User Tools

Site Tools


toh:netgear:dgnd3700v2

Netgear DGND3700 v2

Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when chosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom WiFi for details.

DSL will not work at all on devices with BCM63xx DSL chipset (due to unavailability of FLOSS driver for Broadcom chips). Consider this when chosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported.
See Broadcom DSL, Unsupported: DSL modem and Broadcom BCM63xx for details.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
DGND3700v2Broadcom BCM63624003264Broadcom BCM6361, Broadcom BCM43228 (mini-PCIe)b/g/na/n-5ADSL2+2x 2.0

Installation

Installation via CFE web (http) server

The RESET button only works in this router for sending an unkown Sercomm image via an unknown transfer procedure.

We will use the serial port TX-RX shortcircuit trick (or a serial TTL adapter) for entering into CFE's standard web interface recovery:

  1. Set a static IP on your computer, use 192.168.1.35 (or any compatible), and connect the ethernet cable to the router.
  2. Unplug the router's power cord
  3. Shortcircuit TX and RX serial pins (this will simulate keyboard buttons pressing on the serial port; ugly but it should work)
  4. Plug the router's power cord and wait 3 or more seconds
  5. Remove the TX-RX shortcircuit.
  6. Browse to http://192.168.1.1, you should see this screen:
  7. Send the new firmware and wait some minutes until the firmware upgrade finish.
  8. ssh to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

It's also possible to attach a serial console (UART 3.3V TTL adapter required). Press any key at the console when starting up the router to break into CFE CLI.

OEM flash layout

dev:    size   erasesize  name
mtd0: 01ac0000 00004000 "rootfs"
mtd1: 00004000 00004000 "nvram"
mtd2: 00040000 00004000 "language_DEU"
mtd3: 00100000 00004000 "scnvram"
mtd4: 00040000 00004000 "factory"
mtd5: 01c40000 00004000 "upgrade"
mtd6: 00040000 00004000 "flag"
mtd7: 00040000 00004000 "pcbasn"
mtd8: 00080000 00004000 "xxx"
mtd9: 00040000 00004000 "language_PTB"
mtd10: 00040000 00004000 "language_RUS"
mtd11: 00040000 00004000 "language_CHS"
mtd12: 00040000 00004000 "language_ENU"
mtd13: 00040000 00004000 "language_dev"

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Use a serial TTL adapter to connect your PC with the router. Only connect TX, RX and GND.

Settings:

  • Baudrate: 115200
  • Data bits: 8
  • Parity: None
  • Stop bits: 1

The serial port is located at the Jumper J302 on the board:

1 2 3 4 J302 GND TX VCC RX

Only connect GND, TX and RX. (Never connect VCC, you may damage the board otherwise)

Serial flashing how-to: External Link

OEM Bootlog

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS ZQDN PHYE DINT LASY USYN MSYN LMBE PASS ---- ZBSS CODE DATA L12F MAIN NAN0 BTam 0001 NAN9 NAN3 RFS0 NAN5 CFE version 1.0.38-112.14 for BCM96362 (32bit,SP,BE) Build Date: 2011年 12月 21日 星期三 18:16:05 CST (sunny@localhost) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name <not identified>, id 0x2075 block 16KB size 32768KB External switch id = 53125 SC Debug: Setting RGMII TX_CLK DELAY at SWITCH IMP PORT! SC Debug: Setting RGMII RX_CLK DELAY at SWITCH IMP PORT! Chip ID: BCM6362B0, MIPS: 400MHz, DDR: 333MHz, Bus: 166MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-5) : 96362ADVN2xh Number of MAC Addresses (1-32) : 11 Base MAC Address : 4c:60:de:**:**:** PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Enter NMRP_main Scanning Flash Section 0... Scanning Flash Section 1... Scanning Flash Section 2... Scanning Flash Section 3... Scanning Flash Section 4... Scanning Flash Section 5... Scanning Flash Section 6... Scanning Flash Section 7... Scanning Flash Section 8... Scanning Flash Section 9... Scanning Flash Section 10... Scanning Flash Section 11... Scanning Flash Section 12... NMRP:LISTENING ### No NMRP Server found ### Scanning Flash Section 0... Scanning Flash Section 1... Scanning Flash Section 2... Scanning Flash Section 3... Scanning Flash Section 4... Scanning Flash Section 5... Scanning Flash Section 6... Scanning Flash Section 7... Scanning Flash Section 8... Scanning Flash Section 9... Scanning Flash Section 10... Scanning Flash Section 11... Scanning Flash Section 12... *************************************************** Sercomm Boot Version 1...0.6 *************************************************** 0 Block in Flag Section Find Sercomm Sign! Entering Firmware : Everything is OK. Booting from Primary image (0xb8080000) ... Decompression OK! Entry at 0x8033ffb0 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x8033ffb0 Linux version 2.6.30 (root@BuildServer) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Fri Jun 29 13:48:25 CST 2012 BCM Flash API. Flash device is not found. 96362ADVN2xh prom init CPU revision is: 0002a070 (Broadcom4350) DSL SDRAM reserved: 0x100000 Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003f00 On node 0 totalpages: 16128 free_area_init_node: node 0, pgdat 80416520, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 59276k/64512k available (3296k kernel code, 5216k reserved, 841k data, 160k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Jun 29 2012 13:42:42 CPU revision is: 0002a070 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 1140 bytes NET: Registered protocol family 16 Total Flash size: 0K with -1 sectors registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff] pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff] pci 0000:02:00.0: supports D1 D2 pci 0000:02:00.0: PME# supported from D0 D3hot D3cold pci 0000:02:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff pci 0000:01:00.0: PREFETCH window: disabled PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Jun 29 2012 13:46:48 initialized Broadcom GBPM v0.1 Jun 29 2012 13:46:48 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 115 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 Failed to read image tag from flash Broadcom DSL NAND controller (BrcmNand Controller) -->brcmnand_scan: CS=0, numchips=1, csi=0 mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=03032200, chipSelect=0 brcmnand_read_id: CS0: dev_id=20752075 After: NandSelect=40000001, nandConfig=03032200 Block size=00004000, erase shift=14 NAND Config: Reg=03032200, chipSize=32 MB, blockSize=16K, erase_shift=e busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff timing1 not adjusted: 5363444f timing2 not adjusted: 00000fc6 BrcmNAND mfg 20 75 ST ST_NAND256W3A 32MB on CS0 Found NAND on CS0: ACC=f3000000, cfg=03032200, flashId=20752075, tim1=5363444f, tim2=00000fc6 BrcmNAND version = 0x0202 32MB @00000000 B4: NandSelect=40000001, nandConfig=03032200, chipSelect=0 brcmnand_read_id: CS0: dev_id=20752075 After: NandSelect=40000001, nandConfig=03032200 Found NAND flash on Chip Select 0, chipSize=32MB, usable size=32MB, base=0 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f3000000 page_shift=9, bbt_erase_shift=14, chip_shift=25, phys_erase_shift=14 brcmnand_scan 220 Brcm NAND controller version = 2.2 NAND flash size 32MB @1e000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=16, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=16, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 brcmnand_scan: mtd->oobsize=16 brcmnand_scan: oobavail=12, eccsize=512, writesize=512 brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=83a3ed90, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffe0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0000ffc0, version 0x01 for chip on CS0 brcmnandCET: Status -> Deferred brcmnand_scan 99 Creating 14 MTD partitions on "brcmnand.0": 0x000000080000-0x000001b40000 : "rootfs" 0x000000000000-0x000000004000 : "nvram" 0x000001b40000-0x000001b80000 : "language_DEU" 0x000001dc0000-0x000001ec0000 : "scnvram" 0x000001ec0000-0x000001f00000 : "factory" 0x000000080000-0x000001cc0000 : "upgrade" 0x000001c80000-0x000001cc0000 : "flag" 0x000001cc0000-0x000001d00000 : "pcbasn" 0x000001d00000-0x000001d80000 : "xxx" 0x000001b80000-0x000001bc0000 : "language_PTB" 0x000001bc0000-0x000001c00000 : "language_RUS" 0x000001c00000-0x000001c40000 : "language_CHS" 0x000001c40000-0x000001c80000 : "language_ENU" 0x000001d80000-0x000001dc0000 : "language_dev" usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry kerSysScreenPciDevices: 0x14e4:0x435f:(slot 0) detected kerSysScreenPciDevices: 0x14e4:0x6300:(slot 9) detected kerSysScreenPciDevices: 0x14e4:0x6300:(slot 10) detected kerSysScreenPciDevices: 0x14e4:0x6362:(slot 0) detected kerSysScreenPciDevices: 0x14e4:0x4359:(slot 0) detected SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0xc00f is enabled Serial: BCM63XX driver $Revision: 3.00 $ Magic SysRq enabled (type ^ h for list of supported commands) ttyS0 at MMIO 0xb0000100 (irq = 11) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 12) is a BCM63XX bcmPktDma_init: Broadcom Packet DMA Library initialized Total # RxBds=1808 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmxtmrt: Broadcom BCM6362B0 ATM/PTM Network Device v0.3 Jun 29 2012 13:45:55 IPSEC SPU: SUCCEEDED GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1008 buckets, 4032 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 160k freed init started: BusyBox v1.13.4 (2012-06-29 14:02:50 CST) starting pid 257, tty '/dev/console': '/usr/etc/rcS' cp: cannot create '/dev/pts/0': Operation not permitted cp: cannot create '/dev/pts/1': Operation not permitted ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected bcm_ingqos: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Broadcom Ingress QoS Module Char Driver v0.1 Jun 29 2012 13:45:09 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066329B (9MB), num of buffers=4802, buf size=2096 Broadcom BPM Module Char Driver v0.1 Jun 29 2012 13:44:49 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled  NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Jun 29 2012 13:45:10 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Jun 29 2012 13:45:10 chipId 0x636220B0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Jun 29 2012 13:44:51 Registered <241> FAP Debug values at 0x00000010 0x00000010 Enabling SMISBUS PHYS_FAP_BASE[0] is 0x14001000 FAP Soft Reset Done 4ke Reset Done Allocated FAP0 GSO Buffers (0xA2B98458) : 1048576 bytes @ 0xA2400000 [NTC fapProto] fapReset : Reset FAP Protocol layer [FAP0] DSPRAM : stack <0x80004000><1024>, global <0x80004400><7152>, free <16>, total<8192> [FAP0] PSM : addr<0xE0010000>, used <32720>, free <48>, total <32768> [FAP0] Flows supported: 128 (dsp 85, psm 43, qsm 0) [FAP0] DQM : availableMemory 14068 bytes, nextByteAddress 0xE000490C [FAP0] GSO Buffer set to 0xA2400000 [FAP0] FAP BPM Initialized. bcmPktDma_bind: FAP Driver binding successfull bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6362B0 Ethernet Network Device v0.1 Jun 29 2012 13:45:42 fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b10106f0 bytes remaining 7008 ETH Init: Ch:0 - 200 tx BDs at 0xb10106f0 ETH Init: Ch:1 - 200 tx BDs at 0xa309c000 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b1011690 bytes remaining 2192 ETH Init: Ch:0 - 600 rx BDs at 0xb1011690 ETH Init: Ch:1 - 960 rx BDs at 0xa2bf4000 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth0: MAC Address: 4C:60:DE:**:**:** eth1: MAC Address: 4C:60:DE:**:**:** eth2: MAC Address: 4C:60:DE:**:**:** eth3: MAC Address: 4C:60:DE:**:**:** eth4: MAC Address: 4C:60:DE:**:**:** [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Adress Resolution Logic Processor (ARL) Char Driver v0.1 Jun 29 2012 13:44:49 Registered <245> Broadcom 802.1Q VLAN Interface, v0.1 <main 38>eth4 set switch wan port enable success netfilter dnshj choose interested dns queries module loaded ! ip6_tables: (C) 2000-2006 Netfilter Core Team init common module successful insert firewall block module success fake source dos protect modules is inserted netfilter PSD and TCP/UDP Echo/Chargen Attack loaded netfilter tcp syn flood module loaded netfilter clamp total session for one src ip module loaded netfilter other dos module loaded insmod finish Note: Loading 6300 MDK (default) driver for 6362 chip Note: Forcing 53115 driver for 53125 Switch MDK: num_switches = 2 Switch MDK: unit = 0; phy_pbmp = 0x0; config_pbmp = 0x10 Zeroluo Enable RGMII tx clock delay mode in bcm53115_a0_bmd_init chip/bcm53115_a0/bcm53115_a0_bmd_init.c Switch MDK link poll thread: unit=1; phypbmp=0x1f Initializing unit 0 in unmanaged mode jffs2_scan_inode_node(): CRC failed on node at 0x000597e8: Read 0xffffffff, calculated 0xaab3f958 Empty flash at 0x0005982c ends at 0x00059a00 jffs2_scan_inode_node(): CRC failed on node at 0x000f93c0: Read 0xffffffff, calculated 0xcaf1405e =============mount finished RC: wifi_init() lan mac: 0x00:0x00:0x00:0x00:0x2a:0xab !!! =============rc start =============rc finish rcd: enQ=/usr/sbin/rc_app/rc_start rcd: [run] deQ =/usr/sbin/rc_app/rc_start PID USER VSZ STAT COMMAND 1 root 1012 S init 2 root 0 SW< [kthreadd] 3 root 0 SW< [migration/0] 4 root 0 SW [sirq-high/0] 5 root 0 SW [sirq-timer/0] 6 root 0 SW [sirq-net-tx/0] 7 root 0 SW [sirq-net-rx/0] 8 root 0 SW [sirq-block/0] 9 root 0 SW [sirq-tasklet/0] 10 root 0 SW [sirq-sched/0] 11 root 0 SW [sirq-hrtimer/0] 12 root 0 SW [sirq-rcu/0] 13 root 0 SW< [migration/1] 14 root 0 SW [sirq-high/1] 15 root 0 SW [sirq-timer/1] 16 root 0 SW [sirq-net-tx/1] 17 root 0 SW [sirq-net-rx/1] 18 root 0 SW [sirq-block/1] 19 root 0 SW [sirq-tasklet/1] 20 root 0 SW [sirq-sched/1] 21 root 0 SW [sirq-hrtimer/1] 22 root 0 SW [sirq-rcu/1] 23 root 0 SW< [events/0] 24 root 0 SW< [events/1] 25 root 0 SW< [khelper] 28 root 0 SW< [async/mgr] 92 root 0 SW< [kblockd/0] 93 root 0 SW< [kblockd/1] 102 root 0 SW< [khubd] 120 root 0 SW< [bpm] 136 root 0 SW [pdflush] 137 root 0 SW [pdflush] 138 root 0 SWN [kswapd0] 140 root 0 SW< [crypto/0] 141 root 0 SW< [crypto/1] 198 root 0 SW< [mtdblockd] 246 root 0 SW [board-timer] 250 root 0 SW< [linkwatch] 257 root 1024 S /bin/sh /usr/etc/rcS 305 root 0 SW [kpAliveWatchdog] 311 root 0 SW [dsl0] 320 root 0 SW [bcmsw] 321 root 0 SW [bcmsw_timer] 394 root 1488 S /usr/sbin/swmdk 396 root 1488 S /usr/sbin/swmdk 397 root 1488 S /usr/sbin/swmdk 402 root 1224 S /sbin/klogd 404 root 800 S /usr/sbin/cmd_agent_ap rcd: enQ=/usr/sbin/rc_app/rc_syslogd start 406 root 0 SWN [jffs2_gcd_mtd4] 407 root 0 SWN [jffs2_gcd_mtd3] 408 root 0 SWN [jffs2_gcd_mtd12] 409 root 0 SWN [jffs2_gcd_mtd11] 410 root 0 SWN [jffs2_gcd_mtd10] 411 root 0 SWN [jffs2_gcd_mtd9] 412 root 0 SWN [jffs2_gcd_mtd2] 413 root 0 SWN [jffs2_gcd_mtd8] 419 root 884 S /usr/sbin/ft_tool 425 root 808 S /usr/sbin/rcd 427 root 2288 R /usr/sbin/rc_app/rc_start 428 root 1016 R /bin/ps 430 root 976 S /sbin/lan_monitor 431 root 0 Z [sh] 432 root 0 [] 433 root 0 [] rcd: enQ=/usr/sbin/rc_app/rc_upnp start rcd: enQ=/usr/sbin/rc_app/rc_lan init rcd: enQ=/usr/sbin/rc_app/rc_firewall init wlevt_init@232: opened loopback socket 3 wlevt is ready for new msg... wps_led_idle entering route: SIOCADDRT: No such device rcd: enQ=/usr/sbin/rc_app/rc_vlan start /usr/etc/rcS: line 234: can't create /proc/sys/net/ipv4/conf/br0/forwarding: nonexistent directory /usr/etc/rcS: line 235: can't create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory /usr/etc/rcS: line 236: can't create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory rcd: enQ=/usr/sbin/rc_app/rc_lan start rcd: enQ=/usr/sbin/rc_app/rc_lan reset_switch rcd: enQ=/usr/sbin/rc_app/rc_wlan start rcd: enQ=/usr/sbin/rc_app/rc_wifi_isolation start rcd: enQ=/usr/sbin/rc_app/rc_timezone start rcd: enQ=/usr/sbin/rc_app/rc_sip_alg start rcd: enQ=/usr/sbin/rc_app/rc_dnrd start rcd: enQ=/usr/sbin/rc_app/rc_httpd start rcd: enQ=/usr/sbin/rc_app/rc_printk start rcd: enQ=/usr/sbin/rc_app/rc_ddns init rcd: enQ=/usr/sbin/rc_app/rc_check_conn start rcd: enQ=/usr/sbin/rc_app/rc_wan init rcd: enQ=/usr/sbin/rc_app/rc_route start rcd: enQ=/usr/sbin/rc_app/rc_ripd start rcd: enQ=/usr/sbin/rc_app/rc_potcounter start rcd: enQ=/usr/sbin/rc_app/rc_lltd start rcd: enQ=/usr/sbin/rc_app/rc_upnp start rcd: enQ=/usr/sbin/rc_app/rc_schedule start rcd: enQ=/usr/sbin/rc_app/rc_usb_service init rcd: enQ=/usr/sbin/rc_app/rc_start finished rcd: [run] deQ =/usr/sbin/rc_app/rc_syslogd start rcd: [run] deQ =/usr/sbin/rc_app/rc_upnp start killall: miniupnpd: no process killed route: SIOCADDRT: No such device rcd: [run] deQ =/usr/sbin/rc_app/rc_lan init rcd: [run] deQ =/usr/sbin/rc_app/rc_firewall init [ firewall_main - 126 ] : before fw_exe [ firewall_main - 129 ] : end fw_exe rcd: [run] deQ =/usr/sbin/rc_app/rc_vlan start rcd: an error occurred in execvp rcd: [run] deQ =/usr/sbin/rc_app/rc_lan start ADDRCONF(NETDEV_UP): eth0: link is not ready ADDRCONF(NETDEV_UP): eth1: link is not ready ADDRCONF(NETDEV_UP): eth2: link is not ready ADDRCONF(NETDEV_UP): eth3: link is not ready device eth0 entered promiscuous mode device eth1 entered promiscuous mode device eth2 entered promiscuous mode device eth3 entered promiscuous mode killall: udhcpd_1: no process killed [ firewall_main - 126 ] : before fw_exe rcd: enQ=/usr/sbin/rc_app/rc_schedule restart [ firewall_main - 129 ] : end fw_exe rcd: [run] deQ =/usr/sbin/rc_app/rc_lan reset_switch rcd: [run] deQ =/usr/sbin/rc_app/rc_wlan start lan_device[1] = wl [1]lan_device[1] = wl [2]lan_device[1] = wl [3]lan_device[1] = wl [4]/sbin/wl: wl driver adapter not found RC: insert wl.ko... --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=3121 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=256 otp_read_pci: bad crc Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_vars.bin Failed to open srom image from '/etc/wlan/bcm6362_vars.bin'. wl:loading /etc/wlan/bcm6362_map.bin wl0: Broadcom BCM435f 802.11 Wireless Controller 5.100.138.2001.cpe4.12L04.3 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered PCI: Enabling device 0000:02:00.0 (0000 -> 0002) wl: passivemode=1 wl: napimode=0 wl1: allocskbmode=1 currallocskbsz=500 wl1: Broadcom BCM4359 802.11 Wireless Controller 5.100.138.2001.cpe4.12L04.3 dgasp: kerSysRegisterDyingGaspHandler: wl1 registered lan_ifnames=eth0 wl0 wl1 wl0.1 wl0.2 wl0.3 wl1.1 wl1.2 wl1.3 lan1_ifnames= ========idx=0 /sbin/wl -i wl0 phy_watchdog 0 /sbin/wl -i wl0 up /sbin/wl -i wl0 down /sbin/wl -i wl0 wds none /sbin/wl -i wl0 mbss 0 /sbin/wl -i wl0 bss -C 0 down /sbin/wl -i wl0 bss -C 1 down /sbin/wl -i wl0 bss -C 2 down /sbin/wl -i wl0 bss -C 3 down /sbin/wl -i wl0 ssid -C 0 "NETGEAR55" Setting SSID: "NETGEAR55" /sbin/wl -i wl0 ssid -C 1 "NETGEAR-Guest" Setting SSID: "NETGEAR-Guest" /sbin/wl -i wl0 ssid -C 2 "NETGEAR-Guest2" Setting SSID: "NETGEAR-Guest2" /sbin/wl -i wl0 ssid -C 3 "NETGEAR-Guest3" Setting SSID: "NETGEAR-Guest3" /sbin/ifconfig wl0 down 2>/dev/null /sbin/ifconfig wl0.1 down 2>/dev/null /sbin/ifconfig wl0.2 down 2>/dev/null /sbin/ifconfig wl0.3 down 2>/dev/null /sbin/ifconfig wl0 hw ether 4C:60:DE:**:**:** 2>/dev/null /sbin/wl -i wl0 cur_etheraddr 4C:60:DE:**:**:** 2>/dev/null /sbin/ifconfig wl0.1 hw ether 6a:60:DE:**:**:fb 2>/dev/null /sbin/wl -i wl0.1 cur_etheraddr 6a:60:DE:**:**:fb 2>/dev/null /sbin/ifconfig wl0.2 hw ether 6a:60:DE:**:**:f8 2>/dev/null /sbin/wl -i wl0.2 cur_etheraddr 6a:60:DE:**:**:f8 2>/dev/null /sbin/ifconfig wl0.3 hw ether 6a:60:DE:**:**:f9 2>/dev/null /sbin/wl -i wl0.3 cur_etheraddr 6a:60:DE:**:**:f9 2>/dev/null /sbin/wl -i wl0 ap 1 /sbin/wl -i wl0 infra 1 /sbin/wl -i wl0 closed 0 /sbin/wl -i wl0 country US /sbin/wl -i wl0 band b /sbin/wl -i wl0 regulatory 0 /sbin/wl -i wl0 radar 0 2>/dev/null /sbin/wl -i wl0 spect 0 2>/dev/null /sbin/wl -i wl0 nmode -1 /sbin/wl -i wl0 mimo_bw_cap 0 /sbin/wl -i wl0 wpa_cap -C 0 > /var/wpa_cap0 /sbin/wl -i wl0 wpa_cap -C 0 0 2>/dev/null /sbin/wl -i wl0 wpa_cap -C 1 > /var/wpa_cap0 /sbin/wl -i wl0 wpa_cap -C 1 0 2>/dev/null /sbin/wl -i wl0 wpa_cap -C 2 > /var/wpa_cap0 /sbin/wl -i wl0 wpa_cap -C 2 0 2>/dev/null /sbin/wl -i wl0 wpa_cap -C 3 > /var/wpa_cap0 /sbin/wl -i wl0 wpa_cap -C 3 0 2>/dev/null /sbin/wl -i wl0 maxassoc 16 /sbin/wl -i wl0 bss_maxassoc 16 /sbin/wl -i wl0 gmode Auto /sbin/wl -i wl0 gmode_protection_override -1 /sbin/wl -i wl0 gmode_protection_control 2 /sbin/wl -i wl0 nmode_protection_override -1 /sbin/wl -i wl0 protection_control 2 /sbin/wl -i wl0 protection_control 2 /sbin/wl -i wl0 rifs_advert 0 /sbin/wl -i wl0 obss_coex 0 /sbin/wl -i wl0 stbc_tx -1 /sbin/wl -i wl0 stbc_rx 1 /sbin/wl -i wl0 nreqd 0 /sbin/wl -i wl0 wme 0 2>/dev/null /sbin/wl -i wl0 afterburner_override 0 2>/dev/null /sbin/wl -i wl0 ampdu 1 /sbin/wl -i wl0 afterburner_override 0 /sbin/wl -i wl0 afterburner_override 0 /sbin/wl -i wl0 wme 1 2>/dev/null /sbin/wl -i wl0 wme_noack 0 2>/dev/null /sbin/wl -i wl0 wme_apsd 1 2>/dev/null /sbin/wl -i wl0 wme_bss_disable 0 /sbin/wl -i wl0 plcphdr long /sbin/wl -i wl0 bands > /var/wl0bands /sbin/wl -i wl0 rate 0 /sbin/wl -i wl0 a_rate 0 /sbin/wl -i wl0 bg_rate 0 /sbin/wl leddc 0x0 /sbin/wl -i wl0 mrate -1 /sbin/wl -i wl0 a_mrate -1 /sbin/wl -i wl0 bg_mrate -1 /sbin/wl -i wl0 rtsthresh 2347 /sbin/wl -i wl0 fragthresh 2346 /sbin/wl -i wl0 dtim 2 /sbin/wl -i wl0 bi 100 /sbin/wl -i wl0 bcn_rotate 1 /sbin/wl -i wl0 frameburst 1 /sbin/wl -i wl0 ap_isolate 0 /sbin/wl -i wl0 pwr_percent 100 /sbin/wl -i wl0 wmf_bss_enable 0 /sbin/wl -i wl0.1 wmf_bss_enable 0 /sbin/wl -i wl0.2 wmf_bss_enable 0 /sbin/wl -i wl0.3 wmf_bss_enable 0 /sbin/wl -i wl0 chanim_mode 1 /sbin/wl -i wl0 rxchain_pwrsave_stas_assoc_check 1 /sbin/wl -i wl0 rxchain_pwrsave_enable 0 /sbin/wl -i wl0 rxchain_pwrsave_quiet_time 10 /sbin/wl -i wl0 rxchain_pwrsave_pps 10 /sbin/wl -i wl0 radio_pwrsave_enable 0 /sbin/wl: Not Permitted /sbin/wl -i wl0 radio_pwrsave_quiet_time 10 /sbin/wl -i wl0 radio_pwrsave_pps 1 /sbin/wl -i wl0 radio_pwrsave_level 0 /sbin/wl -i wl0 mac none /sbin/wl -i wl0 macmode 0 /sbin/wl -i wl0 up /sbin/wl -i wl0 autochannel 1 chanspec 0x2b06 selected /sbin/wl -i wl0 autochannel 2 /sbin/wl -i wl0 csscantimer 0 /sbin/wl -i wl0 obss_coex 0 /sbin/wl -i wl0 rmwep -C 0 0 /sbin/wl -i wl0 rmwep -C 0 1 /sbin/wl -i wl0 rmwep -C 0 2 /sbin/wl -i wl0 rmwep -C 0 3 /sbin/wl -i wl0 rmwep -C 1 0 /sbin/wl -i wl0 rmwep -C 1 1 /sbin/wl -i wl0 rmwep -C 1 2 /sbin/wl -i wl0 rmwep -C 1 3 /sbin/wl -i wl0 rmwep -C 2 0 /sbin/wl -i wl0 rmwep -C 2 1 /sbin/wl -i wl0 rmwep -C 2 2 /sbin/wl -i wl0 rmwep -C 2 3 /sbin/wl -i wl0 rmwep -C 3 0 /sbin/wl -i wl0 rmwep -C 3 1 /sbin/wl -i wl0 rmwep -C 3 2 /sbin/wl -i wl0 rmwep -C 3 3 /sbin/wl -i wl0 wsec -C 0 4 /sbin/wl -i wl0 wsec_restrict -C 0 1 /sbin/wl -i wl0 wpa_auth -C 0 128 /sbin/wl -i wl0 eap 1 /sbin/wl -i wl0 auth -C 0 0 /sbin/wl -i wl0 wdswsec 0 /sbin/wl -i wl0 wdswsec_enable 0 /usr/sbin/brctl addif group1 wl0 device wl0 entered promiscuous mode ifconfig: wl1.1: error fetching interface information: Device not found ifconfig: wl1.1: error fetching interface information: Device not found ifconfig: wl1.2: error fetching interface information: Device not found ifconfig: wl1.2: error fetching interface information: Device not found ifconfig: wl1.3: error fetching interface information: Device not found ifconfig: wl1.3: error fetching interface information: Device not found sh: /bin/igd: not found setting oob: lan_wps_oob wps_cfg_state = 1, wps_config=ap-er wscLedSet: led_action 0, led_blink_type 0, led_event 0, led_status 0 wscLedSet: led_action 0, led_blink_type 0, led_event 0, led_status 0 killall: wps_det: no process killed issueServiceCmd SET dddddd wps_config=ap-er /sbin/wl -i wl0 bss -C 0 up /sbin/ifconfig wl0 up group1: port 5(wl0) entering learning state /sbin/ifconfig wl0.1 down /sbin/ifconfig wl0.2 down /sbin/ifconfig wl0.3 down /sbin/wl -i wl0 lazywds 0 /sbin/wl -i wl0 wds /sbin/wl -i wl0 wdstimeout 1 /sbin/wl -i wl0 phy_watchdog 1 /sbin/wl -i wl0 phycal_override_on_traffic 0 /sbin/wl -i wl0 fcache 1 /usr/sbin/sendarp -s group1 -d group1 setupAll end /sbin/wl -i wl0 rxchain_pwrsave_enable 0 /sbin/wl -i wl1 rxchain_pwrsave_enable 0 ========idx=1 /sbin/wl -i wl1 phy_watchdog 0 /sbin/wl -i wl1 up /sbin/wl -i wl1 down /sbin/wl -i wl1 wds none /sbin/wl -i wl1 mbss 0 /sbin/wl -i wl1 bss -C 0 down /sbin/wl -i wl1 bss -C 1 down /sbin/wl -i wl1 bss -C 2 down /sbin/wl -i wl1 bss -C 3 down /sbin/wl -i wl1 ssid -C 0 "NETGEAR55-5G" Setting SSID: "NETGEAR55-5G" /sbin/wl -i wl1 ssid -C 1 "NETGEAR-5G-Guest" Setting SSID: "NETGEAR-5G-Guest" /sbin/wl -i wl1 ssid -C 2 "NETGEAR-5G-Guest2" Setting SSID: "NETGEAR-5G-Guest2" /sbin/wl -i wl1 ssid -C 3 "NETGEAR-5G-Guest3" Setting SSID: "NETGEAR-5G-Guest3" /sbin/ifconfig wl1 down 2>/dev/null /sbin/ifconfig wl1.1 down 2>/dev/null /sbin/ifconfig wl1.2 down 2>/dev/null /sbin/ifconfig wl1.3 down 2>/dev/null wscLedSet: led_action 0, led_blink_type 0, led_event 0, led_status 0 /sbin/ifconfig wl1 hw ether 4C:60:DE:**:**:fb 2>/dev/null /sbin/wl -i wl1 cur_etheraddr 4C:60:DE:**:**:fb 2>/dev/null /sbin/ifconfig wl1.1 hw ether 72:60:DE:**:**:f8 2>/dev/null /sbin/wl -i wl1.1 cur_etheraddr 72:60:DE:**:**:f8 2>/dev/null /sbin/ifconfig wl1.2 hw ether 72:60:DE:**:**:f9 2>/dev/null /sbin/wl -i wl1.2 cur_etheraddr 72:60:DE:**:**:f9 2>/dev/null /sbin/ifconfig wl1.3 hw ether 72:60:DE:**:**:** 2>/dev/null /sbin/wl -i wl1.3 cur_etheraddr 72:60:DE:**:**:** 2>/dev/null /sbin/wl -i wl1 ap 1 group1: port 5(wl0) entering forwarding state /sbin/wl -i wl1 infra 1 /sbin/wl -i wl1 closed 0 /sbin/wl -i wl1 country US /sbin/wl -i wl1 band a /sbin/wl -i wl1 regulatory 0 /sbin/wl -i wl1 radar 0 2>/dev/null /sbin/wl -i wl1 spect 0 2>/dev/null /sbin/wl -i wl1 nmode -1 /sbin/wl -i wl1 mimo_bw_cap 1 /sbin/wl -i wl1 chanspec -c 38 -b 5 -w 40 -s -1 Chanspec set to 0x1d26 /sbin/wl -i wl1 wpa_cap -C 0 > /var/wpa_cap1 /sbin/wl -i wl1 wpa_cap -C 0 0 2>/dev/null /sbin/wl -i wl1 wpa_cap -C 1 > /var/wpa_cap1 /sbin/wl -i wl1 wpa_cap -C 1 0 2>/dev/null /sbin/wl -i wl1 wpa_cap -C 2 > /var/wpa_cap1 /sbin/wl -i wl1 wpa_cap -C 2 0 2>/dev/null /sbin/wl -i wl1 wpa_cap -C 3 > /var/wpa_cap1 /sbin/wl -i wl1 wpa_cap -C 3 0 2>/dev/null /sbin/wl -i wl1 maxassoc 16 /sbin/wl -i wl1 bss_maxassoc 16 /sbin/wl -i wl1 nmode_protection_override -1 /sbin/wl -i wl1 protection_control 2 /sbin/wl -i wl1 protection_control 2 /sbin/wl -i wl1 rifs_advert 0 /sbin/wl -i wl1 obss_coex 0 /sbin/wl -i wl1 stbc_tx -1 /sbin/wl -i wl1 stbc_rx 1 /sbin/wl -i wl1 nreqd 0 /sbin/wl -i wl1 wme 0 2>/dev/null /sbin/wl -i wl1 afterburner_override 0 2>/dev/null /sbin/wl -i wl1 ampdu 1 /sbin/wl -i wl1 afterburner_override 0 /sbin/wl -i wl1 afterburner_override 0 /sbin/wl -i wl1 wme 1 2>/dev/null /sbin/wl -i wl1 wme_noack 0 2>/dev/null /sbin/wl -i wl1 wme_apsd 1 2>/dev/null /sbin/wl -i wl1 wme_bss_disable 0 /sbin/wl -i wl1 bands > /var/wl1bands /sbin/wl -i wl1 rate 0 /sbin/wl -i wl1 a_rate 0 /sbin/wl -i wl1 bg_rate 0 /sbin/wl leddc 0x0 /sbin/wl -i wl1 mrate -1 /sbin/wl -i wl1 a_mrate -1 /sbin/wl -i wl1 bg_mrate -1 /sbin/wl -i wl1 rtsthresh 2347 /sbin/wl -i wl1 fragthresh 2346 /sbin/wl -i wl1 dtim 2 /sbin/wl -i wl1 bi 100 /sbin/wl -i wl1 bcn_rotate 1 /sbin/wl -i wl1 frameburst 1 /sbin/wl -i wl1 ap_isolate 0 /sbin/wl -i wl1 pwr_percent 100 /sbin/wl -i wl1 wmf_bss_enable 0 /sbin/wl -i wl1.1 wmf_bss_enable 0 /sbin/wl -i wl1.2 wmf_bss_enable 0 /sbin/wl -i wl1.3 wmf_bss_enable 0 /sbin/wl -i wl1 chanim_mode 1 /sbin/wl -i wl1 rxchain_pwrsave_stas_assoc_check 1 /sbin/wl -i wl1 rxchain_pwrsave_enable 0 /sbin/wl -i wl1 rxchain_pwrsave_quiet_time 10 /sbin/wl -i wl1 rxchain_pwrsave_pps 10 /sbin/wl -i wl1 radio_pwrsave_enable 0 /sbin/wl: Not Permitted /sbin/wl -i wl1 radio_pwrsave_quiet_time 10 /sbin/wl -i wl1 radio_pwrsave_pps 1 /sbin/wl -i wl1 radio_pwrsave_level 0 /sbin/wl -i wl1 mac none /sbin/wl -i wl1 macmode 0 /sbin/wl -i wl1 up /sbin/wl -i wl1 csscantimer 0 /sbin/wl -i wl1 obss_coex 0 /sbin/wl -i wl1 rmwep -C 0 0 /sbin/wl -i wl1 rmwep -C 0 1 /sbin/wl -i wl1 rmwep -C 0 2 /sbin/wl -i wl1 rmwep -C 0 3 /sbin/wl -i wl1 rmwep -C 1 0 /sbin/wl -i wl1 rmwep -C 1 1 /sbin/wl -i wl1 rmwep -C 1 2 /sbin/wl -i wl1 rmwep -C 1 3 /sbin/wl -i wl1 rmwep -C 2 0 /sbin/wl -i wl1 rmwep -C 2 1 /sbin/wl -i wl1 rmwep -C 2 2 /sbin/wl -i wl1 rmwep -C 2 3 /sbin/wl -i wl1 rmwep -C 3 0 /sbin/wl -i wl1 rmwep -C 3 1 /sbin/wl -i wl1 rmwep -C 3 2 /sbin/wl -i wl1 rmwep -C 3 3 /sbin/wl -i wl1 wsec -C 0 4 /sbin/wl -i wl1 wsec_restrict -C 0 1 /sbin/wl -i wl1 wpa_auth -C 0 128 /sbin/wl -i wl1 eap 1 /sbin/wl -i wl1 auth -C 0 0 /sbin/wl -i wl1 wdswsec 0 /sbin/wl -i wl1 wdswsec_enable 0 /usr/sbin/brctl addif group1 wl1 device wl1 entered promiscuous mode sh: /bin/igd: not found setting oob: lan_wps_oob wps_cfg_state = 1, wps_config=ap-er wscLedSet: led_action 0, led_blink_type 0, led_event 0, led_status 0 wscLedSet: led_action 0, led_blink_type 0, led_event 0, led_status 0 issueServiceCmd SET dddddd wps_config=ap-er /sbin/wl -i wl1 bss -C 0 up /sbin/ifconfig wl1 up group1: port 6(wl1) entering learning state /sbin/ifconfig wl1.1 down /sbin/ifconfig wl1.2 down /sbin/ifconfig wl1.3 down /sbin/wl -i wl1 lazywds 0 /sbin/wl -i wl1 wds /sbin/wl -i wl1 wdstimeout 1 /sbin/wl -i wl1 phy_watchdog 1 /sbin/wl -i wl1 phycal_override_on_traffic 0 /sbin/wl -i wl1 fcache 1 /usr/sbin/sendarp -s group1 -d group1 setupAll end /sbin/wl -i wl0 rxchain_pwrsave_enable 0 /sbin/wl -i wl1 rxchain_pwrsave_enable 0 rcd: [run] deQ =/usr/sbin/rc_app/rc_wifi_isolation start sh: can't create /proc/wifi_isolation: nonexistent directory sh: can't create /proc/wifi_isolation: nonexistent directory rcd: [run] deQ =/usr/sbin/rc_app/rc_timezone start rcd: [run] deQ =/usr/sbin/rc_app/rc_sip_alg start net/netfilter/nf_conntrack_sip.c: write_proc: file: 8304c1b0, buffer: 1 , count: 2, data: 00000000 rcd: [run] deQ =/usr/sbin/rc_app/rc_dnrd start [ dnrd_main - 31 ] : do dnrd for 1 -> 1 iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. Notice: caching turned off Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off. group1: port 6(wl1) entering forwarding state rcd: [run] deQ =/usr/sbin/rc_app/rc_httpd start [sc_language.c::create_language_file():377] Create link files for <English> [sc_language.c::create_language_file():399] Checking MTD </config/language_ENU/lang> according to its id <ENU> [sc_language.c::decompress_language():164] Try to decompress MTD </config/language_ENU/lang> rmmod: cannot unload 'ipt_REJECT': Resource temporarily unavailable insmod: cannot insert '/lib/modules/ipt_REJECT.ko': File exists rcd: [run] deQ =/usr/sbin/rc_app/rc_printk start rcd: [run] deQ =/usr/sbin/rc_app/rc_ddns init rcd: [run] deQ =/usr/sbin/rc_app/rc_check_conn start rcd: [run] deQ =/usr/sbin/rc_app/rc_wan init [ wan_main - 336 ] : rc wan enter [ start_adsl - 429 ] : adsl_mode = <MMODE> rcd: [run] deQ =/usr/sbin/rc_app/rc_route start rcd: [run] deQ =/usr/sbin/rc_app/rc_ripd start rcd: [run] deQ =/usr/sbin/rc_app/rc_potcounter start killall: potcounter: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_lltd start rcd: [run] deQ =/usr/sbin/rc_app/rc_upnp start killall: miniupnpd: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_schedule start sh: can't create /proc/net/ipt_condition/schedule: nonexistent directory rcd: [run] deQ =/usr/sbin/rc_app/rc_usb_service init [ start_smb_http_en - 156 ] : entering [ start_smb_http_en - 168 ] : entering do not start_usb_httpd killall: minidlna: no process killed #### media server is disable rcd: [run] deQ =/usr/sbin/rc_app/rc_start finished rcd: [run] deQ =/usr/sbin/rc_app/rc_schedule restart sh: can't create /proc/net/ipt_condition/schedule: nonexistent directory PID USER VSZ STAT COMMAND 1 root 1012 S init 2 root 0 RW< [kthreadd] 3 root 0 SW< [migration/0] 4 root 0 SW [sirq-high/0] 5 root 0 SW [sirq-timer/0] 6 root 0 SW [sirq-net-tx/0] 7 root 0 SW [sirq-net-rx/0] 8 root 0 SW [sirq-block/0] 9 root 0 SW [sirq-tasklet/0] 10 root 0 SW [sirq-sched/0] 11 root 0 SW [sirq-hrtimer/0] 12 root 0 SW [sirq-rcu/0] 13 root 0 SW< [migration/1] 14 root 0 SW [sirq-high/1] 15 root 0 SW [sirq-timer/1] 16 root 0 SW [sirq-net-tx/1] 17 root 0 SW [sirq-net-rx/1] 18 root 0 SW [sirq-block/1] 19 root 0 SW [sirq-tasklet/1] 20 root 0 SW [sirq-sched/1] 21 root 0 SW [sirq-hrtimer/1] 22 root 0 SW [sirq-rcu/1] 23 root 0 SW< [events/0] 24 root 0 SW< [events/1] 25 root 0 SW< [khelper] 28 root 0 SW< [async/mgr] 92 root 0 SW< [kblockd/0] 93 root 0 SW< [kblockd/1] 102 root 0 SW< [khubd] 120 root 0 SW< [bpm] 136 root 0 SW [pdflush] 137 root 0 SW [pdflush] 138 root 0 SWN [kswapd0] 140 root 0 SW< [crypto/0] 141 root 0 SW< [crypto/1] 198 root 0 SW< [mtdblockd] 246 root 0 SW [board-timer] 250 root 0 SW< [linkwatch] 257 root 1024 R /bin/sh /usr/etc/rcS 305 root 0 SW [kpAliveWatchdog] 311 root 0 SW [dsl0] 320 root 0 SW [bcmsw] 321 root 0 SW [bcmsw_timer] 394 root 1492 S /usr/sbin/swmdk 396 root 1492 S /usr/sbin/swmdk 397 root 1492 S /usr/sbin/swmdk 402 root 1228 S /sbin/klogd 404 root 800 S /usr/sbin/cmd_agent_ap 406 root 0 SWN [jffs2_gcd_mtd4] 407 root 0 SWN [jffs2_gcd_mtd3] 408 root 0 SWN [jffs2_gcd_mtd12] 409 root 0 SWN [jffs2_gcd_mtd11] 410 root 0 SWN [jffs2_gcd_mtd10] 411 root 0 SWN [jffs2_gcd_mtd9] 412 root 0 SWN [jffs2_gcd_mtd2] 413 root 0 SWN [jffs2_gcd_mtd8] 419 root 884 S /usr/sbin/ft_tool 425 root 808 S /usr/sbin/rcd 430 root 992 S /sbin/lan_monitor 439 root 824 S /usr/sbin/crond 440 root 912 S /usr/sbin/multi_pb_app 90 91 92 10 40 441 root 988 S /usr/sbin/wps_ledctrl 448 root 804 S /usr/sbin/wlevt 507 root 1232 S /sbin/syslogd -f /etc/syslog.conf 887 root 872 S /var/udhcpd_1 /etc/udhcpd.conf1 1943 root 1292 S /bin/lld2d group1 1947 root 1236 S /usr/sbin/eapd 1951 root 1284 S /usr/sbin/nas 1953 root 2404 S /bin/wps_monitor 1968 root 976 S /usr/sbin/wps_det do_addER_reset 2334 root 1316 S /var/dnrd_1 -a 192.168.0.1 -m hosts -c off -g routerl 2427 root 1780 S /usr/sbin/mini_httpd -d /www -r NETGEAR DGND3700v2 -c 2480 root 1080 S /bin/wan_monitor 2513 root 808 S /usr/sbin/potcounter 2518 root 944 S /usr/bin/lld2 group1 2546 root 1220 S /usr/sbin/miniupnpd -i ppp1 -a 192.168.0.1 -p 56688 - 2820 root 0 SW [ telnetDBGD ] 2821 root 0 SW [ acktelnetDBGD ] 2822 root 0 SW [checkSBusTimeou] 2824 root 0 DW [NU INITSOCK] 2825 root 1016 R /bin/ps Please press Enter to activate this console.

# cat /proc/mounts rootfs / rootfs rw 0 0 mtd:rootfs / jffs2 ro,relatime 0 0 proc /proc proc rw,relatime 0 0 sysfs /sys sysfs rw,relatime 0 0 ramfs /home ramfs rw,relatime 0 0 ramfs /tmp ramfs rw,relatime 0 0 ramfs /mnt ramfs rw,relatime 0 0 ramfs /dev ramfs rw,relatime 0 0 devpts /dev/pts devpts rw,relatime,mode=600,ptmxmode=000 0 0 mtd:factory /config/factory jffs2 rw,relatime 0 0 mtd:scnvram /config/nvram jffs2 rw,relatime 0 0 mtd:language_ENU /config/language_ENU jffs2 rw,relatime 0 0 mtd:language_CHS /config/language_CHS jffs2 rw,relatime 0 0 mtd:language_RUS /config/language_RUS jffs2 rw,relatime 0 0 mtd:language_PTB /config/language_PTB jffs2 rw,relatime 0 0 mtd:language_DEU /config/language_DEU jffs2 rw,relatime 0 0 mtd:xxx /config/xxx jffs2 rw,relatime 0 0 # # cat /proc/cpuinfo system type : 96362ADVN2xh processor : 0 cpu model : Broadcom4350 V7.0 BogoMIPS : 399.36 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no ASEs implemented : shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available

unaligned exceptions : 253 processor : 1 cpu model : Broadcom4350 V7.0 BogoMIPS : 402.43 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no ASEs implemented : shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available

unaligned exceptions : 253 # #


OpenWrt Bootlog

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS ZQDN PHYE DINT LASY USYN MSYN LMBE PASS ---- ZBSS CODE DATA L12F MAIN NAN0 BTam 0001 NAN9 NAN3 RFS0 NAN5 CFE version 1.0.38-112.14 for BCM96362 (32bit,SP,BE) Build Date: 2011年 12月 21日 星期三 18:16:05 CST (sunny@localhost) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name <not identified>, id 0x2075 block 16KB size 32768KB External switch id = 53125 SC Debug: Setting RGMII TX_CLK DELAY at SWITCH IMP PORT! SC Debug: Setting RGMII RX_CLK DELAY at SWITCH IMP PORT! Chip ID: BCM6362B0, MIPS: 400MHz, DDR: 333MHz, Bus: 166MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.4:ffffff00 Host IP address : 192.168.1.8 Gateway IP address : 192.168.1.1 Run from flash/host (f/h) : f Default host run file name : dgnd3700v2.elf Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-5) : 96362ADVN2xh Number of MAC Addresses (1-32) : 11 Base MAC Address : 4c:60:de:xx:xx:xx PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Enter NMRP_main Scanning Flash Section 0... Scanning Flash Section 1... Scanning Flash Section 2... Scanning Flash Section 3... Scanning Flash Section 4... Scanning Flash Section 5... Scanning Flash Section 6... Scanning Flash Section 7... Scanning Flash Section 8... Scanning Flash Section 9... Scanning Flash Section 10... Scanning Flash Section 11... Scanning Flash Section 12... NMRP:LISTENING ### No NMRP Server found ### Scanning Flash Section 0... Scanning Flash Section 1... Scanning Flash Section 2... Scanning Flash Section 3... Scanning Flash Section 4... Scanning Flash Section 5... Scanning Flash Section 6... Scanning Flash Section 7... Scanning Flash Section 8... Scanning Flash Section 9... Scanning Flash Section 10... Scanning Flash Section 11... Scanning Flash Section 12... *************************************************** Sercomm Boot Version 1...0.6 *************************************************** 0 Block in Flag Section Find Sercomm Sign! Entering Firmware : Everything is OK. Booting from Primary image (0xb8080000) ... Decompression OK! Entry at 0x80a00000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 1 buffers found. Closing DMA Channels. Starting program at 0x80a00000 [ 0.000000] Linux version 5.4.41 (noltari@skynet) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r12787-af5ccfbac7)) #0 SMP Tue May 19 06:55:06 2020 [ 0.000000] Detected Broadcom 0x6362 CPU revision b0 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.38-112.14 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0002a070 (Broadcom BMIPS4350) [ 0.000000] board: board name: 96362ADVN2xh [ 0.000000] MIPS: machine is Netgear DGND3700v2 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s26048 r8192 d23104 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: rootfstype=squashfs,ubifs noinitrd console=ttyS0,115200 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 56104K/65536K available (5690K kernel code, 219K rwdata, 1216K rodata, 1316K init, 206K bss, 9432K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x338/0x560 with crng_init=0 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000015] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008146] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.046462] pid_max: default: 32768 minimum: 301 [ 0.051578] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059139] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.072854] rcu: Hierarchical SRCU implementation. [ 0.079210] smp: Bringing up secondary CPUs ... [ 0.085719] SMP: Booting CPU1... [ 9.398958] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 9.398977] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 9.399237] CPU1 revision is: 0002a070 (Broadcom BMIPS4350) [ 0.121265] Synchronize counters for CPU 1: [ 0.121286] SMP: CPU1 is running [ 0.121309] done. [ 0.151849] smp: Brought up 1 node, 2 CPUs [ 0.165278] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.175345] futex hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.182587] pinctrl core: initialized pinctrl subsystem [ 0.189133] NET: Registered protocol family 16 [ 0.438678] registering PCI controller with io_map_base unset [ 0.491918] random: fast init done [ 0.512301] PCI host bridge to bus 0000:00 [ 0.516607] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff] [ 0.523780] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.530775] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.537724] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.545939] pci 0000:00:00.0: [14e4:6362] type 01 class 0x060400 [ 0.552224] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.559885] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.568463] pci 0000:01:00.0: [14e4:4359] type 00 class 0x028000 [ 0.574722] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 0.581746] pci 0000:01:00.0: enabling Extended Tags [ 0.586973] pci 0000:01:00.0: supports D1 D2 [ 0.591326] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.599608] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.606435] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.613245] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff] [ 0.620228] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit] [ 0.627755] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.632838] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff] [ 0.643563] clocksource: Switched to clocksource MIPS [ 0.653155] NET: Registered protocol family 2 [ 0.660217] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.668983] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.676921] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.684262] TCP: Hash tables configured (established 1024 bind 1024) [ 0.691325] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.698181] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.705990] NET: Registered protocol family 1 [ 0.710619] PCI: CLS 0 bytes, default 16 [ 0.719090] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.741093] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.747122] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.790473] bcm6362-pinctrl 10000080.pin-controller: registered at mmio (ptrval) [ 0.799053] pcieport 0000:00:00.0: enabling device (0000 -> 0002) [ 0.806312] 10000100.serial: ttyS0 at MMIO 0x10000100 (irq = 11, base_baud = 1562500) is a bcm63xx_uart [ 0.816067] printk: console [ttyS0] enabled [ 0.816067] printk: console [ttyS0] enabled [ 0.824635] printk: bootconsole [early0] disabled [ 0.824635] printk: bootconsole [early0] disabled [ 0.848551] nand: device found, Manufacturer ID: 0x20, Chip ID: 0x75 [ 0.855130] nand: ST Micro NAND 32MiB 3,3V 8-bit [ 0.859873] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 0.867419] bcm6368_nand 10000200.nand: detected 32MiB total, 16KiB blocks, 512B pages, 16B OOB, 8-bit, Hamming ECC [ 0.878565] Bad block table found at page 65504, version 0x01 [ 0.884732] Bad block table found at page 65472, version 0x01 [ 0.892151] 7 fixed-partitions partitions found on MTD device brcmnand.0 [ 0.899094] Creating 7 MTD partitions on "brcmnand.0": [ 0.904379] 0x000000000000-0x000000004000 : "cferom" [ 0.911444] 0x000000004000-0x000001c80000 : "wfi" [ 1.068334] 4 bcm-wfi-fw partitions found on MTD device wfi [ 1.074054] Creating 4 MTD partitions on "wfi": [ 1.078717] 0x000000000000-0x00000009c000 : "cferam" [ 1.085885] 0x00000009c000-0x000001c7c000 : "firmware" [ 1.094789] 0x00000009c000-0x00000059c000 : "kernel" [ 1.102107] 0x00000059c000-0x000001c7c000 : "ubi" [ 1.110243] 0x000001c80000-0x000001cc0000 : "flag" [ 1.117160] 0x000001cc0000-0x000001d00000 : "pcbasn" [ 1.124343] 0x000001d00000-0x000001d80000 : "xxx" [ 1.131125] 0x000001d80000-0x000001dc0000 : "language_dev" [ 1.138853] 0x000001dc0000-0x000001ec0000 : "scnvram" [ 1.166004] bcm63xx-spi 10000800.spi: at [mem 0x10000800-0x10000f0b flags 0x200] (irq 10, FIFOs size 542) [ 1.180524] libphy: Fixed MDIO Bus: probed [ 1.185269] bcm63xx_enetsw bcm63xx_enetsw.0: IRQ index 1 not found [ 1.235212] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 1.245583] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.252794] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.259933] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.267099] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.274280] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.281787] bcma-pci-bridge 0000:01:00.0: enabling device (0000 -> 0002) [ 1.288751] bcma-pci-bridge 0000:01:00.0: bus0: Found chip with id 43228, rev 0x00 and package 0x08 [ 1.298099] bcma-pci-bridge 0000:01:00.0: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x25, class 0x0) [ 1.309052] bcma-pci-bridge 0000:01:00.0: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1E, class 0x0) [ 1.320106] bcma-pci-bridge 0000:01:00.0: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x12, class 0x0) [ 1.330519] bcma-pci-bridge 0000:01:00.0: bus0: Core 3 found: SDIO Device (manuf 0x4BF, id 0x829, rev 0x07, class 0x0) [ 1.361937] bcma-pci-bridge 0000:01:00.0: bus0: Bus registered [ 1.370296] NET: Registered protocol family 10 [ 1.382868] Segment Routing with IPv6 [ 1.386908] NET: Registered protocol family 17 [ 1.391626] 8021q: 802.1Q VLAN Support v1.8 [ 1.422329] UBI: auto-attach mtd5 [ 1.425890] ubi0: attaching mtd5 [ 1.918738] ubi0: scanning is finished [ 1.942867] ubi0: attached mtd5 (name "ubi", size 22 MiB) [ 1.948459] ubi0: PEB size: 16384 bytes (16 KiB), LEB size: 15360 bytes [ 1.955236] ubi0: min./max. I/O unit sizes: 512/512, sub-page size 512 [ 1.961948] ubi0: VID header offset: 512 (aligned 512), data offset: 1024 [ 1.968937] ubi0: good PEBs: 1464, bad PEBs: 0, corrupted PEBs: 0 [ 1.975209] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 89 [ 1.982558] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1588945797 [ 1.991967] ubi0: available PEBs: 0, total reserved PEBs: 1464, PEBs reserved for bad PEB handling: 40 [ 2.001603] ubi0: background thread "ubi_bgt0d" started, PID 442 [ 2.005421] block ubiblock0_0: created from ubi0:0(rootfs) [ 2.013489] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 2.034476] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 2.058897] Freeing unused kernel memory: 1316K [ 2.063555] This architecture does not have kernel memory protection. [ 2.070157] Run /sbin/init as init process [ 2.968043] init: Console is alive [ 2.971933] init: - watchdog - [ 4.551185] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.712846] usbcore: registered new interface driver usbfs [ 4.718691] usbcore: registered new interface driver hub [ 4.724352] usbcore: registered new device driver usb [ 4.743625] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.752703] ehci-fsl: Freescale EHCI Host controller driver [ 4.761243] ehci-platform: EHCI generic platform driver [ 4.871530] ehci-platform ehci-platform: EHCI Host Controller [ 4.877506] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 4.886028] ehci-platform ehci-platform: irq 18, io mem 0xb0002500 [ 4.907511] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored [ 4.917370] hub 1-0:1.0: USB hub found [ 4.921378] hub 1-0:1.0: 2 ports detected [ 4.937502] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.945951] ohci-platform: OHCI generic platform driver [ 4.951736] ohci-platform ohci-platform: Generic Platform OHCI controller [ 4.958760] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 4.967082] ohci-platform ohci-platform: irq 17, io mem 0xb0002600 [ 5.037045] hub 2-0:1.0: USB hub found [ 5.041052] hub 2-0:1.0: 2 ports detected [ 5.047180] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.060268] init: - preinit - [ 6.523143] random: jshn: uninitialized urandom read (4 bytes read) [ 6.601227] random: jshn: uninitialized urandom read (4 bytes read) [ 6.703164] random: jshn: uninitialized urandom read (4 bytes read) [ 6.940228] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.323581] random: crng init done [ 8.327027] random: 3 urandom warning(s) missed due to ratelimiting [ 11.339382] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 11.345774] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 559 [ 11.363814] UBIFS (ubi0:1): recovery needed [ 11.450218] UBIFS (ubi0:1): recovery completed [ 11.455094] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 11.463139] UBIFS (ubi0:1): LEB size: 15360 bytes (15 KiB), min./max. I/O unit sizes: 512 bytes/512 bytes [ 11.472990] UBIFS (ubi0:1): FS size: 18754560 bytes (17 MiB, 1221 LEBs), journal size 936960 bytes (0 MiB, 61 LEBs) [ 11.483725] UBIFS (ubi0:1): reserved for root: 885824 bytes (865 KiB) [ 11.490364] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 2BA5E257-5BDA-445B-9485-709B8AFA4D20, small LPT model [ 11.503942] mount_root: switching to ubifs overlay [ 11.552366] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 11.567936] urandom-seed: Seeding with /etc/urandom.seed [ 11.774344] procd: - early - [ 11.777651] procd: - watchdog - [ 12.467668] procd: - watchdog - [ 12.471289] procd: - ubus - [ 12.692575] procd: - init - Please press Enter to activate this console. [ 13.858119] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.022428] Loading modules backported from Linux version v5.4.27-0-g585e0cc08069 [ 14.030262] Backport generated by backports.git v5.4.27-1-0-gf6e8852f [ 14.093729] xt_time: kernel timezone is -0000 [ 14.202551] urngd: v1.0.2 started. [ 14.393616] PPP generic driver version 2.4.2 [ 14.401839] NET: Registered protocol family 24 [ 14.480781] b43-phy0: Broadcom 43228 WLAN found (core revision 30) [ 14.487737] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 16 [ 14.494145] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1 [ 14.502953] Broadcom 43xx driver loaded [ Features: PNL ] [ 14.603886] kmodloader: done loading kernel modules from /etc/modules.d/* [ 28.360192] br-lan: port 1(eth0) entered blocking state [ 28.365642] br-lan: port 1(eth0) entered disabled state [ 28.371911] device eth0 entered promiscuous mode [ 28.402095] br-lan: port 1(eth0) entered blocking state [ 28.407554] br-lan: port 1(eth0) entered forwarding state [ 29.356394] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/netgear/dgnd3700v2.txt · Last modified: 2020/06/25 16:44 by danitool