Linksys WRT610N

The WRT610N v1.0 is based on the Broadcom 4705 cpu running at 300MHz. It has 8 MB flash and 64 MB SDRAM (2x HY5DU561622FTP). The WNICs are a dual BCM4322 Chipset, one for 5GHz A and N and one for 2.4GHz B,G and N. The switch is a BCM53115 chip. The WRT610N runs 802.11 A, B, G, and Draft N wireless protocols. It provides 4 gigabit LAN ports, 1 WAN port and a USB 2.0 port.

Version/Model S/N Model Specific Notes
WRT610N v0 ? same as v1
WRT610N v1.0 CTG01 b43 works with 2.4GHz radio, wl with both
WRT610N v2.0 CTG11 same hardware as Linksys E3000
  • Fixed in trunk: The switch's first ethernet port is stuck in a slow mode: https://dev.openwrt.org/ticket/13315
  • The b43 wireless driver doesn't support 11n modes (HT) or 5Ghz. The closed-source wl can be used for both.

Download trunk snapshot openwrt-wrt610n_v2-squashfs.bin or trunk snapshot openwrt-wrt610n_v1-squashfs.bin depending on your hardware version. These snapshots ship with b43, so 5GHz wireless will not work and only BG rates will be available.

Alternately, see instructions for building openwrt from source and set the following configuration (in 'make menuconfig')

Target System (Broadcom BCM47xx/53xx) --->
Target Profile (Broadcom SoC, all Ethernet, BCM43xx WiFi (wl, proprietary))  --->

From dd-wrt Linksys WRT610N documentation

  1. unplug all ethernet ports (Important!)
  2. unplug power
  3. plug power in
  4. wait 2-2.5 seconds
  5. press the reset button and keep it pressed for 5 seconds, then release it
  6. reconnect ethernet (DHCP shoud give IP address to computer)
  7. point your browser at http://192.168.1.1.
  8. You should see a “Management Firmware update” screen. Give it the openwrt-wrt610n_v1-squashfs.bin or openwrt-wrt610n_v2-squashfs.bin file depending on hardware version.

If you have a serial console and the above isn't working you can press ctrl-c while the router is booting to get to a CFE prompt, then either:

  1. nvram set safe_mode_upgrade=on
  2. nvram commit
  3. reboot

Or

  1. flash -ctheader -https : flash1.trx

FIXME even though CFE says it's doing that last bit, it appears some setup is missing. Running the command manually from a canceled boot and then browsing to the upgrade page shows an immediate “Update Success” and the router reboots (CFE reports that it has run the “reboot” command).

Upload the openwrt-wrt610n_v1-squashfs.bin or openwrt-wrt610n_v2-squashfs.bin image with TFTP.

FIXME describe actual method

Based on the CFE boot logs, it appears that the router attempts to load something via tftp with a max size of 0x32000 bytes (3.625MiB) into ram. This would limit our image size quite a bit.

If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

  • Login as root via SSH on 192.168.1.1
  • Use the following commands to upgrade.
cd /tmp/
wget http://downloads.openwrt.org/latest/brcm-2.4/openwrt-brcm-2.4-squashfs.trx
sysupgrade /tmp/openwrt-brcm-2.4-squashfs.trx
  • If sysupgrade does not support this router, use the following commands.
cd /tmp/
wget http://downloads.openwrt.org/latest/brcm-2.4/openwrt-brcm-2.4-squashfs.trx
mtd write /tmp/openwrt-brcm-2.4-squashfs.trx linux && reboot
Architecture: MIPS
Vendor: Broadcom
Bootloader: CFE
System-On-Chip: Broadcom BCM4705
CPU Speed: 300 MHz
Flash-Chip: EON EN29LV640B-90TIP - 64 Megabit (8M x 8-bit / 4M x 16-bit)
Flash size: 8 MiB
RAM: 64 MiB
Wireless: 2x Broadcom BCM4322 802.11a/b/g/n (integrated)
Ethernet: Broadcom BCM53115 Gigabit Switch
USB: 1x USB2.0 Host
Serial: Yes
JTAG: ?

For v2 see E3000

Note: This will void your warranty!

The case parts are hold together by plastic claws, use a screwdriver to release them.

See this form post for details.

PCB (front side):
Insert picture of PCB front side

PCB (back side):
wrt610n_pcb_back.jpg

There are 5 solder pads near the rim on the backside of the PCB, see image above. Serial port settings are 115000@8N1.

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
vlan0 (eth0.0) LAN ports (1 to 4) Static
vlan1 (eth0.1) WAN port DHCP
wl0 WiFi Disabled

Switch port numbers are currently unknown.

Available buttons are currently not known.

If you forgot your password, broke one of the startup scripts, firewalled yourself or corrupted the JFFS2 partition, you can get back in by using OpenWrt's failsafe mode.

  • Unplug the router's power cord.
  • Connect the router's LAN1 port directly to your PC.
  • Configure your PC with a static IP address between 192.168.1.2 and 192.168.1.254. E. g. 192.168.1.2 (gateway and DNS is not required).
  • Plug the power on and wait for the DMZ LED to light up.
  • While the DMZ LED is on immediately press any button (Reset and Secure Easy Setup will work) a few times .
  • If done right the DMZ LED will quickly flash 3 times every second.
  • You should be able to telnet to the router at 192.168.1.1 now (no username and password)

Since this part is identical for all devices, see Basic configuration.

To connect stuff to the USB port, please see Connect stuff to the USB port.

CFE version 1.0.37 for BCM947XX (32bit,SP,LE) Build Date: Mon May 12 15:37:48 CST 2008 (ljh@team2-complier) Copyright (C) 2000,2001,2002,2003 Broadcom Corporation. Initializing Arena Initializing PCI. [normal] PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02) PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02) PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02) PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02) PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02) PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02) PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02) PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02) PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02) PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02) PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02) Initializing Devices. No DPN This is a Parallel Flash Boot partition size = 262144(0x40000) Partition information: boot #00 00000000 -> 0003FFFF (262144) trx #01 00040000 -> 0004001B (28) os #02 0004001C -> 007F7FFF (8093668) nvram #03 007F8000 -> 007FFFFF (32768) Partition information: boot #00 00000000 -> 0003FFFF (262144) trx #01 00040000 -> 007F7FFF (8093696) nvram #02 007F8000 -> 007FFFFF (32768) PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004 PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000 ge0: BCM5750 Ethernet at 0x18010000 CPU type 0x2901A: 300MHz Total memory: 65536 KBytes Total memory used by CFE: 0x80700000 - 0x807A60B0 (680112) Initialized Data: 0x8073A2B0 - 0x8073E540 (17040) BSS Area: 0x8073E540 - 0x807400B0 (7024) Local Heap: 0x807400B0 - 0x807A40B0 (409600) Stack Area: 0x807A40B0 - 0x807A60B0 (8192) Text (code) segment: 0x80700000 - 0x8073A2B0 (238256) Boot area (physical): 0x007A7000 - 0x007E7000 Relocation Factor: I:00000000 - D:00000000 Boot version: v4.2 The boot is CFE mac_init(): Find mac [00:21:29:C6:61:00] in location 0 Nothing... country_init(): Find country code in location 0 The country is same CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0] eth0: Link speed: 1000BaseT FDX Device eth0: hwaddr 00-21-29-C6-61-00, ipaddr 192.168.1.1, mask 255.255.255.0 gateway not set, nameserver not set CMD: [go;] Check CRC of image1 Len: 0x717000 (7434240) (0xBC040000) Offset0: 0x1C (28) (0xBC04001C) Offset1: 0x1016DC (1054428) (0xBC1416DC) Offset2: 0x0 (0) (0xBC040000) Header CRC: 0x9E47184F Calculate CRC: 0x9E47184F Image 1 is OK Try to load image 1. CMD: [load -raw -addr=0x807a60b0 -max=0x3a0000 :] Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null) Loading: Failed. Could not load :: Timeout occured CMD: [boot -raw -z -addr=0x80001000 -max=0x3a0000 flash0.os:] Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: .. 2416640 bytes read Entry at 0x80001000 Closing network. eth0: cannot clear 1400/00000002 Starting program at 0x80001000 CPU revision is: 0002901a Primary instruction cache 32kb, linesize 16 bytes (4 ways) Primary data cache 32kb, linesize 16 bytes (2 ways) 2008 Setting the PFC to its default value Determined physical RAM map: memory: 04000000 @ 00000000 (usable) On node 0 totalpages: 16384 zone(0): 16384 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200 CPU: BCM4785 rev 2 at 300 MHz Calibrating delay loop... 299.82 BogoMIPS Memory: 62208k/65536k available (2119k kernel code, 3328k reserved, 144k data, 76k init, 0k highmem) Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) Inode cache hash table entries: 4096 (order: 3, 32768 bytes) Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 16384 (order: 4, 65536 bytes) Checking for 'wait' instruction... unavailable. POSIX conformance testing by UNIFIX PCI: Initializing host PCI: Fixing up bus 0 PCI: Fixing up bridge PCI: Fixing up bus 1 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 NTFS driver v1.1.22 [Flags: R/O] squashfs: version 3.0 (2006/03/15) Phillip Lougher pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0xb8000300 (irq = 8) is a 16550A ttyS01 at 0xb8000400 (irq = 0) is a 16550A HDLC line discipline: version $Revision$, maxframe=4096 N_HDLC line discipline registered. PPP generic driver version 2.4.2 Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension (NICE) ver. 8.3.14 (11/2/05) PHY ID unknown, assume it is a copper PHY. eth0: Broadcom BCM4785 10/100/1000 Integrated Controller found at mem 18010000, IRQ 5, node addr 002129c66100 eth0: Unknown transceiver found eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, NAPI ON SCSI subsystem driver Revision: 1.00 Amd/Fujitsu Extended Query Table v1.1 at 0x0040 number of CFI chips: 1 Flash device: 0x800000 at 0x1c000000 Physically mapped flash: squashfs filesystem found at block 1285 (Not Found Lang Block)off=0x1416dc off1=0x7e0000 size=0x800000 Creating 5 MTD partitions on "Physically mapped flash": 0x00000000-0x00040000 : "pmon" 0x00040000-0x007e0000 : "linux" 0x001416dc-0x007e0000 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only 0x007e0000-0x007f0000 : "lang" 0x007f0000-0x00800000 : "nvram" sflash: found no supported devices usb.c: registered new driver usbdevfs usb.c: registered new driver hub ehci_hcd 00:02.1: PCI device 14e4:471a ehci_hcd 00:02.1: irq 3, pci mem b8002800 usb.c: new USB bus registered, assigned bus number 1 ehci_hcd 00:02.1: illegal capability! ECHI PCI device 471a14e4 found. PCI: 00:02.1 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32 ehci_hcd 00:02.1: USB 0.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4 hub.c: USB hub found hub.c: 2 ports detected host/usb-uhci.c: $Revision: 1.2 $ time 21:04:02 Jun 2 2008 host/usb-uhci.c: High bandwidth mode enabled ECHI PCI device 471b14e4 found. host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver host/usb-ohci.c: USB OHCI at membase 0xb8002000, IRQ 3 host/usb-ohci.c: usb-00:02.0, PCI device 14e4:471a usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver usblp printer.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 8192) Linux IP multicast router 0.06 plus PIM-SM ip_conntrack version 2.1 (512 buckets, 4096 max) - 368 bytes per conntrack IPSEC isakmp Support Max Pass-through [50]. ip_conntrack_rtsp v0.01 loading ip_nat_rtsp v0.01 loading ip_tables: (C) 2000-2002 Netfilter core team ipt_time loading NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver NET4: Ethernet Bridge 008 for NET4.0 802.1Q VLAN Support v1.7 Ben Greear All bugs added by David S. Miller cramfs: wrong magic FAT: bogus logical sector size 19232 NTFS: Unable to set blocksize 512. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 76k freed Algorithmics/MIPS FPU Emulator v1.5 cmd=[insmod ctmisc ] Using /lib/modules/2.4.20/kernel/drivers/net/ctmisc/ctmisc.o Register /dev/ctmisc device, major:250 minor:0 The boot is CFE /dev/: cannot create cmd=[misc -t get_wsc_pin -w 3 ] type = [get_wsc_pin] get_data(): cmd=ctmisc_ioctl: cmd=0x26, buffer size=196 0x26 count=8 lendata_init(): base = 0xbc03fcdc =8 data_init(): location = [1], mydatas index = 1 ctmisc_ioctl: index=1 tallest:=====(ctmisc ioctl done...)===== get_data(): Get WSC count is [1] get_data(): WSC 0: [86328432] get_data(): done cmd=[misc -t get_mac -w 3 ] type = [get_mac] get_data(): cmd=ctmisc_ioctl: cmd=0x11, buffer size=196 0x11 count=8 lendata_init(): base = 0xbc001e00 =18 data_init(): location = [1], mydatas index = 1 ctmisc_ioctl: index=1 tallest:=====(ctmisc ioctl done...)===== get_data(): Get MAC count is [1] get_data(): MAC 0: [00:21:29:C6:61:00] get_data(): done cmd=[misc -t get_sn -w 3 ] type = [get_sn] get_data(): cmd=ctmisc_ioctl: cmd=0x15, buffer size=196 0x15 count=8 lendata_init(): base = 0xbc03fe30 =20 data_init(): location = [1], mydatas index = 1 ctmisc_ioctl: index=1 tallest:=====(ctmisc ioctl done...)===== get_data(): Get SN count is [1] get_data(): SN 0: [CTG01H700321] get_data(): done cmd=[misc -t get_country -w 3 ] type = [get_country] get_data(): cmd=ctmisc_ioctl: cmd=0x2c, buffer size=196 0x2c count=1 lendata_init(): base = 0xbc03fe2c =4 data_init(): location = [1], mydatas index = 1 ctmisc_ioctl: index=1 tallest:=====(ctmisc ioctl done...)===== get_data(): Get COUNTRY count is [1] get_data(): COUNTRY 0: [EU] get_data(): done cmd=[misc -t get_flash_type -w 1 ] type = [get_flash_type] ctmisc_ioctl: cmd=0x17, buffer size=196 get_flash_type()Try 4: vendor id = 0x007F, device id = 0x22CB : cmd=0x17 countEon EN29LV640B 4Mx16 BotB=0 len=0 Flash Type: Eon EN29LV640B 4Mx16 BotB tallest:=====(ctmisc ioctl done...)===== Get FLASH TYPE is [Eon EN29LV640B 4Mx16 BotB] ------ CT HW version is NULL ------ cmd=[misc -t get_pa2ga0idxval -w 3 ] type = [get_pa2ga0idxval] ctmisc_ioctl: cmd=0x28, buffer size=196 get_data(): cmd=data_init(): base = 0xbc03f6c0 0x28 count=8 lendata_init(): location = [1], mydatas index = 1 =24 ctmisc_ioctl: index=1 tallest:=====(ctmisc ioctl done...)===== get_data(): Get PA2GA0IDXVAL count is [1] get_data(): PA2GA0IDXVAL 0: [4 0xfeca 0x14a4 0xfb21] get_data(): done cmd=[misc -t get_pa2ga1idxval -w 3 ] type = [get_pa2ga1idxval] ctmisc_ioctl: cmd=0x2a, buffer size=196 get_data(): cmd=data_init(): base = 0xbc03f600 0x2a count=8 lendata_init(): location = [0], mydatas index = 0 =24 ctmisc_ioctl: index=0 tallest:=====(ctmisc ioctl done...)===== get_data(): Get PA2GA1IDXVAL count is [0] get_data(): done 2G idx[4] w0a0[0xfeca] w1a0[0x14a4] w2a0[0xfb21] Update [0xfeca] to [0xfeca] Update [0x14a4] to [0x14a4] Update [0xfb21] to [0xfb21] Using default 2G PA1 value cmd=[misc -t get_pa5gha0idxval -w 3 ] type = [get_pa5gha0idxval] ctmisc_ioctl: cmd=0x38, buffer size=196 get_data(): cmd=data_init(): base = 0xbc03f4c0 0x38 count=8 lendata_init(): location = [1], mydatas index = 1 =24 ctmisc_ioctl: index=1 tallest:=====(ctmisc ioctl done...)===== get_data(): Get PA5GHA0IDXVAL count is [1] get_data(): PA5GHA0IDXVAL 0: [6 0xfea6 0x134c 0xfb34] get_data(): done cmd=[misc -t get_pa5gha1idxval -w 3 ] type = [get_pa5gha1idxval] ctmisc_ioctl: cmd=0x3a, buffer size=196 get_data(): cmd=data_init(): base = 0xbc03f400 0x3a count=8 lendata_init(): location = [1], mydatas index = 1 =24 ctmisc_ioctl: index=1 tallest:=====(ctmisc ioctl done...)===== get_data(): Get PA5GHA1IDXVAL count is [1] get_data(): PA5GHA1IDXVAL 0: [6 0xfeac 0x12da 0xfb54] get_data(): done 5G high idx[6] w0a0[0xfea6] w1a0[0x134c] w2a0[0xfb34] Update [0xfea6] to [0xfea6] Update [0x134c] to [0x134c] Update [0xfb34] to [0xfb34] 5G high idx[6] w0a1[0xfeac] w1a1[0x12da] w2a1[0xfb54] Update [0xfeac] to [0xfeac] Update [0x12da] to [0x12da] Update [0xfb54] to [0xfb54] cmd=[misc -t get_pa5gla0idxval -w 3 ] type = [get_pa5gla0idxval] ctmisc_ioctl: cmd=0x48, buffer size=196 get_data(): cmd=data_init(): base = 0xbc03f2c0 0x48 count=8 lendata_init(): location = [0], mydatas index = 0 =24 ctmisc_ioctl: index=0 tallest:=====(ctmisc ioctl done...)===== get_data(): Get PA5GLA0IDXVAL count is [0] get_data(): done cmd=[misc -t get_pa5gla1idxval -w 3 ] type = [get_pa5gla1idxval] ctmisc_ioctl: cmd=0x4a, buffer size=196 get_data(): cmd=data_init(): base = 0xbc03f200 0x4a count=8 lendata_init(): location = [0], mydatas index = 0 =24 ctmisc_ioctl: index=0 tallest:=====(ctmisc ioctl done...)===== get_data(): Get PA5GLA1IDXVAL count is [0] get_data(): done Using default 5G low PA0 value Using default 5G low PA1 value cmd=[misc -t get_pa5ga0idxval -w 3 ] type = [get_pa5ga0idxval] ctmisc_ioctl: cmd=0x58, buffer size=196 get_data(): cmd=data_init(): base = 0xbc03f0c0 0x58 count=8 lendata_init(): location = [1], mydatas index = 1 =24 ctmisc_ioctl: index=1 tallest:=====(ctmisc ioctl done...)===== tallest:=====(ctmisc ioctl done...)===== get_data(): Get PA5GA0IDXVAL count is [1] get_data(): PA5GA0IDXVAL 0: [4 0xfead 0x134f 0xfb43] get_data(): done cmd=[misc -t get_pa5ga1idxval -w 3 ] type = [get_pa5ga1idxval] ctmisc_ioctl: cmd=0x5a, buffer size=196 get_data(): cmd=data_init(): base = 0xbc03f000 0x5a count=8 lendata_init(): location = [0], mydatas index = 0 =24 ctmisc_ioctl: index=0 tallest:=====(ctmisc ioctl done...)===== get_data(): Get PA5GA1IDXVAL count is [0] get_data(): done 5G middle idx[4] w0a0[0xfead] w1a0[0x134f] w2a0[0xfb43] Update [0xfead] to [0xfead] Update [0x134f] to [0x134f] Update [0xfb43] to [0xfb43] Using default 5G middle PA1 value Restoring Storage Nvram Defaults enter main_loop().. find "lang" in MSQUASHFS error: Can't find a SQUASHFS superblock on mtdblock(31,3) TD 3 (/dev/mtdblock/3) ret = -1 www -> /www mount: No such file or directory cmd=[touch /tmp/var/lib/nfs/xtab ] cmd=[chmod 644 /tmp/var/lib/nfs/xtab ] cmd=[touch /tmp/var/lib/nfs/etab ] cmd=[chmod 644 /tmp/var/lib/nfs/etab ] cmd=[touch /tmp/var/lib/nfs/rmtab ] cmd=[chmod 644 /tmp/var/lib/nfs/rmtab ] cmd=[touch /tmp/var/lib/nfs/state ] cmd=[chmod go-rwx /tmp/var/lib/nfs/state ] cmd=[touch /tmp/disk_updating_lock ] cmd=[chmod 644 /tmp/disk_updating_lock ] cmd=[touch /tmp/file_variable_updating_lock ] cmd=[chmod 644 /tmp/file_variable_updating_lock ] cmd=[insmod /lib/ufsd_cbtn.o ] Using /lib/ufsd_cbtn.o modules[0]=bcm57xx buf=[bcm57xx ] modules[1]=wl buf=[bcm57xx wl ] Needed modules: bcm57xx wl cmd=[insmod bcm57xx ] insmod: bcm57xx.o: no module by that name found cmd=[insmod wl ] Using /lib/modules/2.4.20/kernel/drivers/net/wl/wl.o Error reading /proc/partitions: invalid header. Failed trying to open `/proc/mdstat': No such file or directory Failed trying to open `/proc/sestat': No such file or directory Error reading /proc/partitions: invalid header. Failed trying to open `/proc/mdstat': No such file or directory Failed trying to open `/proc/sestat': No such file or directory Hit enter to continue...The chipset is BCM4705 + BCM5397 for EWC Make date==>Year:8,Month:6,Day:2 Firmware version =>v1.00.00 sum3=7435264 garbage=992 n=1024 MD5=[461cebecdf6b0d453ed225d2030de824] cmd=[killall httpd ] killall: httpd: no process killed cmd=[killall httpd ] killall: httpd: no process killed cmd=[resetbutton ] WARNING: console log level set to 1 cmd=[vconfig set_name_type VLAN_PLUS_VID_NO_PAD ] cmd=[vconfig add eth0 1 ] cmd=[vconfig set_ingress_map vlan1 0 0 ] cmd=[vconfig set_ingress_map vlan1 1 1 ] cmd=[vconfig set_ingress_map vlan1 2 2 ] cmd=[vconfig set_ingress_map vlan1 3 3 ] cmd=[vconfig set_ingress_map vlan1 4 4 ] cmd=[vconfig set_ingress_map vlan1 5 5 ] cmd=[vconfig set_ingress_map vlan1 6 6 ] cmd=[vconfig set_ingress_map vlan1 7 7 ] cmd=[vconfig add eth0 2 ] cmd=[vconfig set_ingress_map vlan2 0 0 ] cmd=[vconfig set_ingress_map vlan2 1 1 ] cmd=[vconfig set_ingress_map vlan2 2 2 ] cmd=[vconfig set_ingress_map vlan2 3 3 ] cmd=[vconfig set_ingress_map vlan2 4 4 ] cmd=[vconfig set_ingress_map vlan2 5 5 ] cmd=[vconfig set_ingress_map vlan2 6 6 ] cmd=[vconfig set_ingress_map vlan2 7 7 ] cmd=[brctl addbr br0 ] cmd=[brctl setfd br0 0 ] cmd=[brctl stp br0 dis ] name=[vlan1] lan_ifname=[br0] cmd=[brctl addif br0 vlan1 ] br0: No such file or directory cmd=[wlconf vlan1 up ] vlan1: Operation not supported name=[eth1] lan_ifname=[br0] Write wireless mac successfully cmd=[brctl addif br0 eth1 ] br0: No such file or directory cmd=[wlconf eth1 up ] eth1: Numerical result out of range eth1: Operation not supported eth1: Invalid argument eth1: Invalid argument eth1: Operation not supported eth1: Operation not supported eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument cmd=[brctl addif br0 eth1 ] device eth1 is already a member of a bridge; can't enslave it to bridge br0. name=[eth2] lan_ifname=[br0] Write wireless mac successfully cmd=[brctl addif br0 eth2 ] br0: No such file or directory cmd=[wlconf eth2 up ] eth2: Numerical result out of range eth2: Operation not supported eth2: Operation not supported eth2: Operation not supported cmd=[brctl addif br0 eth2 ] device eth2 is already a member of a bridge; can't enslave it to bridge br0. name=[eth3] lan_ifname=[br0] cmd=[brctl addif br0 eth3 ] interface eth3 does not exist! eth3: No such device module: wl c0068000 1172704 2 cmd=[wl gpiotimerval 0x640000 ] wl: No such file or directory cmd=[wl vlan_mode 0 ] wl: No such file or directory lo: File exists Set 66560 to /proc/sys/net/core/rmem_max ... cmd=[tftpd -s /tmp -c -l -P 610N ] cmd=[cron ] The boot is CFE tftp server started tftpd: standalone socket cron: No such file or directory cron: created [HTTPD Starting on /www] cmd=[httpd ] cmd=[dnsmasq -h -i br0 -r /tmp/resolv.conf ] br0 192.168.1.100 86400 cmd=[udhcpd /tmp/udhcpd.conf ] info, udhcp server (v0.9.8) started cmd=[/bin/wsccmd ] cmd=[nas /tmp/nas.lan.conf /tmp/nas.lan.pid lan ] zebra disabled. No disk, do not start samba. cmd=[killall twonkymedia ] killall: twonkymedia: no process killed cmd=[killall twonkymediaserv ] killall: twonkymediaserv: no process killed cmd=[killall twonkymediaserver ] eth1: ignore i/f due to error(s) eth2: ignore i/f due to error(s) killall: twonkymediaserver: no process killed cmd=[upnp -D -L br0 -W -S 0 -I 60 -A 180 ] ********************************************* Wi-Fi Simple Config Application - Intel Corp. Version: Build 1.0.5, November 19 2006 ********************************************* calling upnp_main lltd:echo WRT610N > /proc/sys/kernel/hostname Initializing stack...button monitor start...! OK Now starting stack LLTD: wireless interface argument is eth1. get mac = 00 21 29 C6 61 02 Using /bin/eghn_kernel_module.o IP is 101a8c0 mask is ffffff cmd=[tc qdisc del dev vlan1 root ] RTNETLINK answers: No such file or directory cmd=[tc qdisc del dev eth1 root ] RTNETLINK answers: No such file or directory Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.1.1 port = 49152 Specifying the webserver root directory -- /var/EGHN_QPH Registering the RootDevice with desc_doc_url: http://192.168.1.1:49152/qphdevicedesc.xml RootDevice Registered Initializing State Table Found service: urn:schemas-upnp-org:service:QosPolicyHolder:2 serviceId: urn:upnp-org:serviceId:QosPolicyHolder-1 State Table Initialized cmd=[tc qdisc del dev eth2 root ] RTNETLINK answers: No such file or directory cmd=[sh /tmp/cmdfile134 ] Advertisements Sent cmd=[dhcp6s -c /tmp/dhcp6s.conf br0 ] Dispay orig configurations cmd=[cat /tmp/cmdfile134 ] tc qdisc add dev vlan1 root handle 1: prio bands 8 priomap 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 tc qdisc add dev vlan1 parent 1:1 handle 10: pfifo limit 20 tc qdisc add dev vlan1 parent 1:2 handle 20: pfifo limit 20 tc qdisc add dev vlan1 parent 1:3 handle 30: pfifo limit 20 tc qdisc add dev vlan1 parent 1:4 handle 40: pfifo limit 20 tc qdisc add dev vlan1 parent 1:5 handle 50: pfifo limit 20 tc qdisc add dev vlan1 parent 1:6 handle 60: pfifo limit 20 tc qdisc add dev vlan1 parent 1:7 handle 70: pfifo limit 20 tc qdisc add dev vlan1 parent 1:8 handle 80: pfifo limit 20 tc filter add dev vlan1 parent 1:0 prio 5 protocol all tcindex mask 0xff shift 0 pass_on tc filter add dev vlan1 parent 1:0 prio 5 handle 0 tcindex classid 1:6 tc filter add dev vlan1 parent 1:0 prio 5 handle 1 tcindex classid 1:8 tc filter add dev vlan1 parent 1:0 prio 5 handle 2 tcindex classid 1:7 tc filter add dev vlan1 parent 1:0 prio 5 handle 3 tcindex classid 1:5 tc filter add dev vlan1 parent 1:0 prio 5 handle 4 tcindex classid 1:4 tc filter add dev vlan1 parent 1:0 prio 5 handle 5 tcindex classid 1:3 tc filter add dev vlan1 parent 1:0 prio 5 handle 6 tcindex classid 1:2 tc filter add dev vlan1 parent 1:0 prio 5 handle 7 tcindex classid 1:1 cmd=[sh /tmp/cmdfile134 ] cmd=[killall -1 radvd ] DEVICE PIN: 86328432 UdpLib: Entered udp_open UdpLib: Socket open successful, sd: 9 UdpLib: Entered udp_bind UdpLib: Binding successful for socket [9] UdpLib: Entered udp_read ******* MODE: Access Point ******* DEVICE PIN:86328432 WSC: In unconfiged AP mode, wait for start command.... tlvPtrChar* : func CMasterControl_InitiateRegistration line 658 allocating memory 0x10003700 for 0x100036e8 UdpLib: Entered udp_open UdpLib: Socket open successful, sd: 10 UdpLib: Entered udp_bind UdpLib: Binding successful for socket [10] UdpLib: Entered udp_read UdpLib: Entered udp_read killall: radvd: no process killed Waiting for Registrar to connect... tallest:=====( wan_or_lan=wan )===== tallest:=====( wan_or_lan=wan is wan !!)===== cmd=[udhcpc -i vlan2 -l br0 -p /var/run/wan_udhcpc.pid -s /tmp/udhcpc ] info, udhcp client (v0.9.8) started cmd=[nas /tmp/nas.wan.conf /tmp/nas.wan.pid wan ] cmd=[dhcp6s -c /tmp/dhcp6s.conf br0 ] Hit enter to continue...No interface specified. Quitting... Hit enter to continue...Hit enter to continue...cmd=[sh /tmp/cmdfile134 ] Hit enter to continue...


Bug Tracking Ticket

https://dev.openwrt.org/ticket/3857

Vendor Source

ftp://ftp.linksys.com/opensourcecode/wrt610n/

OpenWrt System Information

See sysinfo.

OpenWrt SoC Status

See soc.broadcom.bcm47xx

For WIFI config with wl

Consult https://dev.openwrt.org/ticket/5788 (don't choose an unsupported mode)

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1