Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:mikrotik:rb951ui [2015/09/08 21:06] – After netbooting WLAN is disabled and only port 2 in the bridge is active for telnetting. Clarified the procedure for newbies to OpenWRT like myself. Synchrotron | toh:mikrotik:rb951ui [2020/08/19 07:49] – [Supported Versions] tpawlowski_ha | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Mikrotik RouterBoard RB951Ui-2HnD ====== | ||
| + | ===== Supported Versions ===== | ||
| + | |||
| + | Warning - Mikrotik has made some changes on the board and recently ordered units are no longer supported. Note: https:// | ||
| + | |||
| + | |||
| + | |||
| + | ---- datatable ---- | ||
| + | cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | ||
| + | headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data | ||
| + | align : c, | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | |||
| + | ===== Hardware Highlights ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | ||
| + | header | ||
| + | align : c, | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | |||
| + | FIXME Conflicting with ToH dataentry -> to be checked | ||
| + | ^ CPU ^ CPU Speed ^ RAM (MB) ^ NAND (MB) ^ Serial Flash ^ Ethernet Switch ^ PoE port ^ Wireless ^ USB ^ UART ^ JTAG ^ | ||
| + | | AR9334 | 600 MHz | 128 (2x W9751G6KB-25) | 128 (1x TC58DVG02D5TA00-ND) | MX25L512E | AR7240 (10M/100M) | 1-in 5-out (500mA) | AR9344-DC3A | 1x 2.0 | 1x onboard | 1x onboard | | ||
| + | |||
| + | |||
| + | Sister product: [[http:// | ||
| + | |||
| + | Please refer to the sister board wiki page [[rb951g_2hnd]] for a description of differences. | ||
| + | |||
| + | Warning! As of 04/02/2020 WiFi is *not* working on rev2 hardware. Check this post for updates: [[https:// | ||
| + | |||
| + | |||
| + | ===== Installation ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| + | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| + | align : c,c,c | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | Please refer to [[toh: | ||
| + | |||
| + | ===== Initial setup ===== | ||
| + | |||
| + | === Leds === | ||
| + | |||
| + | Instructions for setting up LEDs are from 12/2014, but as for v15.05 it seems to be still neccessary to do this. | ||
| + | Anyway, please check first if the LEDs are working as desired (plug devices into ethernet ports, check WLAN activity... etc). | ||
| + | |||
| + | Add these lines to / | ||
| + | |||
| + | config led ' | ||
| + | option trigger ' | ||
| + | option mode 'link tx rx' | ||
| + | option sysfs ' | ||
| + | option name ' | ||
| + | option dev ' | ||
| + | option brightness ' | ||
| + | option default ' | ||
| + | config led ' | ||
| + | option trigger ' | ||
| + | option name ' | ||
| + | option sysfs ' | ||
| + | option dev ' | ||
| + | option mode 'link tx rx' | ||
| + | option default ' | ||
| + | config led ' | ||
| + | option trigger ' | ||
| + | option name ' | ||
| + | option sysfs ' | ||
| + | option port_mask ' | ||
| + | option default ' | ||
| + | config led ' | ||
| + | option name ' | ||
| + | option sysfs ' | ||
| + | option trigger ' | ||
| + | option port_mask ' | ||
| + | option default ' | ||
| + | config led ' | ||
| + | option name ' | ||
| + | option trigger ' | ||
| + | option sysfs ' | ||
| + | option port_mask ' | ||
| + | option default ' | ||
| + | config led ' | ||
| + | option name ' | ||
| + | option sysfs ' | ||
| + | option trigger ' | ||
| + | option port_mask ' | ||
| + | option default ' | ||
| + | config led ' | ||
| + | option sysfs ' | ||
| + | option name ' | ||
| + | option trigger ' | ||
| + | option default ' | ||
| + | |||
| + | There is a red LED on port 5, which seems to be some indication of PoE (same voltage as input [[https:// | ||
| + | |||
| + | # Disable PoE on port 5 | ||
| + | config gpio_switch ' | ||
| + | | ||
| + | | ||
| + | | ||
| + | |||
| + | Or temporarily with the following command (PoE will continue supplying power over port 5, even without the red LED on **[However, see Note below]** ) . You can put it in / | ||
| + | |||
| + | echo 0 > / | ||
| + | ** Note 2018-10-10 ** | ||
| + | Using OpenWRT 18.06.1, after the above command is issued the red LED turns off //and// PoE power is turned off. | ||
| + | |||
| + | === Built in ethernet switch === | ||
| + | |||
| + | In / | ||
| + | |||
| + | config switch ' | ||
| + | option enable ' | ||
| + | | ||
| + | |||
| + | ==== Example VLAN configuration for switch ports ==== | ||
| + | |||
| + | In / | ||
| + | |||
| + | config switch ' | ||
| + | option enable ' | ||
| + | option enable_vlan ' | ||
| + | config switch_vlan | ||
| + | option device ' | ||
| + | option vlan ' | ||
| + | option vid ' | ||
| + | option ports '0t 1 2' | ||
| + | config switch_vlan | ||
| + | option device ' | ||
| + | option vlan ' | ||
| + | option vid ' | ||
| + | option ports '0t 3 4' | ||
| + | | ||
| + | |||
| + | ===== References ===== | ||
| + | |||
| + | Helpfull info: | ||
| + | |||
| + | * [[http:// | ||
| + | * [[http:// | ||
| + | * [[http:// | ||
| + | * [[http:// | ||
| + | |||
| + | patchworks.openwrt.org is not working since ~2015, the following URL will not work anymore, but you may be interested in URLs pointing to it for the history of dev. on this routerboard. | ||
| + | |||
| + | http:// | ||
| + | |||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||