Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
toh:linksys:wrt150n [2012/02/25 11:41] – created uncloudedtoh:linksys:wrt150n [2019/10/10 13:37] someothertime
Line 1: Line 1:
 +====== Linksys WRT150N ======
  
 +{{section>meta:infobox:432_warning#infobox_for_dataentries&noheader&nofooter&noeditbutton}}
 +
 +  * tried r39412 and it works without issues
 +  * below is nvram without correction from '/etc/init.d/nvram (mtd erase mtd6 + reboot)
 +  * then boot/klog/dmesg from r39412
 +  * and some some old stuff
 +
 +<code>
 +root@OpenWrt:/# nvram show | sort
 +blink_diag_led=1
 +boardflags2=0
 +boardflags=0x0010
 +boardnum=42
 +boardrev=0x10
 +boardtype=0x0472
 +boot_hw_model=WRT150N
 +boot_hw_ver=1
 +boot_ver=v4.3
 +boot_wait=off
 +bootnv_ver=2
 +cardbus=1
 +clkfreq=264
 +diag_gpio=1
 +dl_ram_addr=a0001000
 +et0macaddr=00:1c:10:19:a4:e6
 +et0mdcport=0
 +et0phyaddr=30
 +et1macaddr=00:88:88:88:00:2a
 +et1mdcport=0
 +et1phyaddr=4
 +lan_ipaddr=192.168.1.1
 +lan_netmask=255.255.255.0
 +mfg_wait=on
 +os_flash_addr=bfc40000
 +os_ram_addr=80001000
 +parkid=0
 +pci/1/1/aa2g=3
 +pci/1/1/ag0=2
 +pci/1/1/ag1=2
 +pci/1/1/ag2=2
 +pci/1/1/boardflags2=1
 +pci/1/1/boardflags=0x200
 +pci/1/1/boardrev=0x4b
 +pci/1/1/boardtype=0x46d
 +pci/1/1/boardvendor=0x14e4
 +pci/1/1/bw40po=0
 +pci/1/1/bwduppo=0
 +pci/1/1/ccdpo=0
 +pci/1/1/cck2gpo=0
 +pci/1/1/ccode=
 +pci/1/1/devid=0x4329
 +pci/1/1/itt2ga0=0
 +pci/1/1/itt2ga1=0
 +pci/1/1/ledbh0=8
 +pci/1/1/ledbh1=-1
 +pci/1/1/ledbh2=-1
 +pci/1/1/ledbh3=-1
 +pci/1/1/macaddr=00:88:88:88:00:2a
 +pci/1/1/maxp2ga0=0
 +pci/1/1/maxp2ga1=0
 +pci/1/1/mcs2gpo0=0
 +pci/1/1/mcs2gpo1=0
 +pci/1/1/mcs2gpo2=0
 +pci/1/1/mcs2gpo3=0
 +pci/1/1/mcs2gpo4=0
 +pci/1/1/mcs2gpo5=0
 +pci/1/1/mcs2gpo6=0
 +pci/1/1/mcs2gpo7=0
 +pci/1/1/ofdm2gpo=0
 +pci/1/1/pa2gw0a0=0
 +pci/1/1/pa2gw0a1=0
 +pci/1/1/pa2gw1a0=0
 +pci/1/1/pa2gw1a1=0
 +pci/1/1/pa2gw2a0=0
 +pci/1/1/pa2gw2a1=0
 +pci/1/1/pa2gw3a0=0
 +pci/1/1/pa2gw3a1=0
 +pci/1/1/regrev=0
 +pci/1/1/sromrev=4
 +pci/1/1/stbcpo=0
 +pci/1/1/txpid2ga0=91
 +pci/1/1/txpid2ga1=91
 +pci/1/1/txpt2g=0x36
 +pci/1/1/venid=0x14e4
 +pmon_ver=CFE 4.101.27.0
 +scratch=a0180000
 +sdram_config=0x0062
 +sdram_init=0x054B
 +sdram_ncdl=0x208
 +sdram_refresh=0x0
 +sromrev=4
 +tftpd_ipaddr=192.168.1.254
 +wait_time=3
 +watchdog=5000
 +wl0gpio0=8
 +</code>
 +
 +klog/dmesg:
 +<WRAP bootlog>
 +<nowiki>   0.000000] Linux version 3.10.28 (openwrt@snapon) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39412) ) #1 Wed Jan 29 08:21:17 PST 2014
 +[    0.000000] CPU revision is: 00029006 (Broadcom BMIPS3300)
 +[    0.000000] bcm47xx: using ssb bus
 +[    0.000000] ssb: Found chip with id 0x4704, rev 0x09 and package 0x00
 +[    0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
 +[    0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
 +[    0.000000] ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
 +[    0.000000] ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
 +[    0.000000] ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
 +[    0.000000] ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
 +[    0.000000] ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
 +[    0.000000] ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
 +[    0.000000] ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
 +[    0.000000] ssb: chipcommon status is 0x0
 +[    0.000000] ssb: Initializing MIPS core...
 +[    0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
 +[    0.000000] ssb: set_irq: core 0x0806, irq 5 => 5
 +[    0.000000] ssb: set_irq: core 0x0808, irq 6 => 2
 +[    0.000000] ssb: set_irq: core 0x0804, irq 2 => 6
 +[    0.000000] ssb: after irq reconfiguration
 +[    0.000000] ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I 
 +[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I 
 +[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4  5* 6  D  I 
 +[    0.000000] ssb: core 0x0808, irq : 2(S)* 3  4  5  6  D  I 
 +[    0.000000] ssb: core 0x0804, irq : 2(S)  3  4  5  6* D  I 
 +[    0.000000] ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I 
 +[    0.000000] ssb: core 0x0807, irq : 2(S)* 3  4  5  6  D  I 
 +[    0.000000] ssb: core 0x080b, irq : 2(S)* 3  4  5  6  D  I 
 +[    0.000000] ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
 +[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
 +[    0.000000] MIPS: machine is Linksys WRT150N V1
 +[    0.000000] Determined physical RAM map:
 +[    0.000000]  memory: 01000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000]   Normal   [mem 0x00000000-0x00ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000]   node   0: [mem 0x00000000-0x00ffffff]
 +[    0.000000] On node 0 totalpages: 4096
 +[    0.000000] free_area_init_node: node 0, pgdat 802dcbe0, node_mem_map 8035b000
 +[    0.000000]   Normal zone: 32 pages used for memmap
 +[    0.000000]   Normal zone: 0 pages reserved
 +[    0.000000]   Normal zone: 4096 pages, LIFO batch:0
 +[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc: [0] 0 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
 +[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
 +[    0.000000] PID hash table entries: 64 (order: -4, 256 bytes)
 +[    0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.000000] Memory: 12748k/16384k available (2416k kernel code, 3636k reserved, 592k data, 184k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.070000] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
 +[    0.070000] pid_max: default: 32768 minimum: 301
 +[    0.070000] Mount-cache hash table entries: 512
 +[    0.070000] NET: Registered protocol family 16
 +[    0.110000] bio: create slab <bio-0> at 0
 +[    0.120000] Switching to clocksource MIPS
 +[    0.130000] ssb: PCIcore in host mode found
 +[    0.430000] PCI host bridge to bus 0000:00
 +[    0.430000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
 +[    0.430000] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
 +[    0.430000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
 +[    0.430000] pci 0000:00:00.0: [14e4:4704] type 00 class 0x060000
 +[    0.430000] ssb: PCI: Fixing up bridge 0000:00:00.0
 +[    0.430000] pci 0000:00:00.0: setting latency timer to 64
 +[    0.430000] ssb: PCI: Fixing up device 0000:00:00.0
 +[    0.430000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
 +[    0.430000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x00001fff]
 +[    0.430000] pci 0000:00:00.0: reg 14: [mem 0x00000000-0x07ffffff pref]
 +[    0.430000] pci 0000:00:01.0: [14e4:4321] type 00 class 0x028000
 +[    0.430000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00003fff]
 +[    0.430000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
 +[    0.430000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
 +[    0.440000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
 +[    0.440000] ssb: PCI: Fixing up device 0000:00:01.0
 +[    0.440000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64
 +[    0.480000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
 +[    0.480000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x12, vendor 0x4243)
 +[    0.480000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0B, vendor 0x4243)
 +[    0.480000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x02, vendor 0x4243)
 +[    0.480000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0D, vendor 0x4243)
 +[    0.480000] ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243)
 +[    0.520000] ssb: chipcommon status is 0x0
 +[    0.520000] ssb: SPROM offset is 0x1000
 +[    0.540000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22
 +[    0.540000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22
 +[    0.540000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22
 +[    0.690000] ssb: Using SPROM revision 4 provided by platform
 +[    0.730000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
 +[    0.730000] NET: Registered protocol family 2
 +[    0.730000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
 +[    0.730000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
 +[    0.740000] TCP: Hash tables configured (established 512 bind 512)
 +[    0.740000] TCP: reno registered
 +[    0.740000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.740000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.740000] NET: Registered protocol family 1
 +[    0.740000] PCI: CLS 0 bytes, default 16
 +[    0.750000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    0.750000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.750000] msgmni has been set to 24
 +[    0.750000] io scheduler noop registered
 +[    0.750000] io scheduler deadline registered (default)
 +[    0.750000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
 +[    0.790000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
 +[    1.140000] console [ttyS0] enabled
 +[    1.160000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
 +[    1.180000] physmap platform flash device: 02000001 at 1c000000
 +[    1.180000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x0022f6
 +[    1.200000] physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
 +[    1.200000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
 +[    1.200000] physmap-flash.0: Found an alias at 0xc00000 for the chip at 0x0
 +[    1.200000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
 +[    1.200000] physmap-flash.0: Found an alias at 0x1400000 for the chip at 0x0
 +[    1.200000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
 +[    1.200000] physmap-flash.0: Found an alias at 0x1c00000 for the chip at 0x0
 +[    1.200000] Amd/Fujitsu Extended Query Table at 0x0040
 +[    1.200000]   Amd/Fujitsu Extended Query version 1.1.
 +[    1.210000] physmap-flash.0: Swapping erase regions for top-boot CFI table.
 +[    1.210000] number of CFI chips: 1
 +[    1.220000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
 +[    1.230000] Creating 6 MTD partitions on "physmap-flash.0":
 +[    1.230000] 0x000000000000-0x000000040000 : "boot"
 +[    1.240000] 0x000000040000-0x0000003f0000 : "firmware"
 +[    1.250000] 0x00000004001c-0x000000040960 : "loader"
 +[    1.260000] 0x000000040960-0x000000149c00 : "linux"
 +[    1.270000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    1.290000] 0x000000149c00-0x0000003f0000 : "rootfs"
 +[    1.290000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    1.310000] mtd: device 4 (rootfs) set to be root filesystem
 +[    1.310000] mtd: partition "rootfs_data" created automatically, ofs=0x320000, len=0xd0000
 +[    1.320000] 0x000000320000-0x0000003f0000 : "rootfs_data"
 +[    1.330000] 0x0000003f0000-0x000000400000 : "nvram"
 +[    1.360000] libphy: Fixed MDIO Bus: probed
 +[    1.360000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
 +[    1.370000] GPIO_WDT: failed to register misc device
 +[    1.380000] TCP: cubic registered
 +[    1.380000] NET: Registered protocol family 17
 +[    1.390000] Bridge firewalling registered
 +[    1.390000] can: controller area network core (rev 20120528 abi 9)
 +[    1.400000] NET: Registered protocol family 29
 +[    1.400000] 8021q: 802.1Q VLAN Support v1.8
 +[    1.420000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
 +[    1.430000] Freeing unused kernel memory: 184K (802f2000 - 80320000)
 +[    6.390000] pps_core: LinuxPPS API ver. 1 registered
 +[    6.390000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
 +[    6.410000] PTP clock support registered
 +[    6.420000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
 +[    6.440000] libphy: b44_eth_mii: probed
 +[    6.460000] b53_common: found switch: BCM5325, rev 0
 +[    6.460000] b44 ssb0:0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=1:1e)
 +[    6.470000] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1c:10:19:a4:e6
 +[    6.490000] libphy: b44_eth_mii: probed
 +[    6.490000] b44 ssb0:1: could not find PHY at 4, use fixed one
 +[    6.500000] b44 ssb0:1: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00)
 +[    6.500000] b44 ssb0:1 eth1: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:88:88:88:00:2a
 +[    6.520000] bgmac: Broadcom 47xx GBit MAC driver loaded
 +[    7.150000] b44 ssb0:0 eth0: Link is up at 100 Mbps, half duplex
 +[    7.160000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
 +[   11.940000] b44 ssb0:0 eth0: powering down PHY
 +[   20.210000] NET: Registered protocol family 10
 +[   20.240000] nf_conntrack version 0.5.0 (202 buckets, 808 max)
 +[   20.260000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[   20.310000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
 +[   20.320000] Backport generated by backports.git backports-20130802-0-gdb67a3f
 +[   20.340000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   20.440000] xt_time: kernel timezone is -0000
 +[   20.490000] cfg80211: Calling CRDA to update world regulatory domain
 +[   20.500000] cfg80211: World regulatory domain updated:
 +[   20.500000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
 +[   20.510000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   20.520000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   20.520000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   20.530000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
 +[   20.540000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
 +[   20.550000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
 +[   22.910000] PPP generic driver version 2.4.2
 +[   23.410000] NET: Registered protocol family 24
 +[   24.080000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
 +[   25.060000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
 +[   25.990000] Broadcom 43xx driver loaded [ Features: PNL ]
 +[   26.560000] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
 +[   26.590000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
 +[   40.550000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
 +[   40.590000] jffs2_build_filesystem(): unlocking the mtd device... done.
 +[   40.590000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
 +[   49.200000] jffs2: notice: (621) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 +[   54.270000] b44 ssb0:0 eth0: Link is up at 100 Mbps, half duplex
 +[   54.270000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
 +[   54.290000] device eth0 entered promiscuous mode
 +[   54.310000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
 +[   54.440000] b44 ssb0:1 eth1: Link is up at 100 Mbps, half duplex
 +[   54.450000] b44 ssb0:1 eth1: Flow control is off for TX and off for RX
 +[   55.320000] br-lan: port 1(eth0) entered forwarding state
 +[   55.320000] br-lan: port 1(eth0) entered forwarding state
 +[   55.330000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 +[   55.710000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
 +[   57.320000] br-lan: port 1(eth0) entered forwarding state</nowiki>
 +</WRAP>\\
 +
 +==== An account of flashing OpenWrt to a WRT150N ====
 +
 +  * The router is a LinkSys WRT150N.  No version is shown on the device.  The serial number begins ''CQ6..''
 +  * Did a 30/30/30 reset
 +  * Joined a laptop to the router with a patch cable
 +  * Configured the laptop as ''192.168.1.2''
 +  * Browsed to ''192.168.1.1''
 +  * Username: ''admin'', Password: ''admin''
 +  * Navigated to //Administration//, //Firmware Upgrade//
 +  * NOTE: This image is old -> please visit [[http://downloads.openwrt.org/releases/18.06.4/targets/brcm47xx/legacy/]]
 +  * legacy Uploaded [[http://downloads.openwrt.org/kamikaze/8.09.2/brcm-2.4/openwrt-wrt150n-squashfs.bin]]
 +
 +After a short while, ''nmap -F 192.168.1.1'' showed:
 +
 +  PORT   STATE SERVICE
 +  22/tcp open  ssh
 +  23/tcp open  telnet
 +  53/tcp open  domain
 +  80/tcp open  http
 +
 +[[docs:techref:hardware:soc:soc.broadcom.bcm47xx:image.conversion]]
 +
 +
 +  route add default gw 192.168.1.2  # assuming .2 is your laptop
 +  vi /etc/resolv.conf  # to tell OpenWrt where the DNS recursor is
 +  opkg update
 +  opkg install kmod-brcm-wl-mimo
 +  reboot
 +
 +
 +==== Why you should use brcm-2.4 ====
 +
 +The ''brcm47xx'' flavour of ''10.03.1'' will yield:
 +
 +  b43-phy0: Broadcom 4321 WLAN found (core revision 11)
 +  b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 5, Type 4, Revision 1)
 +  b43: probe of ssb1:0 failed with error -122
 +
 +..in the kernel log and no wireless interface.
 +
 +
 +==== Hardware ====
 +
 +''/proc/cpuinfo'':
 +
 +  system type : Broadcom BCM4704 chip rev 9
 +  processor : 0
 +  cpu model : BCM3302 V0.6
 +  BogoMIPS : 263.78
 +  wait instruction : no
 +  microsecond timers : yes
 +  tlb_entries : 32
 +  extra interrupt vector : no
 +  hardware watchpoint : no
 +  VCED exceptions : not available
 +  VCEI exceptions : not available
 +
 +''/proc/pci'':
 +
 +  PCI devices found:
 +    Bus  0, device   0, function  0:
 +      Class 0501: PCI device 14e4:0800 (rev 9).
 +        IRQ 3.
 +        Non-prefetchable 32 bit memory at 0x18000000 [0x18000fff].
 +        Non-prefetchable 32 bit memory at 0x1fc00000 [0x1fffffff].
 +        Non-prefetchable 32 bit memory at 0x1c000000 [0x1dffffff].
 +        Non-prefetchable 32 bit memory at 0x1a000000 [0x1bffffff].
 +    Bus  0, device   1, function  0:
 +      Class 0200: PCI device 14e4:4713 (rev 9).
 +        IRQ 4.
 +        Master Capable.  Latency=64.  
 +        Non-prefetchable 32 bit memory at 0x18001000 [0x18001fff].
 +    Bus  0, device   2, function  0:
 +      Class 0200: PCI device 14e4:4713 (rev 9).
 +        IRQ 5.
 +        Master Capable.  Latency=64.  
 +        Non-prefetchable 32 bit memory at 0x18002000 [0x18002fff].
 +    Bus  0, device   3, function  0:
 +      Class 0c03: PCI device 14e4:4715 (rev 9).
 +        IRQ 6.
 +        Non-prefetchable 32 bit memory at 0x18003000 [0x18003fff].
 +    Bus  0, device   4, function  0:
 +      Class 0604: PCI device 14e4:0804 (rev 9).
 +        IRQ 2.
 +        Non-prefetchable 32 bit memory at 0x18004000 [0x18004fff].
 +        Non-prefetchable 32 bit memory at 0x8000000 [0xfffffff].
 +    Bus  0, device   5, function  0:
 +      Class 0b30: PCI device 14e4:0816 (rev 9).
 +        IRQ 2.
 +        Non-prefetchable 32 bit memory at 0x18005000 [0x18005fff].
 +    Bus  0, device   6, function  0:
 +      Class 0703: PCI device 14e4:4712 (rev 9).
 +        IRQ 2.
 +        Non-prefetchable 32 bit memory at 0x18006000 [0x18006fff].
 +    Bus  0, device   7, function  0:
 +      Class 1000: PCI device 14e4:4718 (rev 9).
 +        IRQ 2.
 +        Non-prefetchable 32 bit memory at 0x18007000 [0x18007fff].
 +    Bus  0, device   8, function  0:
 +      Class 0500: PCI device 14e4:080f (rev 9).
 +        IRQ 3.
 +        Non-prefetchable 32 bit memory at 0x18008000 [0x18008fff].
 +        Non-prefetchable 32 bit memory at 0x0 [0x7ffffff].
 +        Non-prefetchable 32 bit memory at 0x10000000 [0x17ffffff].
 +        Non-prefetchable 32 bit memory at 0x80000000 [0x9fffffff].
 +    Bus  1, device   0, function  0:
 +      Class 0600: PCI device 14e4:4704 (rev 9).
 +        IRQ 2.
 +        Master Capable.  Latency=64.  
 +        Non-prefetchable 32 bit memory at 0x40000000 [0x40001fff].
 +        Prefetchable 32 bit memory at 0x0 [0x7ffffff].
 +    Bus  1, device   1, function  0:
 +      Class 0280: PCI device 14e4:4321 (rev 1).
 +        IRQ 2.
 +        Master Capable.  Latency=64.  
 +        Non-prefetchable 32 bit memory at 0x40004000 [0x40007fff].
 +===== Tags =====
 +{{tag>bcm47xx bcm4704}}
  • Last modified: 2019/10/11 04:08
  • by someothertime