]/sbin/insmod /lib/modules/fake_sourfake source dos protect modules is inserted ce_dos.ko [SYSTEM]/sbin/insmod /lib/modules/psd_and_special_udp_dos.ko netfilter PSD and TCP/UDP Echo/Chargen Attack loaded [SYSTEM]/sbin/insmod /lib/modules/tcp_syn_dnetfilter tcp syn flood module loaded os.ko [SYSTEM]/sbin/insmod /lib/modules/clamp_total_session_for_onetfilter clamp total session for one src ip module loaded ne_src.ko [SYSTEM]/sbin/insmod /lib/mnetfilter other dos module loaded odules/others_dos.ko [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/net/wireless/mt_wifi_ap/mt_wifi.ko insmod: can't read '/lib/modules/2.6.36/kernel/drivers/net/wireless/mt_wifi_ap/mt_wifi.ko': No such file or directory [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/fs/mbcache.ko [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/fs/jbd2/jbd2.ko [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/fs/ext4/ext4.ko [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/fs/hfsplus_journal/hfsplus.ko [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/core/usbcore.ko usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/host/xhci-hcd.ko FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1 xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/storage/usb-storage.ko Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/serial/usbserial_filter.ko insmod: can't read '/lib/modules/2.6.36/kernel/drivers/usb/serial/usbserial_filter.ko': No such file or directory [SYSTEM]/bin/echo ==============insmod finish > /dev/console =====NOTIFY =========insmod FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF finish )SYRaeth v3.1 (STEM]/sbin/ifconTaskletfig eth2 up set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 phy_free_head is 0xca0000!!! phy_free_tail_phy is 0xca1ff0!!! txd_pool=a0ca8000 phy_txd_pool=00CA8000 ei_local->skb_free start address is 0x8ff1a69c. free_txd: 00ca8010, ei_local->cpu_ptr: 00CA8000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa0ca8000 0x00CA8000 0x00CA8000 phy_qrx_ring = 0x00ca2000, qrx_ring = 0xa0ca2000 phy_rx_ring0 = 0x00ca4000, rx_ring0 = 0xa0ca4000 MT7530 Reset Completed!! change HW-TRAP to 0x17c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x432880e5 GDMA2_MAC_ADRH -- : 0x0000000c GDMA2_MAC_ADRL -- : 0x432880ac NOTIFY NOTIFY eth3: ===> VirtualIF_open MT7621 GE2 link rate to 1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 NOTIFY [SYSTEM]/sbin/ifconfig lo 1NOTIFY 27.0.0.0 NOTIFY [SYSTEM]/sbin/route add -net 127.0.0.0 netmask 255.0.0.0 lo [SYSTEM]/bin/cp /proc/uptime /tmp/lan_uptime [SYSTEM]/sbin/ifconfig eth2.1 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ifconfigNOTIFY eth2.2 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ifconfig eth2 down ra2880stop()...Done eth3: ===> VirtualIF_close Free TX/RX Ring Memory! NOTIFY [SYSTEM]/sbin/vconfig rem eth2.1 vconfig: ioctl error for rem: No such device [SYSTEM]/sbin/vconfig rem ethNOTIFY 2.2 vconfigFFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF : ioctl error foRaeth v3.1 (r rem: No such dTaskletevice [SYS) TEM]/sbin/ifconfig eth2 up set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 phy_free_head is 0xca0000!!! phy_free_tail_phy is 0xca1ff0!!! txd_pool=a0ca8000 phy_txd_pool=00CA8000 ei_local->skb_free start address is 0x8ff1a69c. free_txd: 00ca8010, ei_local->cpu_ptr: 00CA8000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa0ca8000 0x00CA8000 0x00CA8000 phy_qrx_ring = 0x00ca2000, qrx_ring = 0xa0ca2000 phy_rx_ring0 = 0x00ca4000, rx_ring0 = 0xa0ca4000 MT7530 Reset Completed!! change HW-TRAP to 0x17c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x432880e5 eth3: ===> VirtualIF_open MT7621 GE2 link rate to 1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 NOTIFY [SYSTEM]/sbin/ifconfig eth2NOTIFY down ra2880stop()...Done eth3: ===> VirtualIF_close Free TX/RX Ring Memory! NOTIFY [SYSTEM]/sbin/ifconfig eth2NOTIFY hw ether B0:39:56:52:21:FC [SYSTEM]/NOTIFY sbin/ifconfig etFFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF h2 up Raeth v3.1 (Tasklet) set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 phy_free_head is 0xca0000!!! phy_free_tail_phy is 0xca1ff0!!! txd_pool=a0ca8000 phy_txd_pool=00CA8000 ei_local->skb_free start address is 0x8ff1a69c. free_txd: 00ca8010, ei_local->cpu_ptr: 00CA8000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa0ca8000 0x00CA8000 0x00CA8000 phy_qrx_ring = 0x00ca2000, qrx_ring = 0xa0ca2000 phy_rx_ring0 = 0x00ca4000, rx_ring0 = 0xa0ca4000 MT7530 Reset Completed!! change HW-TRAP to 0x17c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000b039 GMAC1_MAC_ADRL -- : 0x565221fc eth3: ===> VirtualIF_open MT7621 GE2 link rate to 1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 NOTIFY [SYSTEM]/usr/sbin/config-vlan.sh 3 0 restore GSW to dump switch mode switch reg write offset=2004, value=ff0000 switch reg write offset=2104, value=ff0000 switch reg write offset=2204, value=ff0000 switch reg write offset=2304, value=ff0000 switch reg write offset=2404, value=ff0000 switch reg write offset=2504, value=ff0000 switch reg write offset=2604, value=ff0000 switch reg write offset=2704, value=ff0000 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=810000c0 switch reg write offset=2710, value=810000c0 REG_ESW_WT_MAC_ATC is 0x7ff0002 done. [SYSTEM]/usr/sbin/echo '##### config Switch vlan partition (LLLLW) #####' ##### config Switch vlan partition (LLLLW) ##### [SYSTEM]/usr/sbin/switch vlan set 1 1 11110011 [SYSTEM]/usr/sbin/switch vlan set 2 2 00001100 [SYSTEM]/usr/sbin/switch pvid 4 2 Set port 4 pvid 2. [SYSTEM]/usr/sbin/switch pvid 5 2 Set port 5 pvid 2. [SYSTEM]/usr/sbin/switch reg w 2004 ff0003 switch reg write offset=2004, value=ff0003 [SYSTEM]/usr/sbin/switch reg w 2104 ff0003 switch reg write offset=2104, value=ff0003 [SYSTENOTIFY M]/usr/sbin/switeth3: ===> VirtualIF_open ch reg w 2204 ffNOTIFY 0003 switch reg write offset=2204, value=ff0003 [SYSTEM]/usr/sbin/switch reg w 2304 ff0003 switch reg write offset=2304, value=ff0003 [SYSTEM]/usr/sbin/switch reg w 2404 ff0003 switch reg write offset=2404, value=ff0003 [SYget_wdev_by_idx: invalid idx(0) STEM]/usr/sbin/sget_wdev_by_idx: invalid idx(0) witch reg w 2504get_wdev_by_idx: invalid idx(0) ff0003 swiget_wdev_by_idx: invalid idx(0) tch reg write ofget_wdev_by_idx: invalid idx(0) fset=2504, valueget_wdev_by_idx: invalid idx(0) =ff0003 [Sget_wdev_by_idx: invalid idx(0) YSTEM]/usr/sbin/get_wdev_by_idx: invalid idx(0) switch reg w 260get_wdev_by_idx: invalid idx(0) 4 ff0003 swget_wdev_by_idx: invalid idx(0) itch reg write offset=2604, value=ff0003 [SYSTEM]/sbin/ifconfig eth3 up [SYSTEM]/usr/sbin/led_switch & [SYSTEM]/usr/sbin/mknod /dev/apsoc_nvram c 251 0 [modelinfo_product_id.c::modelinfo_map_index():123] 0x30 0x36, 0x3036. find index 0 for modelinfo_get_product_name [modelinfo_product_id.c::modelinfo_get_guest_led_replace_usb_led():281] guest_led_replace_usb_led is 0 [flash.c::sc_get_region():632] Original Region Data: 00, 02 [init/init_cfg.c::rc_init():706] region valid nvram commit! RC: wifi_init() [SYSTEM]/usr/bin/killall access_logd killall: access_logd: no process killed get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) usb printer event [SYSTEM]/usr/sbin/rc access_log start ESW: Link Status Changed - Port3 Link UP rcd: enQ=/usr/sbin/rc_app/rc_access_log start rcd: [run] deQ =/usr/sbin/rc_app/rc_access_log start [SYSTEM]/usr/sbin/rcget_wdev_by_idx: invalid idx(0) access_dev starget_wdev_by_idx: invalid idx(0) t rcd: enQ=get_wdev_by_idx: invalid idx(0) /usr/sbin/rc_appget_wdev_by_idx: invalid idx(0) /rc_access_dev sget_wdev_by_idx: invalid idx(0) tart [modelinfget_wdev_by_idx: invalid idx(0) o_product_id.c::get_wdev_by_idx: invalid idx(0) modelinfo_map_inget_wdev_by_idx: invalid idx(0) dex():123] 0x30 get_wdev_by_idx: invalid idx(0) 0x36, 0x3036. get_wdev_by_idx: invalid idx(0) find index 0 for modelinfo_get_product_name saved_index:0 [modelinfo_product_id.c::modelinfo_set_autoupg_fileinfo():263] autoupg_fileinfo_in_nv is fileinfo.txt [SYSTEM]/usr/bin/insmod /lib/modules/ufsd.ko killall: access_logd: no process killed insmod: cannot insert '/lib/modules/ufsd.ko': File exists saved_index:0 saved_index:0 [modelinfo_product_id.c::modelinfo_set_autoupg_fileinfo():263] autoupg_fileinfo_in_nv is fileinfo.txt [init/init_cfg.c::rc_init():8get_wdev_by_idx: invalid idx(0) 98] tm sync doneget_wdev_by_idx: invalid idx(0) [init/init_cfg.c::rc_init():939] not enable tc from old since this not from old fw [SYSTEM]/sbin/rc rwfs start rcd: enQ=/usr/sbin/rc_app/rc_rwfs start [SYSTEM]/sbin/rc led_ctrl start rcd: enQ=/usr/sbin/rc_app/rc_led_ctrl start [SYSTEM]/bin/echo ===============rc start > /dev/console ===============rc start [SYSTEM]/sbin/klogd& [SYSTEM]/usr/sbin/cmd_agent_ap [SYSTEM]/usr/sbin/cmd_agent& [SYSTEM]/usr/sbin/scfgmgr& [SYSTEM]/sbin/lan_monitor & /bin/sh: /sbin/lan_monitor: not found [SYSTEM]/sbin/rc syslogd start rcd: enQ=/usr/sbin/rc_app/rc_syslogd start [SYSTEM]/sbin/rc wlan start [flash.c::sc_check_remotescfgmgrmagic():1357] buf:ff, ff, ff, ff [flash.c::sc_check_remotescfgmgrmagic():1359] magic:31, 3e, c5, 8d rcd: enQ=/usr/sbin/rc_app/rc_wlan start [SYSTEM]/sbin/rc lan init scfgmgr for local rcd: enQ=/usr/sbin/rc_app/rc_lan init [SYSTEM]/sbin/rc firewall init rcd: enQ=/usr/sbin/rc_app/rc_firewall init [SYSTEM]/sbin/rc vlan start rcd: enQ=/usr/sbin/rc_app/rc_vlan start [SYSTEM]/sbin/rc funjsq start rcd: enQ=/usr/sbin/rc_app/rc_funjsq start [SYSTEM]/sbin/rc lan start rcd: enQ=/usr/sbin/rc_app/rc_lan start [SYSTEM]/sbin/rc lan reset_switch rcd: enQ=/usr/sbin/rc_app/rc_lan reset_switch [SYSTEM]/sbin/rc wifi_isolation start rcd: enQ=/usr/sbin/rc_app/rc_wifi_isolation start [SYSTEM]/sbin/rc timezone start rcd: enQ=/usr/sbin/rc_app/rc_timezone start [SYSTEM]/sbin/rc sip_alg start rcd: enQ=/usr/sbin/rc_app/rc_sip_alg start [SYSTEM]/sbin/rc mediaserver start rcd: enQ=/usr/sbin/rc_app/rc_mediaserver start [SYSTEM]/sbin/rc dnrd start rcd: enQ=/usr/sbin/rc_app/rc_dnrd start [SYSTEM]/sbin/rc debug_mode start& [SYSTEM]/sbin/rc httpd start rcd: enQ=/usr/sbin/rc_app/rc_debug_mode start rcd: enQ=/usr/sbin/rc_app/rc_httpd start [SYSTEM]/sbin/rc httpd remote start rcd: enQ=/usr/sbin/rc_app/rc_httpd remote start [SYSTEM]/sbin/rc printk start rcd: enQ=/usr/sbin/rc_app/rc_printk start [SYSTEM]/sbin/rc ntp start rcd: enQ=/usr/sbin/rc_app/rc_ntp start [SYSTEM]/sbin/rc ddns init rcd: enQ=/usr/sbin/rc_app/rc_ddns init [SYSTEM]/sbin/rc wan init rcd: enQ=/usr/sbin/rc_app/rc_wan init [SYSTEM]/sbin/rc route start rcd: enQ=/usr/sbin/rc_app/rc_route start [SYSTEM]/sbin/rc ripd start rcd: enQ=/usr/sbin/rc_app/rc_ripd start [SYSTEM]/sbin/rc potcounter start rcd: enQ=/usr/sbin/rc_app/rc_potcounter start [SYSTEM]/sbin/rc lltd start rcd: enQ=/usr/sbin/rc_app/rc_lltd start [SYSTEM]/sbin/rc upnp start rcd: enQ=/usr/sbin/rc_app/rc_upnp start [SYSTEM]/sbin/rc schedule start rcd: enQ=/usr/sbin/rc_app/rc_schedule start [SYSTEM]/sbin/rc usb_service init rcd: enQ=/usr/sbin/rc_app/rc_usb_service init [SYSTEM]/sbin/rc vlan start rcd: enQ=/usr/sbin/rc_app/rc_vlan start [SYSTEM]/sbin/rc dbus start rcd: enQ=/usr/sbin/rc_app/rc_dbus start [SYSTEM]/sbin/rc xCloud start rcd: enQ=/usr/sbin/rc_app/rc_xCloud start [SYSTEM]/sbin/rc access_dev start rcd: enQ=/usr/sbin/rc_app/rc_access_dev start [SYSTEM]/sbin/rc accessctl_block restart rcd: enQ=/usr/sbin/rc_app/rc_accessctl_block restart [SYSTEM]/sbin/rc openvpn prepare rcd:watchdog (557): /proc/557/oom_adj is deprecated, please use /proc/557/oom_score_adj instead. enQ=/usr/sbin/rStarted WatchDog Timer. c_app/rc_openvpn prepare [SYSTEM]/etc/ad_arpd & [SYSTEM]/usr/sbin/crond & [SYSTEM]/usr/sbin/multi_pb_app 90 91 92 0 50& [SYSTEM]/usr/sbin/wlevt /bin/sInit kernel monitor... h: /usr/sbin/wlevt: not found [SYSTEM]/etc/prepare_3g preapre_sys_for_3g mknod: /dev/zero: File exists mknod: /dev/ttyUSB0: File exists mknod: /dev/ttyUSB1: File exists mknod: /dev/ttyUSB2: File exists mknod: /dev/ttyUSB3: File exists mkdir: cannot create directory '/var': File exists preapre_sys_for_3g done [SYSTEM]/usr/sbin/rc usb_printer start rcd: enQ=/usr/sbin/rc_app/rc_usb_printer start [SYSTEM]/etc/turn_on_printer_led [SYSTEM]/bin/rc wan apcli_rc_ready rcd: enQ=/usr/sbin/rc_app/rc_wan apcli_rc_ready rcd: enQ=/usr/sbin/rc_app/rc_check_conn start [SYSTEM]/usr/sbin/pot_daemon & [SYSTEM]/sbin/scm_watchdog & [SYSTEM]/sbin/kwilt_daemon & [SYSTEM]/usr/sbin/wdg.sh [SYSTEM]/usr/sbin/ln -sf /usr/sbin/curl /tmp/curl_for_kwilt [kwilt_daemon.c::start_check_kwilt():672] check if kwilt ready for check [watchdog.c::main():113] Watchdog: monitoring process '/usr/sbin/mini_httpd' [watchdog.c::main():113] Watchdog: monitoring process '/bin/mini_httpd' [watchdog.c::main():113] Watchdog: monitoring process 'nmbd' [watchdog.c::main():113] Watchdog: monitoring process 'smbd' [watchdog.c::main():113] Watchdog: monitoring process 'syslogd' [watchdog.c::main():129] Watchdog: process '/usr/sbin/mini_httpd' should exist, but it does not exist, score: 5! [SYSTEM]/usr/sbin/watchdog wd set oom_adj /proc/557/oom_adj -17 wd set schedprio 99 ok SCHED_FIFO [SYSTEM]/sbin/insmod /lib/modules/hal_wd.ko [SYSTEM]/usr/sbin/cmd_agent_ap_RAE [SYSTEM]/sbin/rc RAE start rcd: enQ=/usr/sbin/rc_app/rc_RAE start [SYSTEM]/sbin/rc start finished rcd: enQ=/usr/sbin/rc_app/rc_start finished [SYSTEM]/bin/echo ===============rc finish > /dev/console ===============rc finish [SYSTEM]/bin/ps PID USER VSZ STAT COMMAND 1 root 1556 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW [kworker/u:0] 6 root 0 SW [migration/0] 7 root 0 SW [migration/1] 8 root 0 SW [kworker/1:0] 9 root 0 SW [ksoftirqd/1] 10 root 0 SW [migration/2] 11 root 0 SW [kworker/2:0] 12 root 0 SW [ksoftirqd/2] 13 root 0 SW [migration/3] 14 root 0 SW [kworker/3:0] 15 root 0 SW [ksoftirqd/3] 16 root 0 SW< [khelper] 17 root 0 SW [kworker/3:1] 18 root 0 SW [kworker/2:1] 19 root 0 SW [kworker/1:1] 20 root 0 SW [sync_supers] 21 root 0 SW [bdi-default] 22 root 0 SW< [kblockd] 23 root 0 SW [kswapd0] 24 root 0 SW [fsnotify_mark] 25 root 0 SW< [crypto] 34 root 0 SW [mtdblock0] 35 root 0 SW [mtdblock1] 36 root 0 SW [mtdblock2] 37 root 0 SW [mtdblock3] 38 root 0 SW [mtdblock4] 39 root 0 SW [mtdblock5] 40 root 0 SW [mtdblock6] 41 root 0 SW [mtdblock7] 42 root 0 SW [mtdblock8] 43 root 0 SW [mtdblock9] 44 root 0 SW [mtdblock10] 45 root 0 SW [mtdblock11] 46 root 0 SW [mtdblock12] 47 root 0 SW [mtdblock13] 48 root 0 SW [mtdblock14] 49 root 0 SW [mtdblock15] 50 root 0 SW [mtdblock16] 51 root 0 SW [mtdblock17] 52 root 0 SW [mtdblock18] 53 root 0 SW [mtdblock19] 54 root 0 SW [mtdblock20] 55 root 0 SW [mtdblock21] 56 root 0 SW [mtdblock22] 57 root 0 SW [mtdblock23] 58 root 0 SW [mtdblock24] 59 root 0 SW [mtdblock25] 60 root 0 SW [mtdblock26] 61 root 0 SW [mtdblock27] 62 root 0 SW [mtdblock28] 63 root 0 SW [kworker/u:1] 70 root 0 SW [kworker/0:1] 72 root 1556 S /bin/sh /usr/etc/rcS 135 root 0 DW [i2c_drv_thread] 206 root 0 SW [khubd] 301 root 1704 S /usr/sbin/led_switch 331 root 1552 S /bin/sh -c /bin/sleep 10 && /bin/rc usb_service led_u 332 root 1548 S /bin/sleep 10 336 root 1208 S /usr/sbin/rcd 337 root 0 [] 346 root 3872 S /usr/sbin/rc_app/rc_start 364 root 1192 S /sbin/klogd 371 root 1192 S /usr/sbin/cmd_agent_ap 377 root 1196 S /usr/sbin/cmd_agent 388 root 1692 S /usr/sbin/scfgmgr 451 root 1552 S /bin/sh /etc/ad_arpd 454 root 1216 S /usr/sbin/crond 456 root 1736 S /usr/sbin/multi_pb_app 90 91 92 0 50 466 root 1548 S sleep 30 532 root 1388 S /usr/sbin/pot_daemon 534 root 1376 S /sbin/scm_watchdog 536 root 1724 S /sbin/kwilt_daemon 557 root 1204 S /usr/sbin/watchdog Access Control log start. rcd: [run] deQ =/usr/sbin/rc_app/rc_access_dev start 562 root 1192 S /usr/sbin/cmd_agent_ap_RAE 569 root 1552 S /bin/sh -c /bin/ps Access Control socket create 570 root 1556 R /bin/ps run smp wifi killall: access_devinfo: no process killed smp.sh:dhcpc wifi /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/apcli0/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/apclii0/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/wds0/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/wds1/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/wds2/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/wds3/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/wdsi0/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/wdsi1/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/wdsi2/queues/rx-0/rps_cpus: nonexistent directory /etc/mtk/mt7621_smp.sh: line 179: cannot create /sys/class/net/wdsi3/queues/rx-0/rps_cpus: nonexistent directory eth2/eth3 RPS: CPU0/2 run smp wifi done =============proc init /bin/sh: cannot create /proc/sys/net/ipv4/conf/group1/forwarding: nonexistent directory /bin/sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory /bin/sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory /bin/sh: cannot create /proc/sys/net/ipv4/conf/eth1/rp_filter: nonexistent directory [SYSTEM]/bin/echo 8 > /proc/sys/kernel/printk =============proc finish starting pid 1, tty '/dev/ttyS1': '/bin/sh' # 1;1;112;112;1;0x1;1;112;112;1;0xget_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) Access Control socket create rcd: [run] deQ =/usr/sbin/rc_app/rc_rwfs start [SYSTEM]/usr/sbin/mknod /dev/mtd28 c 90 56 [SYSTEM]/usr/sbin/mknod /dev/mtdblock28 b 31 28 [SYSTEM]/usr/sbin/umount /tmp/RWFS/ umount: can't umount /tmp/RWFS/: No such file or directory [SYSTEM]/usr/sbin/ubidetach /dev/ubi_ctrl -m 28 ubidetach: error!: cannot detach mtd28 error 19 (No such device) [rwfs/rw_fs_setup.c::rwfs_mtd_has_correct_fs_magic():62] block 0 header:55 42 49 23 1 [rwfs/rw_fs_setup.c::rwfs_mtd_has_correct_fs_magic():66] skipped 0 blockUBI: attaching mtd28 to ubi0 and find a ubi UBI: physical eraseblock size: 131072 bytes (128 KiB) magic [SYSUBI: logical eraseblock size: 126976 bytes TEM]/usr/sbin/rmUBI: smallest flash I/O unit: 2048 -rf /dev/ubi_ctUBI: VID header offset: 2048 (aligned 2048) rl [SYUBI: data offset: 4096 STEM]/usr/sbin/mknod /dev/ubi_ctrl c 10 61 [SYSTEM]/usr/sbin/ubiattach /dev/ubi_ctrl -m 28 UBI: max. sequence number: 27 UBI: attached mtd28 to ubi0 UBI: MTD device name: "Reserved Block6" UBI: MTD device size: 33 MiB UBI: number of good PEBs: 268 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 14 UBI: total number of reserved PEBs: 254 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/1 UBI: image sequence number: 856848203 UBI: background thread "ubi_bgt0d" started, PID 694 UBI device number 0, total 268 LEBs (34029568 bytes, 32.5 MiB), available 14 LEBs (1777664 bytes, 1.7 MiB), LEB size 126976 bytes (124.0 KiB) [SYSTEM]/usr/sbin/rm -rf /dev/ubi0 [SYSTEM]/usr/sbin/mknod /dev/ubi0 c 250 0 UBI error: ubi_create_volume: cannot create volume 1, error -17 [SYSTEM]/usr/sbin/ubimkvol /dev/ubi0 -N vol_name -s 30MiB ubimkvol: error!: cannot UBI create volume error 17 (File exists) [SYSTEM]/usr/sbin/mkdir /tmp/RWFS/ [SYSTEM]/usr/sbin/mount -t ubifs ubi0:vol_name /tmp/RWFS/ UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "vol_name" UBIFS: file system size: 30347264 bytes (29636 KiB, 28 MiB, 239 LEBs) UBIFS: journal size: 1523712 bytes (1488 KiB, 1 MiB, 12 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 1433376 bytes (1399 KiB) [SYSTEM]/usr/sbin/touch /tmp/RWFS//ready [rwfs/rw_fs_setup.c::start_rwfs():220] rwfs mounted ok rcd: [run] deQ =/usr/sbin/rc_app/rc_led_ctrl start [SYSTEM]/bin/led_app ctrl blink_data sc_do_led_ctrl_ioctl:171 set ctrl to 0 rcd: [run] deQ =/usr/sbin/rc_app/rc_syslogd start [SYSTEM]/sbin/syslogd -f /etc/syslog.conf rcd: [run] deQ =/usr/sbin/rc_app/rc_wlan start [wlan/wifi.c::sync_wireless_nvram():2361] wifi_super_wifi_enable:0, wifi_powerpercent:100, wifi_super_wifi_enable1:0, wifi_powerpercent1:100 [SYSTEM]mkdir -p /etc/Wireless/RT2860 [ create_ralink_driver_conf - 773 ] : dfs:1 [wlan/wifi.c::create_ralink_driver_conf():917] no need PERCENTAGEenable for 2G value 100 [modelinfo_product_id.c::modelinfo_map_index():123] 0x30 0x36, 0x3036. find index 0 for modelinfo_get_product_name [SYSTEM]mkdir -p /etc/Wireless/iNIC [ create_ralink_driver_conf - 773 ] : dfs:1 [wlan/wifi.c::create_ralink_driver_conf():917] no need PERCENTAGEenable for 5G value 100 [SYSTEM]echo 1 > /tmp/apcli_wifi_if_inited [SYSTEM]echo 1 > /tmp/apcli_wifi_if_inited1 [wlan/wifi.c::start_wireless():2521] Check WiFi Config. [wlan/wifi.c::start_wireless():2530] Check 11AC support. saved_index:0 [wlan/wifi.c::start_wireless():2532] SC 5G support level: 11ac [wlan/wifi.c::start_wireless():2534] Check guest_led REPLACE usb_led. saved_index:0 [modelinfo_product_id.c::modelinfo_get_guest_led_replace_usb_led():281] guest_led_replace_usb_led is 0 [SYSTEM]/bin/led_app setval guest_led_replace 0 saved_index:0 [modelinfo_product_id.c::modelinfo_get_guest_led_replace_usb_led():281] guest_led_replace_usb_led is 0 [wlan/wifi.c::start_wireless():2539] guest_led REPLACE usb_led: OFF [wlan/wifi.c::prepare_single_sku_simple():2012] check if location has singlesku.dat [wlan/wifi.c::prepare_single_sku_simple():2035] done [wlan/wifi.c::prepare_single_sku_simple():2039] try find region:Europe [wlan/wifi.c::prepare_single_sku_simple():2045] find region:Europe, use:CE [SYSTEM]/bin/mkdir -p /etc_ro/Wireless/RT2860AP/ [SYSTEM]/bin/rm -rf /etc_ro/Wireless/RT2860AP//7615_SingleSKU.dat [SYSTEM]/bin/rm -rf /etc_ro/Wireless/RT2860AP//7615_SingleSKU_BF.dat [wlan/wifi.c::prepare_single_sku_simple():2095] not Canada/India/Korea region [SYSTEM]/bin/cp /etc/mtk/singlesku_r6950//CE/7615_SingleSKU.dat /etc_ro/Wireless/RT2860AP// [SYSTEM]/bin/cp /etc/mtk/singlesku_r6950//CE/7615_SingleSKU_BF.dat /etc_ro/Wireless/RT2860AP// [wlan/wifi.c::prepare_single_sku_simple():2156] not generate power table md5 [libscm_wl.c::set_ralink_wifi_mac():1702] CHIP: 7615 - current MAC: B0:39:56:52:21:FC [libscm_wl.c::set_ralink_wifi_mac():1703] Assign MAC: B0:39:56:52:21:FC [libscm_wl.c::set_ralink_wifi_mac():1706] no update! get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) [libscm_wl.c::set_ralink_wifi_mac():1702] CHIP: 7615 - current MAC: B0:39:56:52:21:FD [libscm_wl.c::set_ralink_wifi_mac():1703] Assign MAC: B0:39:56:52:21:fd [libscm_wl.c::set_ralink_wifi_mac():1706] no update! [SYSTEM]echo 1 > /tmp/wifi_mac_set [SYSTEM]/sbin/ifconfig ra0 NOTIFY up get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) DriverOwn()::Return since already in Driver Own... =============================== Current DevInfo Num: 0 =============================== =============================== Current BssInfo Num: 0 =============================== =============================== Current StaRec Num: 0 =============================== APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860_5G.dat Open file "/etc/Wireless/RT2860/RT2860_5G.dat" failed! E2pAccessMode=2 SSID[0]=NETGEAR66, EdcaIdx=0 SSID[1]=NETGEAR_Guest, EdcaIdx=0 RTMPSetProfileParameters(): DBDC Mode=0 cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! BandSteering=1 [TxPower] BAND0: 100 [SKUenable] BAND0: 1 APEdca0 APEdca1 APEdca2 APEdca3 APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 default ApCliAPSDCapable[1]=0 [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 rtmp_read_wds_from_file(): WDS Profile APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] WDS-Enable mode=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: Ext Channel = BELOW HT: greenap_cap = 0 IcapMode = 0 WtcSetMaxStaNum: MaxStaNum:86, BssidNum:2, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124 Top Init Done! Use dev_alloc_skb RX[0] DESC a0c0a000 size = 8192 RX[1] DESC a0c0c000 size = 8192 Hif Init Done! ctl->txq = c04fa968 ctl->rxq = c04fa974 ctl->ackq = c04fa980 ctl->kickq = c04fa98c ctl->tx_doneq = c04fa998 ctl->rx_doneq = c04fa9a4 mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2725): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1043), cap->rom_patch_len(11150) AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 20170714031500a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=2 MtCmdPatchSemGet:(ret = 0) Patch is not ready && get semaphore success, SemStatus(2) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Send checksum req.. Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(810), cap->fw_len(459768) Build Date:_201708100317 Build Date:_201708100317 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201707261512 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done! efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] NICReadEEPROMParameters():Calling eeinit NICReadEEPROMParameters: EEPROM 0x52 b302 NICReadEEPROMParameters: EEPROM 0x52 b302 Country Region from e2p = 101 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 rtmp_read_txpwr_from_eeprom(243): Don't Support this now! RTMPReadTxPwrPerRate(1382): Don't Support this now! RcRadioInit(): DbdcMode=0, ConcurrentBand=1 RcRadioInit(): pRadioCtrl=8fc87450,Band=0,rfcap=3,channel=1,PhyMode=2 MtCmdSetDbdcCtrl:(ret = 0) rcd: enQ=/usr/sbin/rc_app/rc_usb_service led_update Band Rf: 1, Phy Mode: 2 AntCfgInit(2779): Not support for HIF_MT yet! MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2787): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c MtAsicSetMacMaxLen(1313): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! MtCmdSetMacTxRx:(ret = 0) CountryCode(2.4G/5G)=1/1, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels WifiSysOpen(), wdev idx = 0 wdev_attr_update(): wdevId0 = b0:39:56:52:21:fc MtCmdSetDbdcCtrl:(ret = 0) ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup = 0, AutoChannelFlag = 0 ApAutoChannelAtBootUp<----------------- MtAsicSetChBusyStat(865): Not support for HIF_MT yet! [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=12 CountryCode(2.4G/5G)=1/1, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels Enable 20/40 BSSCoex Channel Scan(BssCoex=1) MtCmdSetMacTxRx:(ret = 0) mt7615_apply_dcoc() : reload Central CH [5] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [6] BW [0] from cetral freq [2432] offset [2300] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [7] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) mt7615_apply_dcoc() : reload Central CH [8] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [9] BW [0] from cetral freq [2447] offset [2400] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [10] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [11] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 11,control_ch2=0, central_chl = 11 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [12] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 12,control_ch2=0, central_chl = 12 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l mt7615_apply_dcoc() : reload Central CH [13] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 13,control_ch2=0, central_chl = 13 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(1) SYNC - BBP R4 to 20MHz.l wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 [RadarStateCheck]Set into RD_NORMAL_MODE MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 0 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 1 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 2 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 3 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 4 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 5 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 6 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) mt7615_bbp_adjust():rf_bw=0, ext_ch=0, PrimCh=12, HT-CentCh=12, VHT-CentCh=0 mt7615_apply_dcoc() : reload Central CH [12] BW [0] from cetral freq [2467] offset [2500] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 12,control_ch2=0, central_chl = 12 DBDCIdx= 0, Band= 0 BW = 0,TXStream = 4, RXStream = 4, scan(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 12(Prim=12, HT-CentCh=12, VHT-CentCh=0, BBP_BW=0) LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY MtAsicSetRalinkBurstMode(2618): Not support for HIF_MT yet! MtAsicSetPiggyBack(802): Not support for HIF_MT yet! MtAsicSetTxPreamble(2597): Not support for HIF_MT yet! RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! AndesLedEnhanceOP: Success! BndStrg_Init() BndStrg_SetInfFlags(): BSS (b0:39:56:52:21:fc) set 2G Inf ra0 ready. Main bssid = b0:39:56:52:21:fc AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn MtCmdSetMacTxRx:(ret = 0) fdb_enable() MCS Set = ff ff ff ff 01 <==== mt_wifi_init, Status=0 MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1 MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1 NOTIFY NOTIFY WDS_Init(): The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw NOTIFY NOTIFY The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw NOTIFY NOTIFY The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw NOTIFY NOTIFY The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw NOTIFY NOTIFY Total allocated 4 WDS interfaces! wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw NOTIFY NOTIFY WtcSetMaxStaNum: MaxStaNum:86, BssidNum:2, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. Correct apidx from 0 to 0 for WscUUIDInit Generate UUID for apidx(0) UUID: c01b4580, len = 16 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 b0 39 56 52 21 fc NOTIFY get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) [SYSTEM]/sbget_wdev_by_idx: invalid idx(0) in/brctl addif gget_wdev_by_idx: invalid idx(0) roup1 ra0 get_wdev_by_idx: invalid idx(0) interface ra0 does not exist! [SYSTEM]/bin/led_app on 40 Can't find DB for id==40 [SYSTEM]/bin/led_app on 41 [wlan/wifi.c::start_wireless():2601] no need fix f2 f3 value sinNOTIFY ce this is 54M tget_wdev_by_idx: invalid idx(0) arget power and get_wdev_by_idx: invalid idx(0) NTGR need other get_wdev_by_idx: invalid idx(0) value [SYSget_wdev_by_idx: invalid idx(0) TEM]/sbin/ifconfget_wdev_by_idx: invalid idx(0) ig rai0 up get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) DriverOwn()::Return since already in Driver Own... =============================== Current DevInfo Num: 0 =============================== =============================== Current BssInfo Num: 0 =============================== =============================== Current StaRec Num: 0 get_wdev_by_idx: invalid idx(0) =============================== APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/iNIC/iNIC_ap_5G.dat Open file "/etc/Wireless/iNIC/iNIC_ap_5G.dat" failed! E2pAccessMode=2 SSID[0]=NETGEAR66, EdcaIdx=0 SSID[1]=NETGEAR-5G_Guest, EdcaIdx=0 RTMPSetProfileParameters(): DBDC Mode=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Equal! BandSteering=1 [TxPower] BAND0: 100 [SKUenable] BAND0: 1 APEdca0 APEdca1 APEdca2 APEdca3 APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 default ApCliAPSDCapable[1]=0 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 rtmp_read_wds_from_file(): WDS Profile APWdsInitialize():WdsEntry[0] APWdsInitialize():WdsEntry[1] APWdsInitialize():WdsEntry[2] APWdsInitialize():WdsEntry[3] WDS-Enable mode=0 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD HT: Ext Channel = BELOW HT: greenap_cap = 0 IcapMode = 0 WtcSetMaxStaNum: MaxStaNum:86, BssidNum:2, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124 Top Init Done! Use dev_alloc_skb RX[0] DESC a0c18000 size = 8192 RX[1] DESC a0c1a000 size = 8192 Hif Init Done! ctl->txq = c097a968 ctl->rxq = c097a974 ctl->ackq = c097a980 ctl->kickq = c097a98c ctl->tx_doneq = c097a998 ctl->rx_doneq = c097a9a4 mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) mt7615_fw_prepare(2725): MT7615_E3, USE E3 patch and ram code binary image AndesMTLoadRomMethodFwDlRing(1043), cap->rom_patch_len(11150) AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) 20170714031500a platform = ALPS hw/sw version = 8a108a10 patch version = 00000010 Patch SEM Status=2 MtCmdPatchSemGet:(ret = 0) Patch is not ready && get semaphore success, SemStatus(2) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Send checksum req.. Patch SEM Status=3 MtCmdPatchSemGet:(ret = 0) Release patch semaphore, SemStatus(3) AndesMTEraseRomPatch WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 AndesMTLoadFwMethodFwDlRing(810), cap->fw_len(459768) Build Date:_201708100317 Build Date:_201708100317 AndesRestartCheck: Current TOP_MISC2(0x1) AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 1, address = 540672 EventGenericEventHandler: CMD Success Build Date:_201707261512 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 4, address = 0 EventGenericEventHandler: CMD Success WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 MCU Init Done! efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0x8000] NICReadEEPROMParameters():Calling eeinit NICReadEEPROMParameters: EEPROM 0x52 b302 NICReadEEPROMParameters: EEPROM 0x52 b302 Country Region from e2p = 101 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 rtmp_read_txpwr_from_eeprom(243): Don't Support this now! RTMPReadTxPwrPerRate(1382): Don't Support this now! RcRadioInit(): DbdcMode=0, ConcurrentBand=1 RcRadioInit(): pRadioCtrl=8e8a9450,Band=0,rfcap=3,channel=1,PhyMode=2 MtCmdSetDbdcCtrl:(ret = 0) Band Rf: 1, Phy Mode: 2 AntCfgInit(2779): Not support for HIF_MT yet! MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! EEPROM Init Done! mt_mac_init()--> mt_mac_pse_init(2787): Don't Support this now! mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c MtAsicSetMacMaxLen(1313): Not finish Yet! <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! tx_pwr_comp_init():NotSupportYet! MtCmdSetMacTxRx:(ret = 0) CountryCode(2.4G/5G)=1/1, RFIC=25, PHY mode(2.4G/5G)=49/49, support 19 channels WifiSysOpen(), wdev idx = 0 wdev_attr_update(): wdevId0 = b0:39:56:52:21:fd MtCmdSetDbdcCtrl:(ret = 0) ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup = 0, AutoChannelFlag = 0 ApAutoChannelAtBootUp<----------------- MtAsicSetChBusyStat(865): Not support for HIF_MT yet! [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=44 CountryCode(2.4G/5G)=1/1, RFIC=25, PHY mode(2.4G/5G)=49/49, support 19 channels wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 [RadarStateCheck]Set into RD_NORMAL_MODE MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 0 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 1 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 2 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 3 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 4 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 5 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) MtCmdTxPwrUpCtrl: ucBandIdx: 0, cPwrUpCat: 6 MtCmdTxPwrUpCtrl: cPwrUpValue: (0)-(0)-(0)-(0)-(0)-(0)-(0) mt7615_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=44, HT-CentCh=46, VHT-CentCh=42 mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] MtCmdGetRXDCOCCalResult:(ret = 0) mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 BW = 2,TXStream = 4, RXStream = 4, scan(0) :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=44, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2) [WrapDfsRadarDetectStart]: Band0Ch is 44[WrapDfsRadarDetectStart]: Band1Ch is 0LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY MtAsicSetRalinkBurstMode(2618): Not support for HIF_MT yet! MtAsicSetPiggyBack(802): Not support for HIF_MT yet! MtAsicSetTxPreamble(2597): Not support for HIF_MT yet! RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! AndesLedEnhanceOP: Success! BndStrg_Init() BndStrg_SetInfFlags(): BSS (b0:39:56:52:21:fd) set 5G Inf rai0 ready. Main bssid = b0:39:56:52:21:fd AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn MtCmdSetMacTxRx:(ret = 0) fdb_enable() [kwilt_daemon.c::start_check_kwilt():680] kwilt MCS Set = ff ff ff ff 01 wait for wan/usb<==== mt_wifi_init, Status=0 /non-blank MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1 MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1 NOTIFY NOTIFY WDS_Init(): The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 NOTIFY NOTIFY The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 NOTIFY NOTIFY The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 NOTIFY NOTIFY The new WDS interface MAC = FF:FF:FF:FF:FF:FF MacTabMatchWCID = 0 NOTIFY NOTIFY Total allocated 4 WDS interfaces! NOTIFY NOTIFY WtcSetMaxStaNum: MaxStaNum:86, BssidNum:2, WdsNum:4, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124 red_is_enabled: set CR4/N9 RED Enable to 1. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. Correct apidx from 0 to 0 for WscUUIDInit Generate UUID for apidx(0) UUID: c0634580, len = 16 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 b0 39 56 52 21 fd NOTIFY [SYSTEM]/sbin/brctl addif group1 rai0 interface rai0 does not exist! [SYSTEM]/bin/led_app on 40 Can't find DB for id==40 [SYSTEM]/bin/led_app on 42 [wlan/wifi.c::start_wireless():2625] no need fix f2 f3 value since this is 54M target power and NTGR need other value [libscm_wl.c::GenerateUUID():139] GUI ASCII string: 38833092-3092-1883-b892-b039565221fc [libscm_wl.c::GenerateUUID():140] GUI HEX string: 3883309230921883b892b039565221fc saved_index:0 [modelinfo_product_id.c::modelinfo_get_guest_led_replace_usb_led():281] guest_led_replace_usb_led is 0 [ has_8021x - 288 ] : 8021x none for band WIFI_BAND_2G [ has_8021x - 288 ] : 8021x none for band WIFI_BAND_5G [SYSTEM]/usr/bin/killall miniupnpd_wsc killall: miniupnpd_wsc: no process killed [SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh [SYSTEM]/bin/sh -x /var/ralink_ap_start.sh + iwpriv ra0 set WscConfMode=0 + iwpriv rai0 set WscConfMode=0 + iwpriv ra0 set WscSetupLock=0 + iwpriv rai0 set WscSetupLock=0 + iwpriv ra0 set WscMaxPinAttack=3 + iwpriv rai0 set WscMaxPinAttack=3 + route add -host 239.255.255.250 dev group1 + iwpriv ra0 set WscConfModRTMPIoctlMAC():after trim space, ptr len=8, pointer(8c8d5000)=82072218! e=7 + iwpriv rai0 set WscConfMode=7 + miniupnpd_wsc -m 1 -I raRTMPIoctlMAC():after trim space, ptr len=17, pointer(8c881000)=82072218=E8AFC240! 0 -P /var/run/miniupnpd.ra0 -i eth3 -a 192.168.1.1 -n 7777 -u 38RTMPIoctlMAC():after trim space, ptr len=8, pointer(8c905000)=82072218! 833092-3092-1883-b892-b039565221fc Unknown option: -I Unknown RTMPIoctlMAC():after trim space, ptr len=8, pointer(8c8d5000)=82072218! option: ra0 + sleep 10 + sleep 10 + + sleepsleep 10 7 + slRTMPIoctlMAC():after trim space, ptr len=17, pointer(8c881000)=82072218=E8AFC3A0! eep 10 [SYSTEM]/bin/cp /proc/uptime /tmp/wRTMPIoctlMAC():after trim space, ptr len=8, pointer(8c905000)=82072218! lan_uptime [SYSTEM]/bin/led_app on 44 [SYSTEM]/usr/sbin/led_app on 45 [wlan/wifi.c::need_disable_edcca():2371] wifiregion_in_gui:Europe [wlan/wifi.c::start_wireless():2753] ENABLE on EDCCA for 2G and 5G [wlan/wifi.c::start_wireleNOTIFY ss():2794] adjusNOTIFY t 5G RED ADAPTIVITY for EUROPE [SYSTEM]/usr/sbin/iwpriv raNOTIFY i0 mac 82072218OTIFY [0m rai0 mac:[0x12218]:e8afc3a0 [SYSTEM]/usr/sbin/NOTIFY iwpriv rai0 mac NOTIFY 82072218=E8AFC240 rai0 mac:[0x12218]:e8afc240 NOTIFY [SYSTEM]/usr/sbiNOTIFY n/iwpriv rai0 mac 82072218 rai0 mac:[0x12218]:e8afc240 [wlan/wifi.c::start_wireless():2799] need 2G edcca default threshold for region need RED ADAPTIVITY [SYSTEM]/usr/sbin/iwpriv ra0 mac 82072218 ra0 mac:[0x12218]:e8afc3a0 [SYSTEM]/usr/sbin/iwpriv ra0 mac 82072218=E8AFC3A0 ra0 mac:[0x12218]:e8afc3a0 [SYSTEM]/usr/sbin/iwpriv ra0 mac 82072218 ra0 mac:[0x12218]:e8afc3a0 [SYSTEM]/sbin/killall bndstrg killall: bndstrg: no process killed [SYSTEM]/sbin/bndstrg & [ start_wifi_service - 2870 ] : rc not ready, not enqueue the apcli_start rcd: [run] deQ =/usr/sbin/rc_app/rc_lan init [SYSTEM]/usr/sbin/brctl addbr group1 [SYSTEM]/sbin/ifconfig group1 up [SYSTEM]/usr/sbin/brctl addbr group2 [SYSTEM]/sbin/ifconfig group2 up rcd: [run] deQ =/usr/sbin/rc_app/rc_firewall init [00:00:45] [main]DebugLevel 2 [00:00:45] [main]Initialize bndstrg [00:00:45] [driver_wext_init]Initialize ralink wext interface [ firewall_main - 133 ] : before fw_exe [ firewall_main - 136 ] : end fw_exe iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. [00:00:46] [bndstrg_event_handle][bndstrg_event_handle][INF_STATUS_RSP_2G:ra0]0,1 iptables: No chain/target/match by that name. [00:00:46] [bndstrg_event_handle][bndstrg_event_handle][INF_STATUS_RSP_5G:rai0]0,1 iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. [00:00:47] [BndSSend DISASSOC Broadcast frame(3) with ra0 trg_status_polliBndStrg_Enable(): Band steering start running. ng]BndStrg_statuD_SetCndChkFlag(): CndChkFlag = 0x10f s_polling(): tabD_SetAgeTime(): AgeTime = 0 le->dbdc_mode=0,D_SetHoldTime(): HoldTime = 50 table->Band=0 [D_SetRssiLow(): RssiLow = -70 00:00:47] [BndStD_SetCheckTime(): CheckTime_2G = 30 rg_status_pollinSend DISASSOC Broadcast frame(3) with ra0 g]BndStrg_statusBndStrg_Enable(): Band steering start running. _polling(): bndsD_SetCndChkFlag(): CndChkFlag = 0x10f trg->table.b2GInD_SetAgeTime(): AgeTime = 0 fDiable_by_drv=0D_SetHoldTime(): HoldTime = 50 [00:00:47] [BnD_SetRssiLow(): RssiLow = -70 dStrg_status_polD_SetCheckTime(): CheckTime_5G = 30 ling]BndStrg_status_polling(): bndstrg->table.b5GInfDiable_by_drv=0 [00:00:47] [driver_wext_bndstrg_onoff]driver_wext_bndstrg_onoff [00:00:47] [driver_wext_bndstrg_onoff]driver_wext_bndstrg_onoff [00:00:48]onoff = 1,band = 2 [00:00:48] [bndstrg_event_on_off]bndstrg_event_on_off(): onoff = 1,band = 2 [00:00:48]SET_CHEK_CONDITIONS [00:00:48][bndstrg_set_priority] [00:00:48]onoff = 1,band = 1 [00:00:48] [bndstrg_event_on_off]bndstrg_event_on_off(): onoff = 1,band = 1 [00:00:48]SET_CHEK_CONDITIONS [00:00:48][bndstrg_set_priority] [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. rcd: [run] deQ =/usr/sbin/rc_app/rc_vlan start rcd: [run] deQ =/usr/sbin/rc_app/rc_funjsq start [ start_funjsq - 31 ] : not start funjsq in non-PR region or under ap mode/ bridge mode rcd: [run] deQ =/usr/sbin/rc_app/rc_lan start [../include/scvlan_shardevice eth2 entered promiscuous mode e.h::get_vlan_grgroup1: port 1(eth2) entering learning state oup():27] enablegroup1: port 1(eth2) entering learning state :1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [SYSTEM]/sbin/ifconfig eth2 updevice ra0 entered promiscuous mode [SYSTgroup1: port 2(ra0) entering learning state EM]/usr/sbin/brcgroup1: port 2(ra0) entering learning state tl addif group1 eth2 [SYSTEM]/sbin/ifconfig ra0 up [SYSTEM]/usr/sbin/brctl adevice rai0 entered promiscuous mode ddif group1 ra0roup1: port 3(rai0) entering learning state [0m [ start_langroup1: port 3(rai0) entering learning state _vlan_L2 - 901 ] : guest interface ra1 NOT enabled [SYSTEMNOTIFY ]/sbin/ifconfig rai0 up [SYSTEM]/usr/sbin/brctl addif group1 rai0 group1: port 3(rai0) entering learning statee rai1 NOT enabled [SYSTEM]/sgroup1: port 2(ra0) entering learning state bin/ifconfig grogroup1: port 1(eth2) entering learning state up1 down NOTIFY [SYSTEM]/sbin/ifconfig grouNOTIFY p1 up group1: port 3(rai0) entering learning state group1: port 3(rai0) entering learning state group1: port 2(ra0) entering learning state group1: port 2(ra0) entering learning state group1: port 1(eth2) entering learning state group1: port 1(eth2) entering learning state NOTIFY [SYSTEM]/usr/sbin/brctl setfd group1 1 [SYSTEM]/usr/sbin/brctl stp group1 off [ start_lan_vlan_L3 - 811 ] : index:1, wan:1 2 3 [SYSTEM]/sbin/ifconfig group1 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 [SYSTEM]/usr/sbin/ip route add to 192.168.1.0/24 dev group1 table 101 [SYSTEM]/usr/sbin/ip route add to blackhole default table 101 [SYSTEM]/usr/sbin/ip rule add from 192.168.1.1 table 101 [SYSTEM]/usr/sbin/ip rule add iif group1 table 101 [SYSTEM]/usr/sbin/ip rule add scmark 0x1 table 101 RTNETLINK answers: Invalid argument [SYSTEM]/usr/sbin/rc_app/rc_dhcpd start 1 [SYSTEM]killall udhcpd_1 killall: udhcpd_1: no process killed [SYSTEM]/bin/ln -sf /usr/sbin/udhcpd /var/udhcpd_1 [SYSTEM]/var/udhcpd_1 /etc/udhcpd.conf1 & [SYSTEM]/usr/sbin/rc_app/rc_firewall group 1 [ firewall_main - 133 ] : before fw_exe [ read_wanParams - 917 ] : end of read_wanParams on wan1 [dhcpd.c::udhcpd():116] udhcp server (v0.9.7) started [ read_wanParams - 917 ] : end of read_wanParams on wan1 [dhcpd.c::udhcpd():170] interface: group1, start : 201a8c0 end : fe01a8c0 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [SYSTEM]/usr/sbin/rc schedule restart rcd: enQ=/usr/sbin/rc_app/rc_schedule restart [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [SYSTEM]/usr/bin/killall -14 access_logd [SYSTEM]/bin/echo "enable_ipmac=0" > /proc/arp_protect_enable [ firewall_main - 136 ] : end fw_exe iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [SYSTEMNOTIFY ]/sbin/ifconfig eth2 up [SYSTEM]/usr/sbin/brctl addif group2 eth2 device eth2 is NOTIFY already a member of a bridge; can't enslave it tNOTIFY o bridge group2.NOTIFY [SYSTEM]/sbin/ifconfig group2 down [SYSTEM]/sbin/ifconfig group2 up [SYSTEM]/usr/sbin/brctl setfd group2 1 [SYSTEM]/usr/sbin/brctl stp group2 off [ start_lan_vlan_L3 - 811 ] : index:2, wan:1 2 3 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [SYSTEM]/sbin/ifconfig eth2 up [SYSTEM]/usr/sbin/brctl addif group3 eth2 interface eth2 does not exist! [SYSTEM]/sbin/ifconfig group3 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ifconfig group3 up ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/usr/sbin/brctl setfd group3 1 set forward delay failed: No such device [SYSTEM]/usr/sbin/brctl stp group3 off set stp status failed: No such device [ start_lan_vlan_L3 - 811 ] : index:3, wan:1 2 3 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [SYSTEM]/sbin/ifconfig eth2 up [SYSTEM]/usr/sbin/brctl addif group4 eth2 interface eth2 does not exist! [SYSTEM]/sbin/ifconfig group4 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ifconfig group4 up ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/usr/sbin/brctl setfd group4 1 set forward delay failed: No such device [SYSTEM]/usr/sbin/brctl stp group4 off set stp status failed: No such device [ start_lan_vlan_L3 - 811 ] : index:4, wan:1 2 3 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [SYSTEM]/sbin/ifconfig eth2 up [SYSTEM]/usr/sbin/brctl addif group5 eth2 interface eth2 does not exist! [SYSTEM]/sbin/ifconfig group5 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ifconfig group5 up ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/usr/sbin/brctl setfd group5 1 set forward delay failed: No such device [SYSTEM]/usr/sbin/brctl stp group5 off set stp status failed: No such device [ start_lan_vlan_L3 - 811 ] : index:5, wan:1 2 3 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [SYSTEM]/sbin/ifconfig eth2 up [SYSTEM]/usr/sbin/brctl addif group6 eth2 interface eth2 does not exist! [SYSTEM]/sbin/ifconfig group6 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ifconfig group6 up ifconfig: SIOCGIFFLAGS:ESW: Link Status Changed - Port3 Link Down No such device [SYSTEM]/usr/sbin/brctl setfd group6 1 set forward delay failed: No such device [SYSTEM]/usr/sbin/brctl stp group6 off set stp status failed: No such device [ start_lan_vlan_L3 - 811 ] : index:6, wan:1 2 3 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [SYSTEM]/sbin/ifconfig eth2 up [SYSTEM]/usr/sbin/brctl addif group7 eth2 interface eth2 does not exist! [SYSTEM]/sbin/ifconfig group7 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ifconfig group7 up ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/usr/sbin/brctl setfd group7 1 set forward delay failed: No such device [SYSTEM]/usr/sbin/brctl stp group7 off set stp status failed: No such device [ start_lan_vlan_L3 - 811 ] : index:7, wan:1 2 3 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [SYSTEM]/sbin/ifconfig eth2 up [SYSTEM]/usr/sbin/brctl addif group8 eth2 interface eth2 does not exist! [SYSTEM]/sbin/ifconfig group8 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ifconfig group8 up ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/usr/sbin/brctl setfd group8 1 set forward delay failed: No such device [SYSTEM]/usr/sbin/brctl stp group8 off set stp status failed: No such device [ start_lan_vlan_L3 - 811 ] : index:8, wan:1 2 3 rcd: [run] deQ =/usr/sbin/rc_app/rc_lan reset_switch down port 0 Set: phy[0].reg[0] = 1840 down port 1 Set: phy[1].reg[0] = 1840 down port 2 Set: phy[2].reg[0] = 1840 down port 3 Set: phy[3].reg[0] = 1840 + /sbin/iwpriv ra0 set BndStrgCndPD_SetCndChkFlag(): CndChkFlag = 0x1fa riority=1;3;5;6;7 [00:00:52][bndstrg_set_priority] + /sbin/iwpD_SetCheckTime(): CheckTime_2G = 10 D_SetCheckTime(): CheckTime_2G = 10 [00:00:52]SET_CHEK_CONDITIONS D_SetCheckTime(): CheckTime_5G = 10 + /sbin/iwpriv ra0 set BndStrgBsD_SetCheckTime(): CheckTime_5G = 10 sIdx=1 + /sbin/iwpriv rai0 set BndStrgBssIdx=1 + /sbin/iwpriv ra0 set BndStrg2GCheckTime=10 + /sbin/iwpriv rai0 set BndStrg2GCheckTime=10 + /sbin/iwpriv ra0 set BndStrg5GCheckTime=10 + /sbin/iwpriv rai0 set BndStrg5GCheckTime=10 up port 0 Set: phy[0].reg[0] = 1240 up port 1 Set: phy[1].reg[0] = 1240 up port 2 Set: phy[2].reg[0] = 1240 up port 3 Set: phy[3].reg[0] = 1240 rcd: [run] deQ =/usr/sbin/rc_app/rc_wifi_isolation start [SYSTEM]/bin/echo "lan_ip=192.168.1.1" > /proc/wifi_isolation /bin/sh: cannot create /proc/wifi_isolation: nonexistent directory [SYSTEM]/bin/echo "lan_netmask=255.255.255.0" > /proc/wifi_isolation /bin/sh: cannot create /proc/wifi_isonet/netfilter/nf_conntrack_sip.c: write_proc: file: 8d7331c0, buffer: 1 , count: 2, data: 00000000 lation: nonexistent directory [wifi_isolation/wifi_isolation.c::start_wifi_isolation():188] no ipv6 local ip [wifi_isolation/wifi_isolation.c::start_wifi_isolation():196] no ipv6 global ip rcd: [run] deQ =/usr/sbin/rc_app/rc_timezone start [SYSTEM]/bin/echo GMT+0 > /etc/TZ rcd: [run] deQ =/usr/sbin/rc_app/rc_sip_alg start [SYSTEM]/bin/echo 1 > /proc/sipalg_enable rcd: [run] deQ =/usr/sbin/rc_app/rc_mediaserver start #### media server is disable rcd: [run] deQ =/usr/sbin/rc_app/rc_dnrd start [ dnrd_main - 34 ] : do dnrd for 1 -> 1 [SYSTEM]iptables -t nat -D PREROUTING -i group1 -p tcp --dport 80 -j DNAT --to 192.168.1.1:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i group1 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i group1 -p udp --dport 53 -j DNAT --to 192.168.1.1 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -I PREROUTING -i group1 -d 66.114.62.22 -p tcp --dport 80 -j RETURN [SYSTEM]iptables -t nat -I PREROUTING -i group1 -d 66.114.62.29 -p tcp --dport 80 -j RETURN [SYSTEM]iptables -t nat -I PREROUTING -i group1 -d 174.35.24.133 -p tcp --dport 80 -j RETURN [SYSTEM]iptables -t nat -I PREROUTING -i group1 -d 101.96.10.64 -p tcp --dport 80 -j RETURN [SYSTEM]/bin/killall -9 dnrd_1 2>/dev/null [ start_dnrd - 115 ] : wan_account BOARD_ID same, wan_account no need in host file [SYSTEM]/bin/killall -9 dnrd_1 2>/dev/null [SYSTEM]/bin/ln -sf /usr/sbin/dnrd /var/dnrd_1 [SYSTEM]iptables -t nat -D PREROUTING -i group1 -p udp --dport 53 -j DNAT --to 192.168.1.1 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -I PREROUTING -i group1 -p udp --dport 53 -j DNAT --to 192.168.1.1 [SYSTEM]iptables -t nat -I PREROUTING -i group1 -p tcp --dport 80 -j DNAT --to 192.168.1.1:80 [SYSTEM]/var/dnrd_1 -a 192.168.1.1 -m hosts -c off -r 0 -g routerlogin.com & rcd: [run] deQ =/usr/sbin/rc_app/rc_debug_mode start killall: telnetenabled: no process killed escape_for_shell_by_backslash_in_doublequote: start_tlnconsoleblock str: password escape_for_shell_by_backslash_in_doublequote: start_tlnconsoleblock str: password [debug_mode/tln_cfg.c::start_tlnconsoleblock():75] cmd:telnetenabled 192.168.1.1 B039565221FC admin "password" & rcd: [run] deQ =/usr/sbin/rc_app/rc_httpd start Notice: caching turned off Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off. [sc_language.c::create_language_file():475] Create link files for <English> [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock4 to ENU [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock5 to CHS [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock6 to RUS [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock7 to DEU [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock8 to ESP [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock9 to NLD [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock10 to KOR [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock11 to FRA [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock12 to SVE [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock13 to CSY [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock14 to TUR [sc_language.c::update_language_mtd_mapping():368] update mtd /dev/mtdblock15 to ITA [sc_language.c::create_language_file():498] Checking MTD </dev/mtdblock4> according to its id <ENU> [sc_language.c::decompress_language():200] Try to decompress MTD </dev/mtdblock4> [watchdog.c::main():142] Watchdog: process 'syslogd' exists, score: 5. + brctl+ addifbrctl group1 addif rai0 group1 radevice ra1 entered promiscuous mode 0 device devicedevice ra1 left promiscuous mode ra0rai0 is alredevice rai1 entered promiscuous mode ady a member of device rai1 left promiscuous mode a bridge; can't device ra1 entered promiscuous mode enslave it to brdevice ra1 left promiscuous mode idge is alreadydevice rai1 entered promiscuous mode a member of a bdevice rai1 left promiscuous mode ridge; can't enslave it to bridge group1group1. . + + brctlbrctl addif addif group1 group1 rai1 ra1 can't add ra1 to bridge group1: Invalid argument can't add rai1 to bridge group1: Invalid argument [SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|R6800|g" > /etc/block.htm rmmod: ipt_REJECT: No such file or directory rcd: enQ=/usr/sbin/rc_app/rc_firewall restart [SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR R6800" -c '**.cgi' -t 300& rcd: [run] deQ =/usr/sbin/rc_app/rc_httpd remote start rcd: [run] deQ =/usr/sbin/rc_app/rc_printk start [SYSTEM]/bin/echo 1 4 1 7 > /proc/sys/kernel/printk rcd: [run] deQ =/usr/sbin/rc_app/rc_ntp start [SYSTEM]/usr/sbin/netgear_ntp -z GMT+0& rcd: [run] deQ =/usr/sbin/rc_app/rc_ddns init [ddns/ddns_cfg.c::ddns_init():489] +++ddns is disable, not need init++++ rcd: [run] deQ =/usr/sbin/rc_app/rc_wan init [ wan_main - 661 ] : rc wan enter [ read_wanParams - 917 ] : end of read_wanParams on wan1 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [ read_wanParams - 917 ] : end of read_wanParams on wan2 [ read_wanParams - 917 ] : end of read_wanParams on wan3 [SYSTEM]/bin/killall wan_monitor killall: wan_monitor: no process killed [SYSTEM]/bin/wan_monitor & [SYSTEM]/bin/mkdir /tmp/apcli [SYSTEM]/bin/touch /tmp/apcli/okrun rcd: [run] deQ =/usr/sbin/rc_app/rc_route start rcd: [run] deQ =/usr/sbin/rc_app/rc_ripd start rcd: [run] deQ =/usr/sbin/rc_app/rc_potcounter start killall: potcounter: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_lltd start [SYSTEM]/usr/bin/lld2 group1 rcd: [run] deQ =/usr/sbin/rc_app/rc_upnp start [SYSTEM]/usr/bin/killall miniupnpd killall: miniupnpd: no process killed [SYSTEM]route add -net 239.0.0.0 netmask 255.0.0.0 group1 [SYSTEM]/usr/sbin/miniupnpd -i eth3 -a 192.168.1.1 -p 56688 -U -t 1800 -T 4 -u 824ff22b-8c7d-41c5-a131-b039565221fc rcd: [run] deQ =/usr/sbin/rc_app/rc_schedule start [flash.c::sc_get_region():632] Original Region Data: 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab set crontab for wifi_schedule --- 0 [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule /bin/sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory rcd: [run] deQ =/usr/sbin/rc_app/rc_usb_service init SHARES_ALL: sd list: Disk X: volume_name=U Drive device_name=Flash Disk capacity=2432 serial_num=FBI1302250605342:2 type=FAT32 dev_node=xxx approved=0 Shere List:: Share Name=USB_Storage Folder=<root> R=1 W=1 Disk X: volume_name=Ubuntu-MATE 16.04.2 LTS amd64 device_name=Flash Disk capacity=1656480 serial_num=FBI1302250605342:1 type= dev_node=xxx approved=0 Shere List:: Share Name=T_Drive Folder=<root> R=1 W=1 list done. [SYSTEM]/usr/sbin/rc_app/rc_smb event reconfig [SYSTEM]echo LD_LIBRARY_PATH=$LD_LIBRARY_PATH LD_LIBRARY_PATH= [SYSTEM]echo LD_LIBRARY_PATH=$LD_LIBRARY_PATH LD_LIBRARY_PATH=/lib/private:/tmp/lib_in_ram [ smb_main - 64 ] : update samba_home_directory /home/eason/qqq/ [ smb_main - 75 ] : usb directory not ready, samba_home_directory:/home/eason/qqq/ [SYSTEM]mkdir -p /tmp/home_directory/ [SYSTEM]mkdir -p /home/eason/qqq//var/cores/ [wan_monitor.c::main():434] lan port change, get again [SYSTEM]chmod 0700 /home/eason/qqq//var/cores/ [SYSTEM]ln -sf /etc/ /home/eason/qqq//etc [SYSTEM]cd /etc/; cp -a samba.conf/ samba [SYSTEM]mkdir /home/eason/qqq//var/locks [SYSTEM]mkdir /home/eason/qqq//var/cache [SYSTEM]mkdir /home/eason/qqq//var/run [SYSTEM]mkdir -p /home/eason/qqq//private/ [SYSTEM]mkdir -p /tmp/lib_in_ram/ [SYSTEM]cp -af /lib/smblibforcp/* /tmp/lib_in_ram/ [wan_monitor.c::main():440] lan port change, get again [wan_monitor.c::main():580] call rc wan restart [SYSTEM]rc wan restart rcd: enQ=/usr/sbin/rc_app/rc_wan restart rcd: enQ=/usr/sbin/rc_app/rc_check_conn start [SYSTEM]cp -af /usr/sbin/smbd /tmp/lib_in_ram/ [SYSTEM]cp -af /usr/sbin/nmbd /tmp/lib_in_ram/ [SYSTEM]/etc/mtk/mt7621_smp.sh wifi smp.sh:dhcpc wifi eth2/eth3 RPS: CPU0/2 [SYSTEM]/bin/rm /etc/samba/secrets.tdb rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory [SYSTEM]/bin/rm /etc/secrets.tdb rm: cannot remove '/etc/secrets.tdb': No such file or directory [SYSTEM]/bin/rm /secrets.tdb rm: cannot remove '/secrets.tdb': No such file or directory [SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1 [SYSTEM]/usr/bin/killall -9 nmbd >/dev/null 2>&1 [SYSTEM]/usr/sbin/cp -f /etc/passwd.bak /etc/passwd [SYSTEM]/usr/sbin/rm -f /etc/samba/smbpasswd [SYSTEM]/usr/sbin/rc_app/rc_ftpd event mount [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [SYSTEM]/usr/bin/killall -9 bftpd bftpd_ipv6 >/dev/null 2>&1 [SYSTEM]/usr/sbin/rc_app/rc_apple event mount [SYSTEM]/usr/sbin/rc_app/rc_smb_http_en_chk event mount [ start_smb_http_en - 209 ] : entering [SYSTEM]/usr/sbin/rc_app/rc_mediaserver event mount [SYSTEM]killall -9 minidlna killall: minidlna: no process killed #### media server is disable [SYSTEM]/usr/sbin/rc_app/rc_iserver event mount [SYSTEM]/usr/bin/killall -9 forked-daapd killall: forked-daapd: no process killed [SYSTEM]/usr/sbin/rc_app/rc_down_manage event mount [down_manage/down_manage.c::start_download_manage():64] not enabled [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed [usb_service/usb.c::has_printer_at_port():660] check if device has printer at port 0 [modelinfo_product_id.c::modelinfo_map_index():123] 0x30 0x36, 0x3036. find index 0 for modelinfo_get_product_name [modelinfo_product_id.c::modelinfo_get_guest_led_replace_usb_led():281] guest_led_replace_usb_led is 0 [SYSTEM]/usr/sbin/led_app off 60 [usb_service/usb.c::has_printer_at_port():660] check if device has printer at port 1 saved_index:0 [modelinfo_product_id.c::modelinfo_get_guest_led_replace_usb_led():281] guest_led_replace_usb_led is 0 [SYSTEM]/usr/sbin/led_app off 61 rcd: [run] deQ =/usr/sbin/rc_app/rc_vlan start rcd: [run] deQ =/usr/sbin/rc_app/rc_dbus start [SYSTEM]/usr/sbin/dbus-daemon --config-file=/etc/dbus-1/system.conf rcd: [run] deQ =/usr/sbin/rc_app/rc_xCloud start [SYSTEM]/usr/bin/killall xCloud_monitor killall: xCloud_monitor: no process killed [SYSTEM]/usr/sbin/xCloud_monitor & rcd: [run] deQ =/usr/sbin/rc_app/rc_access_dev start Access Control socket create rcd: [run] deQ =/usr/sbin/rc_app/rc_accessctl_block restart [SYSTEM]/sbin/rmmod /lib/modules/accessctl_block.ko rmmod: /lib/modules/accessctl_block.ko: No such file or directory rcd: [run] deQ =/usr/sbin/rc_app/rc_openvpn prepare [openvpn.c::decompress_openvpn_cert_file():89] Try to decompress MTD </dev/mtdblock25> [openvpn.c::get_openvpn_info():68] md5=ebcb6bfb5591623c0c6c2b815dbf9c84,len=15079 [openvpn.c::decompress_openvpn_cert_file():136] md5 ok! WARNING: can't open config file: /usr/local/ssl/openssl.cnf [openvpn.c::openvpn_cert_file_verify():158] buf=/usr/sbin/openssl x509 -in /tmp/openvpn/keys/ca.crt -noout -issuer > /tmp/ca.txt WARNING: can't open config file: /usr/local/ssl/openssl.cnf [openvpn.c::openvpn_cert_file_verify():161] buf=/usr/sbin/openssl x509 -in /tmp/openvpn/keys/server.crt -noout -issuer > /tmp/server.txt WARNING: can't open config file: /usr/local/ssl/openssl.cnf [openvpn.c::openvpn_cert_file_verify():164] buf=/usr/sbin/openssl x509 -in /tmp/openvpn/keys/client.crt -noout -issuer > /tmp/client.txt [openvpn.c::openvpn_cert_file_verify():175] /tmp/ca.txt verify ok [openvpn.c::openvpn_cert_file_verify():175] /tmp/server.txt verify ok [openvpn.c::openvpn_cert_file_verify():175] /tmp/client.txt verify ok [openvpn.c::openvpn_cert_file_verify():187] verify ok! [SYSTEM]/usr/sbin/cp -af /tmp/openvpn/keys/* /tmp/openvpn/ [SYSTEM]/usr/sbin/rm -rf /tmp/openvpn/keys nvram commit! rcd: [run] deQ =/usr/sbin/rc_app/rc_usb_printer start [SYSTEM]/sbin/killall KC_BONJOUR killall: KC_BONJOUR: no process killed [SYSTEM]/sbin/killall KC_PRINT killall: KC_PRINT: no process killed [SYSTEM]/sbin/rmmod usblp rmmod: usblp: No such file or directory [SYSTEM]/sbin/rmmod NetUSB.ko rmmod: NetUSB.ko: No such file or directory [SYSTEM]/sbin/rmmod GPL_NetUSB.ko rmmod: GPL_NetUSB.ko: No such file or directory [modelinfo_product_id.c::modelinfo_map_index():123] 0x30 0x36, 0x3036. find index 0 for modelinfo_get_product_name [modelinfo_product_id.c::modelinfo_get_r7450series_customsized():314] r7450series_customsized is 0 [usb_printer/usb_printer.c::no_need_printer():38] no_need printer:0 [SYSTEM]/sbin/insmod /lib/modules/GPL_NetUSB.ko [SYSTEM]/sbin/insmod /lib/modules/NetUSB.ko localID="R6800" insmod: cannot insert '/lib/modules/NetUSB.ko': unknown symbol in module [SYSTEM]/sbin/insmod /lib/modules/NetUSB.ko [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/class/usblp.ko [usb_printer/usb_printer.c::no_need_printer():38] no_need printer:0 [SYSTEM]/sbin/KC_BONJOUR R6800 & [SYSTEM]/sbin/KC_PRINT R6800 & rcd: [run] deQ =/usr/sbin/rc_app/rc_wan apcli_rc_ready [Bonjour] Interface: group1 is connected [ wan_main - 661 ] : rc wan enter [SYSTEM]/bin/touch /tmp/apcli/rc_ready rcd: [run] deQ =/usr/sbin/rc_app/rc_check_conn start [KC] R6800 IPP v1.6 Start (May 24 2019 10:17:48) [ read_wanParams - 917 ] : end of read_wanParams on wan1 rcd: [run] deQ =/usr/sbin/rc_app/rc_RAE start [SYSTEM]/usr/sbin/RAE_update_monitor & rcd: [run] deQ =/usr/sbin/rc_app/rc_start finished [SYSTEM]/etc/mtk/mt7621_smp.sh wifi [RAE_update_monitor.c::main():814] RAE: Waiting WAN up... smp.sh:dhcpc wifi eth2/eth3 RPS: CPU0/2 [SYSTEM]/etc/enlarge_mem_reclaim_threshold.sh [SYSTEM]/usr/sbin/echo > /tmp/bootup_finished [start/start_cfg.c::bind_busydaemon_to_free_cpu():429] pid_multi_pb_app:456, pid_led_switch:301 pid_i2c_drv_thread:135 [SYSTEM]/sbin/taskset -p 4 456 pid 456's current affinity mask: (null) pid 456's new affinity mask: 4 [SYSTEM]/sbin/taskset -p 4 301 pid 301's current affinity mask: (null) pid 301's new affinity mask: 4 [SYSTEM]/sbin/taskset -p 4 135 pid 135's current affinity mask: (null) pid 135's new affinity mask: 4 [SYSTEM]/usr/sbin/generate_cert_file & [flash.c::sc_check_remotescfgmgrmagic():1357] buf:ff, ff, ff, ff [flash.c::sc_check_remotescfgmgrmagic():1359] magic:31, 3e, c5, 8d rcd: [run] deQ =/usr/sbin/rc_app/rc_usb_service led_update [usb_service/usb.c::has_printer_at_port():660] check if device has printer at port 0 [modelinfo_product_id.c::modelinfo_map_index():123] 0x30 0x36, 0x3036. find index 0 for modelinfo_get_product_name [modelinfo_product_id.c::modelinfo_get_guest_led_replace_usb_led():281] guest_led_replace_usb_led is 0 [SYSTEM]/usr/sbin/led_app off 60 [usb_service/usb.c::has_printer_at_port():660] check if device has printer at port 1 saved_index:0 [modelinfo_product_id.c::modelinfo_get_guest_led_replace_usb_led():281] guest_led_replace_usb_led is 0 [SYSTEM]/usr/sbin/led_app off 61 rcd: [run] deQ =/usr/sbin/rc_app/rc_schedule restart [flash.c::sc_get_region():632] Original Region Data: 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab set crontab for wifi_schedule --- 0 [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule /bin/sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory rcd: [run] deQ =/usr/sbin/rc_app/rc_firewall restart [ firewall_main - 133 ] : before fw_exe [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [SYSTEM]/usr/sbin/rc schedule restart rcd: enQ=/usr/sbin/rc_app/rc_schedule restart [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [SYSTEM]/usr/bin/killall -14 access_logd [SYSTEM]/bin/echo "enable_ipmac=0" > /proc/arp_protect_enable [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ fw_wan_L3 - 78 ] : wan1-ip0.0.0 enter [ read_wanParams - 917 ] : end of read_wanParams on wan2 [ fw_wan_L3 - 78 ] : wan2-ip0.0.0 enter [ read_wanParams - 917 ] : end of read_wanParams on wan3 [ fw_wan_L3 - 78 ] : wan3-ip0.0.0 enter [ firewall_main - 136 ] : end fw_exe WARNING: can't open config file: /usr/local/ssl/openssl.cnf [generate_cert_file.c::cert_file_build_time():107] cert current year=2019 WARNING: can't open config file: /usr/local/ssl/openssl.cnf [generate_cert_file.c::cert_signature_algorithm_deprecated():133] Signature Algorithm of OpenVPN cert is: sha256WithRSAEncryption [generate_cert_file.c::main():219] openvpn cert correct, no need update [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. [Bonjour] MDNS_CheckName: receive packet timeout [Bonjour] default device name = R6800 [Bonjour] Answer Name Start (192.168.1.1) [KC] R6800 Bonjour v1.5 Start (Aug 3 2016 15:06:52) iptables: Bad rule (does a matching rule exist in that chain?). iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. rcd: [run] deQ =/usr/sbin/rc_app/rc_wan restart [ wan_main - 661 ] : rc wan enter [ wan_action - 440 ] : entering wan0 InternetGatewayDevice.WANDevice.1.WANConnectionDevice. [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ wan_stop_con - 179 ] : entering wan1 [ipv6/common.c::ip6_config_dump():173] ignore dump ipv6 configconfig parser successfully . [ wan_stop_con - 195 ] : allWanL3 of TotalCon <> [ stop_L2 - 989 ] : entering wan1 [ wan_stop_con - 247 ] : stop l2 +++++++++++++++ [ read_wanParams - 917 ] : end of read_wanParams on wan2 [ wan_stop_con - 179 ] : entering wan2 [ wan_stop_con - 195 ] : allWanL3 of TotalCon <> [ stop_L2 - 989 ] : entering wan2 [ wan_stop_con - 247 ] : stop l2 +++++++++++++++ [ read_wanParams - 917 ] : end of read_wanParams on wan3 [ wan_stop_con - 179 ] : entering wan3 [ wan_stop_con - 195 ] : allWanL3 of TotalCon <> [ stop_L2 - 989 ] : entering wan3 [ wan_stop_con - 247 ] : stop l2 +++++++++++++++ [ wan_main - 983 ] : ======vpi=<0>,vci=<0>,enable=<0>,encap=<(null)> [ wan_main - 984 ] : mode=<(null)>,link_enable=<(null)>contype=<0> [ wan_action - 440 ] : entering wan0 InternetGatewayDevice.WANDevice.1.WANConnectionDevice. [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ wan_action - 455 ] : entering wan0 wan_start_con [ wan_start_con - 279 ] : entering wan1 [ is_wan_enable - 93 ] : wan 1 is enabled for ANNEXB [ start_L2 - 906 ] : entering <wan 1> Ethernet [ start_eth - 665 ] : entering start_eth [SYSTEM]/sbin/ifconfig eth3 up [SYSTEM]/sbin/ifconfig eth3 down [SYSTEM]/sbin/ifconfig eth3 hw ether B0:39:56:52:21:fe [SYSTEM]/sbin/ifconfig eth3 up [SYSTEM]/sbin/ifconfig eth3 mtu 1500 [SYSTEM]ifconfig eth3 up [ start_eth - 671 ] : L3IfName: eth3 [ wan_start_con - 313 ] : usb NOT mounted, update smp since need update the pptp [SYSTEM]/etc/mtk/mt7621_smp.sh wifi smp.sh:dhcpc wifi eth2/eth3 RPS: CPU0/2 [ start_ip - 135 ] : entering wan1 [SYSTEM]/bin/ln -sf /usr/sbin/udhcpc /var/w/udhcpc_1 [SYSTEM]/usr/sbin/rc_app/rc_firewall wan 1 init [ firewall_main - 133 ] : before fw_exe [ fw_new_wan_event - 31 ] : fw new event 4 [ read_wanParams - 917 ] : end of read_wanParams on wan1 [ fw_wan_L3 - 78 ] : wan1-ip0.0.0 enter [ firewall_main - 136 ] : end fw_exe [SYSTEM]/var/w/udhcpc_1 -i eth3 -s /etc/udhcpc.mpvc.script -w 1 -o /tmp/w/info_1 -H "R6800" -g 101& [ wan_start_con - 394 ] : ipv6 restart <disable> [ wan_start_con - 399 ] : ipv6 restart, v4 mode dhcpc v6 mode disable [SYSTEM]/usr/sbin/rc_app/rc_ipv6 restart [SYSTEM]/bin/echo 0 > /proc/sys/net/ipv6/conf/all/forwarding [dhcpc.c::udhcpc():419] udhcp client (v0.9.7) started [SYSTEM]/usr/bin/killall dhcp6c [clientpacket.c::random_xid():163] t:70, pid:7238 [clientpacket.c::send_discover():232] Sending discover...with xid 1111011764 killall: dhcp6c: no process killed [SYSTEM]/bin/killall pppd_ip6 killall: pppd_ip6: no process killed [SYSTEM]/usr/bin/killall radvd killall: radvd: no process killed [SYSTEM]/usr/bin/killall -9 dhcp6s killall: dhcp6s: no process killed [SYSTEM]/bin/killall -9 totd killall: totd: no process killed [SYSTEM]ip6tables -t filter -F [SYSTEM]ip6tables -t mangle -F [SYSTEM]ip6tables -t raw -F [SYSTEM]ip6tables -t filter -X [SYSTEM]ip6tables -t mangle -X [SYSTEM]ip6tables -t raw -X [SYSTEM]ip6tables -t filter -P INPUT ACCEPT [SYSTEM]ip6tables -t filter -P FORWARD ACCEPT [SYSTEM]ip6tables -C /tmp/rules6 ip6tables v1.4.10: option `-C' requires an argument Try `ip6tables -h' or 'ip6tables --help' for more information. [SYSTEM]killall mld killall: mld: no process killed [SYSTEM]/sbin/ip -6 route flush dev tun6to4 Cannot find device "tun6to4" [SYSTEM]/sbin/ip link set dev tun6to4 down Cannot find device "tun6to4" [SYSTEM]/sbin/ip tunnel del tun6to4 delete tunnel "tun6to4" failed: No such device [SYSTEM]/sbin/Ip -6 route flush dev tun6rd Cannot find device "tun6rd" [SYSTEM]/sbin/Ip link set dev tun6rd down Cannot find device "tun6rd" [SYSTEM]/sbin/Ip tunnel del tun6rd delete tunnel "tun6rd" failed: No such device [SYSTEM]/sbin/rmmod ipv6_br.ko rmmod: ipv6_br.ko: No such file or directory /bin/sh: /sbin/fc: not found [SYSTEM]/usr/bin/killall dhcp6c killall: dhcp6c: no process killed [SYSTEM]/usr/bin/killall ip6_autod killall: ip6_autod: no process killed [SYSTEM]/bin/rm -f /var/ip6prefix* [ipv6/ipv6.c::stop_ipv6():79] stop ip6 wan mode: (-1) [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv6/conf/all/disable_ipv6 [ipv6/common.c::ip6_config_dump():173] ignore dump ipv6 config[ipv6/ipv6.c::start_ipv6():176] IPV6IPV4PPP_ONE_SESSION not enable [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv6/conf/all/disable_ipv6 [SYSTEM]/bin/echo 2 > /proc/sys/net/ipv6/conf/all/forwarding [ start_ipv6 - 190 ] : ip6_config.wan_l2_ifname is eth3 [ipv6/ipv6.c::start_ipv6():203] ipv6 is over layer2, open rs/ra on eth3 [SYSTEM]/bin/echo 3 > /proc/sys/net/ipv6/conf/eth3/router_solicitations [SYSTEM]/bin/echo 2 > /proc/sys/net/ipv6/conf/eth3/accept_ra [ipv6/ipv6.c::start_ipv6():207] ipv6 is over layer2 interface eth3, trigger wan send out router solicitation [SYSTEM]/bin/echo trigger_rs=1 > /proc/net/trigger_rs [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/trigger_rs [ipv6/ipv6.c::start_ipv6():222] ip6 is disabled. [ipv6/common.c::ip6_config_free():503] ip6_6rdBRIP4Addr null [SYSTEM]/usr/sbin/rc wifi_isolation restart rcd: enQ=/usr/sbin/rc_app/rc_wifi_isolation restart [SYSTEM]/usr/sbin/rc_app/rc_hw_nat start [SYSTEM]/bin/echo 3 > /proc/sys/vm/drop_caches; /bin/insmod /lib/modules/`uname -r`/kernel/net/nat/hw_nat/hw_nat.ko [SYSTEM]/sbin/iwpriv ra0 set hw_nat_register=1 [SYSTEM]/sbin/iwpriv rai0 set hw_nat_register=1 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [../include/scvlan_share.h::get_vlan_group():27] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [ read_wanParams - 917 ] : end of read_wanParams on wan2 [ wan_action - 455 ] : entering wan0 wan_start_con [ wan_start_con - 279 ] : entering wan2 [ is_wan_enable - 88 ] : wan 2 is not enable [ wan_start_con - 289 ] : wan 2 is disabled [ read_wanParams - 917 ] : end of read_wanParams on wan3 [ wan_action - 455 ] : entering wan0 wan_start_con [ wan_start_con - 279 ] : entering wan3 [ is_wan_enable - 88 ] : wan 3 is not enable [ wan_start_con - 289 ] : wan 3 is disabled rcd: [run] deQ =/usr/sbin/rc_app/rc_check_conn start [ read_wanParams - 917 ] : end of read_wanParams on wan1 rcd: [run] deQ =/usr/sbin/rc_app/rc_schedule restart [flash.c::sc_get_region():632] Original Region Data: 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab set crontab for wifi_schedule --- 0 [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule /bin/sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory rcd: [run] deQ =/usr/sbin/rc_app/rc_wifi_isolation restart [SYSTEM]/sbin/rmmod /lib/modules/wifi_isolation.ko rmmod: /lib/modules/wifi_isolation.ko: No such file or directory [SYSTEM]/bin/echo "lan_ip=192.168.1.1" > /proc/wifi_isolation /bin/sh: cannot create /proc/wifi_isolation: nonexistent directory [SYSTEM]/bin/echo "lan_netmask=255.255.255.0" > /proc/wifi_isolation /bin/sh: cannot create /proc/wifi_isolation: nonexistent directory [wifi_isolation/wifi_isolation.c::start_wifi_isolation():188] no ipv6 local ip [wifi_isolation/wifi_isolation.c::start_wifi_isolation():196] no ipv6 global ip [clientpacket.c::send_discover():232] Sending discover...with xid 1111011764 [clientpacket.c::send_discover():232] Sending discover...with xid 1111011764 [kwilt_daemon.c::start_check_kwilt():680] kwilt wait for wan/usb/non-blank [script.c::run_script():451] ================== [script.c::run_script():453] interface=eth3 [script.c::run_script():453] PATH=/sbin:/bin:/usr/sbin:/usr/bin::/usr/local/sbin:/var/sbin [script.c::run_script():453] HOME=/ [script.c::run_script():453] w=1 [script.c::run_script():453] info=/tmp/w/info_1 [script.c::run_script():453] route_related_options_del_file=/tmp/dhcpc_route_related_options_del1 [script.c::run_script():454] ================== [script.c::run_script():458] execle'ing /etc/udhcpc.mpvc.script FAIL PATH=/sbin:/bin:/usr/sbin:/usr/bin::/usr/local/sbin:/var/sbin wan1: dhcpc FAIL [wan_monitor.c::main():434] lan port change, get again [clientpacket.c::send_discover():232] Sending discover...with xid 504644566 [clientpacket.c::send_discover():232] Sending discover...with xid 504644566 [clientpacket.c::send_discover():232] Sending discover...with xid 504644566 [kwilt_daemon.c::start_check_kwilt():680] kwilt wait for wan/usb/non-blank [script.c::run_script():451] ================== [script.c::run_script():453] interface=eth3 [script.c::run_script():453] PATH=/sbin:/bin:/usr/sbin:/usr/bin::/usr/local/sbin:/var/sbin [script.c::run_script():453] HOME=/ [script.c::run_script():453] w=1 [script.c::run_script():453] info=/tmp/w/info_1 [script.c::run_script():453] route_related_options_del_file=/tmp/dhcpc_route_related_options_del1 [script.c::run_script():454] ================== [script.c::run_script():458] execle'ing /etc/udhcpc.mpvc.script FAIL PATH=/sbin:/bin:/usr/sbin:/usr/bin::/usr/local/sbin:/var/sbin wan1: dhcpc FAIL [clientpacket.c::send_discover():232] Sending discover...with xid 1562767494 rcd: enQ=/usr/sbin/rc_app/rc_check_conn start rcd: [run] deQ =/usr/sbin/rc_app/rc_check_conn start [ read_wanParams - 917 ] : end of read_wanParams on wan1 [clientpacket.c::send_discover():232] Sending discover...with xid 1562767494 [clientpacket.c::send_discover():232] Sending discover...with xid 1562767494 [RAE_update_monitor.c::main():814] RAE: Waiting WAN up... [watchdog.c::main():142] Watchdog: process '/usr/sbin/mini_httpd' exists, score: 4.
OpenWrt bootlog
[ 0.000000] Linux version 4.14.172 (builder@buildhost) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12514-659ae99e9b)) #0 SMP Tue Mar 10 21:15:18 2020 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Netgear R6800 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] free_area_init_node: node 0, pgdat 80634800, node_mem_map 81003000 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x4e0 with crng_init=0 [ 0.000000] percpu: Embedded 14 pages/cpu s26096 r8192 d23056 u57344 [ 0.000000] pcpu-alloc: s26096 r8192 d23056 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00000e20 [ 0.000000] Readback ErrCtl register=00000e20 [ 0.000000] Memory: 251424K/262144K available (5011K kernel code, 256K rwdata, 1088K rodata, 1248K init, 260K bss, 10720K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.015500] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.087819] pid_max: default: 32768 minimum: 301 [ 0.097173] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.110194] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.126197] Hierarchical SRCU implementation. [ 0.135654] smp: Bringing up secondary CPUs ... [ 0.146235] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.146245] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.146256] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.146386] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.205009] Synchronize counters for CPU 1: done. [ 0.269592] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.269600] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.269608] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.269678] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.325680] Synchronize counters for CPU 2: done. [ 0.386905] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.386914] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.386924] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.386998] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.445244] Synchronize counters for CPU 3: done. [ 0.504844] smp: Brought up 1 node, 4 CPUs [ 0.517395] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.536884] futex hash table entries: 1024 (order: 3, 32768 bytes) [ 0.549420] pinctrl core: initialized pinctrl subsystem [ 0.561188] NET: Registered protocol family 16 [ 0.580096] FPU Affinity set after 11720 emulations [ 0.580942] pull PCIe RST: RALINK_RSTCTRL = 0 [ 0.889930] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.900000] ***** Xtal 40MHz ***** [ 0.906727] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.916936] Port 0 N_FTS = 1b105000 [ 0.923832] Port 1 N_FTS = 1b105000 [ 0.930756] Port 2 N_FTS = 1b102800 [ 2.089491] PCIE2 no card, disable it(RST&CLK) [ 2.098184] -> 21007f2 [ 2.103004] PCIE0 enabled [ 2.108200] PCIE1 enabled [ 2.113386] PCI host bridge /pcie@1e140000 ranges: [ 2.122911] MEM 0x0000000060000000..0x000000006fffffff [ 2.133279] IO 0x000000001e160000..0x000000001e16ffff [ 2.143631] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000 [ 2.167341] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 2.178669] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 2.189872] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 2.301465] i2c-mt7621 1e000900.i2c: clock 100KHz, re-start not support [ 2.315072] PCI host bridge to bus 0000:00 [ 2.323073] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 2.336749] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 2.348484] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 2.361962] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 2.377729] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 2.377768] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 2.377781] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff] [ 2.377843] pci 0000:00:00.0: supports D1 [ 2.377851] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 2.378096] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 2.378122] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 2.378135] pci 0000:00:01.0: reg 0x14: [mem 0x60210000-0x6021ffff] [ 2.378184] pci 0000:00:01.0: supports D1 [ 2.378192] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 2.378613] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 2.378662] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 2.378948] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.379158] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280 [ 2.379220] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 2.379540] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 2.379564] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02 [ 2.379653] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 2.392705] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.406501] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 2.419626] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.433455] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 2.446934] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] [ 2.460411] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] [ 2.473895] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] [ 2.487380] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 2.501892] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.511713] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 2.525220] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] [ 2.539735] pci 0000:00:01.0: PCI bridge to [bus 02] [ 2.549555] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] [ 2.564402] clocksource: Switched to clocksource GIC [ 2.575900] NET: Registered protocol family 2 [ 2.585229] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 2.598983] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 2.611764] TCP: Hash tables configured (established 2048 bind 2048) [ 2.624509] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.636007] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.648677] NET: Registered protocol family 1 [ 2.657265] PCI: CLS 0 bytes, default 32 [ 2.894346] 4 CPUs re-calibrate udelay(lpj = 2924544) [ 2.905892] Crashlog allocated RAM at address 0x3f00000 [ 2.916404] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 2.930686] random: fast init done [ 2.943157] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.954639] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.977501] io scheduler noop registered [ 2.985198] io scheduler deadline registered (default) [ 2.996430] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 3.012668] console [ttyS0] disabled [ 3.019758] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 3.037654] console [ttyS0] enabled [ 3.051440] bootconsole [early0] disabled [ 3.069825] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error [ 3.083865] Enable NFI Clock [ 3.089609] # MTK NAND # : Use HW ECC [ 3.096927] Device found in MTK table, ID: c2f1, EXT_ID: 809502 [ 3.108725] Support this Device in MTK table! c2f1 [ 3.118618] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 [ 3.131487] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 3.144134] nand: Macronix NAND 128MiB 3,3V 8-bit [ 3.153501] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 3.168591] Scanning device for bad blocks [ 3.413558] 7 fixed-partitions partitions found on MTD device MT7621-NAND [ 3.427078] Creating 7 MTD partitions on "MT7621-NAND": [ 3.437492] 0x000000000000-0x000000100000 : "u-boot" [ 3.448375] 0x000000100000-0x000000200000 : "SC PART_MAP" [ 3.460068] 0x000000200000-0x000000600000 : "kernel" [ 3.470893] 0x000000600000-0x000002e00000 : "ubi" [ 3.481506] 0x000002e00000-0x000004600000 : "reserved0" [ 3.493042] 0x000004600000-0x000004800000 : "factory" [ 3.504059] 0x000004800000-0x000008000000 : "reserved1" [ 3.515865] [mtk_nand] probe successfully! [ 3.524758] Signature matched and data read! [ 3.533240] load_fact_bbt success 1023 [ 3.541490] libphy: Fixed MDIO Bus: probed [ 3.616953] libphy: mdio: probed [ 5.024278] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver [ 5.036801] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 5.056181] NET: Registered protocol family 10 [ 5.066615] Segment Routing with IPv6 [ 5.073974] NET: Registered protocol family 17 [ 5.082949] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 5.108758] 8021q: 802.1Q VLAN Support v1.8 [ 5.120077] UBI: auto-attach mtd3 [ 5.126756] ubi0: attaching mtd3 [ 5.497997] ubi0: scanning is finished [ 5.520350] ubi0: attached mtd3 (name "ubi", size 40 MiB) [ 5.531119] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 5.544804] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 5.558311] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 5.572166] ubi0: good PEBs: 320, bad PEBs: 0, corrupted PEBs: 0 [ 5.584119] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 5.598498] ubi0: max/mean erase counter: 6/2, WL threshold: 4096, image sequence number: 1577527588 [ 5.616676] ubi0: available PEBs: 0, total reserved PEBs: 320, PEBs reserved for bad PEB handling: 20 [ 5.635053] ubi0: background thread "ubi_bgt0d" started, PID 397 [ 5.637053] block ubiblock0_0: created from ubi0:0(rootfs) [ 5.657996] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 5.671861] hctosys: unable to open rtc device (rtc0) [ 5.689252] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 5.707875] Freeing unused kernel memory: 1248K [ 5.716962] This architecture does not have kernel memory protection. [ 6.249205] init: Console is alive [ 6.256323] init: - watchdog - [ 6.918737] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 7.017049] usbcore: registered new interface driver usbfs [ 7.028100] usbcore: registered new interface driver hub [ 7.038845] usbcore: registered new device driver usb [ 7.057202] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator [ 7.074545] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator [ 7.092214] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 7.102826] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 7.124557] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010 [ 7.142834] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000 [ 7.155266] hub 1-0:1.0: USB hub found [ 7.162819] hub 1-0:1.0: 2 ports detected [ 7.171391] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 7.182006] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 7.196923] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 7.209939] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 7.226918] hub 2-0:1.0: USB hub found [ 7.234511] hub 2-0:1.0: 1 port detected [ 8.633957] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up [ 9.165235] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 9.194694] init: - preinit - [ 9.949496] mtk_soc_eth 1e100000.ethernet: PPE started [ 10.029352] random: procd: uninitialized urandom read (4 bytes read) [ 14.243557] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 524 [ 14.423742] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 14.439368] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 14.459124] UBIFS (ubi0:1): FS size: 33394688 bytes (31 MiB, 263 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs) [ 14.479904] UBIFS (ubi0:1): reserved for root: 1577313 bytes (1540 KiB) [ 14.493085] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID FF6B9027-FBBA-4041-B11F-6C2DD64EA240, small LPT model [ 14.517610] mount_root: overlay filesystem has not been fully initialized yet [ 14.532454] mount_root: switching to ubifs overlay [ 14.638606] urandom-seed: Seed file not found (/etc/urandom.seed) [ 14.728293] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818 [ 14.750662] procd: - early - [ 14.756546] procd: - watchdog - [ 15.444598] procd: - watchdog - [ 15.451181] procd: - ubus - [ 15.501268] random: ubusd: uninitialized urandom read (4 bytes read) [ 15.515081] random: ubusd: uninitialized urandom read (4 bytes read) [ 15.528111] random: ubusd: uninitialized urandom read (4 bytes read) [ 15.541640] procd: - init - [ 16.008149] kmodloader: loading kernel modules from /etc/modules.d/* [ 16.025978] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 16.045122] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc [ 16.060264] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51 [ 16.075458] ip_tables: (C) 2000-2006 Netfilter Core Team [ 16.093199] nf_conntrack version 0.5.0 (4096 buckets, 16384 max) [ 16.149191] xt_time: kernel timezone is -0000 [ 16.221030] bus=0x1, slot = 0x0, irq=0x0 [ 16.236835] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 16.239288] bus=0x2, slot = 0x1, irq=0x0 [ 16.240481] urngd: v1.0.2 started. [ 16.261667] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 16.269236] PPP generic driver version 2.4.2 [ 16.279691] NET: Registered protocol family 24 [ 16.291271] kmodloader: done loading kernel modules from /etc/modules.d/* [ 16.337739] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 16.337739] [ 16.337754] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 16.337754] [ 16.425558] random: crng init done [ 16.432360] random: 6 urandom warning(s) missed due to ratelimiting [ 16.587312] mt7615e 0000:02:00.0: N9 Firmware Version: 2.0, Build Time: 20200131181812 [ 16.587371] mt7615e 0000:01:00.0: N9 Firmware Version: 2.0, Build Time: 20200131181812 [ 16.659603] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 16.659669] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 23.669027] mtk_soc_eth 1e100000.ethernet: PPE started [ 23.684489] br-lan: port 1(eth0.1) entered blocking state [ 23.695484] br-lan: port 1(eth0.1) entered disabled state [ 23.706968] device eth0.1 entered promiscuous mode [ 23.716598] device eth0 entered promiscuous mode [ 23.728102] br-lan: port 1(eth0.1) entered blocking state [ 23.738909] br-lan: port 1(eth0.1) entered forwarding state [ 23.750405] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 24.684988] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 26.121211] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 26.140634] br-lan: port 2(wlan0) entered blocking state [ 26.151263] br-lan: port 2(wlan0) entered disabled state [ 26.162633] device wlan0 entered promiscuous mode [ 27.342789] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 27.355785] br-lan: port 2(wlan0) entered blocking state [ 27.366409] br-lan: port 2(wlan0) entered forwarding state