Linksys MX4300
No 160MHz, it isn't supported by the IPQ8174.
The Linksys MX4300 (LN1301) is similar to the Linksys MX4200v2
Supported Versions
Potential Limitations and issue
- Ath11k memory: The ath11k driver needed for the main wireless radios uses a lot of memory when there are few stations connected and low bandwidth traffic flowing.
- NSS acceleration: the Qualcom NSS hardware acceleration is not available and maybe never will be. There is a community effort to enable it in the forum but this does not guarantee that it will be officially supported in the future.
- The IPQ807x target has not yet support for DSA, on OpenWrt: See this forum post. The regular DSA instructions on the mini tutorial do demonstrably work however; wireless interfaces need to be set up in the Network→Wireless section and then be bridged in their Interface Configuration→General Setup→Network menu to connect them to wired interfaces, and the contributor making this statement only uses tagged VLANs on the wired ports.
Hardware Highlights
Installation
Installation instructions
1. Open Linksys Web UI - http://192.168.1.1/ or http://10.65.1.1/ depending on your setup.
2. Login with your admin password. The default password can be found on a sticker under the device.
3. To enter into the support mode, click on the “CA” link and the bottom of the page.
4. Open the “Connectivity” menu and upload the squash-factory.bin image with the “Choose file” button. If there's no button, go to the hidden manual upgrade page - https://192.168.1.1/fwupdate.html, bypass the encryption error if necessary, select your OpenWrt firmware file, enter your router password and click “Update”.
5. Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
6. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
7. Then you would need to write openwrt to the other partition for it to work
8. First Check booted partition
fw_printenv -n boot_part
9. Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
*If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
Flash Layout
OEM Firmware
/ $ cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "0:SBL1" mtd1: 00100000 00020000 "0:MIBIB" mtd2: 00080000 00020000 "0:BOOTCONFIG" mtd3: 00080000 00020000 "0:BOOTCONFIG1" mtd4: 00300000 00020000 "0:QSEE" mtd5: 00300000 00020000 "0:QSEE_1" mtd6: 00080000 00020000 "0:DEVCFG" mtd7: 00080000 00020000 "0:DEVCFG_1" mtd8: 00080000 00020000 "0:APDP" mtd9: 00080000 00020000 "0:APDP_1" mtd10: 00080000 00020000 "0:RPM" mtd11: 00080000 00020000 "0:RPM_1" mtd12: 00080000 00020000 "0:CDT" mtd13: 00080000 00020000 "0:CDT_1" mtd14: 00080000 00020000 "0:APPSBLENV" mtd15: 00100000 00020000 "0:APPSBL" mtd16: 00100000 00020000 "0:APPSBL_1" mtd17: 00080000 00020000 "0:ART" mtd18: 00040000 00020000 "u_env" mtd19: 00020000 00020000 "s_env" mtd20: 00020000 00020000 "devinfo" mtd21: 09600000 00020000 "kernel" mtd22: 09000000 00020000 "rootfs" mtd23: 09600000 00020000 "alt_kernel" mtd24: 09000000 00020000 "alt_rootfs" mtd25: 00200000 00020000 "sysdiag" mtd26: 00080000 00020000 "0:ETHPHYFW" mtd27: 0b800000 00020000 "syscfg" mtd28: 00900000 00020000 "0:WIFIFW"
OpenWrt Firmware
root@OpenWrt:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00040000 "0:sbl1" mtd1: 00100000 00040000 "0:mibib" mtd2: 00080000 00040000 "0:bootconfig" mtd3: 00080000 00040000 "0:bootconfig1" mtd4: 00300000 00040000 "0:qsee" mtd5: 00300000 00040000 "0:qsee_1" mtd6: 00080000 00040000 "0:devcfg" mtd7: 00080000 00040000 "0:devcfg_1" mtd8: 00080000 00040000 "0:apdp" mtd9: 00080000 00040000 "0:apdp_1" mtd10: 00080000 00040000 "0:rpm" mtd11: 00080000 00040000 "0:rpm_1" mtd12: 00080000 00040000 "0:cdt" mtd13: 00080000 00040000 "0:cdt_1" mtd14: 00080000 00040000 "0:appsblenv" mtd15: 00100000 00040000 "0:appsbl" mtd16: 00100000 00040000 "0:appsbl_1" mtd17: 00080000 00040000 "0:art" mtd18: 00100000 00040000 "u_env" mtd19: 00100000 00040000 "s_env" mtd20: 00040000 00040000 "devinfo" mtd21: 0af40000 00040000 "kernel" mtd22: 0a740000 00040000 "rootfs" mtd23: 0af40000 00040000 "alt_kernel" mtd24: 0a740000 00040000 "alt_rootfs" mtd25: 00400000 00040000 "sysdiag" mtd26: 00080000 00040000 "0:ethphyfw" mtd27: 079c0000 00040000 "syscfg" mtd28: 00400000 00040000 "secured_store" mtd29: 01900000 00040000 "0:wififw" mtd30: 16180000 00040000 "app2_data" mtd31: 09280000 00040000 "app2"
OEM easy installation
None at the current time of writing this (08/01/2024)
OEM installation using the TFTP method
Specific values needed for tftp
Enter values for “FILL-IN” below
| Bootloader tftp server IPv4 address | FILL-IN |
|---|---|
| Bootloader MAC address (special) | FILL-IN |
| Firmware tftp image | Latest OpenWrt release (NOTE: Name must contain “tftp”) |
| TFTP transfer window | FILL-IN seconds |
| TFTP window start | approximately FILL-IN seconds after power on |
| TFTP client required IP address | FILL-IN |
Upgrading OpenWrt
LuCI Web Upgrade Process
- Browse to
http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/LuCI Upgrade URL - Upload sysupgrade.bin file for sysupgrade to LuCI
- Wait for reboot
Terminal Upgrade Process
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:
sysupgrademtd
Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
sysupgrade
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/qualcommax/ipq807x/xxx.bin sysupgrade /tmp/xxx.bin
mtd
If sysupgrade does not support this router, use mtd.
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/qualcommax/ipq807x/xxx.bin 1. First Check booted partition fw_printenv -n boot_part 2. Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
Debricking
USB Recovery
Recovery boot is useful for testing new kernels or when something bad happens to the firmware. First, prepare the flash drive:
wget -c https://downloads.openwrt.org/snapshots/targets/qualcommax/ipq807x/openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb sudo dd if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX
Where X needs to be changed for your disk letter. The
lsblk
command prints info about all available disks in the system and it's easy to detect the target drive by the size.
The following environment variables should be edited on the router:
fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr' fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
Turn off the router, plug in the flash drive, then turn the router back on. When you need to boot from NAND as usual, unplug the flash drive and reboot.
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
The Linksys MX4300 has the following buttons:
| BUTTON | Event |
|---|---|
| Reset | reset |
| WPS Button | wps |
Hardware
Info
Photos
Opening the case
→ Warranty
To Open the case you will need a flat pry too and a Philips screwdriver
First use the pry tool to remove the top grille be very gentle and careful as its quite a soft plastic (As seen in the below image)
If you have a thin and a long enough flat screwdriver that fits in the holes you can skip this step and move on to the next step
Once the grille has been remove you'll see 4 screws that you'll need to remove
At this point the white casing should just slide off and you'll have access to the PCB
Main PCB:
Similar to MX4200 V1 PCB
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
MX4200 v1 Serial Below:
MX4200 v2 Serial Below:
As depicted on the picture above:
| Serial connection parameters for Linksys MX4300 | 115200, 8N1, 3.3V |
|---|
Bootlogs
OEM bootlog
COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE
OpenWrt bootlog
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.6.71 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28589-54463f1e2e) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Jan 13 14:28:14 2025 [ 0.000000] OF: fdt: Input kernel commad line: init=/sbin/init rootfstype=squashfs ubi.mtd=22,2048 ubi.block=0,0 root=/dev/ubiblock0_0 rootwait ro [ 0.000000] OF: fdt: Replace kernel command line with bootargs-replace-1 [ 0.000000] OF: fdt: Kernel command line after replacement: init=/sbin/init rootfstype=squashfs ubi.mtd=22,4096 ubi.block=0,0 root=/dev/ubiblock0_0 rootwait ro [ 0.000000] Machine model: Linksys MX4300 [ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000 [ 0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fffff (2048 KiB) nomap non-reusable tzapp@4a400000 [ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable bootloader@4a600000 [ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable sbl@4aa00000 [ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 KiB) nomap non-reusable smem@4ab00000 [ 0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 KiB) nomap non-reusable memory@4ac00000 [ 0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 KiB) nomap non-reusable wcnss@4b000000 [ 0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffffff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000 [ 0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fffff (1024 KiB) nomap non-reusable m3_dump@51000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff] [ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff] [ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff] [ 0.000000] node 0: [mem 0x0000000051100000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 18 pages/cpu s36136 r8192 d29400 u73728 [ 0.000000] pcpu-alloc: s36136 r8192 d29400 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=22,4096 ubi.block=0,0 root=/dev/ubiblock0_0 rootwait ro [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 2MB [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x00000000bd600000-0x00000000bd800000] (2MB) [ 0.000000] Memory: 1912624K/2097152K available (8576K kernel code, 920K rwdata, 2576K rodata, 1600K init, 295K bss, 184528K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479] [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000109] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000121] pid_max: default: 32768 minimum: 301 [ 0.005141] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.005158] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.009460] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.009689] rcu: Hierarchical SRCU implementation. [ 0.009693] rcu: Max phase no-delay instances is 1000. [ 0.010644] smp: Bringing up secondary CPUs ... [ 0.011321] Detected VIPT I-cache on CPU1 [ 0.011427] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.012106] Detected VIPT I-cache on CPU2 [ 0.012176] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.012834] Detected VIPT I-cache on CPU3 [ 0.012901] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.012972] smp: Brought up 1 node, 4 CPUs [ 0.012980] SMP: Total of 4 processors activated. [ 0.012985] CPU features: detected: 32-bit EL0 Support [ 0.012990] CPU features: detected: CRC32 instructions [ 0.013053] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.013060] CPU: All CPU(s) started at EL1 [ 0.013063] alternatives: applying system-wide alternatives [ 0.024554] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.024579] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.026315] pinctrl core: initialized pinctrl subsystem [ 0.028361] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.028978] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.029034] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.029086] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.029510] thermal_sys: Registered thermal governor 'step_wise' [ 0.029569] cpuidle: using governor menu [ 0.029807] ASID allocator initialised with 65536 entries [ 0.056303] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 0.058230] Modules: 29232 pages in range for non-PLT usage [ 0.058237] Modules: 520752 pages in range for PLT usage [ 0.061797] SCSI subsystem initialized [ 0.062006] usbcore: registered new interface driver usbfs [ 0.062041] usbcore: registered new interface driver hub [ 0.062091] usbcore: registered new device driver usb [ 0.062536] qcom_scm: convention: smc arm 64 [ 0.064322] clocksource: Switched to clocksource arch_sys_counter [ 0.068255] NET: Registered PF_INET protocol family [ 0.068444] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.072227] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.072260] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.072276] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.072437] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 0.072982] TCP: Hash tables configured (established 16384 bind 16384) [ 0.073537] MPTCP token hash table entries: 2048 (order: 3, 49152 bytes, linear) [ 0.073751] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.073817] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.074431] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.074474] PCI: CLS 0 bytes, default 64 [ 0.076169] workingset: timestamp_bits=46 max_order=19 bucket_order=0 [ 0.076950] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.076958] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.080819] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.083265] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator [ 0.083448] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator [ 0.084736] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator [ 0.084868] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator [ 0.084924] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator [ 0.085137] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy [ 0.093474] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.097477] msm_serial 78b3000.serial: msm_serial: detected port #0 [ 0.097532] msm_serial 78b3000.serial: uartclk = 3686400 [ 0.097884] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 20, base_baud = 230400) is a MSM [ 0.097920] msm_serial: console setup on port #0 [ 0.097961] printk: console [ttyMSM0] enabled [ 0.913008] msm_serial: driver initialized [ 0.922447] loop: module loaded [ 0.923877] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa3 [ 0.924439] nand: Micron MT29F8G08ABBCAH4 [ 0.930996] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 [ 0.935317] 32 fixed-partitions partitions found on MTD device qcom_nand.0 [ 0.942735] Creating 32 MTD partitions on “qcom_nand.0”: [ 0.949424] 0x000000000000-0x000000100000 : “0:sbl1” [ 0.955988] 0x000000100000-0x000000200000 : “0:mibib” [ 0.960746] 0x000000200000-0x000000280000 : “0:bootconfig” [ 0.965598] 0x000000280000-0x000000300000 : “0:bootconfig1” [ 0.970853] 0x000000300000-0x000000600000 : “0:qsee” [ 0.977520] 0x000000600000-0x000000900000 : “0:qsee_1” [ 0.982496] 0x000000900000-0x000000980000 : “0:devcfg” [ 0.986621] 0x000000980000-0x000000a00000 : “0:devcfg_1” [ 0.991600] 0x000000a00000-0x000000a80000 : “0:apdp” [ 0.997129] 0x000000a80000-0x000000b00000 : “0:apdp_1” [ 1.002008] 0x000000b00000-0x000000b80000 : “0:rpm” [ 1.007028] 0x000000b80000-0x000000c00000 : “0:rpm_1” [ 1.011769] 0x000000c00000-0x000000c80000 : “0:cdt” [ 1.016992] 0x000000c80000-0x000000d00000 : “0:cdt_1” [ 1.021626] 0x000000d00000-0x000000d80000 : “0:appsblenv” [ 1.026919] 0x000000d80000-0x000000e80000 : “0:appsbl” [ 1.032418] 0x000000e80000-0x000000f80000 : “0:appsbl_1” [ 1.037475] 0x000000f80000-0x000001000000 : “0:art” [ 1.042747] 0x000001000000-0x000001100000 : “u_env” [ 1.047553] 0x000001100000-0x000001200000 : “s_env” [ 1.052381] 0x000001200000-0x000001240000 : “devinfo” [ 1.057051] 0x000001240000-0x00000c180000 : “kernel” [ 1.130755] 0x000001a40000-0x00000c180000 : “rootfs” [ 1.196866] mtd: setting mtd22 (rootfs) as root device [ 1.197361] mtdsplit: no squashfs found in “rootfs” [ 1.200913] 0x00000c180000-0x0000170c0000 : “alt_kernel” [ 1.274855] 0x00000c980000-0x0000170c0000 : “alt_rootfs” [ 1.340879] 0x0000170c0000-0x0000174c0000 : “sysdiag” [ 1.342990] 0x0000174c0000-0x000017540000 : “0:ethphyfw” [ 1.345674] 0x000017540000-0x00001ef00000 : “syscfg” [ 1.398560] 0x00001ef00000-0x00001f300000 : “secured_store” [ 1.400694] 0x00001f300000-0x000020c00000 : “0:wififw” [ 1.413321] 0x000020c00000-0x000036d80000 : “app2_data” [ 1.552484] 0x000036d80000-0x000040000000 : “app2” [ 1.621992] spmi spmi-0: PMIC arbiter version v2 (0x20010000) [ 1.640983] i2c_dev: i2c /dev entries driver [ 1.648432] sdhci: Secure Digital Host Controller Interface driver [ 1.648475] sdhci: Copyright© Pierre Ossman [ 1.653511] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.659895] remoteproc remoteproc0: releasing cd00000.q6v5_wcss [ 1.666464] NET: Registered PF_INET6 protocol family [ 1.670334] Segment Routing with IPv6 [ 1.674596] In-situ OAM (IOAM) with IPv6 [ 1.678158] NET: Registered PF_PACKET protocol family [ 1.682130] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.687990] 8021q: 802.1Q VLAN Support v1.8 [ 1.728865] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 1.729244] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 [ 1.735023] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1 [ 1.741591] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 [ 1.749375] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable [ 1.756803] cpr3_mem_acc_init: apc: not using memory accelerator regulator [ 1.765921] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV [ 1.772843] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 816000 uV [ 1.782853] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 872000 uV [ 1.792659] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 960000 uV [ 1.802518] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 722, quot_offset[ 7]= 0 [ 1.812280] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 936, quot_offset[ 7]= 210 [ 1.823136] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1032, quot_offset[ 7]= 95 [ 1.834069] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1192, quot_offset[ 7]= 160 [ 1.845246] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop [ 1.848034] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz [ 1.864856] remoteproc remoteproc0: cd00000.q6v5_wcss is available [ 1.873728] ubi0: attaching mtd22 [ 2.164324] random: crng init done [ 2.505338] ubi0: scanning is finished [ 2.511409] ubi0: attached mtd22 (name “rootfs”, size 167 MiB) [ 2.511446] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes [ 2.516151] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 [ 2.522996] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192 [ 2.529861] ubi0: good PEBs: 668, bad PEBs: 1, corrupted PEBs: 0 [ 2.536630] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 2.542877] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1736778494 [ 2.549935] ubi0: available PEBs: 0, total reserved PEBs: 668, PEBs reserved for bad PEB handling: 79 [ 2.559214] ubi0: background thread “ubi_bgt0d” started, PID 718 [ 2.559721] block ubiblock0_0: created from ubi0:0(rootfs) [ 2.574502] clk: Disabling unused clocks [ 2.583448] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 2.584009] Freeing unused kernel memory: 1600K [ 2.589736] Run /sbin/init as init process [ 2.593902] with arguments: [ 2.593904] /sbin/init [ 2.593907] with environment: [ 2.593909] HOME=/ [ 2.593912] TERM=linux [ 2.766896] init: Console is alive [ 2.767049] init: - watchdog - [ 3.316195] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.348699] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 3.390076] ssdk_dt_parse_interrupt[941]:INFO:intr-gpio does not exist [ 3.688408] adpt_hppe_uniphy_mode_set[1398]:INFO:ssdk doesn't support mode:0 in uniphy:0 on platform! [ 3.688576] regi_init[2525]:INFO:Initializing HPPE Done!! [ 3.696708] regi_init[2574]:INFO:qca-ssdk module init succeeded! [ 3.704661] EDMA ver 1 hw init [ 3.708294] EDMA HW Reset completed succesfully [ 3.710967] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7) [ 3.715379] RxDesc:1 (15-15) RxFill:1 (7-7) [ 3.720961] dp2: ppe offload disabled: 0 for macid 2 [ 3.724756] dp2: Switch attached to macid 2 status: 0 [ 3.915048] Qualcomm QCA8075 90000.mdio-1:01: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:01, irq=POLL) [ 3.916029] dp3: ppe offload disabled: 0 for macid 3 [ 3.923942] dp3: Switch attached to macid 3 status: 0 [ 4.004670] Qualcomm QCA8075 90000.mdio-1:02: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:02, irq=POLL) [ 4.005628] GMAC4(ffffff80041dd940) Invalid MAC@ - using 06:05:ec:db:bb:88 [ 4.013566] dp4: ppe offload disabled: 0 for macid 4 [ 4.020446] dp4: Switch attached to macid 4 status: 0 [ 4.094681] Qualcomm QCA8075 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL) [ 4.095655] GMAC5(ffffff8003a7b940) Invalid MAC@ - using 86:77:0b:7a:b8:82 [ 4.103574] dp5: ppe offload disabled: 0 for macid 5 [ 4.110455] dp5: Switch attached to macid 5 status: 0 [ 4.194695] Qualcomm QCA8075 90000.mdio-1:04: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:04, irq=POLL) [ 4.195579] [ 4.203586] * NSS Data Plane driver [ 4.210112] [ 4.227094] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.227147] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 4.231616] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010 [ 4.239123] xhci-hcd xhci-hcd.1.auto: irq 38, io mem 0x08a00000 [ 4.248541] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.254326] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 4.259873] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 4.268029] hub 1-0:1.0: USB hub found [ 4.274054] hub 1-0:1.0: 1 port detected [ 4.278255] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.282203] hub 2-0:1.0: USB hub found [ 4.290040] hub 2-0:1.0: 1 port detected [ 4.296855] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.300178] init: - preinit - [ 4.649999] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead. [ 4.697611] mtdblock: MTD device 'u_env' is NAND, please consider using UBI block devices instead. [ 4.864111] mtdblock: MTD device 'u_env' is NAND, please consider using UBI block devices instead. [ 8.324484] nss-dp 3a001800.dp5 lan1: PHY Link up speed: 1000 [ 9.462049] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 9.462187] UBIFS (ubi0:1): background thread “ubifs_bgt0_1” started, PID 1011 [ 9.522201] UBIFS (ubi0:1): recovery needed [ 9.629285] UBIFS (ubi0:1): recovery completed [ 9.629407] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name “rootfs_data” [ 9.632631] UBIFS (ubi0:1): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 9.640557] UBIFS (ubi0:1): FS size: 138657792 bytes (132 MiB, 546 LEBs), max 556 LEBs, journal size 6856704 bytes (6 MiB, 27 LEBs) [ 9.650452] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 9.662064] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID F37D681C-8C3F-4CA7-B9AA-612BC390C770, small LPT model [ 9.676603] mount_root: switching to ubifs overlay [ 9.685975] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 9.692277] urandom-seed: Seeding with /etc/urandom.seed [ 9.761020] nss-dp 3a001800.dp5 lan1: PHY Link is down [ 9.769855] procd: - early - [ 9.769964] procd: - watchdog - [ 10.329132] procd: - watchdog - [ 10.332030] procd: - ubus - [ 10.391182] procd: - init - [ 10.764686] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.889276] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a [ 10.889319] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2 [ 10.901405] NET: Registered PF_QIPCRTR protocol family [ 10.979779] PPP generic driver version 2.4.2 [ 10.980694] NET: Registered PF_PPPOX protocol family [ 10.993348] ath11k c000000.wifi: ipq8074 hw2.0 [ 10.993384] ath11k c000000.wifi: FW memory mode: 0 [ 11.024388] urngd: v1.0.2 started. [ 11.035198] remoteproc remoteproc0: powering up cd00000.q6v5_wcss [ 11.035618] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 12.188020] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up [ 12.231996] ath11k c000000.wifi: qmi ignore invalid mem req type 3 [ 12.239466] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff [ 12.239503] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1 [ 12.397025] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcss [ 12.397069] remoteproc remoteproc0: powering up cd00000.q6v5_wcss [ 12.403235] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 12.755810] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up [ 12.759019] kmodloader: done loading kernel modules from /etc/modules.d/* [ 12.799738] ath11k c000000.wifi: qmi ignore invalid mem req type 3 [ 12.807247] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff [ 12.807297] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1 [ 13.194737] ath11k c000000.wifi: htt event 48 not handled [ 15.551629] br-lan: port 1(lan1) entered blocking state [ 15.551673] br-lan: port 1(lan1) entered disabled state [ 15.555861] nss-dp 3a001800.dp5 lan1: entered allmulticast mode [ 15.561176] nss-dp 3a001800.dp5 lan1: entered promiscuous mode [ 15.574885] br-lan: port 2(lan2) entered blocking state [ 15.574932] br-lan: port 2(lan2) entered disabled state [ 15.578972] nss-dp 3a001600.dp4 lan2: entered allmulticast mode [ 15.584399] nss-dp 3a001600.dp4 lan2: entered promiscuous mode [ 15.593683] br-lan: port 3(lan3) entered blocking state [ 15.596054] br-lan: port 3(lan3) entered disabled state [ 15.601129] nss-dp 3a001400.dp3 lan3: entered allmulticast mode [ 15.606558] nss-dp 3a001400.dp3 lan3: entered promiscuous mode [ 18.644474] nss-dp 3a001800.dp5 lan1: PHY Link up speed: 1000 [ 18.644534] br-lan: port 1(lan1) entered blocking state [ 18.649217] br-lan: port 1(lan1) entered forwarding state [ 18.734583] nss-dp 3a001200.dp2 wan: PHY Link up speed: 1000 [ 33.124363] l11: disabling