MikroTik RouterBOARD hAP ac² (RBD52G-5HacD2HnD-TC)

Small router with 5 gigabit ports, dual-band 802.11ac Wi-Fi, and a powerful quad-core ARM CPU.

The commercial name of the router is hAP ac² or sometimes hAP ac 2.

Generic Router

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
RBD52G-5HacD2HnD-TC ( hAP ac² )Qualcomm IPQ401871616128Qualcomm IPQ4018b/g/na/n/ac-5-1x 3.0

Early revisions seemed to ship with 256 MiB of RAM (see wikidevi). However, revisions available in 2019 only ship with 128 MiB of RAM.

The basic network interfaces of the hAP ac2 are 5 ethernet interfaces that are connected to the CPU via a switch integrated in the SoC ipq4018, plus two radio circuits, one for 2.4 GHz and one for 5 GHz. On the encasing they are designated #1 (Internet/PoE in), and #2 - #5 (LAN). Two VLAN IDs have been reserved: '1' for the LAN ports, '2' for the Internet/PoE port

Output from 'swconfig dev switch0 show'

VLAN 1:

vid: 1
ports: 0t 1 2 3 4 

VLAN 2:

vid: 2
ports: 0t 5 

Note that port 0 is the CPU, 5 the Internet/PoE port, and LAN #2 - #5 correspond to ports 4 - 1, so reverse order to what is printed on the casing. The default network and wireless configurations that are created provide for disabled wireless, Internet/PoE seeking a dhcp server, and #2 - #5 bridged and assigned 192.168.1.1. It is possible to define additional VLAN(s) and to assign LAN ports to them, taking them out of the eth0 bridge. Use other VLAN IDs than 1 and 2 as those are reserved.

Architecture ARM
Vendor Qualcomm IPQ4018
Bootloader RouterBOOT
System-On-Chip Qualcomm IPQ4018
CPU/Speed 716 MHz
Flash-Chip Winbond W25Q128JVSM
Flash size 16 MiB
RAM 128 MiB
Wireless IPQ4018 2.4GHz/5GHz 802.11bgnac
Ethernet 10/100/1000 Mbit/s QCA8075
USB 1x 3.0
Serial Yes
JTAG ?

Front board Back board

Opening the case is not easy at first, but there are videos on Youtube: https://www.youtube.com/watch?v=3vu2AOydsls

port.serial general information about the serial port, serial port cable, etc.

Instructions for soldering pins for the serial port: Connect to RX, TX and GND.

DI RX CS DO GND TX VCC GND (WP)


o DI GND CLK DO VCC CS
Serial connection parameters
for MikroTik hAP ac²
115200, 8N1

CHANGE position e030 before bytes 40 20 08 there's a 05 to change to 00 Press any key within 2 seconds to enter setup RouterBOOT-6.43.12 What do you want to configure? d - boot delay k - boot key s - serial console n - silent boot o - boot device r - reset booter configuration e - format storage w - repartition nand g - upgrade firmware i - board info p - boot protocol t - test ram memory x - exit setup your choice: i - board info Board Info: Board type: RBD52G-5HacD2HnD Serial number: B4A00A5043E7 Firmware version: 6.43.12 CPU frequency: 716 MHz Memory size: 128 MiB Storage size: 16 MiB Build time: 2019-02-08 09:19:19 eth1 MAC address: 74:4D:28:5F:D8:75 eth2 MAC address: 74:4D:28:5F:D8:76 eth3 MAC address: 74:4D:28:5F:D8:77 eth4 MAC address: 74:4D:28:5F:D8:78 eth5 MAC address: 74:4D:28:5F:D8:79 eth6 MAC address: 74:4D:28:5F:D8:7A eth7 MAC address: 74:4D:28:5F:D8:7B press any key to continue... RouterBOOT backup booter 6.43.10 RBD52G-5HacD2HnD CPU frequency: 716 MHz Memory size: 128 MiB Storage size: 16 MiB


[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.110 (noyb@noyb) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16450-d92a9c97bf)) #0 SMP Tue Apr 13 08:29:25 2021 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: MikroTik hAP ac2 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 284 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32256 pages, LIFO batch:7 [ 0.000000] HighMem zone: 512 pages, LIFO batch:0 [ 0.000000] percpu: Embedded 15 pages/cpu s30092 r8192 d23156 u61440 [ 0.000000] pcpu-alloc: s30092 r8192 d23156 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32484 [ 0.000000] Kernel command line: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 117796K/131072K available (5613K kernel code, 186K rwdata, 1480K rodata, 1024K init, 231K bss, 13276K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x2f0/0x49c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000025] Switching to timer-based delay loop, resolution 20ns [ 0.000240] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000258] pid_max: default: 32768 minimum: 301 [ 0.000476] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000493] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001621] CPU: Testing write buffer coherency: ok [ 0.002806] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.002959] rcu: Hierarchical SRCU implementation. [ 0.003456] smp: Bringing up secondary CPUs ... [ 0.006828] smp: Brought up 1 node, 4 CPUs [ 0.006851] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.006858] CPU: All CPU(s) started in SVC mode. [ 0.011378] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.011547] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.011576] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.011862] pinctrl core: initialized pinctrl subsystem [ 0.012999] NET: Registered protocol family 16 [ 0.013424] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.014752] cpuidle: using governor ladder [ 0.014801] cpuidle: using governor menu [ 0.019774] GPIO line 414 (enable USB power) hogged as output/high [ 0.034893] cryptd: max_cpu_qlen set to 1000 [ 0.038544] usbcore: registered new interface driver usbfs [ 0.038616] usbcore: registered new interface driver hub [ 0.038674] usbcore: registered new device driver usb [ 0.038723] pps_core: LinuxPPS API ver. 1 registered [ 0.038732] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.038760] PTP clock support registered [ 0.039476] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.040731] clocksource: Switched to clocksource arch_sys_counter [ 0.041568] thermal_sys: Registered thermal governor 'step_wise' [ 0.041875] NET: Registered protocol family 2 [ 0.042595] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.042644] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.042677] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.042707] TCP: Hash tables configured (established 1024 bind 1024) [ 0.042850] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.042895] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.043181] NET: Registered protocol family 1 [ 0.043225] PCI: CLS 0 bytes, default 64 [ 0.045380] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.051414] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.051433] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.101215] bounce: pool size: 64 pages [ 0.104285] bam-dma-engine 8e04000.dma: num-channels unspecified in dt [ 0.104307] bam-dma-engine 8e04000.dma: num-ees unspecified in dt [ 0.105018] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.105109] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.105195] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.105278] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.105604] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.106235] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.106281] msm_serial 78af000.serial: uartclk = 1843200 [ 0.106335] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM [ 0.106364] msm_serial: console setup on port #0 [ 0.594243] printk: console [ttyMSM0] enabled [ 0.599139] msm_serial: driver initialized [ 0.608738] loop: module loaded [ 0.609862] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 0.618000] random: fast init done [ 0.621633] spi-nor spi0.0: w25q128jv (16384 Kbytes) [ 0.621695] 3 fixed-partitions partitions found on MTD device spi0.0 [ 0.626319] Creating 3 MTD partitions on "spi0.0": [ 0.632683] 0x000000000000-0x000000080000 : "Qualcomm" [ 0.638255] 0x000000080000-0x000000100000 : "RouterBoot" [ 0.648383] 3 routerbootpart partitions found on MTD device RouterBoot [ 0.648416] Creating 3 MTD partitions on "RouterBoot": [ 0.654233] 0x00000000e000-0x00000000f000 : "hard_config" [ 0.660203] 0x000000010000-0x000000017bbc : "dtb_config" [ 0.665714] 0x00000003d000-0x00000003e000 : "soft_config" [ 0.671080] 0x000000100000-0x000001000000 : "firmware" [ 0.680354] 2 minor-fw partitions found on MTD device firmware [ 0.680485] Creating 2 MTD partitions on "firmware": [ 0.686364] 0x000000000000-0x0000002d0000 : "kernel" [ 0.692331] 0x0000002d0000-0x000000f00000 : "rootfs" [ 0.697129] mtd: device 7 (rootfs) set to be root filesystem [ 0.701589] 1 squashfs-split partitions found on MTD device rootfs [ 0.706966] 0x0000007d0000-0x000000f00000 : "rootfs_data" [ 0.714678] libphy: ipq4019_mdio: probed [ 0.743807] ESS reset ok! [ 0.767933] ESS reset ok! [ 1.189609] libphy: Fixed MDIO Bus: probed [ 1.195522] EDMA using MAC@ - using [ 1.195536] b6:44:49:59:ef:48 [ 1.198762] EDMA using MAC@ - using [ 1.198772] 26:f9:db:ae:bd:05 [ 1.305417] i2c /dev entries driver [ 1.307495] sdhci: Secure Digital Host Controller Interface driver [ 1.307716] sdhci: Copyright(c) Pierre Ossman [ 1.314056] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.322781] MikroTik RouterBOARD hardware configuration sysfs driver v0.06 [ 1.325272] MikroTik RouterBOARD software configuration sysfs driver v0.03 [ 1.332029] NET: Registered protocol family 10 [ 1.339228] Segment Routing with IPv6 [ 1.342249] NET: Registered protocol family 17 [ 1.345894] 8021q: 802.1Q VLAN Support v1.8 [ 1.350201] Registering SWP/SWPB emulation handler [ 1.365516] hctosys: unable to open rtc device (rtc0) [ 1.371414] VFS: Mounted root (squashfs filesystem) readonly on device 31:7. [ 1.373117] Freeing unused kernel memory: 1024K [ 1.434415] Run /sbin/init as init process [ 2.059147] init: Console is alive [ 2.059420] init: - watchdog - [ 3.233910] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.384467] SCSI subsystem initialized [ 3.389174] dwc3-qcom 8af8800.usb3: IRQ hs_phy_irq not found [ 3.389219] dwc3-qcom 8af8800.usb3: IRQ dp_hs_phy_irq not found [ 3.394012] dwc3-qcom 8af8800.usb3: IRQ dm_hs_phy_irq not found [ 3.399557] dwc3-qcom 8af8800.usb3: IRQ ss_phy_irq not found [ 3.408425] dwc3 8a00000.dwc3: Failed to get clk 'ref': -2 [ 3.509098] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.509188] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.513969] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000000002010010 [ 3.521232] xhci-hcd xhci-hcd.0.auto: irq 94, io mem 0x08a00000 [ 3.531627] hub 1-0:1.0: USB hub found [ 3.536375] hub 1-0:1.0: 1 port detected [ 3.540499] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.544286] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.549533] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.558591] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.564277] hub 2-0:1.0: USB hub found [ 3.572037] hub 2-0:1.0: 1 port detected [ 3.579725] usbcore: registered new interface driver usb-storage [ 3.579987] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.594928] init: - preinit - [ 4.497800] random: jshn: uninitialized urandom read (4 bytes read) [ 4.542580] random: jshn: uninitialized urandom read (4 bytes read) [ 4.674452] random: jshn: uninitialized urandom read (4 bytes read) [ 5.418472] random: crng init done [ 5.418509] random: 4 urandom warning(s) missed due to ratelimiting [ 5.473186] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9.883875] jffs2: notice: (203) jffs2_build_xattr_subsystem: complete building xattr subsystem, 13 of xdatum (6 unchecked, 7 orphan) and 14 of xref (7 dead, 0 orphan) found. [ 9.894617] mount_root: switching to jffs2 overlay [ 9.917027] overlayfs: upper fs does not support tmpfile. [ 9.935337] urandom-seed: Seeding with /etc/urandom.seed [ 10.044424] procd: - early - [ 10.044577] procd: - watchdog - [ 10.644436] procd: - watchdog - [ 10.877991] procd: - ubus - [ 10.930851] procd: - init - [ 11.504938] kmodloader: loading kernel modules from /etc/modules.d/* [ 11.528809] Mirror/redirect action on [ 11.538352] u32 classifier [ 11.538385] input device check on [ 11.539956] Actions configured [ 11.550514] urngd: v1.0.2 started. [ 11.552468] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf [ 11.552825] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2 [ 11.574957] usbcore: registered new interface driver ums-alauda [ 11.576060] usbcore: registered new interface driver ums-cypress [ 11.580876] usbcore: registered new interface driver ums-datafab [ 11.587029] usbcore: registered new interface driver ums-freecom [ 11.593178] usbcore: registered new interface driver ums-isd200 [ 11.599039] usbcore: registered new interface driver ums-jumpshot [ 11.604678] usbcore: registered new interface driver ums-karma [ 11.611927] usbcore: registered new interface driver ums-sddr09 [ 11.618686] usbcore: registered new interface driver ums-sddr55 [ 11.624455] usbcore: registered new interface driver ums-usbat [ 11.657212] xt_time: kernel timezone is -0000 [ 13.041864] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 13.041915] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 13.053537] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 13.171243] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16 crc32 9dc2a394 [ 14.459226] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 14.459276] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 14.495695] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 14.496644] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 14.621607] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 14.735204] ath: EEPROM regdomain sanitized [ 14.735306] ath: EEPROM regdomain: 0x64 [ 14.735360] ath: EEPROM indicates we should expect a direct regpair map [ 14.735500] ath: Country alpha2 being used: 00 [ 14.735554] ath: Regpair used: 0x64 [ 15.811879] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 15.811931] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 15.823664] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 15.875930] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17 crc32 9dc2a394 [ 17.163951] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 17.164001] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 17.199834] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 17.200803] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 17.324852] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 17.437109] ath: EEPROM regdomain sanitized [ 17.437206] ath: EEPROM regdomain: 0x64 [ 17.437261] ath: EEPROM indicates we should expect a direct regpair map [ 17.437403] ath: Country alpha2 being used: 00 [ 17.437457] ath: Regpair used: 0x64 [ 17.475074] kmodloader: done loading kernel modules from /etc/modules.d/* [ 22.083860] ess_edma c080000.edma eth1: Link is Down [ 22.092651] br-lan: port 1(eth1) entered blocking state [ 22.092696] br-lan: port 1(eth1) entered disabled state [ 22.097146] device eth1 entered promiscuous mode [ 22.114966] br-lan: port 2(eth0) entered blocking state [ 22.115003] br-lan: port 2(eth0) entered disabled state [ 22.119413] device eth0 entered promiscuous mode [ 22.736344] ath: EEPROM regdomain: 0x8348 [ 22.736358] ath: EEPROM indicates we should expect a country code [ 22.736373] ath: doing EEPROM country->regdmn map search [ 22.736383] ath: country maps to regdmn code: 0x3a [ 22.736390] ath: Country alpha2 being used: US [ 22.736396] ath: Regpair used: 0x3a [ 22.736407] ath: regdomain 0x8348 dynamically updated by user [ 22.736447] ath: EEPROM regdomain: 0x8348 [ 22.736453] ath: EEPROM indicates we should expect a country code [ 22.736463] ath: doing EEPROM country->regdmn map search [ 22.736472] ath: country maps to regdmn code: 0x3a [ 22.736477] ath: Country alpha2 being used: US [ 22.736483] ath: Regpair used: 0x3a [ 22.736490] ath: regdomain 0x8348 dynamically updated by user [ 23.030871] br-lan: port 2(eth0) entered blocking state [ 23.030921] br-lan: port 2(eth0) entered forwarding state [ 23.036551] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 24.621071] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 24.621119] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 24.656585] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 24.657947] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 24.944662] ath10k_ahb a000000.wifi: rts threshold -1 [ 24.945845] ath10k_ahb a000000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 24.980480] br-lan: port 3(wlan0) entered blocking state [ 24.980545] br-lan: port 3(wlan0) entered disabled state [ 24.985421] device wlan0 entered promiscuous mode [ 25.086637] ath10k_ahb a000000.wifi: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 25.306664] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 25.307330] br-lan: port 3(wlan0) entered blocking state [ 25.312333] br-lan: port 3(wlan0) entered forwarding state [ 26.829076] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 26.829128] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 26.864972] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 26.866533] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 27.150624] ath10k_ahb a800000.wifi: rts threshold -1 [ 27.152804] ath10k_ahb a800000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 27.173298] br-lan: port 4(wlan1) entered blocking state [ 27.173346] br-lan: port 4(wlan1) entered disabled state [ 27.178319] device wlan1 entered promiscuous mode [ 27.812550] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 27.814831] br-lan: port 4(wlan1) entered blocking state [ 27.818247] br-lan: port 4(wlan1) entered forwarding state [ 352.794743] ess_edma c080000.edma eth1: Link is Up - 100Mbps/Full - flow control off [ 352.795727] br-lan: port 1(eth1) entered blocking state [ 352.802296] br-lan: port 1(eth1) entered forwarding state


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/05/01 08:40
  • by zorun