Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
toh:linksys:ea2700 [2015/12/05 17:56] – created CanadianJefftoh:linksys:ea2700 [2015/12/06 09:15] CanadianJeff
Line 1: Line 1:
 +====== Linksys EA2700 ======
  
 +===== Supported Versions =====
 +^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^
 +| - |  -  | - | - | - |
 +
 +===== Hardware Highlights =====
 +^ CPU ^ Ram ^ Flash ^ Network ^ Wireless ^ USB ^ Serial ^ JTag ^
 +| BCM5357@480MHz | 64MiB | 64MiB | 1+4 x 1000 M | 2.4 GHz () + 5 GHz () | No | ? | ? |
 +
 +Manufacturer's site: [[http://support.linksys.com/ea2700]]
 +
 +===== Installation =====
 +=== Recent trunk builds ===
 +
 +
 +===== Older Information =====
 +
 +
 +=== Installation without Serial ===
 +
 +There is another way to Flash your device, without using a serial connection.\\
 +These steps are to be used if you are running the factory cisco firmware.\\
 +
 +^ Filename ^ SHA1 ^
 +| FW_EA2700_1.0.14.129982.SSA | c086d3ea594eab3683f2a1882d91e5ac2a360f0d |
 +
 +Prepare:
 +  * Download older crippled linksys firmware [[http://downloads.linksys.com/downloads/firmware/FW_EA2700_1.0.14.129982.zip|Here]]
 +  * Downgrade to a crippled version of the linksys firmware (FW_EA2700_1.0.14.129982)
 +  * In the old style linksys GUI at http://192.168.1.1 you can now flash a new firmware
 +
 +==== Flash Layout ====
 +
 +The stock layout (of the 64MiB flash chip):
 +
 +^ Offset ^ Size ^ Name ^
 +
 +
 +===== HW Info (lspci) =====
 +  00:00.0 FLASH memory: Broadcom Corporation Sentry5 Chipcommon I/O Controller (rev 02)
 +  00:01.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 02)
 +  00:02.0 Ethernet controller: Broadcom Corporation BCM47xx Sentry5 USB / Ethernet Controller (rev 02)
 +  00:04.0 USB controller: Broadcom Corporation Device 471a (rev 02)
 +  00:04.1 USB controller: Broadcom Corporation Device 471a (rev 02)
 +  00:05.0 RAM memory: Broadcom Corporation Device 082e (rev 02)
 +  00:06.0 Multimedia audio controller: Broadcom Corporation BCM47xx Sentry5 iLine32 HomePNA 2.0 (rev 02)
 +  00:07.0 RAM memory: Broadcom Corporation Device 080e (rev 02)
 +
 +===== HW Info (DMESG) =====
 +  bcm_robo_enable_switch: EEE is enabled
 +  eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.89.21 (r524987)
 +  roboswitch: Probing device 'eth0'
 +  roboswitch: trying a 53125! at eth0
 +  roboswitch: found a 53125! at eth0
 +
 +===== Stock Firmware Booting =====
 +<code>
 +ÿ Decompressing...done
 +Decompressing...done
 +Found chip type AI (0x18a25357)
 +Chipc: rev 38, caps 0x90480109, chipst 0x3e512 pmurev 9, pmucaps 0x28a42a09
 +Found a Hynix NAND flash with 512B pages or 16KB blocks; total size 64MB
 +No PLL init done for chip 5357 rev 2 pmurev 9
 +si_kattach done. ccrev = 38, wd_msticks = 32
 +
 +
 +CFE version 5.119.138.2006 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
 +Build Date: Fri Feb 17 08:48:15 CST 2012 (sip@datacom)
 +Copyright (C) 2000-2008 Broadcom Corporation.
 +
 +Init Arena
 +Init Devs.
 +Boot partition size = 262144(0x40000)
 +si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0x4715
 +Found chip type AI (0x18a25357)
 +Chipc: rev 38, caps 0x90480109, chipst 0x3e512 pmurev 9, pmucaps 0x28a42a09
 +No PLL init done for chip 5357 rev 2 pmurev 9
 +et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.119.138.2006
 +CPU type 0x19749: 480MHz
 +Tot mem: 65536 KBytes
 +
 +CFE mem:    0x80700000 - 0x8086A0B0 (1482928)
 +Data:       0x80753D00 - 0x80757110 (13328)
 +BSS:        0x80757110 - 0x807680B0 (69536)
 +Heap:       0x807680B0 - 0x808680B0 (1048576)
 +Stack:      0x808680B0 - 0x8086A0B0 (8192)
 +Text:       0x80700000 - 0x80753D00 (343296)
 +Boot:       0x0086B000 - 0x008AB000
 +Reloc:      I:00000000 - D:00000000
 +
 +Boot version: v1.3.1
 +
 +Device eth0:  hwaddr 20-AA-4B-76-96-DE, ipaddr 192.168.1.1, mask 255.255.255.0
 +        gateway not set, nameserver not set
 +Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
 +Loading: Failed.
 +Could not load :: Timeout occured
 +Booting(0): boot -raw -z -addr=0x80001000 -max=0x6ff000 nflash0.os:
 +Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
 +Loading: ........ 4808837 bytes read
 +Entry at 0x80001000
 +Closing network.
 +et0: link down
 +Starting program at 0x80001000
 +Linux version 2.6.22 (root@ubuntu) (gcc version 4.2.3) #1 PREEMPT Fri Feb 17 23:08:07 PST 2012
 +CPU revision is: 00019749
 +Found a Hynix NAND flash with 512B pages or 16KB blocks; total size 64MB
 +Determined physical RAM map:
 + memory: 04000000 @ 00000000 (usable)
 +Initrd not found or empty - disabling initrd
 +Zone PFN ranges:
 +  Normal          0 ->    16384
 +  HighMem     16384 ->    16384
 +early_node_map[1] active PFN ranges
 +    0:        0 ->    16384
 +Built 1 zonelists.  Total pages: 16384
 +Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
 +Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
 +Primary data cache 32kB, 4-way, linesize 32 bytes.
 +Synthesized TLB refill handler (20 instructions).
 +Synthesized TLB load handler fastpath (32 instructions).
 +Synthesized TLB store handler fastpath (32 instructions).
 +Synthesized TLB modify handler fastpath (31 instructions).
 +PID hash table entries: 512 (order: 9, 2048 bytes)
 +CPU: BCM5357 rev 2 at 480 MHz
 +Using 240.000 MHz high precision timer.
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 59220k/65536k available (3876k kernel code, 6252k reserved, 571k data, 248k init, 0k highmem)
 +Mount-cache hash table entries: 512
 +NET: Registered protocol family 16
 +SCSI subsystem initialized
 +PCI: no core
 +PCI: no core
 +PCI: Fixing up bus 0
 +NET: Registered protocol family 2
 +Time: MIPS clocksource has been installed.
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +VFS: Disk quotas dquot_6.5.1
 +Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
 +squashfs: version 3.4 (2008/08/26) Phillip Lougher
 +NTFS driver 2.1.28 [Flags: R/W].
 +JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
 +fuse init (API version 7.8)
 +io scheduler noop registered (default)
 +HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
 +N_HDLC line discipline registered.
 +Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
 +serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
 +RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
 +loop: module loaded
 +PPP generic driver version 2.4.2
 +PPP MPPE Compression module registered
 +NET: Registered protocol family 24
 +SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
 +pflash: found no supported devices
 +Found an ST compatible serial flash with 0 64KB blocks; total size 0MB
 +sflash: found no supported devices
 +The first offset=200000, 2nd offset=1400000
 +Boot partition size = 524288(0x80000)
 +lookup_nflash_rootfs_offset: offset = 0x200000
 +nflash: squash filesystem with lzma found at block 246
 +2nd offset 1400000
 +lookup_nflash_rootfs_offset: offset = 0x1400000
 +nflash: squash filesystem with lzma found at block 1398
 +Creating 6 MTD partitions on "nflash":
 +0x00000000-0x00080000 : "boot"
 +0x00080000-0x00200000 : "nvram"
 +0x00200000-0x01400000 : "linux"
 +0x003db4dc-0x01400000 : "rootfs"
 +0x01400000-0x02600000 : "linux2"
 +0x015db4dc-0x02600000 : "rootfs2"
 +Creating 1 MTD partitions on "brcmnand":
 +0x02600000-0x03f00000 : "brcmnand"
 +u32 classifier
 +    Actions configured
 +Netfilter messages via NETLINK v0.30.
 +nf_conntrack version 0.5.0 (512 buckets, 4096 max)
 +ctnetlink v0.93: registering with nfnetlink.
 +nf_conntrack_rtsp v0.6.21 loading
 +IPv4 over IPv4 tunneling driver
 +nf_nat_rtsp v0.6.21 loading
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +TCP cubic registered
 +NET: Registered protocol family 1
 +NET: Registered protocol family 10
 +ip6_tables: (C) 2000-2006 Netfilter Core Team
 +IPv6 over IPv4 tunneling driver
 +NET: Registered protocol family 17
 +Bridge firewalling registered
 +Ebtables v2.0 registered
 +ebt_ulog: not logging via ulog since somebody else already registered for PF_BRIDGE
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Freeing unused kernel memory: 248k freed
 +Failed to execute /init
 +Failed to execute /sbin/preinit.  Attempting defaults...
 +Algorithmics/MIPS FPU Emulator v1.5
 +*******************************************************************
 +
 +                             |
 +                 .|||.       .|||.
 +             ..:|||||||:...:|||||||:..
 +             C i s c o   S y s t e m s
 +
 +   Copyright (c) 2011 by Cisco Systems, Inc. All Rights Reserved.   
 +   Booting bentley (firmware version 1.0.12.128947)
 +*******************************************************************
 +[utopia][init] System Initialization
 +No MTD partition located for /tmp, using tmpfs
 +
 +
 +
 +
 +bdutil board utility kernel module, version 1.2
 +bdutil board utility buttons kernel module, version 1.2
 +bdutil board utility LEDs kernel module, version 1.2
 +chmod: /tmp/etc/.root/passwd: No such file or directory
 +chmod: /tmp/etc/.root/shadow: No such file or directory
 +chmod: /tmp/etc/.root/group: No such file or directory
 +[utopia][init] Cannot find syscfg partition, assuming /dev/mtd6
 +[utopia][init] Using persistent syscfg data from /var/config/syscfg
 +[utopia][init] Starting system logging
 +[utopia][init] Starting sysevent subsystem
 +[utopia][init] Late loading usb drivers
 +[utopia][init] Setting any unset system values to default
 +0xb000000 0x1000000
 +system_state-normal|/etc/led/solid.sh ; system_state-error|/etc/led/blink_15_sec.sh ; system_state-heartbeat|/etc/led/blink.sh ; fwupd-start|/etc/led/blink.sh ; fwupd-success|/etc/led/solid.sh ; fwupd-failed|/etc/led/blink_15_sec.sh ; wps-running|/etc/led/blink.sh ; wps-success|/etc/led/solid.sh ; wps-failed|/etc/led/blink_15_sec.sh ; wps-stopped|/etc/led/solid.sh ; led_ethernet_on|/etc/led/rear_all_default.sh ; led_ethernet_off|/etc/led/rear_all_off.sh ;\
 +0xc000000 0x1000000
 +0xd000000 0x1000000
 +0xe000000 0x1000000
 +0xf000000 0x1000000
 +0x10000000 0x1000000
 +0x11000000 0x1000000
 +0x12000000 0x1000000
 +0x13000000 0x1000000
 +0x14000000 0x1000000
 +0x15000000 0x1000000
 +0x16000000 0x1000000
 +0x17000000 0x1000000
 +0x18000000 0x1000000
 +[utopia][init] Starting bdutil daemon
 +BDUTIL daemon mode
 +Wed Jun 29 17:10:00 UTC 2011
 +
 +
 +(none) login: Device is Broadcom Router
 +
 +
 +(none) login:
 +
 +(none) login: admin
 +Password: configuring interfaces for IGMP filtering
 +
 +Lighttpd Model Base: EA2700
 +LUA does not exist: copy lighttpd.conf to /etc folder
 +Setting SSID: "Cisco10925"
 +Login incorrect
 +Cisco10925 login:
 +Cisco10925 login: Auto channel do not set chanspec, Warning
 +
 +Cisco10925 login: Build temporary www configuration directory:
 +adminTSLIIHauhEfGE
 +
 +Password:
 +login: can't chdir to home directory '/tmp/home/admin'
 +/ $ Setting SSID: "Cisco10925"
 +Restarting nfqrecv service... 
 +</code>
  • Last modified: 2019/10/13 10:39
  • by tmomas