Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
toh:mikrotik:rb133 [2019/05/01 07:34] – Datatables added, cleanup tmomastoh:mikrotik:rb133 [2021/10/15 09:06] – ↷ Links adapted because of a move operation bobafetthotmail
Line 32: Line 32:
   - An ethernet port and cable to download the NetBoot kernel and the NAND image.   - An ethernet port and cable to download the NetBoot kernel and the NAND image.
   - A DHCP server to tell the RB1xx where to get it's netboot image (e.g. DnsMasq).   - A DHCP server to tell the RB1xx where to get it's netboot image (e.g. DnsMasq).
-  - A TFTPD server to supply the NetBoot image to load a barebone OpenWrt RAMdisk image (e.g. DnsMasq).+  - A [[docs:guide-user:troubleshooting:tftpserver|tftpd server]] to supply the NetBoot image to load a barebone OpenWrt RAMdisk image (e.g. DnsMasq).
   - A web server to serve up the [[permanent version]] of the OpenWrt kernel and rootfs (you can use SCP as well).   - A web server to serve up the [[permanent version]] of the OpenWrt kernel and rootfs (you can use SCP as well).
  
Line 39: Line 39:
 ==== Building images ==== ==== Building images ====
  
-See [[docs:guide-developer:build-system:start|official howto]] for more info.+See [[docs:guide-developer:toolchain:start|official howto]] for more info.
  
 :!: If you select the squashfs image, it may take quite a few minutes for the device to power on. :!: If you select the squashfs image, it may take quite a few minutes for the device to power on.
Line 62: Line 62:
 then access to the serial console terminal , connect the rb133c power and press any key to blocccare the boot sequence . then access to the serial console terminal , connect the rb133c power and press any key to blocccare the boot sequence .
  
-RouterBOOT booter 2:18 RouterBoard 133C CPU frequency : 175 MHz  Memory size:  16 MB +<code> 
 +RouterBOOT booter 2.18  
 +RouterBoard 133C CPU frequency : 175 MHz   
 +Memory size:  16 MB 
 +...
 Press any key within 2 seconds to enter setup. Press any key within 2 seconds to enter setup.
 ... ...
Line 95: Line 98:
 setting up elf image... OK setting up elf image... OK
 ... ...
 +</code>
  
 ==== Writing nand ==== ==== Writing nand ====
Line 146: Line 150:
  
 ===== Hardware info ===== ===== Hardware info =====
-^ Architecture        | MIPS                                                     +^ Architecture        | MIPS                                                                  
-^ Vendor              | MikroTik, ADMtek (Infineon)                              +^ Vendor              | MikroTik, ADMtek (Infineon)                                           
-^ Bootloader          | RouterBOOT                                               +^ Bootloader          | RouterBOOT                                                            
-^ System-On-Chip      | ADM5120 (Little Endian)                                  +^ System-On-Chip      | ADM5120 (Little Endian)                                               
-^ CPU Speed           | 175 Mhz                                                  +^ CPU Speed           | 175 Mhz                                                               
-^ Flash size          | 64/128 MiB                                               +^ Flash size          | 64/128 MiB                                                            
-^ RAM                 | 32 MiB SDRAM                                             +^ RAM                 | 32 MiB SDRAM (16 MiB on RB133C)                                       
-^ Wireless            | 3x Type III miniPCI slot                                 +^ Wireless            | 3x Type III miniPCI slot (1x on RB133C)                               
-^ Ethernet            | 3 x 10/100 Base-TX Ethernet Ports (with Auto MDI/MDIX)   +^ Ethernet            | 3 x 10/100 Base-TX Ethernet Ports (with Auto MDI/MDIX) (1 on RB133C)  
-^ USB                 | no                                                       +^ USB                 | no                                                                    
-^ Serial              | yes                                                      +^ Serial              | yes                                                                   
-^ JTAG                | no?                                                      |+^ JTAG                | no?                                                                   |
  
  
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1