Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| toh:linksys:ea3500 [2018/02/17 19:01] – ↷ Links adapted because of a move operation | toh:linksys:ea3500 [2020/12/19 18:56] – [Tags] danitool | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Linksys EA3500 ====== | ====== Linksys EA3500 ====== | ||
| {{: | {{: | ||
| - | ===== Supported Versions ===== | ||
| - | ^ Version/ | ||
| - | | v1.0 | | ||
| - | OEM source code available at: [[http:// | + | ===== Supported Versions ===== |
| + | ---- datatable ---- | ||
| + | cols : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid | ||
| + | headers | ||
| + | align : c, | ||
| + | filter | ||
| + | filter | ||
| + | ---- | ||
| ===== Hardware Highlights ===== | ===== Hardware Highlights ===== | ||
| - | ^ SoC ^ Ram | + | ---- datatable ---- |
| - | | Marvell Feroceon 88F6282 @800 Mhz | + | cols : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, |
| - | + | header | |
| - | Manufacturer' | + | align |
| + | filter | ||
| + | filter | ||
| + | ---- | ||
| ===== Installation ===== | ===== Installation ===== | ||
| + | ---- datatable ---- | ||
| + | cols : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url | ||
| + | headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock | ||
| + | align : c,c,c | ||
| + | filter | ||
| + | ---- | ||
| - | ==Generic Information on installing OpenWRT== | + | -> [[docs:guide-user:installation: |
| - | | + | |
| - | | + | |
| - | - → [[about: | + | |
| - | ====Introduction==== | + | ==== Introduction ==== |
| - | The EA3500 is very similar to the [[toh: | + | The EA3500 is very similar to the [[toh: |
| - | Below all firmware | + | ==== Dual firmware |
| - | ==To New Users== | + | Like several other Linksys devices, the EA3500 has a dual firmware |
| - | Especially with trunk images, building yourself takes a little longer, but is usually more reliable, produces higher quality | + | |
| - | To learn more about building images, check out: | + | < |
| - | -[[ about: | + | |
| - | -[[doc:howto: | + | |
| - | -[[doc:howto:build|OpenWrt build system – Usage]] | + | |
| - | ====Versions==== | + | Current snapshot (Oct 23 2019) factory image can be flashed from stock firmware' |
| - | ===Trunk- | + | Note that the 17.01 does not have the kmod-gpio-button-hotplug package included by default, making it impossible to activate fail safe mode. It is therefore highly recommended to install kmod-gpio-button-hotplug. Later versions have this package included by default. |
| + | |||
| + | Below all firmware versions that have worked to some degree on the EA3500 are listed for historical purposes. | ||
| + | |||
| + | ==== Versions ==== | ||
| + | |||
| + | === Trunk - Deprecated (use release 17.01 or later) | ||
| * Fully supported as of [[https:// | * Fully supported as of [[https:// | ||
| * Build yourself or use snapshots | * Build yourself or use snapshots | ||
| Line 43: | Line 55: | ||
| * Upgrade from Openwrt image with '' | * Upgrade from Openwrt image with '' | ||
| - | ==Build== | + | == Build == |
| This model is identified by the board codename " | This model is identified by the board codename " | ||
| Line 59: | Line 71: | ||
| The '' | The '' | ||
| - | ==Downloadable Links== | + | === Chaos Calmer - Deprecated |
| - | + | ||
| - | Snapshots from https:// | + | |
| - | + | ||
| - | *[[https:// | + | |
| - | *[[https:// | + | |
| - | *[[https:// | + | |
| - | + | ||
| - | ===Chaos Calmer- | + | |
| * Not fully supported | * Not fully supported | ||
| * Build required | * Build required | ||
| Line 75: | Line 79: | ||
| * Issues with extroot and overlay | * Issues with extroot and overlay | ||
| - | ===Candyhouse- | + | === Candyhouse - Deprecated |
| *.ssa is basically a package of all ubifs, ramdisk, etc... It is what the factory Linksys interface uses. Based on UBIFS | *.ssa is basically a package of all ubifs, ramdisk, etc... It is what the factory Linksys interface uses. Based on UBIFS | ||
| * From Wolfteck Candyhouse Project, the first to release a working image for the EA3500/ | * From Wolfteck Candyhouse Project, the first to release a working image for the EA3500/ | ||
| Line 85: | Line 89: | ||
| - | ====TFTP Flash==== | + | ==== TFTP Flash ==== |
| - | If you don't have the web ui (bricked, | + | If you don't have the web ui (bricked, |
| - | For more info about TFTP flashing see -> [[doc:howto: | + | For more info about TFTP flashing see -> [[docs:guide-user: |
| - | [[ toh: | + | [[# |
| To connect to the router with a serial terminal such as screen or GTKterm, use the settings: | To connect to the router with a serial terminal such as screen or GTKterm, use the settings: | ||
| Line 98: | Line 102: | ||
| -Stop Bits: 1 | -Stop Bits: 1 | ||
| - | Once connected, plug in the router and break uboot by pressing any key immediately at boot. Have a tftp server running on a machine with the // | + | Once connected, plug in the router and break uboot by pressing any key immediately at boot. Have a tftp server running on a machine with the // |
| To flash the 1st boot partition, make sure //boot_part ' | To flash the 1st boot partition, make sure //boot_part ' | ||
| Line 121: | Line 125: | ||
| '' | '' | ||
| - | Again, this is not common and will likely not happen unless you have previously performed several flashes. | + | Again, this is not common and will likely not happen unless you have previously performed several flashes. |
| ==== Chaos Calmer using Serial ==== | ==== Chaos Calmer using Serial ==== | ||
| Current Chaos Calmer appears to be missing the necessary ramdisk image, so you'll need to build that in order to install using this method. | Current Chaos Calmer appears to be missing the necessary ramdisk image, so you'll need to build that in order to install using this method. | ||
| Line 290: | Line 295: | ||
| (source [https:// | (source [https:// | ||
| - | -> [[doc:howto:generic.failsafe]] | + | -> [[docs:guide-user:troubleshooting: |
| ==== Buttons ==== | ==== Buttons ==== | ||
| - | -> [[doc:howto: | + | -> [[docs:guide-user: |
| The Linksys EA3500 has two buttons. They are Reset and WPS. Here, we merely name the buttons, so we can use them in the above Howto: | The Linksys EA3500 has two buttons. They are Reset and WPS. Here, we merely name the buttons, so we can use them in the above Howto: | ||
| Line 302: | Line 307: | ||
| ===== Hardware ===== | ===== Hardware ===== | ||
| ==== Info ==== | ==== Info ==== | ||
| - | | **[[wp> | + | ^ [[wp> |
| - | | **Vendor:** | [[wp> | + | ^ Vendor |
| - | | **[[doc:techref:Bootloader]]:** | [[doc: | + | ^ [[docs:techref:bootloader]] | [[docs: |
| - | | **[[doc: | + | ^ [[docs: |
| - | | **[[doc: | + | ^ [[docs: |
| - | | **Flash size:** | 64 MiB | | + | ^ Flash size | 64 MiB | |
| - | | **Flash Chip:** | Hynix NAND 64MiB 3,3V 8-bit | | + | ^ Flash Chip | Hynix NAND 64MiB 3,3V 8-bit | |
| - | | **RAM size:** | 64 MiB | | + | ^ RAM size | 64 MiB | |
| - | | **RAM Chip:** | | | + | ^ RAM Chip |
| - | | **Wireless No1:** | Marvell 88W8366 v48 for 2Ghz | | + | ^ Wireless No1 | Marvell 88W8366 v48 for 2Ghz | |
| - | | **Wireless No2:** | Marvell 88W8366 v48 for 5Ghz | | + | ^ Wireless No2 | Marvell 88W8366 v48 for 5Ghz | |
| - | | **[[doc:hardware:Switch]]:** | Marvell 643xx (Gigabit, VLAN) | | + | ^ [[docs: |
| - | | **USB:** | Yes 1 x 2.0 | | + | ^ USB | Yes 1 x 2.0 | |
| - | | **[[doc: | + | ^ [[docs: |
| - | | **[[doc: | + | ^ [[docs: |
| ==== Photos ==== | ==== Photos ==== | ||
| Line 340: | Line 345: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| The serial port is located at J7. | The serial port is located at J7. | ||
| Line 363: | Line 368: | ||
| Below is an illustration of a standard 3.5mm minijack being used as an external serial port connection. It fits nicely in a space by the power supply input on the back. I just picked up the female connection and a male connector at Radio Shack, however much better deals can be found online. | Below is an illustration of a standard 3.5mm minijack being used as an external serial port connection. It fits nicely in a space by the power supply input on the back. I just picked up the female connection and a male connector at Radio Shack, however much better deals can be found online. | ||
| - | {{ media: | + | {{ media: |
| ==External Antennas== | ==External Antennas== | ||
| Line 369: | Line 374: | ||
| Each radio has 3 internal antennas with UFL jacks so adding some pigtails with RP-SMA jacks on the outside is straightforward. Here is the best location I found to mount them. Everything fist nicely. | Each radio has 3 internal antennas with UFL jacks so adding some pigtails with RP-SMA jacks on the outside is straightforward. Here is the best location I found to mount them. Everything fist nicely. | ||
| - | {{media: | + | {{media: |
| - | {{media: | + | {{media: |
| ==== JTAG ==== | ==== JTAG ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| J8 sure looks like a JTAG port, but it hasn't been tried. | J8 sure looks like a JTAG port, but it hasn't been tried. | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| A useful method to un-brick this router is to: | A useful method to un-brick this router is to: | ||
| Line 384: | Line 390: | ||
| 3. Repeat the top steps three times, and when the power light no longer turns off during boot up, the device should be reset to default firmware/ settings. | 3. Repeat the top steps three times, and when the power light no longer turns off during boot up, the device should be reset to default firmware/ settings. | ||
| - | Source: https:// | + | Source: |
| - | ===== Bootloader Mods ===== | ||
| - | - you could read about [[doc: | ||
| ===== Bootlogs ===== | ===== Bootlogs ===== | ||
| Line 1064: | Line 1068: | ||
| ===== Tags ===== | ===== Tags ===== | ||
| [[meta: | [[meta: | ||
| - | {{tag> | + | {{tag>kirkwood 64Flash 64RAM GigabitEthernet FastEthernet 4NIC 2WNIC 5Port USB ARM dual_firmware}} |