User Tools

Site Tools


toh:linksys:linksys_ea7500_v1

Linksys EA7500 V1

EA7500V1 Linksys EA7500 V1 is Qualcomm IPQ8064 2-core router. It have bgn+ac wifi and two USB ports (2.0 and 3.0). Router have 4 GbE LAN ports and 1 GbE WAN port.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
EA7500V1Qualcomm IPQ80641400128NAND256Qualcomm Atheros QCA9982, Qualcomm Atheros QCA9983b/g/na/n/ac-5-1x 2.0, 1x 3.0

Installation

Flash Layout

Layer0 raw flash, 128 MiB
Layer1 mtd0-9
various systems
U-Boot
bootloader config
mtd13
firmware 1st copy
40 MiB
mtd15
firmware second copy
40 MiB
mtd17-18
Linksys configuration
Layer2 various
12800 KiB
mtd8
ART
1280 KiB
various
1024 KiB
mtd10
u_env
256 KiB
mtd11
s_env
256 KiB
mtd12
devinfo
256 KiB
kernel1
3 MiB
mtd14
rootfs1
37 MiB
kernel2
3 MiB
mtd16
rootfs2
37 MiB
mtd17
sysdiag
1 MiB
mtd18
syscfg
around 32 MiB
Layer3 squashfs
around 2 MiB
ubifs
around 35 MiB
squashfs
around 2 MiB
ubifs
around 35 MiB

OEM easy installation

Note: Some devices won't flash via web gui.

Installation:

  • Newer stock images doesn't allow to install custom firmware.
  • Please downgrade software to 1.1.2 version. Official firmware: Link
  • Do it two times to downgrade all stored images.
  • Apply factory image via web-gui.

OEM installation using the TFTP + serial method

generic.flashing.tftp

Serial + TFTP method:

  • downgrade to 1.1.2 two times. Official firmware: Link
  • connect ehternet and serial cable
  • set ip address of tftp server to 192.168.1.254
  • put openwrt factory image to tftp folder and rename it to macan.bin
  • stop device while booting in u-boot
  • run command: “run flashimg”
  • run command: “setenv boot_part 1”
  • run command “saveenv”
  • reset

Revert to stock

Back to stock:

  • Please use old non-gpg image like this 1.1.2: Link
  • ssh to router and copy image to tmp
  • use sysupgrade -n -F

Upgrading OpenWrt

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/targets/ipq806x/generic/openwrt-ipq806x-generic-linksys_ea7500-v1-squashfs-sysupgrade.bin
sysupgrade /tmp/openwrt-ipq806x-generic-linksys_ea7500-v1-squashfs-sysupgrade.bin

Debricking

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
eth1.1 LAN ports (1 to 4) None
eth0.2 WAN port DHCP
wlan0 & wlan1 WiFi Disabled

Switch Ports (for VLANs)

Port Switch port
Internet (WAN) 1
LAN 1 2
LAN 2 3
LAN 3 4
LAN 4 5
ETH0 0
ETH1 6

Buttons

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The Linksys EA7500 has the following buttons:

BUTTON Event
Reset reset
WPS wps

Hardware

Info

General
Brand Linksys
Model EA7500
Versions V1
Device Type WiFi Router
Availability Available 2020
Comments - general
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=20c7abd4b7b9b4203b6858136b2c811b6dbd8dae
Supported Since Release
Supported Current Release snapshot
Unsupported
Hardware
Bootloader U-Boot
Target ipq806x
System-On-Chip
CPU MHz 1400
Flash MB 128NAND
RAM MB 256
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
Switch Qualcomm Atheros QCA8337
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware Qualcomm Atheros QCA9982, Qualcomm Atheros QCA9983
Detachable Antennas 3
Comments - WLAN
Interfaces
USB ports 1x 2.0, 1x 3.0
SATA ports -
Serial Yes
JTAG No
Comments - USB & SATA ports
Misc
LED count 1
Button count 2
Power supply 12 VDC, 3.5 A
Links
Forum Topic URL
WikiDevi URL https://wikidevi.wi-cat.ru/Linksys_EA7500
OEM device homepage URL https://www.linksys.com/us/p/P-EA7500/
Firmware OEM Stock URL https://www.linksys.com/gb/support-article?articleNum=208638
Firmware OpenWrt Install URL
Firmware OpenWrt Upgrade URL
Edit the underlying data View/Edit data

Photos

Top:
Top

Back:
Back

Backside label:
Backside label

Opening the case

Note: This will void your warranty!

Unscrew 4 screws under bottom.

Main PCB:
PCB Top PCB Bottom

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

UART connector

Serial connector JM1(3V3 logic):

Pin Function
1 3V3
2 TX
3 RX
4 -
5 GND

Some componnents may be unsoldered. To use uart 3V3-logic is required to mount:

Componnent Value
RM327 3KOhm 0201 resistor
RM328 3KOhm 0201 resistor
QA5 N-FET transistor, eg. SI2312
QA6 N-FET transistor, eg. SI2312

It is possible to use uart without those components but with 1V8 LOGIC:

UART 1V8 Pads

Serial connection parameters
for Linksys EA7500 V1
115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootloader mods

Hardware mods

None so far.

Bootlogs

OEM bootlog

U-Boot .07 [Standard IPQ806X.LN,r40331] (Nov 05 2015 - 14:44:22) CBT U-Boot ver: 1.1.4 smem ram ptable found: ver: 0 len: 5 DRAM: 235 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 00:06:3b:01:41:00 , eth1 Updating boot_count ... done Hit any key to stop autoboot: 0 MMC Device 0 not found MMC Device 0 not found Loading from nand0, offset 0xf80000 Image Name: Linux-3.4.103 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1897480 Bytes = 1.8 MiB Load Address: 41508000 Entry Point: 41508000 Automatic boot of image at addr 0x44000000 ... Image Name: Linux-3.4.103 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1897480 Bytes = 1.8 MiB Load Address: 41508000 Entry Point: 41508000 Verifying Checksum ... OK Loading Kernel Image ... OK OK mtdids not defined, no default present info: "mtdparts" not set Using machid 0x1260 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.103 (root@build-vm) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Thu Feb 15 17:25:15 PST 2018 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine: Linksys EA7500 WiFi Router. [ 0.000000] msm_reserve_memory: 0x44600000, 0x200000 [ 0.000000] memory pool 3 (start 4fc00000 size 400000) initialized [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] smem_find(137, 80): wrong size 72 [ 0.000000] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536 [ 0.000000] accessory_chip=0 hw_plat_subtype=0 [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0a4b000 s11072 r8192 d13504 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 58154 [ 0.000000] Kernel command line: console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs ubi.mtd=14,2048 ubi.block=0,0 root=/dev/ubiblock0_0 rootwait ro [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 49MB 180MB = 229MB total [ 0.000000] Memory: 223660k/229804k available, 10836k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xcf000000 - 0xff000000 ( 768 MB) [ 0.000000] lowmem : 0xc0000000 - 0xceb00000 ( 235 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0519000 (5188 kB) [ 0.000000] .init : 0xc0600000 - 0xc0702b40 (1035 kB) [ 0.000000] .data : 0xc0704000 - 0xc07a1160 ( 629 kB) [ 0.000000] .bss : 0xc07a1184 - 0xc0849e4c ( 676 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:1689 [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 31240ns, wraps every 134175798ms [ 0.000000] Console: colour dummy device 80x30 [ 0.150421] Calibrating delay using timer specific routine.. 12.55 BogoMIPS (lpj=62799) [ 0.150452] pid_max: default: 32768 minimum: 301 [ 0.150921] Mount-cache hash table entries: 512 [ 0.152389] CPU: Testing write buffer coherency: ok [ 0.152608] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152639] hw perfevents: enabled with ARMv7 Krait PMU driver, 5 counters available [ 0.152764] Setting up static identity map for 0x418cbd80 - 0x418cbe08 [ 0.155076] CPU1: Booted secondary processor [ 0.155139] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.155232] Brought up 2 CPUs [ 0.155263] SMP: Total of 2 processors activated (25.11 BogoMIPS). [ 0.171571] dummy: [ 0.172258] NET: Registered protocol family 16 [ 0.173102] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver [ 0.175413] meminfo_init: smem ram ptable found: ver: 0 len: 5 [ 0.175445] Found 1 memory banks grouped into 8 memory regions [ 0.175757] gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio [ 0.176538] smem_find(137, 80): wrong size 72 [ 0.176569] socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536 [ 0.176569] accessory_chip=0 hw_plat_subtype=0 [ 0.176632] msm_rpm_init: RPM firmware 3.0.16777342 [ 0.184442] clk_tbl_nss - loaded [ 0.211184] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.211184] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.211621] msm_dmov_memcpy_init: Success [ 0.218712] sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20 [ 0.218744] sps:BAM 0x12244000 is registered. [ 0.218994] sps:sps is ready. [ 0.260855] msm_pcie_setup: link initialized [ 0.261230] PCI host bridge to bus 0000:00 [ 0.261262] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fefffff] [ 0.261793] PCI: bus0: Fast back to back transfers disabled [ 0.261793] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.262605] PCI: bus1: Fast back to back transfers disabled [ 0.300968] msm_pcie_setup: link initialized [ 0.301312] PCI host bridge to bus 0000:02 [ 0.301343] pci_bus 0000:02: root bus resource [mem 0x2e000000-0x31efffff] [ 0.301811] PCI: bus2: Fast back to back transfers disabled [ 0.301811] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.302530] PCI: bus3: Fast back to back transfers disabled [ 0.421305] msm_pcie_setup: link initialization failed [ 0.421524] pci 0000:02:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.421555] pci 0000:03:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.421587] pci 0000:02:00.0: PCI bridge to [bus 03-03] [ 0.421618] pci 0000:02:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.421680] PCI: enabling device 0000:02:00.0 (0140 -> 0143) [ 0.421743] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.421774] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.421805] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 0.421836] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.421868] PCI: enabling device 0000:00:00.0 (0140 -> 0143) [ 0.448391] bio: create slab <bio-0> at 0 [ 0.449953] SCSI subsystem initialized [ 0.451827] spi_qsd spi_qsd.5: master is unqueued, this is deprecated [ 0.454170] spi_qsd spi_qsd.6: master is unqueued, this is deprecated [ 0.458481] Switching to clocksource gp_timer [ 0.480537] NET: Registered protocol family 2 [ 0.490253] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.490877] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.490971] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.491065] TCP: Hash tables configured (established 8192 bind 8192) [ 0.491096] TCP: reno registered [ 0.491096] UDP hash table entries: 128 (order: 0, 4096 bytes) [ 0.491127] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) [ 0.491565] NET: Registered protocol family 1 [ 0.492970] Detected 5 counters on the L2CC PMU. [ 0.494001] smd: register irq failed on wcnss_a11 [ 0.494033] smd: deregistering IRQs [ 0.494064] SMD: smd_core_platform_init() failed [ 0.494814] Partition(from smem) SBL1 -- Offset:0 Size:2 [ 0.494845] Partition(from smem) MIBIB -- Offset:2 Size:a [ 0.494845] Partition(from smem) SBL2 -- Offset:c Size:a [ 0.494876] Partition(from smem) SBL3 -- Offset:16 Size:14 [ 0.494876] Partition(from smem) DDRCONFIG -- Offset:2a Size:9 [ 0.494907] Partition(from smem) SSD -- Offset:33 Size:9 [ 0.494907] Partition(from smem) TZ -- Offset:3c Size:14 [ 0.494939] Partition(from smem) RPM -- Offset:50 Size:14 [ 0.494970] Partition(from smem) ART -- Offset:64 Size:a [ 0.494970] Partition(from smem) APPSBL -- Offset:6e Size:8 [ 0.495001] get_nand_partitions: partition name=rootfs found. [ 0.495001] Overlaying Olympus partition [ 0.495032] Olympus partition u_env -- Offset:76 Size:2 [ 0.495032] Olympus partition s_env -- Offset:78 Size:2 [ 0.495032] Olympus partition devinfo -- Offset:7a Size:2 [ 0.495064] Olympus partition kernel -- Offset:7c Size:140 [ 0.495064] Olympus partition rootfs -- Offset:94 Size:128 [ 0.495064] Olympus partition alt_kernel -- Offset:1bc Size:140 [ 0.495095] Olympus partition alt_rootfs -- Offset:1d4 Size:128 [ 0.495095] Olympus partition sysdiag -- Offset:2fc Size:8 [ 0.495095] Olympus partition syscfg -- Offset:304 Size:0 [ 0.495126] get_bootconfig_partition: magic not found [ 0.508653] acpuclk-ipq806x acpuclk-ipq806x: SPEED BIN: 0 [ 0.508684] acpuclk-ipq806x acpuclk-ipq806x: ACPU PVS: 1 [ 0.515338] acpuclk-ipq806x acpuclk-ipq806x: CPU0: 6 frequencies supported [ 0.515370] acpuclk-ipq806x acpuclk-ipq806x: CPU1: 6 frequencies supported [ 0.516900] msm_rpm_log_probe: OK [ 0.535363] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.535363] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.536707] msgmni has been set to 436 [ 0.538019] io scheduler noop registered [ 0.538050] io scheduler deadline registered (default) [ 0.540018] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.543392] msm_serial_hs.0: ttyHS0 at MMIO 0x12490000 (irq = 227) is a MSM HS UART [ 0.544048] msm_serial_hs module loaded [ 0.544236] msm_serial_hsl: detected port #1 [ 0.544361] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16340000 (irq = 184) is a MSM [ 0.544798] msm_serial_hsl: console setup on port #1 [ 1.353108] console [ttyHSL1] enabled [ 1.357200] msm_serial_hsl: driver initialized [ 1.366135] ahci ahci.0: forcing PORTS_IMPL to 0x1 [ 1.369978] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.377819] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 1.386941] scsi0 : ahci_platform [ 1.390034] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241 [ 1.399875] msm_nand_probe: phys addr 0x1ac00000 [ 1.403530] msm_nand_probe: dmac 0x3 [ 1.407122] msm_nand_probe: allocated dma buffer at ffdfc000, dma_addr 4f5c0000 [ 1.415807] status: e00020 [ 1.417494] nandid: 1580a101 maker 01 device a1 [ 1.422524] ONFI probe : Found an ONFI compliant device S34MS01G2 [ 1.429303] Found a supported NAND device [ 1.433114] NAND Controller ID : 0x4030 [ 1.436925] NAND Device ID : 0x1580a101 [ 1.440893] Buswidth : 8 Bits [ 1.443798] Density : 128 MByte [ 1.447016] Pagesize : 2048 Bytes [ 1.450359] Erasesize: 131072 Bytes [ 1.453764] Oobsize : 64 Bytes [ 1.456888] CFG0 Init : 0xa8d408c0 [ 1.460418] CFG1 Init : 0x0004745c [ 1.463855] ECCBUFCFG : 0x00000203 [ 1.468103] Creating 19 MTD partitions on "msm_nand": [ 1.472414] 0x000000000000-0x000000040000 : "SBL1" [ 1.480193] 0x000000040000-0x000000180000 : "MIBIB" [ 1.488191] 0x000000180000-0x0000002c0000 : "SBL2" [ 1.496126] 0x0000002c0000-0x000000540000 : "SBL3" [ 1.505810] 0x000000540000-0x000000660000 : "DDRCONFIG" [ 1.514214] 0x000000660000-0x000000780000 : "SSD" [ 1.521868] 0x000000780000-0x000000a00000 : "TZ" [ 1.531365] 0x000000a00000-0x000000c80000 : "RPM" [ 1.541049] 0x000000c80000-0x000000dc0000 : "ART" [ 1.549047] 0x000000dc0000-0x000000ec0000 : "APPSBL" [ 1.556950] 0x000000ec0000-0x000000f00000 : "u_env" [ 1.563730] 0x000000f00000-0x000000f40000 : "s_env" [ 1.570509] 0x000000f40000-0x000000f80000 : "devinfo" [ 1.577444] 0x000000f80000-0x000003780000 : "kernel" [ 1.639362] 0x000001280000-0x000003780000 : "rootfs" [ 1.697125] 0x000003780000-0x000005f80000 : "alt_kernel" [ 1.738612] ata1: SATA link down (SStatus 0 SControl 300) [ 1.763792] 0x000003a80000-0x000005f80000 : "alt_rootfs" [ 1.820024] 0x000005f80000-0x000006080000 : "sysdiag" [ 1.827772] 0x000006080000-0x000008000000 : "syscfg" [ 1.877069] UBI: attaching mtd14 to ubi0 [ 1.880037] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 1.886223] UBI: logical eraseblock size: 126976 bytes [ 1.891721] UBI: smallest flash I/O unit: 2048 [ 1.896282] UBI: VID header offset: 2048 (aligned 2048) [ 1.902311] UBI: data offset: 4096 [ 2.195220] UBI: max. sequence number: 2 [ 2.210871] UBI: attached mtd14 to ubi0 [ 2.213683] UBI: MTD device name: "rootfs" [ 2.218806] UBI: MTD device size: 37 MiB [ 2.223586] UBI: number of good PEBs: 296 [ 2.228178] UBI: number of bad PEBs: 0 [ 2.232677] UBI: number of corrupted PEBs: 0 [ 2.237050] UBI: max. allowed volumes: 128 [ 2.241674] UBI: wear-leveling threshold: 4096 [ 2.246329] UBI: number of internal volumes: 1 [ 2.250796] UBI: number of user volumes: 1 [ 2.255170] UBI: available PEBs: 0 [ 2.259731] UBI: total number of reserved PEBs: 296 [ 2.264479] UBI: number of PEBs reserved for bad PEB handling: 2 [ 2.270509] UBI: max/mean erase counter: 1/0 [ 2.274695] UBI: image sequence number: 1211679096 [ 2.279631] UBI: background thread "ubi_bgt0d" started, PID 668 [ 2.287191] UBI: ubiblock0_0 created from ubi0:0(squashfs) [ 2.323711] GPIO Bitbanged MDIO: probed [ 2.328928] PPP generic driver version 2.4.2 [ 2.332802] NET: Registered protocol family 24 [ 2.336644] PPTP driver version 0.8.5 [ 2.347141] cpuidle: using governor ladder [ 2.350827] cpuidle: using governor menu [ 2.356888] Netfilter messages via NETLINK v0.30. [ 2.360824] nf_conntrack version 0.5.0 (3494 buckets, 13976 max) [ 2.367478] ctnetlink v0.93: registering with nfnetlink. [ 2.371946] nf_conntrack_rtsp v0.7 loading [ 2.376038] ip_set: protocol 6 [ 2.379881] gre: GRE over IPv4 demultiplexor driver [ 2.383848] ip_gre: GRE over IPv4 tunneling driver [ 2.390721] nf_nat_rtsp v0.7 loading [ 2.393345] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.399281] TCP: cubic registered [ 2.403717] NET: Registered protocol family 10 [ 2.409934] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2.414839] IPv6 over IPv4 tunneling driver [ 2.422086] NET: Registered protocol family 17 [ 2.425741] Bridge firewalling registered [ 2.429803] Ebtables v2.0 registered [ 2.433239] L2TP core driver, V2.0 [ 2.436488] PPPoL2TP kernel driver, V2.0 [ 2.440424] L2TP netlink interface [ 2.443798] 8021q: 802.1Q VLAN Support v1.8 [ 2.448172] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 2.455670] Registering SWP/SWPB emulation handler [ 2.460481] clock_late_init: Removing enables held for handed-off clocks [ 2.476132] ipq_nss_get_mac_addr: MAC[0]: ff:ff:ff:ff:ff:ff [ 2.480974] ipq_nss_get_mac_addr: MAC[1]: ff:ff:ff:ff:ff:ff [ 2.486472] ipq_nss_get_mac_addr: MAC[2]: ff:ff:ff:ff:ff:ff [ 2.492064] ipq_nss_get_mac_addr: MAC[3]: ff:ff:ff:ff:ff:ff [ 2.497532] no pmic restart interrupt specified [ 2.503498] msm_cache_dump_probe: could not register L2 buffer ret = -22. [ 2.513277] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 2.520024] Freeing init memory: 1032K ********************************************************************************* _ _ __ _ __ _____ __ __ _____ | | | || \ | | / // ____]\ \ / // ____]TM | | | || \ | | / /| (___ \ V /| (____ | | | || |\ \| |\ \ \____ \ \ / \____ \ | |_____ | || | \ | \ \ ____) | | | ____) | |_______||_||_| \__| \_\[____ / |_| [_____/ (c) 2013 Belkin International, Inc. and/or its affiliates. All rights reserved. Booting macan (firmware version 1.1.4.186518) ********************************************************************************* [utopia][init] System Initialization [utopia][init] Creating /proc [utopia][init] Creating /sys [utopia][init] Creating /dev [utopia][init] Creating /tmp [utopia][init] Allocating 50M for /tmp [utopia][init] Prepairing /dev/pts [utopia][init] Setting /tmp and /var permissions [utopia][init] Starting udev.. [ 3.171290] bdutil board utility kernel module, version 1.4 [ 3.176444] bdutil board utility kernel module boardId (0) [ 3.181318] bdutil board utility LEDs kernel module, version 1.3 Attempting mount of ubifs syscfg partition UBI device number 1, total 252 LEBs (31997952 bytes, 30.5 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) [utopia][init] Using persistent syscfg data from /var/config/syscfg [utopia][init] Starting system logging [utopia][init] Starting sysevent subsystem [utopia][init] Enabling DesignWare USB3 DRD Core drivers [utopia][init] Loading QCA NSS and GMAC drivers net.netfilter.nf_conntrack_acct = 1 [utopia][init] Late loading usb drivers [utopia][init] Setting any unset system values to default [utopia][init] no persistence config file (/var/config/pstcfg) found setting up MAC addresses for all interface based on C0:56:27:39:AA:B0 NTP Servers do not need to be updated checking for interactive script start up... Updating BootCount Page[6]:3000 ... Done attempting to sync sysinfo.cgi auth credentials [utopia][init] Loading LEDS and Buttons drivers [utopia][init] Setup link to WiFi firmware and board data (EU) [utopia][init] Using EU region for WiFi firmware and board data NSS Auto scaling disabled dev.nss.ipv4cfg.ipv4_conn = 4096 dev.nss.ipv6cfg.ipv6_conn = 4096 inserting ecm.ko and fpbypass.ko for QCA Sat Mar 14 05:57:00 UTC 2020 macan login: wan, sysevent received: wan-start=NULL Lighttpd Model Base: EA7500 Generating Rainier lighttpd config Build temporary www configuration directory: TSLIIHauhEfGE wifi, sysevent received: lan-started (Sat Mar 14 06:57:05 CET 2020) wifi, service_start() Power cycle Ethernet ports. [utopia][init] Loading GMAC and WLAN drivers Registering Service myrouter._http._tcp.local port 80 Got a reply for myrouter._http._tcp.local.: Name now registered and active [utopia][init] Creating wifi devices ath0 ath1 [utopia][init] setting WiFi Red CE settings wifi, wifi_physical_start(ath0) wifi, setting obss rssi threshold (ath0) Auto channel wifi, wifi_virtual_start(ath0) wifi, wifi_user_start(ath0) wifi_user, ath0 TxBF enabled wifi, primary AP: ath0 is up wifi, wifi_guest_start(ath0) wifi, guest ath2 is disabled, do not start wifi guest wifi, wifi_physical_start(ath1) wifi, setting obss rssi threshold (ath1) wifi, wifi_virtual_start(ath1) wifi, wifi_user_start(ath1) Not ready for JNAP. Sleeping for 15 seconds... iwconfig: unknown command "5" wifi_user, ath1 TxBF enabled wifi_user, ath1 MU-MIMO enabled wifi, primary AP: ath1 is up wifi, wifi_guest_start(ath1) wifi, guest ath3 is disabled, do not start wifi guest wifi, start_hostapd() Configuration file: /tmp/hostapd-ath0.conf Configuration file: /tmp/hostapd-ath1.conf mediaserver got event: mediaserver-stop ath0: Could not connect to kernel driver Using interface ath0 with hwaddr c0:56:27:39:aa:b1 and ssid "Linksys" ath0: interface state UNINITIALIZED->ENABLED ath0: AP-ENABLED ath1: Could not connect to kernel driver Using interface ath1 with hwaddr c0:56:27:39:aa:b2 and ssid "Linksys 5" ath1: interface state UNINITIALIZED->ENABLED ath1: AP-ENABLED [utopia] Not setting ppp_clamp_mtu alljoyn service_init fastpath, sysevent received: qos_enabled Restarting nfqrecv service... net.bridge.bridge-nf-call-ip6tables = 1 net.bridge.bridge-nf-call-iptables = 1 dev.nss.general.redirect = 1 [utopia] Not setting ppp_clamp_mtu on dslite protocol udhcpc (v1.19.4) started wan, sysevent received: phylink_wan_state=up Sending discover... Sending discover... Sending select for 192.168.74.142... Lease of 192.168.74.142 obtained, lease time 43200 device_registration: Received event: wan-started Sat Mar 14 05:57:48 2020 xrac Device is not associated, exiting... data_uploader service started device_registration: Service started mediaserver got event: mediaserver-stop Starting smbd ... [fw.sh] fwup_checked_after_boot: 0 [fwupd] version: 1.1.5.190349 [fwupd] status details:"" [fw.sh] fwup_forced_update: 0 QoS auto-prioritize [info]: No networkID; skipping auto-priority update


OpenWrt bootlog

U-Boot .07 [Standard IPQ806X.LN,r40331] (Nov 05 2015 - 14:44:22) CBT U-Boot ver: 1.1.4 smem ram ptable found: ver: 0 len: 5 DRAM: 235 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is 00:06:3b:01:41:00 , eth1 Updating boot_count ... done Hit any key to stop autoboot: 0 MMC Device 0 not found MMC Device 0 not found Loading from nand0, offset 0x3780000 Image Name: ARM OpenWrt Linux-5.4.50 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2860980 Bytes = 2.7 MiB Load Address: 42208000 Entry Point: 42208000 Automatic boot of image at addr 0x44000000 ... Image Name: ARM OpenWrt Linux-5.4.50 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2860980 Bytes = 2.7 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK Loading Kernel Image ... OK OK mtdids not defined, no default present info: "mtdparts" not set Using machid 0x1260 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.50 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13739-c1794d653c)) #0 SMP Wed Jul 8 14:07:05 2020 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Linksys EA7500 V1 WiFi Router [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu s30028 r8192 d23220 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 56840 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=16 [ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 init=/sbin/init rootfstype=squashfs ubi.mtd=16,2048 ubi.block=0,0 root=/dev/ubiblock0_0 rootwait ro [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 217244K/229376K available (6111K kernel code, 193K rwdata, 1540K rodata, 1024K init, 236K bss, 12132K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x4ec with crng_init=0 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000006] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000019] Switching to timer-based delay loop, resolution 160ns [ 0.000235] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000254] pid_max: default: 32768 minimum: 301 [ 0.000458] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000476] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001533] CPU: Testing write buffer coherency: ok [ 0.002694] Setting up static identity map for 0x42300000 - 0x42300060 [ 0.002868] rcu: Hierarchical SRCU implementation. [ 0.003349] smp: Bringing up secondary CPUs ... [ 0.005234] smp: Brought up 1 node, 2 CPUs [ 0.005250] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.005261] CPU: All CPU(s) started in SVC mode. [ 0.015208] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.015361] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.015390] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.015565] pinctrl core: initialized pinctrl subsystem [ 0.016738] NET: Registered protocol family 16 [ 0.017043] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.018427] cpuidle: using governor ladder [ 0.018493] cpuidle: using governor menu [ 0.049685] usbcore: registered new interface driver usbfs [ 0.049766] usbcore: registered new interface driver hub [ 0.049850] usbcore: registered new device driver usb [ 0.049910] pps_core: LinuxPPS API ver. 1 registered [ 0.049923] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.049965] PTP clock support registered [ 0.051810] clocksource: Switched to clocksource dg_timer [ 0.052716] thermal_sys: Registered thermal governor 'step_wise' [ 0.055152] NET: Registered protocol family 2 [ 0.055886] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.055927] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.055961] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.055994] TCP: Hash tables configured (established 2048 bind 2048) [ 0.056102] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.056133] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.056372] NET: Registered protocol family 1 [ 0.056426] PCI: CLS 0 bytes, default 64 [ 0.057754] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.064650] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.064667] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.103392] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.105065] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator [ 0.105213] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.105326] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.105605] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges: [ 0.105680] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 [ 0.105718] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000 [ 0.327470] qcom-pcie 1b500000.pci: Link up [ 0.327643] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.327667] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.327687] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.327713] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.327776] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.327949] pci 0000:00:00.0: supports D1 [ 0.327967] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.331839] PCI: bus0: Fast back to back transfers disabled [ 0.332308] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000 [ 0.332689] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.333925] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.334232] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 0.338044] PCI: bus1: Fast back to back transfers disabled [ 0.338133] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.338157] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.338293] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.338317] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.339294] pcieport 0000:00:00.0: AER: enabled with IRQ 36 [ 0.339871] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator [ 0.339999] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.340140] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.340411] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges: [ 0.340481] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000 [ 0.340515] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000 [ 0.569206] qcom-pcie 1b700000.pci: Link up [ 0.569364] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.569385] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.569401] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.569456] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.569599] pci 0001:00:00.0: supports D1 [ 0.569615] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.573531] PCI: bus0: Fast back to back transfers disabled [ 0.573854] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000 [ 0.574204] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.575345] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 0.579402] PCI: bus1: Fast back to back transfers disabled [ 0.579478] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.579502] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.579626] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.579647] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.580519] pcieport 0001:00:00.0: AER: enabled with IRQ 38 [ 0.581104] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda not found, using dummy regulator [ 0.581231] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda_phy not found, using dummy regulator [ 0.581338] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda_refclk not found, using dummy regulator [ 0.581621] qcom-pcie 1b900000.pci: host bridge /soc/pci@1b900000 ranges: [ 0.581684] qcom-pcie 1b900000.pci: IO 0x35e00000..0x35efffff -> 0x35e00000 [ 0.581717] qcom-pcie 1b900000.pci: MEM 0x32000000..0x35dfffff -> 0x32000000 [ 1.732238] qcom-pcie 1b900000.pci: Phy link never came up [ 1.734279] qcom-pcie 1b900000.pci: cannot initialize host [ 1.734656] qcom-pcie: probe of 1b900000.pci failed with error -110 [ 1.736965] L2 @ QSB rate. Forcing new rate. [ 1.737190] L2 @ 384000 KHz [ 1.737369] CPU0 @ 800000 KHz [ 1.737383] CPU1 @ QSB rate. Forcing new rate. [ 1.737511] CPU1 @ 384000 KHz [ 1.741229] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 1.743533] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 1.745988] msm_serial 16340000.serial: msm_serial: detected port #0 [ 1.746044] msm_serial 16340000.serial: uartclk = 7372800 [ 1.746114] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM [ 1.746154] msm_serial: console setup on port #0 [ 2.596353] printk: console [ttyMSM0] enabled [ 2.601335] msm_serial: driver initialized [ 2.610580] loop: module loaded [ 2.612228] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 [ 2.612532] nand: AMD/Spansion S34MS01G2 [ 2.619125] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.623294] 19 fixed-partitions partitions found on MTD device qcom_nand.0 [ 2.630412] Creating 19 MTD partitions on "qcom_nand.0": [ 2.637358] 0x000000000000-0x000000040000 : "SBL1" [ 2.644288] 0x000000040000-0x000000180000 : "MIBIB" [ 2.650334] 0x000000180000-0x0000002c0000 : "SBL2" [ 2.655131] 0x0000002c0000-0x000000540000 : "SBL3" [ 2.657698] random: fast init done [ 2.666021] 0x000000540000-0x000000660000 : "DDRCONFIG" [ 2.668834] 0x000000660000-0x000000780000 : "SSD" [ 2.673112] 0x000000780000-0x000000a00000 : "TZ" [ 2.680109] 0x000000a00000-0x000000c80000 : "RPM" [ 2.685173] 0x000000c80000-0x000000dc0000 : "art" [ 2.688198] 0x000000dc0000-0x000000ec0000 : "APPSBL" [ 2.691675] 0x000000ec0000-0x000000f00000 : "u_env" [ 2.695566] 0x000000f00000-0x000000f40000 : "s_env" [ 2.700054] 0x000000f40000-0x000000f80000 : "devinfo" [ 2.705015] 0x000000f80000-0x000003780000 : "kernel1" [ 2.775411] 0x000001280000-0x000003780000 : "rootfs1" [ 2.836966] 0x000003780000-0x000005f80000 : "kernel2" [ 2.903523] 0x000003a80000-0x000005f80000 : "rootfs2" [ 2.965162] 0x000005f80000-0x000006080000 : "sysdiag" [ 2.967790] 0x000006080000-0x000008000000 : "syscfg" [ 2.993824] random: crng init done [ 3.023631] libphy: ipq8064_mdio_bus: probed [ 3.073614] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii [ 4.169585] libphy: Fixed MDIO Bus: probed [ 4.170242] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found [ 4.172677] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found [ 4.180014] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock [ 4.187051] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 4.192805] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000 [ 4.200184] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported [ 4.206070] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported [ 4.213817] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2 [ 4.221623] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported [ 4.227539] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported [ 4.234905] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors [ 4.241589] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors [ 4.249212] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled [ 4.256239] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 4.262435] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address fe:60:0a:8e:d0:43 [ 4.271902] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found [ 4.278840] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found [ 4.286259] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock [ 4.292880] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 4.298885] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000 [ 4.306448] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported [ 4.312253] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported [ 4.319889] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2 [ 4.327881] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported [ 4.333681] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported [ 4.340979] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors [ 4.347833] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors [ 4.355394] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled [ 4.362424] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 4.368509] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address fa:d1:c6:9f:3e:f1 [ 4.378244] i2c /dev entries driver [ 4.387250] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 4.388486] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 4.396314] sdhci: Secure Digital Host Controller Interface driver [ 4.402974] sdhci: Copyright(c) Pierre Ossman [ 4.409115] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.415988] NET: Registered protocol family 10 [ 4.420665] Segment Routing with IPv6 [ 4.423729] NET: Registered protocol family 17 [ 4.427330] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.434164] 8021q: 802.1Q VLAN Support v1.8 [ 4.444879] Registering SWP/SWPB emulation handler [ 4.471019] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 4.487626] s1a: supplied by regulator-dummy [ 4.487724] s1a: Bringing 0uV into 1050000-1050000uV [ 4.491256] s1b: supplied by regulator-dummy [ 4.496055] s1b: Bringing 0uV into 1050000-1050000uV [ 4.500419] s2a: supplied by regulator-dummy [ 4.505268] s2a: Bringing 0uV into 800000-800000uV [ 4.509638] s2b: supplied by regulator-dummy [ 4.514095] s2b: Bringing 0uV into 800000-800000uV [ 4.520059] Speed bin: 0 [ 4.523058] PVS bin: 1 [ 4.532784] ubi0: attaching mtd16 [ 4.803620] ubi0: scanning is finished [ 4.813929] ubi0: attached mtd16 (name "rootfs2", size 37 MiB) [ 4.813970] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.818661] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.825608] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.832466] ubi0: good PEBs: 296, bad PEBs: 0, corrupted PEBs: 0 [ 4.839146] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.845511] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1592230296 [ 4.852522] ubi0: available PEBs: 0, total reserved PEBs: 296, PEBs reserved for bad PEB handling: 20 [ 4.863486] ubi0: background thread "ubi_bgt0d" started, PID 65 [ 4.864728] block ubiblock0_0: created from ubi0:0(rootfs) [ 4.876676] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.882202] hctosys: unable to open rtc device (rtc0) [ 4.928243] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 4.930087] Freeing unused kernel memory: 1024K [ 4.974464] Run /sbin/init as init process [ 5.519211] init: Console is alive [ 5.519613] init: - watchdog - [ 6.499056] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.561388] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.564470] SCSI subsystem initialized [ 6.574423] ehci-fsl: Freescale EHCI Host controller driver [ 6.574974] ehci-platform: EHCI generic platform driver [ 6.582261] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.584435] ohci-platform: OHCI generic platform driver [ 6.592550] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found [ 6.595376] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found [ 6.601278] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found [ 6.607433] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found [ 6.615036] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found [ 6.618988] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found [ 6.624798] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found [ 6.630791] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found [ 6.643305] dwc3 11000000.dwc3: Failed to get clk 'ref': -2 [ 6.694356] dwc3 10000000.dwc3: Failed to get clk 'ref': -2 [ 6.756343] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 6.756403] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 6.760905] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 6.768433] xhci-hcd xhci-hcd.0.auto: irq 42, io mem 0x11000000 [ 6.778607] hub 1-0:1.0: USB hub found [ 6.783670] hub 1-0:1.0: 1 port detected [ 6.787596] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 6.791456] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 6.796839] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 6.804805] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.811298] hub 2-0:1.0: USB hub found [ 6.819222] hub 2-0:1.0: 1 port detected [ 6.823068] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 6.826791] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 6.832297] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 6.839658] xhci-hcd xhci-hcd.1.auto: irq 43, io mem 0x10000000 [ 6.850205] hub 3-0:1.0: USB hub found [ 6.855011] hub 3-0:1.0: 1 port detected [ 6.858921] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 6.862880] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 6.868104] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 6.875788] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.882659] hub 4-0:1.0: USB hub found [ 6.890514] hub 4-0:1.0: 1 port detected [ 6.895378] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 6.906537] init: - preinit - [ 8.843632] dwmac1000: Master AXI performs any burst length [ 8.843665] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found [ 8.848014] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 8.856172] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 8.865106] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode [ 8.872564] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 8.880639] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.088324] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 13.088484] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 162 [ 13.165565] UBIFS (ubi0:1): recovery needed [ 13.289306] UBIFS (ubi0:1): recovery completed [ 13.289398] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 13.292720] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 13.300536] UBIFS (ubi0:1): FS size: 30347264 bytes (28 MiB, 239 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs) [ 13.310488] UBIFS (ubi0:1): reserved for root: 1433376 bytes (1399 KiB) [ 13.320737] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 5B406C8C-D029-4D75-B432-FB2D5761CE47, small LPT model [ 13.335172] mount_root: switching to ubifs overlay [ 13.354414] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 13.361208] urandom-seed: Seeding with /etc/urandom.seed [ 13.418711] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down [ 13.483000] procd: - early - [ 13.483186] procd: - watchdog - [ 14.058557] procd: - watchdog - [ 14.059173] procd: - ubus - [ 14.120017] procd: - init - Please press Enter to activate this console. [ 14.447223] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.455229] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056 [ 14.455253] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb [ 14.456599] urngd: v1.0.2 started. [ 14.468596] xt_time: kernel timezone is -0000 [ 14.504131] PPP generic driver version 2.4.2 [ 14.505070] NET: Registered protocol family 24 [ 14.531920] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x40. [ 14.531981] ath10k_mac_create, priv_size: 868 hw: adb29435 hw->priv: 0941d583 [ 14.538874] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 14.546394] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 15.309767] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002 [ 15.309799] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 15.319723] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-013-d81f62d97 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 84a62744 [ 15.391169] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2 [ 16.579873] ath10k_pci 0000:01:00.0: unsupported HTC service id: 1536 [ 16.581817] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 16.585389] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 16.665276] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 16.665342] ath10k_pci 0000:01:00.0: wmi print 'free: 31048 iram: 22932 sram: 9596' [ 16.944643] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 17.052988] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x40. [ 17.053124] ath10k_mac_create, priv_size: 868 hw: 41685ca7 hw->priv: e968b28c [ 17.060408] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 17.067403] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 17.680905] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002 [ 17.680952] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 17.692828] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-013-d81f62d97 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 84a62744 [ 17.763055] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2 [ 18.947395] ath10k_pci 0001:01:00.0: unsupported HTC service id: 1536 [ 18.948216] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 18.952921] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 19.030844] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 19.030876] ath10k_pci 0001:01:00.0: wmi print 'free: 31048 iram: 22932 sram: 9596' [ 19.297633] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 19.405597] kmodloader: done loading kernel modules from /etc/modules.d/* [ 23.412606] dwmac1000: Master AXI performs any burst length [ 23.412652] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found [ 23.416996] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 23.425250] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 23.434072] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode [ 23.441146] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 23.445011] br-lan: port 1(eth1.1) entered blocking state [ 23.458404] br-lan: port 1(eth1.1) entered disabled state [ 23.463961] device eth1.1 entered promiscuous mode [ 23.469170] device eth1 entered promiscuous mode [ 23.474402] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 23.479973] br-lan: port 1(eth1.1) entered blocking state [ 23.484619] br-lan: port 1(eth1.1) entered forwarding state [ 23.504464] dwmac1000: Master AXI performs any burst length [ 23.504496] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found [ 23.508845] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 23.517056] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock [ 23.526049] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode [ 23.533240] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 23.541416] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 24.473935] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/linksys/linksys_ea7500_v1.txt · Last modified: 2020/07/15 17:57 by chkdsk