[OpenWrt Wiki] NETGEAR N450/CG3000Dv2

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== NETGEAR N450/CG3000Dv2 ======
The Netgear N450/CG3000Dv2 is a Docsis 3.0 cable modem combined with a four port gigabit switch and a Wi-Fi modem. It is built with the same PCB as the [[:inbox:toh:openwrt:cg3000-2staus|CG3000-2STAUS]] but is lacking voice over IP capabilities and an RJ45 WAN port. Adding the WAN port may be as easy as soldering in a jack, but the VoIP functionality would require adding multiple parts. 

**Currently not suppported.**
{{page>meta:infobox:construction&noheader&nofooter&noeditbtn}}

===== Hardware =====
==== Info ====
^ [[wp>Instruction set|Architecture]] | [[wp>MIPS architecture|MIPS]] |
^ Vendor | [[wp>Broadcom]] |
^ [[docs:techref:bootloader]] | ? |
^ [[docs:techref:hardware:soc|System-On-Chip]] | Broadcom BCM3383 |
^ [[docs:techref:hardware:cpu|CPU]]/Speed | BMIPS?? / ? MHz |
^ NAND Flash | Spansion {{:media:datasheets:flash:002-00499_S34ML01G2_S34ML02G2_S34ML04G2_1_Gb_2_Gb_4_Gb_3_V_4-bit_ECC_SLC_NAND_Flash_Memory_for_Embedded.pdf|S34ML01G200TF100}} SLC NAND Flash Memory |
^ NAND Flash size | 128 MiB |
^ SPI Flash | Macronix {{:media:datasheets:flash:MX25L8006E.pdf|MX25L8006E}} [[#SPI Flash|SPI Flash]] |
^ SPI Flash size | 1 MiB |
^ RAM-Chip | Samsung {{:media:datasheets:ram:k4b1g1646g.pdf|K4B1G1646G}} DDR3 SDRAM |
^ RAM size | 128 MiB |
^ Wireless | Broadcom 802.11b/g/n |
^ Ethernet | Broadcom 10BASE-T, 100/1000BASE-Tx |
^ USB | Two USB 2.0|
^ [[docs:techref:hardware:port.serial|Serial]] | [[#Serial|Two 3.3v TTL serial ports]] |
^ [[docs:techref:hardware:port.jtag|JTAG]] | Probably  |

==== Photos ====
=== Router front===
{{media:netgear:cg3000dv2:cg3000dv2_front.png|}}
=== Router rear===
{{media:netgear:cg3000dv2:cg3000dv2_rear.png|}}
=== Board top ===
{{media:netgear:cg3000dv2:cg3000dv2_pcb_top.png?400|}}
=== Board bottom ===
{{media:netgear:cg3000dv2:cg3000dv2_pcb_bottom.png?400|}}

==== Serial ====
There are two 3.3v TTL serial ports, both connecting at 115200, 8, N, 1, software flow control.

UART0 (J20) gives what appears to be a non-interactive console for the eCos part of the modem/router.

{{media:netgear:cg3000dv2:cg3000dv2_serial_top.png?400|}}

<sup>1</sup>UART1 (J21) gives an interactive console for the Linux part of the modem/router.
Login with username: root, password: broadcom

Notes:\\ 
1. UART1 may be disabled on some OEM firmware releases. See below. 
==== SPI Flash ====
{{media:netgear:cg3000dv2:cg3000dv2_spi_flash.png?400|}}
===== Bootlogs =====
Bootlogs are dependent on the currently deployed [[https://kb.netgear.com/000036375/What-s-the-latest-firmware-version-of-my-NETGEAR-cable-modem-or-modem-router|OEM firmware release]] which can vary depending on your ISP.
==== eCos Bootlog V3.01.17 ====
Firmware version 3.01.17 appears to disable the serial port on UART1; therefore there is no accompanying Linux Bootlog seen on that port. 
<WRAP bootlog>
<nowiki>
BCM338332 TP0 346890                                                                                            
Reset Switch - Low GPIO-32 50ms                                                                                 
MemSize:            128 M                                                                                       
Chip ID:     BCM3383G-B0                                                                                        
                                                                                                                
BootLoader Version: 2.4.0beta1R8 Pre-release Gnu spiboot reduced DDR drive linux                                
Build Date: Apr 15 2013                                                                                         
Build Time: 15:17:07                                                                                            
SPI flash ID 0xc22014, size 1MB, block size 64KB, write buffer 256, flags 0x0                                   
NAND flash: Device size 128 MB, Block size 128 KB, Page size 2048 B                                             
parameter offset is 40936

Signature/PID: a0df

NandFlashRead: Reading offset 0x1f40000, length 0x5c

Image 1 Program Header:
   Signature: a0df
     Control: 0005
   Major Rev: 0003
   Minor Rev: 0000
  Build Time: 2017/7/3 03:05:14 Z
 File Length: 4520243 bytes
Load Address: 80004000
    Filename: 0001N450-100NAS_V3.01.16u.bin
         HCS: 4922
         CRC: 3e86e9ee

Found image 1 at offset 2040000
NandFlashRead: Reading offset 0x2840000, length 0x5c

Image 2 Program Header:
   Signature: a0df
     Control: 0005
   Major Rev: 0003
   Minor Rev: 0000
  Build Time: 2017/9/22 01:17:45 Z
 File Length: 4521990 bytes
Load Address: 80004000
    Filename: 0001N450-100NAS_V3.01.17u.bin
         HCS: 30cf
         CRC: e23cd806

Found image 2 at offset 2940000
NandFlashRead: Reading offset 0x3140000, length 0x5c

Image 3 Program Header:
   Signature: a0df
     Control: 0005
   Major Rev: 0002
   Minor Rev: 0017
  Build Time: 2017/9/22 01:01:37 Z
 File Length: 1507236 bytes
Load Address: 84010000
    Filename: CG3000D_2TCNAS_K2630V3.01.17nu.bin
         HCS: 10e4
         CRC: 3447f162

Found image 3 at offset 3240000
NandFlashRead: Reading offset 0x3140000, length 0x200
NandFlashRead: Reading offset 0x3140200, length 0x16fe00
Performing CRC on Image 3...
CRC time = 219484070
Detected LZMA compressed image... decompressing... 
Target Address: 0x84010000
decompressSpace is 0x8000000
Elapsed time 729988980

Decompressed length: 6284126
Done Copying Root File System...

NandFlashRead: Reading offset 0x2840000, length 0x200
NandFlashRead: Reading offset 0x2840200, length 0x44fe62
NandFlashRead: 1 errors reading buffer at offset 28ee200
Performing CRC on Image 2...
CRC time = 321043847
Detected LZMA compressed image... decompressing... 
Target Address: 0x80004000
decompressSpace is 0x8000000
Elapsed time 3050741930

Decompressed length: 23281496
Copying partition table to 0x83fffc04 240
Copying partition table to 0x80000904 240

Executing Image 2...


 eCos - hal_diag_init
Init device '/dev/BrcmTelnetIoDriver'
Init device '/dev/ttydiag'
Init tty channel: 816379a8
Init device '/dev/tty0'
Init tty channel: 816379c8
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: b4e00500.2
Set output buffer - buf: 0x81859b50 len: 4096
Set input buffer - buf: 0x8185ab50 len: 4096
BCM 33XX SERIAL config
Init device '/dev/ser1'
BCM 33XX SERIAL init - dev: b4e00520.3
Set output buffer - buf: 0x8185bb50 len: 4096
Set input buffer - buf: 0x8185cb50 len: 4096
BCM 33XX SERIAL config

Init device '/dev/ser2'
InitBoard: MIPS frequency 637200000
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Configuring/Loading Flash driver...
[00:00:00 01/01/1970] [tStartup] BcmSpiFlashDevice::DetectFlash:  (SPI Flash Device Factory) WARNING - Detected SPI flash with JEDEC ID =0xc22014
Waited 296 iterations after device ID read
NAND flash: Device size 128 MB, Block size 128 KB, Page size 2048 B
[00:00:00 01/01/1970] [tStartup] BcmNandFlashDevice::DetectNandFlash:  (NAND Flash Device Factory) WARNING - Detected NAND flash with JEDEC ID =0x1f1801d
Found bootloader flash map at 0x80000904.
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Loading BootloaderStore driver...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Loading ProgramStore driver...
ProgramStoreDeviceDriver::ProgramStoreDriverInit:  INFO - Initializing...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Loading NonVol driver...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Storage drivers initialized successfully.
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions:  (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
Bootloader indicates we are running image 2
By default, we will dload to image number 1!

[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions:  (BFC Target) Device abstraction singletons created successfully.

Init TWC US Table 0
Init TWC US Table 1
Init TWC US Table 2
Init TWC US Table 3
BcmPcpClientServiceAppIf::GetSingletonInstance:  WARNING - the singleton is NULL, and someone is accessing it!

Reading Permanent settings from non-vol...
[00:00:00 01/01/1970] [PowerOnTimeKeeperThread Thread] PowerOnTimeKeeperThread::ThreadMain:  (PowerOnTimeKeeperThread Thread) PowerOnTimeKeeper Thread is running...
Checksum for permanent settings:  0x8e12ed58
[00:00:00 01/01/1970] [tStartup] BcmWiFi80211SromNonVolSettings::ReadFromImpl:  (WiFi 802.11 Srom NonVol Settings) WARNING - Read older version of the settings (0.1); they have been upgraded to version 0.2, preserving original settings.
Setting downstream calibration signature to ''
[00:00:00 01/01/1970] [tStartup] BcmDocsisCmDownstreamCalibrationNonVolSettings::ReadFromImpl:  (DOCSIS CM Downstream Calibration NonVol Settings) WARNING - Read older version of the settings (2.0); they have been upgraded to version 2.1, preserving original settings.
[00:00:00 01/01/1970] [tStartup] BcmCmVendorNonVolSettings::ReadFromImpl:  (CM Netgear NonVol Settings) WARNING - Read older version of the settings (0.9); they have been upgraded to version 0.12, preserving original settings.
[00:00:00 01/01/1970] [tStartup] BcmSpectrumAnalyzerNonVolSettings::IsDefault:  (Spectrum Analyzer NonVol Settings) Permanent settings are default!

*
*
* One or more of the settings groups was missing, possibly as a result of a code upgrade.
*
*

*
*
* One or more of the settings groups was upgraded.
*
*
Settings were read and verified.


Reading Dynamic settings from non-vol...
Checksum for dynamic settings:  0xa87b0979
BcmPcpClientServiceAppIf::GetSingletonInstance:  WARNING - the singleton is NULL, and someone is accessing it!
Settings were read and verified.


Reading Vendor settings from non-vol...
Checksum for Vendor settings:  0xd9c2a080
Settings were read and verified.

[00:00:00 01/01/1970] [tStartup] BcmEpsCmDocsisSystem::Initialize:  (BFC System) ERROR - Disable console port now!
[00:00:00 01/01/1970] [Reset/Standby Switch Thread] BcmResetStandbySwitchThread::ProcessResetSwitchEvent:  (Reset/Standby Switch Thread) Reset switch released; resetting...
[00:00:00 01/01/1970] [Reset/Standby Switch Thread] BcmResetStandbySwitchThread::ProcessResetSwitchEvent:  (Reset/Standby Switch Thread) Cant Reset pfCmDocsisCtlThread==NULL...
Creating a new host MSG PROC DQM manager. Instance: 83ed148c, DQM_REGS = b8601800, CTRL_REGS = b8601000
Initializing main MSP DQM interrupts.
 b8601000: 01800008
 b8601004: 00000000
 b8601008: 00000008
 b860100c: 00000000
 b8601010: 000c0000
 b8601014: 00000000
 b8601018: 00000000
 b860101c: 00000000
Creating a new host FAP DQM manager. Instance: 83ed4f88
Initializing main FAP DQM interrupts.
 b8401000: 00000008
 b8401004: 00000000
 b8401008: 00000008
 b840100c: 00000000
 b8401010: 00000000
 b8401014: 00000000
 b8401018: 00000000
 b840101c: 00000000
Creating a new host PMC DQM manager. Instance: 83ed2368, DQM_REGS = b8801800, CTRL_REGS = b8801000
Initializing main PMC DQM interrupts.
 b8801000: 00000000
 b8801004: 00000000
 b8801008: 00000008
 b880100c: 00000000
 b8801010: 00000000
 b8801014: 00000000
 b8801018: 00000000
 b880101c: 00000000
Creating a new host PMC DQM manager. Instance: 83ed22e8, DQM_REGS = b8801800, CTRL_REGS = b8801000
Initializing main DTP DQM interrupts.
 b8201000: 0000004c
 b8201004: 00000000
 b8201008: 00000008
 b820100c: 00000000
 b8201010: 00000000
 b8201014: 00040000
 b8201018: 00000000
 b820101c: 00000000
Creating a new host FAP DQM manager. Instance: 82f00894
Creating a new host FAP DQM manager. Instance: 82f007ac
Creating a new host UTP DQM manager. Instance: 82efc6b0
Initializing main UTP DQM interrupts.
 b8001000: 00000049
 b8001004: 00000000
 b8001008: 00000008
 b800100c: 00000000
 b8001010: 00000001
 b8001014: 00000000
 b8001018: 00000000
 b800101c: 00000000
Initalizing Gfap Hal..
LNA Detected = BCM3413
Positive Saturation
Positive Saturation
ADC Clocks aligned
Initializing all 8 downstreams - this takes a while.  Patience, Grasshopper...
1 2 3 4 5 6 7 8 
Creating a new host UTP DQM manager. Instance: 82ebf9e4
Creating a new host UTP DQM manager. Instance: 82eaf5f4
Creating a new host UTP DQM manager. Instance: 82eaf52c
Powering UP switch. PIN = 14
Creating a new host MSG PROC DQM manager. Instance: 82eaec60, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82eaeb98, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82eae9f4, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82eae7f4, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host FAP DQM manager. Instance: 82eae5f4
Creating a new host FAP DQM manager. Instance: 82eae3ec
Creating a new host MPEG PROC DQM manager. Instance: 82eae1e4, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Initializing main MEP DQM interrupts.
 b8a01000: 00000008
 b8a01004: 00000000
 b8a01008: 00000008
 b8a0100c: 00000000
 b8a01010: 00000000
 b8a01014: 00000000
 b8a01018: 00000000
 b8a0101c: 00000000
Creating a new host MPEG PROC DQM manager. Instance: 82eadfec, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Creating a new host MSG PROC DQM manager. Instance: 82e95034, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82e94e2c, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82e94d74, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82e92c90, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82e92c28, DQM_REGS = b8601800, CTRL_REGS = b8601000
Register Int Handler: busNo = 1, device = 0
Creating a new host PMC DQM manager. Instance: 82d97afc, DQM_REGS = b8801800, CTRL_REGS = b8801000
Creating a new host MPEG PROC DQM manager. Instance: 82a8bc88, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Creating a new host MPEG PROC DQM manager. Instance: 829211cc, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Creating a new host MPEG PROC DQM manager. Instance: 8292111c, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Creating a new host PMC DQM manager. Instance: 82f62be8, DQM_REGS = b8801800, CTRL_REGS = b8801000</nowiki>
</WRAP>\\
==== eCos Bootlog V3.01.06 ====
<WRAP bootlog>
<nowiki>
BCM338332 TP0 346890
Reset Switch - Low GPIO-32 50ms
MemSize:            128 M
Chip ID:     BCM3383G-B0

BootLoader Version: 2.4.0beta1R8 Pre-release Gnu spiboot reduced DDR drive linux
Build Date: Apr 15 2013
Build Time: 15:17:07
SPI flash ID 0xc22014, size 1MB, block size 64KB, write buffer 256, flags 0x0
NAND flash: Device size 128 MB, Block size 128 KB, Page size 2048 B
parameter offset is 40936

Signature/PID: a0df

NandFlashRead: Reading offset 0x1f40000, length 0x5c

Image 1 Program Header:
   Signature: a0df
     Control: 0005
   Major Rev: 0003
   Minor Rev: 0000
  Build Time: 2015/12/24 02:45:08 Z
 File Length: 4460665 bytes
Load Address: 80004000
    Filename: 0001N450-100NAS_V3.01.06u.bin
         HCS: 7768
         CRC: 8557ad58

Found image 1 at offset 2040000
NandFlashRead: Reading offset 0x2840000, length 0x5c
NandFlashRead: Reading offset 0x3140000, length 0x5c

Image 3 Program Header:
   Signature: a0df
     Control: 0005
   Major Rev: 0002
   Minor Rev: 0017
  Build Time: 2015/12/24 02:38:17 Z
 File Length: 1507236 bytes
Load Address: 84010000
    Filename: CG3000D_2TCNAS_K2630V3.01.06nu.bin
         HCS: 397c
         CRC: 979a4649

Found image 3 at offset 3240000
NandFlashRead: Reading offset 0x3140000, length 0x200
NandFlashRead: Reading offset 0x3140200, length 0x16fe00
Performing CRC on Image 3...
CRC time = 210254496
Detected LZMA compressed image... decompressing... 
Target Address: 0x84010000
decompressSpace is 0x8000000
Elapsed time 733141540

Decompressed length: 6301023
Done Copying Root File System...

NandFlashRead: Reading offset 0x1f40000, length 0x200
NandFlashRead: Reading offset 0x1f40200, length 0x440ed5
Performing CRC on Image 1...
CRC time = 310373412
Detected LZMA compressed image... decompressing... 
Target Address: 0x80004000
decompressSpace is 0x8000000
Elapsed time 3017165660

Decompressed length: 22777536
Copying partition table to 0x83fffc04 240
Copying partition table to 0x80000904 240

Executing Image 1...


 eCos - hal_diag_init
Init device '/dev/BrcmTelnetIoDriver'
Init device '/dev/ttydiag'
Init tty channel: 815bc910
Init device '/dev/tty0'
Init tty channel: 815bc930
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: b4e00500.2
Set output buffer - buf: 0x817cd790 len: 4096
Set input buffer - buf: 0x817ce790 len: 4096
BCM 33XX SERIAL config
Init device '/dev/ser1'
BCM 33XX SERIAL init - dev: b4e00520.3
Set output buffer - buf: 0x817cf790 len: 4096
Set input buffer - buf: 0x817d0790 len: 4096
BCM 33XX SERIAL config

Init device '/dev/ser2'
InitBoard: MIPS frequency 637200000
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Configuring/Loading Flash driver...
[00:00:00 01/01/1970] [tStartup] BcmSpiFlashDevice::DetectFlash:  (SPI Flash Device Factory) WARNING - Detected SPI flash with JEDEC ID =0xc22014
Waited 296 iterations after device ID read
NAND flash: Device size 128 MB, Block size 128 KB, Page size 2048 B
[00:00:00 01/01/1970] [tStartup] BcmNandFlashDevice::DetectNandFlash:  (NAND Flash Device Factory) WARNING - Detected NAND flash with JEDEC ID =0x1f1801d
Found bootloader flash map at 0x80000904.
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::SpiFlashPlaceRegions:  (Flash Driver C API) WARNING - Partition falls out of range of device 0. Placing in device 1...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Loading BootloaderStore driver...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Loading ProgramStore driver...
ProgramStoreDeviceDriver::ProgramStoreDriverInit:  INFO - Initializing...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Loading NonVol driver...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers:  (BFC Target) Storage drivers initialized successfully.
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions:  (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
Bootloader indicates we are running image 1
By default, we will dload to image number 2!

[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions:  (BFC Target) Device abstraction singletons created successfully.

Init TWC US Table 0
Init TWC US Table 1
Init TWC US Table 2
Init TWC US Table 3
BcmPcpClientServiceAppIf::GetSingletonInstance:  WARNING - the singleton is NULL, and someone is accessing it!

Reading Permanent settings from non-vol...
[00:00:00 01/01/1970] [PowerOnTimeKeeperThread Thread] PowerOnTimeKeeperThread::ThreadMain:  (PowerOnTimeKeeperThread Thread) PowerOnTimeKeeper Thread is running...
Checksum for permanent settings:  0xec8fc5d2
Setting downstream calibration signature to ''
Settings were read and verified.


Reading Dynamic settings from non-vol...
Checksum for dynamic settings:  0xd026364e
Settings were read and verified.


Reading Vendor settings from non-vol...
Checksum for Vendor settings:  0x86725f22
Settings were read and verified.

[00:00:00 01/01/1970] [tStartup] BcmEpsCmDocsisSystem::Initialize:  (BFC System) ERROR - Disable console port now!
[00:00:00 01/01/1970] [Reset/Standby Switch Thread] BcmResetStandbySwitchThread::ProcessResetSwitchEvent:  (Reset/Standby Switch Thread) Reset switch released; resetting...
[00:00:00 01/01/1970] [Reset/Standby Switch Thread] BcmResetStandbySwitchThread::ProcessResetSwitchEvent:  (Reset/Standby Switch Thread) Cant Reset pfCmDocsisCtlThread==NULL...
Creating a new host MSG PROC DQM manager. Instance: 83f18724, DQM_REGS = b8601800, CTRL_REGS = b8601000
Initializing main MSP DQM interrupts.
 b8601000: 01800008
 b8601004: 00000000
 b8601008: 00000008
 b860100c: 00000000
 b8601010: 000c0000
 b8601014: 00000000
 b8601018: 00000000
 b860101c: 00000000
Creating a new host FAP DQM manager. Instance: 83f18634
Initializing main FAP DQM interrupts.
 b8401000: 00000008
 b8401004: 00000000
 b8401008: 00000008
 b840100c: 00000000
 b8401010: 00000000
 b8401014: 00000000
 b8401018: 00000000
 b840101c: 00000000
Creating a new host PMC DQM manager. Instance: 83f1a004, DQM_REGS = b8801800, CTRL_REGS = b8801000
Initializing main PMC DQM interrupts.
 b8801000: 00000000
 b8801004: 00000000
 b8801008: 00000008
 b880100c: 00000000
 b8801010: 00000000
 b8801014: 00000000
 b8801018: 00000000
 b880101c: 00000000
Creating a new host PMC DQM manager. Instance: 83f19f84, DQM_REGS = b8801800, CTRL_REGS = b8801000
Initializing main DTP DQM interrupts.
 b8201000: 0000004c
 b8201004: 00000000
 b8201008: 00000008
 b820100c: 00000000
 b8201010: 00000000
 b8201014: 00040000
 b8201018: 00000000
 b820101c: 00000000
Creating a new host FAP DQM manager. Instance: 82f13c7c
Creating a new host FAP DQM manager. Instance: 82f13b94
Creating a new host UTP DQM manager. Instance: 82f0fa98
Initializing main UTP DQM interrupts.
 b8001000: 00000049
 b8001004: 00000000
 b8001008: 00000008
 b800100c: 00000000
 b8001010: 00000001
 b8001014: 00000000
 b8001018: 00000000
 b800101c: 00000000
Initalizing Gfap Hal..
LNA Detected = BCM3413
ADC Clocks aligned
Initializing all 8 downstreams - this takes a while.  Patience, Grasshopper...
1 2 3 4 5 6 7 8 
Creating a new host UTP DQM manager. Instance: 82ed2dcc
Creating a new host UTP DQM manager. Instance: 82ec29dc
Creating a new host UTP DQM manager. Instance: 82ec2914
Powering UP switch. PIN = 14
Creating a new host MSG PROC DQM manager. Instance: 82ec2048, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82ec1f80, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82ec1ddc, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82ec1bdc, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host FAP DQM manager. Instance: 82ec19dc
Creating a new host FAP DQM manager. Instance: 82ec17d4
Creating a new host MPEG PROC DQM manager. Instance: 82ec15cc, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Initializing main MEP DQM interrupts.
 b8a01000: 00000008
 b8a01004: 00000000
 b8a01008: 00000008
 b8a0100c: 00000000
 b8a01010: 00000000
 b8a01014: 00000000
 b8a01018: 00000000
 b8a0101c: 00000000
Creating a new host MPEG PROC DQM manager. Instance: 82ec13d4, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Creating a new host MSG PROC DQM manager. Instance: 82ea8a18, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82ea8810, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82ea8758, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82ea6694, DQM_REGS = b8601800, CTRL_REGS = b8601000
Creating a new host MSG PROC DQM manager. Instance: 82ea662c, DQM_REGS = b8601800, CTRL_REGS = b8601000
Register Int Handler: busNo = 1, device = 0
Creating a new host PMC DQM manager. Instance: 82dd2458, DQM_REGS = b8801800, CTRL_REGS = b8801000
wps_main: upnp I/F not up yet...
Creating a new host MPEG PROC DQM manager. Instance: 82aad404, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Creating a new host MPEG PROC DQM manager. Instance: 82949cb8, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
Creating a new host MPEG PROC DQM manager. Instance: 82949c08, DQM_REGS = b8a01800, CTRL_REGS = b8a01000
wps_main: upnp I/F not up yet...
Creating a new host PMC DQM manager. Instance: 82487e84, DQM_REGS = b8801800, CTRL_REGS = b8801000</nowiki>
</WRAP>\\
==== Linux Bootlog ====
<WRAP bootlog>
<nowiki>[    0.000000] Linux version 2.6.30-1.0.10mp4 (dennis@Apple) (gcc version 4.2.3) #1 Thu Dec 24 10:29:57 C5
[    0.000000] BCM93383 reference design prom init                                                                      
[    0.000000] args: 2 0x87000000                                                                                       
[    0.000000] CPU revision is: 00019070 (MIPS 4KEc)                                                                    
[    0.000000] Determined physical RAM map:                                                                             
[    0.000000]  memory: 03e00000 @ 04000000 (usable)                                                                    
[    0.000000] User-defined physical RAM map:                                                                           
[    0.000000]  memory: 03fd0000 @ 04000000 (usable)                                                                    
[    0.000000]  memory: 00000000 @ 00000000 (usable)                                                                    
[    0.000000] Zone PFN ranges:                                                                                         
[    0.000000]   DMA      0x00004000 -> 0x00001000                                                                      
[    0.000000]   Normal   0x00001000 -> 0x00007fd0                                                                      
[    0.000000] Movable zone start PFN for each node                                                                     
[    0.000000] early_node_map[1] active PFN ranges                                                                      
[    0.000000]     0: 0x00004000 -> 0x00007fd0                                                                          
[    0.000000] On node 0 totalpages: 16336                                                                              
[    0.000000] free_area_init_node: node 0, pgdat 8448b360, node_mem_map 844db000                                       
[    0.000000]   Normal zone: 128 pages used for memmap                                                                 
[    0.000000]   Normal zone: 16208 pages, LIFO batch:3                                                                 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16208                               
[    0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=linuxkfs ubi.mtd=linuxapps root=ubi0:rootfs ro noinitr0
[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.                                          
[    0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes                                       
[    0.000000] RCU-based detection of stalled CPUs is enabled.                                                          
[    0.000000] NR_IRQS:128                                                                                              
[    0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)                                                       
[    0.000000] console [ttyS0] enabled                                                                                  
[    0.001000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)                                            
[    0.002000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)                                             
[    0.023000] Memory: 59732k/65344k available (3544k kernel code, 5536k reserved, 1048k data, 136k init, 0k highmem)   
[    0.025000] Calibrating delay loop... 316.41 BogoMIPS (lpj=158208)                                                   
[    0.047000] Mount-cache hash table entries: 512                                                                      
[    0.074000] net_namespace: 748 bytes                                                                                 
[    0.077000] NET: Registered protocol family 16                                                                       
[    0.089000] Added platform devs for chip ID = 0x33830032!                                                            
[    0.169000] bio: create slab <bio-0> at 0                                                                            
[    0.182000] SCSI subsystem initialized                                                                               
[    0.188000] usbcore: registered new interface driver usbfs                                                           
[    0.193000] usbcore: registered new interface driver hub                                                             
[    0.196000] usbcore: registered new device driver usb                                                                
[    0.202000] NET: Registered protocol family 8                                                                        
[    0.203000] NET: Registered protocol family 20                                                                       
[    0.228000] NET: Registered protocol family 2                                                                        
[    0.234000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)                                           
[    0.245000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)                                         
[    0.253000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)                                                 
[    0.259000] TCP: Hash tables configured (established 2048 bind 2048)                                                 
[    0.265000] TCP reno registered                                                                                      
[    0.270000] NET: Registered protocol family 1                                                                        
[    0.293000] squashfs: version 4.0 (2009/01/31) Phillip Lougher                                                       
[    0.299000] squashfs: version 4.0 with LZMA457 ported by BRCM                                                        
[    0.308000] NTFS driver 2.1.29 [Flags: R/W].                                                                         
[    0.313000] JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.                                                     
[    0.321000] fuse init (API version 7.11)                                                                             
[    0.328000] msgmni has been set to 116                                                                               
[    0.335000] alg: No test for cipher_null (cipher_null-generic)                                                       
[    0.342000] alg: No test for ecb(cipher_null) (ecb-cipher_null)                                                      
[    0.350000] alg: No test for digest_null (digest_null-generic)                                                       
[    0.357000] alg: No test for compress_null (compress_null-generic)                                                   
[    0.383000] alg: No test for stdrng (krng)                                                                           
[    0.388000] io scheduler noop registered (default)                                                                   
[    0.413000] PPP generic driver version 2.4.2                                                                         
[    0.422000] NET: Registered protocol family 24                                                                       
[    0.443000] <<<<<<<<< rpc_init >>>>>>>>>                                                                             
[    0.447000] rpc_register_functions registered service 0: 1 functions                                                 
[    0.457000] rpc_init send handshake message                                                                          
[    0.462000] bcm9338x_mtd driver v1.0                                                                                 
[    0.465000] <<<<<<<<< rpc_init >>>>>>>>>                                                                             
[    0.469000] Benign Warning: Redundant rpc_init()                                                                     
[    0.474000] <<<<< dqm_init_func beef0002 >>>>>                                                                       
[    0.478000] RPC Version 00000003                                                                                     
[    0.482000] DQM Init complete for dqm tunnel 0                                                                       
[    0.486000] <<<<< dqm_init_func beef0001 >>>>>                                                                       
[    0.491000] cpu_idle CPU 0                                                                                           
[    0.494000] Flash device 0:  Nor 4 partitions bs: 00010000 ps: 00000100                                              
[    0.501000] 4 partitions                                                                                             
[    0.503000] mtd   offset     size name                                                                               
[    0.507000]   0 00000000 00010000 bootloader                                                                         
[    0.512000]   1 00010000 00010000 permnv                                                                             
[    0.517000]   2 000c0000 00040000 dynnv                                                                              
[    0.521000]   3 00020000 00010000 vennv                                                                              
[    0.526000] Flash device 1: Nand 6 partitions bs: 00020000 ps: 00000800                                              
[    0.532000] 6 partitions                                                                                             
[    0.535000] mtd   offset     size name                                                                               
[    0.539000]   0 01f40000 00900000 image1                                                                             
[    0.544000]   1 02840000 00900000 image2                                                                             
[    0.612000]   2 03160000 00460000 linux                                                                              
[    0.616000]   3 00020000 01f20000 linuxapps                                                                          
[    0.621000]   4 07de0000 00220000 dhtml                                                                              
[    0.626000]   5 035e0000 047e0000 linuxkfs                                                                           
[    0.630000] Creating 4 MTD partitions on "bcmmtd_vflash_device":                                                     
[    0.636000] 0x000000000000-0x000000010000 : "bootloader"                                                             
[    0.652000] 0x000000010000-0x000000020000 : "permnv"                                                                 
[    0.665000] 0x0000000c0000-0x000000100000 : "dynnv"                                                                  
[    0.679000] 0x000000020000-0x000000030000 : "vennv"                                                                  
[    0.691000] Creating 6 MTD partitions on "bcmmtd_vflash_device":                                                     
[    0.698000] 0x000001f40000-0x000002840000 : "image1"                                                                 
[    0.727000] 0x000002840000-0x000003140000 : "image2"                                                                 
[    0.756000] 0x000003160000-0x0000035c0000 : "linux"                                                                  
[    0.778000] 0x000000020000-0x000001f40000 : "linuxapps"                                                              
[    0.844000] 0x000007de0000-0x000008000000 : "dhtml"                                                                  
[    0.862000] 0x0000035e0000-0x000007dc0000 : "linuxkfs"                                                               
[    0.996000] bcm9338x Linux services init                                                                             
[    1.000000] rpc_register_functions registered service 1: 10 functions                                                
[    1.012000] UBI: attaching mtd9 to ubi0                                                                              
[    1.016000] UBI: physical eraseblock size:   131072 bytes (128 KiB)                                                  
[    1.022000] UBI: logical eraseblock size:    126976 bytes                                                            
[    1.027000] UBI: smallest flash I/O unit:    2048                                                                    
[    1.032000] UBI: VID header offset:          2048 (aligned 2048)                                                     
[    1.038000] UBI: data offset:                4096                                                                    
[   15.373000] rpc_send_request timeouts 1 total timeouts 1 clean 1596                                                  
[   22.039000] rpc_send_request timeouts 1 total timeouts 2 clean 1849                                                  
[   30.045000] UBI: attached mtd9 to ubi0                                                                               
[   30.049000] UBI: MTD device name:            "linuxkfs"                                                              
[   30.054000] UBI: MTD device size:            71 MiB                                                                  
[   30.059000] UBI: number of good PEBs:        575                                                                     
[   30.064000] UBI: number of bad PEBs:         0                                                                       
[   30.068000] UBI: max. allowed volumes:       128                                                                     
[   30.072000] UBI: wear-leveling threshold:    4096                                                                    
[   30.077000] UBI: number of internal volumes: 1                                                                       
[   30.081000] UBI: number of user volumes:     1                                                                       
[   30.086000] UBI: available PEBs:             1                                                                       
[   30.090000] UBI: total number of reserved PEBs: 574                                                                  
[   30.095000] UBI: number of PEBs reserved for bad PEB handling: 5                                                     
[   30.101000] UBI: max/mean erase counter: 1/0                                                                         
[   30.105000] UBI: attaching mtd7 to ubi1                                                                              
[   30.109000] UBI: physical eraseblock size:   131072 bytes (128 KiB)                                                  
[   30.115000] UBI: logical eraseblock size:    126976 bytes                                                            
[   30.120000] UBI: smallest flash I/O unit:    2048                                                                    
[   30.125000] UBI: VID header offset:          2048 (aligned 2048)                                                     
[   30.131000] UBI: data offset:                4096                                                                    
[   30.136000] UBI: background thread "ubi_bgt0d" started, PID 168                                                      
[   41.267000] UBI: attached mtd7 to ubi1                                                                               
[   41.271000] UBI: MTD device name:            "linuxapps"                                                             
[   41.277000] UBI: MTD device size:            31 MiB                                                                  
[   41.281000] UBI: number of good PEBs:        249                                                                     
[   41.286000] UBI: number of bad PEBs:         0                                                                       
[   41.290000] UBI: max. allowed volumes:       128                                                                     
[   41.295000] UBI: wear-leveling threshold:    4096                                                                    
[   41.299000] UBI: number of internal volumes: 1                                                                       
[   41.304000] UBI: number of user volumes:     1                                                                       
[   41.308000] UBI: available PEBs:             0                                                                       
[   41.312000] UBI: total number of reserved PEBs: 249                                                                  
[   41.317000] UBI: number of PEBs reserved for bad PEB handling: 2                                                     
[   41.323000] UBI: max/mean erase counter: 3/2                                                                         
[   41.329000] UBI: background thread "ubi_bgt1d" started, PID 171                                                      
[   41.341000] usbcore: registered new interface driver libusual                                                        
[   41.347000] Serial: BCM63XX driver $Revision: 1.1.1.1 $                                                              
[   41.353000] ttyS0 at MMIO 0xb4e00520 (irq = 11) is a BCM63XX                                                         
[   41.361000] bcmvenet: bcmvenet_probe                                                                                 
[   41.365000] <<<<<<<<< rpc_init >>>>>>>>>                                                                             
[   41.369000] Benign Warning: Redundant rpc_init()                                                                     
[   41.373000] Broadcom Ethernet Network Device v0.1 Dec 24 2015 10:29:13                                               
[   41.387000] bcmvenet_probe getting rpc nonvols                                                                       
[   41.392000] bcmvenet_probe getting mac address                                                                       
[   41.397000] eth0: MAC Address: 10:DA:43:54:D7:AD                                                                     
[   41.402000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver                                               
[   41.408000] EHCI-brcm EHCI-brcm.0: Broadcom STB EHCI                                                                 
[   41.419000] EHCI-brcm EHCI-brcm.0: new USB bus registered, assigned bus number 1                                     
[   41.458000] EHCI-brcm EHCI-brcm.0: irq 32, io mem 0x12e00000                                                         
[   41.470000] EHCI-brcm EHCI-brcm.0: USB 0.0 started, EHCI 1.00                                                        
[   41.479000] usb usb1: configuration #1 chosen from 1 choice                                                          
[   41.488000] hub 1-0:1.0: USB hub found                                                                               
[   41.492000] hub 1-0:1.0: 2 ports detected                                                                            
[   41.509000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver                                                   
[   41.516000] OHCI-brcm OHCI-brcm.0: Broadcom STB OHCI                                                                 
[   41.526000] OHCI-brcm OHCI-brcm.0: new USB bus registered, assigned bus number 2                                     
[   41.534000] OHCI-brcm OHCI-brcm.0: irq 31, io mem 0x12e00100                                                         
[   41.608000] usb usb2: configuration #1 chosen from 1 choice                                                          
[   41.617000] hub 2-0:1.0: USB hub found                                                                               
[   41.621000] hub 2-0:1.0: 2 ports detected                                                                            
[   41.641000] rpc_user_init: registered device class brpc                                                              
[   41.647000] Mirror/redirect action on                                                                                
[   41.650000] u32 classifier                                                                                           
[   41.653000]     input device check on                                                                                
[   41.657000]     Actions configured                                                                                   
[   41.667000] TCP cubic registered                                                                                     
[   41.670000] Initializing XFRM netlink socket                                                                         
[   41.675000] NET: Registered protocol family 10                                                                       
[   41.711000] IPv6 over IPv4 tunneling driver                                                                          
[   41.735000] NET: Registered protocol family 17                                                                       
[   41.739000] NET: Registered protocol family 15                                                                       
[   41.744000] error while creating igmp_snooping proc                                                                  
[   41.749000] Initializing MCPD Module                                                                                 
[   41.757000] RPC: Registered udp transport module.                                                                    
[   41.762000] RPC: Registered tcp transport module.                                                                    
[   41.766000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>                                            
[   41.773000] All bugs added by David S. Miller <davem@redhat.com>                                                     
[   42.061000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"                                                     
[   42.067000] UBIFS: mounted read-only                                                                                 
[   42.071000] UBIFS: file system size:   70344704 bytes (68696 KiB, 67 MiB, 554 LEBs)                                  
[   42.078000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)                                      
[   42.085000] UBIFS: media format:       w4/r0 (latest is w4/r0)                                                       
[   42.091000] UBIFS: default compressor: lzo                                                                           
[   42.095000] UBIFS: reserved for root:  0 bytes (0 KiB)                                                               
[   42.221000] VFS: Mounted root (ubifs filesystem) readonly on device 254:1.                                           
[   42.229000] Freeing unused kernel memory: 136k freed                                                                 
init started: BusyBox v1.19.3 (2015-12-24 10:30:08 CST)                                                                 
starting pid 201, tty '': '/etc/init.d/rcS'                                                                             
                                                                                                                        
Loading drivers and kernel modules...                                                                                   
                                                                                                                        
[   47.841000] Driver 'sd' needs updating - please use bus_type methods                                                 
[   48.807000] Initializing USB Mass Storage driver...                                                                  
[   48.827000] usbcore: registered new interface driver usb-storage                                                     
[   48.845000] USB Mass Storage support registered.                                                                     
Mounting apps partition                                                                                                 
[   50.043000] UBIFS: recovery needed                                                                                   
[   50.268000] UBIFS: recovery completed                                                                                
[   50.272000] UBIFS: mounted UBI device 1, volume 0, name "linuxapps"                                                  
[   50.278000] UBIFS: file system size:   29712384 bytes (29016 KiB, 28 MiB, 234 LEBs)                                  
[   50.286000] UBIFS: journal size:       1523712 bytes (1488 KiB, 1 MiB, 12 LEBs)                                      
[   50.293000] UBIFS: media format:       w4/r0 (latest is w4/r0)                                                       
[   50.299000] UBIFS: default compressor: lzo                                                                           
[   50.303000] UBIFS: reserved for root:  1403389 bytes (1370 KiB)                                                      
starting pid 279, tty '': 'lxginit 2> /dev/ttyS0'                                                                       
starting pid 280, tty '': 'smbapp 2> /dev/ttyS0 '                                                                       
                                                                                                                        
Please press Enter to activate this console. [   50.786000] Sending link up message to app.                             
[   50.799000] Link is up                                                                                               
NAS: Network Attached Storage Control Application [Version 1.3 Build Dec 24 2015 10:37:28]                              
SmbApp: 3G enabled? (0)                                                                                                 
Launching mscapp                                                                                                        
SmbApp: waiting on port 49182 to recvfrom...                                                                            
[   51.528000] GPL_NetUSB: is loaded!                                                                                   
MSC: Media Server Control Application [Version 1.2 Build Dec 24 2015 10:37:28]                                          
MSC: waiting for data on port UDP 49181                                                                                 
[   51.725000]  GPL NetUSB up!                                                                                          
[   51.986000] NetUSB: is loaded!                                                                                       
[   51.999000] NetUSB: module license 'Proprietary' taints kernel.                                                      
[   52.005000] Disabling lock debugging due to kernel taint                                                             
[   52.285000] kc   86 : run_telnetDBGDServer start                                                                     
[   52.291000] kc  223 : init_DebugD end                                                                                
[   52.295000] INFO1773: NetUSB 1.02.17, 0002061E : Sep  4 2012 15:00:00                                                
[   52.301000] INFO1775:  AUTH ISOC                                                                                     
[   52.305000] INFO1776:  MOVE_HEAD filterAudio                                                                         
[   52.310000] INFO0AAB:  --- checkSBusTimeoutThread start ---                                                          
[   52.337000] usbcore: registered new interface driver KC NetUSB General Driver                                        
[   52.354000] INFO0076:  init proc : PAGE_SIZE 4096                                                                    
[   52.360000] INFO1647:  infomap c035f1bc                                                                              
[   52.364000] INFO164A:  sleep to wait eth0 to wake up                                                                 
[   52.369000] INFO02D0:  use dev Name eth0                                                                             
[   52.373000] INFO1653:  sleep to wait eth0 end.                                                                       
[   52.378000] INFO166C:  UDP_BROAD 7423 tcpPort:625868800                                                              
[   52.388000] INFO02D0:  use dev Name eth0                                                                             
[   52.426000] INFO1553: tcpConnector() started...                                                                      
[   55.424000] INFO1430: Bind to eth0                                                                                   
SmbApp: Cmd SendConfig feature 005f                                                                                     
found 0 USB devices                                                                                                     
SmbApp: Nas Enable                                                                                                      
SmbApp: launch_smbd                                                                                                     
smbapp signal SIGALRM                                                                                                   
SmbApp: lanuched smbd at pid 656                                                                                        
SmbApp: Netbios Enable                                                                                                  
SmbApp: launch_nmbd                                                                                                     
SmbApp: lanuched nmbd at pid 677                                                                                        
Launching proftpd                                                                                                       
SmbApp: HTTP Enable                                                                                                     
SmbApp: start proftpd                                                                                                   
Launching proftpd                                                                                                       
SmbApp: ApprovedAll Enabled                                                                                             
SmbApp: ApprovedOnly Disabled                                                                                           
SmbApp: DefaultShareAll Enable                                                                                          
set netbios name BRCM-LVG                                                                                               
set workgroup name WORKGROUP                                                                                            
set admin name admin                                                                                                    
set admin pass                                                                                                          
1970-01-01 00:02:02: (log.c.166) server started                                                                         
_none_ proftpd[694] 0.0.0.0: mod_lang/0.9: unable to scan the localised files in '/opt/toolchains/uclibc-crosstools-gccy
smbapp: Killing nmbd (pid 677)                                                                                          
SmbApp: launch_nmbd                                                                                                     
SmbApp: lanuched nmbd at pid 762                                                                                        
smbapp: Killing smbd (pid 656)                                                                                          
SmbApp: launch_smbd                                                                                                     
SmbApp: lanuched smbd at pid 766                                                                                        
SmbApp: Cmd SendConfig feature 005f                                                                                     
SmbApp: No Feature change                                                                                               
SmbApp: Cmd SendConfig feature 005f                                                                                     
SmbApp: No Feature change                                                                                               
SmbApp: Cmd SendConfig feature 005f                                                                                     
SmbApp: No Feature change                                                                                               
SmbApp: Cmd SendConfig feature 005f                                                                                     
SmbApp: No Feature change                                                                                               
SmbApp: Cmd SendConfig feature 005f                                                                                     
SmbApp: No Feature change                                                                                               
SmbApp: Cmd GetNumDevices = 0                                                                                           
SmbApp: Cmd GetNumDevices = 0                                                                                           
SmbApp: Cmd Disable                                                                                                     
SmbApp: Killed process smbd                                                                                             
SmbApp: Killed process nmbd                                                                                             
SmbApp: Cmd Enable                                                                                                      
SmbApp: executeCmdNasEnable featureBitfield 005f                                                                        
SmbApp: launch_smbd                                                                                                     
SmbApp: lanuched smbd at pid 969                                                                                        
SmbApp: launch_nmbd                                                                                                     
SmbApp: lanuched nmbd at pid 970                                                                                        
                                                                                                                        
starting pid 281, tty '': '/bin/cttyhack /bin/login'                                                                    
(none) login: 
</nowiki>
</WRAP>\\

===== eCos Commands =====
<WRAP bootlog>
<nowiki>Command Table:  Built-in Commands (built-in)

Description:

System-wide, built-in commands that are handled by the Console Thread.  These
commands are always available, regardless of which command table is active.

Available Commands:

!               ?               cd              dir             find_command   
help            history         ls              man             pwd            
syntax          system_time     
------------------------------------------------------------------------------

logout          
----
Command Table:  CM DOCSIS Commands (CM)

Description:

CM DOCSIS Commands

Available Commands:

btcp            con_high        cpuLoad         cpuUtilization  exit           
mbufShow        memShow         mutex_debug     ping            read_memory    
reset           routeShow       socket_debug    stackShow       taskSuspendAll 
usfsShow        version         
----

Available sub-command tables:

[80211_hal] [avs] [cablemedea] [cm_hal] [docsis_ctl] [dtp] [eRouter] 
[event_log] [fam] [itc_hal] [mso] [pingHelper] [power] [snmp] 
[spectrum_analyzer] 

------------------------------------------------------------------------------

Command Table:  802.11 HAL Commands (80211_hal)

Description:

Commands to show/change the 802.11 HAL state.

Available Commands:

acs_cli         dumpHotCache    envram          envrams         hal_show       
led             nvram           pcieDump        pktcToggle      rc             
show            wl              
----

------------------------------------------------------------------------------

Command Table:  AVS Commands (avs)

Description:

Commands to show/change AVS-specific information.

Available Commands:

debug_temp      print_level     pvt             ring48          set_dac        
ssbrosc         step_dac        timeAVS         
----

------------------------------------------------------------------------------

Command Table:  CableMedea Commands (cablemedea)

Description:

CableMedea Command Table

Available Commands:

arp_show        arppacket_show  capt_show       fwr_show        igmpShow       
lan_network_add lan_network_remove              lan_network_show               
lan_route_show  nat_show        traceroute      usfs_show       
----

Available sub-command tables:

[dhcps] [dns] [dnsproxy] [msc] [nas] [natp] [rip] [route] [upnp] [vpn] 

------------------------------------------------------------------------------

Command Table:  Dhcps Commands (dhcps)

Description:

Dhcps Command Table

Available Commands:

add_lease       enable          remove_lease    show            
----

------------------------------------------------------------------------------

Command Table:  Dns Commands (dns)

Description:

Dns Command Table

Available Commands:

dns_debug       dns_show        dnsquery        gethostbyaddr   gethostbyname  
----

------------------------------------------------------------------------------

Command Table:  Dns Proxy Commands (dnsproxy)

Description:

Dns Proxy Command Table

Available Commands:

debug           dnsproxy_show   
----

------------------------------------------------------------------------------

Command Table:  Media Server Control Commands (msc)

Description:

Media Server Control Command Table

Available Commands:

enable          getscanstatus   getstate        rescan          scaninterval   
sendconfig      servername      
----

------------------------------------------------------------------------------

Command Table:  Network Attached Storage Commands (nas)

Description:

NAS Command Table

Available Commands:

addshare        dumpdevices     dumpshares      enable          getdir         
getstate        numdevices      numshares       removeshare     rescandevices  
resetshares     
----

------------------------------------------------------------------------------

Command Table:  Nat Session Manager Commands (natp)

Description:

Commands to show the Nat Session Manager object.

Available Commands:

apiAdd          apiQuery        apiRemove       bins            cache          
counters        debug           diag_output     dma_command     dqm_status     
ffe_inst        ffe_pm          first_entry     flowShow        ignore_list    
msp_call_stack  natp_bypass     natp_promote    perf_counters   
promotion_threshold             psm_hdrs        psm_pkts        reg_dump       
scratch_counters                sessions        show_init       stack_query    
stats           timer_enable    track_sessions  unresolved_dest_macs           
usage_stats     verbose_debug   
----

------------------------------------------------------------------------------

Command Table:  Rip Commands (rip)

Description:

Rip Command Table

Available Commands:

rip_show        
----

------------------------------------------------------------------------------

Command Table:  Route Commands (route)

Description:

Route Command Table

Available Commands:

reload_route_service            route_show      
----

------------------------------------------------------------------------------

Command Table:  Upnp Commands (upnp)

Description:

Upnp Command Table

Available Commands:

control_if      device_discovery                discovery_show  enable         
network_show    notify_show     show            
----

------------------------------------------------------------------------------

Command Table:  VPN Commands (vpn)

Description:

Commands for the VPN library

Available Commands:

dump            ike_test_connect                ike_test_disconnect            
ike_test_start_keyneg           start           stop            
----

------------------------------------------------------------------------------

Command Table:  CM DOCSIS HAL Commands (cm_hal)

Description:

Commands to show/change the CM DOCSIS HAL state.

Available Commands:

D3PowerSave     PowerSave       ackcel_show     add_mcast_dsid  add_reseq_dsid 
cam_dump        center_tuner    channelizer_state               counters       
cpe_add         cpe_del         cpe_max         cpe_print       
delete_mcast_dsid               dpm             drw_show        ds_state       
dsb_reset       dsid_helper     errors          fft             fft_dump       
fft_store       fpga_amp        hal_show        ldaix_read      lna_read       
lna_write       locate_maps     lock_ds         log             mac_diag       
mac_reset       map_lead_time_show              multicast_table multilock_ds   
qam_lock        qosParms        rateshape       sc_dpm          sc_lock        
sc_switch       scan_ds         scan_stop       set_drw         show           
show_halif      tc_counter      transmit        tune            tune_band      
tuner_module    tuner_read      tuner_wideband  tuner_write     
us30_clear_debug_counters       us30_debug_counters             us30_flowsize  
us30_set_debug_flow             us_burst        us_cw_transmit  us_debug       
us_metrics      us_multi_burst  us_multi_tone   us_multi_transmit              
us_reset        us_sweep        us_transmit     utp_status      
----

------------------------------------------------------------------------------

Command Table:  CM DOCSIS Control Thread Commands (docsis_ctl)

Description:

Commands to change the state of the DOCSIS Control thread.

Available Commands:

bpiShow         cfg_hex_show    cfg_tlv_show    ch_state        cm_ctrl        
copy_image      dbc_msg_inject  dload           dsdiag          dsx_show       
event_censor    goto_ds         goto_us         igmpShow        ip_initialize  
ip_show         link_state      log_messages    map_debug       mdd_modify     
mdd_sets_show   modem_caps      nrg_mgmt        override_ucd_max_burst         
publish_event   rate_shaping_enable             reseq_dsid_regress_test        
rng_rsp         scan_stop       showFlows       stop_download   ucdShow        
ucddiag         up_dis          us_phy_oh_show  us_target_mset  usdiag         
----

Available sub-command tables:


------------------------------------------------------------------------------

Command Table:  DTP Commands (dtp)

Description:

Commands to control DTP state.

Available Commands:

add_dsg_mac     change_dsid     clstr_lo_wmrk   create_dsid     del_dsg_mac    
delete_dsid     dsid_hi_wmrk    dump_dsg_macs   max_tokens      ping_dtp       
read_counter    set_dsg_primary_channel         show            sim_rx         
stack_check     test            
----

------------------------------------------------------------------------------

Command Table:  eRouter Commands (eRouter)

Description:

eRouter Command Table

Available Commands:

nd_show         ra_test         solicit         
----

Available sub-command tables:

[dhcpv6s] 

------------------------------------------------------------------------------

Command Table:  DHCPv6 Server Commands (dhcpv6s)

Description:

DHCPv6 Server Command Table

Available Commands:

DhcpV6Config    UpdateServers   address_pools   pd_test         prefix_pool    
----

------------------------------------------------------------------------------

Command Table:  Event Log commands (event_log)

Description:

Commands to manipulate the Event Log

Available Commands:

log_event       show            silent          stop_stress     syslog         
verbose_show    
----

------------------------------------------------------------------------------

Command Table:  Forward Assist Manager Commands (fam)

Description:

Commands to show the ForwardAssistManager object.

Available Commands:

api             benchmark       set             show            vlan           
----

Available sub-command tables:

[compilers] [filters] [trees] 

------------------------------------------------------------------------------

Command Table:  FlexibleFilterCompiler Commands (compilers)

Description:

Commands to show FlexibleFilterTree objects.

Available Commands:

show            
----

------------------------------------------------------------------------------

Command Table:  FlexibleFilter Commands (filters)

Description:

Commands to show FlexibleFilterTree objects.

Available Commands:

show            
----

------------------------------------------------------------------------------

Command Table:  FlexibleFilterTree Commands (trees)

Description:

Commands to show FlexibleFilterTree objects.

Available Commands:

show            
----

------------------------------------------------------------------------------

Command Table:  ITC HAL Commands (itc_hal)

Description:

Commands to show/change the Ethernet HAL state.

Available Commands:

down            hal_show        passwd          reboot_linux    remoteapi      
show            shutdown_linux  thread_debug    thread_show     up             
----

------------------------------------------------------------------------------

Command Table:  Mso Commands (mso)

Description:

Commands to show/change the MSO specific information.

Available Commands:

arp_clear       arp_show        auth_type       configurator    console_prompt 
defaults        dhcp_enable     dhcp_pool       dhcp_server     dns_server     
enable_wireless exit_monitor    fac_reset       firewall_enable host_name      
lan_switch_enable               lan_switch_speed                load_config    
monitor         nat_enable      pflt_disable    pflt_enable     pflt_show      
pfwd_disable    pfwd_enable     pfwd_show       reset           rg_mode_switch 
rip2_debug      rip2_interval   rip2_keyid      rip2_keystr     rip2_md5       
rip2_server     rip_enable      routeShow       show_all        static_ip1     
static_ip2      static_ip3      static_ip_mode  tac_enable      tac_key        
tac_md5         tac_method      tac_server      traceroute      vpnstatus      
----

------------------------------------------------------------------------------

Command Table:  Ping Commands (pingHelper)

Description:

Ping Helper Thread settings and commands.  These commands allow you to set the
ping utility up with precise control over packet sizes, timeout values, etc.

Available Commands:

all_sizes       end_size        hs_nowait       hs_wait         ip_address     
ip_stack        ip_sweep        number_of_pings ping            
restore_defaults                show_settings   start_size      stats          
step_amount     stop            time_between_pings              verbosity      
verify_enable   wait_enable     wait_time       
----

------------------------------------------------------------------------------

Command Table:  Power Management Commands (power)

Description:

Commands to show/change power management specific information.

Available Commands:

client          debug           level           new_client      show           
----

------------------------------------------------------------------------------

Command Table:  SNMP Commands (snmp)

Description:

SNMP commands.

Available Commands:

ch_cfgfile      cm_cfgfile      cm_filter_test  coex_community  debug          
get             group_members   install_group   key_v3          lan_snmpAccess 
log             n2m             notify_setup    parent_chain    reset          
set             severities      show            test            throttle       
tlv_55          trap            view_v1v2       
----

------------------------------------------------------------------------------

Command Table:  Spectrum Analyzer Commands (spectrum_analyzer)

Description:

Commands to show/change spectrum analyzer specific information.

Available Commands:

cmp_period      cmp_rng         debug           diag_mode       diff_thold     
enable_measurement              ref_cmp         ref_ffts        ref_iters      
ref_samples     ref_store       show            window_function 
----

------------------------------------------------------------------------------
</nowiki>
</WRAP>\\

===== eCos Commands In Detail =====
<WRAP bootlog>
<nowiki>COMMAND:  !

USAGE:  !  [Number{0..15}] [command{31}]

DESCRIPTION:
Executes the last command that was entered.  If a command (or history number) 
is specified, then it executes that command from the history buffer.  This 
works like the Unix '!' command

EXAMPLES:
!     -- This repeats the last command that was entered.
! cd  -- This repeats the last 'cd' command that was entered.

-----------------------------------------------------------------------------

COMMAND:  ?

USAGE:  ?  [-t|-l|-s|-i|-a|-lr] [command [...]{126}]

DESCRIPTION:
Alias for 'help'.  Type 'help help' for more information.

EXAMPLES:
No examples available...

-----------------------------------------------------------------------------

COMMAND:  cd

USAGE:  cd  [subtable | .. | \ | /{31}]

DESCRIPTION:
Sets the specified command table as the active table.  This works like the 
DOS or Unix 'cd' command where '..' takes you to the previous table, and '\' 
or '/' takes you to the root table.  If no parameters are specified, then it 
shows the name of the currently active command table.

EXAMPLES:
cd classifiers  -- Makes the specified subtable the active command table.
cd \            -- Makes the main command table active.
cd ..           -- Makes the previous (parent) command table active.
cd              -- Shows the name of the active command table.
cd \non\doc     -- You can specify partial names, and mutliple subdirs.

-----------------------------------------------------------------------------

COMMAND:  dir

USAGE:  dir  [-t|-l|-s|-i|-a|-lr] [command [...]{126}]

DESCRIPTION:
Alias for 'help'.  Type 'help help' for more information.

EXAMPLES:
No examples available...

-----------------------------------------------------------------------------

COMMAND:  find_command

USAGE:  find_command  command{31}

DESCRIPTION:
Displays the name of all subdirectories which contain the specified command.

EXAMPLES:
find_command show  -- 

-----------------------------------------------------------------------------

COMMAND:  help

USAGE:  help  [-t|-l|-s|-i|-a|-lr] [command [...]{126}]

DESCRIPTION:
Shows usage information about the specified command(s), or lists the set of 
commands available in the active table.  If no parameters are specified, then 
an abbreviated list of all commands and subtables is displayed.

     -t  -- Shows the entire tree of command tables and commands (in 
            abbreviated form).
     -l  -- Shows detailed information about all commands and subtables (this 
            can print a LOT of information)!
     -s  -- Shows detailed information on just the subtables.
     -i  -- Shows detailed information on just the registered instances for 
            the active table.
     -a  -- Does everything that the -l, -s, and -i options do.

Command is the name (or partial name) of one or more commands and subtables 
for which you want detailed help to be displayed.

EXAMPLES:
help            -- This shows an abbreviated list of all commands and 
                   subtables.
help cd         -- This shows detailed help on the 'cd' command.
help cd ! diag  -- This shows detailed help on the 2 commands and subtable 
                   listed.
help -l         -- Shows detailed help on all available commands and 
                   subtables.

-----------------------------------------------------------------------------

COMMAND:  history

USAGE:  history 

DESCRIPTION:
Shows a list of commands that were previously typed.

EXAMPLES:
history  -- 

-----------------------------------------------------------------------------

COMMAND:  ls

USAGE:  ls  [-t|-l|-s|-i|-a|-lr] [command [...]{126}]

DESCRIPTION:
Alias for 'help'.  Type 'help help' for more information.

EXAMPLES:
No examples available...

-----------------------------------------------------------------------------

COMMAND:  man

USAGE:  man  [-t|-l|-s|-i|-a|-lr] [command [...]{126}]

DESCRIPTION:
Alias for 'help'.  Type 'help help' for more information.

EXAMPLES:
No examples available...

-----------------------------------------------------------------------------

COMMAND:  pwd

USAGE:  pwd 

DESCRIPTION:
Shows the name of the currently active command table.  This is like the Unix 
'pwd' command.

EXAMPLES:
pwd  -- 

-----------------------------------------------------------------------------

COMMAND:  syntax

USAGE:  syntax 

DESCRIPTION:
Displays detailed information on command line syntax and how the parser 
works.

EXAMPLES:
syntax  -- 

-----------------------------------------------------------------------------

COMMAND:  system_time

USAGE:  system_time 

DESCRIPTION:
Displays the current system millisecond tick counter.

EXAMPLES:
system_time  -- 

-----------------------------------------------------------------------------

COMMAND:  logout

USAGE:  logout 

DESCRIPTION:
For Telnet clients, this lets the user log out cleanly.

EXAMPLES:
logout  -- 

-----------------------------------------------------------------------------

COMMAND:  btcp

USAGE:  btcp  [{31}] [{31}]

DESCRIPTION:
{No command help available...}

EXAMPLES:


-----------------------------------------------------------------------------

COMMAND:  con_high

USAGE:  con_high 

DESCRIPTION:
Boosts the console thread priority so that you can use the console while the 
system is busy.  Normally, the console priority is low so that it doesn't 
interfere with normal system operation.

EXAMPLES:
con_high  -- 

-----------------------------------------------------------------------------

COMMAND:  cpuLoad

USAGE:  cpuLoad  milliseconds{0..10000}

DESCRIPTION:
Displays current CPU load, averaged over the specified number of 
milliseconds.  Value of 0 will toggle start/stop control of load calculation.

EXAMPLES:
cpuLoad  -- 

-----------------------------------------------------------------------------

COMMAND:  cpuUtilization

USAGE:  cpuUtilization  milliseconds{0..10000}

DESCRIPTION:
Displays CPU Utilization over the specified number of milliseconds.  Value of 
0 will toggle start/stop control of utilization calculation.

EXAMPLES:
cpuUtilization  -- 

-----------------------------------------------------------------------------

COMMAND:  exit

USAGE:  exit 

DESCRIPTION:
For Telnet/ssh clients, this lets the user log out cleanly.

EXAMPLES:
exit

-----------------------------------------------------------------------------

COMMAND:  logout

USAGE:  logout 

DESCRIPTION:
For Telnet clients, this lets the user log out cleanly.

EXAMPLES:
logout  -- 

-----------------------------------------------------------------------------

COMMAND:  mbufShow

USAGE:  mbufShow 

DESCRIPTION:
Displays current mbuf allocation.

EXAMPLES:
mbufShow  -- 

-----------------------------------------------------------------------------

COMMAND:  memShow

USAGE:  memShow 

DESCRIPTION:
Displays current memory allocation.

EXAMPLES:
memShow  -- 

-----------------------------------------------------------------------------

COMMAND:  mutex_debug

USAGE:  mutex_debug 

DESCRIPTION:
Shows mutex debug information for debugging deadlocks.

EXAMPLES:
mutex_debug

-----------------------------------------------------------------------------

COMMAND:  ping

USAGE:  ping  IpAddress

DESCRIPTION:
Pings the specified target IP address, sending 3 64-byte packets, and waiting 
up to 5 seconds for a response.  This is a basic 'standard' ping.  For more 
options or control over ping parameters and behavior, you will need to go to 
the Ping Command table ('cd pingHelper').

In order for this to work, the CM must either have successfully completed 
DHCP, or must otherwise have been configured with a valid IP address.

Note that this command causes the ping options to be reset to their default 
state.

This may be disabled if the platform doesn't provide an implementation of 
ping.

EXAMPLES:
ping 11.24.4.3  -- Ping IP address 11.24.4.3.

-----------------------------------------------------------------------------

COMMAND:  read_memory

USAGE:  read_memory  [-p] [-c] [-s ElementSize{1..4}] [-n NumberOfBytes{1..16384}] [StartAddress]

DESCRIPTION:
Displays the contents of memory (in hex and ASCII) to the console.

  StartAddress : the address to start displaying (can be memory, registers,
                 etc).
  -s : sets the element size to be read (1, 2, or 4 bytes).  Most useful for
       registers; defaults to 1.
  -n : sets the number of bytes to be read.  Defaults to 16.  Note that this
       will always be padded out to a multiple of the element size.
  -c : increments the start address by the number of bytes before reading.
       This is most useful for continuing the previous read (with the same
       parameters).
  -p : prints the current options (which would be used if not otherwise
       supplied).

If no parameters are specified, it will perform the last read again.

NOTE - the parameters are remembered from one read to the next; e.g. if you 
set the element size to 4 bytes, then all subsequent reads will use this, 
unless explicitly overridden.

WARNING - it may be possible to make the system hang or crash if you read 
from an illegal address!

EXAMPLES:
read_memory -s 4 -n 64 0x80001234  -- Reads 64 bytes as 32-bit values.
read_memory -n 32 0x80001234       -- Reads 32 bytes starting with the 
                                      specified address.
read_memory -c                     -- Reads the next 32 bytes, continuing 
                                      from the previous read.

-----------------------------------------------------------------------------

COMMAND:  reset

USAGE:  reset 

DESCRIPTION:
Causes the application to exit, shutting everything down and cleaning up 
resources.  On embedded platforms, this usually also triggers the internal 
CPU reset logic, causing the h/w to reboot.

EXAMPLES:
reset  -- 

-----------------------------------------------------------------------------

COMMAND:  routeShow

USAGE:  routeShow 

DESCRIPTION:
Displays current routing information.

EXAMPLES:
routeShow  -- 

-----------------------------------------------------------------------------

COMMAND:  socket_debug

USAGE:  socket_debug 

DESCRIPTION:
Shows socket debug information for debugging socket leaks.

EXAMPLES:
socket_debug

-----------------------------------------------------------------------------

COMMAND:  stackShow

USAGE:  stackShow 

DESCRIPTION:
Displays current tasks stack information.

EXAMPLES:
stackShow  -- 

-----------------------------------------------------------------------------

COMMAND:  taskSuspendAll

USAGE:  taskSuspendAll 

DESCRIPTION:
Suspends all tasks.

EXAMPLES:
taskSuspendAll  -- 

-----------------------------------------------------------------------------

COMMAND:  usfsShow

USAGE:  usfsShow 

DESCRIPTION:
Displays the current USFS Table.

EXAMPLES:
usfsShow  -- 

-----------------------------------------------------------------------------

COMMAND:  version

USAGE:  version 

DESCRIPTION:
Displays the current software version and feature codes by printing the 
startup banner.  This allows the user to view the current version information 
without having to restart the application.

EXAMPLES:
version  -- 

-----------------------------------------------------------------------------

Command Table:  802.11 HAL Commands (80211_hal)

Description:

Commands to show/change the 802.11 HAL state.

-----------------------------------------------------------------------------

Command Table:  HeapManager Commands (HeapManager)

Description:

Broadcom Heap Manager (malloc/free) settings and commands.

-----------------------------------------------------------------------------

Command Table:  HostDqm Interface Commands (HostDqm)

Description:

Commands to show/change the HostDqm IF state.

-----------------------------------------------------------------------------

Command Table:  AVS Commands (avs)

Description:

Commands to show/change AVS-specific information.

-----------------------------------------------------------------------------

Command Table:  CableMedea Commands (cablemedea)

Description:

CableMedea Command Table

-----------------------------------------------------------------------------

Command Table:  CM DOCSIS HAL Commands (cm_hal)

Description:

Commands to show/change the CM DOCSIS HAL state.

-----------------------------------------------------------------------------

Command Table:  CM DOCSIS Control Thread Commands (docsis_ctl)

Description:

Commands to change the state of the DOCSIS Control thread.

-----------------------------------------------------------------------------

Command Table:  DTP Commands (dtp)

Description:

Commands to control DTP state.

-----------------------------------------------------------------------------

Command Table:  eRouter Commands (eRouter)

Description:

eRouter Command Table

-----------------------------------------------------------------------------

Command Table:  Embedded Target Commands (embedded_target)

Description:

Commands to control the embedded target platform.

-----------------------------------------------------------------------------

Command Table:  Ethernet HAL Commands (enet_hal)

Description:

Commands to show/change the Ethernet HAL state.

-----------------------------------------------------------------------------

Command Table:  Event Log commands (event_log)

Description:

Commands to manipulate the Event Log

-----------------------------------------------------------------------------

Command Table:  Forward Assist Manager Commands (fam)

Description:

Commands to show the ForwardAssistManager object.

-----------------------------------------------------------------------------

Command Table:  Flash Driver Commands (flash)

Description:

Commands to control the flash device driver.

-----------------------------------------------------------------------------

Command Table:  Forwarder Commands (forwarder)

Description:

Commands to show/change the Forwarder state.

-----------------------------------------------------------------------------

Command Table:  FTP Lite Client Commands (ftpLite)

Description:

FTP Lite Client settings and commands. These commands allows you to configure the FTP Lite Client.

-----------------------------------------------------------------------------

Command Table:  IP Stack HAL Commands (ip_hal)

Description:

Commands to manage IP stacks and related tasks.

-----------------------------------------------------------------------------

Command Table:  ITC HAL Commands (itc_hal)

Description:

Commands to show/change the Ethernet HAL state.

-----------------------------------------------------------------------------

Command Table:  Message Log Settings Commands (msgLog)

Description:

Commands for changing Message Log Settings.  These commands allow you enable
and disable display fields and severity levels for individual objects or for
groups of objects.

-----------------------------------------------------------------------------

Command Table:  Mso Commands (mso)

Description:

Commands to show/change the MSO specific information.

-----------------------------------------------------------------------------

Command Table:  Non-Volatile Settings Commands (non-vol)

Description:

Commands to change the non-volatile settings for the application.

-----------------------------------------------------------------------------

Command Table:  Ping Commands (pingHelper)

Description:

Ping Helper Thread settings and commands.  These commands allow you to set the
ping utility up with precise control over packet sizes, timeout values, etc.

-----------------------------------------------------------------------------

Command Table:  Power Management Commands (power)

Description:

Commands to show/change power management specific information.

-----------------------------------------------------------------------------

Command Table:  SNMP Commands (snmp)

Description:

SNMP commands.

-----------------------------------------------------------------------------

Command Table:  Snoop Commands (snoop)

Description:

Commands to show/change the state of Snoop objects.

-----------------------------------------------------------------------------

Command Table:  Spectrum Analyzer Commands (spectrum_analyzer)

Description:

Commands to show/change spectrum analyzer specific information.

-----------------------------------------------------------------------------
</nowiki>
</WRAP>\\


===== Notes =====
Use username: MSO, password: changeme when telneting to the eCos side at 192.168.0.1.
To stop scanning once logged in, type /cm_hal/scan_stop.

Mount the Linux file system trick:

http://www.haxorware.com/forums/archive/index.php?thread-3419.html
===== Tags =====
[[meta:tags|How to add tags]]
{{tag>BCM3383 8flash 128NAND 128ram unsupported}}
bcm3383 8Flash 128nand 128ram Unsupported devices