Letv LBA-047-CH

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.

FIXME Any text with a light background (like this one) provides instructions for creating the Details Page. When you have filled in correct/useful information (instead of any template that's there) remove the instructions, as well as the <WRAP> that encloses it.

Generic Router

For version 22.03.x:

  1. Set local IP to 192.168.67.100 and open tftpd64
  2. Connect LAN port to computer
  3. Rename factory.bin to openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin
  4. Make sure firmware file is in the tftpd's root directory
  5. Push reset button and plug in, keep reset button pressed for 5 seconds, and then it will download firmware from tftp server automatically

For version 23.x and later:

  1. Set local IP to 192.168.67.100 and open tftpd64
  2. Connect LAN port to computer
  3. Rename rootfs.bin to openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin
  4. Rename squashfs-kernel.bin to openwrt-ar71xx-generic-ap147-16M-kernel.bin
  5. Make sure firmware files are in the tftpd's root directory
  6. Push reset button and plug in, keep reset button pressed for 5 seconds, and then it will download firmware from tftp server automatically

FIXME Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

FIXME The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

  • How you install OpenWrt from a device freshly opened
  • The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

  • Browse to http://192.168.1.1/Upgrade.asp
  • Upload .bin file to router
  • Wait for it to reboot
  • Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

Specific values needed for tftp

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name Description Default configuration
br-lan EXAMPLE LAN & WiFi EXAMPLE 192.168.1.1/24
vlan0 (eth0.0) EXAMPLE LAN ports (1 to 4) EXAMPLE None
vlan1 (eth0.1) EXAMPLE WAN port EXAMPLE DHCP
wl0 EXAMPLE WiFi EXAMPLE Disabled

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) EXAMPLE 4
LAN 1 EXAMPLE 3
LAN 2 EXAMPLE 2
LAN 3 EXAMPLE 1
LAN 4 EXAMPLE 0

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The Letv LBA-047-CH has the following buttons:

BUTTON Event
EXAMPLE Reset reset
EXAMPLE Secure Easy Setup ses
EXAMPLE No buttons at all. -

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

  • To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for Letv LBA-047-CH
EXAMPLE 115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE


COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Space for additional notes, links to forum threads or other resources.

  • ...

FIXME Add tags below, then remove this fixme.

How to add tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1