MikroTik RBwAPG-5HacD2HnD (wAP AC)

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Weatherproof dual-chain dual-band 2.4/5 GHz Wi-Fi AP, with two GbE ports, ceiling/wall mounted, based on powerful quad-core ARM CPU with HW accelerated encryption support.

Not supported.

OpenWrt forum thread: New wAP AC

CPU Ram Flash Network WLAN DC jack Serial
IPQ-4018 @716 MHz 128 MiB 16 MiB 2x 10/100/1000 abgnac Yes onboard dots
Architecture ARM 32bit
Vendor Qualcomm
Bootloader RouterBoot
System-On-Chip IPQ-4018
CPU/Speed 716 MHz
Flash-Chip Winbond W25Q128JVSM
Flash size 16 MiB
RAM 128 MiB
Wireless IPQ-4018 2.4GHz/5GHz 802.11b/g/n/a/n/ac
Wi-Fi Generation 2.4 GHz → WiFi 4, 5 GHz → Wi-Fi 5
Ethernet 2x 10/100/1000 Mbit/s w/ vlan support
Switch IPQ-4018 (SOC integrated)
USB No
Serial Yes, onboard dots
Powering DC jack, PoE-IN
Ingress Protection IP55

Loosen screws.

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

Serial connection parameters
for MikroTik wAP AC

COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE


[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.52 (pdvalck@cassiopeia) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14057-a28b8fecf6)) #0 SMP Thu Aug 6 10:54:51 2020 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Mikrotik hAP ac2 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 32256 [ 0.000000] Normal zone: 284 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32256 pages, LIFO batch:7 [ 0.000000] percpu: Embedded 15 pages/cpu s30028 r8192 d23220 u61440 [ 0.000000] pcpu-alloc: s30028 r8192 d23220 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 31972 [ 0.000000] Kernel command line: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 118824K/129024K available (5458K kernel code, 181K rwdata, 1452K rodata, 1024K init, 230K bss, 10200K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x2f0/0x498 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000021] Switching to timer-based delay loop, resolution 20ns [ 0.000226] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000242] pid_max: default: 32768 minimum: 301 [ 0.000440] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000459] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001552] CPU: Testing write buffer coherency: ok [ 0.002698] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.002847] rcu: Hierarchical SRCU implementation. [ 0.003330] smp: Bringing up secondary CPUs ... [ 0.006618] smp: Brought up 1 node, 4 CPUs [ 0.006640] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.006648] CPU: All CPU(s) started in SVC mode. [ 0.011034] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.011205] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.011233] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.011585] pinctrl core: initialized pinctrl subsystem [ 0.012769] NET: Registered protocol family 16 [ 0.013188] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.014478] cpuidle: using governor ladder [ 0.014527] cpuidle: using governor menu [ 0.019536] GPIO line 414 (enable USB power) hogged as output/high [ 0.035265] cryptd: max_cpu_qlen set to 1000 [ 0.038961] usbcore: registered new interface driver usbfs [ 0.039032] usbcore: registered new interface driver hub [ 0.039127] usbcore: registered new device driver usb [ 0.039178] pps_core: LinuxPPS API ver. 1 registered [ 0.039189] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.039215] PTP clock support registered [ 0.041008] clocksource: Switched to clocksource arch_sys_counter [ 0.041869] thermal_sys: Registered thermal governor 'step_wise' [ 0.042188] NET: Registered protocol family 2 [ 0.042868] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.042909] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.042940] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.042969] TCP: Hash tables configured (established 1024 bind 1024) [ 0.043116] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.043159] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.043413] NET: Registered protocol family 1 [ 0.043456] PCI: CLS 0 bytes, default 64 [ 0.045568] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.051494] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.051510] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.106102] bam-dma-engine 8e04000.dma: num-channels unspecified in dt [ 0.106125] bam-dma-engine 8e04000.dma: num-ees unspecified in dt [ 0.106853] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.106939] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.107020] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.107111] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.107432] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.108054] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.108101] msm_serial 78af000.serial: uartclk = 1843200 [ 0.108153] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM [ 0.108182] msm_serial: console setup on port #0 [ 0.582086] printk: console [ttyMSM0] enabled [ 0.587006] msm_serial: driver initialized [ 0.596461] loop: module loaded [ 0.597603] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 0.605614] random: fast init done [ 0.609224] spi-nor spi0.0: w25q128jv (16384 Kbytes) [ 0.624783] 1 routerbootpart partitions found on MTD device spi0.0 [ 0.624811] Creating 1 MTD partitions on "spi0.0": [ 0.629861] 0x000000000000-0x000001000000 : "partitions" [ 0.635776] 5 routerbootpart partitions found on MTD device partitions [ 0.640098] Creating 5 MTD partitions on "partitions": [ 0.646499] 0x000000080000-0x00000008e000 : "RouterBoot" [ 0.652432] 0x00000008e000-0x00000008f000 : "hard_config" [ 0.657818] 0x000000090000-0x000000097c6e : "dtb_config" [ 0.663251] 0x0000000bd000-0x0000000be000 : "soft_config" [ 0.668546] 0x000000100000-0x000001000000 : "firmware" [ 0.745113] 2 minor-fw partitions found on MTD device firmware [ 0.745146] Creating 2 MTD partitions on "firmware": [ 0.749848] 0x000000000000-0x000000350000 : "kernel" [ 0.755861] 0x000000350000-0x000000f00000 : "rootfs" [ 0.760741] mtd: device 7 (rootfs) set to be root filesystem [ 0.765183] 1 squashfs-split partitions found on MTD device rootfs [ 0.770511] 0x0000006ba000-0x000000f00000 : "rootfs_data" [ 0.778203] libphy: ipq40xx_mdio: probed [ 0.813599] ESS reset ok! [ 0.846655] ESS reset ok! [ 1.264880] libphy: Fixed MDIO Bus: probed [ 1.265916] EDMA using MAC@ - using [ 1.265929] ae:41:66:b8:a3:03 [ 1.272196] EDMA using MAC@ - using [ 1.272209] 42:7a:47:9f:42:50 [ 1.280480] i2c /dev entries driver [ 1.282947] sdhci: Secure Digital Host Controller Interface driver [ 1.284103] sdhci: Copyright(c) Pierre Ossman [ 1.290349] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.298543] MikroTik RouterBOARD hardware configuration sysfs driver v0.05 [ 1.301638] MikroTik RouterBOARD software configuration sysfs driver v0.03 [ 1.308307] NET: Registered protocol family 10 [ 1.315550] Segment Routing with IPv6 [ 1.318562] NET: Registered protocol family 17 [ 1.322308] 8021q: 802.1Q VLAN Support v1.8 [ 1.326575] Registering SWP/SWPB emulation handler [ 1.341827] hctosys: unable to open rtc device (rtc0) [ 1.346509] VFS: Mounted root (squashfs filesystem) readonly on device 31:7. [ 1.348187] Freeing unused kernel memory: 1024K [ 1.404494] Run /sbin/init as init process [ 2.151795] init: Console is alive [ 2.152108] init: - watchdog - [ 3.244084] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.293713] dwc3-qcom 8af8800.usb3: IRQ hs_phy_irq not found [ 3.293755] dwc3-qcom 8af8800.usb3: IRQ dp_hs_phy_irq not found [ 3.298449] dwc3-qcom 8af8800.usb3: IRQ dm_hs_phy_irq not found [ 3.304175] dwc3-qcom 8af8800.usb3: IRQ ss_phy_irq not found [ 3.311210] dwc3-qcom 60f8800.usb2: IRQ hs_phy_irq not found [ 3.315898] dwc3-qcom 60f8800.usb2: IRQ dp_hs_phy_irq not found [ 3.321604] dwc3-qcom 60f8800.usb2: IRQ dm_hs_phy_irq not found [ 3.327180] dwc3-qcom 60f8800.usb2: IRQ ss_phy_irq not found [ 3.336932] dwc3 8a00000.dwc3: Failed to get clk 'ref': -2 [ 3.486061] dwc3 6000000.dwc3: Failed to get clk 'ref': -2 [ 3.626444] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.626518] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.631175] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000000002010010 [ 3.638477] xhci-hcd xhci-hcd.0.auto: irq 94, io mem 0x08a00000 [ 3.648756] hub 1-0:1.0: USB hub found [ 3.653753] hub 1-0:1.0: 1 port detected [ 3.657827] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.661642] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.666874] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.675932] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.681636] hub 2-0:1.0: USB hub found [ 3.689300] hub 2-0:1.0: 1 port detected [ 3.693361] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.696915] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 3.702495] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000000002010010 [ 3.709814] xhci-hcd xhci-hcd.1.auto: irq 95, io mem 0x06000000 [ 3.723193] hub 3-0:1.0: USB hub found [ 3.725071] hub 3-0:1.0: 1 port detected [ 3.729182] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.732985] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 3.738227] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.745918] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.752960] hub 4-0:1.0: USB hub found [ 3.760663] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.766349] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.774181] init: - preinit - [ 4.258321] random: crng init done [ 5.320101] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.491675] jffs2: notice: (199) jffs2_build_xattr_subsystem: complete building xattr subsystem, 20 of xdatum (16 unchecked, 4 orphan) and 24 of xref (2 dead, 2 orphan) found. [ 10.502201] mount_root: switching to jffs2 overlay [ 10.868234] overlayfs: upper fs does not support tmpfile. [ 10.896548] urandom-seed: Seeding with /etc/urandom.seed [ 11.002724] procd: - early - [ 11.002874] procd: - watchdog - [ 11.600426] procd: - watchdog - [ 11.603988] procd: - ubus - [ 11.693220] procd: - init - [ 12.132092] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.168587] urngd: v1.0.2 started. [ 12.190002] Mirror/redirect action on [ 12.199323] u32 classifier [ 12.199351] input device check on [ 12.200921] Actions configured [ 12.212058] Loading modules backported from Linux version v5.8-rc2-0-g48778464bb7d [ 12.212095] Backport generated by backports.git v5.8-rc2-1-0-g7a69429b [ 12.246865] xt_time: kernel timezone is -0000 [ 12.289944] PPP generic driver version 2.4.2 [ 12.291232] NET: Registered protocol family 24 [ 12.324429] ath10k_mac_create, priv_size: 924 hw: 6c133fd2 hw->priv: 789bac6d [ 13.795880] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 13.795933] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 13.808803] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-013-d81f62d97 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 adcbecaa [ 13.853826] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16 crc32 24cecd7f [ 15.154749] ath10k_ahb a000000.wifi: unsupported HTC service id: 1536 [ 15.156231] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 15.160182] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 15.196794] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 15.197748] ath10k_ahb a000000.wifi: wmi print 'free: 53204 iram: 13416 sram: 35752' [ 15.404650] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 15.593426] ath: EEPROM regdomain sanitized [ 15.593526] ath: EEPROM regdomain: 0x64 [ 15.593578] ath: EEPROM indicates we should expect a direct regpair map [ 15.593716] ath: Country alpha2 being used: 00 [ 15.593770] ath: Regpair used: 0x64 [ 15.628959] ath10k_mac_create, priv_size: 924 hw: 0e4268dd hw->priv: ea4d8b9f [ 16.840323] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 16.840386] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 16.853398] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-013-d81f62d97 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 adcbecaa [ 16.904240] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17 crc32 24cecd7f [ 18.211999] ath10k_ahb a800000.wifi: unsupported HTC service id: 1536 [ 18.213244] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 18.217433] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 18.254429] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 18.255373] ath10k_ahb a800000.wifi: wmi print 'free: 53204 iram: 13416 sram: 35752' [ 18.379579] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 18.490351] ath: EEPROM regdomain sanitized [ 18.490453] ath: EEPROM regdomain: 0x64 [ 18.490508] ath: EEPROM indicates we should expect a direct regpair map [ 18.490650] ath: Country alpha2 being used: 00 [ 18.490702] ath: Regpair used: 0x64 [ 18.535576] kmodloader: done loading kernel modules from /etc/modules.d/* [ 23.714339] br-lan: port 1(eth0) entered blocking state [ 23.714377] br-lan: port 1(eth0) entered disabled state [ 23.718849] device eth0 entered promiscuous mode [ 23.739678] ess_edma c080000.edma: eth1: GMAC Link is down [ 23.744534] br-wan: port 1(eth1) entered blocking state [ 23.744598] br-wan: port 1(eth1) entered disabled state [ 23.749785] device eth1 entered promiscuous mode [ 24.791572] br-lan: port 1(eth0) entered blocking state [ 24.791618] br-lan: port 1(eth0) entered forwarding state [ 24.796626] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 26.433845] ath10k_ahb a800000.wifi: unsupported HTC service id: 1536 [ 26.434039] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 26.439284] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 26.476309] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 26.477366] ath10k_ahb a800000.wifi: wmi print 'free: 53204 iram: 13416 sram: 35752' [ 26.762347] ath10k_ahb a800000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 26.790232] br-wan: port 2(wlan1) entered blocking state [ 26.790288] br-wan: port 2(wlan1) entered disabled state [ 26.795423] device wlan1 entered promiscuous mode [ 26.872357] ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000 [ 26.967169] ath10k_ahb a800000.wifi: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 28.313600] ath10k_ahb a000000.wifi: unsupported HTC service id: 1536 [ 28.313832] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 28.319044] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 28.355589] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 28.356634] ath10k_ahb a000000.wifi: wmi print 'free: 53204 iram: 13416 sram: 35752' [ 28.648996] ath10k_ahb a000000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 28.649961] br-wan: port 1(eth1) entered blocking state [ 28.659105] br-wan: port 1(eth1) entered forwarding state [ 28.665977] IPv6: ADDRCONF(NETDEV_CHANGE): br-wan: link becomes ready [ 28.670965] br-wan: port 3(wlan0) entered blocking state [ 28.676062] br-wan: port 3(wlan0) entered disabled state [ 28.681839] device wlan0 entered promiscuous mode [ 29.095523] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 29.096203] br-wan: port 3(wlan0) entered blocking state [ 29.101156] br-wan: port 3(wlan0) entered forwarding state [ 29.117725] br-wan: port 4(wlan0-1) entered blocking state [ 29.117773] br-wan: port 4(wlan0-1) entered disabled state [ 29.122869] device wlan0-1 entered promiscuous mode [ 29.130794] br-wan: port 4(wlan0-1) entered blocking state [ 29.132511] br-wan: port 4(wlan0-1) entered forwarding state [ 29.333540] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready [ 29.710237] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 29.710894] br-wan: port 2(wlan1) entered blocking state [ 29.715829] br-wan: port 2(wlan1) entered forwarding state


the future official supported builds for cAP AC should also work for the new wAP AC

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/04/17 13:42
  • by tmomas