User Tools

Site Tools


toh:netcomm:nb604n

Netcomm NB604N

DEVICE INTERFACE

  4 x 10/100Mbps LAN ports
  1 x RJ11 DSL interface (ADSL2+)
  1 x USB 2.0 port – for external Hard Disk Drive Storage
  2 x 2 external WiFi antennas

WIRELESS

  Supports IEEE 802.11n (draft 2.0), IEEE 802.11g and IEEE 802.11b
  Data Rates: Up to 300Mbps for 802.11n, up to 54Mbps for 802.11g and up to 11Mbps for 802.11b
  Antenna Configuration: 2 fixed external antennas (2T2R)
  Operating Channels: 13 channels
  Support 802.1x, WPA/WPA-PSK, WPA2/WPA2-PSK, Mixed WPA/WPA2, and Mixed
  WPA-PSK/WPA2-PSK
  Supports multiple SSIDs
  Supports wireless QoS (WMM)
  Supports wireless protected setup (WPS) with PIN and PBC method

Hardware

Info

Instruction set MIPS
Vendor Broadcom
bootloader cfe
Board ID 96328ang
System-On-Chip BCM6328
CPU @Frq Broadcom4350 V7.5 @320MHz
Flash size 8192 KiB
Flash Chip S25FL064P
RAM size 64 MiB
RAM Chip Winbond W9751G6KB-25
Wireless NIC BCM43225KMLG
Modem xDSL
USB Yes 1 x 2.0
Serial Yes
JTAG No

Photos

Opening the case

Note: This will void your warranty!

  • To remove the cover unscrew 4 screws on base and prise top off (held in place with internal snap in clips)

Main PCB

Main PCB

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial pinout

Sample output

Click to display ⇲

Click to hide ⇱

HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: Wed Mar  9 08:59:51 EST 2011 (root@localhost.localdomain)
Copyright (C) 2000-2009 Broadcom Corporation.

spiclk=40000000
maxoplen=512
flash=S25FL064A size=8MB id=0x010216  sector=64k
 wp1=1c  wp2=1c
HS Serial flash device: name S25FL064A, id 0x010216 size 8192KB
Total Flash size: 8192K with 128 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000


Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-3)                    : 96328ang  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : 00:60:64:82:08:7f  
PSI Size (1-64) KBytes            : 48  
Enable Backup PSI [0|1]           : 1  
System Log Size (0-256) KBytes    : 0  
Main Thread Number [0|1]          : 0  
BigSmallImg mode [0|1]            : 0  

---cfe_bg_tasklist and cfe_bg_args is  ---cfe_bg_tasklist and cfe_bg_args is  send udp message finished.
Not response, auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
---cfe_bg_tasklist and cfe_bg_args is
CFE> 
web info: Waiting for connection on socket 0.

CFE> 

Information

Bootloader

It's possible to bring up the CFE web interface

Tags

toh/netcomm/nb604n.txt · Last modified: 2018/12/29 05:27 by jtan