The LHG-HB platform is the board design based on the Qualcomm Atheros QCA9533 used in various MikroTik wireless devices with 802.11b/g/n radio, 1x 10/100 Mbps Ethernet port, 16 MB SPI NOR flash and 64 MB RAM:
and possibly also (untested):
The LHG 2 (Light Head Grid) is a compact and light 802.11b/g/n outdoor wireless device with an integrated dual polarisation 18 dBi grid antenna and one 10/100 Mbps Ethernet port for point to point links or for use as a CPE.
The SXTsq Lite2 is a compact and lightweight 802.11b/g/n outdoor wireless device with an integrated 10 dBi antenna for point-to-point links or as a CPE unit, compact, weatherproof and easy to mount.
|Brand||Model||Version||Current Release||OEM Info||Forum Search||Technical Data|
|MikroTik||LHG 2 (RBLHG2nD)||PR pending||https://mikrotik.com/product/lhg_2||RouterBOARD LHG 2nD||View/Edit data|
|MikroTik||SXTsq Lite2 (RBSXTsq2nD)||PR pending||https://mikrotik.com/product/sxtsq_lite2||SXTsq Lite2||View/Edit data|
None at this time.
|Model||Version||Current Release||Firmware OpenWrt snapshot Install||Firmware OpenWrt snapshot Upgrade||Firmware OEM Stock|
Please add the installation procedure here.
The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!
This section deals with
Note: Reset router to factory defaults if it has been previously configured.
http://192.168.1.1if LuCI is installed.
Enter values for “FILL-IN” below
|Bootloader tftp server IPv4 address||FILL-IN|
|Bootloader MAC address (special)||FILL-IN|
|Firmware tftp image|| Latest OpenWrt release (
|TFTP transfer window||FILL-IN seconds|
|TFTP window start||approximately FILL-IN seconds after power on|
|TFTP client required IP address||FILL-IN|
These are generic instructions. Update with your router's specifics.
http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/LuCI Upgrade URL
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:
Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc
sysupgrade does not support this router, use
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc mtd write /tmp/xxx.abc linux && reboot
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
The default network configuration is:
|Interface Name||Description||Default configuration|
|br-lan||LAN & WiFi||192.168.1.1/24|
Please fill in real values for this device, then remove the EXAMPLEs
Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
|Internet (WAN)||EXAMPLE 4|
|LAN 1||EXAMPLE 3|
|LAN 2||EXAMPLE 2|
|LAN 3||EXAMPLE 1|
|LAN 4||EXAMPLE 0|
The MikroTik LHG-HB platform has the following buttons:
Note: the reset button shares GPIO 16 with the disabled rssihigh LED. To avoid conflicting behaviour, only the button is registered.
The hardware.button page contains information on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
<WRAP>that encloses it.
Insert photo of front of the casing
Insert photo of back of the casing
Insert photo of backside label
Note: This will void your warranty!
Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, …
Insert photo of PCB
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port
Replace EXAMPLE by real values.
| Serial connection parameters|
for MikroTik LHG-HB platform @@Version@@
|EXAMPLE 115200, 8N1|
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
None so far.
N/A (OEM bootlog is disabled).
COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING
Space for additional notes, links to forum threads or other resources.