User Tools

Site Tools


toh:netgear:netgear_wac104

NETGEAR WAC104

Netgear WAC104

The Netgear WAC104 is a simultaneous dual band WIFI router with AC1200 WiFi - 300+867 Mbps (2.4 & 5 GHz) speeds. It contains non-removable external antennas. The AP features 4 Gbit LAN. It comes with a large 128 MB NAND ROM with space for many packages and a single core (dual thread) MIPS CPU (MT7621ST) powered by 128 MB RAM. The WAC104 is a castrated clone of R6220, with unsoldered WAN port and USB.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
WAC104MediaTek MT7621AT880128NAND256MediaTek MT7603EN, MediaTek MT7612ENb/g/na/n/ac-4--

Installation

Flash Layout

Netgear WAC104 Flash Layout
Layer0 NAND flash memory chip (Macronix 3,3V 8-bit SLC) 128 MiB
Layer1 mtd0 u-boot 1 MiB mtd1 SC PID 1 MiB mtd2 kernel 4 MiB mtd3 ubi 28 MiB unused 12 MiB mtd4 factory 1 MiB unused 19 MiB mtd5 reserved 60 MiB
mountpoint / /rom
filesystem OverlayFS SquashFS
Size in KiB 1024 KiB 1024 KiB 4096 KiB 3596 KiB 21204 KiB 12288 KiB 1024 KiB 19456 KiB 61440 KiB

OEM easy installation

Apply factory OpenWrt image via OEM web-gui.

Upgrading OpenWrt

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line.

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/openwrt-ramips-mt7621-netgear_wac104-squashfs-sysupgrade.bin
sysupgrade /tmp/openwrt-ramips-mt7621-netgear_wac104-squashfs-sysupgrade.bin

Debricking / Back to stock firmware

generic.debrick

Debricking of the WAC104 can be done by using the tool nmrpflash tool. See details over here: https://github.com/jclehner/nmrpflash

This tool can also be used to go back to stock firmware. For Windows users, ethernet cable must be connected to a switch or nmrpflash would fail to operate.

:!: This process only works with OEM firmware, don't try to flash OpenWrt images with nmrpflash.

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
lan1-lan4 LAN ports (1 to 4) None
wlan0 WiFi 2.4Ghz Disabled
wlan1 WiFi 5Ghz Disabled

Switch Ports (for VLANs)

In WAC104 is used DSA driver, so ports are visible as separate interfaces.

Port Switch port
LAN 1 LAN1
LAN 2 LAN2
LAN 3 LAN3
LAN 4 LAN4

LEDs

How to configure LEDs in general, see the LED section in the led_configuration.

The WAC104 has 7 LEDs:

LED name LED print Internal name Trigger Added information
Power Power wac104:green:power N/A .
WiFi Protected Setup WPS r6220:green:wps N/A User preference, for example, set your 5Ghz wifi traffic here
WiFi WiFi wac104:green:wifi phy0tpt phy0 is 2.4Ghz, phy1 is 5.0Ghz
LAN Port 1 LAN1 unknown N/A .
LAN Port 2 LAN2 unknown N/A .
LAN Port 3 LAN3 unknown N/A .
LAN Port 4 LAN4 unknown N/A .

Buttons

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The Netgear WAC104 has the following buttons:

Hotplug button name Action name
wps released/pressed
rfkill released/pressed
reset reset

Hardware

Info

General
Brand NETGEAR
Model WAC104
Versions
Device Type WiFi AP
Availability Available 2020
Comments - general This is castrated clone of R6220
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=221d8a1c6086ffd8bc53f81d5074a177d8dd8480
Supported Since Release
Supported Current Release snapshot
Unsupported
Hardware
Bootloader U-Boot
Target ramips
System-On-Chip
CPU MHz 880
Flash MB 128NAND
RAM MB 256
Network
Ethernet 100M ports -
Ethernet Gbit ports 4
Switch MediaTek MT7621ST
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware MediaTek MT7603EN, MediaTek MT7612EN
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports -
SATA ports -
Serial Yes
JTAG No
Comments - USB & SATA ports
Misc
LED count 3
Button count 3
Power supply 12 VDC, 1.5 A
Links
Forum Topic URL
WikiDevi URL https://wikidevi.wi-cat.ru/Netgear_WAC104
OEM device homepage URL https://www.netgear.com/business/products/wireless/essentials-wireless/WAC104.aspx
Firmware OEM Stock URL https://www.netgear.com/support/product/WAC104#download
Firmware OpenWrt Install URL http://¿
Firmware OpenWrt Upgrade URL http://¿
Edit the underlying data View/Edit data

Photos

Front:

Back:

Backside label:

Opening the case

Note: This will void your warranty!

The case is not held together using screws, only plastic latches. Use a prying tool to slowly pry the top part of the case away from the bottom. Remove a piece of tape covering the antenna wires and remove the antennas. Next, remove the screws holding the motherboard in place and slowly take it out of the case.

Main PCB:

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

J4 connector

Serial connection parameters
for NETGEAR WAC104
57600, 8N1 (J4 connector)

Bootloader mods

bootloader

None so far.

Hardware mods

None so far.

Bootlogs

OEM bootlog

=================================================================== MT7621 stage1 code 13:15:05 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0xd, 1/0 = 556/468 35000000 PLL2 FB_DL: 0x10, 1/0 = 688/336 41000000 PLL4 FB_DL: 0x13, 1/0 = 696/328 4D000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 16 rank 0 fine = 40 B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 opt_dle value:11 DRAMC_R0DELDLY[018]=00001F20 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 7 12 9 13 7 13 5 3 11 10 | 7 15 7 12 7 11 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =32 DQS1 = 31 ================================================================== bit DQS0 bit DQS1 0 (1~58)29 8 (1~55)28 1 (1~56)28 9 (1~56)28 2 (1~58)29 10 (2~60)31 3 (1~58)29 11 (2~58)30 4 (1~60)30 12 (1~59)30 5 (1~56)28 13 (1~56)28 6 (2~62)32 14 (1~58)29 7 (1~60)30 15 (2~58)30 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 15 11 15 12 15 11 13 7 6 14 10 | 7 15 8 15 9 12 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0801 DQS loop = 14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=14, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2 DQ loop=15, cmp_err_1 = ffff0080 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Sep 25 2015 - 10:29:47) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fac000 Config XHCI 40M PLL Allocate 16 byte aligned buffer: 87fe1bb0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 Env addr : 0x100000 .*** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.2.1.0 -------------------------------------------- ASIC MT7621AS (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Sep 25 2015 Time:10:29:47 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes Reset switch ... #Reset_MT7530 set LAN/WAN LLLLW ..Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, cmd 1, 0x0000000D cmd : 0x0000000D Press Ctrl+C to Enter the Main loop... Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, cmd 1, 0x0000000F cmd : 0x0000000F Enter NMRP_main Flash Sector Number : 1024. NetTxPacket = 0x87FE5B40 KSEG1ADDR(NetTxPacket) = 0xA7FE5B40 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done ETH_STATE_ACTIVE!! NMRP_FLASH_SIZE_buffer --> a1000000. NMRP:LISTENING ### No NMRP Server found ### KSEG1ADDR(NetTxPacket) = 0xA7FE5B40 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) ETH_STATE_ACTIVE!! STANDALONE_LOAD_ADDR is 0xa0600000 Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, boot Flash Sector Number : 1024. *************************************************** Sercomm Boot Version 1.19.0 *************************************************** Upgrade flag check pass!Entering Firmware : Everything is OK. kernel addr :0xbfe00000 System Boot system code via Flash. ## Booting image at bfe00000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2525365 Bytes = 2.4 MB Load Address: 80001000 Entry Point: 8000f500 ....................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK commandline in boot is : <NULL> !!!! No initrd ## Transferring control to Linux (at address 8000f500) ... ## Giving linux memsize in MB, 128 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Fri Sep 29 01:51:39 CST 2017 The CPU feqenuce set to 880 MHz GCMP present CPU revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 08000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000 avail: cpu2 is not ready avail: cpu3 is not ready Detected 1 available secondary CPU(s) PERCPU: Embedded 7 pages/cpu @81103000 s7104 r8192 d13376 u65536 pcpu-alloc: s7104 r8192 d13376 u65536 alloc=16*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 console=ttyS0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Writing ErrCtl register=0004f507 Readback ErrCtl register=0004f507 Memory: 122252k/131072k available (5385k kernel code, 8820k reserved, 1699k data, 216k init, 0k highmem) Hierarchical RCU implementation. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Trying to install interrupt handler for IRQ24 Trying to install interrupt handler for IRQ25 Trying to install interrupt handler for IRQ22 Trying to install interrupt handler for IRQ9 Trying to install interrupt handler for IRQ10 Trying to install interrupt handler for IRQ11 Trying to install interrupt handler for IRQ12 Trying to install interrupt handler for IRQ13 Trying to install interrupt handler for IRQ14 Trying to install interrupt handler for IRQ16 Trying to install interrupt handler for IRQ17 Trying to install interrupt handler for IRQ18 Trying to install interrupt handler for IRQ19 Trying to install interrupt handler for IRQ20 Trying to install interrupt handler for IRQ21 Trying to install interrupt handler for IRQ23 Trying to install interrupt handler for IRQ26 Trying to install interrupt handler for IRQ27 Trying to install interrupt handler for IRQ28 Trying to install interrupt handler for IRQ15 Trying to install interrupt handler for IRQ8 Trying to install interrupt handler for IRQ29 Trying to install interrupt handler for IRQ30 Trying to install interrupt handler for IRQ31 console [ttyS1] enabled Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Brought up 2 CPUs Synchronize counters across 2 CPUs: done. NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE1 no card, disable it(RST&CLK) pcie_link status = 0x5 RALINK_RSTCTRL= 5000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 12007f2 PCIE0 enabled PCIE2 enabled interrupt enable status: 500000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x60300000-0x6030ffff] (PCI address [0x60300000-0x6030ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] pci 0000:00:01.0: BAR 1: set to [mem 0x60310000-0x6031ffff] (PCI address [0x60310000-0x6031ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff] pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff] (PCI address [0x60200000-0x602fffff] pci 0000:00:01.0: PCI bridge to [bus 02-02] pci 0000:00:01.0: bridge window [io disabled] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] pci 0000:00:01.0: bridge window [mem pref disabled] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60300000 res[1]->end = 6030ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60310000 res[1]->end = 6031ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x19 res[0]->start = 60200000 res[0]->end = 602fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 128 (order: 0, 4096 bytes) UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1171456) squashfs: version 4.0 (2009/01/31) Phillip Lougher fuse init (API version 7.15) SGI XFS with security attributes, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem msgmni has been set to 238 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) Ralink gpio driver initialized spidrv_major = 217 i2cdrv_major = 218 spdif_mod_init: start SPDIF module Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A brd: module loaded MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 80753d20 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02, 00809502] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit) [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Scanning device for bad blocks Signature matched and data read! load_fact_bbt success 1023 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Creating 22 MTD partitions on "MT7621-NAND": 0x000000000000-0x000000100000 : "Bootloader" 0x000000100000-0x000000200000 : "SC PID" 0x000000200000-0x000000600000 : "Kernel" 0x000000600000-0x000002200000 : "Rootfs" 0x000002200000-0x000002400000 : "English UI" 0x000002400000-0x000002600000 : "ML1" 0x000002600000-0x000002800000 : "ML2" 0x000002800000-0x000002a00000 : "ML3" 0x000002a00000-0x000002c00000 : "ML4" 0x000002c00000-0x000002e00000 : "ML5" 0x000002e00000-0x000002f00000 : "Factory" 0x000002f00000-0x000003000000 : "SC Private Data" 0x000003000000-0x000003200000 : "POT" 0x000003200000-0x000003400000 : "Traffic Meter" 0x000003400000-0x000003600000 : "DPF" 0x000003600000-0x000003800000 : "SC Nvram" 0x000003800000-0x000003a00000 : "Ralink Nvram" 0x000003a00000-0x000003c00000 : "Ralink Reserved" 0x000003c00000-0x000003e00000 : "ML6" 0x000003e00000-0x000004000000 : "Upgrade Flag" 0x000004000000-0x000004200000 : "Reserved Block3" 0x000004200000-0x000007e00000 : "Reserved Block4" [mtk_nand] probe successfully! rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x4328804b Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288022 PROC INIT OK! PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 IMQ driver loaded successfully. Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. usbcore: registered new interface driver net1080 register mt_drv === pAd = c0182000, size = 703704 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0080000, csr_addr=0xc0080000! device_id =0x7603 RtmpChipOpsHook(502): Not support for HIF_MT yet! mt7603_init()--> mt_bcn_buf_init(224): Not support for HIF_MT yet! <--mt7603_init() FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1 xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Ralink APSoC Hardware Watchdog Timer Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1910 buckets, 7640 max) nf_conntrack_rtsp v0.6.21 loading IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. GRE over IPv4 demultiplexor driver gre: can't add protocol nf_nat_rtsp v0.6.21 loading ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 10 NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NOTIFY NOTIFY NOTIFY NOTIFY NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 L2TP IP encapsulation support (L2TPv3) L2TP netlink interface L2TP ethernet pseudowire support (L2TPv3) 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 216k freed init started: BusyBox v1.12.1 (2017-09-29 01:59:38 CST) starting pid 62, tty '': '/usr/etc/rcS' Algorithmics/MIPS FPU Emulator v1.5 mount: mounting none on /dev/pts failed: No such file or directory /usr/etc/rcS: /etc/PROJECT.mak: line 111: 3G_FEATURE=0: not found Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= [rc debug]/sbin/rc reg_init [rc.c::configure_mt7621_register():1037] set from jtag to gpio mode [SYSTEM]/sbin/reg switch register base addr to system register 0xbe000000 s 0 [SYSTEM]/sbin/reg r0xa05a9 0x60 [SYSTEM]/sbin/reg write offset 0x60, value 0xa05a8 w 0x60 0xa05a8 [SYSTEM]/sb0xa05a8 in/reg r 0x60 [SYSTEM]/bin/echo 1 > /NOTIFY prNOTIFY ocNOTIFY /NOTIFY sNOTIFY ysNOTIFY /NOTIFY net/ipv6/conf/all/disable_ipv6 led_pb_api: module license 'Sercomm' taints kernel. Disabling lock debugging due to kernel taint Register LED ID <75> Register LED ID <70> Register LED ID <45> Register LED ID <40> Register LED ID <20> Register LED ID <60> Register LED ID <61> Register LED ID <62> Register LED ID <90> Register LED ID <91> Register LED ID <92> insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/jbd2/jbd2.ko': No such file or directory insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/ext4/ext4.ko': No such file or directory netfilter dnshj choose interested dns queries module loaded ! insmod: can't read '/lib/modules/ipt_macblock_dnshj.ko': No such file or directory init common module successful insert firewall block module success fake source dos protect modules is inserted netfilter PSD and TCP/UDP Echo/Chargen Attack loaded netfilter tcp syn flood module loaded netfilter clamp total session for one src ip module loaded netfilter other dos module loaded insmod finish NOTIFY NOTIFY NOTIFY Raeth v3.1 (Tasklet,SkbRecycle) phy_tx_ring = 0x06e92000, tx_ring = 0xa6e92000 phy_rx_ring0 = 0x06e94000, rx_ring0 = 0xa6e94000 change HW-TRAP to 0x15c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288022 GDMA2_MAC_ADRH -- : 0x0000000c GDMA2_MAC_ADRL -- : 0x43288028 NOTIFY NOTIFY eth3: ===> VirtualIF_open CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 NOTIFY NOTIFY NOTIFY insmod: can't read '/lib/modules/2.6.36/kernel/drivers/net/wireless/MT7610_ap/MT7610_ap.ko': No such file or directory register rt2860 === pAd = c0982000, size = 1142784 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0880000, csr_addr=0xc0880000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a ====> mt76x2_ePA_per_rate_compensate_init: 5118 is_ePA: 1 RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is FLASH mode NOTIFY NOTIFY [rc debug]/usr/sbin/rc init [SYSTEM]/sbin/ifNOTIFY cNOTIFY onNOTIFY fig br0 down hw ether 14:59:C0:C3:DF:88 up [SYSTEM]/sbin/ifconfig eth2.1 down ifconfig: SIOCGIFFLAGS: No such deNOTIFY vice [SYSTEM]/sbin/ifconfig eth2.2 down ifconfig: SIOCGIFFLAGS: No suchra2880stop()... Done deeth3: ===> VirtualIF_close Free TX/RX Ring Memory! OTIFY 32m[SYSTEM]/sbin/ifconfig eth2 down [SYSTEM]/sbin/vconfig rem eth2.1 vconfig: ioctl error for rem: No such device [SYSTENOTIFY MRaeth v3.1 (]Tasklet/,SkbRecycles) bin phy_tx_ring = 0x0665e000, tx_ring = 0xa665e000 /vconfi phy_rx_ring0 = 0x06654000, rx_ring0 = 0xa6654000 g rem eth2.2 vconfig: ioctl error for rem: No such device [change HW-TRAP to 0x15c8f SYSTEM]/sbinset LAN/WAN LLLLW MAC1_MAC_ADRH -- : 0x0000000c 0GMAC1_MAC_ADRL -- : 0x43288022 eth3: ===> VirtualIF_open CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 NOTIFY [SYSTEM]/sbin/ifconfigNOTIFY eth2 down ra2880stop()...Done eth3: ===> VirtualIF_close Free TX/RX Ring Memory! NOTIFY [SYSTEM]/sbin/ifconfigNOTIFY NOTIFYhw ether 14:59:C0:C3:DF:88 asklet3,SkbRecycle2) m[S phy_tx_ring = 0x06f5a000, tx_ring = 0xa6f5a000 YSTEM]/ phy_rx_ring0 = 0x06f5c000, rx_ring0 = 0xa6f5c000 sbin/ifconfig eth2 up change HW-TRAP to 0x15c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x00001459 GMAC1_MAC_ADRL -- : 0xc0c3df88 eth3: ===> VirtualIF_open CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 NOTIFY [SYSTEM]/usr/sbin/config-vlan.sh 3 0 restore GSW to dump switch mode switch reg write offset=2004, value=ff0000 switch reg write offset=2104, value=ff0000 switch reg write offset=2204, value=ff0000 switch reg write offset=2304, value=ff0000 switch reg write offset=2404, value=ff0000 switch reg write offset=2504, value=ff0000 switch reg write offset=260device eth2 entered promiscuous mode 4,br0: port 1(eth2) entering learning state vbr0: port 1(eth2) entering learning state alue=ff0000 switch reg write offsetNOTIFY =eth3: ===> VirtualIF_open 27NOTIFY 04, value=ff0000 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=810000c0 switch reg write offset=2710, value=810000c0 REG_ESW_WT_MAC_ATC is 0x7ff0002 done. [SYSTEM]/sbin/brctl addif br0 eth2 [SYSTEM]/sbin/ifconfig eth3 up [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [rc.c::rc_init():489] region valid RC: wifi_init() rules = <>, timeout = 20 [SYSTEM]/usr/bin/killall access_logd killall: access_logd: no process killed [SYSTEM]/usr/sbin/rc access_log start [rc debug]/usr/sbin/rc access_log start ap_name=access_log action=start [rc.c::rc_action():829] rc_action before add access_log - start rc action <access_log @ start> before file_lock. rc action <access_log @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add access_log - start unlink running file </var/run/rc.access_log.run> [rc.c::rc_action():829] rc_action before add access_log - start rc action <access_log @ start> before file_lock. rc action <access_log @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add access_log - start unlink running file </var/run/rc.access_log.run> can't find this application [rc.c::rc_action():829] rc_action before add access_log - start rc action <access_log @ start> before file_lock. rc action <access_log @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add access_log - start [rc.c::rc_start():732] Calling Start function of access_log killall: access_logd: no process killed Access Control log start. Access Control socket create unlink running file </var/run/rc.access_log.run> [SYSTEM]/usr/sbin/rc access_dev start [rc debug]/usr/sbin/rc access_dev start ap_name=access_dev action=start [rc.c::rc_action():829] rc_action before add access_dev - start rc action <access_dev @ start> before file_lock. rc action <access_dev @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add access_dev - start unlink running file </var/run/rc.access_dev.run> [rc.c::rc_action():829] rc_action before add access_dev - start rc action <access_dev @ start> before file_lock. rc action <access_dev @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add access_dev - start unlink running file </var/run/rc.access_dev.run> can't find this application [rc.c::rc_action():829] rc_action before add access_dev - start rc action <access_dev @ start> before file_lock. rc action <access_dev @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add access_dev - start [rc.c::rc_start():732] Calling Start function of access_dev killall: access_devinfo: no process killed Access Control socket create unlink running file </var/run/rc.access_dev.run> [modelinfo_product_id.c::modelinfo_map_index():76] 0xff 0xff, 0xffff. [modelinfo_product_id.c::modelinfo_map_index():104] default map index to WAC104, flash type is nand [modelinfo_product_id.c::modelinfo_map_index():109] find index 0 for modelinfo_get_product_name [modelinfo_product_id.c::modelinfo_set_autoupg_fileinfo():182] autoupg_fileinfo_in_nv is wac104_fileinfo.txt [SYSTEM]/usr/bin/insmod /lib/modules/ufsd.ko ufsd:: trace mask set to 0000000f ufsd: driver (lke_9.0.0 lke_9.0.0_r237695_b2, LBD=ON, ioctl, bdi, sd2(0), wb, bz, tr) loaded at c0b4f000 NTFS support included optimized: speed Build_for__Netgear_R6220_k2.6.36_2014-10-22_lke_9.0.0_r237695_b2 =============rc start [rc debug]/usr/sbin/rc rwfs start ap_name=rwfs action=start [rc.c::rc_action():829] rc_action before add rwfs - start rc action <rwfs @ start> before file_lock. rc action <rwfs @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.rwfs.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add rwfs - start unlink running file </var/run/rc.rwfs.run> [rc.c::rc_action():829] rc_action before add rwfs - start rc action <rwfs @ start> before file_lock. rc action <rwfs @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.rwfs.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add rwfs - start unlink running file </var/run/rc.rwfs.run> can't find this application [rc.c::rc_action():829] rc_action before add rwfs - start rc action <rwfs @ start> before file_lock. rc action <rwfs @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.rwfs.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add rwfs - start unlink running file </var/run/rc.rwfs.run> can't find this application [rc debug]/usr/sbin/rc lan start ap_name=lan action=start [rc.c::rc_action():829] rc_action before add lan - start rc action <lan @ start> before file_lock. rc action <lan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.lan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add lan - start [rc.c::rc_start():732] Calling Start function of lan [SYSTEM]/usr/sbin/brctl setfd br0 1 [SYSTEM]/sbin/ifconfig br0 192.168.0.100 netmask 255.255.255.0 broadcast 192.168.0.255 [SYSTEM]/usr/sbin/brctl stp br0 off [SYSTEM]/usr/sbin/brctl stp br0 on sh: cannot create /proc/http_file/getLanIp: nonexistent directory unlink running file </var/run/rc.lan.run> [rc debug]/usr/sbin/rc wlan start ap_name=wlan action=start [rc.c::rc_action():829] rc_action before add wlan - start rc action <wlan @ start> before file_lock. rc action <wlan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.wlan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add wlan - start [rc.c::rc_start():732] Calling Start function of wlan [wifi_mtk/wifi.c::sync_wireless_nvram():1567] wifi_super_wifi_enable:0, wifi_powerpercent:100, wifi_super_wifi_enable1:0, wifi_powerpercent1:100 [flash.c::sc_check_remotescfgmgrmagic():795] buf:ff, ff, ff, ff [flash.c::sc_check_remotescfgmgrmagic():797] magic:31, 3e, c5, 8d [modelinfo_product_id.c::modelinfo_map_index():76] 0xff 0xff, 0xffff. [modelinfo_product_id.c::modelinfo_map_index():104] default map index to WAC104, flash type is nand [modelinfo_product_id.c::modelinfo_map_index():109] find index 0 for modelinfo_get_product_name [wifi_mtk/wifi.c::start_wireless():1626] SC 5G support level: 11ac [SYSTEM]mkdir -p /etc/Wireless/RT2860 scfgmgr for local [SYSTEM]mkdir -p /etc/Wireless/iNIC region flag in flash:00 00 00 02 [SYSTEM]/bin/mkdir -p /etc/Wireless/RT2860AP/ [SYSTEM]/bin/mkdir -p /etc_ro/Wireless/RT2860AP/ region is PR:0 [SYSTEM]/bin/cp -f /etc_ro/wlan/MT7612E_EEPROM.bin.11ac /etc_ro/wlan/MT7612E_EEPROM.bin [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [wifi_mtk/wifi.c::map_singleskutmp_by_region():1310] all region singlesku.dat exist [SYSTEM]/bin/rm /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 >/dev/console 2>&1 rm: cannot remove '/etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620': No such file or directory [SYSTEM]/bin/rm /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E >/dev/console 2>&1 rm: cannot remove '/etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E': No such file or directory [wifi_mtk/wifi.c::map_singleskutmp_by_region():1327] wifi gui region is Europe, 2g CE, 5g CE [wifi_mtk/wifi.c::map_singleskutmp_by_region():1376] region NOT PR or RU [SYSTEM]/bin/cp -rf /usr/etc_ro/Wireless/singlesku_dat//CE/SingSku-2.4.txt /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 >/dev/console 2>&1 [SYSTEM]/bin/cp -rf /usr/etc_ro/Wireless/singlesku_dat//CE/SingSku-5G.txt /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E >/dev/console 2>&1 [SYSTEM]/bin/rm -rf /etc/Wireless/RT2860AP/SingleSKU.dat [SYSTEM]/bin/mv /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 /etc/Wireless/RT2860AP/SingleSKU.dat [SYSTEM]/bin/rm -rf /etc_ro/Wireless/iNIC/SingleSKU.dat [SYSTEM]/bin/mv /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E /etc_ro/Wireless/iNIC/SingleSKU.dat CHIP: 7603 - current MAC: 14:59:C0:C3:DF:88 Assign MAC: 14:59:C0:C3:DF:88 no update! CHIP: 7662 - current MAC: 14:59:C0:C3:DF:8C Assign MAC: 14:59:C0:c3:df:8c no update! [SYSTEM]/sbin/iwpriv rai0 set RadioOn=1 Interface doesn't accept private ioctl... set (8BE2): Network is down X_BCN DESC a7fd1000 size = 320_setNOTIFY RX[0] DESC a7fdb000 size = 2048 [SYSTEM]RX[1] DESC a7fdc000 size = 2048 /sbin/ifconfig ra0 up cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 20140814CmdAddressLenReq:(ret = 0) CmdFwStartReq: override = 1, address = 1048576 CmdStartDLRsp: WiFI FW Download Success AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC) CmdPsRetrieveRsp Disable FW PS Supportstatus:1 !!!!! RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 efuse_probe: efuse = 10000002 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode 1. Phy Mode = 14 @@@ NICReadEEPROMParameters : pAd->FWLoad=0 Country Region from e2p = ffff tssi_1_target_pwr_g_band = 35 2. Phy Mode = 14 3. Phy Mode = 14 NICInitPwrPinCfg(13): Not support for HIF_MT yet! NICInitializeAsic(586): Not support rtmp_mac_sys_reset () for HIF_MT yet! mt_mac_init()--> mt7603_init_mac_cr()--> AsicSetMacMaxLen(1574): Set the Max RxPktLen=1024! <--mt_mac_init() WTBL Segment 1 info: MemBaseAddr/FID:0x28000/0 EntrySize/Cnt:32/128 WTBL Segment 2 info: MemBaseAddr/FID:0x40000/0 EntrySize/Cnt:64/128 WTBL Segment 3 info: MemBaseAddr/FID:0x42000/64 EntrySize/Cnt:64/128 WTBL Segment 4 info: MemBaseAddr/FID:0x44000/128 EntrySize/Cnt:32/128 AntCfgInit(2384): Not support for HIF_MT yet! AsicSendCommandToMcu(3423): Not support for HIF_MT yet! AsicSendCommandToMcu(3423): Not support for HIF_MT yet! AsicSendCommandToMcu(3423): Not support for HIF_MT yet! AsicSendCommandToMcu(3423): Not support for HIF_MT yet! RTMPSetPhyMode(): channel out of range, use first ch=0 MCS Set = ff ff 00 00 01 AsicSetChBusyStat(889): Not support for HIF_MT yet! CmdChannelSwitch: control_chl = 1, central_chl = 1, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 2, central_chl = 2, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 3, central_chl = 3, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 4, central_chl = 4, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 5, central_chl = 5, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 6, central_chl = 6, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 7, central_chl = 7, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 8, central_chl = 8, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 9, central_chl = 9, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#9(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 10, central_chl = 10, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#10(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 11, central_chl = 11, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#11(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 12, central_chl = 12, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#12(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 13, central_chl = 13, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#13(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 1, central_chl = 1, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 2, central_chl = 2, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 3, central_chl = 3, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 4, central_chl = 4, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 5, central_chl = 5, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 6, central_chl = 6, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 7, central_chl = 7, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 8, central_chl = 8, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 [PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0 [PMF]ap_pmf_init:: apidx=2, MFPC=0, MFPR=0, SHA256=0 [PMF]ap_pmf_init:: apidx=3, MFPC=0, MFPR=0, SHA256=0 AsicSetRalinkBurstMode(3737): Not support for HIF_MT yet! RTMPSetPiggyBack(809): Not support for HIF_MT yet! CmdChannelSwitch: control_chl = 1, central_chl = 3, BW = 1, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=1 AsicSetTxPreamble(3723): Not support for HIF_MT yet! AsicAddSharedKeyEntry(1738): Not support for HIF_MT yet! AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0 Main bssid = 14:59:c0:c3:df:88 <==== rt28xx_init, Status=0 NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY [SYSTEM]/usr/sbin/iwpriv ra0 set IgmpAdd=224.0.0.251 [SYSdevice ra0 entered promiscuous mode TEbr0: port 2(ra0) entering listening state M]br0: port 2(ra0) entering listening state /sbin/brctl addif br0 ra0 [SYSTEM]/bin/led_app on 40 [SYSTEM]/sbNOTIFY inbuild time = /i2f0c1o4n0f4i0g80 6r0a6i400 au prom patch for E3 IC latform = SALmP hw/sw version = ▒▒ patch version = FW Version:0.0.00 Build:1 Build Time:201411280941____ fw for E3 IC RX[0] DESC a6f05000 size = 4096 RX[1] DESC a6f06000 size = 4096 E2pAccessMode=2 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 49 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) br0: port 2(ra0) entering learning state get_chl_grp:illegal channel (173) get_chl_grp:illegal channel (173) Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=13, low_temp_slope=9 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c 2. Phy Mode = 49 3. Phy Mode = 49 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438 mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438 mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438 br0: topology change detected, propagating br0: port 2(ra0) entering forwarding state mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438 br0: topology change detected, propagating br0: port 1(eth2) entering forwarding state mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 mt76x2_single_sku::DefaultTargetPwr = 0x28, delta_power = 0xfe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x28, ch_pwr_adj = 0xfffffff8(-8), 0x13B4: 0x1b0f0438 APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) mt76x2_calibration(channel = 42) Main bssid = 14:59:c0:c3:df:8c mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48 mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48 mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33 original vga value(chain0) = 48 original vga value(chain1) = 48 <==== rt28xx_init, Status=0 NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! NOTIFY [SYSTEM]/sbin/brctl addevice rai0 entered promiscuous mode dibr0: port 3(rai0) entering listening state f br0: port 3(rai0) entering listening state br0 rai0 [SYSTEM]/bin/led_app on 40 [libscm_wl.c::GenerateUUID():121] GUI ASCII string: 38833092-3092-1883-92dd-1459c0c3df88 [libscm_wl.c::GenerateUUID():122] GUI HEX string: 388330923092188392dd1459c0c3df88 [SYSTEM]/usr/bin/killall miniupnpd_wsc killall: miniupnpd_wsc: no process killed [SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh [SYSTEM]/bin/sh -x /var/ralink_ap_start.sh + iwpriv ra0 set WscConfMode=0 + iwpriv rai0 set WscConfMode=0 + iwpriv ra0 set WscSetupLock=0 + iwpriv rai0 set WscSetupLock=0 + iwpriv ra0 set WscMaxPinAttack=3 + iwpriv rai0 set WscMaxPinAttack=3 + route add -host 239.255.255.250 dev br0 + iwpriv ra0 set WscConfMode=7 + iwpriv rai0 set WscConfMode=7 + miniupnpd_wsc -m 1 -I ra0 -P /var/runCan't find DB for id==42 /miniupnpd.ra0 -i eth3 -a 192.168.0.100 -n 7777 -u 38833092-3092-1883-92dd-1459c0c3df88 Unknown option: -I Unknown option: ra0 Jan 1 00:00:25 miniupnpd[337]: WPS listening on port 7777 [SYSTEM]/bin/cp /pRTMPIoctlMAC():wrq->u.data.length=9, pointer(7fd5e6b0)=60200618! roRTMPIoctlMAC():after trim space, ptr len=8, pointer(85e27000)=60200618! c/uptime /tmp/wlan_uptime [SYSTEM]/RTMPIoctlMAC():wrq->u.data.length=18, pointer(7feb6e70)=60200618=D7E87D10! binRTMPIoctlMAC():after trim space, ptr len=17, pointer(85e33000)=60200618=D7E87D10! /led_app on 42 [SYSTEM]/usr/sbin/leRTMPIoctlMAC():wrq->u.data.length=9, pointer(7fdbe100)=60200618! d_RTMPIoctlMAC():after trim space, ptr len=8, pointer(85e27000)=60200618! app off 45 [wifi_mtk/wifi.c::need_disable_edcca():1577] wifiregion_in_gui:Europe [wifi_mtk/wifi.c::start_wireless():1773] ENABLE on EDCCA for 2G and 5G [SYSTEM]/usr/sbin/iwpriv rai0 mac 1340 rai0 mac: [0x1340]:04101b3f [wifi_mtk/wifi.c::start_wireless():1793] org:0x4101b3f. (04101b3f )[wifi_mtk/wifi.c::start_wireless():1795] now:0x4101b3f [SYSTEM]/usr/sbin/iwpriv rai0 mac 1340=4101b3f rai0 mac: [0x1340]:04101b3f [SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618 ra0 mac:[0x10618]:d7e87d10 [SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618=D7E87D10 ra0 mac:[0x10618]:d7e87d10 [SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618 ra0 mac:[0x10618]:d7e87d10 unlink running file </var/run/rc.wlan.run> [rc debug]/usr/sbin/rc printk start ap_name=printk action=start [rc.c::rc_action():829] rc_action before add printk - start rc action <printk @ start> before file_lock. rc action <printk @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.printk.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add printk - start [rc.c::rc_start():732] Calling Start function of printk [SYSTEM]/bin/echo 1 4 1 7 > /proc/sys/kernel/printk unlink running file </var/run/rc.printk.run> [rc debug]/usr/sbin/rc timezone start ap_name=timezone action=start [rc.c::rc_action():829] rc_action before add timezone - start rc action <timezone @ start> before file_lock. rc action <timezone @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.timezone.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add timezone - start [rc.c::rc_start():732] Calling Start function of timezone [SYSTEM]/bin/echo GMT+0 > /etc/TZ unlink running file </var/run/rc.timezone.run> [rc debug]/usr/sbin/rc syslogd start ap_name=syslogd action=start [rc.c::rc_action():829] rc_action before add syslogd - start rc action <syslogd @ start> before file_lock. rc action <syslogd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add syslogd - start [rc.c::rc_start():732] Calling Start function of syslogd [SYSTEM]/sbin/syslogd -f /etc/syslog.conf unlink running file </var/run/rc.syslogd.run> [rc debug]/usr/sbin/rc httpd start ap_name=httpd action=start [rc.c::rc_action():829] rc_action before add httpd - start rc action <httpd @ start> before file_lock. rc action <httpd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add httpd - start [rc.c::rc_start():732] Calling Start function of httpd [sc_language.c::create_language_file():426] Create link files for <English> [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to CHS [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to RUS [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to PTB [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to DEU [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to ESP [sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock4> according to its id <ENU> [sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock4> [SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WAC104|g" > /etc/block.htm rmmod: ipt_REJECT: No such file or directory [rc debug]/bin/rc firewall restart ap_name=firewall action=restart [rc.c::rc_action():829] rc_action before add firewall - restart rc action <firewall @ restart> before file_lock. rc action <firewall @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add firewall - restart unlink running file </var/run/rc.firewall.run> [rc.c::rc_action():829] rc_action before add firewall - restart rc action <firewall @ restart> before file_lock. rc action <firewall @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add firewall - restart [rc.c::rc_stop():771] Calling Stop function of firewall [SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory [rc.c::rc_start():732] Calling Start function of firewall [SYSTEM]/usr/bin/killall -14 access_logd [SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd & [rc debug]/usr/sbin/rc syslogd create ap_name=syslogd action=create [rc.c::rc_action():829] rc_action before add syslogd - create rc action <syslogd @ create> before file_lock. rc action <syslogd @ create lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add syslogd - create [rc.c::rc_create():813] Calling Create function of syslogd unlink running file </var/run/rc.syslogd.run> [SYSTEM]/bin/echo switch=on > /proc/net/spi_enable [SYSTEM]/bin/echo clear > /proc/net/firewall_block [SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src [SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan [SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable [SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable fw_pt [SYSTEM]/usr/sbin/killall -9 usb_httpd killall: usb_httpd: no process killed [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory unlink running file </var/run/rc.firewall.run> [SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WAC104" -c '**.cgi' -t 300& unlink running file </var/run/rc.httpd.run> [rc debug]/usr/sbin/rc remote_httpd start ap_name=remote_httpd action=start [rc.c::rc_action():829] rc_action before add remote_httpd - start rc action <remote_httpd @ start> before file_lock. rc action <remote_httpd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.remote_httpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add remote_httpd - start [rc.c::rc_start():732] Calling Start function of remote_httpd unlink running file </var/run/rc.remote_httpd.run> [rc debug]/usr/sbin/rc dhcpd start ap_name=dhcpd action=start [rc.c::rc_action():829] rc_action before add dhcpd - start rc action <dhcpd @ start> before file_lock. rc action <dhcpd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dhcpd - start [rc.c::rc_start():732] Calling Start function of dhcpd killall: udhcpd: no process killed unlink running file </var/run/rc.dhcpd.run> [rc debug]/usr/sbin/rc ntp start ap_name=ntp action=start [rc.c::rc_action():829] rc_action before add ntp - start rc action <ntp @ start> before file_lock. rc action <ntp @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ntp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add ntp - start [rc.c::rc_start():732] Calling Start function of ntp [SYSTEM]/usr/sbin/netgear_ntp -z GMT+0& unlink running file </var/run/rc.ntp.run> [rc debug]/usr/sbin/rc route start ap_name=route action=start [rc.c::rc_action():829] rc_action before add route - start rc action <route @ start> before file_lock. rc action <route @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add route - start [rc.c::rc_start():732] Calling Start function of route unlink running file </var/run/rc.route.run> [rc debug]/usr/sbin/rc ripd start ap_name=ripd action=start [rc.c::rc_action():829] rc_action before add ripd - start rc action <ripd @ start> before file_lock. rc action <ripd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ripd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add ripd - start [rc.c::rc_start():732] Calling Start function of ripd unlink running file </var/run/rc.ripd.run> [rc debug]/usr/sbin/rc dnrd start ap_name=dnrd action=start [rc.c::rc_action():829] rc_action before add dnrd - start rc action <dnrd @ start> before file_lock. rc action <dnrd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dnrd - start [rc.c::rc_start():732] Calling Start function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd killall: dnrd: no process killed [SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 -o 0 -q xxx& [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 unlink running file </var/run/rc.dnrd.run> [rc debug]/usr/sbin/rc potcounter start ap_name=potcounter action=start [rc.c::rc_action():829] rc_action before add potcounter - start rc action <potcounter @ start> before file_lock. rc action <potcounter @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.potcounter.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add potcounter - start [rc.c::rc_start():732] Calling Start function of potcounter unlink running file </var/run/rc.potcounter.run> [rc debug]/usr/sbin/rc lltd start ap_name=lltd action=start [rc.c::rc_action():829] rc_action before add lltd - start rc action <lltd @ start> before file_lock. rc action <lltd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.lltd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add lltd - start [rc.c::rc_start():732] Calling Start function of lltd Notice: caching turned off Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off. unlink running file </var/run/rc.lltd.run> [rc debug]/usr/sbin/rc usb_init start ap_name=usb_init action=start [rc.c::rc_action():829] rc_action before add usb_init - start rc action <usb_init @ start> before file_lock. rc action <usb_init @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_init.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add usb_init - start [rc.c::rc_start():732] Calling Start function of usb_init [SYSTEM]/etc/mtk/mt7621_smp.sh wifi [SYSTEM]/bin/rm /etc/samba/secrets.tdb rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory [SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1 [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed [SYSTEM]/etc/mtk/mt7621_smp.sh wifi [SYSTEM]/bin/rm /etc/samba/secrets.tdb rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory [SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1 [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed unlink running file </var/run/rc.usb_init.run> [rc debug]/usr/sbin/rc debug_mode start ap_name=debug_mode action=start [rc.c::rc_action():829] rc_action before add debug_mode - start rc action <debug_mode @ start> before file_lock. rc action <debug_mode @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.debug_mode.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add debug_mode - start [rc.c::rc_start():732] Calling Start function of debug_mode unlink running file </var/run/rc.debug_mode.run> [rc debug]/usr/sbin/rc wifi_isolation start ap_name=wifi_isolation action=start [rc.c::rc_action():829] rc_action before add wifi_isolation - start rc action <wifi_isolation @ start> before file_lock. rc action <wifi_isolation @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add wifi_isolation - start [rc.c::rc_start():732] Calling Start function of wifi_isolation [wifi_isolation/wifi_isolation.c::start_wifi_isolation():46] AP Mode no need wifi_isolation! unlink running file </var/run/rc.wifi_isolation.run> [rc debug]/usr/sbin/rc mediaserver start ap_name=mediaserver action=start [rc.c::rc_action():829] rc_action before add mediaserver - start rc action <mediaserver @ start> before file_lock. rc action <mediaserver @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.mediaserver.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add mediaserver - start [rc.c::rc_start():732] Calling Start function of mediaserver #### media server is disable unlink running file </var/run/rc.mediaserver.run> [rc debug]/usr/sbin/rc bridge_iptv_port start ap_name=bridge_iptv_port action=start [rc.c::rc_action():829] rc_action before add bridge_iptv_port - start rc action <bridge_iptv_port @ start> before file_lock. rc action <bridge_iptv_port @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add bridge_iptv_port - start unlink running file </var/run/rc.bridge_iptv_port.run> [rc.c::rc_action():829] rc_action before add bridge_iptv_port - start rc action <bridge_iptv_port @ start> before file_lock. rc action <bridge_iptv_port @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add bridge_iptv_port - start unlink running file </var/run/rc.bridge_iptv_port.run> can't find this application [rc.c::rc_action():829] rc_action before add bridge_iptv_port - start rc action <bridge_iptv_port @ start> before file_lock. rc action <bridge_iptv_port @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add bridge_iptv_port - start unlink running file </var/run/rc.bridge_iptv_port.run> can't find this application [rc debug]/usr/sbin/rc vlan start ap_name=vlan action=start [rc.c::rc_action():829] rc_action before add vlan - start rc action <vlan @ start> before file_lock. rc action <vlan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.vlan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add vlan - start [rc.c::rc_start():732] Calling Start function of vlan [SYSTEM]/sbin/chmod +x /var/vlan_up.sh [SYSTEM]/bin/sh -x /var/vlan_up.sh [SYSTEM]/sbin/chmod +x /var/vlan_down.sh unlink running file </var/run/rc.vlan.run> [rc debug]/usr/sbin/rc dbus start ap_name=dbus action=start [rc.c::rc_action():829] rc_action before add dbus - start rc action <dbus @ start> before file_lock. rc action <dbus @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dbus - start unlink running file </var/run/rc.dbus.run> [rc.c::rc_action():829] rc_action before add dbus - start rc action <dbus @ start> before file_lock. rc action <dbus @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dbus - start unlink running file </var/run/rc.dbus.run> can't find this application [rc.c::rc_action():829] rc_action before add dbus - start rc action <dbus @ start> before file_lock. rc action <dbus @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dbus - start unlink running file </var/run/rc.dbus.run> can't find this application =============rc finish run smp wifi run smp wifi done PID USER VSZ STAT COMMAND 1 root 1516 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW [kworker/u:0] 6 root 0 SW [migration/0] 7 root 0 SW [migration/1] 8 root 0 SW [kworker/1:0] 9 root 0 SW [ksoftirqd/1] 10 root 0 SW< [khelper] 11 root 0 SW [kworker/1:1] 12 root 0 SW [sync_supers] 13 root 0 SW [bdi-default] 14 root 0 SW< [kblockd] 15 root 0 SW [khubd] 16 root 0 SW [kswapd0] 17 root 0 SW [fsnotify_mark] 18 root 0 SW< [xfs_mru_cache] 19 root 0 SW< [xfslogd] 20 root 0 SW< [xfsdatad] 21 root 0 SW< [xfsconvertd] 22 root 0 SW< [crypto] 31 root 0 SW [mtdblock0] 32 root 0 SW [mtdblock1] 33 root 0 SW [mtdblock2] 34 root 0 SW [mtdblock3] 35 root 0 SW [mtdblock4] 36 root 0 SW [mtdblock5] 37 root 0 SW [mtdblock6] 38 root 0 SW [mtdblock7] 39 root 0 SW [mtdblock8] 40 root 0 SW [mtdblock9] 41 root 0 SW [mtdblock10] 42 root 0 SW [mtdblock11] 43 root 0 SW [mtdblock12] 44 root 0 SW [mtdblock13] 45 root 0 SW [mtdblock14] 46 root 0 SW [mtdblock15] 47 root 0 SW [mtdblock16] 48 root 0 SW [mtdblock17] 49 root 0 SW [mtdblock18] 50 root 0 SW [mtdblock19] 51 root 0 SW [mtdblock20] 52 root 0 SW [mtdblock21] 53 root 0 SW [kworker/u:1] 60 root 0 SW [kworker/0:1] 62 root 1520 S /bin/sh /usr/etc/rcS 150 root 1032 S /sbin/klogd 152 root 920 S /usr/sbin/cmd_agent_ap 222 root 1028 S /sbin/access_logd 235 root 1140 S /sbin/access_devinfo 268 root 1216 S /usr/sbin/scfgmgr 303 root 0 SW [RtmpCmdQTask] 304 root 0 SW [RtmpWscTask] 305 root 0 SW [RtmpMlmeTask] 314 root 0 SW [RtmpCmdQTask] 315 root 0 SW [RtmpWscTask] 316 root 0 SW [RtmpMlmeTask] 337 root 1084 S miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 - 379 root 1092 S /sbin/syslogd -f /etc/syslog.conf 891 root 940 S /usr/sbin/netgear_ntp -z GMT+0 1324 root 3056 S /usr/sbin/mini_httpd -d /www -r NETGEAR WAC104 -c **. 1326 root 1104 S /usr/sbin/potcounter 1332 root 1428 S dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 1334 root 1144 S /usr/bin/lld2 br0 1448 root 1516 R /bin/ps [rc debug]/usr/sbin/rc upnp start ap_name=upnp action=start [rc.c::rc_action():829] rc_action before add upnp - start rc action <upnp @ start> before file_lock. rc action <upnp @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add upnp - start unlink running file </var/run/rc.upnp.run> [rc.c::rc_action():829] rc_action before add upnp - start rc action <upnp @ start> before file_lock. rc action <upnp @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add upnp - start unlink running file </var/run/rc.upnp.run> can't find this application [rc.c::rc_action():829] rc_action before add upnp - start rc action <upnp @ start> before file_lock. rc action <upnp @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add upnp - start [rc.c::rc_start():732] Calling Start function of upnp [upnp/upnp_cfg.c::start_upnp():68] AP Mode no need upnp unlink running file </var/run/rc.upnp.run> [rc debug]/usr/sbin/rc schedule restart [rc.c::rc_action():829] rc_action before add schedule - restart rc action <schedule @ restart> before file_lock. rc action <schedule @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.schedule.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add schedule - restart unlink running file </var/run/rc.schedule.run> [rc.c::rc_action():829] rc_action before add schedule - restart rc action <schedule @ restart> before file_lock. rc action <schedule @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.schedule.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add schedule - restart [rc.c::rc_start():732] Calling Start function of schedule [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab /usr/etc/rcS: line 294: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory /usr/etc/rcS: line 295: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory /usr/etc/rcS: line 299: cannot create /proc/sys/net/ipv4/conf/eth1/rp_filter: nonexistent directory [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule unlink running file </var/run/rc.schedule.run> failover NOT enable, run rc wan to start wan [rc debug]/usr/sbin/rc reset_lan start ap_name=reset_lan action=start [rc debug][rc.c::rc_action():829] rc_action before add reset_lan - start /usr/sbin/rc wan rc action <reset_lan @ start> before file_lock. start rc action <reset_lan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run [wan/wan.c::start_wan():1219] IPV6IPV4PPP_ONE_SESSION not enable [SYSTEM]/usr/sbin/brctl delif br0 eth3 rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add reset_lan - start unlink running file </var/run/rc.reset_lan.run> [rc.c::rc_action():829] rc_action before add reset_lan - start rc action <reset_lan @ start> before file_lock. rc action <reset_lan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add reset_lan - start unlink running file </var/run/rc.reset_lan.run> can't find this application [rc.c::rc_action():829] rc_action before add reset_lan - start rc action <reset_lan @ start> before file_lock. rc action <reset_lan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run device eth3 is not a slave of br0 rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add reset_lan - start [rc.c::rc_start():732] Calling Start function of reset_lan [SYSTEM]/usr/bin/killall netgear_ntp down port 0 Set: phy[0].reg[0] = 1840 down port 1 killall: netgear_ntp: no process killed Set: phy[1].reg[0] = 1840 killall: miniupnpd: no process killed [SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd down port 2 killall: miniupnpd: no process killed Set: phy[2].reg[0] = 1840 killall: ripd: no process killed down port 3 killall: zebra: no process killed Set: phy[3].reg[0] = 1840 killall: ripd: no process killed killall: zebra: no process killed [SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING [SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth3 -j MASQUERADE [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth3 -d ! (null) -j DROP sh: syntax error: "(" unexpected [SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down [SYSTEM]/usr/bin/killall pppd killall: pppd: no process killed [SYSTEM]/usr/bin/killall openl2tpd killall: openl2tpd: no process killed [SYSTEM]/usr/bin/killall udhcpc killall: udhcpc: no process killed [SYSTEM]/usr/bin/killall pppoe-relay killall: pppoe-relay: no process killed [SYSTEM]/sbin/ifconfig eth3 0.0.0.0 >/dev/null 2>&1 [SYSTEM]/sbin/ifconfig eth3 down [SYSTEM]/sbin/ifconfig eth3 hw ether 14:59:C0:c3:df:89 [SYSTEM]/sbin/ifconfig eth3 up [SYSTEM]/sbin/ifconfig eth3 mtu 1500 [wan/wan.c::start_wan():1429] wan_mode is <bridge> [SYSTEM]/bin/rmmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko rmmod: /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko: No such file or directory [SYSTEM]/usr/sbin/brctl addif br0 eth3 [SYSTEM]ifconfig br0 0.0.0.0 [SYSTEM]ifconfig br0 up [SYSTEM]/usr/sbin/rc route stop [rc debug]/usr/sbin/rc route stop ap_name=route action=stop [rc.c::rc_action():829] rc_action before add route - stop rc action <route @ stop> before file_lock. rc action <route @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add route - stop [rc.c::rc_stop():771] Calling Stop function of route unlink running file </var/run/rc.route.run> [SYSTEM]/usr/sbin/rc dhcpd stop [rc debug]/usr/sbin/rc dhcpd stop ap_name=dhcpd action=stop [rc.c::rc_action():829] rc_action before add dhcpd - stop rc action <dhcpd @ stop> before file_lock. rc action <dhcpd @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dhcpd - stop [rc.c::rc_stop():771] Calling Stop function of dhcpd killall: udhcpd: no process killed unlink running file </var/run/rc.dhcpd.run> [SYSTEM]/usr/sbin/rc igmp stop [rc debug]/usr/sbin/rc igmp stop ap_name=igmp action=stop [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop unlink running file </var/run/rc.igmp.run> [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop unlink running file </var/run/rc.igmp.run> can't find this application [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop [rc.c::rc_stop():771] Calling Stop function of igmp iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). killall: igmpproxy: no process killed [SYSTEM]/bin/echo igmp_snooping 0 > /proc/sw_ar8327 sh: cannot create /proc/sw_ar8327: nonexistent directory [SYSTEM]/bin/echo ssdp_flooding 0 > /proc/sw_ar8327 sh: cannot create /proc/sw_ar8327: nonexistent directory [SYSTEM]/bin/echo write.g 0x060c 0x8000 0x0001 > /proc/sw_ar8327 sh: cannot create /proc/sw_ar8327: nonexistent directory unlink running file </var/run/rc.igmp.run> [SYSTEM]/usr/bin/insmod /lib/modules/dns_hijack.ko [SYSTEM]/usr/sbin/killall -9 udhcpc killall: udhcpc: no process killed [SYSTEM]/usr/sbin/udhcpc -i br0 -s /etc/udhcpc.ap.script & [dhcpc.c::udhcpc():443] udhcp client (v0.9.7) started [clientpacket.c::send_discover():175] Sending discover... up port 0 Set: phy[0].reg[0] = 1240 up port 1 Set: phy[1].reg[0] = 1240 up port 2 Set: phy[2].reg[0] = 1240 up port 3 Set: phy[3].reg[0] = 1240 unlink running file </var/run/rc.reset_lan.run> preapre_sys_for_3g mknod: /dev/zero: File exists mknod: /dev/ttyUSB0: File exists mknod: /dev/ttyUSB1: File exists mknod: /dev/ttyUSB2: File exists mknod: /dev/ttyUSB3: File exists mkdir: cannot create directory '/var': File exists preapre_sys_for_3g done failover NOT enable [clientpacket.c::send_discover():175] Sending discover... [clientpacket.c::send_discover():175] Sending discover... cable_down_once [rc debug]/usr/sbin/rc down_manage stop ap_name=down_manage action=stop [rc.c::rc_action():829] rc_action before add down_manage - stop rc action <down_manage @ stop> before file_lock. rc action <down_manage @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add down_manage - stop unlink running file </var/run/rc.down_manage.run> [rc.c::rc_action():829] rc_action before add down_manage - stop rc action <down_manage @ stop> before file_lock. rc action <down_manage @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run [rc debug]/usr/sbin/rc lan ap_down ap_name=lan action=ap_down [rc.c::rc_action():829] rc_action before add lan - ap_down rc action <lan @ ap_down> before file_lock. rc action <lan @ ap_down lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.lan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add down_manage - stop unlink running file </var/run/rc.down_manage.run> can't find this application [rc.c::rc_action():829] rc_action before add down_manage - stop rc action <down_manage @ stop> before file_lock. rc action <down_manage @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add lan - ap_down [SYSTEM]/usr/sbin/ip route del to default 2>/dev/null rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add down_manage - stop unlink running file </var/run/rc.down_manage.run> can't find this application [rc debug]/usr/sbin/rc usb_printer start ap_name=usb_printer action=start [rc.c::rc_action():829] rc_action before add usb_printer - start rc action <usb_printer @ start> before file_lock. rc action <usb_printer @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add usb_printer - start unlink running file </var/run/rc.usb_printer.run> [rc.c::rc_action():829] rc_action before add usb_printer - start rc action <usb_printer @ start> before file_lock. rc action <usb_printer @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add usb_printer - start unlink running file </var/run/rc.usb_printer.run> can't find this application [rc.c::rc_action():829] rc_action before add usb_printer - start rc action <usb_printer @ start> before file_lock. rc action <usb_printer @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add usb_printer - start [rc.c::rc_start():732] Calling Start function of usb_printer [SYSTEM]/sbin/killall KC_BONJOUR killall: KC_BONJOUR: no process killed [SYSTEM]/usr/sbin/rc dnrd stop [SYSTEM]/sbin/killall KC_PRINT [rc debug]/usr/sbin/rc dnrd stop ap_name=dnrd action=stop [rc.c::rc_action():829] rc_action before add dnrd - stop rc action <dnrd @ stop> before file_lock. rc action <dnrd @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dnrd - stop [rc.c::rc_stop():771] Calling Stop function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 killall: KC_PRINT: no process killed [SYSTEM]/sbin/rmmod usblp rmmod: usblp: No such file or directory [SYSTEM]/sbin/rmmod NetUSB.ko rmmod: NetUSB.ko: No such file or directory [SYSTEM]/sbin/rmmod GPL_NetUSB.ko iptables: No chain/target/match by that name. rmmod: GPL_NetUSB.ko: No such file or directory [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 unlink running file </var/run/rc.usb_printer.run> PID USER VSZ STAT COMMAND 1 root 1516 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW [kworker/u:0] 6 root 0 SW [migration/0] 7 root 0 SW [migration/1] 8 root 0 SW [kworker/1:0] 9 root 0 SW [ksoftirqd/1] 10 root 0 SW< [khelper] 11 root 0 SW [kworker/1:1] 12 root 0 SW [sync_supers] 13 root 0 SW [bdi-default] 14 root 0 SW< [kblockd] 15 root 0 SW [khubd] 16 root 0 SW [kswapd0] [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 17 root 0 SW [fsnotify_mark] 18 root 0 SW< [xfs_mru_cache] 19 root 0 SW< [xfslogd] 20 root 0 SW< [xfsdatad] 21 root 0 SW< [xfsconvertd] 22 root 0 SW< [crypto] 31 root 0 SW [mtdblock0] 32 root 0 SW [mtdblock1] 33 root 0 SW [mtdblock2] 34 root 0 SW [mtdblock3] 35 root 0 SW [mtdblock4] 36 root 0 SW [mtdblock5] 37 root 0 SW [mtdblock6] 38 root 0 SW [mtdblock7] 39 root 0 SW [mtdblock8] 40 root 0 SW [mtdblock9] 41 root 0 SW [mtdblock10] 42 root 0 SW [mtdblock11] 43 root 0 SW [mtdblock12] 44 root 0 SW [mtdblock13] 45 root 0 SW [mtdblock14] 46 root 0 SW [mtdblock15] 47 root 0 SW [mtdblock16] 48 root 0 SW [mtdblock17] 49 root 0 SW [mtdblock18] 50 root 0 SW [mtdblock19] 51 root 0 SW [mtdblock20] 52 root 0 SW [mtdblock21] 53 root 0 SW [kworker/u:1] 60 root 0 SW [kworker/0:1] 62 root 1520 S /bin/sh /usr/etc/rcS 150 root 1032 S /sbin/klogd 152 root 920 S /usr/sbin/cmd_agent_ap 222 root 1028 S /sbin/access_logd 235 root 1140 S /sbin/access_devinfo 268 root 1216 S /usr/sbin/scfgmgr 303 root 0 SW [RtmpCmdQTask] 304 root 0 SW [RtmpWscTask] 305 root 0 SW [RtmpMlmeTask] 314 root 0 SW [RtmpCmdQTask] 315 root 0 SW [RtmpWscTask] 316 root 0 SW [RtmpMlmeTask] 337 root 1084 S miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 - 379 root 1092 S /sbin/syslogd -f /etc/syslog.conf 1324 root 3056 S /usr/sbin/mini_httpd -d /www -r NETGEAR WAC104 -c **. 1326 root 1104 S /usr/sbin/potcounter 1332 root 1428 S dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 1334 root 1144 S /usr/bin/lld2 br0 1457 root 948 S /usr/sbin/crond 1458 root 1404 S /usr/sbin/multi_pb_app 90 91 92 10 50 1460 root 0 Z [crond] 1461 root 0 Z [crond] 1510 root 2136 S /usr/sbin/rc wan start 1512 root 924 S /usr/sbin/cmd_agent 2096 root 1108 S /usr/sbin/udhcpc -i br0 -s /etc/udhcpc.ap.script 2247 root 1104 S usr/sbin/wan_monitor 2248 root 1296 S usr/sbin/ap_monitor 2270 root 1512 S sh -c /usr/sbin/rc lan ap_down 2272 root 2116 S /usr/sbin/rc lan ap_down 2282 root 936 S /usr/sbin/watchdog 2298 root 1512 S sh -c /usr/sbin/rc dnrd stop 2301 root 2124 S /usr/sbin/rc dnrd stop 2415 root 1516 R /bin/ps 2521 root 1512 S sh -c iptables -t nat -D PREROUTING -i br0 -p udp --d 2522 root 1760 R iptables -t nat -D PREROUTING -i br0 -p udp --dport 5 /usr/etc/rcS: line 376: /usr/sbin/led_test: not found iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd [rc debug]/usr/sbin/rc check_kwilt start ap_name=check_kwilt action=start [rc.c::rc_action():829] rc_action before add check_kwilt - start rc action <check_kwilt @ start> before file_lock. rc action <check_kwilt @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.check_kwilt.run /usr/etc/rcS: line 379: /usr/sbin/kwilt_daemon: not found starting pid 2633, tty '/dev/ttyS1': '/bin/sh' rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add check_kwilt - start unlink running file </var/run/rc.check_kwilt.run> [rc.c::rc_action():829] rc_action before add check_kwilt - start rc action <check_kwilt @ start> before file_lock. rc action <check_kwilt @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.check_kwilt.run # unlink running file </var/run/rc.dnrd.run> rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add check_kwilt - start unlink running file </var/run/rc.check_kwilt.run> can't find this application [rc.c::rc_action():829] rc_action before add check_kwilt - start rc action <check_kwilt @ start> before file_lock. rc action <check_kwilt @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.check_kwilt.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add check_kwilt - start unlink running file </var/run/rc.check_kwilt.run> can't find this application [SYSTEM]/usr/sbin/rc wan restart [rc debug]/usr/sbin/rc wan restart [SYSTEM]/usr/bin/killall netgear_ntp killall: netgear_ntp: no process killed killall: miniupnpd: no process killed [SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd killall: miniupnpd: no process killed killall: ripd: no process killed killall: zebra: no process killed [basic/lan_cfg.c::start_lan_ap():329] udhcpc cannot get IP, run autoip app to generate IP for br0 [SYSTEM]/usr/sbin/killall -SIGUSR2 udhcpc [dhcpc.c::release_requested():161] Received SIGUSR2, state=0,sig=17 [SYSTEM]/usr/sbin/autoip We will test autoip: 192.168.0.100 send 0 request pkgs killall: ripd: no process killed killall: zebra: no process killed [SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING [SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth3 -j MASQUERADE [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth3 -d ! (null) -j DROP sh: syntax error: "(" unexpected [SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down [SYSTEM]/usr/bin/killall pppd killall: pppd: no process killed [SYSTEM]/usr/bin/killall openl2tpd send 1 request pkgs killall: openl2tpd: no process killed [SYSTEM]/usr/bin/killall udhcpc [dhcpc.c::release_requested():161] Received SIGUSR2, state=7,sig=0 [dhcpc.c::terminate():206] Received SIGTERM [SYSTEM]/usr/bin/killall pppoe-relay killall: pppoe-relay: no process killed [SYSTEM]/sdevice eth3 left promiscuous mode bibr0: port 4(eth3) entering forwarding state n/ifconfig eth3 0.0.0.0 >/dev/null 2>&1 [wan/wan.c::start_wan():1219] IPV6IPV4PPP_ONE_SESSION not enable [SYSTEM]/usr/sbin/brctl delif br0 eth3 [SYSTEM]/usr/bin/killall netgear_ntp killall: netgear_ntp: no process killed killall: miniupnpd: no process killed [SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd killall: miniupnpd: no process killed killall: ripd: no process killed killall: zebra: no process killed send 2 request pkgs We will do announce for autoip: 192.168.0.100 send 0 request pkgs killall: ripd: no process killed killall: zebra: no process killed [SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING [SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth3 -j MASQUERADE [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth3 -d ! (null) -j DROP sh: syntax error: "(" unexpected [SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down [SYSTEM]/usr/bin/killall pppd killall: pppd: no process killed [SYSTEM]/usr/bin/killall openl2tpd killall: openl2tpd: no process killed [SYSTEM]/usr/bin/killall udhcpc killall: udhcpc: no process killed [SYSTEM]/usr/bin/killall pppoe-relay killall: pppoe-relay: no process killed [SYSTEM]/sbin/ifconfig eth3 0.0.0.0 >/dev/null 2>&1 [SYSTEM]/sbin/ifconfigNOTIFY eth3 down eth3: ===> VirtualIF_close NOTIFY [SYSTEM]/sbin/ifconfigGDMA2_MAC_ADRH -- : 0x00001459 eGDMA2_MAC_ADRL -- : 0xc0c3df89 th3NOTIFY hw ether 14:59:C0:c3:df:89 NOTIFY [eth3: ===> VirtualIF_open SYSNOTIFY TEM]/sbin/ifconfig eth3 up [SYSTEM]/sbin/ifconfig eth3 mtu 1500 [wan/wan.c::start_wan():1429] wan_mode is <bridge> [SYdevice eth3 entered promiscuous mode STEbr0: port 4(eth3) entering listening state M]br0: port 4(eth3) entering listening state /bin/rmmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko rmmod: /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko: No such file or directory [SYSTEM]/usr/sbin/brctl addif br0 eth3 [SYSTEM]ifconfig br0 0.0.0.0 [SYSTEM]ifconfig br0 up [SYSTEM]/usr/sbin/rc route stop [rc debug]/usr/sbin/rc route stop ap_name=route action=stop [rc.c::rc_action():829] rc_action before add route - stop rc action <route @ stop> before file_lock. rc action <route @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add route - stop [rc.c::rc_stop():771] Calling Stop function of route unlink running file </var/run/rc.route.run> [SYSTEM]/usr/sbin/rc dhcpd stop [rc debug]/usr/sbin/rc dhcpd stop ap_name=dhcpd action=stop [rc.c::rc_action():829] rc_action before add dhcpd - stop rc action <dhcpd @ stop> before file_lock. rc action <dhcpd @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dhcpd - stop [rc.c::rc_stop():771] Calling Stop function of dhcpd killall: udhcpd: no process killed unlink running file </var/run/rc.dhcpd.run> [SYSTEM]/usr/sbin/rc igmp stop [rc debug]/usr/sbin/rc igmp stop ap_name=igmp action=stop [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop unlink running file </var/run/rc.igmp.run> [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop unlink running file </var/run/rc.igmp.run> can't find this application [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop [rc.c::rc_stop():771] Calling Stop function of igmp iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). killall: igmpproxy: no process killed [SYSTEM]/bin/echo igmp_snooping 0 > /proc/sw_ar8327 sh: cannot create /proc/sw_ar8327: nonexistent directory [SYSTEM]/bin/echo ssdp_flooding 0 > /proc/sw_ar8327 sh: cannot create /proc/sw_ar8327: nonexistent directory [SYSTEM]/bin/echo write.g 0x060c 0x8000 0x0001 > /proc/sw_ar8327 sh: cannot create /proc/sw_ar8327: nonexistent directory unlink running file </var/run/rc.igmp.run> [SYSTEM]/usr/bin/insmod /lib/modules/dns_hijack.ko insmod: cannot insert '/lib/modules/dns_hijack.ko': File exists [SYSTEM]/usr/sbin/killall -9 udhcpc killall: udhcpc: no process killed [SYSTEM]/usr/sbin/udhcpc -i br0 -s /etc/udhcpc.ap.script & [dhcpc.c::udhcpc():443] udhcp client (v0.9.7) started [clientpacket.c::send_discover():175] Sending discover... br0: port 4(eth3) entering learning state send 1 request pkgs br0: topology change detected, propagating br0: port 4(eth3) entering forwarding state [clientpacket.c::send_discover():175] Sending discover... probe success with latest probe IP [clientpacket.c::send_discover():175] Sending discover... [SYSTEM]/usr/sbin/killall -SIGUSR1 udhcpc [dhcpc.c::renew_requested():139] Received SIGUSR1 or sig 50, state=0 [clientpacket.c::send_discover():175] Sending discover... [basic/lan_cfg.c::start_lan_ap():338] autoip generate a IP for br0, use it and run lan ap up [rc debug]/usr/sbin/rc dnrd restart ap_name=dnrd action=restart [rc.c::rc_action():829] rc_action before add dnrd - restart rc action <dnrd @ restart> before file_lock. rc action <dnrd @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dnrd - restart [rc.c::rc_stop():771] Calling Stop function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd killall: dnrd: no process killed [rc.c::rc_start():732] Calling Start function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd killall: dnrd: no process killed [SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 -o 0 -q xxx& [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 unlink running file </var/run/rc.dnrd.run> [rc debug]/usr/sbin/rc httpd restart ap_name=httpd action=restart [rc.c::rc_action():829] rc_action before add httpd - restart rc action <httpd @ restart> before file_lock. rc action <httpd @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add httpd - restart [rc.c::rc_stop():771] Calling Stop function of httpd killall: remote_httpd: no process killed Notice: caching turned off Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off. [rc.c::rc_start():732] Calling Start function of httpd [sc_language.c::create_language_file():426] Create link files for <English> [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to CHS [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to RUS [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to PTB [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to DEU [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to ESP [sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock4> according to its id <ENU> [sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock4> ln: /tmp/www/www.eng: Read-only file system [SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WAC104|g" > /etc/block.htm [rc debug]/bin/rc firewall restart ap_name=firewall action=restart [rc.c::rc_action():829] rc_action before add firewall - restart rc action <firewall @ restart> before file_lock. rc action <firewall @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add firewall - restart unlink running file </var/run/rc.firewall.run> [rc.c::rc_action():829] rc_action before add firewall - restart rc action <firblock items: ewall @ restart> beinput:clear fore file_lock. rc action <ficlamp total entry used:0 rewall @ restart lock = 3> after file_loctotal count:0 k. input str:clear [Spsd clear oldest entry YSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.runroc_write_echo_chargen receive: len: 6, input: clear proc_write_echo_chargen receive: clear list Leaving proc_write_echo_chargen : size: 6 rc action < unlock = 3> after fwan interface=[eth3], index=9 ibr interface=[br0], index=8 le_lock. [rc.c::rc_action():837] rc_action after add firewall - restart [rc.c::rc_stop():771] Calling Stop function of firewall [SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory [rc.c::rc_start():732] Calling Start function of firewall [SYSTEM]/usr/bin/killall -14 access_logd [SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd & [rc debug]/usr/sbin/rc syslogd create ap_name=syslogd action=create [rc.c::rc_action():829] rc_action before add syslogd - create rc action <syslogd @ create> before file_lock. rc action <syslogd @ create lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add syslogd - create [rc.c::rc_create():813] Calling Create function of syslogd unlink running file </var/run/rc.syslogd.run> [SYSTEM]/bin/echo switch=on > /proc/net/spi_enable [SYSTEM]/bin/echo clear > /proc/net/firewall_block [SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src [SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan [SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable [SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable fw_pt [SYSTEM]/usr/sbin/killall -9 usb_httpd killall: usb_httpd: no process killed [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [clientpacket.c::send_discover():175] Sending discover... [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory unlink running file </var/run/rc.firewall.run> [SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WAC104" -c '**.cgi' -t 300& unlink running file </var/run/rc.httpd.run> [SYSTEM]/bin/cp -f /etc/group.smb /etc/group 2>/dev/null [SYSTEM]/bin/cp -f /etc/passwd.smb /etc/passwd 2>/dev/null [SYSTEM]/bin/cp -f /etc/samba.conf/smbpasswd /etc/samba/smbpasswd 2>/dev/null [SYSTEM]/bin/cp -f /etc/samba.conf/smb.conf /etc/samba/smb.conf 2>/dev/null [clientpacket.c::send_discover():175] Sending discover... username=admin,passwd=password [basic/lan_cfg.c::start_lan_ap():322] udhcpc get IP [SYSTEM]/usr/sbin/rc dnrd start [rc debug]/usr/sbin/rc dnrd start ap_name=dnrd action=start [rc.c::rc_action():829] rc_action before add dnrd - start rc action <dnrd @ start> before file_lock. rc action <dnrd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dnrd - start [rc.c::rc_start():732] Calling Start function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd [SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 -o 0 -q xxx& [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 Notice: caching turned off Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off. unlink running file </var/run/rc.dnrd.run> [SYSTEM]/usr/sbin/rc route start [rc debug]/usr/sbin/rc route start ap_name=route action=start [rc.c::rc_action():829] rc_action before add route - start rc action <route @ start> before file_lock. rc action <route @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run startsmbfilepwent_internal: file /etc/samba/smbpasswd did not exist. File successfully created. rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add route - start [rc.c::rc_start():732] Calling Start function of route unlink running file </var/run/rc.route.run> [SYSTEM]/bin/killall failover killall: failover: no process killed [wan/wan.c::start_wan():1513] ipv6 restart, v4 mode bridge v6 mode disable [SYSTEM]/usr/sbin/rc ipv6 restart [rc debug]/usr/sbin/rc ipv6 restart ap_name=ipv6 action=restart [rc.c::rc_action():829] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add ipv6 - restart unlink running file </var/run/rc.ipv6.run> [rc.c::rc_action():829] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add ipv6 - restart unlink running file </var/run/rc.ipv6.run> can't find this application [rc.c::rc_action():829] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add ipv6 - restart [rc.c::rc_stop():771] Calling Stop function of ipv6 [ipv6/ipv6.c::stop_ipv6():30] AP Mode no need ipv6. [rc.c::rc_start():732] Calling Start function of ipv6 [ipv6/ipv6.c::start_ipv6():102] AP Mode no need ipv6. unlink running file </var/run/rc.ipv6.run> [SYSTEM]/usr/sbin/rc qos stop [rc debug]/usr/sbin/rc qos stop ap_name=qos action=stop [rc.c::rc_action():829] rc_action before add qos - stop rc action <qos @ stop> before file_lock. rc action <qos @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.qos.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add qos - stop unlink running file </var/run/rc.qos.run> [rc.c::rc_action():829] rc_action before add qos - stop rc action <qos @ stop> before file_lock. rc action <qos @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.qos.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add qos - stop [rc.c::rc_stop():771] Calling Stop function of qos [SYSTEM]/usr/sbin/tc qdisc del dev eth3 root 2> /dev/null Added user admin. ---------------- [SYSTEM]echo "0," > /proc/qos [SYSTEM]/usr/sbin/nmbd -s /etc/samba/smb.conf -D -P 19 sh: cannot create /proc/qos: nonexistent directory [SYSTEM]echo 0 > /proc/sys/net/netfilter/nf_conntrack_acct [SYSTEM]/sbin/rmmod /lib/modules/sc_priority.ko [rc debug]/usr/sbin/rc lan restart ap_name=lan action=restart [rc.c::rc_action():829] rc_action before add lan - restart rc action <lan @ restart> before file_lock. rc action <lan @ restart lock = 3> after file_lock. rc action <lan@41> exit without remove running flag file. rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add lan - restart [rc.c::rc_stop():771] Calling Stop function of lan rmmod: /lib/modules/sc_priority.ko: No such file or directory [rc.c::rc_start():732] Calling Start function of lan [SYSTEM]/usr/sbin/brctl setfd br0 1 [SYSTEM]/usr/sbin/tc qdisc del dev br0 root 2> /dev/null [SYSTEM]ifconfig br0 0.0.0.0 [SYSTEM]/usr/sbin/iptables -t mangle -F POSTROUTING [SYSTEM]ifconfig br0 up [SYSTEM]/usr/sbin/rc route stop [rc debug]/usr/sbin/rc route stop ap_name=route action=stop [rc.c::rc_action():829] rc_action before add route - stop rc action <route @ stop> before file_lock. rc action <route @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add route - stop [rc.c::rc_stop():771] Calling Stop function of route unlink running file </var/run/rc.route.run> [SYSTEM]/usr/sbin/rc dhcpd stop [SYSTEM]/usr/sbin/iptables -t mangle -F TURBO_VIDEO [rc debug]/usr/sbin/rc dhcpd stop ap_name=dhcpd action=stop [rc.c::rc_action():829] rc_action before add dhcpd - stop rc action <dhcpd @ stop> before file_lock. rc action <dhcpd @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dhcpd - stop [rc.c::rc_stop():771] Calling Stop function of dhcpd killall: udhcpd: no process killed iptables: No chain/target/match by that name. unlink running file </var/run/rc.dhcpd.run> [SYSTEM]/usr/sbin/iptables -t mangle -X TURBO_VIDEO [SYSTEM]/usr/sbin/rc igmp stop [rc debug]/usr/sbin/rc igmp stop ap_name=igmp action=stop [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run iptables: [SYSTEM]/usr/sbin/rc usb_service restart No chain/target/match by that name. unlink running file </var/run/rc.qos.run> [SYSTEM]/usr/sbin/rc httpd restart [rc debug]/usr/sbin/rc usb_service restart ap_name=usb_service action=restart [rc.c::rc_action():829] rc_action before add usb_service - restart rc action <usb_service @ restart> before file_lock. rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop unlink running file </var/run/rc.igmp.run> [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run rc action <usb_service @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop unlink running file </var/run/rc.igmp.run> can't find this application [rc.c::rc_action():829] rc_action before add igmp - stop rc action <igmp @ stop> before file_lock. rc action <igmp @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.igmp.run [rc debug]/usr/sbin/rc httpd restart ap_name=httpd action=restart [rc.c::rc_action():829] rc_action before add httpd - restart rc action <httpd @ restart> before file_lock. rc action <httpd @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add usb_service - restart unlink running file </var/run/rc.usb_service.run> [rc.c::rc_action():829] rc_action before add usb_service - restart rc action <usb_service @ restart> before file_lock. rc action <usb_service @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add httpd - restart [rc.c::rc_stop():771] Calling Stop function of httpd rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add igmp - stop [rc.c::rc_stop():771] Calling Stop function of igmp rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add usb_service - restart unlink running file </var/run/rc.usb_service.run> can't find this application [rc.c::rc_action():829] rc_action before add usb_service - restart rc action <usb_service @ restart> before file_lock. rc action <usb_service @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add usb_service - restart [rc.c::rc_stop():771] Calling Stop function of usb_service [SYSTEM]/etc/mtk/mt7621_smp.sh wifi killall: remote_httpd: no process killed [rc.c::rc_start():732] Calling Start function of httpd [sc_language.c::create_language_file():426] Create link files for <English> iptables: Bad rule (does a matching rule exist in that chain?). [SYSTEM]/bin/rm /etc/samba/secrets.tdb iptables: Bad rule (does a matching rule exist in that chain?). rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory [SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1 killall: igmpproxy: no process killed [SYSTEM]/bin/echo igmp_snooping 0 > /proc/sw_ar8327 sh: cannot create /proc/sw_ar8327: nonexistent directory [SYSTEM]/bin/echo ssdp_flooding 0 > /proc/sw_ar8327 [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU sh: cannot create /proc/sw_ar8327: nonexistent directory [SYSTEM]/bin/echo write.g 0x060c 0x8000 0x0001 > /proc/sw_ar8327 sh: cannot create /proc/sw_ar8327: nonexistent directory [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 unlink running file </var/run/rc.igmp.run> [SYSTEM]/usr/bin/insmod /lib/modules/dns_hijack.ko [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed [rc.c::rc_start():732] Calling Start function of usb_service [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to CHS [SYSTEM]/usr/sbin/killall -9 hd-idle insmod: cannot insert '/lib/modules/dns_hijack.ko': File exists [SYSTEM]/usr/sbin/killall -9 udhcpc killall: hd-idle: no process killed [SYSTEM]/usr/sbin/udhcpc -i br0 -s /etc/udhcpc.ap.script & [dhcpc.c::udhcpc():443] udhcp client (v0.9.7) started unlink running file </var/run/rc.usb_service.run> [rc debug]/usr/sbin/rc wifi_isolation restart ap_name=wifi_isolation action=restart [rc.c::rc_action():829] rc_action before add wifi_isolation - restart rc action <wifi_isolation @ restart> before file_lock. rc action <wifi_isolation @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add wifi_isolation - restart [rc.c::rc_stop():771] Calling Stop function of wifi_isolation [SYSTEM]/sbin/rmmod /lib/modules/wifi_isolation.ko rmmod: /lib/modules/wifi_isolation.ko: No such file or directory [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to RUS [rc.c::rc_start():732] Calling Start function of wifi_isolation [clientpacket.c::send_discover():175] Sending discover... [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to PTB [wifi_isolation/wifi_isolation.c::start_wifi_isolation():46] AP Mode no need wifi_isolation! unlink running file </var/run/rc.wifi_isolation.run> [SYSTEM]/usr/sbin/rc dnrd start [rc debug]/usr/sbin/rc dnrd start ap_name=dnrd action=start [rc.c::rc_action():829] rc_action before add dnrd - start rc action <dnrd @ start> before file_lock. rc action <dnrd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dnrd - start [rc.c::rc_start():732] Calling Start function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to DEU iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd [SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 -o 0 -q xxx& [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 unlink running file </var/run/rc.dnrd.run> [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to ESP [sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock4> according to its id <ENU> [SYSTEM]/usr/sbin/rc route start [rc debug]/usr/sbin/rc route start ap_name=route action=start [rc.c::rc_action():829] rc_action before add route - start rc action <route @ start> before file_lock. rc action <route @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add route - start [rc.c::rc_start():732] Calling Start function of route unlink running file </var/run/rc.route.run> [SYSTEM]/bin/killall failover killall: failover: no process killed [wan/wan.c::start_wan():1513] ipv6 restart, v4 mode bridge v6 mode disable [SYSTEM]/usr/sbin/rc ipv6 restart [rc debug]/usr/sbin/rc ipv6 restart ap_name=ipv6 action=restart [rc.c::rc_action():829] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add ipv6 - restart unlink running file </var/run/rc.ipv6.run> [rc.c::rc_action():829] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run [sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock4> rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add ipv6 - restart unlink running file </var/run/rc.ipv6.run> can't find this application [rc.c::rc_action():829] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run block items: unlock = 3> after file_lock. [rc.c::rc_actioninput:clear ():837] rc_action after add ipv6 - restarclamp total entry used:0 t [rc.c::rc_stop():771] Calling Stop functitotal count:0 on of ipv6 [input str:clear ippsd clear oldest entry v6/ipv6.c::stop_ipv6():30] AP Mode no need ipv6. [rc.c::rc_st proc_write_echo_chargen receive: len: 6, input: clear ar proc_write_echo_chargen receive: clear list t( Leaving proc_write_echo_chargen : size: 6 ):732] Calling Start function of ipv6 [ipv6/ipv6.cwan interface=[eth3], index=9 ::br interface=[br0], index=8 start_ipv6():102] AP Mode no need ipv6. unlink running file </var/run/rc.ipv6.run> ln: /tmp/www/www.eng: Read-only file system [SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WAC104|g" > /etc/block.htm [rc debug]/bin/rc firewall restart ap_name=firewall action=restart [rc.c::rc_action():829] rc_action before add firewall - restart rc action <firewall @ restart> before file_lock. rc action <firewall @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add firewall - restart unlink running file </var/run/rc.firewall.run> [rc.c::rc_action():829] rc_action before add firewall - restart rc action <firewall @ restart> before file_lock. rc action <firewall @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add firewall - restart [rc.c::rc_stop():771] Calling Stop function of firewall [SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory [rc.c::rc_start():732] Calling Start function of firewall [SYSTEM]/usr/bin/killall -14 access_logd [SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd & [rc debug]/usr/sbin/rc syslogd create ap_name=syslogd action=create [rc.c::rc_action():829] rc_action before add syslogd - create rc action <syslogd @ create> before file_lock. rc action <syslogd @ create lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add syslogd - create [rc.c::rc_create():813] Calling Create function of syslogd unlink running file </var/run/rc.syslogd.run> [SYSTEM]/bin/echo switch=on > /proc/net/spi_enable [SYSTEM]/bin/echo clear > /proc/net/firewall_block [SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src [SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan [SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable [SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable fw_pt [SYSTEM]/usr/sbin/killall -9 usb_httpd killall: usb_httpd: no process killed [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab ERROR: isock: Couldn't bind local address [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory unlink running file </var/run/rc.firewall.run> [SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WAC104" -c '**.cgi' -t 300& unlink running file </var/run/rc.httpd.run> [SYSTEM]/usr/sbin/rc dnrd start [rc debug]/usr/sbin/rc dnrd start ap_name=dnrd action=start [rc.c::rc_action():829] rc_action before add dnrd - start rc action <dnrd @ start> before file_lock. rc action <dnrd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add dnrd - start [rc.c::rc_start():732] Calling Start function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [clientpacket.c::send_discover():175] Sending discover... [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd [SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 -o 0 -q xxx& [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 ERROR: isock: Couldn't bind local address unlink running file </var/run/rc.dnrd.run> [SYSTEM]/bin/cp -f /etc/group.smb /etc/group 2>/dev/null [SYSTEM]/bin/cp -f /etc/passwd.smb /etc/passwd 2>/dev/null [SYSTEM]/bin/cp -f /etc/samba.conf/smbpasswd /etc/samba/smbpasswd 2>/dev/null [SYSTEM]/bin/cp -f /etc/samba.conf/smb.conf /etc/samba/smb.conf 2>/dev/null [clientpacket.c::send_discover():175] Sending discover... username=admin,passwd=password ---------------- [SYSTEM]/usr/bin/killall -9 nmbd 2>/dev/null [SYSTEM]/usr/sbin/nmbd -s /etc/samba/smb.conf -D -P 19 unlink running file </var/run/rc.lan.run> Usage: rc [wan|service|ap name] [start|stop|restart|create] [basic/lan_cfg.c::start_lan_ap():329] udhcpc cannot get IP, run autoip app to generate IP for br0 [SYSTEM]/usr/sbin/killall -SIGUSR2 udhcpc [dhcpc.c::release_requested():161] Received SIGUSR2, state=0,sig=17 [SYSTEM]/usr/sbin/autoip We will test autoip: 192.168.0.100 send 0 request pkgs send 1 request pkgs send 2 request pkgs We will do announce for autoip: 192.168.0.100 send 0 request pkgs send 1 request pkgs probe success with latest probe IP [SYSTEM]/usr/sbin/killall -SIGUSR1 udhcpc [dhcpc.c::renew_requested():139] Received SIGUSR1 or sig 50, state=7 [basic/lan_cfg.c::start_lan_ap():338] autoip generate a IP for br0, use it and run lan ap up [rc debug]/usr/sbin/rc dnrd restart ap_name=dnrd action=restart [rc.c::rc_action():829] rc_action before add dnrd - restart rc action <dnrd @ restart> before file_lock. rc action <dnrd @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 3> after file_lock. [clientpacket.c::send_discover():175] Sending discover... [rc.c::rc_action():837] rc_action after add dnrd - restart [rc.c::rc_stop():771] Calling Stop function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd killall: dnrd: no process killed [rc.c::rc_start():732] Calling Start function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd killall: dnrd: no process killed [SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 -o 0 -q xxx& Notice: caching turned off[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off. unlink running file </var/run/rc.dnrd.run> [rc debug]/usr/sbin/rc httpd restart ap_name=httpd action=restart [rc.c::rc_action():829] rc_action before add httpd - restart rc action <httpd @ restart> before file_lock. rc action <httpd @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add httpd - restart [rc.c::rc_stop():771] Calling Stop function of httpd killall: remote_httpd: no process killed [rc.c::rc_start():732] Calling Start function of httpd [sc_language.c::create_language_file():426] Create link files for <English> [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to CHS [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to RUS [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to PTB [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to DEU [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to ESP [sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock4> according to its id <ENU> [sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock4> ln: /tmp/www/www.eng: Read-only file system [SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WAC104|g" > /etc/block.htm [rc debug]/bin/rc firewall restart ap_name=firewall action=restart [rc.c::rc_action():829] rc_action before add firewall - restart rc action <firewall @ restart> before file_lock. rc action <firewall @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():837] rc_action after add firewall - restart unlink running file </var/run/rc.firewall.run> [rc.c::rc_action():829] rc_action before add firewall - restart rc action <firewalblock items: l @ restart> befoinput:clear re file_lock. rc action <firewall @ restart lock = 3> clamp total entry used:0 after file_lock. [SYSTEM]/bin/ctotal count:0 p /proc/uptiminput str:clear e psd clear oldest entry /var/run/rc.firewall.run rc action < unlock proc_write_echo_chargen receive: len: 6, input: clear = proc_write_echo_chargen receive: clear list 3 Leaving proc_write_echo_chargen : size: 6 > after file_lock. [rc.c::rc_awan interface=[eth3], index=9 cbr interface=[br0], index=8 tion():837] rc_action after add firewall - restart [rc.c::rc_stop():771] Calling Stop function of firewall [SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory [rc.c::rc_start():732] Calling Start function of firewall [SYSTEM]/usr/bin/killall -14 access_logd [SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd & [rc debug]/usr/sbin/rc syslogd create ap_name=syslogd action=create [rc.c::rc_action():829] rc_action before add syslogd - create rc action <syslogd @ create> before file_lock. rc action <syslogd @ create lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add syslogd - create [rc.c::rc_create():813] Calling Create function of syslogd unlink running file </var/run/rc.syslogd.run> [SYSTEM]/bin/echo switch=on > /proc/net/spi_enable [SYSTEM]/bin/echo clear > /proc/net/firewall_block [SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src [SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan [SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable [SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable fw_pt [SYSTEM]/usr/sbin/killall -9 usb_httpd killall: usb_httpd: no process killed [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [flash.c::sc_get_region():328] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory unlink running file </var/run/rc.firewall.run> [SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WAC104" -c '**.cgi' -t 300& unlink running file </var/run/rc.httpd.run> [SYSTEM]/bin/cp -f /etc/group.smb /etc/group 2>/dev/null [SYSTEM]/bin/cp -f /etc/passwd.smb /etc/passwd 2>/dev/null [SYSTEM]/bin/cp -f /etc/samba.conf/smbpasswd /etc/samba/smbpasswd 2>/dev/null [SYSTEM]/bin/cp -f /etc/samba.conf/smb.conf /etc/samba/smb.conf 2>/dev/null [clientpacket.c::send_discover():175] Sending discover... [clientpacket.c::send_discover():175] Sending discover... username=admin,passwd=password ---------------- [SYSTEM]/usr/bin/killall -HUP nmbd [SYSTEM]/usr/sbin/nmbd -s /etc/samba/smb.conf -D -P 19 [SYSTEM]/usr/sbin/rc usb_service restart [rc debug]/usr/sbin/rc usb_service restart ap_name=usb_service action=restart [rc.c::rc_action():829] rc_action before add usb_service - restart rc action <usb_service @ restart> before file_lock. rc action <usb_service @ restart lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add usb_service - restart unlink running file </var/run/rc.usb_service.run> [rc.c::rc_action():829] rc_action before add usb_service - restart rc action <usb_service @ restart> before file_lock. rc action <usb_service @ restart lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add usb_service - restart unlink running file </var/run/rc.usb_service.run> can't find this application [rc.c::rc_action():829] rc_action before add usb_service - restart rc action <usb_service @ restart> before file_lock. rc action <usb_service @ restart lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_service.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add usb_service - restart [rc.c::rc_stop():771] Calling Stop function of usb_service [SYSTEM]/etc/mtk/mt7621_smp.sh wifi [SYSTEM]/bin/rm /etc/samba/secrets.tdb rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory [SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1 [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed [rc.c::rc_start():732] Calling Start function of usb_service [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed unlink running file </var/run/rc.usb_service.run> [rc debug]/usr/sbin/rc wifi_isolation restart ap_name=wifi_isolation action=restart [rc.c::rc_action():829] rc_action before add wifi_isolation - restart rc action <wifi_isolation @ restart> before file_lock. rc action <wifi_isolation @ restart lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add wifi_isolation - restart [rc.c::rc_stop():771] Calling Stop function of wifi_isolation [SYSTEM]/sbin/rmmod /lib/modules/wifi_isolation.ko rmmod: /lib/modules/wifi_isolation.ko: No such file or directory [rc.c::rc_start():732] Calling Start function of wifi_isolation [wifi_isolation/wifi_isolation.c::start_wifi_isolation():46] AP Mode no need wifi_isolation! unlink running file </var/run/rc.wifi_isolation.run> [SYSTEM]/usr/sbin/rc dnrd start [rc debug]/usr/sbin/rc dnrd start ap_name=dnrd action=start [rc.c::rc_action():829] rc_action before add dnrd - start rc action <dnrd @ start> before file_lock. rc action <dnrd @ start lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add dnrd - start [rc.c::rc_start():732] Calling Start function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.0.100:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.0.100 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd [SYSTEM]dnrd -a 192.168.0.100 -m hosts -c off -r 0 -s 8.8.8.8 -o 0 -q xxx& [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.0.100 unlink running file </var/run/rc.dnrd.run> [SYSTEM]/usr/sbin/rc route start [rc debug]/usr/sbin/rc route start ap_name=route action=start [rc.c::rc_action():829] rc_action before add route - start rc action <route @ start> before file_lock. rc action <route @ start lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():837] rc_action after add route - start [rc.c::rc_start():732] Calling Start function of route unlink running file </var/run/rc.route.run> [SYSTEM]/bin/killall failover killall: failover: no process killed [SYSTEM]/usr/sbin/brctl stp br0 off [SYSTEM]/usr/sbin/brctl stp br0 on sh: cannot create /proc/http_file/getLanIp: nonexistent directory unlink running file </var/run/rc.lan.run> Notice: caching turned off Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.


OpenWrt bootlog

[ 0.000000] Linux version 5.4.52 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13911-b057862e24)) #0 SMP Wed Jul 22 16:59:44 2020 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Netgear WAC104 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2} total 2 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] percpu: Embedded 14 pages/cpu s26704 r8192 d22448 u57344 [ 0.000000] pcpu-alloc: s26704 r8192 d22448 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=0004f511 [ 0.000000] Readback ErrCtl register=0004f511 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 120824K/131072K available (5853K kernel code, 207K rwdata, 1264K rodata, 1240K init, 237K bss, 10248K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x558 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.015472] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360) [ 0.055784] pid_max: default: 32768 minimum: 301 [ 0.065100] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.079498] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.097170] rcu: Hierarchical SRCU implementation. [ 0.107082] smp: Bringing up secondary CPUs ... [ 7.940426] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 7.940436] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 7.940446] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 7.940541] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.144129] Synchronize counters for CPU 1: done. [ 0.203764] smp: Brought up 1 node, 2 CPUs [ 0.215811] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.235094] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.248758] pinctrl core: initialized pinctrl subsystem [ 0.260849] NET: Registered protocol family 16 [ 0.281482] FPU Affinity set after 4688 emulations [ 0.304134] clocksource: Switched to clocksource GIC [ 0.315583] NET: Registered protocol family 2 [ 0.325274] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.341843] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.357040] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.370984] TCP: Hash tables configured (established 1024 bind 1024) [ 0.383749] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.396642] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.410707] NET: Registered protocol family 1 [ 0.419270] PCI: CLS 0 bytes, default 32 [ 0.516101] 4 CPUs re-calibrate udelay(lpj = 1163264) [ 0.527546] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.553077] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.564585] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.587410] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.603737] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.615137] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.626432] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.638268] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.654906] printk: console [ttyS0] disabled [ 0.663365] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 15, base_baud = 3125000) is a 16550A [ 0.681288] printk: console [ttyS0] enabled [ 0.697836] printk: bootconsole [early0] disabled [ 0.719732] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 0.734625] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 0.747285] nand: Macronix MX30LF1G18AC [ 0.754929] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.770015] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 0.783056] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 0.797623] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 0.812184] Scanning device for bad blocks [ 2.118867] 6 fixed-partitions partitions found on MTD device mt7621-nand [ 2.132390] Creating 6 MTD partitions on "mt7621-nand": [ 2.142804] 0x000000000000-0x000000100000 : "u-boot" [ 2.154188] 0x000000100000-0x000000200000 : "SC PID" [ 2.165548] 0x000000200000-0x000000600000 : "kernel" [ 2.176914] 0x000000600000-0x000002200000 : "ubi" [ 2.187869] 0x000002e00000-0x000002f00000 : "factory" [ 2.199394] 0x000004200000-0x000007e00000 : "reserved" [ 2.212749] libphy: Fixed MDIO Bus: probed [ 2.246825] libphy: mdio: probed [ 2.253511] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 2.267464] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 16 [ 2.286224] mt7621-pci 1e140000.pcie: Parsing DT failed [ 2.299590] NET: Registered protocol family 10 [ 2.310130] Segment Routing with IPv6 [ 2.317569] NET: Registered protocol family 17 [ 2.326493] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.352541] 8021q: 802.1Q VLAN Support v1.8 [ 2.362896] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 2.375377] random: fast init done [ 2.391588] libphy: dsa slave smi: probed [ 2.400061] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 2.418081] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 2.436050] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] [ 2.454020] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] [ 2.472328] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 2.489850] DSA: tree 0 setup [ 2.496129] rt2880-pinmux pinctrl: pcie is already enabled [ 2.507071] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back [ 2.522125] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 2.537037] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 2.651589] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 2.662707] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 2.773549] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK) [ 2.787427] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 2.797147] mt7621-pci 1e140000.pcie: PCIE2 enabled [ 2.806869] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 2.825584] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 2.838267] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 2.851966] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 2.865669] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.876639] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 2.888646] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 2.901141] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff] [ 2.913696] pci 0000:00:00.0: supports D1 [ 2.921685] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 2.933533] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 2.945550] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 2.958044] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff] [ 2.970590] pci 0000:00:01.0: supports D1 [ 2.978580] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 2.991521] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000 [ 3.003565] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 3.017132] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 3.030584] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 3.044024] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.054457] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 3.066600] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 3.080131] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 3.094530] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.107916] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000 [ 3.119942] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 3.132570] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 3.146014] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 3.156445] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 3.168588] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 3.182114] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 3.196514] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.209747] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 3.222925] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.236802] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 3.249979] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.263853] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 3.277385] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 3.291777] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 3.305315] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 3.319707] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 3.333243] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 3.346774] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 3.360306] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 3.373845] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 3.388425] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] [ 3.402815] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.412717] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 3.426244] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 3.439770] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 3.454171] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff] [ 3.467699] pci 0000:00:01.0: PCI bridge to [bus 02] [ 3.477595] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 3.491121] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 3.504650] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 3.519603] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 3.521381] UBI: auto-attach mtd3 [ 3.540031] ubi0: attaching mtd3 [ 3.831458] ubi0: scanning is finished [ 3.855258] ubi0: attached mtd3 (name "ubi", size 28 MiB) [ 3.866070] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.879765] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.893291] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.907158] ubi0: good PEBs: 224, bad PEBs: 0, corrupted PEBs: 0 [ 3.919125] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 3.933519] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1591643777 [ 3.951716] ubi0: available PEBs: 0, total reserved PEBs: 224, PEBs reserved for bad PEB handling: 20 [ 3.970118] ubi0: background thread "ubi_bgt0d" started, PID 451 [ 3.972433] block ubiblock0_0: created from ubi0:0(rootfs) [ 3.993042] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.006919] hctosys: unable to open rtc device (rtc0) [ 4.023315] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 4.041948] Freeing unused kernel memory: 1240K [ 4.051002] This architecture does not have kernel memory protection. [ 4.063829] Run /sbin/init as init process [ 4.544069] init: Console is alive [ 4.551154] init: - watchdog - [ 5.207697] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.309441] usbcore: registered new interface driver usbfs [ 5.320511] usbcore: registered new interface driver hub [ 5.331260] usbcore: registered new device driver usb [ 5.355753] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.372492] init: - preinit - [ 6.042433] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 6.058489] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 6.075822] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.264368] random: jshn: uninitialized urandom read (4 bytes read) [ 6.379470] random: jshn: uninitialized urandom read (4 bytes read) [ 6.415089] random: jshn: uninitialized urandom read (4 bytes read) [ 6.549831] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 6.563413] 8021q: adding VLAN 0 to HW filter on device lan1 [ 10.668727] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off [ 10.683380] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 10.842105] UBIFS (ubi0:1): default file-system created [ 10.853986] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 10.865512] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 571 [ 10.993002] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 11.008637] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 11.028394] UBIFS (ubi0:1): FS size: 21585920 bytes (20 MiB, 170 LEBs), journal size 1142784 bytes (1 MiB, 9 LEBs) [ 11.049013] UBIFS (ubi0:1): reserved for root: 1019556 bytes (995 KiB) [ 11.062032] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 35604354-0576-4CB2-964D-1A297A28DDC4, small LPT model [ 11.087590] mount_root: overlay filesystem has not been fully initialized yet [ 11.102280] mount_root: switching to ubifs overlay [ 11.126024] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 11.147133] urandom-seed: Seed file not found (/etc/urandom.seed) [ 11.181226] mt7530 mdio-bus:1f lan1: Link is Down [ 11.200400] procd: - early - [ 11.206248] procd: - watchdog - [ 11.768261] procd: - watchdog - [ 11.774850] procd: - ubus - [ 11.824438] urandom_read: 5 callbacks suppressed [ 11.824449] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.895150] random: ubusd: uninitialized urandom read (4 bytes read) [ 11.909472] procd: - init - [ 12.454786] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.487165] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056 [ 12.502307] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb [ 12.541600] xt_time: kernel timezone is -0000 [ 12.637600] urngd: v1.0.2 started. [ 12.703246] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=20 [ 12.714107] pci 0000:00:01.0: enabling device (0006 -> 0007) [ 12.725407] mt7603e 0000:02:00.0: enabling device (0000 -> 0002) [ 12.737574] mt7603e 0000:02:00.0: ASIC revision: 76030010 [ 12.828008] random: crng init done [ 13.369496] mt7603e 0000:02:00.0: Firmware Version: ap_pcie [ 13.380632] mt7603e 0000:02:00.0: Build Time: 20160107100755 [ 13.416129] mt7603e 0000:02:00.0: firmware init done [ 13.601516] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 13.685251] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=18 [ 13.696065] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 13.707369] mt76x2e 0000:01:00.0: enabling device (0000 -> 0002) [ 13.719582] mt76x2e 0000:01:00.0: ASIC revision: 76120044 [ 14.298644] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a [ 14.314612] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00 [ 14.325564] mt76x2e 0000:01:00.0: Build: 1 [ 14.333728] mt76x2e 0000:01:00.0: Build Time: 201507311614____ [ 14.360118] mt76x2e 0000:01:00.0: Firmware running! [ 14.371682] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 14.397806] PPP generic driver version 2.4.2 [ 14.410039] NET: Registered protocol family 24 [ 14.437673] kmodloader: done loading kernel modules from /etc/modules.d/* [ 37.890633] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 37.910163] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 37.926604] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 37.946597] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 37.965282] 8021q: adding VLAN 0 to HW filter on device lan1 [ 37.980519] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 37.994299] br-lan: port 1(lan1) entered blocking state [ 38.005080] br-lan: port 1(lan1) entered disabled state [ 38.017883] device lan1 entered promiscuous mode [ 38.027225] device eth0 entered promiscuous mode [ 38.059929] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 38.073871] 8021q: adding VLAN 0 to HW filter on device lan2 [ 38.088706] br-lan: port 2(lan2) entered blocking state [ 38.099212] br-lan: port 2(lan2) entered disabled state [ 38.111049] device lan2 entered promiscuous mode [ 38.128772] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 38.143672] 8021q: adding VLAN 0 to HW filter on device lan3 [ 38.158925] br-lan: port 3(lan3) entered blocking state [ 38.169454] br-lan: port 3(lan3) entered disabled state [ 38.183728] device lan3 entered promiscuous mode [ 38.201850] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 38.217433] 8021q: adding VLAN 0 to HW filter on device lan4 [ 38.232434] br-lan: port 4(lan4) entered blocking state [ 38.242961] br-lan: port 4(lan4) entered disabled state [ 38.255220] device lan4 entered promiscuous mode [ 42.060625] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control off [ 42.075261] br-lan: port 1(lan1) entered blocking state [ 42.085714] br-lan: port 1(lan1) entered forwarding state [ 42.097399] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Notes

Space for additional notes, links to forum threads or other resources.

  • Please look R6220 wikipage: Netgear R6220. Many info fit to to WAC104.

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/netgear/netgear_wac104.txt · Last modified: 2020/07/23 05:55 by tmomas