Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:mikrotik:rb2011uias [2018/01/13 22:49] – [Installation] safe0101 | toh:mikrotik:rb2011uias [2021/02/27 18:05] – cleanup according to the fixme notes danijeltudek | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Mikrotik RouterBoard RB2011-UiAS-2HnD-IN ====== | ||
| + | The RB2011-UiAS-2HnD-IN differs from its predecessor RB2011-UAS-2HnD-IN supposedly only by supporting Mikrotik passive PoE on ETH10, but it is also identified to the OpenWrt linux kernel as a new model (2011r5 instead of 2011G) which is why it is not recognized by older OpenWrt kernels that do recognize the RB2011-UAS-2HnD-IN. The -IN refers to the indoor enclosure. The routerboard is also available without enclosure as RB2011-UiAS-2HnD. | ||
| + | |||
| + | |||
| + | ===== Supported Versions ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | ||
| + | headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data | ||
| + | align : c, | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | |||
| + | ===== Hardware Highlights ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, | ||
| + | header | ||
| + | align : c, | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | |||
| + | ===== Installation ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| + | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| + | align : c,c,c | ||
| + | filter | ||
| + | ---- | ||
| + | |||
| + | Please refer to [[toh: | ||
| + | |||
| + | |||
| + | ===== Hardware ===== | ||
| + | ==== Info ==== | ||
| + | ^ Architecture | ||
| + | ^ Vendor | ||
| + | ^ Bootloader | ||
| + | ^ System-On-Chip | ||
| + | ^ CPU Speed | 600 MHz - can be overclocked from boot monitor | ||
| + | ^ Flash size | 128 MiB NAND Flash | | ||
| + | ^ RAM | 128 MiB DDR2 | | ||
| + | ^ Wireless | ||
| + | ^ Ethernet | ||
| + | ^ | AR8227 - 5x 10/ | ||
| + | ^ USB | 1x 2.0 micro (host/ | ||
| + | ^ Serial | ||
| + | ^ JTAG | no? | | ||
| + | ^ other | 2" color touch display | ||
| + | |||
| + | FIXME [[http:// | ||
| + | |||
| + | [[https:// | ||
| + | [[http:// | ||
| + | [[http:// | ||
| + | |||
| + | | 31 | TX_INVERT - Decides whether to select the inversion of the GTX clock after the delay line | | ||
| + | | 30 | GIGE_QUAD - Decides whether to allow a 2 ns shift (clock in the middle of a data transfer) to the GTX clock. This bit is only effective when bit 25 is set | | ||
| + | | 29:28 | RX_DELAY - The delay buffers in the Rx clock path to adjust against the edge/ | ||
| + | | 27:26 | TX_DELAY - Delay line for the GTX clock that goes along with the data | | ||
| + | | 25 | GIGE - Set only after a 1000 Mbps connection has been negotiated | | ||
| + | | 24 | OFFSET_PHASE - Used to select if the start is from the positive or negative phase (or whether to have a 180 degree change in addition to the phase-delay in [11:8]. | | ||
| + | |||
| + | 0x6f: 30 29 27 26 25 24 | ||
| + | 0x3e: 29 28 27 26 25 | ||
| + | |||
| + | ===== Metarouter ===== | ||
| + | |||
| + | See [[docs: | ||
| + | |||
| + | ===== See also ===== | ||
| + | |||
| + | * [[: | ||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||