Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:linksys:wap300n [2015/11/30 21:14] – [[meta:tags]] -> [[meta:tags|How to add tags]] tmomas | toh:linksys:wap300n [2020/10/12 05:15] – [Linksys WAP300N] funman | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ---- | ||
| + | ====== Linksys WAP300N ====== | ||
| + | |||
| + | Linksys WAP300N simple wireless router which has 2 detachable antennas and 1 LAN connection. | ||
| + | |||
| + | **Currently SoC is not supported.** | ||
| + | |||
| + | You can apply [[http:// | ||
| + | |||
| + | Generate an uBoot image with: | ||
| + | |||
| + | < | ||
| + | mipsel-linux-gnu-objcopy -O binary -R .note -R .comment -S vmlinux zImage | ||
| + | lzma -9 -f -S .lzma zImage | ||
| + | mkimage -A mips -O linux -T kernel -C lzma -a 80020000 -e 80020000 -n "Linux Kernel Image" | ||
| + | </ | ||
| + | |||
| + | then serve that um_factory_fw.bin via tftp from 192.168.1.100 to 192.168.1.1 | ||
| + | ===== Versions ===== | ||
| + | ^ Version/ | ||
| + | | v1 | ||
| + | |||
| + | |||
| + | **NOTE:** Anything not included in model specific notes, or where a short comment couldn' | ||
| + | |||
| + | |||
| + | |||
| + | ===== Hardware Highlights ===== | ||
| + | |||
| + | ^ Ver ^ CPU ^ Ram ^ Flash ^ Network ^ Wireless ^ USB ^ Serial ^ JTag ^ Wiki ^ FCC ^ | ||
| + | | v1 | Ralink RT6856F | 64MiB | 8MiB | 1x WAN | RT5592 | No | Yes | [[#notes]] | | Q87-WAP300N | | ||
| + | |||
| + | Manufacturer' | ||
| + | |||
| + | Forum: [[https:// | ||
| + | |||
| + | |||
| + | |||
| + | ==== Flash Layout ==== | ||
| + | ^ Layer0 | raw flash |||| | ||
| + | ^ Layer1 | Bootloader | ||
| + | ^ Layer2 | U-Boot 1.1.3 |:::|:::| LZMA uImage | | ||
| + | ^ Layer3 |::: | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | === Specific values you need === | ||
| + | |||
| + | | Bootloader tftp client IPv4 address | 192.168.1.1 | | ||
| + | | Firmware tftp image | um_factory_fw.bin | | ||
| + | | TFTP Transfer Window | FILL-IN seconds | | ||
| + | | TFTP Window Start | approximately FILL-IN seconds after power on | | ||
| + | | TFTP Server Required IP Address | 192.168.1.100 | | ||
| + | |||
| + | |||
| + | |||
| + | ==== Failsafe mode ==== | ||
| + | -> [[docs: | ||
| + | |||
| + | ==== Buttons ==== | ||
| + | -> [[docs: | ||
| + | |||
| + | The Linksys WAP300N has two buttons. They are Reset and Secure Easy Setup. Here, we merely name the buttons, so we can use them in the above Howto: | ||
| + | ^ BUTTON ^ Event ^ | ||
| + | | Reset | reset | | ||
| + | | Secure Easy Setup | ses | | ||
| + | |||
| + | |||
| + | ===== Hardware ===== | ||
| + | ==== Info ==== | ||
| + | | **[[wp> | ||
| + | | **Vendor: | ||
| + | | **[[docs: | ||
| + | | **[[docs: | ||
| + | | **[[docs: | ||
| + | | **Flash size: | ||
| + | | **Flash Chip: | ||
| + | | **RAM size: | ||
| + | | **RAM Chip: | ||
| + | | **Wireless No1: | ||
| + | | **[[docs: | ||
| + | | **USB: | ||
| + | | **[[docs: | ||
| + | | **[[docs: | ||
| + | |||
| + | ==== Photos ==== | ||
| + | Model Number | ||
| + | |||
| + | //Front:// | ||
| + | |||
| + | **Photo of front of the casing** | ||
| + | |||
| + | //Back:// | ||
| + | |||
| + | **Photo of back of the casing** | ||
| + | |||
| + | ==== Opening the case ==== | ||
| + | **Note:** This will void your warranty! | ||
| + | |||
| + | * To remove the cover remove **3** plastic bumpers back of the device and screws. | ||
| + | |||
| + | {{https:// | ||
| + | |||
| + | //Main PCB// | ||
| + | |||
| + | **Photo of PCB** | ||
| + | |||
| + | [[https:// | ||
| + | |||
| + | ==== Serial ==== | ||
| + | -> [[docs: | ||
| + | |||
| + | How to connect to the Serial Port of this specific device: | ||
| + | |||
| + | **Photo of PCB with markings** | ||
| + | {{media: | ||
| + | ==== JTAG ==== | ||
| + | -> [[docs: | ||
| + | |||
| + | How to connect to the JTAG Port of this specific device: | ||
| + | |||
| + | **Photo of PCB with markings** | ||
| + | |||
| + | {{https:// | ||
| + | |||
| + | |||
| + | ===== Debricking ===== | ||
| + | -> [[docs: | ||
| + | |||
| + | ===== Bootloader Mods ===== | ||
| + | |||
| + | Currently none. | ||
| + | |||
| + | ===== OEM info ===== | ||
| + | <WRAP bootlog>< | ||
| + | Linux version 2.6.36-svn14734 (root@SWRD) (gcc version 3.4.2) #1 Thu Mar 10 15:30:34 CST 2016 | ||
| + | # cat / | ||
| + | es=1 root=/ | ||
| + | # cat / | ||
| + | system type : Ralink RT63165 SOC | ||
| + | processor | ||
| + | cpu model : MIPS 34Kc V5.5 | ||
| + | BogoMIPS | ||
| + | wait instruction | ||
| + | microsecond timers | ||
| + | tlb_entries | ||
| + | extra interrupt vector | ||
| + | hardware watchpoint | ||
| + | ASEs implemented | ||
| + | shadow register sets : 1 | ||
| + | core : 0 | ||
| + | VCED exceptions | ||
| + | VCEI exceptions | ||
| + | # free | ||
| + | total | ||
| + | Mem: 61400 30212 31188 0 0 | ||
| + | | ||
| + | Total: | ||
| + | # cat / | ||
| + | dev: size | ||
| + | mtd0: 00800000 00010000 " | ||
| + | mtd1: 00030000 00010000 " | ||
| + | mtd2: 00010000 00010000 " | ||
| + | mtd3: 00010000 00010000 " | ||
| + | mtd4: 007b0000 00010000 " | ||
| + | </ | ||
| + | </ | ||
| + | |||
| + | ===== Bootlogs ===== | ||
| + | ==== OEM bootlog ==== | ||
| + | |||
| + | <WRAP bootlog> | ||
| + | < | ||
| + | |||
| + | Board: Ralink APSoC DRAM: 64 MB | ||
| + | relocate_code Pointer at: 83f18000 | ||
| + | </ | ||
| + | </ | ||
| + | |||
| + | ==== OpenWrt bootlog ==== | ||
| + | |||
| + | <WRAP bootlog> | ||
| + | < | ||
| + | </ | ||
| + | |||
| + | ===== Notes ===== | ||
| + | |||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta: | ||
| + | {{tag> | ||