MikroTik RB5009UG+S+IN

The MikroTik RB5009UG+S+IN is a compact multigig router based on Marvell's Armada 7040 ARM64 SoC. It comes with an SFP+ port, one 2.5 GbE port (with PoE+ in) and 7 GbE ports. It can be wall mounted or rack mounted with the MikroTik K-79 rackmount kit.

RB5009UG+S+IN

None at this time.

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
RB5009UG+S+INMarvell Armada 704014001024NAND, 161024----7-1x 3.0

Install OpenWrt (generic explanation)

WARNING:

Please read the Common Procedures for MikroTik RouterBoard Products before attempting to replace the bootloader and flash OpenWrt onto your device.

The instructions lean heavily on the external binaries and instructions adron-s kindly provides on his RB5009UG+S+IN GitHub page. You will need the following binaries:

Although support is mature (only 2,5 GbE PHY is not fully functional), support won't get merged as long as external binaries (the hacked RouterBOOT) are needed to introduce OpenWrt support.

A few things to note:

  • You can use your own sysupgrade image. The patch set adding RB5009UG support to OpenWrt should still apply rather cleanly to 22.03 HEAD and master as of writing (May 2022), but it's recommended to stick to the provided (and known working) initramfs image for the installation procedure.
  • Even though the modified RouterBOOT re-enables serial access, one still needs to solder wires or connectors to actually use it.

Patch sets:

  • 22.03 (last updated 2022-06-13)
  • master (last updated 2022-06-26)
  • Pull the power plug from the RB5009UG.
  • Set up dnsmasq as documented in the common MikroTik instructions and make it serve openwrt-mvebu-cortexa72-mikrotik_rb5009-initramfs-fit-uImage.elf. Make sure to use the default MikroTik subnet - 192.168.88.x and verify your firewall allows traffic on it.
  • Plug the cable into port 1 (so the 2,5 GbE port), keep the RESET button pressed, power up the router.
  • You'll see the green LED at the bottom right of the SFP+ port light up at some point and then blink. As soon as the light goes out (about 20 seconds after powering up the router), let go of the RESET button.
  • After a few seconds you should see the image getting loaded by the router with the following message:
  dnsmasq-tftp: sent /srv/tftp/openwrt-mvebu-cortexa72-mikrotik_rb5009-initramfs-fit-uImage.elf to 192.168.88.163
  • Unplug the network cable from the router, and stop dnsmasq on your computer.
  • Plug the network cable into one of the 'LAN' ports (2-8), and have some patience until OpenWrt is booted. If you set your computer to acquire an address by DHCP, that helps (it won't work until OpenWrt is fully booted).

Once you are logged into OpenWrt you can follow the instructions lined out in adron-s's README:

  • Replace the RouterBOOT binary
  wget https://github.com/adron-s/aux-loader2/raw/main/releases/2.xx-latest/rbt-with-aux-for-mtd5.bin -O- | mtd write - RouterBOOT
  • Set RouterBOOT to boot from the NOR flash
  echo cfg > /sys/firmware/mikrotik/soft_config/boot_device
  echo 1 > /sys/firmware/mikrotik/soft_config/commit

Only after that you can flash the sysupgrade image:

  # sysupgrade -n /tmp/openwrt-mvebu-cortexa72-mikrotik_rb5009-squashfs-sysupgrade.bin

The RB5009UG has both a 16 MiB NOR flash chip and a 1 GiB NAND one. For now the NOR is used to store the OpenWrt kernel; rootfs and rootfs_data are stored on the NAND. The UBI device is registered as mtd0, so counting on the NOR chip starts from mtd1.

MikroTik RB5009UG+S+IN NOR Flash Layout
Layer0 raw NOR flash memory chip (w25q128jv spi0.0: w25q128jv) 16384 KiB
Layer1 mtd9 first_1M 1024 KiB mtd8 kernel 15360 KiB
Layer2 mtd1 ATF 599 KiB mtd2 backup_RouterBOOT 101 KiB mtd3 hard_config 4 KiB mtd4 RouterBOOT 64 KiB mtd5 soft_config 64 KiB mtd6 DTS 64 KiB mtd7 free_space 128 KiB

FIXME The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

  • How you install OpenWrt from a device freshly opened
  • The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

  • Browse to http://192.168.1.1/Upgrade.asp
  • Upload .bin file to router
  • Wait for it to reboot
  • Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

Specific values needed for tftp

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Follow the MikroTik netboot procedure documented on the wiki. You need to the hacked RouterBOOT binary to be able to boot OpenWrt (see instructions by adron-s).

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Below configuration is as configured on OpenWrt; there is no dedicated WAN port, all available ports are connected to the Marvell switch. One can set any port as WAN (e.g. p8).

The default network configuration is:

Interface Name Description Default configuration
br-lan Ethernet 2-8 & SFP + 192.168.1.1/24
p1 2,5 GbE configured as WAN port DHCP (default)

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) EXAMPLE 4
LAN 1 EXAMPLE 3
LAN 2 EXAMPLE 2
LAN 3 EXAMPLE 1
LAN 4 EXAMPLE 0

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The MikroTik RB5009UG+S+IN has the following buttons:

BUTTON Event
EXAMPLE Reset reset
EXAMPLE Secure Easy Setup ses
EXAMPLE No buttons at all. -

FIXME

  1. This table is automatically generated, once the correct filters for Brand and Model are set.
  2. If you see “Nothing.” instead of a table, please edit this section and adjust the filters with the proper Brand and Model. Just try, it's easy.
  3. If you still don't see a table here, or a table filled with '¿': Is there already a Techdata page available for MikroTik RB5009UG+S+IN ? If not: Create one.
  4. If you see a table with the desired device data, everything is OK and you can delete this text and the <WRAP> that encloses it.
  5. If it still doesn't work: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help.
Nothing.

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, …

  • To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for MikroTik RB5009UG+S+IN @@Version@@
EXAMPLE 115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

bootloader

Use adron-s's hacked RouterBOOT (see installation section) to boot OpenWrt images. The default RouterBOOT only supports MikroTik's own images.

None so far.

COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE


[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd081] [ 0.000000] Linux version 5.10.118 (5800x@crunchbot) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19160+20-7ea2f3d6e2) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu May 26 10:38:36 2022 [ 0.000000] Machine model: MikroTik RB5009 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff] [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 4096 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 262144 pages, LIFO batch:63 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS resident on physical CPU 0x0 [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 16 pages/cpu s27608 r8192 d29736 u65536 [ 0.000000] pcpu-alloc: s27608 r8192 d29736 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048 [ 0.000000] Kernel command line: [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1017160K/1048576K available (7998K kernel code, 900K rwdata, 1312K rodata, 448K init, 272K bss, 31416K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f022f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:160, num:32) [ 0.000000] GICv2m: range[mem 0xf0280000-0xf0280fff], SPI[160:191] [ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:192, num:32) [ 0.000000] GICv2m: range[mem 0xf0290000-0xf0290fff], SPI[192:223] [ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:224, num:32) [ 0.000000] GICv2m: range[mem 0xf02a0000-0xf02a0fff], SPI[224:255] [ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:256, num:32) [ 0.000000] GICv2m: range[mem 0xf02b0000-0xf02b0fff], SPI[256:287] [ 0.000000] random: get_random_bytes called from 0xffffffc010920cac with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ 0.000003] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ 0.000079] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.000087] pid_max: default: 32768 minimum: 301 [ 0.000153] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.000165] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.000894] rcu: Hierarchical SRCU implementation. [ 0.000960] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.001133] smp: Bringing up secondary CPUs … [ 0.001462] Detected PIPT I-cache on CPU1 [ 0.001501] CPU1: Booted secondary processor 0x0000000001 [0x410fd081] [ 0.001854] Detected PIPT I-cache on CPU2 [ 0.001885] CPU2: Booted secondary processor 0x0000000100 [0x410fd081] [ 0.002245] Detected PIPT I-cache on CPU3 [ 0.002266] CPU3: Booted secondary processor 0x0000000101 [0x410fd081] [ 0.002310] smp: Brought up 1 node, 4 CPUs [ 0.002322] SMP: Total of 4 processors activated. [ 0.002327] CPU features: detected: 32-bit EL0 Support [ 0.002332] CPU features: detected: CRC32 instructions [ 0.002367] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.002372] CPU: All CPU(s) started at EL2 [ 0.002388] alternatives: patching kernel code [ 0.004432] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.004444] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.004523] pinctrl core: initialized pinctrl subsystem [ 0.004835] NET: Registered protocol family 16 [ 0.005281] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.005318] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.005353] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.005556] thermal_sys: Registered thermal governor 'step_wise' [ 0.006000] cpuidle: using governor ladder [ 0.006024] ASID allocator initialised with 65536 entries [ 0.015545] cryptd: max_cpu_qlen set to 1000 [ 0.016691] SCSI subsystem initialized [ 0.016806] libata version 3.00 loaded. [ 0.016898] usbcore: registered new interface driver usbfs [ 0.016920] usbcore: registered new interface driver hub [ 0.016943] usbcore: registered new device driver usb [ 0.017539] clocksource: Switched to clocksource arch_sys_counter [ 0.017858] NET: Registered protocol family 2 [ 0.017995] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.018411] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.018426] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.018468] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.018554] TCP: Hash tables configured (established 8192 bind 8192) [ 0.018653] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.018672] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.018743] NET: Registered protocol family 1 [ 0.018760] PCI: CLS 0 bytes, default 64 [ 0.020798] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.022530] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.022536] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.026214] armada-ap806-pinctrl f06f4000.system-controller:pinctrl: registered pinctrl driver [ 0.026613] armada-cp110-pinctrl f2440000.system-controller:pinctrl: registered pinctrl driver [ 0.027305] gpio-87 (enable USB power): hogged as output/high [ 0.027320] gpio-91 (enable LED-s power): hogged as output/high [ 0.029065] mv_xor_v2 f0400000.xor: Marvell Version 2 XOR driver [ 0.029588] mv_xor_v2 f0420000.xor: Marvell Version 2 XOR driver [ 0.030103] mv_xor_v2 f0440000.xor: Marvell Version 2 XOR driver [ 0.030612] mv_xor_v2 f0460000.xor: Marvell Version 2 XOR driver [ 0.031172] mv_xor_v2 f26a0000.xor: Marvell Version 2 XOR driver [ 0.031692] mv_xor_v2 f26c0000.xor: Marvell Version 2 XOR driver [ 0.031833] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.032257] printk: console [ttyS0] disabled [ 0.052418] f0512000.serial: ttyS0 at MMIO 0xf0512000 (irq = 17, base_baud = 12500000) is a 16550A [ 0.721676] printk: console [ttyS0] enabled [ 0.726477] omap_rng f2760000.trng: Random Number Generator ver. 203b34c [ 0.726793] random: fast init done [ 0.736652] random: crng init done [ 0.741651] loop: module loaded [ 0.746024] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xd3 [ 0.752417] nand: Macronix MX60LF8G18AC [ 0.756269] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.764465] Bad block table found at page 524224, version 0x01 [ 0.771201] Bad block table found at page 524160, version 0x01 [ 0.777494] nand_read_bbt: bad block at 0x000002a60000 [ 0.782668] nand_read_bbt: bad block at 0x000019b80000 [ 0.787835] nand_read_bbt: bad block at 0x000024ea0000 [ 0.792997] nand_read_bbt: bad block at 0x00002aac0000 [ 0.798301] 1 fixed-partitions partitions found on MTD device f2720000.nand [ 0.805291] Creating 1 MTD partitions on “f2720000.nand”: [ 0.810722] 0x000000000000-0x000040000000 : “ubi” [ 0.818604] spi-nor spi0.0: w25q128jv (16384 Kbytes) [ 0.823704] 9 fixed-partitions partitions found on MTD device spi0.0 [ 0.830091] Creating 9 MTD partitions on “spi0.0”: [ 0.834902] 0x000000000000-0x000000095c04 : “ATF” [ 0.839805] 0x000000095c04-0x0000000af000 : “backup_RouterBOOT” [ 0.845886] 0x0000000af000-0x0000000b0000 : “hard_config” [ 0.851463] 0x0000000b0000-0x0000000c0000 : “RouterBOOT” [ 0.856932] 0x0000000c0000-0x0000000d0000 : “soft_config” [ 0.862493] 0x0000000d0000-0x0000000e0000 : “DTS” [ 0.867363] 0x0000000e0000-0x000000100000 : “free_space” [ 0.872856] 0x000000100000-0x000001000000 : “kernel” [ 0.877988] 0x000000000000-0x000000100000 : “first_1M” [ 0.886748] mv88e6085 f212a200.mdio-mii:00: switch 0x3930 detected: Marvell 88E6393X, revision 0 [ 0.908910] hwmon hwmon0: temp1_input not attached to any thermal zone [ 0.948090] hwmon hwmon1: temp1_input not attached to any thermal zone [ 0.987354] hwmon hwmon2: temp1_input not attached to any thermal zone [ 1.025814] hwmon hwmon3: temp1_input not attached to any thermal zone [ 1.065077] hwmon hwmon4: temp1_input not attached to any thermal zone [ 1.103552] hwmon hwmon5: temp1_input not attached to any thermal zone [ 1.143531] hwmon hwmon6: temp1_input not attached to any thermal zone [ 1.199104] mvpp2 f2000000.ethernet: using 8 per-cpu buffers [ 1.219281] mvpp2 f2000000.ethernet eth0: Using dtb mac address dc:2c:6e:45:cf:71 [ 1.237252] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.243826] ehci-pci: EHCI PCI platform driver [ 1.248320] ehci-platform: EHCI generic platform driver [ 1.253651] ehci-orion: EHCI orion driver [ 1.257966] xhci-hcd f2510000.usb3: xHCI Host Controller [ 1.263310] xhci-hcd f2510000.usb3: new USB bus registered, assigned bus number 1 [ 1.270897] xhci-hcd f2510000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 1.280189] xhci-hcd f2510000.usb3: irq 40, io mem 0xf2510000 [ 1.286340] hub 1-0:1.0: USB hub found [ 1.290131] hub 1-0:1.0: 1 port detected [ 1.294169] xhci-hcd f2510000.usb3: xHCI Host Controller [ 1.299547] xhci-hcd f2510000.usb3: new USB bus registered, assigned bus number 2 [ 1.307065] xhci-hcd f2510000.usb3: Host supports USB 3.0 SuperSpeed [ 1.313475] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.321774] hub 2-0:1.0: USB hub found [ 1.325551] hub 2-0:1.0: 1 port detected [ 1.329729] usbcore: registered new interface driver usb-storage [ 1.335997] armada38x-rtc f2284000.rtc: registered as rtc0 [ 1.341530] armada38x-rtc f2284000.rtc: setting system clock to 2022-05-29T17:51:51 UTC (1653846711) [ 1.350757] i2c /dev entries driver [ 1.367905] sbsa-gwdt f0610000.watchdog: Initialized with 10s timeout @ 25000000 Hz, action=0. [enabled] [ 1.378118] sdhci: Secure Digital Host Controller Interface driver [ 1.384330] sdhci: Copyright© Pierre Ossman [ 1.388928] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.409499] MikroTik RouterBOARD hardware configuration sysfs driver v0.07 [ 1.429700] MikroTik RouterBOARD software configuration sysfs driver v0.05 [ 1.437479] NET: Registered protocol family 10 [ 1.442844] Segment Routing with IPv6 [ 1.446553] NET: Registered protocol family 17 [ 1.451158] 8021q: 802.1Q VLAN Support v1.8 [ 1.458282] mv88e6085 f212a200.mdio-mii:00: switch 0x3930 detected: Marvell 88E6393X, revision 0 [ 1.483854] hwmon hwmon0: temp1_input not attached to any thermal zone [ 1.520856] hwmon hwmon1: temp1_input not attached to any thermal zone [ 1.560104] hwmon hwmon2: temp1_input not attached to any thermal zone [ 1.598619] hwmon hwmon3: temp1_input not attached to any thermal zone [ 1.636638] hwmon hwmon4: temp1_input not attached to any thermal zone [ 1.674213] hwmon hwmon5: temp1_input not attached to any thermal zone [ 1.713125] hwmon hwmon6: temp1_input not attached to any thermal zone [ 2.286862] mvpp2 f2000000.ethernet: all ports have a low MTU, switching to per-cpu buffers [ 2.345512] mvpp2 f2000000.ethernet: using 8 per-cpu buffers [ 2.459415] mv88e6085 f212a200.mdio-mii:00 p8 (uninitialized): PHY [!cp0!config-space@f2000000!mdio@12a200!switch@0!mdio:01] driver [Marvell 88E6393 Family] (irq=55) [ 2.579416] mv88e6085 f212a200.mdio-mii:00 p7 (uninitialized): PHY [!cp0!config-space@f2000000!mdio@12a200!switch@0!mdio:02] driver [Marvell 88E6393 Family] (irq=56) [ 2.699396] mv88e6085 f212a200.mdio-mii:00 p6 (uninitialized): PHY [!cp0!config-space@f2000000!mdio@12a200!switch@0!mdio:03] driver [Marvell 88E6393 Family] (irq=57) [ 2.819393] mv88e6085 f212a200.mdio-mii:00 p5 (uninitialized): PHY [!cp0!config-space@f2000000!mdio@12a200!switch@0!mdio:04] driver [Marvell 88E6393 Family] (irq=58) [ 2.939393] mv88e6085 f212a200.mdio-mii:00 p4 (uninitialized): PHY [!cp0!config-space@f2000000!mdio@12a200!switch@0!mdio:05] driver [Marvell 88E6393 Family] (irq=59) [ 3.059411] mv88e6085 f212a200.mdio-mii:00 p3 (uninitialized): PHY [!cp0!config-space@f2000000!mdio@12a200!switch@0!mdio:06] driver [Marvell 88E6393 Family] (irq=60) [ 3.179397] mv88e6085 f212a200.mdio-mii:00 p2 (uninitialized): PHY [!cp0!config-space@f2000000!mdio@12a200!switch@0!mdio:07] driver [Marvell 88E6393 Family] (irq=61) [ 3.486023] mv88e6085 f212a200.mdio-mii:00 p1 (uninitialized): PHY [!cp0!config-space@f2000000!mdio@12a200!switch@0!mdio1:00] driver [Qualcomm QCA8081] (irq=POLL) [ 3.502789] DSA: tree 0 setup [ 3.507205] UBI: auto-attach mtd0 [ 3.510568] ubi0: attaching mtd0 [ 10.950134] ubi0: scanning is finished [ 10.967781] ubi0: attached mtd0 (name “ubi”, size 1024 MiB) [ 10.973382] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 10.980295] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 10.987111] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 10.994106] ubi0: good PEBs: 8180, bad PEBs: 12, corrupted PEBs: 0 [ 11.000320] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 11.007578] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 507293880 [ 11.016662] ubi0: available PEBs: 0, total reserved PEBs: 8180, PEBs reserved for bad PEB handling: 148 [ 11.026108] ubi0: background thread “ubi_bgt0d” started, PID 915 [ 11.026874] block ubiblock0_0: created from ubi0:0(rootfs) [ 11.037669] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 11.048723] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 11.056090] Freeing unused kernel memory: 448K [ 11.117723] Run /sbin/init as init process [ 11.121848] with arguments: [ 11.121857] /sbin/init [ 11.121864] with environment: [ 11.121872] HOME=/ [ 11.121879] TERM=linux [ 11.388337] init: Console is alive [ 11.391839] init: - watchdog - [ 11.650055] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 11.710786] ehci-fsl: Freescale EHCI Host controller driver [ 11.716947] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 11.728281] init: - preinit - [ 12.275546] mvpp2 f2000000.ethernet eth0: configuring for inband/10gbase-r link mode [ 12.284810] mv88e6085 f212a200.mdio-mii:00 p2: configuring for phy/ link mode [ 12.295174] 8021q: adding VLAN 0 to HW filter on device p2 [ 12.331417] mvpp2 f2000000.ethernet eth0: Link is Up - 10Gbps/Full - flow control off [ 12.340711] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 15.262078] mv88e6085 f212a200.mdio-mii:00 p2: Link is Up - 1Gbps/Full - flow control rx/tx [ 15.270529] IPv6: ADDRCONF(NETDEV_CHANGE): p2: link becomes ready [ 16.449537] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 16.455347] UBIFS (ubi0:1): background thread “ubifs_bgt0_1” started, PID 1006 [ 16.512595] UBIFS (ubi0:1): recovery needed [ 16.650329] UBIFS (ubi0:1): recovery completed [ 16.654841] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name “rootfs_data” [ 16.662716] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 16.672681] UBIFS (ubi0:1): FS size: 1010094080 bytes (963 MiB, 7955 LEBs), journal size 33521664 bytes (31 MiB, 264 LEBs) [ 16.683775] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 16.690423] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 7A2EA4F9-3FB1-4552-8605-2D4FADC1BB0E, small LPT model [ 16.706870] mount_root: switching to ubifs overlay [ 16.717470] overlayfs: “xino” feature enabled using 2 upper inode bits. [ 16.737155] urandom-seed: Seeding with /etc/urandom.seed [ 16.864878] mv88e6085 f212a200.mdio-mii:00 p2: Link is Down [ 16.877294] procd: - early - [ 16.880348] procd: - watchdog - [ 17.434980] procd: - watchdog - [ 17.440867] procd: - ubus - [ 17.503437] procd: - init - [ 17.780246] urngd: v1.0.2 started. [ 17.799280] kmodloader: loading kernel modules from /etc/modules.d/* [ 17.875416] i2c-gpio sfp-i2c: using lines 32 (SDA) and 33 (SCL) [ 17.881792] sfp sfp: Host maximum power 1.0W [ 17.912207] xt_time: kernel timezone is -0000 [ 17.928207] PPP generic driver version 2.4.2 [ 17.933269] NET: Registered protocol family 24 [ 17.938908] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 17.946773] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved. [ 17.961213] kmodloader: done loading kernel modules from /etc/modules.d/* [ 21.103050] mvpp2 f2000000.ethernet eth0: Link is Down [ 21.120545] mvpp2 f2000000.ethernet eth0: configuring for inband/10gbase-r link mode [ 21.159931] mv88e6085 f212a200.mdio-mii:00 p1: configuring for inband/sgmii link mode [ 21.212404] mvpp2 f2000000.ethernet eth0: Link is Up - 10Gbps/Full - flow control off [ 21.249251] 8021q: adding VLAN 0 to HW filter on device p1 [ 21.273560] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 21.341983] br-lan: port 1(p1) entered blocking state [ 21.347095] br-lan: port 1(p1) entered disabled state [ 21.371425] device p1 entered promiscuous mode [ 21.375894] device eth0 entered promiscuous mode [ 21.464799] mv88e6085 f212a200.mdio-mii:00 p2: configuring for phy/ link mode [ 21.476985] 8021q: adding VLAN 0 to HW filter on device p2 [ 21.482842] br-lan: port 2(p2) entered blocking state [ 21.488025] br-lan: port 2(p2) entered disabled state [ 21.493670] device p2 entered promiscuous mode [ 21.513320] mv88e6085 f212a200.mdio-mii:00 p3: configuring for phy/ link mode [ 21.527931] 8021q: adding VLAN 0 to HW filter on device p3 [ 21.624039] br-lan: port 3(p3) entered blocking state [ 21.629145] br-lan: port 3(p3) entered disabled state [ 21.648003] device p3 entered promiscuous mode [ 21.660187] mv88e6085 f212a200.mdio-mii:00 p4: configuring for phy/ link mode [ 21.670085] 8021q: adding VLAN 0 to HW filter on device p4 [ 21.737758] br-lan: port 4(p4) entered blocking state [ 21.742854] br-lan: port 4(p4) entered disabled state [ 21.749307] device p4 entered promiscuous mode [ 21.772049] mv88e6085 f212a200.mdio-mii:00 p5: configuring for phy/ link mode [ 21.781947] 8021q: adding VLAN 0 to HW filter on device p5 [ 21.837756] br-lan: port 5(p5) entered blocking state [ 21.842850] br-lan: port 5(p5) entered disabled state [ 21.849204] device p5 entered promiscuous mode [ 21.871689] mv88e6085 f212a200.mdio-mii:00 p6: configuring for phy/ link mode [ 21.881363] 8021q: adding VLAN 0 to HW filter on device p6 [ 21.937769] br-lan: port 6(p6) entered blocking state [ 21.942862] br-lan: port 6(p6) entered disabled state [ 21.949308] device p6 entered promiscuous mode [ 21.971964] mv88e6085 f212a200.mdio-mii:00 p7: configuring for phy/ link mode [ 21.981833] 8021q: adding VLAN 0 to HW filter on device p7 [ 22.034163] br-lan: port 7(p7) entered blocking state [ 22.039278] br-lan: port 7(p7) entered disabled state [ 22.045773] device p7 entered promiscuous mode [ 22.104722] mv88e6085 f212a200.mdio-mii:00 sfp: configuring for inband/10gbase-r link mode [ 22.236017] 8021q: adding VLAN 0 to HW filter on device sfp [ 22.246689] br-lan: port 8(sfp) entered blocking state [ 22.251972] br-lan: port 8(sfp) entered disabled state [ 22.258657] device sfp entered promiscuous mode [ 22.284734] mv88e6085 f212a200.mdio-mii:00 p8: configuring for phy/ link mode [ 22.294658] 8021q: adding VLAN 0 to HW filter on device p8 [ 24.652106] mv88e6085 f212a200.mdio-mii:00 p2: Link is Up - 1Gbps/Full - flow control rx/tx [ 24.660581] br-lan: port 2(p2) entered blocking state [ 24.665676] br-lan: port 2(p2) entered forwarding state [ 24.671747] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 25.202107] mv88e6085 f212a200.mdio-mii:00 p8: Link is Up - 1Gbps/Full - flow control rx/tx


Space for additional notes, links to forum threads or other resources.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2022/06/27 06:37
  • by borromini